QuantumPro - Operation and Service Manual
Contents
1. changer see figure 2 On Single Price units using the DEX UCS Hand Held Computer attach the DEX plug ground connector to the vending machine frame see figure 1 Plug changer into vendor socket Page 8 Acceptor DEX UCS N Ground gt EA Connector Acceptor Figure 1 Main Logic Board LED Option Switches Figure 2 SECTION 2 INSTALLATION Mounting Holes Mounting Figure 3 Inventory Buttons Coin Tube Loading Door Figure 4 Installing the Changer cont d 7 For Single Price units set the desired vend price and options on the changer refer to Setting the Vend Price and Option Switch settings 8 Press top of the acceptor into the changer housing until the acceptor latch locks 9 Load the tubes with coins see Hand Loading and Loading Through the Acceptor figure 4 10 Optional Set the coin tube float levels refer to Setting The Float Mode Levels 11 Check to make sure the front cover tube shield and acceptor are properly installed 12 Apply power to the vendor 13 Test the changer with a variety of coins to ensure proper operation Page 9 SECTION 2 INSTALLATION G Model Controller Vendor Interface 24 Volts DC and 5 Volts Logic Supplies Communication Return USQ G Receive CAQ G MEER VDC Return 34 ET UU Vending Machine Controller Coin Chang2. 925359 922161 408544 408540 922161 921810 921489 906617 923362 922783 DESCRIPTION Mainplate and Coil Operating Lever Spring Operating Lever Retaining Ring Gate Lever Pivot Screw Gate and Coil Assembly Gate Board 700 Series Keypad Gate Cover Assembly Mirror 450 x 375 Front Cover Intermediate Cover and Mirror Screw Flat Head 4 5 16 Validation Debounce Rail Sorting Debounce Rail Hand Loading Door Hand Loading Door Spring Accept Reject Door Sort Door Cashbox Door Diverter Pivot Pin Short Diverter Pin Coin Stop Plunger and Yoke Assembly Tube C Gate and Plunger Assy Solenoid Spring Copper Solenoid and Frame Assembly Spring Retention Plug Tube B Gate and Plunger Assy Self Locking Hex Nut 8 32 Acceptor Logic Board Rear Cover Acceptor Serial Label Acceptor Tune Label Acceptor Configuration Label Debounce Plate Screw Pan head 4 5 16 QuantumPro Front Cover Decal Anti Stringing Lever Acceptor Gasket Mainplate Insert Mainplate Textured Lens Sorting Lens Multifrequency Coil Assembly Coil Assembly Saltwater Protection Decal Gate Lens Gate Pin Gate Spring Water Protection Decal PVC Foam l lt HS C a Page 25 SECTION 6 EXPLODED VIEWS Payout Base Assembly Quant
3. Acceptance hot Vend Relay normally closed hot NC no connections G N S COIN CHANGER JONES PLUG 55 SIDE Page 12 SECTION 3 CONFIGURATION Single Price S Models SETTING THE VEND PRICE OPTION SWITCH Located behind the acceptor in the middle right hand side of the changer housing are twelve switches see Figure 2 The vend price is set using the first eight switches the last four switches are used to enable or disable different options VEND PRICE The vend price is set in single increments up to 255 times the lowest denomination coin accepted by the changer and routed to a coin tube In most cases this will be a nickel Example If the lowest denomination coin accepted to a tube for payout is a nickel the highest vend price setting would be 255 times 05 or 12 75 in this case the value of the price switches are lI EN o 3 20 6 40 O QG N When the top the rocker switch is pushed in it is in the ON position If switches 1 3 and 4 are ON the vend price would be 65 if the lowest denomination coin accepted to a payout tube is a nickel OPTIONS Switch A Switch 9 Controls the escrow feature of the changer ON Escrow inhibited OFF Escrow enabled Switch B Switch 10 Not used Switch C Switch 11 Vend signal length ON Vend is held until a selection is made OFF Vend is pulsed 300 msec Switch D Swi
4. has been selected the LED will flash a 1 second 50 ON 50 OFF sequence Drop the appropriate coin for the tube you have chosen into the acceptor An accepted and validated coin will be routed and assigned to the tube you ve chosen Page 18 Example For a payout configuration of 25 10 10 05 USQ 708 Press and release inventory button A insert a quarter through the acceptor Press and release inventory button B insert a dime through the acceptor Press and release inventory button C insert a dime through the acceptor Press and release inventory button D insert a nickel through the acceptor Any coin dropped through the acceptor before a coin tube is selected will be routed to the ven dors cashbox Valid coins not assigned to a tube will also be routed to the cashbox To save the new routing information and exit the routing mode hold the coin return lever down for 4 5 seconds until the acceptor LED returns to its normal pattern or wait 45 seconds and the Four Tube changer will automatically save the routing information and exit this mode NOTE If power is removed from the changer before the rerouting information is saved all new routing information will be lost SECTION 4 Routine Maintenance Routine maintenance will improve performance and extend the life of your QuantumPro changer and reduce the need for more involved repairs Frequency of maintenance will depend on env
5. 7 74 79 CAN 2 00 9 87 94 SECTION 1 General Information Specifications Power Requirements by model Single Price S 120VAC 60Hz acu MA IT 95 to 130 VAC 6OHz Logics L uuu A 15 pin 24 VDC BO 20 to 30 full wave rectified 1 5Amax Operating Temperature 0 to 150 Degrees Fahrenheit 18 to 65 Degrees Celsius Storage Temperature 22 to 160 Degrees Fahrenheit 30 to 72 Degrees Celsius Relative Humidity 20 to 98 Noncondensing Operating Attitude Vertical 3 degrees Physical Dimensions Height 14 77 inches base to top of coin return lever Width 5 47 inches Depth 3 25 inches gate open 3 00 inches gate closed Shipping Weight Approximately 7 pounds Page 7 SECTION 2 INSTALLATION Installing the Changer 1 2 Remove power from vendor Remove the acceptor from the changer by pressing down on the acceptor latch releas ing the acceptor Rotate the top of the acceptor forward away from the changer see figures 1 and 2 Unplug the ribbon cable from changer Free the lower acceptor studs from the changer housing Place the acceptor in a clean area With the acceptor removed set the mounting holes in the back of the changer housing over the mounting screws in the vendor Tighten snugly see figure 3 Re install the acceptor by inserting the lower acceptor studs into the changer housing guides Plug the ribbon cable into the
6. NE E E Page 30 0 0 000 00 boca 00 yo oo Ob p 000 00 ir d 200 BB ggl 407471 SINGLE PRICE Eu HB LOGIC BOARD SECONDARY TRANSFORMER CONNECTOR S CONFIGURATION MUHU a a NOTES Page 31 Coin Acceptors Inc products are patented and patents are pending in the United States and throughout the world C Coin Acceptors Inc 300 Hunter Ave St Louis MO 63124 Coinco Publication No 925555 Rev 1 1 800 325 COIN 05 2004 Printed in the U S A
7. No Coin Acceptance No power Make sure changer is plugged into Plug changer into vendor vendor Acceptor Check acceptor LED If LED is on Replace acceptor replace acceptor If still no coin acceptance Replace changer s main logic board If still no coin acceptance Replace changer s main power harness If Acceptor LED is off check to see Plug acceptor cable and or chang that acceptor cable and changer er power harness into changer power harness are properly connect main logic board ed to changer s main logic board If still no coin acceptance Replace changer s acceptor logic board If still no coin acceptance Replace changer s main power harness No vend price set Set vend prices see Setting the Vend Price section of this manual No coin acceptance Coin Return Lever Make sure changer is mounted cor Reposition changer and or vendor Rejects percentage of rectly and coin return lever is in prop coin return good coins er position Acceptor is dirty or foreign Check to see that acceptor coin path Clean acceptor and remove any matter in coin accept path is clean and free of matter foreign matter If still rejects good coins Replace acceptor If still rejects good coins Replace changer s main logic board Accepts coins but gives Acceptor Replace acceptor with good acceptor Replace defective acceptor no or erratic credit and test to see if changer functions properly If still no err
8. Quanto mere COINCO QUANTUMPRO FOUR TUBE OPERATION AND SERVICE MANUAL Page 2 TABLE OF CONTENTS Section 1 General Information sisse 4 For Your Becords ee is 4 Payout Configurations 5 F alllGS eee meet dm aed 6 After Unpacking p 6 Coin Capacitv As 6 Specifications 7 Section 2 Installation Installing the Changer asas 8 Section 3 Configuration Single Price S Models M 13 Setting the Vend Price Option Switch 13 amp Logic Changers 14 Filling the Coin Tubes 7 7 14 Float Mode m M 1 5 Setting the Float Mode asna 15 Activating Float Pay Down AE IL p AE 15 Changing the Coin Tubes 16 Rerouting The Goir d ORE 18 Section 4 Maintenance Routine Maltenance ede e 19 Cleaning 19 Removing Replacing Individual Modules 2 0 Clearing Jamie ii 20 Section 5 Troubleshooting Section 6 Exploded Views Dimensional Views eene 23 Parts Section A MP PPP 24 Page 3 SECTION 1 GENERAL INFORMATION Introduction This manual contains information on installing operating and maintaining your COINCO QuantumPro four tube coin changer This man ual is intended for owners route operators and shop level technicians as a primary source of information Taking time to read this manual and becom
9. atic credit Replace changer s main logic board If still no erratic credit Replace changer s main power harness Page 21 SECTION 5 TROUBLESHOOTING go to cashbox Accepted coins always go to the coin tubes Changer credits coins but does not escrow No Payout Page 22 Troubleshooting Guide TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY Accepted coins always to Front cover Acceptor Tube Sensor Board Coin tube gate is in the open position Tube sensor board Coin return lever Acceptor SINGLE PRICE ONLY Switch 9 is ON escrow is inhibited Payout Motor Check front cover for proper installa tion check the mirrors If coin still goes to cashbox replace acceptor with good acceptor and test to see if changer functions properly If coin still goes to cashbox Check the sensor board for loose components Make sure tube sensor board is properly secured to main logic board Check cable from sensor board for damage or improper con nection If coin still goes to cashbox Remove acceptor back cover and check solenoid for free operation Replace tube sensor board with good board and test to see if changer func tions properly If coins still go to tubes Make sure changer is mounted cor rectly and acceptor gate opens when vendor coin return lever is operated Replace acceptor with good acceptor and test to see if changer operates correctly Uninhibit the escrow feature Make s
10. bes Canadian 25 Tubes Quantum For Single Price units Not shown Do Not Use in 704 705 716 For Transformer in Single Price Page 29 SECTION 6 EXPLODED VIEWS QuantumPro Harness and Logic Board Configuration p HARNESS 407621 G MDB HARNESS 407544 G MDB HARNESS CONNECTOR PROTOCOL L HARNESS CONNECTOR G MDB HARNESS 407544 SMALL PLUG LARGE PLUG 2 REQ D G CONNECTOR L CONFIGURATION i iT lo ru 9 d i 9 gs U dus tli uci TO ae on Efit JU O 000 MJ HB CI img lm er fa MTA oe b01 Logic Board Omm 407526 408086 2 n G CONFIGURATION SINGLE PRICE HARNESS 407864 DEX MIS HARNESS G MDB HARNESS 407544 407939 P CONNECTOR PRIMARY TRANSFORMER CONNECTOR BILL VALIDATOR HARNESS DEX MIS HARNESS SINGLE PRICE HARNESS 407866 CONNECTOR CONNECTOR BILL VALIDATOR G MDB CONNECTOP HARNESS CONNECTOR c 1 ta MJ ric DISPLAY 1 konal CONNECTOR t ALAN A
11. ce type and payout configuration of the coin changer The first three letters of the model number indi cate the Country Code USQ United States Quantum CAQ Canadian Quantum The fourth letter indicates the changer model G MDB S Single Price L Logic The first digit of the model number indicates the series of changer 7 700 and the last two digits represent the changer s payout configura tion SECTION 1 GENERAL INFORMATION Payout Tube Configuration Location A B C D 701 1 00 10 05 20 702 25 10 05 25 703 1 00 10 05 1 00 704 25 25 25 25 705 1 00 25 25 1 00 706 05 10 10 05 707 10 10 10 05 708 25 10 10 05 709 25 05 05 25 710 05 05 05 05 711 1 00 10 10 05 712 25 10 05 05 713 25 05 25 25 714 1 00 05 05 25 715 05 10 05 05 716 1 00 25 25 25 717 1 00 10 10 25 718 1 00 10 05 05 719 2 00 05 25 1 00 720 1 00 05 25 25 721 2 00 10 05 1 00 722 2 00 25 25 1 00 723 2 00 10 05 25 724 1 00 05 05 05 725 1 00 05 05 1 00 726 1 00 05 25 1 00 Example 050 8706 United States Quantum MDB 700 series 5 10 10 5 payout CAQ L701 Canadian Quantum Logic 700 series 1 10 5 25 payout NOTE L model changers should only be configured as 701 702 or 708 Page 5 SECTION 1 GENERAL INFORMATION Features The COINCO QuantumPro c
12. coins 1 00 15 16 coins Payout at least two coins from each tube to ver ify tubes are loaded correctly NOTE If your Four Tube coin changer does not have a quarter or dollar payout tube it is best to load one nickel tube and or one dime tube all the way to the top to cover the upper tube sensors rather than filling mulitple similar tubes part way full This will ensure the bill acceptor stays enabled for a longer period of time Example A USQ G710 has four nickel tubes If you are hand loading the payout tubes and do not have enough nickels to completely fill all four tubes load each tube with approximately 15 coins Then with the remaining coins fill at least on nickel tube to the top Page 14 LOADING THROUGH THE ACCEPTOR Hand loading coins directly into the coin tubes and making sure they lay flat is one way to fill the Four Tube changer with coins If you are keeping track of the DEX information for accounting purposes the coins loaded into the tubes need to be counted by the acceptor e For MDB changers use the vending machine controller board s Tube Fill or Coin Fill mode Refer to the vending machine manual for details For Single Price changers use the coin changer s Manual Fill Mode MANUAL FILL MODE Manual fill mode can be used to fill the tubes of the coin changer through the acceptor without accumulating credit and having to vend the credit away The advantage of t
13. er MDB Coin Changer Plug Page10 Selection Switches Digital Display SECTION 2 INSTALLATION L Model Controller Vendor Interface 24V DC 24 VOLTS DC 5V DC AND 5 VOLTS SV RETURN LOGIC SUPPLIES 1 DISPENSE usor DISPENSE lt SETON A REYPRD FL s x m j x acer e ms VENDING MACHINE CONTROLLER CREDIT DISPLAY COIN CHANGER BILL ACCEPTOR USQ L CAQ L PLUG PIN FUNCTION 1 5 VDC Supply Positive 5 VDC Supply Return 3 Send 0 Volts Active 4 Interrupt 0 Volts Active 5 Data 0 Volts Active 6 Accept Enable 0 Volts Active 7 8 9 VEND MOTORS 25 Dispense 0 Volts Active 2 ii 10 Dispense 0 Volts Active 8 05 Dispense 0 Volts Active 10 Not Used 11 Reset 5VDC Active 12 Not Used 13 24 VDC Supply Return 14 1 Dispense 0 Volts Active 13 14 15 15 24 VDC Supply Positive l rectified unfiltered Coin Changer Plug Page 11 SECTION 2 INSTALLATION S Model Controller Vendor Interface AC HOT T AC NEUTRAL EXACT CHANGE AC NEUTRAL VEND AC HOT CARRIER ACCEPT COINS SWITCHES I I l U 1 VEND I I l I I ELECT s Dun s s SWITCHES CONTROL LOGIC USQ S CAQ S COIN CHANGER 1 a NC PIN Z FUNCTION 117 VAC hot 117 VAC neutral Vend Relay normally open NC no connections Exact Change normally open neutral Enable Coin
14. etal debounce rail out of the acceptor You are now able to fully clean the interior coin rail gates and the intermediate cover pay attention to the mirrored surface on the interme diate cover Reassemble the acceptor in the reverse order NOTE When installing the intermediate cover make sure the metal debounce rail is in place and raise the anti stringing door on the accept reject gate before snapping the cover in place Page 19 SECTION 4 Removing Replacing Individual Assemblies ACCEPTOR To remove the acceptor press down on the acceptor latch and pull the top of the acceptor forward and away from the changer housing Unplug the ribbon cable from the changer Raise the acceptor and pull outward until the acceptor clears the housing slots FRONT COVER AND TUBE SHIELD Remove the front cover by swinging the door open to the right Lift the front cover off of the hinges on the changer housing Remove the tube shield off the top of the coin tubes REMOVING THE TUBES The tubes are held in place by 3 sets of tabs that secure it to the payout base To remove the tubes start with the tube on the left side and pull it straight up Working your way to the right remove all four individual tubes REMOVING THE LOGIC BOARD COVER To remove the logic board cover first remove the strain relief bracket and screw Next remove the screw in the lower center portion of the logic board cover Lift the cove
15. hen they will be routed to the cash box Activating the Float Pay Down by pressing inventory buttons A and B simultaneously will pay down any coins above the level you previ ously set After the coins are paid down the acceptor will automatically go into manual fill mode In manual fill mode the acceptor will only route coins to tubes that are below the set level Once the level is reached the coins will be rejected SETTING THE FLOAT MODE The Float Mode for both Float Level and Float Pay Down are set for all four tubes using the acceptor inventory buttons 1 Using Tube Fill Coin Fill or Manual Fill mode fill the four tubes to the float level you want the changer to maintain 2 Press and release the A and D inventory but tons simultaneously The acceptor LED will flash an equal ON and OFF pattern 3 Within two seconds press and release inventory buttons B and C at the same time to store the tube levels and turn the Tube Float Mode ON The acceptor LED will now display a flash pattern of 10 ON and 90 OFF to indicate the levels are set NOTE To turn off the Float Mode repeat steps 2 and 3 ACTIVATING FLOAT PAY DOWN Press and release acceptor inventory buttons A and B simultaneously After the tubes pay down Manual Fill Mode is automatically entered to allow low tubes to be replensihed through the acceptor When the float levels are reached coins are directed to the coin return The changer will aut
16. his is that coins are accounted for in the DEX fields of a Single Price changer To enter the Manual Fill Mode press inventory buttons C and D at the same time The accep tor LED will flash an equal pattern of ON and OFF to indicate the Manual Fill Mode is active Coins inserted through the acceptor will be rout ed to their proper tubes When the upper tube sensor is reached coins will be directed to the cash box or to the next tube of like coins The changer will automatically exit Manual Fill Mode after 45 seconds of no actitivty or if an inventory switch is pressed and released SECTION 3 CONFIGURATION FLOAT MODE Float Mode is used to reduce the number of coins kept in a tube to a level anywhere between the upper and lower tube sensors The Quantum changer supports one of two fac tory programmed Float Mode operations They are Float Level and Float Pay Down FLOAT LEVEL standard on USQ models In Float Level coins are filled to a chosen level betweeen the upper and lower tube sensors Once the Float Level is set coins will only be routed to the tube if a coin was paid out for change Accepted coins normally routed to that tube will be sent to the cash box FLOAT PAY DOWN Optional must be set at the factory In Float Pay Down coins are filled to a chosen level between the upper and lower tube sen sors Once the level is set coins will continue being routed to the tube until the upper sensor is covered t
17. i ronment and number of transactions The coin changer should be kept in its original shipping carton when not in use This will keep the changer clean and offer the best protection for the unit Mainplate and Coil Assembly Quantum e a Hand Loading Door Figure 7 Cleaning The majority of your QuantumPro changer is manufactured from a high quality plastic which should be cleaned with a warm water and mild detergent solution CAUTION Never submerge changer in water NOT use petroleum solvents steel wool scouring pads or metal brushes for cleaning Do not spray any part of the changer with any type of lubricant Since all coins share a common coin ramp heavy usage or a dirty environment can result in dirt build up in the acceptor To clean the coin ramp lift the acceptor gate upward and diago nally to the right Hold the gate to prevent it from snapping back Wipe the exposed coin ramp and inner surfaces with a damp cloth For excessively dirty units use a damp cloth with a mild detergent DO NOT SUBMERGE UNIT IN WATER For more detailed cleaning of the acceptor remove the front cover see Fig 7 by opening the coin tube loading door and wedge your thumb underneath the front cover To remove the cover push out and up Next remove the intermediate cover using a small screwdriver to release tab on the right side of the acceptor Pivot the intermediate cover out towards the left Lift the m
18. ing familiar with this information will help you obtain the best performance from your COINCO QuantumPro four tube coin changer COINCO QuantumPro Changers can accept and validate up to 16 different coins or tokens ranging in diameter from 15 0 to 28 0 mm and 1 07 to 2 40 mm in thickness For the United States USQ models are factory tuned to accept U S nickels dimes quar ters and dollar coins For Canada CAQ models accept U S and Canadian nickels dimes quarters one dollar and Canadian two dollar coins QuantumPro changers are available in the following models ___ G_ __MDB For electronic vending machines using Multi Drop Bus __ S Single Price For electromechani cal vending machines L Logic For use in vending machines with a logic interface Page 4 For Your Records A label indicating the changer s model number and serial number can be found on the side of the coin changer Refer to the model number and serial number whenever you call your Coinco Service Center for information or serv ice The first four digits of the serial number indicate when the unit was built which is also the begin ning of the warranty period The first two digits indicate the week of manufacture the third and fourth digits indicate the year of manufacture For example Serial Number 420307145 would indicate the unit was manufactured in the 42nd week of 2003 The model number indicates the country cur rency interfa
19. oin changer has a modular design for easy service Individual tubes snap in and out for easy cus tomization Coin tubes are clearly marked with coin denomination in bold white numbers Programmable acceptor allows for easy reconfiguration of coin tubes in the field Hinged front cover simplifies tube removal and serviceability Acceptor Park Position allows easy access to the coin tubes Pays change from self loading high capacity change tubes Two motors provide fast accurate payout All models equipped with the MDB protocol Lightweight rugged plastic construction State of the art electronic logic system is designed for reliability and performance Page 6 After Unpacking After unpacking the unit inspect it for any pos sible shipping damage If the unit is damaged notify the shipping company immediately Only the consignee the person or company receiv ing the unit can file a claim against the carrier for shipping damage We recommend that you keep the original carton and packing materials to reuse if you need to transport or ship your changer in the future If the coin changer is being stored or used as a spare always keep it in its shipping carton when not in use This will keep it clean and offer the best protection for the unit Coin Tube Capacity Low Sensor Full Sensor Hand Load Level Level Level US 05 8 78 84 US 10 11 115 123 US 25 9 87 94 US 1 00
20. omatically return to operating mode after 45 seconds of no activity or if any inventory button is pressed and released Page 15 SECTION 3 CONFIGURATION Changing the Coin Tubes REMOVING REPLACING THE TUBES To change the coin tubes see Figure 6 Remove the acceptor and tube shield from the changer housing Next open the front door by gently pulling outward on the left side swinging it open to the right Remove the four inventory tubes one at a time starting from the left side and working to the right by unsnapping the tube using a flat screwdriver in the window in the upper payout base Replace the tube and shim assemblies by inserting the tube s dovetails into the guides in the housing and push down Coin tubes should be arranged in the order specified on page 5 Figure 6 Page 16 SECTION 3 CONFIGURATION TUBES AND SHIMS The coin tubes for your QuantumPro changer are different sizes to accommodate the different diameter coins Each coin tube has a removable color coded shim which adjusts the tube for the coin s thickness For USQ coin changers the COIN TUBE SHIM combinations are as follows COIN TUBE PART SHIM PART TUBE SHIM ASSY 05 7 408161 1 Blue 921462 408192 1 10 10 408161 2 Red 921800 408192 2 25 5 408161 3 Blue 921462 408192 3 1 00 3 408161 7 Lt Gray 921802 408192 5 For CAQ coin changer the COIN TUBE SHIM combination
21. r out REMOVING THE UPPER TUBE SENSOR BOARD Connected to the bottom of the main logic board is the upper tube sensor board To remove the sensor board release the locking tab and gently pull the sensor board out As you pull the sen sor board out hold the main logic board in place and the sensor board will unplug from the main logic board Page 20 REMOVING THE LOGIC BOARD Unplug the remaining harnesses from the main logic board and lift it out of the housing REMOVING THE PAYOUT BASE ASSEMBLY With the harnesses disconnected from the main logic board remove the two screws one on each side from the changer housing Lay the changer on its back and spread the sides of the housing apart Pull up and out on the payout base assembly REMOVING THE CASHBOX CHUTE From the backside of the changer housing remove the tape seal from the cashbox chute Lift the bottom of the chute up and slide the cashbox chute out Clearing Coin Jams Should a coin jam occur in the cash box chute area use the following steps to help dislodge the coins 1 Remove changer from vendor 2 From the backside of the changer housing remove the tape seal from the cashbox chute Lift the bottom of the chute up and slide the cashbox chute out 3 Remove any lodged coins 4 Replace the cashbox chute by pressing in and up to snap into place SECTION 5 TROUBLESHOOTING Troubleshooting Guide TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY
22. s are TUBE SHIM COIN TUBE PART SHIM PART ASSY 05 7 408161 1 Blue 921462 408192 1 10 10 408161 2 Red 921800 409192 2 25 6 408161 4 Black 921801 408192 4 1 00 3 408161 7 Lt Gray 921802 408192 5 2 00 3 408161 8 Blue 921462 408192 6 NOTE For CAD units if a 25 tube is installed in the A tube location use tube 5 with a black shim The shims are removed and replaced by sliding them in or out of the bottom of the tube Do not reuse shims Continuous installation and removal can stress the plastic causing the shims to lose their ability to stay firmly in place The shim is installed correctly if its part number is visible looking at the rear of the tube Page 17 SECTION 3 CONFIGURATION Rerouting the Coins Whenever the coin tubes are rearranged the programmable acceptor has to be reconfigured to route accepted coins to either the correct tube or vendor cashbox To reconfigure the acceptor apply power to the QuantumPro changer Press inventory buttons A B and D simulta neously for 2 seconds until the acceptor LED goes out Release the inventory buttons and the LED will flash an alternating pattern of 1 second ON 1 second OFF then 2 seconds ON 2 seconds OFF This indicates the rerouting process is waiting for a coin destination coin tube or cashbox to be selected To select a coin tube press and release its inventory button Once the coin destination
23. tch 12 When to enter Use Correct Change condition ON The changer will use the vend price plus the largest denomination coin accepted U S 1 00 This is the amount of money reported in the tubes to the logic board to shut the correct change light off Example 50 vend price plus 1 00 coin 1 50 OFF The changer uses the factory settings U S 1 00 Canada 2 00 SAVING THE VEND PRICE To save the vend price and option switch setting in the coin changer s memory press and release the Mode Button located above the price switch The Main Logic Board LED and the Use Correct Change light on the vendor will flash once indicating that price was record ed The vend price must be set to an amount greater than zero for the changer to accept coins Note If a Single Price Changer is used in a MDB machine set the vend prices on the machine controller board NOT in the coin changer Page 13 SECTION 3 CONFIGURATION MDB amp Logic Changers SETTING THE VEND PRICE Vend prices for MDB and Logic coin changers are set through the vending machine controller VMC See vending machine manual for details Filling the Coin Tubes HAND LOADING To hand load the coin tubes tilt the coin tube loading door open see Figure 4 page 9 load the four tubes with appropriate coins Make sure all coins lay flat and that each tube is filled at least to the 20 mark 05 15 16 coins 10 23 24 coins 25 18 19
24. umPro 408567 3 PETERS i ntu m NU ILI d pi a Er 20 m on Ta DU o gt ei Poches a cto E Page 26 SECTION 6 EXPLODED VIEWS 296 6 6 408052 921430 1 921442 4 921449 4 921450 2 407684 1 407683 3 408178 1 923387 923144 1 921585 1 901358 921839 2 921768 1 296 8R8 923797 1 923143 1 DESCRIPTION Screw Pan Head 6 3 8 PH Type 25 Harness Assembly amp Tube Sense Board Encoder Gear Gearbox Cover Upper Payout Base Lower Payout Base Motor Harness Assembly Sweeper Assembly Coin Clearing Arm Reduction Gear 34 10 teeth Pinion Gear Gear Shaft Cable Tie 4 Lower Tube Sense Lens Lower Tube Sense Harness Screw Pan Head 8 1 2 Type 25 Motor Retainer Reduction Gear 34 14 Teeth E lt N N N N N N Page 27 SECTION 6 EXPLODED VIEWS QuantumPro Final Assembly Page 28 SECTION 6 EXPLODED VIEWS ITEM 20 PART 407610 9 408567 3 AUSQ7XX ACAQ7XX 407544 4 408086 2 407526 407471 1 407541 407956 4 407956 5 921840 921822 921586 1 921724 1 345 6R11 345 6R8 909729 4 922868 909846 1 341S4R5 408192 1 408192 2 408192 3 408192 4 408192 5 408192 6 921462 921800 921802 921801 922201 923353 407746 4 921804 921668 922391 921464 2 922200 1 921474 923127 2 345 4R12 DESCRIPTION Housing Assy Payout Assembl
25. ure motor wires are properly connected to changer s main logic board If still no payout replace motor with good motor and test to see if changer operates properly Make sure coin is routed to that tube Clean or replace front cover Reprogram acceptor coin routing Replace acceptor Replace tube sensor board Replace changer s main logic board Replace acceptor Replace tube sensor board Replace changer s main logic board Reposition changer and or vendor coin return lever Replace defective acceptor Turn Switch 9 OFF and press the mode switch Plug motor wires into main logic board Replace defective payout motor SECTION 6 EXPLODED VIEWS QuantumPro Dimensional View All measurements are shown in inches R 6 81 MAX OPENING Page 23 VIEWS SECTION 6 QuantumPro Acceptor Assembly EXPLODED VIEW FRONT ASSEMBLED VIEW FRONT EXPLODED VIEW BACK Page 24 SECTION 6 EXPLODED VIEWS ITEM O1 Q PART NO 408545 1 906618 906606 2 751S21X 906624 408546 1 408042 922284 1 408153 1 921475 4 921433 1 407954 1 341S4R5 925294 921437 921671 1 921672 921732 3 921427 2 921737 1 921588 921785 921443 2 407615 1 407614 2 922415 407981 908845 1 407613 2 400 8 408041 1 921432 1 925044 925045 925024 921974 345 AR5 925527 1 922283 3 925023 922642 1
26. y Acceptor Assy U S Acceptor Assy CAN Transformer G Logic Board L Logic Board S Logic Board Upper Tube Sense Board Logic Board Cover Logic Board Cover Upper Tube Sense Lens Cashbox Lens Latch Strain Relief Bracket Screw Pan Head 6 11 16 Screw Pan Head 6 1 2 Identification Label Patent Label Configuration Label Screw Flat Head 4 5 16 U S 05 Tube amp Shim Assy U S 10 Tube amp Shim Assy U S 25 Tube amp Shim Assy Can 25 Tube amp Shim Assy U S 1 00 Tube amp Shim Assy Can 2 00 Tube amp Shim Assy Blue Shim Red Shim Light Gray Shim Black Shim Tube A amp B Mirror Tube C amp D Mirror Front Cover amp Mirror Assy Lg Strain Relief Plug Sm Strain Relief Plug Price Setting Label Cashbox Chute Cashbox Mirror Clear Tape 3 4 Tube Shield Screw Pan Head 4 3 4 QTY A Ad c N Lulu NOTES Includes 9 10 27 28 29 QuantumPro QuantumPro XX Payout Configuration QuantumPro XX Payout Configuration For 110V Single Price For Quantum MDB units For Logic Interface units For Single Price units For G amp L models For S models 7 Tube with Blue Shim 10 Tube with Red Shim 5 Tube with Blue Shim 6 Tube with Black Shim 3 Tube with Lt Gray Shim 3 Tube with Blue Shim 05 U S 25 amp CAN 2 00 10 Tubes For 1 00 Tu
Download Pdf Manuals
Related Search