650226c MCL-3000 SPD_with cable
Contents
1. is displayed e Release the switch The display will switch to unit and light up the current speed unit MPH or km h e Press and hold the switch to keep the current unit or press and release the switch to change the unit e Next the system will restart with AdJUu5e amp on the message display The speedometer will show the speed reading Begin driving at a known speed When the switch is pressed the speedometer reading will begin increasing until the switch is released The next time the switch is pressed the reading will begin decreasing until it is released When the speedometer is correct you can release the switch The new calibration will be saved if no adjustments are made for 10 seconds PLEASE NOTE Common problems during calibration gt VSS vehicle speed sensor wires should be isolated from the ignition system Coils plug wires or tachometer signal wires routed near or with the VSS wire can cause many problems If you are seeing erratic speedometer operation registering speed at a standstill or speed changes with engine RPM please double check your VSS wire and tachometer wire routing making sure the VSS wire is separated from any ignition system components gt If your speedometer registers O0 all the time the unit is not receiving a VSS signal please double check your sensor wiring and mounting The speedometer cannot be properly calibrated until you are registering a stable but incorrect soeedomet2. including any implied warranty of merchantability shall be limited to the duration of this written warranty Any action for breach of any warranty hereunder including any implied warranty of merchantability must be brought within a period of 24 months from date of original purchase No person or representative is authorized to assume for Dakota Digital any liability other than expressed herein in connection with the sale of this product x IN D 4510 W 6lst St North Sioux Falls SD 57107 Fax www dakotadigital com Phone 605 332 6513 605 339 4106 Fr dakotasupport dakotadigital com Copyright 2011 Dakota Digital Inc 16 MAN 650226 C
3. Press and release the switch to save the 2 3 reading The display will show 99 and then switch to displaying the measured resistance Add more fuel to fill the tank full Press and release the switch to save the full reading Press and hold until con is displayed to save the settings The gauge will then return to normal operation VOLT SETUP The volt gauge has user settable low and high voltage warning points that will make the gauge flash as a warning indicator when either of the conditions are met or exceeded To enter setup press and hold the switch while turning the key on Release the switch The gauge will show Press and release the switch until ui amp is displayed then press and hold the switch until L0 is displayed Press and release the switch until the desired low voltage warning is displayed Press and hold the switch until H P is displayed then release the switch Press and release the switch until the desired high voltage warning point is displayed Press and hold until is displayed to save the settings Turn the key off 14 MAN 650226 C Speedometer Troubleshooting guide Problem Possible cause Solution Gauge will not light up Red wire does not have power Connect to a location that has power Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge lights up but speed Gray wire is not
4. Y B id m Installed oil temp sensor and harness plug TC Temp sensor installed as drain plug EVO Plug in the sealed two pin connector and route the wires over to the bottom right side frame rail Begin running the wires back and up behind the transmission and starter area to the battery box following the wiring harness that is in place Use zip ties to secure the wire harness to the other wires along the frame 7 MAN 650226 B Once you have the wires up through the battery box area it is recommended you remove the tank bolts to continue running the harness under the tank to its final destination behind the fairing Use a firm wire and some electrical tape to fish the wires up the backbone under the tank filler rod welding wire works well for a fish tape Once clear of the tank follow the factory wiring harness on the right side and route wires behind the fairing and over to the oil temp gauge Make sure to replace and tighten the tank bolts when done r Remove front tank bolts to loosen tank x Vi y SAA Pull the temp sensor wires through the fairing Route wires under tank Now you will have to de pin a couple wires to connect the temp sensor wires to the factory plug to allow a factory style plug in connection to the gauge The pins in the connector have a small locking tab on the back flat side of the terminal seen in the picture below Use a small allen wrench pick or small screw driver to bend and release thi
5. constant power is pin 10 on the radio This should be a Red w Orange wire that is fused to the battery Oil Pressure Voltage and Fuel Level connection There are four two pin harnesses that are coming out of the adaptor box with a blue and green wire in each This will plug into the back of each small round gauge these wires are the switch green and dim blue wires Route one of these harnesses to the back of each small gauge and plug it in It does not matter what harness goes to what gauge as they are all the same Now you can plug in the 3 pin power and sender connections for the small gauges Plug the original oil pressure voltage and fuel connectors directly into the new gauges Oil Temperature connection The air temperature gauge is replaced with an oil temperature gauge and this connector will need to be changed instructions on how to install and connect the sensor begin on the following page OIL TEMPERATURE SENSOR Evolution Engines The supplied temp sensor will need to be used with the included brass adaptor bushing 1 2 straight to 3 8 npt You will need to use the supplied adaptor and install it in place of the oil drain plug The new adaptor and sensor will now be the drain plug and will have to be unplugged and removed for oil changes The factory o ring is used to seal the adaptor to the pan and should be replaced at oil changes First install the new o ring and thread the sensor into the adaptor Once the sensor is tig
6. each gear and seeing if positions agree 5 9nAL Tach signal setup Press and release the switch until 5 SnAL is displayed then press and hold the switch until is displayed Release the switch The setting will be displayed i HiorS L IZ His the normal setting Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed 13 MAN 650226 C OIL PRESSURE SETUP The oil pressure gauge can be set for various stock Harley pressure senders There is a display update setting for how fast the numbers will change as well as a user settable low and high pressure warning points When a warning condition is reached the gauge will flash the reading as a warning indicator The stock sender for 2004 and up should be the 60 psi sender For higher pressure and more accurate pressure readings one of two Dakota Digital senders may be used 0 75 psi SEN 1032 or 0 150 psi SEN 1031 sold separately To enter setup press and hold the switch while turning the key on Release the switch The gauge will show Press and release the switch until FS is displayed then press and hold the switch until Snrd is displayed Press and release the switch until the correct sender type is displayed 40 for 96 98 stock sender 60 for 99 up stock sender 15 for Dakota Digital 75 psi 150 for Dakota Digital 150 psi Press and hold the switch u
7. other gauges will exit setup and allow the selected gauge to be changed To get into setup press and hold the function switch while turning the key on Press and release the switch to advance through the menus below when on the desired option press and hold the switch to select setup for that particular gauge function speed__ tach oilpsi__ oiltemp Fuel volt io a ee ee eee es ee a FACTORY DEFAULT SETTINGS FOR SETUP MENUS Below is a list of all of the factory gauge settings and what can be adjusted in the setup menus You can calibrate and adjust gauges as often as you wish however they should only need to be set once Most gauges will function properly from the factory only desired warning points will need adjustment The fuel sender needs to be set per application as well The only gauge that may require setting after the initial install is the Clock function on the tachometer so it is the first setup menu Speedometer Tachometer Unit MPH Engine cylinders 2 Service meter OFF Signal type 12 HI 12V ignition signal Performance Menu ON Night Dimming 1 darkest Display Update 3 fastest 1 8 sec RPM Warning 5500 range 2200 9900 Pressure Gauge Volt Gauge Sender 60PSI user selectable Lo warn 11 1 V range 9 6 12 6 HI warn 51 PSI range varies with sender Hi warn 15 4 V range 13 9 16 9 Lo warn 7 PSI range 02 32 psi Oil Temp Gauge Fuel Gauge Sender Set to deg F user selectable scale Sender 10 ohm sender user selecta
8. start Remove the outer fairing this will vary from model to model please follow the service manual to expose the wiring and gauges Don t be alarmed by the amount of wires behind the fairing this is a direct plug in kit and these detailed instructions will guide you through it ae s oi CA Se ro R W VA Rte A Ultra FLHT with outer removed Road Glide FLTR outer removed Remove Factory Gauges Now you are ready to start unplugging and removing the gauges Start with the speedometer and tachometer gauge plugs and speedometer cable if you are working on a cable drive bike 1996 1999 ULTRA FLHT batwing fairings Remove the clamps that hold the Speed and Tach in place with a screw driver or wrench depending on application and remove the gauges en J i E Ai gt _ j i Remove speedo cable unplug gauges Remove nuts screws and clamp to remove factory gauges ROAD GLIDE FLTR You will need to remove the speedometer and tachometer instrument bezel To do this remove two small screws on the left and right side of the bezel Then lift up on the back of the bezel and slide the tab that is under the ignition switch out from under the switch cover see photos below of ignition switch cover removed to show detail Now unplug the gauge connections cable where applicable Remove switch and unplug the idiot lights so the bezel can be completely removed for easier installation of the new gauges Remove the clamp s that hold the gauges
9. to the bezel and remove the gauges and grommets gaskets f 10 i D at so LILIS rn f a A K s m t p J I e p a D ve Y a 7 aS Ler e N f Picture of tab switch cover removed Bezel removed Gauges Grommets removed 2 MAN 650226 B All of the small gauges fuel volts oil and air temp have two plugs One is for illumination and the other is for the gauge power ground and sensor The illumination harness two pins orange and black wires will not be reused and can hang freely inside the fairing with the bulb removed or can be secured to the other gauge wires to clean things up The three pin connector will be used to connect all of the new Dakota Digital small round gauges Unplug connectors at the back of the 4 small round gauges then remove the two 5 16 nuts holding the clamps onto each small gauge and remove the gauges New nuts for the small gauges are included in the hardware pack DO NOT reuse the stock nuts for the new gauges they are not the same thread Removal Tip for FLH s It is recommended to leave the mounting bracket in place on the lower two gauges and then push the gauge out the front of the fairing and disconnect the wires in front of the faring so things can be reached a little easier Reconnect the factory three pin connector to the new oil pressure gauge and also route and connect the new two pin switch amp dimming connectors before installing the gauges On the t
10. while turning the key on and starting the engine Once the engine is running release the switch Press and release the switch until ELH is displayed Press and hold the switch until is displayed Press and release the switch until SEA is displayed press and hold the switch until is displayed The message will show LU ELH if the engine rpm is below 1500 or LU 5Fd if the vehicle speed is below 5 Begin driving in 1 gear The display should show JEAr and the should be flashing Drive at a steady speed until the 1 stops flashing it should only take about 20 seconds if the speed and RPMs are steady gt Optionally If the gear does not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Shift to 2 gear and drive at a steady speed The display will change to a flashing 2 Wait until the 2 stops flashing then 3 should start flashing shift to the next gear and continue gt Optionally If the gears do not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Repeat this through each gear When you are done come to a complete stop or press and hold the switch until the display shows SEER Turn the key off and then on again to restart the gauges in normal operation verify the gear position by riding through
11. wiring connections Blue wire should have 0 volts times all of the time when tachometer is bright Security indicator does Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 0 volts not work when the it should be off and about 12 volts when te indicator should be on gt Engine indicator does Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 12 volts not work when the it should be off and about 0 volts when the indicator should be on Speed sensor voltage checks All checks should be made with the sensor connected to the gauge and the key on Checks should be done with a voltmeter and not a test light Checks for the 3 wire sensor should be made between each individual wire and ground 3 wire sensor Red wire should have 9 11 volts dc slightly less than battery voltage sometimes 5V if supplied by factory harness Black wire should show ground 0 volts dc at all times White wire should vary between 0 and 5 volts dc as the gear teeth or a steel object passes by the sensor Aluminum and Stainless Steel will not work with a Hall effect sensor This can be checked with the sensor mounted and spinning the rear tire slowly or by removing the sensor and moving a steel object pass the face of the sensor 2 wire sensor Measure the voltage between the two sensor wires With the wheel spinning the voltage should be about 1 10 volts ac make sur
12. ALE set rom update rate for digital readout LUA rh set rom shift warning point SEAr transmission gear programming 5 IAAL select 12 HI normal or 5 LO low voltage tach signal The gauge can be set to read from 1 15 cylinder ignition signals It can also be set to read either 12 volt tach signals or 5 volt tach signals found on some engine computers The digital tachometer update rate can be adjusted between slow mid and fast The rom warning shift point can be adjusted from 2200 9900 The tachometer will read from 350 9 990 rpm Press and hold the switch while turning the key on Release the switch Press and release the switch until tCH is displayed then press and hold switch until is displayed The rom display will show Set and the lower display will show night Press and release the switch to move through the different menus press and hold the switch to select a menu option Note The tachometer calibration may require you to hold the switch while starting the bike only if you are going to adjust set the GEAR programming since you will have to ride the bike Some ignition systems may disrupt power to other circuits causing the gauge to reset this is why you must hold the switch wile starting if you are setting up the GEAR display All other gauge functions and gauges can be set without running the engine CL CLOCK SETUP The time is displayed on the smaller display below the RPM It will not light up until the o
13. N ezkero ieiz WWW DAKOTADIGITAL COM Vv MCL 3000 gauge kit Gauge kit for 1996 2003 Models Thank you for purchasing the Dakota Digital MCL 3000 gauge kit for your Harley Davidson Touring bike This kit is designed to be a direct plug in replacement for all touring models from 1996 2003 Dakota Digital also offers a kit for newer models part MCL 3006 OT The kit includes the following gauges and features Speed programmable speed calibration performance menu two trip meters odometer count down service miles security and check engine lights Tachometer programmable tach clock gear position cruise indicator light high rom recall Oil Pressure programmable warning point uses stock sensor or Dakota Digital sensor for higher pressure Oil Temperature programmable warning point complete with new sensor Volts programmable warning point Fuel Level uses factory sensor low fuel warning can be programmed for custom fuel sender NOTE The factory ambient air temp gauge is replaced by an oil temperature gauge All gauges have automatic night dimming controlled by a sensor in the tachometer TV TT aun Lt wl MPH 0000ga E 1 MAN 650226 B INSTALLATION First read and familiarize yourself with all of the components and this manual The first step is to remove the seat and disconnect the negative side of the battery as with any electronic install Once the battery is disconnected you are ready to
14. Red 4 MAN 650226 B If you are using the cable driven adaptor you will also need to pull the speedometer cable from the front wheel and replace the cable nut with the supplied cable nut so your soeedometer cable will thread onto the new sender You have to take the cable off at the wheel so the nut can slide down and off the end of the cable and allow the new nut to Slide on After the nut has been replaced the soeedometer cable can be connected back to the wheel and also to the sender Secure the sender with a zip tie and make sure there is no binding in the cable and that the cable has engaged fully into the sender Speedometer and Tachometer connectors To connect the adapter box to the speedometer and tachometer you will need the supplied Y harness this may already be connected to the adapter box This harness has one 16 pin connector and two 10 pin connectors The adapter box will attach to the 16 pin connector The tachometer will attach to the 10 pin connector with a long orange wire hanging off it and will have a total of 8 wires The speedometer will attach to the 10 pin connector with 9 wires in it Clock Memory connection You will need to locate a fused constant 12V battery power wire for the orange clock memory wire The long orange clock memory wire is located on the tachometer gauge plug Check your service manual or use a voltmeter or test light to find and verify a constant power location One common location to pick up the
15. am gear indicator in setup see instructions Gauge will not dim Night dimming is turned off or too low Change night setting in setup see instructions Gauge remains dim at all Night dimming is turn too high Change night setting in setup See instructions times Light sensor at bottom of gauge is covered Make sure the lower part of the lens is not covered Cruise Engage indicator Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 12 volts does not work when the indicator should be off and about 0 volts when the indicator should be on 15 MAN 650226 C Small gauge Troubleshooting guide Problem Gauge will not light up Possible cause Orange wire does not have power Black wire is not getting a good ground Solution Connect to a location that has power check fuses Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge reading is erratic or Gauge signal wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on gauge engine and sensor Gauge reading is incorrect _ Gauge is set up for wrong sensor type Change sensor setting in setup See instructions Gauge will not dim Blue wire 2 pin harness is not connected Check wiring connections Blue wire should have 12 volts correctly when tachometer is dim Gaug
16. ble Hi warn 230F range 200 290F or 93 143C Lo Warn 10 not adjustable 10 MAN 650226 B SPEEDOMETER SETUP Main Menu Sub Menu Description GPd Auto select speed unit and auto calibrate speed AdduSt select speed unit and adjust calibrate speed 5 SEE miles to service setting PErF enable disable performance readings odao one time odometer preset only shown while odometer has less than 100 miles 1 Until the speedometer is calibrated the odometer display will show PLEASE SEE SPEEd This message can be cleared temporarily by pressing and holding the switch To enter the speedometer setup press and hold the switch while turning the key on and starting the engine Once the engine is running release the switch The speedometer will show Press and release the switch so that SF is displayed Press and hold the switch for about 3 seconds until is displayed Release the switch The MPH display will show SEE and the odometer display will show Auta Press and release the switch to move through the different menus press and hold the switch to select a menu option Note The speedometer calibration and gear programming are the only functions that require you to hold the switch while starting the bike and this is only if you are going to adjust the calibration since you will have to ride the bike Some ignition systems may disrupt power to other circuits causing the gauge to reset this is why you
17. by the customer within the first 100 miles Once the odometer has more than 100 miles the menu option will no longer be displayed Make sure you have first calibrated the soeedometer and correctly selected the units to be either MPH or km h first The odometer will be set in the selected units Once you have preset the miles you cannot change it again WARNING This only allows setting odometer to the nearest mile Do not use tenths For example a mileage of 65432 1 should be set to 65432 using this method If the tenths digit is used the odometer will read 10 times too high e Press and release the switch until odar is displayed then press and hold the switch until is displayed The current miles will be displayed with the left most digit flashing Press and release the switch to increment the digit Press and hold the switch to move to the next digit to the right Continue until the right most digit has been set Press and hold the switch and the speed display will show nao Press and hold the switch while nao is displayed to go back and continue changing the odometer display Turn the key off to cancel any changes e Press and release the switch to change to speed display to YES the current odometer reading Press and hold the switch while YES is displayed to save TACHOMETER SETUP Main Menu Sub Menu Description CL set clock time ECH n 9HE set night dimming level E CAL set engine cylinder setting uPd
18. connected properly Check connection from gray wire to speed signal wire will only show zero Speed sensor not grounded properly Move ground to different location preferable close to the speedometer ground Speed sensor is not being turned by Check cable connection between sensor and transmission transmission Sensor can be tested by spinning the cable with a drill Sensor is not sending a speed signal Check for a damaged or malfunctioning speed sensor Gauge is not calibrated Gauge must be recalibrated see instructions PLEASE SET SPEED Speedometer not calibrated Gauge must be calibrated to your vehicle see instructions Speed reading is erratic or Speed sensor wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Cable is loose or broken Check cable between sensor and transmission Poor ground connection Check ground connection on speedometer and sensor Ignition Interference Check for tachometer wires routed with VSS signal wires Check for VSS signal wires routed near ignition coils Check for poor ignition system ground Use suppression spark plug wires Speed reading is incorrect _ Gauge is not calibrated correctly Gauge must be calibrated see instructions Gauge will not dim Blue wire 2 pin harness is not connected Check wiring connections Blue wire should have 12 volts correctly when tachometer is dim Gauge remains dim at all Blue wire 2 wire harness is getting power all Check
19. e remains dim at all Blue wire 2 wire harness is getting power all Check wiring connections Blue wire should have 0 volts times all of the time when tachometer is bright Gauge will not enter setup Green wire 2 wire harness is not connected Check wiring connections Green wire should have 12 volts correctly when the switch is pressed WIRING COLOR CODE FOR SPEEDOMETER AND TACHOMETER Color on GAUGE WHITE RED WHITE BLACK GREEN WHITE GREEN accident Stock harness color varies with application BROWN VIOLET connects to supplied harness connects to supplied harness see VSS section WHITE GREEN BLACK YELLOW BLACK ORANGE WHITE RED ORANGE PINK GREEN RED Function speed sensor power out if required security system indicator switch input night dimming speed signal input output speed signal engine indicator ground for gauge 12 volt power with key on 12V battery power for clock tach signal input cruise set indicator To avoid damage to motorcycle please see Speedometer Tachometer and Status and Warning Indicators sections for details on locating VSS Tachometer and indicator wires for most motorcycle applications SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our products Please read through the Troubleshoo
20. e the meter is set to AC volts and not DC volts for this check Tachometer Troubleshooting guide Problem Possible cause Solution Gauge will not light up Red wire does not have power Connect to a location that has power Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Clock will not light up Orange wire does not have power Connect to a location that has constant power Clock will not keep time Orange wire does not have constant power Connect to a location that has constant power Gauge lights up but tach Yellow wire is not connected properly Check connection from yellow wire to tach signal wire will only show zero Ignition system not grounded properly Check engine and ignition system grounds Gauge is not grounded properly Check gauge and engine grounds Tach signal type is not set correctly Change the tach signal type see instructions Gauge is not calibrated Gauge must be recalibrated see instructions Tach reading is erratic or Tach signal wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on tachometer engine and ignition system Update rate is too fast Reset display update speed slower Tach reading is incorrect Gauge is not calibrated correctly Gauge must be calibrated see instructions Gear indicator is always Gears not programmed Progr
21. econds will reset the current display The display sequence is as follows SPEED MENU oogdog odometer mileage ppo trip meter mileage A g UUO O trip meter mileage B 5 ggg count down to service if programmed Eo Speedometer will show km h or MPH if metric PERFORMANCE MENU Hi Oa high speed recall 60 00 0 0 60mph time 0 100kph c5 00 0 quarter mile time c5 da quarter mile speed The 0 60 and 1 4 mile timers are zeroed by pressing and holding the switch while that timer is displayed The timer will not restart until the soeed reaches zero and then you start driving again The function switch can also be used to change the tachometer display Make sure the speedometer is displaying the odometer to avoid resetting any of the other settings before attempting to change the tachometer Press and hold the switch for about 4 seconds to change the tach menu Press and hold the switch for about 6 seconds to reset the high rom recall while it is displayed The tachometer only has two display modes as follows TACH MENU CLOCK gt fe dgd 12 hour clock HI RPM gt ud high rpm recall GAUGE SETUP AND CALIBRATION The function switch discussed above is used to enter setup mode for all of the gauges The first step in the setup procedure is to select which gauge you are going to select to change a setting Each gauge will either show a number or a label If the gauge is showing a label then that gauge will be selected to enter setup All of the
22. emp Voltmeter and Fuel Level Switch amp Dimming Sender WIRING plug in connections Now you are ready to make the gauge connections Included in the kit is an adaptor box that allows the kit to directly plug into the factory harness The box has several connections which are explained here The adapter box will lay inside the fairing behind the speed and tach The box can be secured to the wiring to prevent rattling SWITCH somo out E Plug into the back A onch pean roin ma jai gi First locate your speedometer and tachometer connectors in the factory wiring harness that where unplugged from the original speed and tach gauges Plug these connectors into their correct locations on the adaptor box The adapter box has one set of connectors for 1996 1999 applications and another set for 2000 2003 For cable driven speedometers you will also need to wire in a speed sensor If you have provisions for a transmission mounted sender use Dakota Digital SEN 1017 if not use Dakota Digital SEN 1011 a cable driven speed sensor Wiring of the speed sensor will be done using the supplied 3 wire pigtail that connects to the adaptor box The speed sensor pigtail should have a Red Black and White wires with a 3 pin connector The speed sensor will need to be connected to the pigtail following the table below Cut the red wire back if using the cable drive adaptor SEN 1011 since it is not used Pigtail SEN 1011 _ SEN 1017 Red
23. emperature gauge you will also want to install the oil temp sensor so the pin swapping can be performed and reached a little easier IMPORTANT NOTE SAVE ALL CLAMPS FROM THE FOUR SMALL GAUGES AS THEY WILL BE USED TO SECURE THE NEW DAKOTA DIGITAL GAUGES SAVE these clamps to secure new gauges Install New Gauges Note This step is only for those with out a factory switch or cable drive applications since the switch was mechanical and attached to the speedometer Now is a good time to install the function switch for cable drive applications it can be hard to mount once the gauges are installed Remove the rubber boot insert the switch from the back of the fairing and then tighten the rubber boot on from the front 3 MAN 650226 B Next you are ready to install the new gauges into the fairing The new speedometer and tachometer come supplied with new gaskets and clamps Install the gauges and secure using the supplied clamps and gasket on the speedometer and tachometer reusing the old clamps on the small gauges securing the clamps with the supplied nuts The picture on the first page shows the proper location for each gauge Be sure the alignment tab on the clamp lines up with the notches in the fairing Some fairings may only have one notch line up at least one tab on the clamp with the notch in the fairing this will insure the gauges are centered and aligned correctly D ignition Ground Speedometer and Tachometer Oil PSI Oil T
24. er reading gt Please see Speed sensor voltage checks on the last page for assistance in checking your sensor 11 MAN 650226 C Speedometer Setup Continued 5 SEt Miles to Next Service setup The service mileage is a countdown mile meter The service mile display can be disabled or can be set to count down from 500 7500 miles If the service mileage is enabled and it gets to 0 miles it will display S du each time the key is turned on If the push button switch is pressed and held while S XXXxX is displayed the service miles will be reset to your preset e Press and release the switch until S XXXX is displayed then press and hold the switch until is displayed e Release the switch The current setting will be displayed OFF or a mileage from 500 1500 e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed PE F Performance menu setup The performance readings can be turned on or off When they are turned off the odometer will only toggle through the mileage readings e Press and release the switch until PErF is displayed then press and hold the switch until is displayed e Release the switch The current setting will be displayed on or oF F e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed odo Odometer preset The odometer can be preset
25. ht it should be about flush with the end of the adaptor bushing see photos below 5 MAN 650226 B Oil temp sensor adaptor bushing and o ring EVO temp sender assembled Twin Cam Engines The supplied oil temperature sensor replaces one of the oil pan plugs in twin cam engines Oil Temp sensor and harness Now you are ready to install the sensor into the oil pan You can do this at an oil change so you do not have to worry about losing oil or if done quickly you should only lose a small amount of oil First locate the allen head plug on the front bottom side of the oil pan or the drain plug The plug for twin cams is on the left of the oil pan drain plug that is used to drain the engine oil for an oil change It is a 3 8 NPT allen head plug that should be flush with the oil pan See photo for the correct plug Wipe any road grime and oil from around the sensor so the area is clean Use a 5 16 allen wrench to remove the plug or a wrench for the drain plug on EVO applications Have the sensor ready to thread in so minimal oil is lost Tighten down the new oil temp sensor with a 3 4 wrench NOTE Check oil level after install of this sensor refill oil as needed 6 MAN 650226 B TEMP pare pe gt a I k Oil Drain Plug we a fe Roe Bottom of oil pan Remove 3 8 npt allen plug ae Tighten temp se nsor with a 3 4 wrench T E PA N t i i k gt ie ek
26. must hold the switch while starting if you are performing speedometer calibration All other gauge functions and gauges can be set without running the engine SPEED CALIBRATION There are two methods for calibrating the speedometer auto cal and adjust Either one can be used Auto cal requires that you have one measured mile marked out km for metric this is the best method to start with if your speedometer needs a lot of correction Adjust requires you to follow another vehicle going at a set speed time your self over a mile to determine your speed or use a hand held GPS with speed indication Auta Auto Cal e Press and release the switch until Auto is displayed then press and hold the switch until is displayed e Release the switch The display will switch to un it and light up the current speed unit MPH or km h e Press and hold the switch to keep the current unit or press and release the switch to change the unit e Next the speedometer will display CAL and the message display will show zeroes You should now begin driving the measured mile The message display will count the number of pulses received from the sensor The message display cannot be used to determine when a mile has been driven Once you reach the end of your marked mile press and release the switch again The calibration is now done AdduSt Adjust e Press and release the switch until AdUuSe is displayed then press and hold the switch until
27. ntil Ld is displayed then release the switch Press and release the switch until the desired low pressure warning point is displayed Press and hold the switch until H i is displayed then release the switch Press and release the switch until the desired high pressure warning point is displayed Press and hold the switch until SPd is displayed then release the switch Press and release the switch to change the update rate between fast F5t and slow SLU Press and hold until is displayed to save the settings Turn the key off OIL TEMPERATURE SETUP The oil temp gauge has a user selectable high temperature warning point that can be set so the gauge will flash the reading when the temp is met or exceeded The gauge will only read correctly with the supplied sender To enter setup press and hold the switch while turning the key on Release the switch The gauge will show Press and release the switch until F or is displayed then press and hold the switch until Sna is displayed Press and release the switch to change between Fahrenheit F and Celsius C Press and hold the switch until H i is displayed then release the switch Press and release the switch until the desired high temperature warning point is displayed Press and hold until is displayed to save the settings Turn the key off FUEL SETUP The fuel gauge can be set to read the two comm
28. on stock Harley sensors see setup procedure below for correct sender selection There is also a non adjustable warning feature that will flash the gauge at any reading below 10 as a low fuel warning indicator To enter setup press and hold the switch while turning the key on Release the switch The gauge will show Press and release the switch until FUL is displayed then press and hold the switch until Snrd is displayed Press and release the switch until the correct sender type is displayed 10 for 73 10 33 for 240 33 CUS for custom or LAL for custom sender programming The stock fuel sender should use the ID setting for correct readings If LAL is not selected press and hold until is displayed Turn the key off If LUIS is selected and a custom fuel curve has not yet been programmed the gauge will immediately enter the LAL routine If LAL is selected the fuel sender curve can be programmed into the gauge Begin with an empty tank The gauge will be showing 00 and switch to displaying the measured resistance Press and release the switch to save the empty reading The display will show 33 and then switch to displaying the measured resistance Add enough fuel to fill the tank to 1 3 Press and release the switch to save the 1 3 reading The display will show 66 and then switch to displaying the measured resistance Add more fuel to fill the tank to 2 3
29. range wire is powered To set the clock press and hold the switch while turning the key on Release the switch The RPM display should show LL press and hold switch until is displayed Release the switch The lower display will show the current hours Press and release the switch to change the hours press and hold the switch to change the minutes Release the switch The lower display will show the current minutes Press and release the switch to change the minutes press and hold the switch to save this and exit setup 12 MAN 650226 C Tachometer Setup Continued n I9HE NIGHT DIMMING e gt gt T Your display system has a dimming feature that dims the display intensity Normally the system is at full brightness for daytime viewing The tachometer has a light sensor that will provide a signal to the other gauges to reduce the brightness at night The level of darkness before the gauges dim can be adjusted in the tachometer setup Press and release the switch until n SHE is displayed then press and hold the switch until is displayed Release the switch The update setting will be displayed late darkest mid J early lightest OFF Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting CAL Engine cylinder setup Press and release the switch until t CAL is displayed
30. s tab While pushing on the tab pull the wire gently out from the back of the connector You will need to remove Black pin 2 gauge ground bottom center location in the housing Blue w Violet pin3 gauge signal old air temp sensor right location looking at back of housing Insert the RED wire into the previous location of the Blue w violet wire Insert the other BLACK wire with a short 3 pigtail into the black wire s previous location Slide supplied piece of heat shrink over the pigtail and connect the spade connector on the black wire to the original gauge ground wire that was removed from the housing This provides ground for the gauge and sensor Heat up the heat shrink to protect the ground connection NOTE See Photos on the following page for more details 8 MAN 650226 B T b A 1 3 p wd Using a small allen pick release the locking tab Push gently on the tab to release pin Y SAR CONNECT TO FACTORY BLACK WIRE we FOR GROUND SECURE THE g Le AIR TEMP AND BLACK WIRE ILLUMINATION _ FROM TEMP WIRES j p 4 SENSOR RED WIRE FROM TEMP SENSOR p A pen 4 D Hi i Pal d r E 9 MAN 650226 B FUNCTION SWITCH The push button function switch mounted beside the speedometer allows access to all of the mileage rom and performance information Pressing and releasing the function switch toggles through the different displays Pressing and holding the switch for about 2 s
31. then press and hold the switch until is displayed Release the switch The current cylinder setting will be displayed Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed uPdAtE Display update setup The display update will select how quickly the tachometer reading will respond Press and release the switch until ufdAreE is displayed then press and hold the switch until is displayed Release the switch The update setting will be displayed slow mid j fast Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting LJArn Rpm warning setup Press and release the switch until uJArn is displayed then press and hold the switch until is displayed Release the switch The current warning point will be displayed Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting SEAr Gear Indicator setup This tachometer has a single digit display for gear position The gauge can learn the positions based on speed and rom so no sensors are needed just what you ve already plugged in It will work with 4 5 6 or 7 speed transmissions To program the gear positions begin at a section of road where you can gradually shift through all of the gears Press and hold the switch
32. ting Guide There you will find the solution to most problems Should you ever need to send the unit back for repairs please call our technical support line 605 332 6513 to request a Return Merchandise Authorization number Package the product in a good quality box along with plenty of packing material Ship the product by UPS or insured Parcel Post Be sure to include the RMA number on the package and include a complete description of the problem with RMA number your full name and address street address preferred and a telephone number where you can be reached during the day Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase Send no money We will bill you after repair Dakota Digital 24 Month Warranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it under normal use and condition be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE such defect s will be repaired or replaced at Dakota Digital s option This warranty does not cover nor extend to damage to the vehicle s systems and does not cover removal or reinstallation of the product This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or This Warranty is in lieu of all other expressed warranties or liabilities Any implied warranties
Download Pdf Manuals
Related Search