AUTOMOTIVE TESTER 2201
Contents
1. writing to 5 F East 304 Bldg Shangbu Industrial Park Zhenxing Rd Futian Shenzhen China to request written permission to use materials on this manual for purposes or for other questions relating to this manual T NS PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS Disclaimer All information in this manual is based on the latest product information and is believed accurate at the time of publication However specifications and procedures are subject to change without notice All information illustrations and specifications contained in this manual are based on the latest information available at the time of publication The right is reserved to make change at any time without obligation to notify any person or organization of such revisions or changes Furthermore AUTOBOSS shall not be liable for errors contained herein or for incidental or consequential damages including lost profits in connection with the furnishing performance or use of this material To take full advantage of the unit you should be familiar with the OEM computer systems that are supported This manual tells you how to use the unit to perform diagnostic test and to find possible locations of vehicle problems It does NOT tell you how to correct the problems Consult your OEM vehicle service manual for repair instruction If you experience a problem obtaining service data from a vehicle it may be due to a veh2. cover of the multimeter Change a new fuse with the same specification Close the back cover and screw it 6 The specification of the fuse is 0 2A 250V 7 Take out the battery and put it in dry and ventilation places if you DO NOT use the multimeter for a long time 8 DO NOT try to change the interior circuit Accessory 1 User Manual 2 Quality Certificate 3 Protection Mould 4 Testing Leads 5 Type K Thermal Coupler Option SMD clamper can be used to test the parameter of the resistance capacitance inductance and transistor 24 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL PERSONS WHO PURCHASE AUTOBOSS PRODUCTS FOR PURPOSES OF RESALE AUTOBOSS is warranted against defects in materials and workmanship This warranty does not cover any Autoboss that has been abused altered used for a purpose other than that for which it was intended or used in a manner inconsistent with instructions regarding use The sole and exclusive remedy for any Autoboss found to be defective is repair or replacement at the option of AUTOBOSS in accordance with procedures established by AUTOBOSS In no event shall AUTOBOSS be liable for any damages direct or indirect special incidental or consequential or compensatory including without limitation lost profits for any representations breaches or defaults arising out of the use of this manu
3. read lead Connect the testing lead in parallel with the tested diode The multimeter will display the positive voltage drop for the diode with the unit is V The multimeter will display over range when the diode connected in the opposite direction Note a When the circuit is open the multimeter will display over range Normally the current for the tested components is 1mA l tcan be used to check the conditions of the rectifier diode 19 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 10 On Off Testing a Turn the Function Range knob to the scale of e b Insertthe black lead into COM hole and the red lead into the hole with 965 Connect the testing lead in series in the circuit The buzz will make the sound of Di Di when the resistance is lower than 50 Q Note Check the circuit when the power off otherwise an error will come up 11 Holding Function The multimeter will display the letter H when the Hold button pressed It is easy for you to read the measured values with this function The letter H will disappear when the button pressed again 12 Dwell Measuring Insert the black lead into COM hole and the red lead into the hole with V Q 965 b Turn the switch to the scale of DWELL according to the cylinder numbers Connect the black lead to ground or the negative of the battery and the red lead to the low voltage terminal of the distributor See the follow
4. Multimeter 2201 AUTO30SS AUTOMOTIVE TESTER 2201 AUTO30SS Copyright by Autoboss Tech Inc 1 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS CONTENTS TRADEMARK INFORMATION sss 2 DISOLAIMER 3 COPYRIGHT INFORMATION sss 4 PRECAUTIONS cccccccccesssssesesesesescsessseseeeseseseaeueeeneeseseasaeaseeeeees 5 INTRODUCTION te tete tede tette dete ete 8 TECHNICAL 0020200 022 2 200 6 600000000009 10 FRONT BOARD OF DIGITAL AUTOMOTIVE 13 OPERATION CS 13 MEASURING DC VOLTAGE sss 14 MEASUREING AC VOLTAGE 16 MEASURING DC AMPERAGE sss 16 MEASURING AC 17 MEASURING 11 1422220 002020 0 0 0 0 0 00 17 MEASURING DUTY 18 MEASURING TEMPERATURE sse 18 MEASURING TRIODE hFE 19 MEASUREING 2 2 2 2 2 22041000204 00 000000000000 19 ON OFF tnnt nnns 20 TN PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS HOLDING FUNCTION esee eee 20 DWELL MEASURING cessent nennen nentes 20 RPM MEASURING cte ad ep
5. ad into COM and the red lead into the hole V Q 965 And then connect the lead to the tested load in parallel The multimeter will display the value of the voltage and the polarity of the red lead at the same time Note a Turn the Function Range knob to the maximum before measuring the voltage b The voltage of the tested load is out of the testing scope when the displayed value is 1 You should change another higher range c The symbol of A means the voltage must be lower than 1000V otherwise the multimeter will be damaged d attention to the safety when testing the high voltage Application 1 Testing the distributor with DC 2V testing scope A Take down the high tension from the cap of the distributor and short it to ground B Connect the red lead to the low voltage terminal of the distributor or the negative of the ignition coil connect the black lead to the ground or the negative of the battery C Turn on the ignition switch for a while and the multimeter will display the value The value should be lower than 1V D Measure the voltage of the contact If the displayed value is lower than 0 2V it proves that the contact is good 14 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Application 2 Leakage testing by DV 2V testing scope A Connect the black lead of the multimeter to the negative of the battery and the red lead to the positive of the battery B If th
6. adings large LCD display as well as protective mould Unique protective device for wrong operation The testing port of mA or 20A can only be opened when the current option is chosen otherwise a blockage will work at the moment for the protection A PTC thermal element is connected with the input port V Q so as to guarantee the safety and lifetime as well as the switches for range scope Used to test the voltage amp current of DC the voltage amp current of AC resistor duty temperature parameter of diode and triode open circuit dwell and TACH Portable tester for automobile testing and maintaining engineering lab testing production testing field work and home electric appliances repairing etc Electric symbol DEWLL 3 P6 BUZZ e AC me DOUBLE ISOLATION LOW BATTERY Ft TACH O ALARM A HIGH PRESSURE GND AD OR DC nd DIOAD MC Ta B PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 0 55 CYL CE DUTY Features 1 Low power consumption CMOS double differential A D converter integrated circuit automatic zero calibration automatic pole displaying data storing low energy consumption and large measuring range 2 Accuracy of the current 0 5 Dwell 0 1 C 120 C RPM measuring 10RPM 10000RPM Temperature 20 C 1000 C Automatic power off the power will be turned off automatically 15
7. al Customer agrees to indemnify AUTOBOSS and hold it harmless against all claims and damages including without limitation reasonable attorney s fees arising out of the use of this manual unless such claims or damages result from the infringement of any copyright or other proprietary right of any third party No one is authorized to make any statement or representation altering the terms of this warranty No agent employee or representative of AUTOBOSS has any authority to bind AUTOBOSS to any affirmation representation or warranty concerning AUTOBOSS automotive meters except as stated herein 59622 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Disclaimer THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Specifications contained in this book are based on the manufacturers information and were believed accurate at the time of publication All information illustrations and specifications contained in this technical manual are based on the latest information available at the time of publication The right is reserved to make change at any time without obligation to notify any person or organization of such revisions or changes Furthermore AUTOBOSS shall not be liable for errors contained herein or for incidental or consequential damages including lost profits in connection with the furni
8. e multimeter displays a certain value it proves that the battery is leaking The best way is to clean the battery immediately Application 3 Testing the loading capacity with 20V testing scope A Connect the black lead to the negative of the battery and the red lead to the positive of the battery respectively B Turn on the headlights the flash light switch the ignition switch and the radio C The operating time is no longer than 2 minutes D Checking the displayed values If the value is lower than 11 7V you should change another battery or charge it Application 4 Testing the battery capacity by 20V testing scope A Take down the high tension from the cap of the distributor and short it to ground B Connect the black lead of the multimeter to the negative of the battery and the red lead to the positive of the battery C Start the engine for 15 seconds and check the displayed values If the value is higher than 9 1V it proves that the battery is ok Otherwise you have to check the engine or charge the battery or replace it Application 5 Testing the battery cable A Test the voltage of the battery cable as well as the working conditions when starting the engine 15 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Application 6 Checking the charging system Application 7 Checking the voltage regulator 2 Measuring AC Voltage a Turn the Function Range knob to the ACV testing
9. icle manufacturing design change 3 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS Copyright Information All rights reserved Printed in the People s Republic of China No part of this publication may be reproduced stored in a retrieval system or duplicated or transmitted in any manner or by any means electronic mechanical photocopying recording without prior written permission of AUTOBOSS The information contained herein is designed only for the use of this unit AUTOBOSS is not responsible for any use of this information as applied to other units Neither AUTOBOSS nor its affiliates shall be liable to the purchaser of this unit or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this unit or unauthorized modifications repairs or alterations to this unit or failure to strictly comply with AUTOBOSS operating and maintaining instructions AUTOBOSS shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original AUTOBOSS Products or AUTOBOSS Approved Products by AUTOBOSS General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners AUTOBOSS disclaims any and all rights in those marks 4 PDF created with pdfFactory tria
10. ing pictures d Start the engine and read the dwell by the multimeter 20 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 2859 m Black cable Red cable m Ignition Switch Plug Battery li wawawa Ignition Coil Distributor Picture for Dwell 13 RPM Measuring a Insert the black lead into COM hole and the red lead into the hole with V Q 965 b Turn the switch to the TACH scale according to the engine cylinders C Short the black lead to ground or the negative of the battery and the red lead to the low voltage terminal of the distributor or the negative of the ignition coil See the following pictures d Start the engine The engine speed is the measured values times 10 The unit is rpm 21 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Black cable Red cable 2020 Ignition Switch q q Battery ami Plug Ignition Coil Distributor Picture for RPM testing 14 Mechanical Protection The multimeter has a movable plate It can protect error operation The plate can move between the function and range knob The mechanical protection is listed as following The symbol e means the hole is blocked The black lead can insert into the hole The hole blocked Position of Switch E vows mA 20A Voltage for DC and AC Current over 20A for DG N and AG 22 PDF created wi
11. input current 20A less than 15s 10 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Voltage drop 200mV voltage drop for the full range 4 AC Amperage Range Accuracy Resolution 20mA 1 3 10u A 200mA 1 8 3 100 u A 20A 3 7 10mA Over load protection 0 2A 25 A fuse no fuse fro the ranges of 20A Max input current 20A less than 15s Voltage drop 200mV voltage drop for the full range Frequency 40Hz 400Hz Display average value sine wave effective value 5 Resistor Range Accuracy Resolution 200 2 0 8 3 0 19 ia 0 8 2 ue 200K 9 1009 20MQ 1 5 10K 9 Over load protection 250V DC or AC effective value Open circuit voltage 700mV 6 Duty Range Accuracy 0 1 99 9 1 5 7 Temperature Range Accuracy Resolution 20 C 0 C 59645 11 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 0 C 400 C 400 C 1000 C 1 3 1 C 29644 1 C 8 Transistor Triode hFE Parameter Testing Range Description Testing Conditions Testing the parameter of NPN or PNP hFE triode hFE The range is 0 10008 l is about 10 u A Vee is about 2 8V 9 Diode and On Off Testing gt 1mV voltage drop for Diode I Tes
12. l version www pdffactory com Multimeter 2201 AUTO30SS Precautions 1 Safety Precautions Please read the following precautions carefully before using Digital Automotive Tester 2201 As the battery liquid contains sulfuric acid take care to avoid direct contact of it with your skin Special attention should be paid to avoid splashing battery liquid into your eyes and keep it away from fire There are various kinds of poisonous venomous compounds such as hydrocarbon CO NO in the vehicle exhaust gas Avoid breathing this gas Park vehicle in a well ventilated place while testing The temperature is very high while the engine is running Avoid touching water tank and vent pipe and any other parts with high temperature v gt 5 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS Before starting engine be sure to apply the hand brake and block the front wheels and shift the gear rod in the neutral position manual transmission or the P position automatic transmission Remember to wear protective gloves while performing the test If you use the battery as power supply connect the RED jaw to the positive terminal and the BLACK jaw to the negative terminal 2 Precautions on Testing with 2201 Read this instruction carefully before testing The digital automotive tester 2201 is designed meeting the requiremen
13. minutes after the power on for the protection 7 Mechanical protection for full range overload 8 Maximum value 1999 3 1 2 9 Large LCD display 70x48mm the height of the letter up to 28mm 10 Power 9V battery NEDA1604 6F22 or similar 11 Low voltage alarm 3 12 Dimension 192x88x42mm 13 Weight 600g including battery and mould 14 Working condition Temperature 0 C 40 C Relative Humidity lt 85 Temperature 10 C 50 C Relative Humidity lt 85 Optimum Temperature 23 C 5 C Relative Humidity lt 75 9 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Technical Parameters 1 DC Voltage Range Accuracy Resolution 2V 1 20V 0 5 2 10mV 200V 100mV 1000V 0 8 3 1V Input Impedance 10M 9 Over load protection DC 1000V or AC 700V effective value 2 AC Voltage Range Accuracy Resolution 2V 1 20V 0 8 3 10mV 200V 100mV 700V 1 2 5 1V Input impedance 10M 9 Frequency 40Hz 400Hz Over voltage protective DC 1000V or AC 700 effective value Display average value sine wave effective value 3 DC Amperage Range Accuracy Resolution 20mA 0 8 2 104A 200mA 1 2 2 1004 A 20A 2964 5 10mA Over current protective 0 2A 250A fuse no fuse for the range of 20A Max
14. p ge Htc ta pena 21 MECHANICAL PROTECTION essen 22 SELECTING ANGEL OF THE 23 LISAS ectetuer etal 23 ACCESSORY L u gesc tate re dE eie ede 24 OPTIONS H 24 WARRANTY rene 25 3 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS Trademark Information AUTO3OSS is a registered trademark of Autoboss Tech Inc in China and other countries All other AUTOBOSS trademarks service marks domain names logos and company names referred to in this manual are either trademarks registered trademarks service marks domain names logos company names of or are otherwise the property of AUTOBOSS or its affiliates In countries where any of the AUTOBOSS trademarks service marks domain names logos and company names are not registered AUTOBOSS claims other rights associated with unregistered trademarks service marks domain names logos and company names Other products or company names referred to in this manual may be trademarks of their respective owners You may not use any trademark service mark domain name logo or company name of AUTOBOSS or any third party without permission from the owner of the applicable trademark service mark domain name logo or company name You may contact AUTOBOSS by sending an e mail to marketing autoboss net or
15. r by 20M Q 6 Measuring Duty a Turn the Function Range knob to DUTY scale b Insert the black lead into COM hole and the red lead into the hole with V Q 963 7 Measuring Temperature Turn the Function Range knob to C scale Insert the testing plug of the thermal coupler into the mulitimeter socket when testing the temperature Pay attention to the polarity of the positive and negative Put the testing end of the thermal coupler to the tested parts The multimeter will display the temperature values The unit is degree Note a The displayed values are the temperature of the tested parts when the thermal coupler inserted into the socket 18 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 The displayed values are the environmental temperature when the circuit is open b The temperature limit for the thermal coupler TP 01 K provided by the factory is 250 C The limit value can reach 300 C in a short period 8 Measuring Triode hFE Parameter a Turn the Function Range knob to the hFE scale b Check the type of the Triode Insert the Pin E B C into the right holes c The displayed values are approximate The current for the basic polarity is 10 A and the voltage is 2 8V 9 Measuring Triode a Turn the Function Range knob to the p scale b Insert the black lead into COM hole and the red lead into the hole with V Q 965 Pay attention to the polarity of the
16. scope b Insert the black lead into COM hole and the red lead into the hole with the symbol of V2 965 Meanwhile parallel the lead to the tested load Note a Turn the Function Range knob to the maximum before measuring the voltage b The voltage of the tested load is out of the testing scope when the displayed value is 1 You should hange another higher range c The symbol of Z means the voltage must be lower than 700V otherwise the multimeter will be damaged d Pay attention to the safety when testing the high voltage 3 Measuring DC Amperage a Take out the testing lead and turn the Function Range knob to the DCA testing scope b Insert the black lead into COM hole and the red lead into the hole with mA or 20A Connect the testing lead in series in the circuit The multimeter will display the readings as well as the polarity of the red lead Note a Turn the Function Range knob to the maximum before measuring the voltage 16 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 b The voltage of the tested load is out of the testing scope when the displayed value is 1 You should change another higher range c The overload will damage the in built fuses when testing by mA scale The specification of the fuse is 0 2A 250V d Never exceed 15 seconds when testing the load by maximum current 20A There is no fuse at the scale of 20A 4 Measuring AC Amperage a Take o
17. shing performance or use of this material To take full advantage of the unit you should be familiar with the OEM computer systems that are supported This manual tells you how to use the unit to perform diagnostic test and find possible locations of vehicle problems It does NOT tell you how to correct the problems Consult your OEM vehicle service manual for repair instruction If you experience a problem obtaining service data from a vehicle it may be due to a vehicle manufacturing design change Vehicle manufacturers now introduce new product lines year round To obtain test data on a mid year vehicle you may need to program the tester to the next model year available in the software cartridge not the actual VIN year of the vehicle being tested 26 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Order Information Replaceable and optional parts can be ordered directly from your AUTOBOSS authorized tool supplier Your order should include the following information 1 Quantity 2 Part number 3 ltem description Customer Service For any quality problems please contact the local distributor or direct contact Autoboss Tech Inc Autoboss Tech Inc 5 F East 304 Bldg Shangbu Industrial Park Zhenxing Rd Futian Shenzhen China Tel 0086 755 83285146 Fax 0086 755 82170248 E mail marketing autoboss net Website www autoboss net 27 PDF created with pdfFactory
18. th pdfFactory trial version www pdffactory com Multimeter 2201 Current within 20A for DC N and AC Resistance Q e e gt Triode hFE parameter e Duty Temperature Dwell rpm e e The Function Range knob cannot move if you forget to pull out the testing leads Pull out the testing leads before turning the Function Range knob otherwise the mechanical protection will be damaged 15 Selecting the angel of the Multimeter A protection mould provided for the protection You can adjust the holder for the readings at different angles Maintenance Digital automotive tester 2201 is an accurate tool It should be kept carefully 1 Do not test the DC voltage higher than 1000V or AC voltage higher than 700V with digital automotive tester 2201 2 Pull out the testing leads before turn the Function Range knob Otherwise the mechanical protection will be damaged 3 Do not use the digital automotive tester 2201 if the back cover is not in the right position 259 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 4 Pull out the testing leads or turn off the power before exchange a new battery Turn out the screw and push the battery cover Take down the battery cover and change a new battery with the same specification 5 Pull out the testing leads or turn off the power before exchange the fuse Turn out the screw and open the back
19. ting Range Resolution Description Sandile Positive DC amperage is Displaying the positive about 1mV Negative DC voltage is about 2 8V Buzz will work when the e resistor of the circuit is lower than 500 Open circuit voltage is about 2 8V Over load protection 250V DC or AC effective value 10 Dwell for Distributor Contactor Cylinder Range Accuracy Resolution 3CYL 0 120 1 22 2 041 4CYL 0 90 5CYL 0 72 12 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 6CYL 0 60 8CYL 0 45 11 Rotation Speed rpm CYL Range Accuracy Resolution 3CYL 500 10000 5CYL RPM 1 29642 10RPM 6CYL 8CYL Front Board of Digital Automotive Tester 1 Description Operation Press down the Power switch If the battery voltage is too low the symbol LCD Display Hold switch Range knob Temperature socket Insert COM Power switch Triode socket Sliding plate 69 C 9 amp 9 will be displayed on the left upper screen You should change a new battery Select the required functions and testing ranges 13 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 1 Measuring DC Voltage D Turn the Function Range knob to the DCV range scope Insert the black le
20. trial version www pdffactory com
21. ts of Class Il and GB 4793 1 Pollution and IEC 1010 on Electronic Testing Instrument over voltage CATII tis forbidden to make a test with back cover open since there is a danger of electric shock Check the harness of electronic probes damaged or worn out before testing Electronic probes must be pulled out first and then turn the Function Range Switch before enter or exit the current ranges in order to protect the mechanic devices The input signal must not exceed the nominal value otherwise it will damage the tester Do not turn Function Scope Switch while testing The potential drop will not exceed 1000V between COM and GND otherwise the operator will be shocked Be careful when the voltage is higher than DC 60V and eae PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS 42N Please change a new battery for precision in time testing when the symbol of E displayed Always use the same specification fuse for the instrument This tester is an exact electronic system never break or hit it while operating Before testing select the correct testing scope and correct testing leads Never try to repair the unit E PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 AUTO30SS Introduction Digital Automotive Tester 2201 Newly developed digital automotive tester 2201 with super design easy operation accurate re
22. ut the testing lead and turn the Function Range knob to ACA testing scope b Insert the black lead into the COM hole and the red lead into the hole with mA or 20A Connect the testing lead in series in the circuit Note a Turn the Function Range knob to the maximum before measuring the voltage b The voltage of the tested load is out of the testing scope when the displayed value is 1 You should change another higher range c The symbol of Z means the voltage must be lower than 1000V otherwise the multimeter will be damaged d Pay attention to the safety when testing the high voltage 5 Measuring Resistance a Turn the Function Range knob to Q testing scope b Insert the black lead into COM hole and the red lead into the hole with V2 Connect the testing lead in parallel in the circuit E 7 2 PDF created with pdfFactory trial version www pdffactory com Multimeter 2201 Note a When the circuit is open the multimeter is in the testing state the display the maximum b When the tested resistor is higher than 1M 0 the mulitimeter will display the stable values after few seconds It is normal for testing high resistant C Turn off the power supply for the tested circuit and let the capacitor discharge when testing the resistors which is already connected in the circuit Application 1 Testing the impedance by the scale of 20 9 and 200k Q Application 2 Checking the working conditions of the capacito
Download Pdf Manuals
Related Search