service manual, power socket / light board
Contents
1. exposed board from the left hand side of the vehicle 5 0 Unplug the four connectors positioned along the left side of the board Take your Locking tabs time and be sure to release the locking tabs on them 5 1 If any of the connectors are too tight to release by hand a small screwdriver can be carefully used to separate them T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 7 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 0 2 Remove the two Phillips head screws holding this metal connector in as shown 9 3 Unplug the connector 6 0 Using the inch nut driver loosen the four nylock nuts fastening the board down Leave them finger tight and on the studs for now so you can remove them by hand to lessen the chance of dropping them T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 8 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 6 1 After removing the nylock nuts washers and grommets from the four studs lift the board out You may have to use a screwdriver to help lift it off the studs SS f y a Be sure to leave the T eT grommets under the board on the studs 7 1 Install the new P S light board Carefully align it on t 7 2 Place a grommet then a washer t2. SERVICE MANUAL Document Number e 040 00068 Form Instructions Equipment Equipment Manufacturer List 1 P S Light Control T3 Motion 2 Phillips screw driver small Any 3 1 4 inch nut driver Any 4 1 8 inch Allen wrench Any 5 Wire cutters Any 6 Blade screwdriver small Any Document Description Document Description Reference Docs Related Files Even Mam OOOO T3MOTION INC PROPRIETARY INFORMATION ALL TEXT AND GRAPHICS This document is the sole property of T3MOTION Inc The release of data COMPUTER GENERATED DO contained in this document and the reproduction of this document in whole SHEET 1 of 12 NOT REVISE MANUALLY or in part without the written permission of T3MOTION Inc is prohibited Form 040 00068 Rev 1 SERVICE MANUAL ent frame ern fy 020 00012 P S Light Control Assembly T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is D subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL Serious electrical shock can occur if precautions are not followed e ALWAYS TURN OFF POWER BREAKER IN GLOVE BOX AND REMOVE POWER MODULES BEFORE PERFORMING ANY ELECTRICAL WORK Power breaker in glove box Power modules e ALSO SET THE PARKING BRAKE PRIOR TO ANY WORK Parking brake T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data cont
3. ained on this sheet is 3 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL WORK INSTRUCTIONS 1 0 Recommended tools for replacing the power socket light board assembly See equipment table above for the details 1 1 2 0 ng the four plastic clasps T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is A subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 2 1 Squeeze tangs to release the clasps Me re aoe 4 3 0 Using the 1 8 inch Allen wrench remove the four fasteners that attach the access panel Remove the bottom two first 7 AN 3 1 T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 5 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 4 0 Remove the two small Phillips head screws holding the red pink board in place 4 1 Genily lower the hinged panel Do not force if it does not open all the way easily carefully guide the wires to allow for some slack in them aka Ws 4 2 T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 6 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 4 3 This is a view of the fully
4. hen a nylock nut on each stud and snug them down with the nut driver F j b N Nylock nut Washer Grommet T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 9 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 7 3 Donot over tighten the nylock nuts They only need to be snug Do not over compress the grommets They are for shock absorption gt 8 0 Reattach the metal connector with the two Phillips head screws 8 1 Plug the four connectors on the left side into their receptacles T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 10 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 9 0 Close the hinged red pink panel 9 1 Install the two small Phillips head screws to secure it T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 11 subject to the restriction on the cover or title page of this 040 00068 1 document SERVICE MANUAL 10 1 Hold panel in place and hand thread fasteners to start 10 2 Once all four fasteners are hand threaded tighten them down with the Allen wrench Do not over tighten they only need to be snug 10 3 Re install pannier bag by securing all four plastic clasps Cy F
5. x hake a ga gt ee te d Noy For addition information contact T3 Motion at 714 619 3600 T3MOTION PROPRIETARY INFORMATION Document No Revision Sheet Use or disclosure of data contained on this sheet is 12 subject to the restriction on the cover or title page of this 040 00068 1 document
Download Pdf Manuals
Related Search