Operations Manual
Contents
1. Press the right displays Wait for the appliance to heat up to the READY condition before cooking 1 2 To turn the appliance OFF Press the DFF 1 3 To start a cook When the display is showing REAR JY the appliance has reached set temperature and is ready to cook Press a basket key then the desired product key and place product into the vat The left display will show the basket color and the key Display will momentarily show the software version number and then key Some messages may show in both left and Y B INDICATOR FLASHES WHEN SET Ta 4 Pd Typical Product Key product key while the right display shows the time remaining in the cook In the example above RED lane is cooking product 4 left display with 1 minute and 7seconds remaining right display Up to three cooks may run together While cooks are running the displays will always show the cook with the least time remaining Longer running cooks will flash their indicators at a slower rate Cook time remaining on these keys may be checked by momentarily pressing the basket keys Page 3 of 12 L20 260 Rev 2 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lanes Selection Features CEA Pitco P N 60126803 1 4 To cancela cook Press and hold the basket key to cancel a cook The indicator above the product key will turn off indica2. when no active cooks Page 7 of 12 L20 260 Rev 2 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lanes Selection Features Pitco P N 60126803 3 To Change Options Level 2 for the Store Manager The display must show PROGRAM from section 2 to change these options When the product key 0 is pressed the display will show SELECT OPTIONS Indicator lights above product keys will illuminate to represent options that may be changed Each option listed below uses the product key 0 to toggle or scroll through available choices in the display When the correct value is displayed press the key to save choice The display will again return to PROGRAM for another option selection 3 1 _ Fahrenheit or Celsius Display The Controller will display temperatures in the Fahrenheit or Celsius scales The default scale is F With display showing PROGRAM press the product key 0 Q Display shows SELECT IGPTIONS 1 Q Press product key 1 display shows DEGREE n F OR C where n is the current i setting Q Use the product key 0 to scroll through choices F or C Press P key to save choice a Display shows PROGRAM 3 2 _ Password Change or Required With factory settings an operator password is not required to enter programming Levels 1 and 2 The password may be activated or changed in these steps With display showin
3. setting Q Use the product key 0 to scroll through choices Q Press P key to save choice Display shows PROGRAM Factory default setting is for 3 Lane Control L20 260 Rev 2 Page 10 of 12 Q Press product key 8 display will show LANES n 30r 4 where n is the current 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lane Selection Features Pitco P N 60126803 3 9 _Seback Time and Temperature settings With display showing PROGRAM a Display willshow SELECT OPTIONS Q Press key 9 Display shows TIME nn SET BACK where nn is the time the control must be idle not cooking to enter the setback state The default setting is 00 meaning that the setback feature is disabled Entry on any non zero value will activate this feature The valid range of time entry is 0 to 99 minutes Entering 00 will disable the setback feature Typical values are 30 minutes Q Press P key to save a Display shows TMP 2SOFISET BACK press the product key 0 Q Enter the number of minutes nn using the numbered keys Q Enter a new setback temperature using the numbered keys The valid range of temperature entry is 225 to SP 15 F Factory default value is 250 F Q Press P key to save setting Display shows PROGRAM 3 10 To Exit Programming Level 2 press the P key P HEATING With display showing PROG
4. IMPORTANT INFORMATION FOR FUTURE REFERENCE Record the following information from the appliance ID plate and retain this manual for the life of the equipment Model Serial Operations Manual Covering Pitco P N 60126803 Single Vat Control With Set Back and Lane Selection Options Pizza Hut w Fryer Control WingStreet This control was developed specifically for Pizza Hut for use on WingSireet products It utilizes the latest in microprocessor technology and is completely solid state WingStreet controls offer the latest cooking technology including temperature and time compensation that requires no user adjustment for consistently cooked product Other features include selectable melt cycles and a drain valve interlock 10 product keys are available to each of 3 or 4 cooking lanes Each product key may be programmed with cook shake and hold times to keep pace with changing menus over time This manual details the operation and adjustment of the Pizza Hut Fryer Control The target audience for this text is the Store Manager This manual reveals all non service adjustments that can be made by keyboard eniry including passwords 20 260 Rev 2 10 4 07 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lanes Selection Features Pitco P N 60126803 Key Locations and FUNCTIONS s1csescccseencececsnencssnensessenssnencasnansaseensne
5. 0 to scroll through choices n 1 2 3 Beeper tone will change as each selection is made Q Press P key to save choice Display shows PROGRAM 3 4 __ Language Selection With display showing PROGRAM a Display willshow SELECT OPTIONS E Press product key 4 display shows ENGLISH LANGUAGE Use the product key 0 to scroll through choices ENGLISH ESPANOL FRANCAIS DEUTSCH HOLLAND press the product key 0 Q Press P key to save choice Display shows PROGRAM 3 5 Melt Cycle Type This adjustment allows selection of the melt cycle type and requirement when starting the appliance from a cold start With display showing PROGRAM a Display willshow SELECT OPT IONS Press product key 5 display shows LIQUID the default setting press the product key 0 Use the product key 0 to scroll through choices liquid solid or no melt Q Press P key to save choice Display will again return to PROGRAM Page 9 of 12 L20 260 Rev 2 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lanes Selection Features Pitco P N 60126803 3 6 _ Recovery Test Value This controller maintains a record of heat up times for the appliance A poorly running appliance will have increased recovery times stored in this display There is no selection done here just the display of recovery time values With display s
6. 2 Entry of a password when NOT required will not interfere with the programming process With no cook timers running displays will show one of the following displays ME L T HEATING READY or NOTREADYISET JACK Press the P key If display shows If display shows IPASS PASSWOR J a password is required PROGRAM you do not need to enter a password Level 1 amp 2 Password f 6 f 6 8 4 Oleo o Enter password using the product keys as IY a numeric keypad for entry With correct password entry display will show PROGRAM From the PROGRAM display continue with this section or go to section 3 or 4 2 1__ To Set Cook Temperature a Pressthe key once The display will show SET xxxF TEMP or SET xxxC TEMP where xxx is the current temperature setting Q Use the product keys for numeric entry to adjust the current setting Press the P key to save setting Display now shows FROGRAM To exit here press P again or continue 2 2 __ To Change a Product Key Cook Shake Hold and Hold Pre Alarm Times For each product key Cook Shake Hold and Hold Pre alarm times are set in this section With display showing PROGRAM change 2 2 1 Cook Time Cook Time may be set for each product key To deactivate any product key enter a zero value for cook time continue with the
7. control must be turned off 1 0 1 10 Set back Operation Operation of the setback features requires set up values be entered refer to service manual section 3 8 Factory default settings are with this feature inactive Operation Each time a cook is performed the setback timer is reset When no cooks occur for the duration of the setback time the control will enter a setback state and maintain a reduced vat temperature Both time and temperature of this setback feature are adjustable by the store manager 1 When the control is in the setback state the display will show NOTREADY SET BACK 2 Press any colored basket key or product key to exit setback 3 If the vat temperature is below the READY band a rapidly pulsing alarm will sound to warn the operator Display will show LOW TEMP WAIT 959 The miss display will show the approximate time needed for the vat temperature to rise to cooking temperature Wait for the temperature to return to the REA TY condition before lowering basket into the fryer Page 5 of 12 L20 260 Rev 2 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lanes Selection Features Pitco P N 60126803 2___ To Enter Programming Level 1 for the Store Manager Note The factory default setting for this control does not require a password to be entered However the password requirement and value may be changed in section 3
8. time setting HEATING READY NOTREADY SET BALK when no cooks are running If cooks are running the least time remaining will be displayed After a few moments the display will return to MEL T or Typical displays using key 4 as an example Key 4 Cook Time 4CK is set for 3 minutes and 28 seconds Key 4 Shake Time 4SH is set for 2 minutes and 00 seconds before the end of the Cook Default value is 00 00 or inactive Lf E K Key 4 Hold Time 4HD is set for 15 00 minutes This is the amount of time cooked product may sit in holding bins before a Lf H new batch is started Default value is 00 00 or inactive Key 4 Hold Pre Alarm 4PA is set for 00 00 and is inactive default Lf H T setting When activated his alarm warns the operators that the Hold Time is about to run out In a few moments the display to MEL T HEATING READY INOTREADYISET PACK Or L20 260 Rev 2 Page 4 of 12 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lane Selections Features Pitco P N 60126803 1 9 To perform a Boil Out operation Normal maintenance of a fryer requires regular tank cleaning This process involves draining the vat of oil and filling with water Cleaning solution is added and the control is set to boil by one of the following methods 1 9 1 Automatic Boil Entry Water Detection
9. Fill the appliance with water and turn the appliance on Heat will be applied to the vat warming the water This control will detect the presence of water by temperatures not rising above the boiling point of water 212 F 100 C After a time at this temperature displays will show PRESS U BOIL Heat will be disabled until the operator responds to this prompt Pressing the 0 key is a YES response to the boil prompt If pressed display will show J L Heat will maintain vat temperature at 185 F 85 C for cleaning as long as the control remains on To exit boil mode control must be turned off Warning Pressing any other key at the PRESS 0 TO BOIL prompt is regarded by the control as a NO response With this response the control will apply heat to the vat as if oil were present in the vat With water in the vat a rolling boil will result This will cause undesirable foam over conditions And a potential steam burn hazards to operators performing cleaning operations 1 9 2 Manual Boil Entry After filling an empty vat with water turn the appliance on Press the bas ae aaa X for Fahrenheit Displays i key and enter key sequence 2 1 2 f control is set to display in the 2 Celsius scale press 1 0 0 keys to manually enter boil mode The display will show 97 L to indicate entry into boil mode J SSS Enter 100 for Celcius Displays To exit boil mode
10. RAM Display will return one of the normal displays MELT READY or INOTREADYISET PACK H 3 Page 11 of 12 L20 260 Rev 2 In the event of problems with or questions about your order please contact the Pitco Frialator factory at 800 258 3708 US and Canada only 603 225 6684 World Wide In the event of problems with or questions about your equipment please contact the Pitco Frialator Authorized Service and Parts representative ASAP covering your area or contact Pitco at the numbers listed to the left MAILING ADDRESS P O BOX 501 CONCORD NH 03302 0501 SHIPPING ADDRESS 10 FERRY ST CONCORD NH 03301 20 260 Rev 2 10 4 07
11. following section for each product key to a Pressthe key Q Display will show SELELT PRODUCT Press the desired product key to change The display is now showing nCK mm ss TIME where n is the key number CK means Cook and mm ss is minutes and seconds Q Use the product keys for numeric entry to adjust the current setting Press the i J key to save cook time and continue setup for this product key L20 260 Rev 2 Page 6 of 12 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lane Selection Features Pitco P N 60126803 2 2 2 Shake Time Shake time is an alarm that sounds during Cook Time to prompt operators to shake the basket Default for this value is zero meaning the Shake Time is inactive To use Shake Time the time value must be a non zero value and must be set to a value less than cook time Q Display shows NSH mmiss TIME where n is the key number SH means Shake and mm ss is time in minutes and seconds Q Use the product keys for numeric entry to adjust the current setting Press the o key to save shake time and continue setup for this product key Note The value entered for shake time is the time from the end of the cook 2 2 3 Hold Time Cooked product may stand in holding bins for a period of time This timer produces an alarm to inform operators to discard old product and start a new cook Default for this value
12. g PROGRAM press the product key 0 a Display willshow SELECT OPT IONS H Q Press product key 2 display shows SET PAS NEW PASS Use the product key 0 to scroll through choices NO PASS or PASS REQ Press P key to save choice Q If NO PASS is selected Display returns to PROGRAM a If PASS REQ is selected display will show PASSnnnn NEW PASS to prompt for new password Displayed value nnnn is the current password Use the product keys for numeric entry to change password Press P key to save choice Display then shows PROGRAM Note The factory default password 6684 will always work even if a different password is selected here L20 260 Rev 2 Page 8 of 12 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lane Selection Features Pitco P N 60126803 3 3 Beeper Volume and Tone Volume and Tone of the beeper alarm may be changed in this section Volume ranges are 1 2 and 3 where 3 is the loudest setting This model also has a selection for tone With display showing PROGRAM press the product key 0 Q Display willshow SELECT GPT ONS Press product key 3 display shows VOLUME n BEEPER Q Use the product key 0 to scroll through choices n 1 2 3 or T Beeper volume will change as each selection is made Q If T is selected an additional display is shown TONE n BEEPER Use the product key
13. howing PROGRAM a Display willshow SELECT OPTIONS Press product key 6 display will show RECOVERY TEST press the product key 0 recovery value and yyy is the last warm up recovery value Q After recording these values press the P key Display will again return to IPROGRAM 3 7 _ _Control or Timer Selection With display showing PROGRAM a Display willshow SELECT OPTIONS Press product key 7 display will show CONTROL Use the product key 0 to scroll through choices Control or Timer press the product key 0 Q Press P key to save choice Display shows PROGRAM Press the product key 0 Display will show FnnnLyyy where nnn is the factory Note If timer is selected heat control outputs are disabled leaving only the timer functions active Do not make this selection on Solstice fryer models 3 8 Lane Selection This control offer a selection between the Active cook lanes In the three lane mode the control responds to basket key location shown on the cover of this manual Lanes are defined as Yellow Blue and Red After September 2007 conversion to a 4 lane cooking control is possible In the four lane setting lane colors are Yellow Blue Red and Green To change to four lane mode follow these steps With display showing PROGRAM a Display willshow SELECT OPTIDNS press the product key 0
14. is zero meaning the Hold Time is inactive Q Display is showing nHD mm ss TIME where n is the key number HD means HOLD and mm ss is minutes and seconds Q Use the product keys for numeric entry to adjust the current setting Press the f key to save hold time and continue setup for this product key 2 2 4 Hold Pre Alarm Hold Pre Alarm is a timer setting that is used to warn operators that the Hold Time is about to expire To use Hold Pre Alarm the time value must be a non zero value and must be set to a value less than Hold Time Default value is zero meaning the Hold Pre Alarm is inactive Q Display is showing NPA mmi ss TIME where n is the key number PA means Pre Alarm and mm ss is minutes and seconds aN Q Use the product keys for numeric entry to adjust the current setting Press the K J key to save pre alarm time Note Value entered for hold pre alarm time is the time from the end of the hold period Display will again return to SELECT PRODUCT Repeat steps from section 2 2 to make changes to any other product keys or continue 2 3 _ To Exit Level 1 programming Display shows SELECT PRODUCT Press the P key Display shows PROGRAM Continue to section 3 To Change Options or exit here in the next step To exit Level 1 programming press the P key again HEATING Displays will show MELT are running or REATY
15. nsesnansaseensuensesuansaanaesasenssnenssnanesaaanes 3 1 1 To turn the appliance ON 3 1 2 To turn the appliance OFF 3 To start a cook 3 1 4 To cancel a cook 4 1 5 To view Vat temperature 4 1 6 To view Cooking Set temperature 4 1 7 To view Set Back temperature 4 1 8 To View Current Settings for Cook Sake Hold and Hold Pre Alarm 4 To perform a Boil Out operation 5 1 9 1 Automatic Boil Entry Water Detection cccscsssscssssesscsssesseenscssssesssesessessecenseessenseneesesescensessesesssenseasseoneesseases 5 1 9 2 Manual Boll Entry sccccccctsscssscsecssecccesscseveccasccsscesestessceteesssecznavecesocsdessucecvvapessoceastesscesvertsiecescestsdcaseesseasviiesscesassenseesevaczoss 5 1 10 Set back Operation 5 2 To Enter Programming Level 1 for the Store Manager u ss1ccssecrccerccsnecccsseensnenscanenceseessseenesnenessees 6 2 1 To Set Cook Temperature 2 2 To Change a Product Key Cook Shake Hold and Hold Pre Alarm Times 6 2 2 1 COOK TME added ener a wanna adenine yee inners ca vavee N Ea varead EAEE ASEA AN 6 2 2 2 Shake TIME ariris iranan errrrererrrereecrece reper reece cere rrerereererteeretrrrereerecery errr rer receperrrceee ere cererrereerer ere reet eee rt Ty 7 2 2 3 Hold ime Seenen a AE Gieetarhearvenstnensts 7 2 2 4 lollo Arade ESEE AEAEE EPE ANTL T E T 7 2 3 To Exit Level 1 programming 7 3 To Change Options Level 2 for the Store Manager cssscccseccsercssnencsseensssennsnensessnenssseensne
16. nsnasanes 8 3 1 Fahrenheit or Celsius Display 8 3 2 Password Change or Required 8 3 3 Beeper Volume and Tone 9 3 4 Language Selection 9 3 5 Melt Cycle Type 9 3 6 Recovery Test Value 10 3 7 Control or Timer Selection 10 3 8 Lane Selection 10 3 9 Seback Time and Temperature settings 11 3 10 To Exit Programming Level 2 11 L20 260 Rev 2 Page 2 of 12 1__ Key Locations and Functions 112 Cooking Computer Pizza Hut WingStreet w Setback amp Lane Selection Features Pitco P N 60126803 10 Product Keys Heat Demand Yi SB with Indicators Indicator 3 Basket Keys ON OFF Key Yellow Lane Blue Lane Red Lane Qa y 2 w g 1 2 3 4 5 6 7 8 9 0 o Bone Bone IP ch In Out Taters Pies Sick Wings Wings tiG FED YQ Al D7 Clock Key Displays show current operation Throughout this text a left only display will be printed as RED 4 When both left and right displays should be interpreted together this text will be show them as RED 4 1 07 Programming Key Thermometer Key 1 1 _To turn the appliance ON If power is applied to the appliance the displays will show JF F Displays will show one of the following MELT HEATING kor READY
17. ting a canceled cook If no other cooks are pending controller displays will return to REA DY 1 5 To view Vat temperature To view the actual vat temperature press the key The display will show HLT 3471F or ALT 150 where F is Fahrenheit and C is Celsius After a few moments the display will return to READY MELT HEATING or NOTREADY SET BACK if no cooks are running 1 6 To view Cooking Set temperature To view the set temperature press the key twice The display will show SET JSF or SET 111C where F is Fahrenheit and C is Celsius After a few moments the display will return to READY MELT HEATING or NOTREADY SET BACK if no cooks are running 1 7__ To view Set Back temperature To view the set temperature press the key three times The display will show 5 2 SUF or 5 9 I I C where F is Fahrenheit and C is Celsius After a few moments the display will return to READY MELT HEATING or NOTREADY SET BACK if no cooks are running 1 8 To View Current Settings for Cook Sake Hold and Hold Pre Alarm ON To view the current settings for any product key press the a key followed by the desired product key The display will show nCK mm ss followed by NSH mm ss then nHD mm ss ending with MPA mm ss Where n is the key number and mm ss is the
Download Pdf Manuals
Related Search