PDF Manual
Contents
1. bit does not pierce the coolant tank on the brake side Step 8 Locate the supplied wire harness On the harness you will see a main 4 wire harness with blue black and brown black wires covered in a black sheath You will also see two 2 wire harnesses wires are all black that each need to be unplugged from the main harness See below for wiring options 1 If you are using a Hogtunes NCA 450 RM to power the lowers the 4 pin male plug on the main harness and plug it into the rear out on the side of the amp Since the front speakers and the lower speakers will work together off the amp make sure the switch on the side of the amp goes to the no fader position 2 If you are using a Hogtunes REV 200 RM to power the lowers the lowers harness will plug into the Amplified Output pigtail on the side of the amp 3 If you are using another brand of amplifier you can cut the 4 pin plug off and wire your amp into our harness The blue black pair is brake side and the black wire is the positive The brown black pair is the clutch side and the black wire is positive 3 Step 9 The balance of the main wire harness will pass through on the brake side of the fairing where the main factory wires pass as shown by A in the image Have the opposite end of the main harness go so it ends up on top of the crash bar as close to the center as you can Locate the 2 wire harness marked brake side and plug it2. into the main harness connector noting it will only go in one way The other side of the same harness will go into the lower Pass the larger connector first You can also tear off the sticker if that makes it easier Once the wires are in the lower take up the slack along the crash bar keeping the main harness as close to the center of the crash bar as possible Step 10 The kit comes with strips of black gummy material Take one of the strips and use it to seal the hole around the wire on the outside of the lower Step 11 Take the Hogtunes front panel and while holding it close the lower snap the arm for the vent back into place on the pivot pin You can now press the front panel onto the lower noting the one clip will snap in and hold the panel in place Re install the 3 factory torx head screws by hand just until they are snug to secure the panel to the lower The bar and 2 nuts removed earlier that secure the top of the lower to the crash bar will now be reinstalled The bolt removed earlier that secures the lower to the bottom of the crash bar is also re installed Step 12 Using some of the supplied zip ties secure the speaker wire to the crash bar keeping the main harness as close to the center of the crash bar as you can It s a good idea to trim the excess of the zip ties as close to flush as possible so there are no sharp edges When done install and secure the painted fairing lower cap with the 7 16 nut removed ear
3. Audio Solutions For The Great American Cruiser D2 F tty y oF Em 4 e fie Ni Na is 4 Any audio system can be a distraction to the rider and or passenger Please use caution when Designed and Engineered in Canada For playing your stereo especially in traffic The Great American Cruiser LC LOWER RM Installation Manual For Use On 2014 Non CVO www hogtunes com Liquid Cooled Touring Bikes Version 1 0 Thank you for choosing the Hogtunes LC LOWER RM Since positive word of mouth is the best way to grow our business we want your new system to work as well as it was designed to If you have any questions or concerns we are here to help Email info hogtunes com or call us during regular business hours EST at 705 719 6361 If you still need help please consider a professional installation by your dealer The LC LOWER RM KIT puts speakers in fairing lowers on 2014 touring bikes with liquid cooled engines only The supplied speakers are 2 Q Ohms Getting Started Step 1 Remove the seat and both wires and from the battery Step 2 Remove the outer fairing headlamp assembly Refer to a service manual if you need help with this Note A towel on the front fender can help prevent scratches or dings from dropped tools or fasteners etc Step 3 See part descriptions in the image below On the speaker panel you will see 4 black screws that need to be removed These screws go into rubber
4. compression nuts that hold the speakers panel to the main lower panel These compression nuts will also come off and be put aside with the screws Compression Nut Main Lower Panel c Speakers Panel Step 4 Starting on the brake side lower fairing use a coin or something similar to carefully pry off the front access cover Look inside the lower opening and at the very back you will see a 7 16 nut that is to be removed This nut allows the painted fairing lower cap on the front to come off With the painted cap off you will see a bar that secures the top half of the lower to the crash bar Remove the 2 nuts and the bar and put aside for now At the bottom of the lower is a clamp that holds the bottom half of the lower to the crash bar Remove the bolt that secures the clamp 362R RM Speaker Specifications Power Handling 125 RMS 200 Peak Frequency Response 55hz 25Khz Sensitivity 92 db 1watt 1meter Nom Impedance 2 Ohms Cool Factor EXTREME Harley Davidson Electra Glide Road Glide Street Glide Ultra Classic Tri Glide CVO Screamin Eagle and Tour Pak are Trademarks and or Registered Trademarks of Harley Davidson Inc Milwaukee Wisconsin USA and if Used or Implied are for Reference Only There is No Affiliation Between Harley Davidson Inc and Hogtunes Inc 6 Step 5 Gently push the top of the lower towards the back of the bike just enough so you can remove the 3 torx screws normally hid
5. den by the painted cap that hold the lowers front panel in place Gently pull on the front panel to release 2 clips which will allow the front panel to come away but not completely free from the bike yet There is asmall arm for the vent mechanism still attached that is removed by squeezing the top of the pivot pin and lifting up on the arm You can now bring the factory lower front panel to a work bench and remove the torx screw that holds the vent adjuster and arm to the factory panel Using the same screw install the vent adjuster and arm into the Hogtunes main lower panel Step 6 The kit comes with die cut foam Foam Panel 4 panels Find the one for the side of the bike Goes Here Jai you are working on and apply as shown Factory noting you should clean the area with White Clip isopropyl alcohol first On your factory Goes Here A front panel you will see 2 white clips One E of these clips will come off and be installed onto the Hogtunes main panel Step 7 Moving to the front side of the lower in the area normally hidden by the painted cap you will see a hole where the bolt passes through that secures the painted cap Just above that hole and approximately 2 back from the bolt hole you will need to drill a 3 8 hole for the wires to pass When this install is finished the painted cap will hide the wire nicely It s a good idea to start with a pilot hole and then drill the final size Use caution to make sure your drill
6. lier Step 13 Take the Hogtunes speaker panel and plug the speaker wires into the speaker noting they will only go on one way and that barbs built into the speaker will lock the connectors in place The rubber compression nuts are now placed into the openings on the main panel and using the screws removed earlier the speaker panel is attached to the main panel Step 14 Repeat the steps to install the lower adaptor for the other side of the bike and when complete turn the radio on to make sure all speakers are working Step 15 Reinstall the wires at the battery and the bikes seat Step 16 Now is the best time to use zip ties to properly secure and clean up any wiring Its always a good idea to remove excess from the zip ties but cutting them as close to flush as possible so there are no sharp edges Before re installing outer fairing turn front wheel to each extreme side making sure any wiring is not impeding the steering of the motorcycle Failure to do so can result in serious injury or death Step 17 With everything working all wires secured and no wires impeding the steering of the motorcycle go ahead and reinstall the outer fairing and your new system is ready to enjoy Adjusting the Bass and Treble The way the system sounds sitting still or at a stop light will be RADICALLY different from how it sounds at speed Use the radios controls to adjust the sound but please do so carefu
7. lly when riding Warranty Information Hogtunes speakers are warranted for a period of 20 years Proof of purchase is required for all warranty claims The warranty applies to the original retail customer and is not transferable Please contact Hogtunes for all warranty claims Products found to be defective during the warranty period will be repaired or replaced with a product deemed to be equivalent at Hogtunes sole discretion Hogtunes complete warranty policy is available at www hogtunes com What Is Not Covered 1 Any expense related to the removal or re installation of Hogtunes products 2 Repairs to these products performed by anyone other than Hogtunes 3 Subsequent damage to any other components 4 Any product purchased from a non authorized Hogtunes dealer 5 Damage to Hogtunes products due to an accident or collision 6 Paint applied to any part for any reason 7 Speaker frames baskets that are bent or broken 8 Speaker cones that are pierced or cut 9 Damage caused by over tightening or not using supplied fasteners 10 Damage from use of Thread lock or Screw Glue materials of any kind
Download Pdf Manuals
Related Search