L.E.D. HALO TRIM RINGS For PASSING LAMPS 7271
Contents
1. the Trim Ring PIC 4 this will help keep the harness from being pinched between the Halo Ring and the spot lamp STEP 5 Tighten the Phillips Pan Screw with a 2 Phillips Head Screwdriver while you hold the Custom Nut As you tighten the Screw make sure the back edge of the Trim Ring is in the groove on the driving light housing Gently shake the light after tightening to ensure the Trim Ring is secure NOTE If you have difficulty assembling the Halo Trim Ring and spot lamp using the OEM backing ring remove the Halo Trim Ring and the spot lamp from the housing Remove the OEM backing ring and apply one of the included foam strips to the back of each spot lamp PIC 5 Reinstall the lamp and Halo Trim Ring Foam strips may need to be trimmed for proper fit STEP 6 Route the wire harness from the Halo Trim Ring along the existing spot lamp harness to the inside of the fairing or headlight cowl Secure the harness with the included cable ties STEP 7 Repeat Steps 3 4 5 and 6 for the left side Proceed to the wiring section for your model It is the installer s responsibility to ensure that all of the fasteners NOTICE including pre assembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required WIRING FOR FLST MODELS STEP 8 Remove the left sitting on bike rear side of the headlight cowl as per the service manual S2. understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition Let cool NOTICE Avoid damage to the motorcycle Protect painted surfaces with a soft cloth or blanket NOTICE A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all of the steps in the procedure consult a trained technician NOTE Pictures shown are of chrome parts Installation of BLACK parts will be the same STEP 2 Determine the left from the right side sitting on bike Halo Trim Rings The wire will exit the Trim Ring towards the headlight PIC 1 CUSTOMER SERVICE INSTALLATION QUESTIONS LIMITED WARRANTY idl 11 y WOIK iansnip I C ABOUT OUR CATALOG STEP 3 Remove the stock trim ring from the Right spot lamp by removing the screw and nut from the ee bottom of the ring PIC 2 set these aside they will not be reused Hold on to the lamp Once the Kuryakyn trim ring is removed it can fall out STEP 4 Install the new Halo Trim Ring to the spot lamp using the included Phillips Pan Head Screw and Custom Nut The L E D Halo Light Ring will seat next to the front of the Trim Ring The post on the bottom of the Light Ring will fit in the notch on the bottom of the Trim Ring PIC 3 When the locating pin is between the notch gently press the harness against
3. INSTALLATION L E D HALO TRIM RINGS for PASSING LAMPS 7271 PARTS INCLUDED 1 Left Black Trim Ring and L E D Halo light 1 Right Black Trim Ring and L E D Halo Light 2 1 2 Wide Adhesive Foam Strips 1 Hardware Kit Including Female T Tap Connectors Male Spades 4 Black Nylon Cable Ties M3 Custom Nuts M3 Phillips Pan Head Screws Dielectric Grease Pack 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND NOTICES REGARDING THE USE AND CARE OF THIS PRODUCT re NN W OC THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY l This indication alerts you to the fact that ignoring the N OTI CE contents described herein may negatively affect product performance and functionality NOTICE IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF THE IMPORTANT INFORMATION CONTAINED IN THEM TOOLS SUGGESTED 2 Phillips Head Screwdriver Wire Crimping Tool Wire Cutter Wire Stripper STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and
4. T MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY Secure all wiring away from any moving parts pinch points or ex NOTICE treme heat Kuryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abraded melted or frayed wires WIRING FOR FLHR MODELS STEP 17 Remove the headlight from the headlight shroud per the service manual STEP 18 Locate the GRAY BLACK wire that operates the spot lamps PIC 8 Attach two of the included Female T Tap Connectors to this wire _ STEP 19 Locate a ground wire This is usually a BLACK wire Use the wire schematic in the service manual or a test light to confirm that you have a Ground wire Attach two of the included Female T Tap Connectors to this wire NOTICE K ryakyn recommends the use of dielectric grease on electrical connections STEP 20 Plug the Male Spades on the RED wires in the Halo Trim Ring harnesses to the Female T Taps on the GRAY BLACK stripe wire Plug the BLACK wires from the Halo Trim Ring harnesses to the determined Ground wire STEP 21 Test the Halo Trim Rings and spot lamps to see if they operate with the switch correctly Replace the headlight 4 WARNING ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY NOTICE It is the installer s responsibility to ensure that all of the fasteners including pre a
5. TEP 14 On 06 and Later Models Locate the stock turn signal connectors The connectors are located on the inside of the inner fairing mounted to each inner fairing brace PIC 6 There will be one violet wire one blue wire one gray wire and one black wire coming out of the connector Attach a Female T Tap Connector to the GRAY BLACK stripe wire on each side Attach a Female T Tap Connector to the BLACK wire on each side of this harness On 05 and Earlier Models Locate the GRAY BLACK wire that operates the spot lamps Attach two of the included Female T Tap Connectors to this wire PIC 7 Locate a ground wire This is usually a BLACK wire Use the wire schematic in the service manual or a test light to confirm that you have a Ground wire Attach two of the included Female T Tap Connectors to this wire POT ANF RERNE S MOUNTED HERE ON EACH SIDE OF INNER NOTICE K ryakyn recommends the use of dielectric grease on electrical FAIRING Daia connections STEP 15 Plug the Male Spades on the RED wires in the Halo Trim Ring harnesses to the Female T Taps on the GRAY BLACK wires Plug the Male Spades on the BLACK wires from the Halo Trim Ring harnesses to the Female T Taps on the BLACK wires STEP 16 Test the Halo Trim Rings and spot lamps to see if they operate with the switch correctly Replace the outer fairing A WARNING ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGH
6. TEP 9 Locate the GRAY BLACK stripe wire attached to the toggle switch mounted on the left rear cowl Install two of the included Female T Tap Connectors to this wire STEP 10 Locate a ground wire This is usually a BLACK wire Use the wire schematic in the service manual or a test light to confirm that you have a Ground wire Attach two of the included Female T Tap Connectors to this wire NOTICE Kuryakyn recommends the use of dielectric grease on electrical connections STEP 11 Plug the Male Spades on the RED wires in the Halo Trim Ring harnesses to the Female T Taps on the GRAY BLACK stripe wire Plug the BLACK wires from the Halo Trim Ring harnesses to the determined Ground wire GENTLY PRESS HARNESS AGAINST TRIM RING STEP 12 Test the Halo Trim Rings and spot lamps to see if they operate with the switch correctly Replace the headlight cowl WARNING ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY APPLY FOAM STRIP TO LAMP Secure all wiring away from any moving parts pinch points or extreme heat NOTICE Kuryakyn WILL NOT issue a warranty on any electrical component that fails due to pAGE pinched crimped broken abraded melted or frayed wires 2 L E D HALO TRIM RING SPOT LAMPS INSTALLATION cont WIRING FOR FLHT MODELS ee STEP 13 Remove the outer fairing as per the service manual Kuryakyn S
7. ssembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic PAGE maintenance may be required 3 Ride On L E D HALO TRIM RING SPOT LAMPS INSTALLATION
Download Pdf Manuals
Related Search