MOGS – 100 Installation, Operation and Maintenance Manual
Contents
1. MOGS 100 Installation Operation and Maintenance Manual MOGS 100 WWW OGSI COM Oxygen Generating Systems Intl OGS 814 Wurlitzer Drive North Tonawanda New York 14120 USA Tel 716 564 5165 Toll Free 800 414 6474 Fax 716 564 5173 E mail ogsimail ogsi com Website www ogsi com Part 9000000 004 US 25 00 Effective 11 2010 Table of Contents Topic Page Number Using this Manual 1 Initial Inspection 2 Warranty Information and Liabilities 3 Safety Guidelines 5 6 gt Handling gt Operating 6 Product Information 7 22 gt Features and Applications gt PSA Technology gt Components 10 gt Process Flow Description 21 gt Specifications 22 Safety Precautions 23 Pre Installation 24 Required Operating Conditions 25 Set up and Installation 26 Operating Instructions 27 Troubleshooting Guide 28 Touch Screen Overview 30 Manifold Design and Installation 44 Cylinder Filling Procedure 46 Preventive Maintenance 49 Technical Service Assistance 51 Appendix I VII gt Spare Parts List I gt Oxygen Cleaning Procedure I gt Oxygen Sensor Calibration Procedure IV gt Air Changes by Room Size V gt Units of Measurement VI gt Maintenance Log VII Effective 11 2010 Rev A 2010 OGSI All rights reserved OGST is a registered trademark This publication may not be reproduced in part or whole without written permission of OGST Password to Access Touch Sc2. This equates to approximately 4 6 kW of power It is required that a 30 A circuit be dedicated to each MOGS 100 unit Additionally the unit must be plugged into this circuit using only the supplied power cord and without additional extension cords Do NOT run at 208 VAC Positioning The unit must be operated in an upright position only with no obstruction blocking airflow around the unit Effective 11 2010 25 Set up amp Installation Although every MOGS 100 unit is thoroughly tested and checked before it is shipped from our facility the following checks are necessary to ensure that none of the internal components have been damaged in shipment This check should take less than five minutes to perform Refer to Initial Inspection on Page 2 before reading the instructions below Make a visual inspection of the interior and exterior of the machine Ensure that all parts are properly attached and that there is no obvious damage including external manifold if applicable Connect the unit to an electrical panel of 230 VAC with a 30 A circuit breaker Ensure that the touch screen is powered and a display is visible Consult the troubleshooting guide in this manual See Page 28 for any problems encountered After entering a password and selecting a language start the machine by pressing both the Operating Mode AUTOMATIC and then the ON OFF buttons oR Listen for the sound of the compressors and
3. 28 A Warning Signs Thermal Switch Warning The appropriate thermal overload switch must be reset by pressing it and the CLEAR WARNING button must be pressed Normal operation can then be resumed Low Oxygen Pressure This may be a result of a leak in the system Use a leak testing solution to locate and repair any leaks The machine has run for 30 minutes and purity has not yet been reached This may be a result of a leak in the system Use a leak testing solution to locate and repair any leaks Oxygen purity has fallen below acceptable limits This may be an indication of a leak within the system Use a leak testing solution to locate and repair any leaks No power screen Touch screen has lost its program PLC Communication timeout PLC has lost its program The cable has come loose The system is not running in the appropriate mode Effective 11 2010 29 Touch Screen Overview The touch screen is the main interface between the operator and machine and incorporates all controlling mechanisms within its display Listed below are the Main Operator Features incorporated within the touch screen Language selection Password protection Energize de energize the machine Monitor the operating condition of valves and compressors Monitor all system pressures and oxygen purity Hours meter and real time clock to monitor service intervals Line graphs meter readi
4. 80 89 a leak may have developed in the machine While the system is still running and pressurized a small amount of soapy water can be used to try to find the leaking part If the purity is very low the sieve beds may need to be replaced They are designed to be able to be replaced quickly and easily in the field If you do not have a replacement set of beds in your stock contact the factory or your local distributor Effective 11 2010 42 Correcting Missing or Irregular Touch Screen Color Scheme e Ensure that the machine is not in CYCLING mode and leave the machine in the ON position e Touch both the top left corner and the bottom left corner of the touch screen at the same time Press both corners at the same time e Select the appropriate language English or Spanish e Select DISPLAY TEST The screen will display all the colors continuously allowing the user to see if a color is not displayed correctly Select EXIT at any time to go back to the previous screen e Select TOUCHPAD TEST The screen will display a grid The user can select each square in the grid to ensure that all sections of the screen are responding Select EXIT to return to the main menu e Select EXIT when done to return to the screen displayed before the two corners were pressed Effective 11 2010 43 YSaNIIAD 3ZIS Lu N MOGS 100 Filling Manifold Design amp Installation Optional f N e dvI9 AWWAs F3AO
5. Blank touch screen display e Circuit breaker has tripped e Loose wires e Ensure that power is available from 230 VAC supply e Check the Emergency Stop button If this button is pushed in it secures all power to the system e Visually inspect the electrical wiring Reconnect any loose wires to the labeled location System failure No sound e System is in MANUAL mode e Low pressure e Press the additional START button if system is in manual mode e Check the GAUGE screen and ensure that the current High Oxygen Pressure is not greater than the set Low point e Check the ALARM screen for any faults A WARNING ACTIVE sign will appear at the bottom of each screen if a fault has occurred System shuts down inadvertently WARNING ACTIVE indication Extreme change in oxygen pressure e Check the ALARM screen If a warning is active follow the instructions e Check the high oxygen pressure gauge If the reading is equal to the set point the machine has been programmed to shut down Valves Sticking Pressure levels too high Dusting of sieve or machine filled with dirt and dust due to filters not being replaced Remove valve block from machine and clean valves and spools completely Pressure Transducer not Working Machine not shutting ON OFF at target pressures Faulty transducer Remove transducer and return for replacement Effective 11 2010
6. and need to be changed twice a year in normal environments to maintain system performance In areas of excessive dust and oil it is important to change the filters more often A quarterly change is recommended These filter elements are accessed by removing the wing nuts on the black filter housing covers at eye level inside the front door These can also be supplied by OGST as part of a spares kit Cabinet The cabinet should be occasionally washed down with a sponge or clean rag and some soapy water Avoid the use of ammonia or other strong chemical based cleaning solvents The intention is to avoid dust and dirt from building up on the machine Ammonia in particular will contaminate the molecular sieve inside the oxygen generators and result in poor unit performance Air Storage Tank Drain When the system is first installed it is a good idea to open the solenoid valve drain located at the bottom of the grey air tank every few days If more than a few drops of water are drained from the tank it implies that your location is very humid and you should check the storage tank regularly every few days If there is very little or no water drainage then the storage tank can be checked less frequently once every month The idea is to prevent water from getting into the oxygen generator sieve beds This is not needed for units with an auto drain Air Compressors The Air Compressors should last four 4 to five 5 years or longer under no
7. call Effective 11 2010 50 Technical Service Assistance It is our intention to provide complete customer satisfaction This manual is one way in which we hope to provide you with technical assistance If you do not find what you need in this manual or you have other questions about this equipment please feel free to contact us directly We look forward to serving your oxygen needs and invite your inquiries We will respond to you as promptly as possible You can reach OGSI through the following means e By Telephone Within the United States and Canada 800 414 6474 Our toll free number Within USA and Canada only 716 564 5165 Our direct number e By Telephone Outside the United States Your local International Access Code usually 0 or 00 followed by The Country Code for the U S which is 1 followed by Our Area Code and Number 716 564 5165 e By Automated Voicemail 716 564 5165 e By Fax Within or outside the United States 716 564 5173 e By E Mail or Website ogsimail ogsi com http www ogsi com e By Mail OGSI 814 Wurlitzer Drive North Tonawanda New York 14120 USA e By UPS FedEx or Common Carrier Address to return shipments OGSI 814 Wurlitzer Drive North Tonawanda New York 14120 USA Technical service personnel are available from 8 00 AM to 5 00 PM EST GMT 5 We also have a list of Distributors and Authorized Service Agents available upon request Customer Sat
8. cooling fan to start running if you do not hear them within a few seconds shut the machine down immediately by pressing the ON OFF button and call OGST for assistance Once the machine is running press the MAIN MENU button then press GAUGES to view the GAUGE screen Both the regulated air and low oxygen pressure gauge needle indicators should be operating within the highlighted green area The Oxygen Purity Gauge should steadily increase to above 90 The oxygen storage tank pressure gauge should indicate a pressure increase after approximately 15 minutes If this does not occur check to make sure that none of the hose connections have come loose Call OGSI Technical Service Department at 800 414 6474 toll free number in USA and Canada or 716 564 5165 if no loose connections are found and trouble persists Effective 11 2010 26 Operating Instructions Start up Once the system has been installed in accordance with the set up and installation instructions it may be energized and cylinder filling may begin It is highly recommended that the user read the Touch Screen Overview section Pages 30 43 prior to operating the system On the MAIN MENU screen press the CONTROL button Choose between AUTOMATIC and MANUAL modes of operation For a detailed explanation of modes and all other touch screen functions see the Touch Screen Overview section Pages 30 43 If selected the AUTOMATIC mode will
9. ogsi com email ogsimail ogsi com OXYGEN PURITY SOFTWARE VERSIONS 93 HG Ou PRI MOGS1 0U5 EZP DATE OF COMPLETION e 87 2616 UPGRADED Main Menu This screen displays information pertinent to the system and manufacturer contact information The Model Number of the Machine and its Serial Number are displayed along with the Date of Completion The software versions for both the Programmable Controller and Touch Screen are also shown During the course of normal maintenance the company may offer to upgrade the software packages on the machine as improvements and modifications to it become available Effective 11 2010 41 Troubleshooting Screen OGSI MODEL MOGS 168 BED TROUBLESHOOT SCREEN The TROUBLESHOOTING screen was designed to test each set of sieve beds individually to see if one is out of purity in the system It is important to note that once you enter this troubleshooting mode the system will not continue to operate normally Once the troubleshooting has been completed the system can be re started again To begin the troubleshooting you need to push the button under the sieve bed set you want to start up and then push the ON OFF button This will only activate that set of sieve beds Then after 15 minutes of running you will see on the Oxygen Purity Gauge if that sieve bed set is not running properly making at least 90 pure oxygen In some cases especially if the reading is only slightly low
10. setting The enclosure meets NEMA 12 protection guidelines which provides a degree of protection against dust falling dirt and non corrosive liquids Feed Air Ambient Air Quality The life of any PSA MOGS 100 unit is directly related to the air quality that is fed into it Hot humid dirty oily air deteriorates and degrades the performance of the molecular sieve In order to preserve the effectiveness and extend the life of the generator precautions must be taken to ensure that the air provided is cool dry clean and oil free Changing the inlet air filter is a simple and easy way to provide the unit with some protection It is advisable to set up the unit in an air conditioned or a well ventilated area The room should also be free of toxic gases and high concentrations of hydrocarbons especially carbon monoxide Humid oily areas should be avoided as installation sites as much as possible Ambient Air Temperature The machine is designed for use over a temperature range of 40 F to 100 F 5 C to 38 C Since hot air has the ability to hold more water in the form of humidity than cool air operating the units in hot areas will reduce the effective life of the molecular sieve Note Operation outside of this temperature range will not be warranted by OGSI Electrical Power On U S models the power for the control circuitry of the MOGS 100 unit is a single phase electrical supply of 230 VAC and about 20 A at a frequency of 60 Hz
11. status can also be viewed here gt Power In AUTOMATIC mode the machine will start running when the button is in the ON position In MANUAL mode this button must be in the ON position and also requires the additional START button to be pressed When pressed again this button will stop the machine regardless of the mode of operation gt Operating Mode This feature allows the selection of either MANUAL or AUTOMATIC modes The AUTOMATIC mode will initiate machine operation when the ON OFF button is in the ON position and all other conditions are satisfied The MANUAL mode requires an additional START button to be pressed and is intended to prevent inadvertent machine operation gt Manual Start This feature is used in conjunction with the MANUAL mode of operation and must be pressed each time the system is started gt System Status This feature monitors the current status of the system It will display STANDBY when the system is deactivated and CYCLING when the system is activated Effective 11 2010 34 gt Air Compressor This feature monitors the operational condition of the air compressors When the air compressors are de energized it will display STANDBY and will toggle to RUNNING when they are energized gt Oxygen Compressor This feature monitors the operational condition of the oxygen booster compressor When the oxygen compressor is de energized the feature will display STANDBY and will toggle
12. 010 IV Air Changes by Room Size Machine Size Air Changes Required in a Room Per Hour for All Models Model Number Room Volume in Cubic Feet ft 062 AEAEE OG 100 Z OG 175 Z OG 250 OG 375 OG 500 OG 650 OG 750 OG 1000 OG 1250 OG 1500 CFP 15 15M EE ESESESES Notes 1 NR means that the models indicated are not recommended for rooms of this size 2 For air changes requirements for models OG 2000 and above please contact OGSI Effective 11 2010 Vv Units of Measurement Ib U S Pound hp Horsepower psi Pound force per Square Inch kW Kilowatt kWh Kilowatt hour ft Cubic Feet VAC Volts Alternating Current Hz Hertz SCFH Standard Cubic Foot per Hour SCFM Standard Cubic Foot per Minute LPM Liter Per Minute 1 bar 1 45 x 10 psi dBA Decibel A scale A Ampere W Watt C Degree Celsius Centigrade F Degree Fahrenheit um Micrometer or Microns ppm Parts Per Million Effective 11 2010 VI 40 OGSI Maintenance Log Date Part Reason for Maintenance Authorized Service Technician Signature Effective 11 2010 vil
13. 11 2010 17 Fill Blast Containment Chamber MOGS 100 Fill Whip 1 Fill Chamber 1 Fill Whip 2 Fill Chamber 2 Effective 11 2010 18 Internal Components Description Power Distribution Panel The terminal board distributes electrical power to the different components of the system The air filter keeps dust and dirt from entering the compressor and needs to be changed twice a year in normal environments to maintain the unit s mietin u performance It should be changed more often in dirty oily areas Four 4 times a year is recommended The PLC Programmable Logic Controller processes inputs and outputs to and PLC from system components and communicates with the touch screen This is the brain of the machine Back Pressure Regulator Gauge This gauge controls the balance between oxygen flow and oxygen purity Initial setting is between 45 psi 3 1 bar and 50 psi 3 4 bar A higher back pressure will increase purity but decrease storage tank pressure A lower back pressure will increase storage tank pressure but decrease purity This regulator will adjust the storage pressure and oxygen purity Air Storage Tank Air from the air compressors is stored in this tank before going through the sieve bed sets on the side of the machine Normally this tank pressure holds between 23 psi 1 6 bar and 26 psi 1 8 bar Air Compressor The air compressors supply the
14. 3 m that room should be well ventilated at least 5 air changes in the room per hour The oxygen generator will be discharging nitrogen into the atmosphere of the room and a nitrogen build up could be dangerous to people entering the room If the generator is placed in a small closet the air in that closet will become enriched with nitrogen As the oxygen generator continues to operate it would become more and more difficult for it to separate the oxygen from the air because oxygen will make up a smaller and smaller fraction of the air that is fed into the oxygen generator 3 Power Supply for the MOGS 100 The oxygen generator should be positioned within 8 ft 2 2 m of the electrical outlet that will power it The MOGS 100 is a stationary unit and should not be powered by extension cords exposed to wear The electrical outlet system to which the OGSI oxygen generator is connected should be used exclusively for that purpose and no other electrical appliances should be connected to it It is recommended that you use a disconnect lockout panel on the MOGS 100 inlet power source to make it easier to service the machine The MOGS 100 unit will run on 230 VAC single phase power 50 60 Hz Do NOT run at 208 VAC this will damage components in the machine and void your warranty Effective 11 2010 24 Required Operating Conditions Location of Machine The MOGS 100 unit is intended for use indoors in a commercial or light industrial
15. GS 100 unit is factory leak checked to insure trouble free operation If any external storage tanks or manifolds are installed every installed fitting and connection needs to be checked for leaks Failure to ensure that there are no leaks in the system can cause the system to run excessively due to wasted oxygen This in turn will cause premature wear on your machine Reserve Cylinders and Certification The system is shipped with a reserve bank of two 2 H K sized 244 ft capacity steel cylinders rated at 2200 psi 152 bar These are located on the back side of the control panel and are used to trans fill smaller D E or M size cylinders in the blast containment chamber These cylinders come fully connected and leak checked and do not have to be removed or serviced until they need to be re certified Department of Transportation DOT recertification is required every five or ten years depending on the previous certification The date of last certification is stamped on the collar of the cylinder month and year only If a star symbol is stamped next to the date re certification is not required for ten 10 years If there is no star symbol then the cylinder must be re certified after five 5 years These cylinders have an industry standard CGA 540 valve at the top These valves are normally open but can be closed by turning them fully clockwise Auxiliary External Oxygen Ports On the left side of the MOGS 100 cabinet as you face the Con
16. I has no legal claim to make against any shipping company for damage At OGSI we are committed to using shipping companies with good reputations for taking care in the handling of freight and providing service in the event of damage Effective 11 2010 2 Warranty Oxygen Generating Systems Intl being a division of Audubon Machinery Corporation hereinafter OGSJ provides a warranty on its products the Products against defects in material and workmanship under normal use and operation to the extent set forth in this Warranty THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OF OGSI WITH RESPECT TO THE PRODUCTS AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED ALL OF WHICH ARE HEREBY DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW WITHOUT LIMITING THE GENERALITY OF THE FOREGOING DISCLAIMER AND EXCEPT AS OTHERWISE SET FORTH IN THIS WARRANTY OGSI DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY WITH RESPECT TO THE PRODUCTS AND ALL WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE THE WARRANTY OF OGSI AS SET FORTH HEREIN IS FOR THE BENEFIT OF THE ORIGINAL USER OF THE PRODUCTS AND IS NOT TRANSFERABLE WITHOUT THE PRIOR EXPRESS WRITTEN CONSENT OF OGST The OGSI Warranty provides the following 1 OGST shall repair or replace the Products free of charge to the original user where defects in the material and or workmanship are evident at the time of delivery Such replacement of the Products does not include dam
17. The warranty on parts or equipment manufactured by third parties and included as part of the Products e g air dryers air compressors oxygen compressors instrumentation etc is limited to the respective original warranties of such third parties Note A Return Authorization Number must be obtained from OGST prior to the return shipment of the Product or any component parts or equipment of the Products Effective 11 2010 3 The Return Authorization Number must be visibly written on the outside of the package of the returned Products component parts or equipment as applicable or OGST will not accept the return Note A Credit Certificate will be created for all Warranty Exchange transactions OGSI will provide the Credit Certificate with an invoice at the time of shipment to the original user The Credit Certificate must be included in the package to OGST with the returned products within 30 days of the date of the invoice Failure to return Warranty Exchange Products to OGST within 30 days will make the Warranty Exchange process void and payment for Products will be billed and due on receipt Note The warranties of OGSI as set forth herein shall also become null void and not binding on OGST if a defect or malfunction occurs in the Products or any part of the Products as a result of a A failure to provide the Required Operating Conditions for the Products See Page 25 b Repair attempted repair adjustment or servicing
18. WIA NDILVITIddV OL SA3UNI1AI 3Z1IS oe aaan aNI LON GIOSINVW N39AXD OL 3SOH ANY 3ATVARK e X3ANITAI T X30N1743 d Red Se JJNSSJ d INIWOINI P anv 4 1 J9NVO A 3418 A D d A ans NU du FIN S3A0WSaD 1S0 NO 3JA 1VAZaDLVINDSS OL 44 Effective 11 2010 Design The MOGS 100 oxygen generating system manifold serves two purposes e To connect the MOGS 100 to each bottle for filling e To connect the bottles to one another for equalizing during trans filling filling smaller bottles from larger ones A shut off valve is located at the end of the manifold downstream of the K type storage cylinders This valve stops the flow of oxygen when a small cylinder is not attached in the filling station and also allows the user to fill the storage cylinders Every oxygen cylinder is equipped with its own shutoff valve so any additional valves in the system are unnecessary It is recommended that the filling manifold be as simple as possible with few valves and fittings in order to keep the number of potential leak points to a minimum Preferred materials for use in high pressure oxygen generation include but are not limited to e Stainless Steel e Brass e Bronze Installation When building and installing a cylinder filling manifold it is necessary to ensure that the threads on all NPT connections and all stainless steel on stainless steel connections are lubricated by Teflon ta
19. afety Guidelines Handling of Compressed Gas Cylinders Many of the following procedures for the handling storage and utilization of compressed gas in cylinders are taken from material furnished by the Compressed Gas Association which complies with OSHA standards Always ensure that compressed gas cylinders are securely strapped or chained in place to prevent tipping or falling Do not store near elevators stairs or passageways gt E Do not place cylinders in a position where they might become part of an electric circuit When electric welding is taking place precautions should be taken to prevent accidental grounding of cylinders permitting them to be burned by electric welding arc If visual inspection indicates obvious damage the cylinder should be returned to the supplier without any attempt at using the machine If cylinder leaks other than normal venting and the leak cannot be corrected by tightening a valve gland or packing nut the valve should be closed and a tag attached stating that the cylinder is not serviceable Remove the cylinder outdoors to a well ventilated or open area notify the supplier and follow the supplier s instructions for the return of the cylinder Keep the cylinder valve closed at all times except when in active use When removable caps are provided for valve protection they should not be removed except for active use Remember to replace removable caps when not in use Cylinder
20. ages incurred in shipping the Products If shipping damage is evident the original user should contact the shipper immediately OGSJ will pay for shipping the Products to the original user as well as returning damaged defective Products to OGSI Once the Products are repaired OGSI will ship the Products back to the original user and cover all costs incurred in shipping 2 OGST shall repair or replace the Products excluding filter elements and sieve material free of charge to the original user where defects in material and or workmanship become evident between the time of delivery to the original user and one 1 year from the date of delivery to the original user OGSI will pay for shipping the Products to the original user as well as returning damaged defective Products to OGSI Once the Products are repaired OGSJ will ship the Products back to the original user and cover all costs incurred in shipping In no event shall OGST have any responsibility or liability for the cost of labor for the removal of component parts or equipment that constitute part of the Products packaging of the component parts or equipment that constitute part of the Products or the re installation or replacement of the component parts or equipment that constitute part of the Products 3 The warranty provided by OGST to the original user covers parts and equipment specifically manufactured by OGSI and used as components or equipment that constitute part of the Products
21. ain maximum purity after initial start up or extended shut down Physical Air Inlet Filtration Level 0 3 um Oxygen Outlet Fitting LAT FNPT Bulkhead Sound Levels Door Closed 65dBA 1m Dimensions 34x 70x 72 in Wx Dx H 86 x 178 x 183 cm W x Dx H Weight 2550 Ib 1157 kg Power Requirement 230 VAC 50 60 Hz Single Phase 30 A Do NOT run at 208 VAC Operating Temperature Range 40 F to 100 F 5 C to 38 C Effective 11 2010 22 gt E gt Safety Precautions It is very important that you read the precautions below and make yourself aware of the hazards of oxygen in general While it can be handled and used very safely it can also be mishandled or applied incorrectly causing dangerous situations Oxygen is a fire hazard It can be very dangerous as it vigorously accelerates the burning of combustible materials To avoid fire and or the possibilities of an explosion oil grease or any other easily combustible materials must not be used on or near the MOGS 100 unit DO NOT SMOKE NEAR THE UNIT The unit should be kept away from heat and flames Individuals who have experience handling oxygen systems should become the designated operators of the MOGS 100 unit within your facility In critical applications it is important to have a backup supply of oxygen since the generator does not come with any reserve storage tank and requires electrical power to oper
22. arnings when any of the following faults occur gt 30 Minute Warning Air compressors have been running 30 minutes and the purity has not yet reached an acceptable level This could occur for a number of reasons A leak in the machine is chief among them If this occurs the TROUBLESHOOTING screen See Page 42 can be used to test each of the five oxygen generators individually to find the source of the problem Low Bed Pressure This may be a result of a leak in the system Use a leak testing solution to locate and repair any air leaks If this occurs the WARNING TROUBLESHOOTING Screen See Page 42 can be used to test each of the five oxygen generators individually to find the source of the problem It could also result from a problem with one or more of the air compressors Check to see that they are all running Effective 11 2010 39 gt High Air Pressure This warning is usually indicative of a contamination of the molecular sieve inside one or more of the oxygen generators Warning Contact OGST if this warning occurs These warnings must be cleared after following the instructions on the displayed warning indicator For certain alarms the machine will not operate until the CLEAR WARNING button has been pressed Effective 11 2010 40 Information Screen For any problems with this system contact OGSI at 888 414 6474 or Fax 716 564 5173 or Tel 716 564 5165 or visit our website wuu
23. ate Therefore during power outages oxygen will not be produced Do not use extension cords to bring power to the generator It is also important to use only a properly grounded outlet High pressure oxygen may present a hazard Always follow proper operating procedures and open valves slowly Rapid pressurization may result in personal injury Safety glasses and hearing protection are required when venting oxygen under high pressure Ensure that the oxygen outlet stream is not directed toward anyone s clothing Oxygen will embed itself in the material and one spark or hot ash from a cigarette could violently ignite the clothing Effective 11 2010 23 Pre Installation Before installing the OGST MOGS 100 unit it is necessary to consider the location space available and power supply for the generator 1 Locating the MOGS 100 The oxygen generator should be located in an area that is indoors and remains between 40 F 5 C and 100 F 38 C Setting up the machine outdoors or in an area that is not normally within this temperature range will void the OGSI Warranty There should also be a distance of at least 8 20 cm between the unit and any side wall in the room that it will be located in This is to ensure that airflow into the machine through the cooling fans is not restricted 2 Space Available for the MOGS 100 If the MOGS 100 unit is going to be set up in a room that is small less than 1000 ft or 28
24. atmosphere the nitrogen it adsorbed under very low pressure through a waste gas muffler As the air enters the bed the nitrogen is adsorbed by the sieve and the oxygen passes through as product gas The oxygen is then drawn through an oxygen booster which pressurizes the product oxygen to a pressure of 70 90 psi 4 8 6 2 bar and sends it to the green oxygen storage tank This oxygen storage tank serves as a reservoir for the oxygen prior to entering the high pressure oxygen compressor The oxygen product gas is then delivered to the high pressure oxygen compressor where it is compressed up to 2200 psi 152 bar Oxygen is then delivered through a high pressure line either to the reserve cylinder bank for trans filling to smaller cylinders at a later time or sent directly to a small cylinder that is filled inside the blast containment chamber Once the system senses that the cylinders are full it will automatically stop until new cylinders are connected for refilling Effective 11 2010 21 Unit Specifications Performance Oxygen Volume 0 100 SCFH 3 Nm h 0 47 LPM Oxygen Pressure High Pressure Up to 2200 psi 152 bar Low Pressure Up to 70 psi 4 8 bar Oxygen Purity Oxygen Concentration United States Pharmacopeia USP XXII oxygen 93 Monograph 93 3 CO Output lt 300 ppm CO Output lt 10 ppm Oxygen Dew Point 100 F 73 C Response Time Approximately 5 minutes to att
25. cylinders are available from OGSI See drawing below for suggested layout High Pressure Effective 11 2010 47 Attaching and Filling Additional H K size Cylinders Start by fixing the Auxiliary Cylinder Filling Manifold to a wall or other stable structure near the MOGS machine Then connect the manifold to the Lower Auxiliary Oxygen port on the left side of the MOGS unit using the high pressure interconnecting line provided by OGST or your manifold supplier Make sure the cylinder valves on the two 2 reserve cylinders already connected are closed and that the manifold line is de pressurized when you begin to make use of this connection Next with all valves initially closed connect the steel braided pigtail connection whip between a manifold valve and a cylinder valve and tighten both connections using a 1 g wrench These are all CGA 540 Valve adapters Slowly open the cylinder valve and then the manifold valve Fully open both valves backing off turn to prevent the valve from sticking in the open position and appearing closed At this point the gauge on the top of the manifold will read the pressure contained within the cylinder Cylinder filling can be initiated by starting the machine See Start up Procedures on Page 27 It is also recommended by OGST that these external cylinders be wall mounted or secured in a cart to make sure they are not bumped over or accidentally tipped If they fall over and the valve breaks
26. d purity Main Menu The GAUGE screen displays the instantaneous reading of the four primary variables during system operation These are described below gt Oxygen Purity This feature displays the percentage of oxygen present which is typically about 93 43 The system will shut down automatically if low oxygen purity less than 90 is produced for more than a short period oftime and an alarm will be activated gt Bed Output Pressure This feature displays the oxygen pressure after entering the oxygen generator sieve beds typically in a range of 4 10 psi 0 3 0 7 bar gt Air Tank Pressure This feature displays the pressure associated with the air storage pressure tank typically between 24 26 psi 1 7 1 9 bar gt Oxygen Tank Pressure This feature displays the oxygen pressure existing in the oxygen storage pressure tank entering the oxygen compressor typically 0 90 psi 0 6 2 bar Note that if the oxygen tank is full has 70 90 psi i e 4 8 6 2 bar the machine will not run to produce oxygen Once the pressure falls below 70 psi 4 8 bar the system can be started manually or will turn on automatically depending on the mode of operation it is in Effective 11 2010 37 Graph Screen nDonzmN 44 54 64 24 34 TIME lt MIN gt AIR_TANK PRESS BED 02 PRESS 02 TANK PRESS PRESSURE GRAPH This screen shows the graph based on the readings on the GAUGE scree
27. e This is a complex machine and comes with its own Service Manual In AUTO mode it will turn on at about 1900 psi 131 bar and turn off at 2200 psi 152 bar Heat Exchanger The heat exchanger cooling fan is used to draw air into the unit and to remove heat from inside the enclosure It also cools the compressed air before it is delivered to the air storage tank The fan operates while the unit runs Oxygen Storage Tank The storage tank serves as a reservoir for the oxygen prior to entering the oxygen compressor The tank is painted green to represent oxygen as opposed to the grey color of the air tank The generator will run according to the pressure in this tank ON at 70 psi 4 8 bar OFF at 90 psi 6 2 bar With the oxygen at this pressure it can be delivered to the high pressure oxygen compressor or be sent directly out of the machine through the lower auxiliary oxygen port Pressure will usually drop to about 30 psi when the oxygen compressor is running Oxygen Booster The oxygen booster increases the oxygen pressure prior to it being delivered to the oxygen storage tank Fill Whip Chamber 1 This whip allows oxygen to flow to the small cylinder being filled in Chamber 1 It has a CGA 870 Valve at the end of it Fill Whip Chamber 2 This whip allows oxygen to flow to the small cylinder being filled in Chamber 2 It has a CGA 870 Valve on the end of it Fill Chamber 1 This is the left side b
28. ers Nursing Homes Effective 11 2010 0 gem Pressure Swing Adsorption PSA Technology 2 An OGSI Oxygen Generator is an on site oxygen generating machine capable of producing oxygen on demand in accordance with your requirements In effect it separates the oxygen 21 from the air it is provided and returns the nitrogen 78 to the atmosphere through a waste gas muffler The separation process employs a technology called Pressure Swing Adsorption PSA At the heart of this technology is a material called Molecular Sieve Zeolite This sieve is an inert ceramic like material that is designed to adsorb nitrogen more readily than oxygen Each of the two beds that make up the generator contains this sieve The process is described below Stage 1 Compressed air is fed into the first molecular sieve bed Nitrogen is trapped while oxygen is allowed to flow through Stage 3 As the second bed separates the oxygen from the nitrogen the first bed vents its nitrogen into the atmosphere Stage 2 When the sieve in the first bed becomes full of nitrogen the airflow is then directed into the second bed Stage 4 Compressed air is once again fed into the first bed and the process is repeated continuously A constant flow of oxygen is produced This air separation process is reliable and virtually maintenance free The molecular sieve will last indefinitely as long as it does not beco
29. event of an emergency This button should not be used to turn off the equipment under normal conditions Valve Fill Chamber 1 This valve controls oxygen flow to the small cylinder being filled in Chamber 1 when open Valve Fill Chamber 2 This valve allows oxygen to flow to the small cylinder being filled in Chamber 2 when open Gauge Fill Chamber 1 This gauge displays the oxygen pressure in the small cylinder being filled in Chamber 1 Gauge Fill Chamber 2 This gauge displays the oxygen pressure in the small cylinder being filled in Chamber 2 Touch Screen The touch screen is the main user interface for the machine All controls are programmed within the touch screen Effective 11 2010 15 mmh o_ a O oON e o PF WD Internal Components Front View Tom ATL 2 LaL 08 gt f Muyu gt uu F iy 10 11 Power Distribution Panel Inlet Air Filters Programmable Logic Controller PLC Back Pressure Regulator Gauge Air Storage Tank Air Compressors Bank 5 Air Pressure Transducer Oxygen Generator Bank 5 Low Oxygen Pressure Transducer Oxygen Purity Sensor Oxygen Compressor Effective 11 2010 16 Rear View AN 5 domnick hunter 1 Heat Exchanger 2 Compressed Air Filter 3 Back Pressure Regulator 4 Oxygen Storage Tank 5 Refrigerant Dryer Effective
30. feed air for the sieve beds They are held in place by four bolted rubber mounts and can be easily replaced when necessary They should work as designed for a minimum of 10 000 hours and will last 20 000 hours in many cases Air Pressure Transducer The transducer gives a variable output current to the PLC at different pressures The PLC then communicates this signal to a virtual gauge in the touch screen Oxygen Generators These generators contain the molecular sieve that performs the air separation process Exposing the internal sieve material to the atmosphere will cause contamination However if the sieve becomes contaminated the beds can be easily replaced Low Oxygen Pressure Transducer The transducer gives a variable output current to the PLC at different pressures The PLC then communicates this signal to a virtual gauge in the touch screen Oxygen Purity Sensor The oxygen sensor gives a variable output current to the PLC at different levels of oxygen purity The PLC then communicates this signal to a virtual gauge in the touch screen See Appendix Page IV for details on how to make an adjustment to this sensor Effective 11 2010 19 Oxygen Compressor The RIX oxygen compressor boosts the oxygen pressure from the oxygen storage tank to 2200 psi 152 bar It is a two stage compressor with a self contained motor starting capacitor pressure switch pressure relief valve and check valv
31. fold can be connected increasing the size of the reserve bank by 3 4 etc additional cylinders These additional high pressure reserve manifolds along with extra cylinders are available from OGST Reserve Cylinder Bank The system is shipped with a reserve bank of two 2 H K size 244 ft capacity steel cylinders rated at 2200 psi These are located on the back side of the machine and used to trans fill smaller D E or M size cylinders in the blast containment chamber These cylinders come fully connected and leak checked and should not have to be removed or serviced until they need to be re certified Effective 11 2010 14 Power Cord The power cord is designed for use at 230 VAC single phase An electrician will need to wire this into a dedicated circuit with a disconnect lockout Reserve Cylinder Valve This valve allows the reserve bank to be isolated from the system for the purpose of trans filling smaller cylinders in the containment chamber directly Reserve Cylinder Gauge The system is shipped with reserve bank of two 2 H K size 244 ft capacity steel cylinders This gauge shows the pressure in the reserve bank Fill Chamber Pressure Regulator This regulates the outlet pressure used for trans filling smaller cylinders loaded in the fill blast containment chamber Emergency Stop Button This button allows the oxygen generator power to be instantly shut off in the
32. g and parts handling process Pre Cleaning Hold Parts for Mechanical Engineering Review oy Ki e Fail Twice Parts Final Cleaning Pass Received and Hot Water and gt Labeling Inspected Detergent a Packaging Parts Received and Initial Inspection Upon determining which parts need to be cleaned the technician needs to perform an initial visual inspection under white light Check for the presence of visible residue on the parts including but not limited to oil grease dirt dust rust weld slag or pre existing thread sealant Effective 11 2010 u among others For parts that have an internal cavity that is not directly observable by the naked eye a lint free cloth that is first soaked in water can be inserted into the part and withdrawn for evidence of contamination No part failing inspection shall be used in any assembly Pre Cleaning Pre cleaning methods include soaking parts in a water based solution with an aqueous detergent using a wire brush or thread pick holding it under a wire brush grinding wheel or simply wiping it down with a clean rag Upon completion of pre cleaning the part should be clear of any visible contamination and ready for final cleaning Final Cleaning Final cleaning involves placing the parts in the parts washing machine adding an appropriate amount of detergent and running them through the cleaning cycle Consideration shall be given to the size
33. he machine Each of the components of the control panel and its operation will be described in more detail below Fill Blast Containment Chamber The cylinders are loaded and connected for refill at this chamber The purpose of this chamber is to protect the operator in the unlikely event of a cylinder explosion Side Access Door The side door provides access to the oxygen generator bank and many of the other components of the system Front Access Door The front door provides access to many of the system components Frame Inlet Air Filter Maintains the air flow through the enclosure and only allows air to pass through the bottom of the machine This filter can be accessed by reaching under the machine from the front and pulling it forward Upper Auxiliary Oxygen Port 70 psi The upper port allows for bypassing the high pressure oxygen compressor inside the MOGS and delivering oxygen at 70 psi 4 8 bar directly to a clinic hospital or other application In order to do this the oxygen compressor inside the machine must be switched OFF If this capability is used OGST recommends that an additional oxygen storage tank be installed and located next to the left side of the cabinet Lower Auxiliary Oxygen Port 2200 psi The lower port allows for the expansion of the reserve cylinder bank beyond the two 2 cylinders that are included in the frame of the machine From this port an auxiliary high pressure mani
34. ine stand clear and do not allow oxygen to embed itself within clothing A spark could ignite the clothing violently Effective 11 2010 6 Product Information Features and Applications The OGSI model MOGS 100 is a self contained oxygen generating system that uses Pressure Swing Adsorption PSA technology It allows users to generate medical grade oxygen conforming to United States Pharmacopeia USP XXII oxygen 93 Monograph to be used on site It concentrates oxygen up to 93 3 purity Features Durable e MOGS 100 unit has a PLC controller with a UL listed electrical panel It has a sound attenuating enclosure with slam action latches and lift off hinges Economical e The MOGS 100 unit reduces oxygen supply costs by 80 or more in most cases It consumes less than 1 kWh of energy to fill one MI size oxygen cylinder It eliminates all delivery and handling charges from oxygen suppliers Dependable e Having a MOGS 100 unit assures care providers that their oxygen supply chain will not be disrupted in the event of a disaster The system itself can be transported for use at a disaster site It can be moved by truck and fits easily through a standard 36 wide doorway Effective 11 2010 Applications The MOGS 100 can be used in various applications A few examples are given below EMS Emergency Medical Services Fire Departments Hospitals and Clinics Veterinary Cent
35. initialize the system when pre programmed conditions are satisfied and the ON OFF button is in the ON position The MANUAL mode requires the user to press an additional START button to initialize the system This is intended to prevent an inadvertent system initialization With the system running ensure that the air compressor indicator toggles from red to green The oxygen booster compressor should toggle from red to green after the oxygen compressor is activated and that will occur when the system has produced oxygen of 90 purity or greater for 4 minutes The system should continue to operate until the desired pressure is reached a fault is encountered or it is de energized by the user Shut down The MOGS 100 unit has been programmed to automatically de energize when cylinder pressure reaches the set point normally 2200 psi i e 152 bar indicating that cylinder filling is complete The machine may be manually de energized by pressing the Power button on the CONTROL screen to OFF at any time The machine can also be de energized at any time by pressing the red Emergency Stop button on the front of the control panel Pressing this button only breaks the electrical power to the machine There may still be oxygen stored at high pressure inside the system which could represent a hazard in an emergency situation Effective 11 2010 27 Troubleshooting Guide Problem Sign Cause Solution No power
36. isfaction Survey Help us serve you better Please take our Customer Satisfaction Survey at www ogsi com Effective 11 2010 51 Appendix Spare Parts List PART NAME PART NUMBER QUANTITY 4 NC Direct Acting Solenoid Valve 1510009 CD3 3 4 Check Valve 1530001 G02 l 25A Motor Contactor 1810107 003 1 100 psi Air Pressure Transducer 1910001 100 l Im Compressor Inlet Filter Change every 6 months 2180001 E01 8 Replacement Air Compressor Assembly 7030004 R04 2 Double Solenoid Valve 230VAC 1510007 220 1 100 psi Pressure Transducer medium oxygen pressure 1910001 100 1 50 psi Pressure Transducer low oxygen pressure 1910001 050 1 Oxygen Booster Pump 212000T 220 l Oxygen Purity Sensor 3110003 008 1 Replacement OEM Module 7010006 R02 1 Replacement Set of Sieve Beds 7060003 001 5 ee 212602700 i Touch Screen Panel 1810001 S6C 1 After Cooler 2140003 220 1 Cabinet Filter Change every 6 months 2180001 J01 4 Domnick Hunter Element AO 020 Change annually 218D020 001 l Manual Available Free on Website 9000000 004 1 Effective 11 2010 Oxygen Cleaning Procedure Scope This procedure sets forth the cleaning requirements for parts that are used in the construction of OGST oxygen systems and are in the gaseous oxygen product stream including but not limited to valves tubing fittings manifolds and pipes Objective The objective of this p
37. last chamber that the small cylinders can be filled in Fill Chamber 2 This is the right side blast chamber that the small cylinders can be filled in Effective 11 2010 20 Process Flow Description The incoming air enters the machine through a filtered opening in the floor of the machine frame This opening is protected by a furnace filter type element which is 12 x 16 x 1 The air is drawn into the air compressor bank after being filtered through one of two additional inlet air filters on the feed air manifold The air is compressed in the compressor bank and is directed through an air to air heat exchanger and into the grey storage tank The fan that is used in the air to air heat exchanger also serves the purpose of drawing fresh air into the machine through the floor of the frame and removing the air that is heated by the operation of the components inside the machine The resulting hot air is released through the top of the machine and can be ducted outside in hot environments or used as a supplemental heat source in cold environments The clean compressed air is then sent into one of the five sieve bed sets These are the oxygen generators Each bed produces oxygen until the sieve in that bed is saturated with nitrogen When this occurs the feed air flow is directed to the other bed which continues the production process While the second bed is producing oxygen the first bed is releasing into the
38. me contaminated with water and oil vapors This is why regular filter element replacement is crucial to trouble free operation The filter elements are inexpensive and require semi annual maintenance Effective 11 2010 9 External Components Front View WWW OGSI COM 1 Control Panel Fill Blast Containment Chamber Side Access Door Front Access Door ao fF VN Frame Inlet Air Filter Underside Effective 11 2010 10 Rear View 1 Upper Auxiliary Oxygen Port 70 90 psi 2 Lower Auxiliary Oxygen Port 1900 2200 psi 3 Reserve Oxygen Cylinder Bank 4 Power Cord Effective 11 2010 11 MOGS 100 with Auxiliary Manifold and Cylinders WW W OGSI COM 1 Auxiliary Cylinder Filling Manifold Shown with Copper Pigtails Optional 2 Extra Reserve Cylinders Optional Effective 11 2010 Control Panel mech Oxygen Compressor Outlet Pressure Gauge Reserve Bank Valve Reserve Bank Pressure Gauge Fill Chamber Pressure Regulator Regulated Pressure to Containment Chamber Emergency Stop Button Valve Fill Chamber 1 Gauge Fill Chamber 1 D Oo N oO A A WO N Valve Fill Chamber 2 Gauge Fill Chamber 2 mech mech Touch Screen Pad Effective 11 2010 13 External Components Description Control Panel This feature is the operator interface area for normal control of t
39. n 60 minutes are displayed at a time and 24 hours are stored in memory If power to the machine is lost Emergency Stop button is pushed in machine is unplugged etc the chart memory will be lost The GRAPH screen shows the history of what has been displayed on the GAUGE screen for up to the previous 24 hour period Note that the machine only has a 24 hour memory when it is ON so after 24 hours it will start deleting or writing over previous history In addition these readings are stored in dynamic memory so if the machine is de energized these readings will be lost The readings that are recorded are for Oxygen Purity Bed Oxygen Pressure Air Tank Pressure and Oxygen Tank Pressure This information can be stored indefinitely when downloaded to computer with an optional touch screen SD card Effective 11 2010 38 Alarm Screen This feature displays warnings when any of the following faults occur Oxygen pressure has fallen below acceptable limits This fault does not de energize the machine Oxygen purity has fallen below acceptable limits Air compressor thermal switch has tripped Oxygen compressor thermal switch has tripped Air compressor has been running one hour and the purity has not yet reached an acceptable level Instructions will be displayed on the screen to clear any warnings For certain alarms the machine will not operate until the CLEAR WARNING button has been pressed The ALARM screen displays w
40. ngs showing performance for up to the previous 24 hours Self diagnostic alarm panel The following pages give a detailed description of the 8 individual screens Effective 11 2010 30 Language Screen Ve lcome Bienvenido Bienvenue SELECT LANGUAGE SELECT LANGUAGE Ey E SELECT LANGUAGE Main Menu The language screen enables the user to choose the language English French or Spanish After choosing a language select MAIN MENU Effective 11 2010 31 Password Screen Please Enter Appropriate Password ENTER PASSWORD This screen prompts the user to enter the password supplied by the manufacturer gt Select PASSWORD AREA gt Enter the password using the numeric keypad displayed on the screen gt Select ENTER The password will be verified and the screen will change to the CONTROL screen when the password is accepted Effective 11 2010 32 Main Menu Screen This screen allows the user to navigate through the program from screen to screen and it will get you where you need to go inside the program Note A notification will appear at the top of the screen only if the machine has the timer set and is turned ON Effective 11 2010 33 Control Screen OGSI MODEL MOGS 168 CONTROL SCREEN Main Menu The CONTROL screen is used to operate the machine The mode of operation AUTOMATIC or MANUAL is selected here and the system
41. of the Products or any component parts or equipment that constitutes part of the Products by anyone other than an authorized representative of OGSI The authorized service representative must obtain prior approval from OGST s Service Manager before performing any warranty work c External Causes e g flood hurricane tornado fire any natural disaster or any event deemed an act of God Molecular Sieve Replacement The breakdown of the molecular sieve inside the generator dusting of the sieve only occurs if excess water oil is entrained in the feed air stream Under no circumstances is the molecular sieve covered under any warranty by OGST If sieve dusting occurs on your machine check the air compressor air dryer and filter elements Other Matters OGST is not liable for any special indirect punitive economic incidental or consequential losses or damages including without limitation loss of use malfunction of OGSI products replacement oxygen charges delays or lost savings related to the Products or otherwise even if OGST shall have been advised of the possibility of such potential losses or damages Limits of Liability OGSI Oxygen Generator products shall not be used for breathable or medical oxygen applications unless they are assembled with the appropriate support equipment tested and operated in compliance with either American Canadian or ISO norms for hospital oxygen systems Effective 11 2010 4 S
42. off the cylinders will become projectiles and serious injury or death could occur Detaching a H K type cylinder With the machine turned off close each of the appropriate manifold and cylinder valves Warning Oxygen under high pressure is present The use of safety glasses and hearing protection is required Slowly disconnect the steel whip from the cylinder valve using 1 g wrench Be aware of the venting of oxygen under high pressure If difficulty is encountered while attempting to remove the steel whip open the appropriate manifold valve and then slowly open the bleed valve to vent the pressure This will allow easier removal of the steel whip Ensure that both manifold and bleed valves are closed after venting pressure Attaching and filling smaller cylinders in the blast containment chamber Smaller cylinders D E or M size can be filled from the reserve bank of larger H K type cylinders at anytime even if there is no power to the machine If the machine is operating the reserve bank can be closed off and the small cylinders can be filled directly from the machine This takes a little longer but it conserves the reserve bank Start by opening the door to the blast containment chamber push the green bar down and set the cylinder in one of the two fill chambers Connect the small cylinder to the filling whip These whips and the small cylinder should both have CGA 870 Valve adapters Then open the valve to the appropriate fill p
43. ort on the control panel If the machine is filling the small cylinder directly it will shut off when the cylinder is full If you are trans filling from the reserve bank observe the pressure indicator to see when the small cylinder is full Be sure to close the cylinder valve and reserve bank valve before trying to remove the small cylinder from the filling whip Warning Oxygen under high pressure is present The use of safety glasses and hearing protection is required Disconnect the steel whip following the procedure outlined in Detaching a H K type cylinder above Effective 11 2010 48 Preventive Maintenance Frame Inlet Air Filter Element Replacement The Frame Inlet Air Filter Element provided with the MOGS 100 must be replaced every three to six months depending on the amount of dust and debris in the operating location The element helps to maintain the quality of the feed air supply and to keep the inside of the machine relatively clean This filter element is accessed by reaching under the front of the machine and pulling it forward While these can be supplied by OGST as part of a spares kit the easiest way to get replacements is by going to any hardware store and buying 16 x 12 x 1 furnace filters Failure to replace the filter element on schedule will result in the warranty becoming invalid Inlet Air Filter Element Replacement The air filters 2 keep dust and dirt from entering the air compressors
44. pe or a similar pipe dope such as Krytox grease It is equally important to ensure that the threads on all compression fittings such as the CGA 540 connections on K type cylinders are clean unless the threads are stainless steel on stainless steel All fittings should be tightened with a wrench much tighter than hand tight Once the manifold is built and installed it needs to be checked for leaks with oxygen at 2200 psi 152 bar This can be done by shutting the valves on all bottles and using the MOGS 100 to fill the manifold to 2200 psi 152 bar Each joint should then be checked for leaks by applying soapy water to the joint using a spray bottle or a small paintbrush If bubbles are formed it means that there is a leak If a leak is found the joint should be tightened further with a wrench If this does not work the joint should be disassembled and cleaned then reassembled and tested If this does not work the leaking fittings need to be replaced Effective 11 2010 45 Cylinder Filling Procedures Warning High pressure oxygen may present a hazard Always follow proper operating procedures and open valves slowly Rapid pressurization may result in personal injury Safety glasses and hearing protection are required when venting oxygen under high pressure The intended use of the MOGS 100 is to fill large K type cylinders The smaller M type cylinder can then be trans filled from the K type cylinder Important Your MO
45. reen 647401 Please take appropriate measures to keep this password secure and prevent unauthorized access Using the Manual This manual is intended as a guide for operators of OGSI Oxygen Generators and Oxygen Generating Systems It includes information on our warranty policy features functions applications proper set up and installation operation and maintenance of our products The following symbols are used throughout the manual Information Do not use product before Electrical Hazard reading the manual 7 Sound Fire Hazard D 4 No Smoki Warni o Smokin arnin 4 No Open Flames Power ON OFF i Flow Meter O Timer LA X No Oil Ce Not Connected to Outlet gt Effective 11 2010 Initial Inspection The crate should be opened and inspected immediately upon delivery Unpack the unit at once and perform a visual inspection to determine if it is dented bent or scratched Also check to make sure the power cord is attached and that the control panel has not been damaged in any way during shipment If for any reason the unit should need to be returned in the future the original crate is the best way to ship it back to the manufacturer Claims of damage due to freight handling can only be filed by you the consignee as OGSI shipping terms are Free On Board FOB North Tonawanda NY USA This means that once the equipment leaves our dock you are the owner of it OGS
46. rmal operating conditions Eventually they will need to be re built or replaced This operation is usually needed after 8000 10 000 hours Oxygen purity and flow rate along with feed air pressure delivered to the sieve beds will all be indicators that the air compressor has expended its useful life Replacement in the field is possible and takes about 30 minutes per compressor Effective 11 2010 49 Oxygen Generator The oxygen generators are designed to run 24 hours a day for many years without failure The most common failure mode is molecular sieve contamination due to high moisture content These units can be re built at OGSI or new units can be installed in the field Replacement in the field is possible and takes about 20 minutes per generator Oxygen Booster The Oxygen Booster is a single stage oil less compressor that should last two 2 to four 4 years under normal conditions Low Oxygen Tank pressure less than 60 psi or 4 1 bar will be an indicator that this booster needs to be replaced Replacement in the field is possible and takes about 30 minutes per compressor Oxygen Compressor The high pressure oxygen compressor is a two stage oil less compressor that will require maintenance at normal intervals OOGST does sell the spare parts for this compressor as a kit Please consult OGST for the spares kit for this machine and have the serial number for the oxygen compressor or the MOGS Unit available when you
47. rocedure is to provide personnel with clear directions and an understanding of how parts are to be cleaned and why that is important This document is based on guidelines provided in publication CGA G 4 1 2009 which is produced by the Compressed Gas Association CGA and is intended to ensure that our internal procedure is compliant with that publication Safety Harmful contamination such as grease dirt oil dust solvents weld slag sand rust and previously applied thread sealants on parts that come into contact with oxygen can cause a combustion reaction resulting in system degradation or failure or worse a hazard to nearby personnel Care needs to be taken in the cleaning and handling of components used in oxygen service to prevent any contamination related failure While the CGA G 4 1 2009 standard makes allowance for cleaning parts using caustic agents acids or solvents the OGSI procedure will use only mechanical soaking wire brushing or grinding means for pre cleaning and hot water cleaning with aqueous detergents for final cleaning This is done to reduce any chemical exposure risk to personnel and to eliminate the additional steps needed to remove these cleaning agents from the parts themselves Training Personnel involved in the cleaning and preparation of parts used in oxygen service should be trained in these cleaning procedures and be familiar with this document Process Flow Chart The flow chart below describes oxygen cleanin
48. s should not be dropped or permitted to strike each other or any other surface Do not drag or slide cylinders use a suitable hand truck fork truck roll platform or similar device firmly securing the cylinders for transporting Do not store oxygen cylinders with flammable gas cylinders Stored oxygen and fuel gas cylinders should be at least 20 ft apart preferably separated by a fire resistant partition For additional information refer to the CGA publications that can be found at http www cganet com See also ISO publication 10083 that can be found online at http www iso org Effective 11 2010 5 Operating OGSI Oxygen Generators are self contained systems for the production of high concentration oxygen Although oxygen itself is not combustible it can be very dangerous It greatly accelerates the burning of combustible materials Precautions should be taken to avoid a fire in the area of the generator amp Smoking should not be permitted in the area where the generator is located D All oxygen connections and hoses should be kept clean and free of grease oil and other combustible materials gt Valves controlling oxygen flow should be opened and closed slowly to avoid the possibility of fires or explosions that can result from adiabatic compression gt Do not attempt to modify or enhance the performance of an oxygen generator in any way When bleeding a tank or l
49. shape and number of parts to be cleaned at one time to ensure that the system is not overloaded or its function impaired The cleaning temperature inside the washer shall be 120 F 49 C to 140 F 60 C and the detergent to be used shall be Cascade This detergent has a flash point above 105 F 41 C but it does not sustain combustion and there are no exposure controls for it Parts can be removed from the washer once the drying cycle is complete Inspection Upon completion of the final cleaning cycle all parts should be removed from the parts washing machine and inspected for any residual contamination The item shall be observed to confirm the absence of any contaminants including any oil grease detergent moisture lint or other foreign materials If any material remains on the part after the final cleaning cycle the part shall be returned for a second round of pre cleaning and final cleaning Packaging Once a part or assembly has been cleaned for oxygen service it should be protected to prevent recontamination if it will be put into storage Small to medium sized parts should be packaged in plastic bags Larger assemblies should be bubble wrapped or wrapped in foam material and then moved on to final packaging in boxes and or crates Labeling Once a part or an assembly has been cleaned and packaged for oxygen service it should be labeled per the customer s instructions but at a minimum e contain the statement Cleaned for O
50. to RUNNING when it is energized gt Advanced Settings This feature allows the user to modify timer and clock settings It also allows you to check the number of hours that the machine has been operating Effective 11 2010 35 Advanced Settings Screen HOURS METER REALTIME CLOCK 13 45 88 18 18 gt Timer Setup If there are particular hours of the day you want the machine to run you can enter the hour and minutes military time you want into the starting and ending time inputs gt Setting Timer This button activates the timer When the SETTING TIMER feature is in use the machine will run only during those times entered in the TIMER SETUP above gt Hours Meter This meter displays the accumulated operating time of the system This meter will increment only while the system status is CYCLING and will reset to zero 0 after 10 000 hours Most maintenance will be related to the number of run time hours the machine has accumulated on it gt Real time Clock The hours may be updated to synchronize with the current time zone by pressing the appropriate button below the display Each button is password protected gt Timer Adjust These two buttons will either increase or decrease the Realtime Clock by one hour Effective 11 2010 36 Gauge Screen SU Bm BEE Lei ua LESSER Feel o 20 40 60 80 100 12 24 36 48 60 teen SEET 3 6 9 12 15 o 20 48 60 80 100 be
51. trol Panel there are two 2 va NPT threaded ports Upper Port The upper port allows for bypassing the high pressure oxygen compressor inside the MOGS 100 unit and delivering oxygen at 70 psi 4 8 bar directly to a clinic hospital or other low pressure oxygen demand In order to use this option the oxygen generator needs to be set to automatic on the touch screen and the oxygen compressor inside the machine must be manually switched to the OFF position t will normally be in the AUTOMATIC Mode There is a three position switch on the control panel which is accessible when the front access door of the machine is open You cannot fill cylinders and draw oxygen from the 70 psi 4 8 bar port at the same time A low output pressure will result if this is attempted If this capability is used OGST recommends that an additional oxygen storage tank be installed and located next to the left side of the cabinet MOGS 100 should use a 120 gal storage tank See drawing on the following page for suggested layout Effective 11 2010 46 Low Pressure Set up Lower Port The lower port allows for the expansion of the reserve high pressure cylinder bank beyond the two cylinders that are included in the frame of the machine From this port an auxiliary high pressure manifold can be connected increasing the size of the reserve bank by 3 4 etc additional cylinders These additional high pressure reserve manifolds along with extra
52. xygen Service e contain the date of cleaning or packaging References The following publications were referenced in the creation of this document e CGA G 4 1 2009 Cleaning Equipment for Oxygen Service Compressed Gas Association Inc 4221 Walney Road zu Floor Chantilly VA 20151 www cganet com e Oxygen Cleaning Procedure Rev L 8 05 RIX Industries Inc 4900 Industrial Way Benicia CA 94510 www rixindustries com Effective 11 2010 II Oxygen Sensor Calibration The oxygen sensor is located at the bottom of the right side cabinet access door The Zero adjustment screw is shown below as viewed from the right side of the open door The sensor is a Model 120J OxyAlert 2 Gas Sensor with 1 accuracy It is made by Douglas Scientific Compass Controls Zero Adjustment Oxygen Sensor Location The Zero Adjustment Screw is used to calibrate the zero point of the sensor Normal air has 20 9 oxygen in it and air can be used as a zero gas for sensor calibration Procedure e Disconnect the oxygen sample line feeding the sensor and let the sensor sit in the open air for 15 minutes e Verify the sensor reading matches the purity of the oxygen in the air 21 If the display does not say 21 adjust the screw until it does Then re connect the sample tap line to the sensor and continue running the system The oxygen reading should now accurately measure the purity being produced Effective 11 2
Download Pdf Manuals
Related Search