Home

Here - Polaris

1. Instrument Cluster Setup Set Bottom Screen Menu SERI Trip 1 Distance Display menu to display one of the N following items in ZONE FOUR of SET UNITS 25680 the display screen mi e Trip 1 Distance GAUGE INFORMATION s Wesel ipn Instant Fuel Display Average Fuel SET BRIGHTNESS INSTANT 29 5 Range 25680 mi 1 With SET BOTTOM SCREEN EXIT highlighted on the setup menu Average Fuel Displa press LEFT TOGGLE SET BOTTOM SCREEN iid cladis ied 2 Press RIGHT TOGGLE oo AVERAGE 25 5 repeatedly to cycle through INSTANT FUEL N menu items AVERAGE ce 25680 mi 3 Press LEFT TOGGLE to enter RANGE the desired SET UNITS menu Range Display 4 PressRIGHT TOGGLE to select RANGE 2505 a l EXIT N Press LEFT TOGGLE to exit So SS ii 25680 mi EXIT 45 Instruments Features and Controls Instrument Cluster CHI EFTAI N Instrument Cluster Setup Gauge Information The instrument cluster hardware and software part and serial numbers are displayed on the Gauge Information menu 1 With GAUGE INFORMATION highlighted on the setup menu press LEFT TOGGLE 2 PressRIGHT TOGGLE to select EXIT 3 PressLEFT TOGGLE to exit 46 SETUP SET CLOCK SET UNITS SET BOTTOM SCREEN TPMS SET BRIGHTNESS EXIT GAUGE INFORMATION HW SW HW Ser EXIT Tire Pressure M onitoring System TPM S Setup The TPMS setup menu allows your authorized INDIAN MOTORCYC
2. run when the switch is in the 2 STOP position NA Pressthe bottom of the switch um RUN to complete the circuits ES and allow the engine to start and run Van Tip The headlights and any a accessories plugged into power ports will remain on until the power switch is turned off Audio System Switches See page 143 for audio systems operation Cruise Control Switches Refer to the Cruise Control section of this manual beginning on page 76 for cruise control operation 25 Instruments Features and Controls Switches Engine Starter Switch Read the engine starting procedures before starting the A engine See page 70 Oo The power switch does not have to be on to start the engine o Press and hold the starter switch to engage the one touch starting feature which activates the electrical system and starts the engine The engine stop run S switch must be in the RUN position and the transmission must be in neutral SET DEC Starter Switch Keyless Ignition When the electrical system is activated with either the power switch or the starter switch the key fob must be within range If the key fob is not detected the security light and or power switch will flash The electrical system will automatically shut down The starter motor will not engage during this time If a key fob is not available your personal identification number PIN can be entered using
3. 102 Wheel Installation Front 102 Wheel Spoke Inspection 102 Windshield isins Re RR 52 Windshield Adjustment CHIEFTAIN 52 Windshield Care 121 Windshield Removal CHIEF 52 173 To locate your nearest dealer visit www indianmotorcycle com Indian Motorcycle Company 2100 Hwy 55 Medina MN 55340 Phone 877 204 3697 Part No 9925048 Rev 01 Printed in USA
4. Indicator Lamps Lamp Indicates Condition n Low Battery This lamp illuminates when battery voltage is low Turn non essential accessories off to conserve power Make 3 Voltage sure the charging system is operating properly See page 119 This lamp also illuminates with the security light and or power switch when the key fob battery is low and with the TPMS lamp when the TPMS sensor battery is low W Cruise Control Status Amber Lamp Cruise control is enabled but not set Green Lamp Cruise control is set to the desired speed Read the safety and operation procedures before using cruise control See page 76 ABS Not Activated The indicator remains on until the anti lock system activates which occurs when vehicle speed exceeds 6 MPH 10 km h When the lamp is illuminated the anti lock brakes will not activate but the conventional brake system will continue to operate normally Check Engine This lamp illuminates briefly when the power switch is turned ON This indicates proper function If this lamp illuminates while the engine is running see an authorized dealer promptly The light will remain on if the tilt sensor shuts down the engine If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists Retrieve the error codes for diagnosis See page 40 0 Tire Pressure Monitoring System TPMS The TPMS indicator illuminates if low tire p
5. 7 30 TSF P2 93 7 7 30 75F FM 93 7 151 Audio System Selecting Audio Sources Weather Band WX Weather band channels are broadcast by the National Oceanic and Atmospheric Administration NOAA NOAA operates more than 940 transmitters covering the United States Puerto Rico the U S Virgin Islands the U S Pacific Territories and adjacent coastal waterways 1 Press MODE repeatedly button until WX source is selected Tip Typically only one weather band channel will be available for a given location When traveling if a channel becomes unavailable search for another active channel 2 Press L or gt to select a channel 152 USB Audio Source Connect the USB memory stick to the USB connector cable The following music files are recognized by the radio WAV OGG e MP3 FLAC Music files not recognized by the radio will be ignored 1 Press and release MODE until R USB is active When USB is 7 30 TSF active the console screen will USB display USB as the active ARTIST SONG TITLE 2 Press and hold lt or gt gt to selectthe next or the previous music folder The folders display in alphabetical order 3 Pressand release or gt to select the next or previous song Selecting Audio Sources USB Audio Source iPod iPhone Connected 1 Connect a compatible iPod or iPhone device to the USB connector cable 2 Press and release MODE until 7 30 75F
6. Place the transmission in neutral Press and hold LEFT TOGGLE and RIGHT TOGGLE simultaneously until the SETUP menu appears on the display Press RIGHT TOGGLE repeatedly to cycle through the setup menu Press LEFT TOGGLE to enter the desired menu Instruments Features and Controls Setting the Clock 1 With SET CLOCK highlighted on the setup menu press LEFT SET TIME TOGGLE 2 Press LEFT TOGGLE repeatedly to set the hours 3 Press RIGHT TOGGLE to move to 9830 tens of minutes 4 Press LEFT TOGGLE repeatedly to set the tens of minutes 5 Press RIGHT TOGGLE to move to EXIT minutes 6 Press LEFT TOGGLE repeatedly to set the minutes 7 Press RIGHT TOGGLE to enter the time and move to EXIT 8 Press LEFT TOGGLE to exit 41 Instruments Features and Controls Instrument Cluster CHI EFTAI N Instrument Cluster Setup Set Units Use the SET UNITS menu to set the following items 42 DISTANCE Miles or kilometers VOLUME Gallon Imperial Gallon or Liter TEMPERATURE Fahrenheit or Celsius CLOCK TYPE 12 hour or 24 hour PRESSURE PSI or kPa With SET UNITS highlighted on the setup menu press LEFT TOGGLE Press RIGHT TOGGLE repeatedly to cycle through menu items Press LEFT TOGGLE to enter the desired SET UNITS menu SETUP SET CLOCK SET BOTTOM SCREEN GAUGE INFORMATION TPMS SET BRIGHTNESS EXIT SET UNITS DISTANCE VOLUME TEMPERATURE
7. 7 Wipe away any fluid spills Check for signs of brake fluid leaks around hoses fittings reservoir and brake calipers Front Brake Lever I 2 See page 55 for front brake lever reach adjustments Lubricate the pivot pin and brake lever hinge points at the intervals recommended in the periodic maintenance table beginning on page 82 Also lubricate any time binding is evident Use all purpose grease Inspect brake pads as outlined on page 100 Pivot Pin Front Brake Fluid Change the brake fluid at the intervals recommended in the periodic maintenance table beginning on page 82 Do not attempt to change the anti lock brake system fluid Please see your dealer for this service Always add brake fluid from anew unopened container Always use the recommended fluid See page 128 1 Position the motorcycle on level ground in the fully upright position Position the handlebars so thatthe fluid reservoir is level Wipe the fluid container and the area around the reservoir cover with a clean cloth Maintenance If the fluid level is low inspect brake pads as outlined on page 100 If pads are not worn beyond the service limit inspect the brake system for leaks To add fluid remove Sight Minimum the reservoir cover Glass iS Level Mark screws Remove the gt cover and diaphragm The fluid level should be above the minimum indicator mark in the sight glass Add brake fluid as needed Do not ov
8. Fastener Inspection 1 Inspect the entire motorcycle chassis and engine for loose damaged or missing fasteners Tighten loose fasteners to the proper torque See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer 2 Always replace stripped damaged or broken fasteners before riding Use genuine INDIAN MOTORCYCLE fasteners of equal size and strength Fastener Torques Some procedures and fastener torques are not listed in this manual See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Troubleshooti ng Maintenance For your personal safety do not attempt inspection or repairs notfully described inthis rider s manual Contact an authorized dealer for service if you cannot determine the cause of a problem or if the inspection repair exceeds your mechanical ability or tool resources Do not perform any inspection or repair with the engine running Engine Cranks But Will Not Start Possible Cause Possible Remedy Action Low Fuel Verify fuel level Fuel Pump Inoperative Turn engine STOP switch to RUN Turn the power switch on The fuel pump should run momentarily and then stop Check the fuel pump ignition circuit breaker See page 113 Battery Voltage Too Low Fully charge the battery See page 112 Spark Plug s Fouled Inspect spark plugs See page 105 Spark Plug Wire s Disconnected or Loose Be sure spark plug wires are securely
9. Fuel Systeny Throttle Body Bore Closed Loop Fuel Injection 54 mm Exhaust System 1 into 2 with Catalytic Converter Rev Limit 5400 RPM Idle RPM 800 50 RPM Fully Warm Lubrication System Semi Dry Sump Spark Plug Gap NGK DCPRS8E 034 inch 0 90 mm Chassis Front Suspension Type Travel Telescopic Fork 4 68 in 11 9 cm Telescopic Fork 4 68 in 11 9 cm Front Fork Tube Diameter 46 mm 46 mm Rear Suspension Type Travel Single Shock 94mm Single Shock 114mm Swingarm Cast Aluminum Front Brakes Dual Floating Rotor Rear Brakes Caliper Floating Rotor 125 Specifications Model Year 2014 CHIEF CHIEFTAIN Drive System Primary Drive Gear Drive Wet Clutch Crank Gear 55 Teeth Clutch Gear 86 Teeth Clutch Type Wet Multi Plate Primary Reduction Ratio 1 564 1 Transmission Type 6 Speed Constant Mesh Foot Shift 1st Gear Ratio 2 733 1 2nd Gear Ratio 1 864 1 3rd Gear Ratio 1 385 1 4th Gear Ratio 1 103 1 5th Gear Ratio 0 943 1 6th Gear Ratio 0 811 1 Gear Shift Pattern 1 Down 5 Up Final Drive Type Belt Drive 152 Tooth Transmission 30 Tooth Rear Wheel 66 Tooth Ratio 2 2 1 Overall Gear Ratio 1st Gear 9 403 1 2nd Gear 6 411 1 3rd Gear 4 763 1 4th Gear 3 796 1 5th Gear 3 243 1 6th Gear 2 789 1 126 Specifications Model Year 20
10. Lubricate control cable ends at the intervals recommended in the periodic maintenance table beginning on page 82 NOTICE External casings are factory lubricated Additional lubrication could be detrimental to cable performance Verify proper routing and smooth movement Inspect for damage to the external casing and inspect exposed cable wire for fraying kinks or corrosion Replace any damaged sticky or sluggish cable 1 Disconnect the cable at the clutch lever and at the primary cover 2 Lubricate the barrel ends with all purpose grease 3 Reconnectthe cable and adjust freeplay as needed Rear Brake Pedal 1 Lubricate the pivot bushing at the intervals recommended in the periodic maintenance table beginning on page 82 Also lubricate any time binding is evident Use all purpose grease 2 Inspect brake pads as outlined on page 100 Brake Hoses Connections Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid Tighten any leaking connections and replace components as necessary See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Maintenance Brake Fluid Precautions A WARNING Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death Use only DOT 4 brake fluid from a sealed container Do not operate the front brake with the reserv
11. WARNING Accelerating abruptly could cause your body to shift rearward suddenly which could result in loss of control Accelerating abruptly could also cause loss of control on low traction surfaces Loss of control could result in serious injury or death Always accelerate gradually especially on wet slippery or other low traction surfaces Stopping the Engine Before stopping the engine bring the motorcycle to a complete stop Shift to neutral or disengage the clutch WARNING Stopping the engine with the transmission in gear while the motorcycle is moving could cause loss of rear wheel traction or engine and transmission damage which could cause loss of control and serious injury or death Always stop the engine after the motorcycle is fully stopped and the transmission is in neutral If the engine stops unexpectedly while the motorcycle is moving guide the motorcycle to a safe location off the road and away from traffic Turn the power switch off 1 When fully stopped shift into neutral 2 Move the engine stop run switch to the STOP position 3 Turn the power switch off 75 Operation Using Cruise Control The cruise control switches are located on the right handlebar Read this section and understand how to safely operate this feature before using the cruise control Resume Accelerate Switch RES7ACC 9 SET DEC Set Decelerate Switch Switch WARNING Improper operation of c
12. Driver When a device is paired and connected to the Driver Device location selecting this mode will stream music to the radio When Driver Device is turned on NO AUDIO will be displayed as the radio resumes connection with the device When a device is paired but not connected to a BT source location NOT FOUND will be displayed 7 30 75F GARY S IPOD 7 30 75F DROID RAZR NO AUDIO 7 30 TSF NOT FOUND BT DRIVE DEVICE When a device is paired to a BT source and is in the process of connecting to the radio CONNECTING will be displayed SEARCHING will be displayed when the radio is looking for music files on the paired device Audio System 7 30 IPOD CONNECTING 75F 7 30 IPOD SEARCHING 75F 157 Audio System Voice Recognition M ode The radio features voice recognition when a driver headset is connected and turned on Radio Bluetooth functionality is dependenton the capabilities of the device Please see your device s user manual Tip Make sure the BT volume on your device is turned all the way up The device s signal and battery strength are shown on the display with a range of zero to five 0 5 with 5 representing maximum strength Initiating a Phone Call To initiate a phone call double 7 30 75F press SETT to request voice recognition mode DROID RAZR VOICE COMMAND Speak phone commands into microphone Press and
13. MOTORCYCLE dealer INDIAN MOTORCYCLE SHALL NOT BE LIABLE FORANY OTHER EXPENSES LOSS OR DAMAGE WHETHER DIRECT INCIDENTAL CONSEQUENTIAL OR EXEMPLARY ARISING IN CONNECTION WITH THE SALE OR USE OF OR INABILITY TO USE THE INDIAN MOTORCYCLE FOR ANY PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF ANY INCI DENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU B NO EXPRESS EMISSION CONTROL SYSTEM WARRANTY IS GIVEN BY INDIAN MOTORCYCLE EXCEPT AS SPECIFICALLY SET FORTH HEREIN ANY EMISSION CONTROL SYSTEM WARRANTY IMPLIED BY LAW INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE IS LIMITED TO THE EXPRESS EMISSION CONTROL SYSTEM WARRANTY TERMS STATED IN THIS WARRANTY THE FOREGOING STATEMENTS OF WARRANTY ARE EXCLUSIVE AND IN LIEU OF ALL OTHER REMEDIES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU C No dealer is authorized to modify this INDIAN MOTORCYCLE Limited Emission Control System Warranty IV Legal Rights THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE V This warranty is in addition to the INDIAN MOTORCYCLE Limited Motorcycle Warranty VI Additional Information Any replacement part that is equivalent in performance and durability may be used in the performance of any maintenance or repairs However INDIAN MOTORCYCLE is not liable for
14. OFF 2 Press and release MODE to move to next selection Audio Output Select Use the audio output select menu to direct the audio output to either the external speakers or headsets Speakers Headsets 1 Press lt or Cj to adjust Audio System 7 30 AUDIO OUT SPEAKERS HEADSETS 75F 2 Press and release MODE to move to the next selection 161 Audio System Audio M ode M enus Bluetooth Setup Tip The Bluetooth setup menu is not available when the motorcycle is moving or when the screen is set to display Diagnostic Trouble Codes DTCs Bluetooth Setup allows the user to pair and unpair the headset and devices 1 To access Bluetooth Setup Press and hold MODE to access the audio menu 2 Press and release MODE until BLUETOOTH SETUP is displayed 3 Press and release PRE to access the Bluetooth Setup Menu options 162 7 30 BLUETOOTH SETUP RANGE 250 25680 mi 75F N Bluetooth Setup Menu The Bluetooth Setup Menu provides the following selections DRIVE H SET Pair unpair driver headset s DRIVE DEVICE Pair unpair driver device s EXIT Exit Bluetooth Setup Menu Press and release lt or c to scroll through the list BT SETUP DRIVE H SET DRIVE DEVICE EXIT Press and release PRE or gt to select an item Audio M ode M enus Bluetooth Setup Menu Bluetooth Setup Notes The Bluetooth Setup M
15. Side Covers Remove the left side cover to access the tool kit shock air fitting if equipped fuse box and diagnostic connector Remove both side covers to access the seat mounting fasteners and the electrical connections for the saddlebags 1 Pull outward at each corner of the side cover to disengage the three darts 2 Remove the side cover from the motorcycle 3 Toreinstall the side cover make sure each rubber grommet is properly positioned Align each dart with the appropriate grommet and press inward firmly to secure each dart 105 Maintenance Seat Removal Remove the seat to access the battery 1 Remove the left side cover to access the tool kit 2 Locate the seat mount brackets under the edge of the driver s seat Remove the seat mount bolt from each side of the seat 3 Remove the rear bracket bolt washer and nylon grommet from the passenger portion of the seat if equipped 4 Liftthe rear of the seat and pull rearward to disengage the front mounting tab of the seat from the frame mount Do not allow the seat mount brackets to contact the rear fender Seat Installation 1 Position the seat by inserting the seat mounting tab from rear to front into the mount on the top of the frame 2 Rotate the rear of the seat downward and position the side mount seat brackets onto the frame Do not allow the seat mount brackets to contact the rear fender 3 Oneachside thread the seat mount bolt through the seat mount br
16. if equipped NOTICE On models equipped with a TPMS the sensors are located 180 fromthe valve stem Use caution when servicing tires To avoid damaging a sensor break the bead at the valve stem then at 90 and 270 fromthe valve stem as required With a TPMS the pressure of each tire can be viewed in the MFD If dashes display instead of a pressure value while traveling above 15 MPH 24 km h the system may not be functioning properly See your dealer for service The TPMS warning indicator will illuminate if low tire pressure is detected Always correct low tire pressure promptly Always inspecttire pressure and condition before each ride See page 61 The TPMS display may indicate an increase in tire pressure while riding a normal occurrence as tires warm up Riding into colder conditions may result in a drop in tire pressure as tires cool down Regardless of conditions low tire pressures should always be corrected promptly 49 Instruments Features and Controls Sidestand The sidestand is equipped with a safety switch that prevents operation of the motorcycle if the sidestand is deployed WARNING An improperly retracted sidestand could contact the ground and cause a loss of control resulting in serious injury or death Always retract the sidestand fully before operating the motorcycle To park the motorcycle swing the end of the sidestand downward and away from the motorcycle until itis fully extended Always turn t
17. 26in 660 mm 26in 660 mm Wheelbase 68 1 in 1730 mm 65 7 in 1668 mm Ground Clearance 5 5 in 140 mm 5 6 in 142 mm Rake frame Trail 29 6 1 in 155 mm 25 5 9 in 150 mm Weight Dry Weight without fuel fluids 778 lbs 354 kg Classic 801 Ibs 364 kg Vintage 815 Ibs 370 kg Wet Weight with fuel fluids 812 Ibs 369 kg Classic 835 Ibs 380 kg Vintage 848 Ibs 385 kg Gross Vehicle Weight Rating GVWR 1260 Ibs 573 kg 1385 Ibs 630 kg Gross Axle Weight Rating GAWR Front 485 Ibs 220 kg Rear 775 Ibs 352 kg Front 500 Ibs 227 kg Rear 885 Ibs 402 kg Maximum Load Capacity riders cargo accessories 448 Ibs 204 kg Classic 425 Ibs 193 kg Vintage 537 Ibs 245 kg 124 Specifications Model Year 2014 CHIEF CHIEFTAIN Capacities Engine Oil 5 5 qts 5 21 with filter at oil change 5 5 qts 5 21 with filter at oil change Fuel 5 5 gal 20 81 5 5 gal 20 81 Fuel Reserve fuel light on 1 0 gal 3 8 1 1 0 gal 3 81 Fork Oil 20 3 oz 599 cc 18 8 oz 557 cc Engine Engine Type ThunderStroke 111 Air Cooled Configuration V Twin Displacement 111 cu in 1811 cc Cooling System Air Oil Cooler Compression Ratio 9 5 1 Valve Train 2 Valves Per Cylinder Hydraulic Lifters Bore and Stroke 3 976 x 4 449 101mm x 113mm
18. 30 75F USB ARTIST SONG TITLE TRIP 1 MI 205 5 HR 3 5 ace 250 6 25680 mi You can modify the items in zone four by changing the settings in the SET BOTTOM SCREEN menu See page 45 Instruments Features and Controls Instrument Cluster CHI EFTAI N Zone Three Information The following items can be displayed in Zone Three on the Trip 1 Hours Distance 330 infotainment display Trip 1 Hours Distance will display the Trip 1 Hours Distance total hours and distance in miles or FM 93 7 e Trip 2 Hours Distance kilometers Fuel Economy 1 Press and hold LEFT TOGGLE to Front Rear Tire Pressure reset Trip 1 hours and distance to E i 205 5 e Engine Hours Oil Life zero Average Speed amp Battery Voltage 2 Press LE FT TOGG LE to cycle to HR 3 5 Expanded Radio Information the Trip 2 display Heated Grip Power Level if equipped Trip 2 Hours Distance wem 200 6 A 25680 mi Diagnostic Trouble Codes DTCs Trip 2 Hours Distance will display the Press LEFT TOGGLE repeatedly to cycle through the Zone total hours and distance in miles or Three displays kilometers 7 30 75F 1 Press and hold LEFT TOGGLE to FM 93 7 reset Trip 2 hours and distance to zero 2 Press LEFT TOGGLE to cycle to Ha oma Fuel Economy display HR 21 2 RANGE 250 25680 mi 6 37 Instruments Features and Controls Instrument Cluster CHI EFTAI N Zone Three Information Fuel
19. Antenna if equipped Side Cover Left Shock Air Fill CHIEFTAIN under cover 12 Volt Outlet CHIEFTAIN Saddlebag Muffler Sidestand CHIFTAIN shown Component Identification CHIEFTAIN shown 19 Component Identification Engine Identification Number The engine number is stamped into the right crankcase beneath the balance shaft cover The engine number is positioned behind the right floorboard with the engine installed in the frame Record the number in the space provided on page 129 20 Component Identification Console 1 Clutch Lever 2 Fuel Gauge CHIEF 7 FrontBrake Lever 3 Instrument Cluster 8 12 Volt Outlet CHIEFTAIN 4 Power Switch Security Light 9 Fuel Cap 5 FrontBrake Master Cylinder 10 Ornamental Cap Do not remove 6 Throttle Control Grip CHIEF n CHIEFTAIN 21 Instruments Features and Controls Switches Flasher H d Engine cn Stop Run Switch High Low Light Switch Left Control Turn Signal Switch CHIEFTAIN Windshield CHIEFTAIN Audio c Switches Control Switches Right Control Switch Cruise Switch On Off Switch RIGHT TOGGLE Switch LEFT TOGGLE Switch Left Control Q OY LA PSs lt i Right Control active on CHIEFTAIN only v J NS 22 Instruments Features and Controls Switches CHIEF CHIEFTAIN Auxiliary p d L
20. Brake Fluid 98 99 l l l R l R l R l R l R Brake Lines Brake Pads 100 l l l l l l l l l l l l Clutch Cable 96 l l L l L l L l L l L A Clutch Lever Mechanical 95 96 L l L l L l L l L l L P Diagnostic Codes l l l l l l l l l l l l Drive Belt Rear 65 87 l l l l l l l R l l l l ind Drive Belt Tension Adjustment l l See dealer or service manual for adjustment at indicated intervals and with each tire change thereafter Electrical Equipment Switches l l l l l l l l l l l l Evaporative Emission Control System if 94 l l l l l l l l l l l l equipped Maintenance Key I Inspect clean adjust correct or replace if necessary P Perform R Replace Rebuild 82 Periodic Maintenance Table Maintenance L Lubricate w proper lubricant Replace at specified interval or annually Replace as specified or every 2 years T 9 F s e eleele elele Component H 8 8 8 8 S 8 8 S 8 S See table key below Page g 2B 2 i is Sg E Ss i N S Sa S m Sec 8 B 8 B 8 8 B 8 8 g aga 8 B R K 8 8 g e 8 Fasteners 116 l l l l l l l l l l l l Front Brake Lever 99 L l L L E E L E ABS Components 101 l l l l l l l l l l l l Front Fork Oil 92 l l l R l l R l l R l Front Fork Axle 92 l l l l l l l l l l l l Fuel System Lines Fittings 94 l l l l
21. CLOCK TYPE PRESSURE EXIT Set Units Distance Setting Use the DISTANCE menu to change the speedometer and distance units Select either miles or kilometers 1 With DISTANCE highlighted in the SET UNITS menu press LEFT TOGGLE 2 PressRIGHT TOGGLE to select miles or kilometers 3 Press LEFT TOGGLE to set the desired setting 4 PressRIGHT TOGGLE to select EXIT 5 PressLEFT TOGGLE to exit SET UNITS DISTANCE VOLUME TEMPERATURE CLOCK TYPE PRESSURE EXIT SET DISTANCE MILES KILOMETERS EXIT Instrument Cluster CHI EFTAI N Instrument Cluster Setup Set Units Volume Settings Use the VOLUME menu to change the instrument cluster volume units Selectgallon imperial gallon or liter 1 With VOLUME highlighted in the SET UNITS menu press LEFT TOGGLE Press RIGHT TOGGLE to select gallon imperial gallon or liter Press LEFT TOGGLE to set the desired setting Press RIGHT TOGGLE to select EXIT Press LEFT TOGGLE to exit SET UNITS DISTANCE TEMPERATURE CLOCK TYPE PRESSURE EXIT SET VOLUME GALLON lt IMPERIAL GALLON LITER EXIT Set Units Temperature Settings Use the TEMPERATURE menu to change the instrument cluster temperature units Select Fahrenheit or Celsius 1 With TEMPERATURE highlighted in the SET UNITS menu press LEFT TOGGLE Press RIGHT TOGGLE to select fahrenheit or Celsius Press LE
22. Controls Instrument Cluster CHI EF Multi Function Display MFD Display Units Standard Metric The display can be changed to display either standard or metric units of measurement Standard Metric Display Display Distance Miles Kilometers Fuel U S Gallons Imperial Liter Liters Gallons Temperature Fahrenheit Celsius Time 12 Hour Clock 24 Hour Clock 1 Turn the ignition off 2 Wait 10 seconds 3 Press and hold the LEFT TOGGLE switch while pressing the power switch 4 When the display flashes the distance setting tap the LEFT TOGGLE switch to advance to the desired setting 5 Press and hold the LEFT TOGGLE switch to save the setting and advance to the next display option 6 Repeatthe procedure to change remaining display settings 30 Clock Tip The clock must be reset any time the battery has been 1 2 disconnected or discharged Use the LEFT TOGGLE switch to toggle to the odometer display Press and hold the LEFT TOGGLE switch until the hour segment flashes Release the switch With the segment flashing tap the LEFT TOGGLE switch to advance to the desired setting Press and hold the LEFT TOGGLE switch until the next segment flashes Release the switch Repeat steps 3 4 twice to set the 10 minute and 1 minute segments After completing the 1 minute segment step 4 will save the new settings and exittne clock mode Instrument Cluster CHI EF Multi Functio
23. Economy This screen will display the current instant and average miles per gallon MPG or liters per 100 kilometers 1 Press and hold LEFT TOGGLE to reset the average 2 PressLEFT TOGGLE to cycle to the Front Rear Tire Pressure display Front Rear Tire Pressure This screen will display the current front and rear tire pressure in PSI or kPa e Press LEFT TOGGLE to cycle to the Engine Hours Oil Life display 38 7 30 75F FM 93 7 INSTANT 27 5 MPG AVERAGE 34 5 RANGE 250 25680 mi 6 7 30 75F FM 93 7 FRONT 36 1 PS POS REAR 40 2 RANGE 250 25680 mi 6 Engine Hours Oil Life This screen will display the total engine hours accumulated when the engine is running Engine oil life is also displayed The rate at which oil life is reduced to 0 is determined by the following Engine break in period 0 500 miles or 804 km Routine oil change intervals Every 5 000 miles or 8 046 km Tip When engine oil life reaches 0 change the engine oil and filter After changing the engine oil and filter 7 30 75F FM 93 7 2 5 HR ENGINE OIL A 100 RANGE 250 25680 mi 6 1 Press and hold LEFT TOGGLE until the value begins to flash 2 Press and hold LEFT TOGGLE to reset the engine oil life to 10026 3 Press LEFT TOGGLE to display Average Speed Battery Voltage screen Instrument Cluster CHIEFTAIN Zone Three Information Average Speed Battery Voltag
24. Engine Compression Test An engine compression test can be performed to monitor general engine condition See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Exhaust System Inspection Check the exhaust system for stains from leaking exhaust gasses Replace damaged or leaking exhaust gaskets Check all exhaust system fasteners Tighten loose clamps and fasteners Do not overtighten See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Elevating the Motorcycle WARNING Serious injury or death can occur if the motorcycle tips or falls Make sure the motorcycle will nottip or fall while elevated or while on the sidestand Some procedures require raising the motorcycle to remove weight from the component being inspected Elevate the motorcycle by placing a stable flat platform jack or lift mechanism on a firm flat surface and lifting under the engine crankcase The platform should be a minimum of 12 inches 30 cm square DO NOT attempt to lift the motorcycle without proper equipment Always secure the motorcycle properly before lifting so it cannot tip or fall when elevated 116 Road Test Before returning the motorcycle to regular use perform a road test in a safe area Pay special attention to the proper fit and operation of all serviced components Make any corrections or additional adjustments promptly to ensure safe reliable and enjoyable vehicle performance
25. Labels Information 17 Labels Safety sperren 17 Leather Care iroi lien meetes ke 121 Light Switch Auxiliary Lights 27 M Maintenance Break In Maintenance 80 Major Maintenance 80 Periodic Maintenance 81 83 Maintenance for Safety 15 Maintenance Log 141 Maintenance Required 15 Major Maintenance 80 Metric Display 04 30 MFD CHIEFTAIN ene ee ee 36 IMMER ONES ii ee GR e eda e Gene 49 Modifications Vehicle 12 Motorcycle Safety Foundation 6 Multi Function Display MFD CHIEF 29 32 Multi Function Display CHIEFTAIN 36 Oo Oil Change Engine Oil Filter 84 85 Oil Level Engine Oil 60 Oil Recommendation 128 P PAF KUNG ec edo petet iet pe hae EA 78 Parking on aSlope 78 Parking on a Soft Surface 78 Parking the Motorcycle 12 Passenger Carrying Safely 9 Periodic Maintenance 81 83 Power SWITCH wisi ce a ho ae Se 25 Preload Adjustment Rear Shock CHIEF 89 Preload Inspection Rear Shock 88 R Rear Axle Inspection 91 Refueling Safety Lss 14 Ride Height Adjustment CHIEF 89 Ride Height Adjustment CHIEFTAN 90 91 Ride Height Inspection 88 Riding Safety i ite teste date ded 6 10 Road Testing secasses
26. PRE or MODE to send the incoming call to voice mail If you attemptto initiate a phone call but you do not have your headsets connected HEADSET NOT CONNECTED displays 7 30 75F DROID RAZR 123 456 7890 INCOMING CALL CANNOT ANSWER DRIVER HEADSET NOT CONNECTED 7 30 75F DROID RAZR VOICE COMMAND ERROR DRIVER HEADSET NOT CONNECTED Audio System Siri Eyes Free Your radio s voice command mode supports the Siri Eyes Free feature on select iPhone models so you can use Siri without having to look at the screen For example Play songs by Get directions to Read my notifications Send a message to For additional commands consult your device s owner s manual Siri is available on iPhone 4S iPhone 5 iPad 3rd and 4th generations iPad mini and iPod touch 5th generation and requires internet access Siri may not be available in all languages or in all areas and features may vary by area Cellular data charges may apply For more information about Siri Eyes Free visit www apple cony ios siri 159 Audio System Audio M ode M enus Entering M ode Menu l Press and hold MODE until the system enters the audio System mode menus 2 Pressand release MODE to cycle through the following menu items shown in order of display Bass Mid Treble Fader Automatic Volume Control AVC Audio Output Select Bluetooth Setup Bluetooth Drive Device NA
27. Rodents ix etit dra scere d 123 Storage Area sss 121 Tire MAHOM sss etes 122 Suspension Inspection Front 65 91 92 Suspension Inspection Rear 65 Swing Arm Inspection 91 Switches iis is cise acai ees 22 27 Audio Switches 25 Auxiliary Light Switch 27 Cruise Control Switches 25 Engine Starter Switch 26 Engine Stop Run Switch 25 Hazard Switch eese Rees 25 High Low Headlight Beam Switch 27 Ignition Light Switch 27 Power Switch secessu 25 Saddlebag L CKr cris rar nse os 26 Toggle Switches 27 T Tachometer CHIEFTAIN 33 Testing After Servicing 80 116 Throttle Control Inspection 95 Throttle Inspection 64 Tires COR IBOD ina eO PEERS 103 Recommended Pressure 104 Recommended Type 104 Replacement 103 Tire Condition ere 61 Tire Pressure ssusuuu 61 Tire Pressure Monitoring System 49 Tire Tread Depth 61 Tread Depth neuere 103 Wheel Inspection 102 Toggle Switches 27 Tone Ring Sensor Inspection ABS 101 Transporting the Motorcycle 14 Troubleshooting 117 119 WwW Washing the Motorcycle 120 Weight Capacity 5 16 Wheel Alignment 102 Wheel Inspection
28. a breathable material to prevent moisture from building up on the motorcycle which can cause oxidation of metal surfaces Cleaning and Storage Removal From Storage 1 Install a fully charged battery 2 Check the oil level If the motorcycle was stored in an area subjectto wide swings in temperature and humidity such as outdoors change the engine oil before starting the engine NOTICE During storage temperature and humidity changes can cause condensation to form in the crankcase and mix with engine oil Running the engine with oil that contains condensation can cause engine damage 3 Inspect the storage area for signs of fluid leaks Identify and perform service to any leaking components 4 Remove any intake or exhaust mesh covers installed for rodent protection 5 Install new spark plugs if necessary 6 Performthe pre ride inspections See page 57 7 Perform a road test See page 116 8 Wash and polish the motorcycle Wax polish or apply protectant to appropriate components 123 Specifications Model Year 2014 CHIEF CHIEFTAIN Dimensions Dimensions and specifications may vary with features options and accessories Overall Length 102 7 in 2609 mm Classic 103 3 in 2625 mm Vintage 101 0in 2565 mm Overall Width 39 8 in 1012 mm 39 8 in 1012 mm Overall Height 49 9 in 1267 mm Classic 60 6 in 1539 mm Vintage 60 2 in 1530 mm Seat Height
29. amp zu E Ve e MANUAL California Proposition 65 Warning This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm vaa MOTORCYCLE 2014 Rider s Manual Indian Chief Classic Indian Chief Vintage Indian Chieftain Copyright 2013 Indian Motorcycle Company All information contained within this publication is based on the latest product information available at the time of publication Product improvements or other changes may resultin differences between this manual and the motorcycle Depictions and or procedures in this publication are intended for reference use only No liability can be accepted for omissions or inaccuracies Indian Motorcycle Company reserves the rightto make changes at any time without notice and without incurring obligation to make the same or similar changes to motorcycles previously built Any reprinting or reuse of the depictions and or procedures contained within whether whole or in part is expressly prohibited INDIAN G INDIAN MOTORCYCLE and CHIEF are registered trademarks of Indian Motorcycle Company CHIEFTAIN is a trademark of Indian Motorcycle Company iPhone G iPod iPod nano and iPod touch amp are trademarks of Apple Inc registered in the U S and other countries The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such
30. as overheating can occur See page 70 e Avoid fast starts with wide open throttle Drive slowly until the engine warms up Avoid running the engine at extremely low RPM in higher gears lugging the engine Drive within the recommended operating speeds and gears See page 68 67 O ion Engine Break In Operating Speeds and Gears Odometer Break in Procedure Miles Km 0 90 0 145 Do not operate for extended periods above 1 3 throttle or at any one throttle position Vary engine speed fre quently 91 300 146 483 Do notoperate for extended periods above 1 2 throttle or at any one throttle position Vary engine speed fre quently 301 500 484 800 Do not operate for extended periods above 3 4 throttle At At Perform the break in maintenance outlined in the maintenance section of this manual Break in maintenance 500 800 should be performed by an authorized INDIAN MOTORCYCLE dealer Break in maintenance must include inspection adjustments fastener tightening and an engine oil and filter change Performing break in mainte nance at the required odometer reading helps ensure peak engine performance minimal exhaust emissions and maximum service life of the engine 68 Fueling Always dismount the motorcycle and refuel on level ground with the sidestand down Review the fuel warnings See page 14 Use only the recommended fuel See page 128 Hold the nozzle while filling Do not rest the weig
31. can cause loss of control Ground clearance is reduced when the motorcycle leans Do notallow components to contact the road surface when leaning the motorcycle in a curve as this could cause loss of control Do not tow a trailer Towing a trailer can make the motorcycle hard to handle Retractthe sidestand fully before riding If the sidestand is not fully retracted it could contact the road surface and cause loss of control To maximize braking effectiveness use the front and rear brakes together Be aware of the following braking facts and practices Therear brake provides 4096 of the motorcycle s stopping power at most Use the front and rear brakes together To avoid skidding apply the brakes gradually when the road is wet or rough or contains loose or other slippery substances If possible avoid applying the brakes while making a turn Motorcycle tires have less traction during turns so braking will increase the possibility of skidding Bring the motorcycle to the upright position before applying the brakes With new pads and rotors allow up to 250 miles 500 km of operation in urban driving conditions not highway cruising to allow pads to mate with new rotors Brakes should be used frequently During this time brake performance will be less effective Avoid using brakes harshly unless in an emergency Brake efficiency will gradually increase during this seating period Anti Lock Brake System
32. each new 2014 and later INDIAN motorcycle that includes as standard equipment a headlight taillight and stoplight and is street legal A isdesigned built and equipped so as to conform at the time of initial retail purchases with all applicable regulations of the United States Environmental Protection Agency and the California Air Resources Board and B isfree from defects in material and workmanship which cause such motorcycle to fail to conform with applicable regulations of the United States Environmental Protection Agency or the California Air Resources Board for a period of use depending on the engine displacement of 12 000 kilometers 7 456miles if tne motorcycle s engine displacement is less than 170 cubic centimeters of 18 000 kilometers 11 185 miles if the motorcycle s engine displacement is equal or greater than 170 cubic centimeters but less than 280 cubic centimeters or of 30 000 kilometers 18 641miles if the motorcycle s engine displacementis 280 cubic centimeters or greater or 5 five years fromthe date of initial retail delivery whichever occurs first 137 Warranty Emissions Control System Warranty I Coverage Warranty defects shall be remedied during customary business hours at any authorized INDIAN MOTORCYCLE dealer located within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental Protection Agency and the California Air Resources Boar
33. error screen displays only when the CHECK ENGINE lightis on and only during the current ignition cycle DTCs will reappear only if the fault reoccurs after restarting the engine 40 7 30 75F FM 93 7 DTC SPN 598 FMI 2 ies 2650 6 25680 mi Retrieving Error Codes Ifthe CHECK ENGINE indicator illuminates you can retrieve the error codes fromthe DTC display 1 Press and hold LEFT TOGGLE to enter the display screen Tip The CHECK ENGINE icon will appear on the screen when in the DTC display mode 2 Press LEFT TOGGLE to cycle through the list of available codes 3 Record the SPN and FMI numbers 4 Seean authorized INDIAN MOTORCYCLE dealer for code details and diagnosis 5 Press and hold LEFT TOGGLE to exit 7 30 FM SPN FMI RANGE 75F 93 7 DTC C 7 250 25680 mi 6 Instrument Cluster CHIEFTAIN Instrument Cluster Setup The instrument cluster setup menus allow the following actions Set clock Set units volume temperature clock type pressure Set bottom screen display trip 1 distance instant fuel economy average fuel economy and range View instrument cluster software hardware information Set Tire Pressure Monitoring System TPMS dealer only Adjust infotainment display brightness SETUP SET UNITS SET BOTTOM SCREEN GAUGE INFORMATION TPMS SET BRIGHTNESS EXIT To access the instrument cluster setup menus 1 2
34. gt itis reached SKIP LIMIT REACHED displays 7 Press and release PRE to bring up the station list Use lt or c to scro Il through the list and then press PRE or gt to select a new station 8 Pressand hold PR E to selecta iTunes category or to selecta different channel 7 30 75F 9 Press lt or cT to scroll through the list PANDORA 10 Press and release PRE or gt gt i SKIP TRACK to make a selection 7 30 75F SONG TITLE 11 When Pandora is selected a SMOOTH JAZZ list of available channels is 90 S POP 7 30 75F displayed CLASSIC ROCK PANDORA 12 Press qj or cT to scroll SKIP LIMIT through the list REACHED 13 Press and release PRE or gt gt to make a selection 7 30 75F PANDORA ARTIST SONG TITLE 7 30 for CATEGORY ALBUM PANDORA ARTIST PLAYLIST 155 Audio System Selecting Audio Sources NAV Source Please read this manual and the GARMIN ZUMO 660 NAV MP3 information provided with your player to become familiar with all unit features and operation The audio integration kit must be installed to enable outputs from the NAV MP3 such as navigation instructions or user loaded MP3 media files to play through the headsets or speakers The unitis fully functional witnoutthe kitinstalled but there will be no interface with the vehicle s audio system 156 Navigation MP3 Operation Tips e Signals coming fro
35. iPhone Device Compatibility Your radio will connect with tne following iPod and iPhone models Update your iPod and iPhone devices to the latest software before use Made for iPhone 5 iPod touch 3rd generation iPhone 4S iPod touch 2nd generation e iPhone 4 iPod nano 7th generation iPhone 3GS iPod nano 6th generation iPhone 3G iPod nano 5th generation iPod touch 5th generation iPod nano 4th generation iPod touch 4th generation Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod or iPhone may affect wireless performance 143 Audio System Audio System Introduction Radio Frequencies North America AM 520 to 1720 kHz FM 87 9 to 107 9 MHz WX 7 Channels Europe FM 87 5 to 108 00 MHz MW 531 to 1602 kHz LW 153 to 279 kHz North America Sources FM AM WX USB NAV BT urope Europe 50 Sources FM MW LW USB NAV BT 144 Japan Taiwan Sources FM AM USB NAV BT Australia Sources FM AM USB NAV BT Audio Menu Options Bass Mid Treble Fader Automatic Volume Control AVC Audio Output Bluetooth BT Setup Driver Dev
36. iPod is the active source When iPod is active the console a screen will display iPod as the active source SONG TITLE Tuning FF RW 1 Press and release or gt to select the next or previous song 2 Press and hold or gt to fast forward or rewind Direct Song Selection 1 Press and release PRE to display currently playing track list 2 Press and release lt 4 or cT to scroll track list 3 Press and release PRE or gt gt to select the new song choice and exit to active source display 4 Press lt to exit without selecting a new song track Audio System Category Select 1 Press and hold PRE until the category list appears 7 30 75F Tip Pandora will appear only if device is CATEGORY connected via USB and is capable of PLAYLIST running Pandora ARTIST 2 Tonavigate the categories press ALBUM PANDORA and release lt or c Press and hold to continuously scroll through the list 3 Press and release PRE or gt to select new category 4 Press and release MODE to exit to the main menu 5 To navigate from the category z menu to the sub category menu 7 30 75F press PRE or gt gt ALTERNATIVE CLASSIC ROCK 6 Pressand release lt or cl to gos MUSIC scroll 7 Press and release PRE to select new subcategory and play the first song found Press gt gt to browse the list of songs available 8 Press e to navigate back to the subcategory or category s
37. is dks nbn etis ttr cas 110 Safety Warnings 110 Brake Fluid Level Front Brake 62 Brake Fluid Level Rear Brake 63 Brake Fluid Front Brake 99 Brake Fluid Rear Brake 98 Brake Lever Inspection 62 Brake Lever Front Brakes 55 99 Brake Line Inspection 63 Brake Pad Inspection 100 101 Brake Pedal Inspection 62 B Brake Pedal Lubrication 97 Brake Pedal Rear Brakes 55 Brakes ABS Tone Ring Sensor Inspection 101 Anti Lock Brake System 53 54 Brake Fluid Precautions 97 Brake Lever Inspection 62 Brake Line Inspection 63 Brake Pad Inspection 100 101 Brake Pedal Inspection 62 Disc Inspection Cleaning 100 Front Brake Fluid 62 99 Front Brake Lever 55 99 Hoses Connections 97 Lubricator 5 55 rnc 97 Rear Brake Fluid 63 98 Rear Brake Pedal 55 Broki ice uae hx aaie Roe cce ens 75 Break In Maintenance 80 Break in Procedure 68 Break In Engine 67 68 Breather Hose Inspection 93 Cc Cargo Distribution iry ayes sere 13 Cargo Saleby xn dee rk e 13 Check Engine Indicator CHIEF 31 Cleaning Products etae en Las 120 Clock Resetting iiien iar alee a 30 Clutch Cable Lubrication Mechan
38. l l l l l l l l Fuel Filter 85 R Gear Shift Lever l l l l l l l l l l l l Headlamp 107 l l l l l l l 5 Rear Suspension Rocker l l l l L l l L l l L l amp Rear Shock Unit 65 88 l l l l l l l l l l R S Rear Wheel Alignment 102 l l l l l l l l l l l l Rear Brake Pedal 97 l l l l l l l l l l l l Road Test 116 P P P P P P P P P P P P Sidestand Sidestand Safety Switch 6695 L l L l l l l l l l l l Steering Bearings 93 l l l l l l l l l l l l Suspension Linkage Rear l l l l l l l l l l l l Swingarm Rear Axle 91 l l l l l l l l l l l l Throttle Body l l l l l l l l l l l l Throttle Control Grip L l E L L ja E Tires Wheels Spokes 102 104 l l l l l l l l l l l Maintenance Key I Inspect clean adjust correct or replace if necessary P Perform R Replace Rebuild 83 Maintenance Engine Oil Filter Change Change the engine oil atthe intervals specified in the periodic maintenance table beginning on page 82 Change the oil more frequently if the motorcycle is subjected to Severe use especially operation in cold weather See page 81 NOTICE Failure to perform frequent oil changes during cold weather operation can result in condensation forming Freezing condensation can result in plugged oil lines and serious engine damage The total amount of oil required for the oil and filter change is approximately 5 5 qts 5 2 1 Follow all instructions carefully Do not over
39. lt or gt gt to return to the RADIO OFF screen 170 Audio Compliance Information FCC and Industry Canada Compliance Statement This equipment complies witn FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body This device complies with Industry Canada license exempt RSS standard s Operation is subjectto the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Japan Compliance Statement This device contains a radio module with certification number E T 209 J00052 A About the Rider s Manual 5 ABS leiliniuesi ie sits whine hentai dn Rhone 53 54 ABS Tone Ring Sensor Inspection 101 ABS How to Respond lisse 8 Accelerating fi saaa endete eere 75 Accessories Safety Considerations 11 Air FIEC chen anoche rene tue 86 Anti Lock Brake System 53 54 Anti Lock Brake System Response 8 Apparel for Riding 10 Audio ModeMenus 160 167 Audio Source Selection 149 157 Audio Switches 0000008 25 Audio System sus 143 146 Audio System Diagnostics 168 170 B B CHARQWIAG 4559 2 co bx eme 112 l ristallatiori idem 111 REMOVAL
40. proof of residence Upon residence verification the servicing dealer will be authorized to performthe warranty repair If you move If you move to another country be sure to contact INDIAN MOTORCYCLE Customer Assistance and the customs department of the destination country before you move Vehicle importation rules vary considerably from country to country You may be required to present documentation of your move to INDIAN MOTORCYCLE in order to continue your warranty coverage You may also be required to obtain documentation from INDIAN MOTORCYCLE in order to register your motorcycle in your new country You should warranty register your motorcycle at a local INDIAN MOTORCYCLE dealer in your new country immediately after you move to continue your warranty coverage and to ensure that you receive information and notices regarding your motorcycle If you purchase from a private party If you purchase an INDIAN motorcycle from a private party to be kept and used outside of the country in which the motorcycle was originally purchased all warranty coverage will be denied You must nonetheless register your motorcycle under your name and address with a local INDIAN MOTORCYCLE dealer in your country to ensure that you receive safety information and notices regarding your motorcycle 133 Warranty INDIAN MOTORCYCLE Warranty Policy EXPORTED VEHICLES EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW THERE IS NO WARRANTY OR SERVICE BULLETIN COVERAGE ON THIS VE
41. recommended oil may cause engine damage We recommend the use of INDIAN MOTORCYCLE engine oil 2 Damage or failure resulting from the use of non recommended lubricants or fluids is not covered by this warranty This warranty provides no coverage for personal loss or expense including mileage transportation costs hotels meals shipping or handling fees motorcycle pick up or delivery replacement rentals loss of vehicle use loss of profits or loss of vacation or personal time THE EXCLUSIVE REMEDY FOR BREACH OF THISWARRANTY SHALL BE AT INDIAN MOTORCYCLE SOPTION REPAIR OR REPLACEMENT OF ANY DEFECTIVE MATERIALS COMPONENTS OR PRODUCTS THE REMEDIES SET FORTH IN THISWARRANTY ARE THE ONLY REMEDIESAVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY INDIAN MOTORCYCLE SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION WHETHER ARISING OUT OF EXPRESSOR IMPLIED WARRANTY OR ANY OTHER CONTRACT NEGLIGENCE OR OTHER TORT OR OTHERWISE THIS EXCLUSION OF CONSEQUENTAL INCIDENTAL AND SPECIAL DAMAGESISINDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITSESSENTIAL PURPOSE THE IMPLIED WARRANTY OF FITNESSFOR A PARTICULAR PURPOSE ISEXCLUDED FROM THISLIMITED WARRANTY ALL OTHER IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY ARE LIMITED IN DURATION TO THE ABOVE 12 MONTH WARRANTY PERIOD INDIAN MOTORCYCLE DISCLAIMSALL EXPRESS W
42. release PRE or double press gf pTr while in voice recognition mode to re ACTIVATE PRESET CANCEL MODE SIGNAL 5 BATT 5 send or resume voice recognition request When the phone call is initiated DIALING and either the caller ID Full screen mode shown or OUTGOING CALL will be 7 30 75F displayed DROID RAZR Press MODE to cancel outgoing call OUTGOING CALL if desired DIALING 158 When the call is answered the screen will display CONNECTED Press and release MODE to end the phone call Receiving Answering Phone Calls When a phone is paired to DRIVER DEVICE the audio system will allow the driver to either answer or reject an incoming phone call When an incoming phone call is received the screen will display the information of the caller Press PRE to answer the call Press MODE to reject the call To end the phone call press MODE 7 30 DROID RAZR 123 456 7890 CONNECTED 75F END CALL MODE SIGNAL 5 BATT 5 Full screen mode shown 7 30 75F SCOTT PHONE 123 456 7890 OR CALLID INCOMING CALL ANSWER PRESET REJECT MODE SIGNAL 5 BATT 5 Full screen mode shown 7 30 75F SCOTT PHONE 123 456 7890 CONNECTED Voice Recognition M ode Error Messages If your phone receives an incoming call but you do not have your headsets connected the incoming call information and CANNOT ANSWER displays Press
43. side of motorcycle Inspect the air filter often if riding in unusually wet or dusty conditions Replace the filter at the intervals specified in the periodic maintenance table beginning on page 82 1 Removethethree air box Cover screws and washers Remove the cover 2 Remove the three air filter screws and remove the air filter assembly 3 Remove the air filter 4 Clean the filter sealing surface on the backing plate 5 Verify that the air box cover seal is properly seated in the groove around the outer edge of the air box backing plate 6 Position the air filter assembly against the air box backing plate External Cover Step 5 Air Filter 86 7 Reinstall the three screws Torque to specification Torque 5ft Ibs 7 Nm 8 Reinstall the external air box cover and screws Torque to specification Torque 7 4 ft lbs 10 Nm NOTICE A loose fitting cover or improperly installed filter element may allow debris to enter the engine which may cause premature engine wear Rear Drive Belt Cleaning Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise Clean the belt at every tire change Clean the belt more often if riding in dirty dusty or high debris environments 1 Mix afew drops of mild dish soap with a cup of warm water 2 Useasoftnylon brush to clean the belt and sprocket teeth with the soapy water Clean well in corner areas where road debris and b
44. storage area To best preserve tire condition The storage area should have a relatively constant and moderate temperature The storage surface should be free of oil and gasoline The motorcycle should not be near a radiator or other heat source or any type of electric motor 121 Cleaning and Storage Clean and Protect the Motorcycle To prepare the motorcycle for storage begin by cleaning it as outlined beginning on page 120 Wax painted surfaces and polish chromed and other metal surfaces Apply protectant to exposed rubber vinyl and plastic parts Do not apply rubber protectant to the tire tread surfaces Fuel Stabilizer Add fresh fuel to fill the fuel tank and add fuel stabilizer Do not overfill Ride the motorcycle or start and run the engine for 15 minutes in a well ventilated area to distribute the stabilizer throughout the fuel system Tire Inflation Inflate the tires to normal pressure See page 104 Engine Protection Change the engine oil See page 84 122 Battery Care 1 Remove the battery See page 110 2 Clean the battery terminals first with a wire brush to remove any loose deposits 3 Wash the posts and the ends of the battery cables witha solution of one part baking soda to 16 parts water Rinse with clean water and wipe dry 4 Apply athin film of dielectric grease to the posts and cable connectors 5 Clean the outside of the battery with a solution of mild detergent and war
45. the lamp is illuminated the anti lock brakes will not activate but the conventional brake system will continue to operate normally When the anti lock brakes engage during a braking event the rider will feel pulsing at the brake levers Continue to apply steady pressure to the brakes for the best stopping performance If the ABS light does not come on when the key is turned to the ON or PARK position see your authorized INDIAN MOTORCYLE dealer for service 53 Instruments Features and Controls Brakes Anti Lock Brake System ABS 54 If the lamp continues to illuminate after vehicle speed exceeds 6 MPH 10 kmy h the ABS system is not functioning See your INDIAN MOTORCYCLE dealer promptly for service Operating with non recommended tires or improper tire pressure may reduce the effectiveness of the anti lock brake system Always use the recommended size and type of tires specified for your vehicle Always maintain the recommended tire pressure The anti lock brake system will not prevent wheel lockup loss of traction or loss of control under all conditions Always adhere to all safe motorcycle riding practices as recommended Itis not unusual to leave tire marks on the road surface during a hard braking event The anti lock brake system does not compensate for or reduce the risks associated with excessive speed reduced traction on rough uneven or loose surfaces poor judgment improper operation Brakes The front
46. the pre ride inspections you may use products that are potentially hazardous such as oil or brake fluid When using any of these products always follow the instructions and warnings on the product packaging When inspections reveal the need for adjustment replacement or repair refer to the maintenance section of this manual page 79 refer to the INDIAN MOTORCYCLE Service Manual or see your authorized INDIAN MOTORCYCLE dealer 57 Pre Ride Inspections Turn the power switch on and move the stop run switch to RUN before performing the following electrical inspections Turn the power switch off after completing these inspections If inspection of any electrical item reveals component failure repair or replace the component before operating the motorcycle Item Inspection Procedure Electrical Headlamp Move the headlight switch from low beam to high beam to turn the lights on and verify operation of both beams Start the engine Switch to high beam Verify that the high beam indicator comes on and that lamp brightness increases Taillight Brakelight Verify that the taillight and license plate light illuminate Verify that the taillight lamps increase in brightness when the front brake lever is applied and also when the rear brake pedal is applied Turn Signals Move the turn signal switch to the left Verify that front and rear left turn signals flash as well as the correspond ing light on the indicat
47. underinflation Always check and adjust tire pressure when tires are cold Using a good quality pocket style gauge adjust tire pressure to the recommended pressure See page 104 Pre Ride Inspections Tire Condition Inspect the tire sidewalls road contact surface and tread base If inspection reveals cuts punctures cracks or other wear or damage replace the tire before riding Always use the correct size and type of tires specified by INDIAN MOTORCYCLE for your vehicle Tire Tread Depth Measure the tread depth near the center of the tread on both tires See page 103 Replace any tire with a tread depth of less than 1 16 inch 1 6 mm 61 Pre Ride I nspections Front Brake Fluid Level 1 62 Straddle the motorcycle and bring itto the fully upright position Position the handlebars so that the fluid reservoir is level View the fluid level through the sight glass The fluid should be clear Replace cloudy or contaminated fluid The fluid level should be above the minimum indicator mark in the sight glass If the fluid level is low inspect brake pads as outlined on pages 100 101 If pads are not worn beyond the service limit inspect the brake system for leaks Check for signs of brake fluid leaks around hoses fittings reservoir and brake calipers Add brake fluid if necessary See page 99 Sight Glass Minimum Level Mark Front Brake Lever 1 Pull the front brake lever toward the h
48. up to 200 Ibs Loads up to vehicle s 91 kg maximum load capacity Black Tires Front 130 90 B16 73H Dunlop Elite 3 36 psi 248 kPa 36 psi 248 kPa Rear 180 60 R16 80H Dunlop Elite 3 41 psi 283 kPa 41 psi 283 kPa White Wall Tires Front 130 90 B16 67H Dunlop American Elite 36 psi 248 kPa 36 psi 248 kPa Rear 180 65 B16 81H Dunlop American Elite 40 psi 276 kPa 40 psi 276 kPa 104 Spark Plugs Inspect spark plugs after the break in period and every 15 000 miles 24 000 km thereafter Replace spark plugs every 30 000 miles 48 000 km Always replace spark plugs in pairs Spark Plug Specifications NGK DCPR8E 036 inch 9 mm 12 ft lbs 16 3 Nm Spark Plug Type Spark Plug Gap Spark Plug Torque 1 Make sure the engine has cooled to room temperature 2 Turn the power switch off 3 Pull upward on the spark plug boots not the wires to remove the boots CAUTION Wear eye and face protection when using pressurized alr Spark Plugs 036 inch m t 0 9 mm Maintenance 4 To prevent debris from entering the spark plug holes use compressed air to clean the area around the plugs before removing them Tool 12 mm plug socket Tip Both spark plugs should have the same light or medium tan color deposits The electrodes should be square with sharp edges 5 Reinstall the spark plugs or install new plugs 6 Reinstall the spark plug boots
49. 14 CHIEF CHIEFTAIN Wheels And Tires Front Wheel Size Type 3 5 in x 16 in 40 Spoke 3 5 in x 16 in Cast Aluminum Rear Wheel Size Type 5 in x 16 in 40 Spoke 5 in x 16 in Cast Aluminum Front Tire Type Size White 130 90 B16 67H American Elite Black 130 90 B16 73H Dunlop Elite 3 Rear Tire Type Size White 180 65 B16 81H American Elite Black 180 60 R16 80H Dunlop Elite 3 Electrical Alternator 710W 2000 RPM Battery 12 volt 18 amp hour 310 CCA cold cranking amps Sealed Glass Mat Power Points Front 10 amp maximum Rear 10 amp maximum Combined 10 amp maximum Voltage Regulator 14 4 volts 42 amp Lamps all bulbs are 12 volt Headlight H4 12V 60 55W LL Auxiliary Light H8 35W 35W Tail Brake Light Non serviceable LED Turn Signal Non serviceable LED License Plate Non Serviceable LED Front Fender Light Non Serviceable LED Speedometer Non Serviceable LED Indicator Lights Non Serviceable LED 127 Specifications Fuel Recommendation For best performance use only unleaded gasoline with a 91 pump octane minimum R M 2 Method DO NOT USE E 85 GASOLINE ORGASOLINE CONTAINING METHANOL Using E85 or gasoline methanol blends can result in poor starting and driveability engine damage and damage to critical fuel system components Gasoline containing up to 1596 Ethanol can be used Gasoline containing up to 15 Methyl Tertiary Butyl Ether MTB
50. AN MOTORCYCLE s suggested retail price for all warranted parts replaced and labor charges based on INDIAN MOTORCYCLE S recommended time allowance for the warranty repair and the geographically appropriate hourly labor rate The owner may be required to keep receipts and failed parts in order to receive compensation 138 Warranty Emission Control System Warranty II Limitations The Emission Control System Warranty shall not cover any of the following A Repair or replacement required as a result of Accident Misuse Repairs improperly performed or replacements improperly installed Use of replacement parts or accessories not conforming to INDIAN MOTORCYCLE specifications which adversely affect performance and or Use in competitive racing or related events B Inspections replacement of parts and other services and adjustments necessary for required maintenance C Any motorcycle on which the odometer mileage has been changed so that actual mileage cannot be readily determined 139 Warranty Emission Control System Warranty III Limited Liability A Theliability of INDIAN MOTORCYCLE under this Emission Control System Warranty is limited solely to the remedying of defects in material or workmanship by an authorized INDIAN MOTORCYCLE dealer atits place of business during customary business hours This warranty does not cover inconvenience or loss of use of the motorcycle or transportation of the motorcycle to or fromthe INDIAN
51. ANTY Indian Motorcycle Company 2100 Highway 55 Medina MN 55340 INDIAN MOTORCYCLE gives a ONE YEAR LIMITED WARRANTY on all components of your INDIAN motorcycle against defects in material or workmanship This warranty covers parts and labor charges for repair or replacement of defective parts and begins on the date of purchase by the original retail purchaser This warranty is transferable to another owner during the warranty period through an INDIAN MOTORCYCLE dealer but any such transfer will not extend the original term of the warranty The duration of this warranty may vary by international region based upon local laws and regulations EXTENDED SERVICE CONTRACT ESC NOT PART OF LIMITED WARRANTY INDIAN MOTORCYCLE provides the original retail purchaser of this INDIAN motorcycle with a 5 year extended service contract ESC that begins at the time of registration The ESC is separate from has different terms and coverage is not a part of and has no effect on the terms coverage or duration of this Limited Warranty Please review those terms and conditions for information regarding the ESC In some circumstances the ESC may not be transferred to a used or second hand purchaser of this INDIAN motorcycle INDIAN MOTORCYCLE makes no representations and disclaims all liability regarding the availability or transferability of the ESC to a used or second hand purchaser REGISTRATION Atthe time of sale the Warranty Registration Form must be comple
52. ARRANTIES NOT STATED IN THISWARRANTY SOME STATES DO NOT PERMIT THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ALLOW LIMITATIONSON THE DURATION OF IMPLIED WARRANTIES SO THE ABOVE LIMITATIONSM AY NOT APPLY TO YOUIF INCONSISTENT WITH CONTROLLING STATE LAW 132 Warranty INDIAN MOTORCYCLE Warranty Policy HOW TO OBTAIN WARRANTY SERVICE If your motorcycle requires warranty service you must take itto an INDIAN MOTORCYCLE Servicing Dealer When requesting warranty service you must present your copy of the Warranty Registration Formto the dealer THE COST OF TRANSPORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY INDIAN MOTORCYCLE suggests that you use your original selling dealer however you may use any INDIAN MOTORCYCLE Servicing Dealer to perform warranty service In the Country where your motorcycle was purchased Warranty or Service Bulletin repairs must be done by an authorized INDIAN MOTORCYCLE dealer If you move or are traveling within the country where your motorcycle was purchased Warranty and Service Bulletin repairs may be requested from any authorized INDIAN MOTORCYCLE dealer Outside the Country where your motorcycle was purchased If you are traveling temporarily outside the country where your motorcycle was purchased you should take your motorcycle to an authorized INDIAN MOTORCYCLE dealer You must show the dealer photo identification from the country of the selling dealer s authorized location as
53. DEVICE ADD DEVICE DROID RAZR ADD DEVICE UNPAIR ALL EXIT 6 um release PRE to ADD DEVICE SEARCHING The radio will search for the device When the device is found its name will display ADD DEVICE 7 Press and release PRE to pair the device with the radio Tip If prompted to enter a pairing code find the code in the headset user s manual Audio System IPOD PAIRING Use lt q or Cj to enter the digits 0 9 Press and release PRE to enter the number and move to the next digit Default codes are typically 0000 or 1234 8 PAIRED is displayed on the screen when the radio has successfully paired the device IPOD PAIRED 165 Audio System Audio M ode Menus Bluetooth Setup M enu Unpairing Reconnecting Devices Tip The following steps reference the DRIVE H SET as an example 1 166 Unpairing other devices follows the same procedures In the Bluetooth Setup Menu use cq or c1 to make a selection Select DRIVE H SET Press and release PRE To unpair ALL of the devices in the DRIVE H SET location press Kh or K to select UNPAIR ALL and then press PRE Press cy or c to select NO or YES Select YES and then press and release PRE to unpair all devices The radio will unpair all of the devices from this location and return to the ADD H SET screen BT SETUP DRIVE DEVICE EXIT DRIVE H SET SCALA RIDER G9 S
54. DIAN MOTORCYCLE dealer or Indian Motorcycle Company To contact NHTSA or obtain other information about motor vehicle safety you may either call the Vehicle Safety Hotline toll free at 1 888 327 4236 TTY 1 800 424 9153 visitthe NHTSA web site at www safercar gov or write to ADMINISTRATOR NHTSA 1200 New Jersey Avenue SE West Building Washington DC 20590 Safety Safety and Information Labels Labels are model specific and market specific Your motorcycle may not contain all of the labels shown 1 Vehicle Identification Number VIN on side of steering head 2 Vehicle Emission Control Information VECI 6 Highway Bar Warning 3 Noise Emission Control Information NECI 7 Shock Air Pressure Warning CHIEFTAIN under side cover 4 Operator Warning Fuel Recommendation 8 Rear Wheel Service Warning if equipped under side cover 5 Saddlebag Cargo Warning 17 Component eeguneguon ROMNAUNARWNE e 18 Rear Brake Pedal Right Front Turn Signal Windshield if equipped Auxiliary Lights Left Front Turn Signal Headlight INDIAN MOTORYCLE War Bonnet Passenger s Foot Peg Driver s Footrest Gear Shifter Speakers Mirror 12 Volt Outlet CHIEFTAIN USB Cord CHIEFTAIN Taillight Right Rear Turn Signal Left Rear Turn Signal Front Fork Fuel Tank Air Box Cover Left Driver s Seat Battery under seat Passenger Seat if equipped Saddlebag if equipped Radio
55. E can be used In the event that the recommended premium unleaded gasoline is not available and low octane fuel must be used fill the fuel tank only partially witn unleaded regular gasoline then fill the tank fully with premium unleaded gasoline as soon as possible 128 Engine Oil Recommendation We recommend the use of INDIAN MOTORYCLE Premium Synthetic Blend 20W 40 Engine Oil for your motorcycle This oil is formulated with synthetic based oil and premium engine additive which have physical properties that meet API SM and ILSAC GF 4 specifications Do not blend oil additives with engine oil If oil mustbe added in an emergency and the recommended oil is not available choose only a high quality 20W 40 motorcycle oil Change back to the recommended oil at the first opportunity NOTICE Use of non recommended lubricants can result in engine damage Damage resulting from the use of non recommended lubricants is not covered by warranty Fork Oil We recommend the use of INDIAN MOTORCYCLE Fork Oil for your motorcycle Brake Fluid We recommend the use of INDIAN MOTORCYCLE DOT 4 Brake Fluid for both brake master cylinders DO NOT use DOT 5silicone fluid Specifications Identification Number Record Record important identification numbers below Vehicle Identification Number VIN see page 17 Engine Identification Number see page 20 129 Warranty INDIAN MOTORCYCLE Warranty Policy LIMITED WARR
56. ENA SMH10 UNPAIR ALL EXIT UNPAIR ALL DRIVE H SET NO DRIVE H SET ADD H SET EXIT To unpair individual devices in the DRIVE H SET location press and release cy or CJ to select the device you want to unpair Press and release PRE to select the device Press and release lt or c to select UNPAIR Push and release PRE to unpair the device UNPAIRED will be displayed after the device is removed from the list The radio will return to the DRIVE H SET device location To connect a different paired device at a location select that device and press PRE to select it Select RECONNECT Press PRE DRIVE H SET SENA SMH10 SCALA RIDER G9 UNPAIR ALL EXIT SCALA RIDER G9 RECONNECT UNPAIR EXIT SCALA RIDER G9 UNPAIRING SCALA RIDER G9 UNPAIRED DRIVE H SET UNPAIR ALL EXIT SCALA RIDER G9 UNPAIR EXIT Audio M ode M enus Bluetooth Driver Device 1 Press qj or Cj to turn the DRIVER BT device source ON or OFF SOURCE ON SOURCE OFF Press and release MODE to move to the next selection NAV Audio 2 1 Press lt or cj to turn the NAV AUDIO source ON or OFF Press and release MODE to move to the next selection Tuner Clear Presets 1 To clear all FM or AM radio station presets press dq or d to select FM or AM clear presets Press PRE to clear the presets for th
57. FM AM MW LW Tuning MW and LW radio sources are in Europe only Press MODE repeatedly to choose the desired audio 1 2 Source Use the tune buttons on the left control to tune radio stations Press and release L or gt to locate stations in single step increments Press and hold L or 7 to seek for radio stations The radio will slew until the tune button is released Atthat time the radio will seek to the next strong radio station signal FM 93 7 7 30 75F 93X ARTIST FM station shown with RBDS FULL on Selecting Audio Sources FM AM MW LW Tuning Memory Presets The audio system features 15 user defined presets for each tuner source for storing favorite stations 1 Toseta preset press MODE repeatedly until the desired source is active FM AM MW LW 2 Use lt or 7 to tune a radio station 3 Pressand hold PRE Press cQ or c to cycle to an available preset location The preset location displays on the screen Tip Saving a radio station without picking a location will save the station in the next available location 5 When the desired location is displayed press PRE 7 30 FoF FM 93 7 P2 6 The station will be stored Tip Ifthe desired preset location already contains a stored radio station it will be overwritten by the new selection 7 Press PRI E repeatedly to scroll through the list of radio presets Audio System
58. FT TOGGLE to set the desired setting Press RIGHT TOGGLE to select EXIT Press LEFT TOGGLE to exit Instruments Features and Controls SET UNITS DISTANCE VOLUME TEMPERATURE CLOCK TYPE PRESSURE EXIT SET TEMPERATURE FAHRENHEIT CELCIUS EXIT 43 Instruments Features and Controls Instrument Cluster CHI EFTAI N Instrument Cluster Setup Set Units Clock Type Use the CLOCK TYPE menu to change the clock format Select 12 hour or 24 hour format 1 Witn CLOCK TYPE highlighted in the SET UNITS menu press LEFT TOGGLE Press RIGHT TOGGLE to select 12 hour or 24 hour Press LEFT TOGGLE to set the desired clock format Press RIGHT TOGGLE to select EXIT Press LEFT TOGGLE to exit SET UNITS DISTANCE VOLUME TEMPERATURE 0K00 SDa PRESSURE EXIT SET CLOCK TYPE Dom 24 HOUR EXIT Set Units Pressure Use the PRESSURE menu to change the pressure display format Select PSI or KPA 1 With PRESSURE highlighted in the SET UNITS menu press LEFT TOGGLE 2 Press RIGHT TOGGLE to select PSI or KPA 3 Press LEFT TOGGLE to setthe desired pressure display format 4 PressRIGHT TOGGLE to select EXIT 5 PressLEFT TOGGLE to exit SET UNITS DISTANCE VOLUME TEMPERATURE CLOCK TYPE PRESSURE EXIT SET PRESSURE i KPA EXIT Instruments Features and Controls Instrument Cluster CHIEFTAIN
59. H SET 5 Press and release PRE 6 Press PRE to select ADD H SET Tip Sena SMH10 motorcycle Bluetooth headsets are recommended Reference the headset user manual to enable Bluetooth pairing The radio will search for the headset 164 BT SETUP DRIVE DEVICE EXIT DRIVE H SET ADD H SET EXIT 7 30 75F ADD HEADSET SEARCHING 7 When the headset is found its name will be displayed 8 Press and release PRE to pair the headset with the radio 9 Theradio will display PAIRING during the pairing process Tip If prompted to enter a pairing code find the code in the headset user s manual 7 30 SENA SMH10 EXIT 75F ADD HEADSET 7 30 SENA SMH10 PAIRING 75F Use qj or cp to enter the digits 0 9 Press and release PRE to enter the number and move to the next digit Default codes are typically 0000 or 1234 PAIRED is displayed on the screen when the radio has successfully paired the headset 7 30 SENA SMH10 PAIRED 75F Audio M ode M enus Bluetooth Setup Menu Driver Device Pairing The radio can be paired with Bluetooth devices such as smart phones l Inthe Bluetooth Setup Menu press cq or c to scroll 2 Setdevice to Discoverable Mode before starting the BT SETUP pairing procedure DRIVE H SET 3 Select DRIVE DEVICE DRIVEDEVICE 4 Pressand release PRE EXIT 5 Use Kj or c to scroll to DRIVE
60. HICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER S AUTHORIZED LOCATION This policy does not apply to vehicles that have received authorization for export from INDIAN MOTORCYCLE Dealers may not give authorization for export You should consult an authorized dealer to determine this vehicle s warranty or service coverage if you have any questions This policy does not apply to vehicles registered to government officials or military personnel on assignment outside the country of the selling dealer s authorized location This policy does not apply to Safety Bulletins NOTICE If your vehicle is registered outside of the country where it was purchased and you have not followed the procedure set above your vehicle will no longer be eligible for warranty or service bulletin coverage of any kind other than safety bulletins Vehicles registered to Government officials or military personnel on assignment outside of the country where the vehicle was purchased will continue to be covered by the Limited Warranty Please work with your dealer to resolve any warranty issues Should your dealer require any additional assistance they will contact the appropriate person at INDIAN MOTORCYCLE This warranty gives you specific legal rights and you may also have other rights which vary from state to state or in different countries If any of the above terms are void because of federal state local law all other warranty terms will remain in effect For
61. LE dealer to register new tire pressure sensors SETUP SET CLOCK SET UNITS SET BOTTOM SCREEN GAUGE INFORMATION SET BRIGHTNESS EXIT Instruments Features and Controls Instrument Cluster CHI EFTAI N Instrument Cluster Setup Set Brightness METHOD 2 SETUP The brightness level of the instrument cluster and display 1 With SET BRIGHTNESS SET CLOCK screen can be adjusted There are two methods to enter the highlighted on the setup menu SET UNITS Set Brightness menu press LEFT TOGGLE MEHODS 2 Press LEFT TOGGLE SET BOTTOM SCREEN repeatedly to adjust the GAUGE INFORMATION This method bypasses the 7 30 75F brightness level from 096 to TPMS instrumentcluster setup menu The 10096 transmission does not have to be in FM 93 7 3 When the desired brightness neutral using this method level is set press RIGHT 1 Press and hold RIGHT TOGGLE to select EXIT EXIT TOGGLE until the SET BRIGHTNESS menu appears 4 Press LEFT TOGGLE to exit 2 Press RIGHT TOGGLE BRIGHTNESS SET BRIGHTNESS repeatedly to adjust the instrument cluster brightness SWA 3 The menu will close after the BRIGHTNESS desired brightness level is set ww 250 6 25680 mi EXIT 47 Instruments Features and Controls Throttle Control Grip The throttle control grip is located on the right handlebar Use the throttle control grip to control engine speed While seated in the proper riding po
62. OKto run but monitor condition Maintenance oe 4 87 Maintenance Rear Shock Preload Ride Height Inspection Periodically inspect rear shock preload For the most comfortable ride and proper ground clearance adjust preload if ride height is out of specification L 2 3 88 Verify that tire pressure is at specification See page 104 Secure the motorcycle in an upright position by clamping the front wheel in a wheel vise Remove the saddlebag if equipped Apply a strip of tape to the rear fender directly over the center of the rear axle Measure Here 5 6 5 10 Using a suitable lift raise the motorcycle until the rear shock is completely extended Measure the distance in millimeters from the center of the rear axle to the bottom of the tape Record the results as measurement M 1 Lower the motorcycle and remove the lift Load the motorcycle with all intended cargo Wearing your riding gear bring the motorcycle to the upright position and sit on the operator s seat If you plan to carry a passenger have the passenger with riding gear sit on the passenger seat Have an assistant measure in the same location Record the results as measurement M2 Subtract measurement M2 from M1 The result is the measured rider sag M1 M2 Sag Adjust preload as needed Adjustment Recommended Suspension Sag Procedure CHIEF 35mm
63. RNING Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and handling and could cause loss of control NEVER exceed the GVWR of your motorcycle The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR This capacity is determined by calculating the difference between your motorcycle s GVWR and wet weight Refer to the Specifications section of this manual page 124 or the Manufacturing Information VIN label on the motorcycle frame for model specific information When determining the weight you will be adding to your motorcycle and to ensure you do not exceed the maximum load capacity include the following operator body weight passenger body weight weight of all riders apparel and items in or on apparel weight of any accessories and their contents weight of any additional cargo on the motorcycle 16 Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to notifying INDIAN MOTORYCLE in writing If NHTSA receives similar complaints it may open an investigation and if itfinds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your IN
64. Response When the anti lock brakes engage during a braking event the rider will feel pulsing attne brake levers Continue to apply steady pressure to the brakes for the best stopping performance Safety Safe Riding Practices Carrying a Passenger Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests To carry a passenger safely Donotexceed the gross vehicle weight rating GVWR for Before riding be sure your passenger knows safe riding your motorcycle Refer to the Specifications section of this procedures Discuss any safety information unfamiliar to manual page 124 or the Manufacturing Information VIN your passenger A passenger who is unaware of safe label on the motorcycle frame for model specific riding procedures may distract you or make movements information that make the motorcycle hard to handle Adjust ride height as needed See pages 89 91 Adjust your riding style to compensate for the differences Directthe passenger to hold onto you or to the passenger in handling acceleration and braking caused by the hand strap with both hands and to keep both feet on the additional weight of the passenger Failure to do so can passenger footrests Do notcarry a passenger who cannot cause loss of control place both feet firmly on the passenger footrests A passenger who is not holding on properly or who cannot reach the passenger footrests can shift their body erratically w
65. See page 89 CHIEFTAIN 45mm See page 90 Maintenance Rear Shock Preload Ride Height Adjustment CHI EF 1 Park the motorcycle with the sidestand down on a firm level surface Remove all riders and cargo 2 Remove the seat See page 106 Tip Using the INDIAN MOTORCYCLE spanner wrench PV 46993 will make rear suspension adjustment significantly easier 3 The upper spanner nut on the shock is the lock nut The lower spanner nutis the adjuster nut Loosen the lock nut by turning it counter clockwise as viewed from the top of shock with tne spanner wrench F Increase 4 Spray alight lubricant on the adjuster nut where it contacts the Preload spring more firm 5 Adjust shock preload by rotating the adjuster clockwise as A viewed from the top of shock to INCREASE preload firm or counter clockwise to DECREASE preload softer 6 Recheck the preload measurement after adjusting Tighten the lock nut securely against the adjuster nut 8 Reinstall the seat N 89 Maintenance Shock Air Pressure Ride Height Adjustment CHIEFTAIN Air Suspension Adjustment For riding comfort and to ensure proper ground clearance adjust rear shock air pressure Refer to the label located on the inside ofthe left side cover The label shows recommended pressures based on potential load weights Always inspect and adjust shock preload ride height based on your actual load weight in addition to a
66. V Audio FM AM Tuner Clear Presets Radio Broadcast Data System RBDS 3 Atthe RBDS screen press and release MODE to return to the beginning of the mode menu list 160 Exiting Mode Menu Exitthe screen and return to the defaultdisplay in one of two Ways 1 Wait 10 seconds The system will automatically exit 2 Press lt or to exit Bass Setting Press lt or c to adjust Press and release MODE to move to next selection Mid Setting Press qj or c to adjust Press and release MODE to move to next selection Treble Setti ng Press qj or cT to adjust Press and release MODE to move to next selection 7 30 15F BASS 6 7 30 75F MID 1 7 30 15F TREBLE 4 Audio M ode M enus Fader Setting 1 Press lt or Cj to adjust speaker fader balance 2 Use the fader adjustment menu to control audio sound balance between front and rear speakers Tip Fader setting menu not shown if headsets are selected as the output 7 30 FADER 0 75F 3 Press and release MODE to move to next selection Automatic Volume Control AVC When set this feature will lower or raise the speaker headset volume automatically based on vehicle speed Off No Adjustment Low Least aggressive setting Medium Moderate setting High Most aggressive setting 1 Press lt or c to adjust the automatic volume settings 7 30 75F AVC HIGH LOW
67. a fuse reinstall the fuse box cover and side cover Fuse Box Cover Clips High Current Fuses The JCASE fuse box contains the high current fuses for the chassis vehicle control module and anti lock brake system This fuse box is located next to the battery box Fuse application and size are provided on a label on the fuse box cover Maintenance JCASEG Fuse Box NN 113 Maintenance Electrical Precauti ons Be aware of the following precautions regarding the electrical system to avoid disruption of electrical signals and possible system malfunction DO use ONLY genuine INDIAN MOTORYCLE parts and accessories designed for your model and follow the instructions provided DO use the accessory power jack provided if equipped If itis necessary to provide power to an item that does not use one ofthe previously mentioned power jacks connect to the load side of the main circuit breaker under the cover behind the oil cooler and connectthe ground wire to the engine ground atthe front left side of the crankcase near the circuit breaker DO NOT splice or cut any wires DO NOT tap in to any power or ground on the motorcycle unless specifically directed to do so by the INDIAN MOTORYCLE instructions that come with the kit DO NOT back probe electrical connectors on the vehicle unless directed to do so by the INDIAN MOTORCYCLE Service Manual DO NOT power any accessories from the diagnostic connector und
68. aa r 80 116 S Saddlebag Lock Switch 26 Saddlebag Removal Hard Bag 51 Saddlebag Removal SoftBag 50 Saddlebadgs docs cce ie 50 51 Saddlebags Using Safely 12 Safety Defects Reporting to NHTSA 16 Safety GaP uis eese sup po doe je e s 10 Safety Symbols ican eee x ccrte 5 Seat Installation Less 106 Seat Removal merapu e5c44 4 6eep RE RS 106 Security System Changing Your PIN 115 Unlocking With PIN 114 Service Manual 00000000 4 Severe Use 0 0 0c 81 Shift POMES rei a ioa eric mede 74 Shifting Gears 55 72 74 Shock Air Pressure CHIEFTAN 90 91 Shock Preload Adjustment CHIEF 89 Shock Preload Inspection 88 Side Covers Removal Installation 105 Sidestaridi us aaia a E al E 50 Sidestand Inspection 66 S Sidestand Lubrication 95 Sigrial Word Sss xau xe dene 5 Spark PI gsS 4 4 ieu deter doe bcd 105 Specifications 124 128 Speedometer CHIEF 28 Speedometer CHIEFTAIN 33 Steering Head Inspection 93 Steering Inspection 65 Storage Battery Care cesse 122 Clean Protectthe Motorcycle 122 Engine Protection 122 Fuel Stabilizer sic edit ieai RR 122 Maintenance During 122 Motorcycle Cover 123 Removal From Ee RR 123
69. acket and into the frame Torque seat bolts to specification Torque 18ftdbs 13 5 Nm 4 Gently raise the rear bracket and reinstall the nylon grommet Thread the rear 106 bracket bolt and washer through the bracket and nylon grommet Torque the boltto specification Torque 96in Ibs 10 8 Nm Rear Bracket Bolt Seat Mount Bolts Seat Mount Bolts Headlight Aim Inspection On high beam the center of highest intensity appearing as a diamond shape should be 7 5 in 19 cm lower than the headlamp bulb and centered straight ahead at 25 feet 7 6 m 1 2 Verify thattire pressure is at specification See page 104 Verify that rear suspension ride height preload is at specification See page 88 Position the motorcycle on a level surface with the headlight 25 feet 7 6 m from a wall With the operator and passenger if applicable on board bring the motorcycle to the fully upright position Start the engine and switch the headlamp to high beam Observe the headlight aim on the wall Make any necessary adjustments to headlight aim See page 108 25 ft 7 6 m 7 5 in 19 cm Headlamp bulb center height Maintenance 107 Maintenance Headlight Aim Adjustment The headlamp adjustment screws are located inside the headlamp housing Adjustment Screws 1 CHIEFTAIN only Remove the two headlight bezel screws and remove the bezel from the fairing Reinstall the bezel after a
70. ading sit on the motorcycle and bring it to the upright position 65 Pre Ride Inspections Sidestand 1 2 66 On level ground straddle tne motorcycle and bring itto the fully upright position Move the sidestand up to the stored position and down to the fully extended position several times It should move smoothly and quietly Make sure the return spring holds the sidestand tightly in place when the sidestand is in the stored position Adjust or replace a loose spring Inspect the sidestand pivot bolt for looseness or wear Tighten or replace a loose or worn bolt Periodically test the sidestand safety switch for proper operation With the transmission in gear and brakes applied attempt to start the engine while the sidestand is down The engine should NEVER start in any gear except neutral if the sidestand is down If the engine starts during this test see your dealer for service Fasteners l Inspectthe entire motorcycle chassis and engine for loose damaged or missing fasteners 2 Tighten loose fasteners to the proper torque See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer 3 Always replace stripped damaged or broken fasteners before riding Use genuine INDIAN MOTORCYCLE fasteners of equal size and strength The operation section of this manual describes how to ensure maximum performance and longevity through the proper care and operation of your motorcycle Important a
71. age to the electrical system See page 114 Use only genuine INDIAN MOTORYCLE accessories designed for your model Do not exceed the gross vehicle weight rating GVWR for your motorcycle Adjustride height as needed See pages 89 91 11 Modifications Modifying the motorcycle by removing any equipment or by adding equipment not approved by the manufacturer may void your warranty Such modifications could make the motorcycle unsafe to ride and could result in severe injury to operator or passenger as well as damage to the motorcycle Some modifications may not be legal in your area of operation If in doubt contact your authorized INDIAN MOTORCYCLE dealer Parking the Motorcycle When leaving the motorcycle unattended turn the engine off Park the motorcycle where people are not likely to touch the hot engine or exhaust system or place combustible materials near these hot areas Do not park near a flammable source such as a kerosene heater or an open flame where hot components could ignite combustible materials Park the motorcycle on a firm level surface Sloped or soft surfaces may not support the motorcycle If you must park on a slope or soft surface follow the precautions outlined on page 78 12 Saddlebags Whenever operating a motorcycle with saddlebags or cargo Never ride at excessive speeds Saddlebags and cargo combined with the lifting or buffeting effects of wind can make the motorcycle unstable and
72. all applicable U S EPA Federal noise standards This warranty extends to the first person who buys this exhaust system for purposes other than resale and to all subsequent buyers Warranty claims should be directed to Anauthorized INDIAN MOTORCYCLE dealer or INDIAN MOTORCYCLE COMPANY P O Box 47700 Hamel MN 55340 9960 135 Warranty Emissions Control System Warranty INDIAN MOTORCYCLE COM PANY Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and INDIAN MOTORCYCLE COMPANY hereinafter INDIAN MOTORCYCLE are pleased to explain the emission control system warranty on your 2014 or later INDIAN motorcycle In California new motor vehicles must be designed built and equipped to meet the state s stringent anti smog standards INDIAN MOTORCYCLE must warrant the emission control system on your motorcycle for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your motorcycle Your emission control system may include parts such as the fuel injection system the ignition system catalytic converter and engine computer Also included may be hoses belts connectors and other emission related assemblies Where a warrantable condition exists INDIAN MOTORCYCLE will repair your motorcycle at no costto you including diagnosis parts and labor Manufacturer s Warranty Coverage Class IlI motorcycles 280cc and larger for a period of us
73. andlebar and hold it The lever should move freely and smoothly The lever should feel firm and continue to feel firm until released 2 Release the lever It should return to its rest position quickly when released 3 Ifthe front brake lever fails to perform as stated service the brake lever before riding Rear Brake Pedal 1 Press downward on the rear brake pedal It should move freely and smoothly The pedal should feel firm and continue to feel firm until released 2 Release the pedal It should return to its rest position quickly when released 3 Ifthe rear brake pedal fails to perform as stated or travels too far before beginning to engage the brake service the brakes before riding Rear Brake Fluid Level The rear brake fluid reservoir is located near the rear brake pedal View the reservoir level from the right side of the vehicle 1 Position the motorcycle on level ground in the fully upright position 2 View the brake fluid through the reservoir 3 The fluid should be clear Replace cloudy or contaminated fluid 4 The fluid level should be above the minimum indicator mark on the reservoir body Add brake fluid as needed See page 98 Minimum Level Mark Pre Ride Inspections Brake Lines Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid Tighten any leaking connections to the proper torque values and replace
74. ated Inspectfluid level fluid condition See pages 62 63 Anti Lock Brake Light Remains Illuminated or Illuminates I ntermittently Possible Cause Possible Remedy Action Blown fuse Check the fuses See page 113 Loose or damaged pulse ring Inspect pulse ring for looseness or chipped teeth Debris lodged in components Inspect wheel speed sensor and pulse ring for debris Damage caused by debris Inspect wheel speed sensor for cracked housing Damaged components See service manual or authorized dealer 119 Cleaning and Storage Cleaning Products This section provides tips on the very best way to clean polish and preserve every surface of your beautiful new INDIAN motorcycle We recommend the use of our new INDIAN MOTORCYCLE cleaning and polishing products and accessories which have been specially designed to offer the best care possible for your INDIAN motorcycle In addition to the products recommended in this section for cleaning and polishing INDIAN MOTORCYCLE also has specialty polishing products for removing scratches scuffs and swirls enhancing black and silver engines cleaning engines tires and wheels removing brake dust After cleaning the motorcycle inspect for damage to the painted surfaces Repair chips or scratches promptly by applying INDIAN MOTORCYCLE touch up paintto prevent corrosion For more information or for answers to your cleaning and detailing questions please s
75. based cleaners on the windshield as these products can damage the windshield Leather Care Leather must be cleaned and treated to properly maintain its quality appearance and extended life Clean and treat leather more often under adverse conditions Use only cleaners and conditioners specifically designed for leather use Use INDIAN MOTORYCLE Leather Care products Do notclean leather with household soap or cleaners Use high quality saddle soap or leather cleaner Use of some leather treatment oils will darken distressed leather Try a small amount on a hidden area first If you will not operate the motorcycle for more than 60 days store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration During storage preparation you might use products that are potentially hazardous such as fuel stabilizer When using any of these products follow the instructions and warnings on the product packaging Cleaning and Storage Storage Area Preparation Choose a dry well ventilated storage location inside a garage or other structure if possible The location should have a firm flat surface and allow enough space for the motorcycle WARNING Gasoline is highly flammable and explosive under certain conditions Do not store the motorcycle in any area in home or garage where it could be near open flames pilotlights sparks or electric motors Do not smoke in the
76. brake lever activates the front brake calipers The rear brake pedal activates the rear brake caliper For maximum brake effectiveness apply the front brake lever and the rear brake pedal together Front Brake Lever The front brake lever is located on the right handlebar This lever controls only the front brakes The front brakes should be applied simultaneously with the rear brakes To apply the front brake pull the lever toward the handlebar See page 75 for braking procedures Front brake lever reach distance to the hand grip is adjustable 1 Gently push and hold the lever away from the hand grip The adjuster wheel is located between the lever and the switch cube 2 To increase reach distance rotate the adjuster to align a lower number of hash marks with the pin 3 To decrease the reach distance rotate the adjuster to align a higher number of hash marks with the pin 4 Make sure the pin is fully seated into the selected hole Instruments Features and Controls Rear Brake Pedal The rear brake pedal is located Rear Brake on the right side of the Pedal motorcycle Press downward on the rear brake pedal to apply the rear brake WARNING Resting your foot on the brake pedal will cause excessive and premature wear of brake pads and reduced braking efficiency which could result in severe injury or death See page 75 for braking procedures 55 Instruments Features and Controls Fuel Cap The fue
77. cause loss of control Distribute weight evenly on each side of the motorcycle Do not exceed the individual weight limit of each saddlebag NEVEREXCEED GROSS VEHICLE WEIGHT RATING GVWR or the GROSS AXLE WEIGHT RATING GAWR regardless of whether or notthe saddlebags are loaded to capacity Exceeding the weight rating can reduce stability and handling and cause loss of control Adjustride height as needed See pages 89 91 Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle Where applicable these guidelines also refer to the contents of any accessories Keep cargo and accessory weight to a minimum and keep items as close to the motorcycle as possible to minimize a change in the motorcycle s center of gravity Changing the center of gravity can cause loss of stability and handling and could cause loss of control Adjust ride height as needed See pages 89 91 Do not exceed the gross vehicle weight rating GVWR for your motorcycle Distribute weight evenly on both sides of the motorcycle Maintain even weight distribution by checking accessories and cargo to make sure they re securely attached to the motorcycle before riding and whenever you take a break from riding Uneven weight distribution or sudden shifting of accessories or cargo while you re riding may cause difficult handling loss of control and driving hazards for other motorists if cargo falls from the motorcy
78. cle For riding comfort and to ensure proper ground clearance adjust rear shock air pressure as specified on the label located under the left side cover See page 90 Safety Do not attach large or heavy cargo such as sleeping bags duffel bags or tents to the handlebars front fork area or front fender Cargo or accessories placed in these areas can cause instability due to improper weight distribution or aerodynamic changes and could cause loss of control Such items can also block air flow to the engine and cause overheating that can damage the engine Do not exceed the maximum cargo weight limit of any accessory see accessory instructions and labels Do not attach cargo to an accessory not designed for that purpose Either circumstance could result in an accessory failure that could cause loss of control Always obey posted speed limits Do not attach anything to the motorcycle unless specifically designed for that purpose by INDIAN MOTORYCLE 13 Transporting the Motorcycle If you must transport the motorcycle Use atruck or trailer Do not tow the motorcycle with another vehicle as towing will impair the motorcycle s steering and handling Position and restrain the motorcycle in an upright position If the motorcycle leans to one side gasoline may leak from the fuel tank and result in a fire hazard or damage to the finish Do notrestrain the motorcycle using the handlebars e Loop tiedown straps from
79. cold weather This will allow oil to reach all areas before the engine is put under load NOTICE Do notrun the engine at high RPM with the clutch disengaged or the transmission in neutral Maximum safe engine speed is 5400 RPM Never exceed the maximum safe RPM as this could resultin serious engine damage NOTICE The engine is air cooled and requires unrestricted air flow to ensure proper operating temperature Long periods of idling or traveling at very low speeds such as during a parade may overheat the engine resulting in serious engine damage Operation 71 Operation Shifting Gears WARNING forced shifting with clutch engaged could cause damage to the engine transmission and drive train Such damage could cause loss of control which could result in serious injury or death Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears This motorcycle is equipped with a six speed transmission Neutral is located between first and second gear Press downward on the toe lever to shift to a lower gear Lift upward on the toe lever to shift to a higher gear Release the clutch lever after each gear shift 72 Shifting to neutral is easiest if the motorcycle is rolling slowly To shift from first gear to neutral gently lift the toe lever a half stroke Tip The transmission is in neutral if you can move the motorcycle forward or rearward freely without disengaging the cl
80. components as necessary See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer WARNING Brake fluid leaks or low brake fluid levels could cause brake systemfailure which could resultin serious injury or death Do not operate the vehicle with low brake fluid levels or when leaks are evident dampness or stains from dried fluid See your authorized INDIAN MOTORCYCLE dealer 63 Pre Ride Inspections Throttle Rotate the throttle control grip It should rotate smoothly from the rest position to the completely open position It should return to the rest position quickly when released Mechanical Clutch 1 Squeeze the clutch lever toward the handlebar and release it It should move freely and smoothly and it should return to the rest position quickly when released If the lever fails to perform as stated service the clutch lever before riding my O mif CC EIC P MR 2 Freeplay gap is the amount of lever movement from the rest position to the point of cable resistance Clutch lever freeplay should be 0 5 1 5 mm Measure the gap between the clutch lever and the lever housing See page 95 Adjust clutch lever freeplay if necessary Tip The starter interlock switch is dependent on the clutch lever freeplay being set correctly to ensure activation of the clutch safety switch Front Suspension Inspect the front forks for oil leaks or damage and verify smooth suspension operation See
81. cs Key Pad Diagnostics Key pad diagnostics allows the user to the test the function of each button on the left hand audio control block 1 Press and release each of the audio Q D control buttons to test the function of each button VA Observe the display after each button is pressed The 7 30 75F screen will display the button name by its function If VOL UP nothing displays the button is not working See your authorized dealer for service Press and release MODE to move to Tuner Location Settings Audio System Tuner Location Settings The radio tuner can be set to the geographical location where the 7 30 TSF motorcycle will be driven TUNER The following settings can be LOCATION chosen under the Tuner Location NORTH AMERICA Settings menu NORTH AMERICA USA CANADA MEXICO EUROPE EUROPE 50 e JAPAN AUSTRALIA TAIWAN c Press and release lt or c to make a new selection N Turn the power switch OFF then ON to save the new tuner location 169 Audio System Audio System Diagnostics Speed Diagnostic The Speed Diagnostic menu displays vehicle speed 7 30 75F Use this menu to verify the radio SPEED system is receiving a speed signal 0 MPH from the vehicle control module 0 KPH 1 Press and release MODE to return to the radio hardware version display screen 2 To exitthe audio system diagnostics menu press and release
82. ction D Material T Nl I Ay NS Minimum 1 0 mm Avoid using brakes harshly unless in an emergency Brake efficiency will gradually increase during this seating period When checking brake pad friction material thickness check each brake caliper for dampness or stains from leaking or dried brake fluid If inspection reveals signs of fluid leakage do not operate the vehicle See your dealer for service Brake Pads Front Brake Pad Inspection 1 Remove the two acorn nuts and one screw securing the protective caliper covers Remove the covers 2 Use an inspection mirror positioned atthe frontside of the caliper to view the friction material 3 Reinstall the caliper covers Torque 18ftlbs 24 Nm Front Caliper Cover Nuts Rear Brake Pad Inspection 1 Position the motorcycle on the sidestand with the handlebars turned to the left 2 Use an inspection mirror positioned at the front side of the caliper to view the friction material Maintenance Anti Lock Brake System ABS Tone Ring Sensor I nspection Visually inspect for aT damaged teeth onthe front and rear ABS tone rings Inspect for nicks and dents on the face of the teeth The teeth edges should be consistent in appearance If a tone ring is damaged see your dealer for replacement as soon as possible Inspect for debris Tone Ring Wheel Speed adhering
83. d Any part or parts replaced under this warranty shall become the property of INDIAN MOTORCYCLE In the State of California only emission related warranted parts are specifically defined by the state s Emission Warranty Parts List These warranted parts are carburetor and internal parts intake manifold fuel tank fuel injection system spark advance mechanism crankcase breather air cutoff valves fuel tank cap for evaporative emission controlled vehicles oil filler cap pressure control valve fuel vapor separator canister igniters breaker governors ignition coils ignition wires ignition points condensers and spark plugs if failure occurs prior to the first scheduled replacement and hoses clamps fittings and tubing used directly in these parts Since emission related parts may vary from model to model certain models may not contain all of these parts and certain models may contain functionally equivalent parts In the State of California only Emission Control System emergency repairs as provided for in the California Administrative Code may be performed by other than an authorized INDIAN MOTORCYCLE dealer An emergency situation occurs when an authorized INDIAN MOTORCYCLE dealer is not reasonably available a part is not available within 30 days or a repair is not complete within 30 days Any replacement part can be used in an emergency repair INDIAN MOTORCYCLE will reimburse the owner for expenses including diagnosis not to exceed INDI
84. d be connected to the black port The purge line should be connected to the gray or natural colored port 1 jy Evaporative 4 Emissions Canister California Models Fuel System Components 1 Inspectfuel hoses for cracks or damage Fuel Line Quick Disconnect 2 Inspect hose connections at the fuel tank and atthe fuel rail for dampness or stains from leaks The tank connection for the fuel line is under the tank console The fuel system is under pressure and caution must be used when inspecting and servicing the fuel system See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer w Throttle Control Inspection 1 With the engine OFF rotate the throttle control grip fully open and then release it It should rotate smoothly from the rest position to the completely open position It should return to the rest position quickly when released 2 Repeatthe twist and release process with the handlebars turned fully right and fully left 3 Service the throttle system if throttle operation is not smooth or if throttle grip does not return properly See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Sidestand Lubrication Periodically lubricate the sidestand bushing See page 66 for sidestand inspections Maintenance Mechanical Clutch Lever Freeplay 1 Hold the clutch cable The clutch cable adjuster nut is located along
85. djusting shock air pressure See page 88 Follow these guidelines when adjusting Park the motorcycle with the sidestand down on a firm level surface Remove all riders and cargo DO NOT exceed 150 PSI 1034 kPa in the shock Use the INDIAN MOTORYCLE Air Pump and Gauge P N PV 48909 Follow the instructions on the following pages If the recommended air pump is not available use a gauge and a pressurized air source with a maximum line and gauge pressure of 150 PSI 1034 kPa After using the alternate gauge remove it quickly to minimize leakage Expect to lose up to 5 PSI 24 kPa with each pressure check Use only a dry air source such as a system with a water separator or air line dryer to prevent moisture from entering the shock CAUTION Air pressure increases VERY quickly when using pressurized air Wear eye and face protection 90 Total Cargo amp Air Pressure MAX PRESSURE Occupant Weight psi 150 PSI Ibs 0 0 150 0 2 SELECT PRESSURE 175 0 CORRESPONDING 200 0 TO TOTAL CARGO 225 10 AND OCCUPANT WEIGHT REMOVE 250 23 ALL PASSENGERS 275 30 AND CARGO 300 3 BEFORE SETTING 2 CHECKING SHOCK 325 48 PRESSURE SET 350 60 PRESSURE WITH 375 71 BIKE ON SIDE STAND 400 85 425 100 450 122 475 134 500 145 7179871 Shock Air Pressure Ride Height Adjustment CHI EFTAI N 1 Park the motorcycle with the sidestand down on a firm
86. djusting the headlamp Tool M4 hex wrench or universal tool 2 To adjust the headlamp vertically tighten both top adjustment screws equally to adjust the beam downward Loosen both screws equally to adjust the beam upward Tool M4 hex wrench or universal tool 3 To adjust the headlamp horizontally loosen the left side screw to adjust the beam to the left Loosen the right side screw to adjust the beamto the right Headlight Lamp Replacement CHI EF 1 Remove the six bolts securing the front nacelle headlight shroud Pull this piece forward to access the headlight 2 Remove the sealing boot Press the looped end of the wire bulb retainer clip and swing the end toward the center of the bulb to release it from the latch tab 3 With the wire connector attached pull the bulb out Disconnect the wire harness 4 Install the new bulb and secure the retainer Tip Avoid touching a halogen lamp with bare fingers Oil from your skin leaves a residue causing a hot spot that will shorten the life of the lamp If a lamp is touched clean it thoroughly with denatured alcohol 5 Reinstall the sealing boot Make sure it seals tightly around the bulb base and lens to prevent condensation 6 Reinstall the front nacelle headlight shroud 7 Tighten the two 2 top bolts Torque 36in lbs 4 Nm 8 Tighten the four 4 rear bolts Torque 84in Ibs 9 5 Nm 108 Maintenance Headlight Lamp Replacement CHI EFTAI N 1 Remove the two bo
87. ducts is not covered by warranty Perform maintenance at the intervals specified in the periodic maintenance table beginning on page 82 Vehicles subjected to severe use must be inspected and serviced more frequently Severe Use Definition high speed operation for extended periods low speed operation for extended periods operation in dusty or otherwise adverse conditions operation in cold weather temperatures below freezing Maintenance 81 Maintenance Periodic Maintenance Table L Lubricate w proper lubricant Replace at specified interval or annually Replace as specified or every 2 years Odometer Reading in Miles Kilometers BEEEB E E NR E g 7 mem Bs B GE BB S E T E See table key below Page A 2B 2 S Ei fi g E f N S Xe S o 6 O o 6 o 6 gt gag B 8 El 8 E EJ EJ EJ E g Rss 8 8 8 5 8 8 S 3 g Key Fob Battery Engine Compression 116 l l l l l l Engine Oil amp Filter 84 R R R R R R R R R R R g Crankcase Vent 93 l l l l l l l l l l l l gt Engine Mount Fasteners l w Oil Lines Oil System Inspection l l l l l l l l l l l l Air Filter 86 l l l R l l R l l R l Exhaust System 116 l l l l l l l l l l l l Spark Plugs 105 l l R l Battery Connections 110 l l l l l l l l l l l l
88. e This screen displays the average motorcycle speed and current battery voltage 1 Press and hold LEFT TOGGLE to reset the average speed 2 Press LEFT TOGGLE to cycle to Expanded Audio Information Expanded Audio Information In this mode the display screen will dedicate zone three to the audio system and allow for up to six lines of audio system information Press LEFT TOGGLE to cycle to Heated Grips if equipped Diagnostic Trouble Codes if present Trip 1 top of menu 7 30 75F FM 93 7 AVG SPEED 55 MPH 12 9 VOLTS RANGE 250 25680 mi 6 7 30 75F iPOD ARTIST SONG TITLE ALBUM TITLE RANGE 250 25680 mi 6 Instruments Features and Controls Heated Grips if equipped If heated grips are installed on the motorcycle the Heated Grips display will show the current heated grip power level setting Tip This screen will not appear if heated grips are not installed or if the power level is setto zero Press LEFT TOGGLE to cycle to Diagnostic Trouble Codes or the top of the menu 7 30 75F FM 93 7 HEATED GRIPS a Power Level 9 mec 250 25680 mi 6 39 Instruments Features and Controls Instrument CHIEFTAI N Zone Three I nformation Diagnostic Trouble Codes DTCs Ifthe CHECK ENGINE indicator is illuminated on the instrument cluster this screen will display indicating there are Diagnostic Trouble Codes DTCs The
89. e desired tuner band Press and release MODE to move to the next selection 7 30 SOURCE OFF SOURCE ON 75F DRIVE DEVICE F330 NAV AUDIO OFF 15F 7 30 FM CLEAR PRESETS 75F 7 30 FM PRESETS CLEARED 75F Audio System Radio Broadcast Data System RBDS 1 Press qj or c to turn the 7 30 75F Radio Broadcast Data System RBDS RBDS When on the screen FULL will display artist song title etc if available in the radio ON signal OFF ON Station name only FULL Station name radio text Press and release MODE to move to the top of the MODE menu list N eo o 167 Audio System Audio System Diagnostics The audio system diagnostic menu allows the following actions for you or your INDIAN MOTORCYCLE dealer View radio software version e Perform left hand audio control key pad tests Setradio tuner location View vehicle speed Diagnostic Menu To access the diagnostic menu Turn the power switch OFF Turn the power switch ON UBWN BP This screen will appear if steps 1 3 were performed correctly Tip If you do not see this screen perform steps 1 3 again 6 Press and release MODE to move to Key Pad Diagnostics 168 Press and hold c to turn the radio off Press and hold PRE for several seconds 7 30 RADIO SW 1 00A HW1 BOOT V 1 00A 75F Audio System Diagnosti
90. e of five 5 years or 30 000 kilometers 18 641 miles whichever first occurs If an emission related part on your motorcycle is defective the part will be repaired or replaced by INDIAN MOTORCYCLE This is your emission control system DEFECTS WARRANTY 136 Warranty Emission Control System Warranty Owner s Warranty Responsibilities Asthe motorcycle owner you are responsible for the performance of the required maintenance listed in your Rider s manual INDIAN MOTORCYCLE recommends that you retain all receipts covering maintenance on your motorcycle but INDIAN MOTORCYCLE cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance You are responsible for presenting your motorcycle to an INDIAN MOTORCYCLE dealer as soon as a problem exists The warranty repairs should be completed in a reasonable amount of time notto exceed 30 days As the motorcycle owner you should be aware that INDIAN MOTORCYCLE may deny your warranty coverage if your motorcycle or part has failed due to abuse neglect improper maintenance or unapproved modifications If you have any questions regarding your warranty rights and responsibilities you should contact INDIAN MOTORCYCLE COMPANY P O Box 47700 Hamel Minnesota 55340 9960 or the California Air Resources Board P O Box 8001 9528 Telstar Avenue El Monte CA 91734 8001 INDIAN MOTORCYCLE COMPANY hereinafter INDIAN MOTORCYCLE warrants that
91. e sure the mounting bracket is seated fully on the spool Make sure the rubber bushings on the latch pins are fully engaged in the spools 5 Engage the quick release latches and flip them fully downward Mounting Bracket Latches Spool Saddlebags Hard Bag Removal 1 Unlock the electric saddlebag locks if equipped Tip The provided key can also be used in the latch release buttons to manually unlock the saddlebag lids 2 Remove the side cover Electrical Connection 3 Disconnect the saddlebag lock electrical wiring near the seat 4 Press the lid latch release button and lift the saddlebag lid 5 Flip the two quick release latches upward 6 Tiltthe saddlebag away from the frame of the vehicle to remove it Spool Bushing Latch Pin Quick Release Latch Instruments Features and Controls 7 Toreinstall place the hard bag ina fully seated position on the muffler NOTICE To prevent damage to components always make sure saddlebags are fully seated onto the muffler before engaging the latches 8 Make sure the rubber bushings on the latch pins are fully engaged in the spools Engage the quick release latches and flip them fully downward 9 Reconnect the electrical wiring 10 Reinstall the side cover using care to avoid damaging electrical wires 51 Instruments Features and Controls Windshield Windshield Removal CHIEF if es 1 Ifequipped witha quick latch wi
92. ee your INDIAN MOTORCYCLE dealer 120 Washing the Motorcycle NOTICE Do notuse pressurized water to wash the motorcycle Water may seep in and deteriorate wheel bearings brake caliper assemblies brake master cylinders electrical connectors steering head bearings and transmission seals Do not direct any water stream at air intakes exhaust outlets or electrical connectors Electrical components may be damaged by water Do not allow water to contact electrical components or connectors 1 Before washing make sure exhaust pipes are cool Cover each pipe opening with a plastic bag secured with a strong rubber band Check that the spark plugs spark plug wire caps oil fill cap and fuel caps are properly seated 2 Donotuse abrasive cleaners 3 Rinse off as much dirt and mud as possible with water running at low pressure Use as little water as possible when washing near the air intake or the exhaust pipe openings Dry these components thoroughly before using the motorcycle 4 Cleanthe frontfork tubes thoroughly to reduce fork seal wear and leakage 5 After washing remove the rubber bands and plastic bags from the exhaust pipes Start the engine and let it idle for a few minutes 6 Make sure the brakes are functioning properly before riding Windshield Care Rinse the windshield with clean water to remove loose dirt and dust NOTICE Do not use glass cleaners water or soil repellents and petroleum or alcohol
93. election 153 Audio System Selecting Audio Sources USB Audio Source Pandora Internet Radio Pandora internet radio is available only when the user 3 To give a THUMBS UP for connects a compatible iPhone or iPod device to the radio the current song press and 7 30 TSF using the USB connector hold gt gt THUMBS UP Pandora internet radio is intended ARTIST for use only in the United States 7 30 75F SONG TITLE Australia and New Zealand If PANDORA f licensing restrictions prevent NOT 4 Togive a THUMBS DOWN 7 30 75F Pandora from playing NOT for the current song Press El c ONES i 220 AVAILABLE displays AVAILABLE and hold lt THUMBS DOWN 1 Turn on the Pandora app ARTIST Connect a compatible iPhone 7 30 75F SONG TITLE or iPod device to the USB PANDORA re When a commercial is playing i bud lease mope unii ARTIST the screen will display the 7 30 75F Press and release MODE un following information ANDORA Pandora is displayed in the SOE TLE PANDORA screen Tip If Pandora is the currently playing app on the device the USB source displays information and enables features specific to the app If itis not you must select Pandora from the category menu Press and hold PRE 154 Selecting Audio Sources Audio System USB Audio Source Pandora Internet Radio 5 To skip forward to song press and re 6 Whenthe skip lim the next lease
94. elt dust can collect 3 Rinse the belt with clear water then dry thoroughly Tip Do not inspect or adjust drive belt tension when the belt or drive system is wet or hot Improper adjustment will result Rear Drive Belt Condition Inspect the rear drive belt at the intervals specified in the periodic maintenance table beginning on page 82 Replace the drive belt if itis cracked or has broken teeth or frayed edges No matter its condition the drive belt should be replaced at periodic intervals See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the vehicle has been run at operating temperature within the last four hours Allow the vehicle to cool down to ambient temperature before measuring belt tension Replace the drive belt and both sprockets as a set if the drive belt has over 5 000 miles 8 000 km of service atthe time of damage or failure Rear Drive Belt Wear Analysis pesa ole Internal tooth cracks External tooth cracks Missing teeth Chipping not serious hairline Replace belt Replace belt OKto run but monitor OKto run but condition monitor condition ET oaooooooog ZZ A rc Fuzzy edge cord Hook wear Stone damage Bevel wear OKto run Replace belt Replace belt if damage is outboard edge only but monitor condition on edge
95. engine See page 69 1 Perform the Pre Ride Inspections See page 57 Properly secure any cargo 2 Straddle the motorcycle and bring itto the fully upright position Retract the sidestand Tip When the electrical system is activated with either the power switch or the starter switch the key fob must be within range See page 26 i er 3 Move the engine stop run switch to the RUN position 8 If either the check engine indicator or the low oil mes pressure indicator or display remains on after the Shift the transmission to neutral engine starts stop the engine immediately Refer to the 5 Apply the front brakes Disengage the clutch pull the low oil pressure indicator display information on page clutch lever fully toward the handlebar 32 or 34 NOTICE Operating an engine with a misfire or non firing cylinder can overheat the catalytic converter which could result in catalytic converter damage and loss of emission control DO NOT OPERATE the motorcycle if a misfire or non firing cylinder exists continued on next page A 70 Starting the Engine 9 Leave the throttle closed and allow the engine to idle Idle speed will gradually slow to normal as the engine warms to operating temperature Tip Do not rev the engine or put the transmission in gear immediately after starting the engine Allow the engine to idle for about 30 seconds after a warm start or at least one minute after a cold start longer in
96. ently We recommended checking the oil each time you refuel The engine must be at normal operating temperature when checking the oil level NOTICE Oil level will NOT be accurate if checked on a cold engine DO NOT ADD oil to bring level to the FULL mark on a cold engine asthis can result in overfilling The oil fill cap dipstick is located on the left side of the motorcycle A special tool is provided in the tool kit to assist with dipstick removal Always use the recommended oil See page 128 Oil Fill Cap Dipstick 1 qt 946 cc Low 60 1 Start the engine and allow it to run until it reaches normal operating temperature 2 Stop the engine and wait one minute before checking the oil level Tip If the oil level is not checked within 3 minutes repeat steps 1 2 3 Position the motorcycle on level ground in the fully upright and centered position Remove the dipstick and wipe it clean Reinstall the dipstick until fully seated Remove the dipstick and view the oil level Add the recommended oil as needed to bring the level within the safe operating range anywhere between the two marks on the dipstick with engine at operating temperature If the oil level on the dipstick is anywhere in the safe range do not add oil Oil should be added only ifthe proper oil check procedure is followed AND the level is below the safe mark 8 Do notoverfill Overfilling can resultin loss of engine performance and an oil sa
97. enu will display C nextto each position BT SETUP when there is either a headset or C DRIVE H SET device connected C B Vp Oz e Each Bluetooth position can have a EXIT maximum of three devices paired to that location To add another device you must remove one or all of the paired devices e Only one device can be connected at any given time During audio system power up the radio will search through the list of paired devices and make connections to one of each pair ing position Tip Turning the source off in the MODE MENU will not prevent the device from connecting it only prevents it from appearing on the audio source loop This allows a device to be paired and connected only for the purpose of receiving phone calls e Left hand audio controls are limited to basic functions when devices are connected via Bluetooth To maintain full left hand audio controls connectthe device to the USB cable Audio System 163 Audio System Audio M ode M enus Bluetooth Setup M enu Driver Headset Pairing Incoming phone calls cannot be answered if driver headset is not connected Press and release PRE or MODE to send the calls to voice mail 1 Press and hold MODE to access the audio menu 2 Press and release MODE until BLUETOOTH SETUP is displayed 3 Press and release PRE to access the Bluetooth Setup Menu options 4 Inthe Bluetooth Setup Menu press c or c to make a selection Select DRIVE
98. er left side cover 114 Unlocking the Security System If a key fob is not available your personal identification number PIN can be entered using the turn signal switches to unlock the security system Use the following guide to enter your valid PIN Peg Turn Signal Digitto Enter Feature Used Procedure The number 0 CANCEL switch Press and release First digit 1 9 LEFT turn switch Second digit 1 9 RIGHT turn switch Third digit 1 9 LEFT turn switch Fourth digit 1 9 RIGHT turn switch Move and release once per digit value See example below Example for entering the number 1024 LEFT CANCEL LEFT LEFT RIGHT RIGHT RIGHT RIGHT Changing Your Security System PIN To change your PIN you must have either the key fob or your existing valid PIN available to gain access to the security system If the key fob is not detected or is not available and you cannot remember your PIN please see your INDIAN MOTORCYCLE dealer Please read the entire procedure before beginning 1 Turn the power switch on Do NOT start the engine The security light and or power switch will turn on briefly until the key fob is detected or the valid PIN is entered 2 Whenthe key fob is detected the security light and or power switch will turn off Proceed to step 4 If the key fob is not available or is not detected enter your valid PIN within 20 seconds See page 114 T
99. erfill Reinstall the diaphragm cover and screws Torque 13in Ibs 1 4 Nm Wipe away any fluid spills Check for signs of brake fluid leaks around hoses fittings reservoir and brake calipers Check for deterioration of hoses 99 Maintenance Brake Disc Inspection Cleaning 1 100 Inspect brake discs for nicks scratches cracks or other damage Inspect the thickness of each brake disc at four or more locations around the disc If any disc is worn to the minimum thickness at the thinnest point or if a disc is damaged see your dealer for replacement Clean discs if minor squeaks develop due to dirt or dust Apply brake cleaner to a clean shop towel and wipe the discs DO NOT allow brake cleaner to contact painted or plastic parts Read all precautions on the label E i a Minimum Thickness Front 4 5 mm Rear 6 5 mm Brake Pads Inspect each front brake pad on both sides of the front disc Inspect each rear brake pad on both sides of the rear disc Replace brake pads when the thinnest point of the friction material has worn to 1 0 mm Please see your dealer for this service Tip After replacing pads allow up to 250 miles 500 km of operation in urban driving conditions not highway cruising to allow pads to mate with new rotors Brakes should be used frequently During this time brake performance will be less effective Fri
100. ess the MFD Use the mode switches to toggle through the modes of the multi function display and to change settings in the display Modes Available Odometer Engine Speed Trip Odometer 1 Average Fuel Economy Trip Odometer 2 DC Voltage Clock Ambient Air Temperature Gear Indicator Fuel Range Odometer The odometer displays total distance traveled Instruments Features and Controls Trip Odometers The trip odometers Trip 1 and Trip 2 display total distance traveled since being reset To reset a trip odometer toggle to the trip odometer then press and hold the LEFT TOGGLE switch until the trip odometer resets to zero Engine Speed Engine speed displays in revolutions per minute RPM DC Voltage The volt meter displays battery voltage If the engine is not running approximate battery voltage displays If the engine is running approximate charging voltage displays Gear Position Gear position displays at all times while the engine is running unless a fault occurs with the gear position sensor Temperature The temperature area displays ambient air temperature Fuel Range The fuel range displays the distance the motorcycle can travel on the remaining fuel in the fuel tank Average Fuel Economy Average Fuel Economy displays as of the last time the mode was reset To reset press and hold LEFT TOGGLE while viewing the fuel economy display 29 Instruments Features and
101. fastened Low Compression Please see your dealer for an engine compression test Starter Motor Clicks Does Not Turn or Turns Slowly Possible Cause Possible Remedy Action Engine Stop Run Switch in Stop Position Place switch in RUN position Battery Discharged Fully charge the battery See page 112 Battery Cables Loose or Corroded Inspect battery cables Transmission In Gear Shift transmission into neutral or pull the clutch lever in to disengage the clutch See starting procedures on page 70 Key Fob Not Authenticated Make sure key fob is within range and that key fob battery voltage is not low Sidestand is Down With Transmission in Gear Shiftto neutral or retract the sidestand fully 117 Maintenance Troubleshooti ng Engine Starts But Misses or Runs Poorly Tip Turn engine OFF before inspecting any of these items Possible Cause Possible Remedy Action Battery Discharged Fully charge the battery See page 112 Battery Cables Loose or Corroded Inspect battery cables and connections Spark Plug s Fouled Inspect spark plugs See page 105 Spark Plug Wire s Loose or Wet Inspect spark plug wires ensure dry secure Contaminated Fuel Inspect fuel for water contamination Please see your dealer Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil See page 60 Loose Broken S
102. fill NOTICE After an oil change the low oil pressure indicator may illuminate when the engine is started If this occurs do not increase RPM above idle speed until the indicator turns off Operating above idle speed could result in damage to the engine 1 Change the oil and filter when the engine is warm If the engine is cold start the engine and allow itto run atidle for atleast 5 minutes 2 Park the motorcycle with the sidestand down on a firm level surface If using a service lift the motorcycle should be centered 3 Clean the area around the two drain plugs Place a drain pan under both drain plugs CAUTION Hotoil can cause burns to skin Do not allow hot oil to contact skin 4 Remove the drain plugs Allow the oil to drain completely 5 Install new sealing washers on the drain plugs The sealing RBS surfaces on drain plugs and engine should be positis clean and free of burrs nicks or scratches 6 Reinstall the drain plugs Torque to 15 ft Ibs 20 Nm CAUTION Hotoil can cause burns to skin Do not allow hot oil to contact skin Wear leather gloves when handling hot components 7 Place shop towels beneath the oil filter Using an oil filter wrench turn the filter counter clockwise to remove it Engine Oil Filter Change 8 Using a clean dry cloth clean the filter sealing surface on the engine 9 Lubricate the o ring on the new filter with a film of fresh engine oil Check to make su
103. g speed of motorcycles equipped with these items Safe Riding Practices Follow these general safe riding practices Before each ride perform the pre ride inspections as outlined beginning on page 57 Failure to do so may result in damage to the motorcycle or an accident Until you re thoroughly familiar with the motorcycle and all of its controls practice riding where there is little or no traffic Practice riding at a moderate speed on various road surfaces and in different weather conditions Know your skills and limits and ride within them Allow only licensed experienced operators to ride your motorcycle and then only after they have become familiar with its controls and operation Make sure all riders read and understand this rider s manual before riding Do not ride when you re fatigued ill or under the influence of alcohol prescription drugs over the counter drugs or any other drugs Fatigue illness alcohol and drugs can cause drowsiness loss of coordination and loss of balance They can also affect your awareness and judgment If your motorcycle operates abnormally correct the problem immediately See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Safety Ride defensively as if you are invisible to other motorists even in broad daylight A motorists failure to see or recognize a motorcycle is the leading cause of automobile motorcycle accidents Ride where you re clearly v
104. ge ENGINE Oll Gscdredpi teet aree 84 Engine Oil Filter 85 Fluid Level Engine Oil eriad 60 FrontBrake cicisd cee ee mice inas 62 Front Brake Fl id 2 2 c ess 99 Rear Brake ee ee eee 63 Rear Brake Fluid 98 Fork Inspecton sese m 92 Front Wheel Installation 102 Fuel Capui mne efr is 56 USL Filter uitia enit 85 Fuel Gauge CHIEFTAIN 33 Fuel Handling Safety 14 UCI level netten ue prt bee 65 Fuel Recommendation 128 Fuel System Inspection 94 Fuel System Priming 69 Fuel cirea nn ettam eR Rt ei cx et OR Geek 69 Fuse Replacement 113 172 G Gasoline Handling Safety 14 Gear ShiftLever 005 49 Gear Shifting i ss eee seas 72 74 Gross Vehicle Weight Rating 16 GVW Racin git eset antes a i el a aus 16 H Hazard SWItGbi 1s re de 25 Headlight Aim Adjustment 108 Headlight AimInspection 107 Headlight Lamp Replacement CHIEF 108 Headlight Lamp Replacement CHIEFTAIN 109 High Low Headlight Beam Switch 27 l Identification Number Record 129 Ignition Key Fob isaueses eren aa 26 Ignition Keyless ocra nacer eener kina 26 Indicator Lamps CHIEF 28 Indicator Lamps CHIEFTAIN 34 35 Instrument Cluster CHIEF 28 32 Instrument Cluster CHIEFTAIN 33 47 L
105. he fuel pump to run until it stops about 2 seconds Move the engine stop run switch to the STOP position Repeat steps 3 5 four to five times Move the engine stop run switch to the RUN position Start the engine See page 70 AWN ouod 69 Operation Starting the Engine The starter interlock system allows the engine to be started 6 Press and hold the starter switch to engage the one only when the transmission is in neutral or when the touch starting feature which activates the electrical transmission is in gear with the clutch disengaged clutch system and starts the engine Another option is to turn lever pulled in The engine should NEVER start in any gear the power switch on and with the throttle closed press except neutral if the sidestand is down See page 50 and release the starter switch to start the engine The Tip Ifthe motorcycle runs out of fuel prime the starter motor will crank until the engine starts but no more than 3 seconds If the engine does not start wait five seconds then try again 7 fstarting a COOL engine DO NOT open the throttle while starting Idle speed is computer controlled and idle speed will adjust automatically depending on engine temperature and air temperature Allow the engine to warm up for 30 seconds minimum at low RPM after starting Do not run the engine above 2500 RPM If starting a WARM engine DO NOT open the throttle while starting system before attempting to restartthe
106. he handlebars to the left for maximum stability Lean the motorcycle to the left until the sidestand firmly supports the motorcycle CAUTION Ifthe motorcycle weight is not resting on the sidestand it will not lock In this situation any movement of the motorcycle could cause the sidestand to retract slightly If the sidestand is not in the full forward position when the motorcycle weight is rested on it the motorcycle could fall over possibly causing injury and damage to the motorcycle To retract the sidestand straddle the motorcycle and bring itto the fully upright position Swing the end ofthe sidestand upward and toward the motorcycle until itis fully retracted 50 Saddlebags Do not exceed the weight limit of each saddlebag Always distribute weight evenly in each of the saddlebags Hard bag capacity is 22 pounds 10 kg of cargo per side Soft bag capacity is 15 pounds 6 8 kg of cargo per side Soft Bag Removal 1 Unbuckle the saddlebag lid clasps and open the lid 2 Flip the two quick release latches upward 3 Tiltthe saddlebag away fromthe fender and lift upward to remove it from the spools WARNING improper saddlebag installation can result in loss of control accident and driving hazards for other motorists if saddlebag falls from the motorcycle Always make sure saddlebag mounting brackets are fully seated onto the spools before engaging latches 4 Toreinstall place the soft bag in position Mak
107. he transmission in neutral slowly rotate the rear wheel If the wheel does not rotate smoothly see your dealer for service 91 Maintenance Front Fork Suspension Inspection 1 92 Place the motorcycle on the sidestand and inspect the front forks If fork oil is present on the outer tube do not ride the motorcycle See your dealer for service before operating If fork oil is present around the fork seals or inner tubes replace the fork seals Fork Inner Tube Fork Outer Tube 2 Clean the fork tubes to remove bugs tar or buildup which may cause seal wear or leakage Inspect the outer surfaces of the inner fork tubes for scratches or damage from foreign objects Straddle the motorcycle and bring itto the fully upright position Apply the front brake and push downward hard on the handlebars several times The front suspension should operate smoothly and quietly Fork oil condition and level affects front suspension performance and internal component wear Replace fork oil at the recommended intervals Special tools are required to perform this procedure See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Steering Head Inspection I Elevate and support the motorcycle with the front tire slightly off the floor See page 116 CAUTION Make sure the motorcycle is stable when elevated Injury may occur if the motorcycle tips or falls 2 Turn the handlebars from stop to st
108. hich can make the motorcycle hard to handle and cause loss of control Safe Riding Practices Protecti ve Apparel Wear protective apparel to decrease the risk of injury and increase riding comfort Always wear a helmet that meets or exceeds established safety standards Approved helmets in the USA and Canada bear a U S Department of Transportation DOT label Laws in some areas require that you wear an approved helmet Head injuries are the leading cause of fatalities in accidents involving motorcycles Statistics prove that an approved helmet is the most effective protection in preventing or reducing head injuries Wear eye protection to protect eyes from wind or airborne particles and objects Laws in some areas require that you wear eye protection We recommend that you wear approved Personal Protective Equipment PPE bearing markings such as VESC 8 V 8 Z87 1 or CE Make sure protective eyewear is kept clean 10 All riders should wear brightor light colored and or reflective clothing to improve visibility to other motorists A rnotorist s failure to see or recognize a motorcycle is the leading cause of automobile motorcycle accidents Wear gloves a jacket heavy boots and long pants to prevent or reduce injury from abrasions lacerations or burns should the motorcycle fall Wear boots with low heels as high heels can catch on pedals or footrests The combination of boots and pants should completely cover legs ankles a
109. horted Ignition Coil Wires Inspect coil primary wires Please see your dealer Air Intake Restricted Inspect air filter See page 86 Intake Leaks Inspect air box throttle body and intake boot joints Shif ng Difficulties or Hard to Find Neutral Possible Cause Possible Remedy Action Shift Linkage Bushings Dry Or Worn Lubricate shift linkage Clutch Damage Replace clutch Clutch Cable Not Adjusted Properly Please see your dealer for inspection and adjustment Shift Linkage Not Adjusted Properly Please see your dealer for inspection and adjustment 118 Maintenance Troubleshooti ng Battery Charging Rate Low or Battery Discharges Possible Cause Possible Remedy Action Loose Corroded Charging Circuit Connection Check clean battery cable connections Check clean charging circuit connections Please see your dealer Accessory Load Exceeds Charge Rate Limit accessory operation when the engine is off Improperly Wired Accessory Current Draw Please see your dealer to check charging system output and current draw Brake Noise Poor Brake Performance Tip See your dealer if brake performance does not return after these inspections Possible Cause Possible Remedy Action Dust Dirt On Brake Disc s Clean disc See page 100 Worn Pads Or Disc Brake Disc Damage Inspect pads See page 100 Brake Fluid Level Low Or Fluid Contamin
110. ht of the nozzle and hose on the filler neck Do notleave the nozzle unattended WARNING Overflows or spilled gasoline could contact a hot engine or exhaust system and cause a fire which could result in serious injury or death Do not allow gasoline to contact hot components WARNING Always remove the fuel cap slowly and fill the fuel tank slowly to prevent spillage Do not overfill the fuel tank Leave space in the tank to allow for the fuel to expand Ornamental Cap amp Do not remove 1 Turn the fuel cap counter clockwise to remove it 2 Insert the fuel nozzle into the fuel tank filler neck The nozzle stop at the bottom of the filler neck will prevent over insertion Operation 3 Add fuel to the tank until it touches the bottom edge of the filler neck The tank is full at this level 4 Always securely install the fuel cap before remounting the motorcycle To tighten the cap turn it clockwise until the seal compresses onto the tank then continue to tighten until the cap ratchets several times NOTICE Fuel can damage painted surfaces and plastic parts If gasoline spills on the any part of the motorcycle immediately rinse it off with water or wipe it dry witha Clean cloth Priming the Fuel System If the motorcycle runs out of fuel prime the fuel system before attempting to restart the engine 1 Fill the fuel tank Turn the power switch on Move the engine stop run switch to the RUN position Allow t
111. ical 96 Clutch Inspection Mechanical 64 Index C Clutchibever ei ironin eeka dx Nena 48 Clutch Lever Freeplay Mechanical 95 Clutch Lever Lubrication Mechanical 96 Compliance Vehicle 15 Console Components 21 Cruise Control Operation 76 77 Cruise Control Switches 25 D Diagnostic Functionality 31 Display Units Standard Metric 30 Drive Belt CE ARMING i aiae aai Weare thc si 86 COMOIM OD isses icd gad tert ROS 87 Wear Analysis elsu 87 Drive Belt Inspection Rear 65 E Electrical Precautions 114 Elevating the Motorcycle 116 Emission Control System 94 Engine Break In 00 67 68 Engine Compression Test 116 Engine Identification Number 20 Engine Oil Change 84 85 Engine Starter Switch 26 Engine Stop Run Switch 25 Engine Starting snet ea t 70 71 Engine Stopping 5 75 Equipment Modifications 12 Error Codes Engine CHIEF 31 Exhaust Safety 152 nece oe nhe has 14 Exhaust System Inspection 116 171 Index F Fastener Inspection 66 116 Fastener TOFGQUSS uua ears gare acs 116 Fluid Brake Fluid Specifications 128 Engine Oil Specifications 128 Fork Oil Specifications 128 Fluid Chan
112. ice NAV Audio AM FM Clear Preset Radio Broadcast Data System RBDS Audio System Introduction Audio Controls The audio controls are located on the left handlebar Wi U Radio On Off Volume Menu Scroll Tuner Music Track Select Menu Navigation Preset Button Select Enter Menus Mute Push to Talk PTT Voice Recognition Mode Button Audio System a vot 2 voLo D TUNE Q TUNE PRESET Tip Some mode menu options have sub menus Sources and menu options will be displayed only for installed components 145 Audio System Audio System Introduction Instrument Cluster Audio Display The audio system information is displayed in the center display on the instrument cluster All audio system information is displayed in zones two 2 and three 3 7 30 Z9F ZONE 2 FM 93 7 TRIP 1 MI 210 3 ZONE 3 HR 3 5 RANGE 250 25680 mi 6 146 USB Connector A USB connector cord is located on the right side of the lower front fairing A pouch is provided to hold your device while operating This pouch is padded and tethered to the fairing to securely hold your device Tip Device to USB adapters are not supplied with motorcycle and must be purchased separately Reference device owner s manual for USB accessory adapter inf
113. ight Switc va Power Switch E SER Power Switch Saddlebag Lock Switch 23 Instruments Features and Controls Switches Symbol Switch Description Emergency Flasher Switch Hazard Switch The hazard switch activates and cancels the emergency flashers See page 25 High Low Headlight Beam Switch The high low headlight beam switch toggles the headlight between high beam and low beam See page 27 Auxiliary Light Switch Press the auxiliary light switch to turn the auxiliary lights off or on See page 27 Horn Switch To sound the horn press the horn switch Turn Signal Switch Move the switch to the left to activate the left turn signals Move the switch to the right to activate the right turn signals A signal will deactivate automatically when speed or distance reach predetermined levels To cancel a signal manually move the switch to the center position and push it inward Momentary Feature Move the turn signal switch left or right and hold itin that position for at least one second The momentary feature will activate and the signal will then cancel when the switch is released Stop Run Switch Press the bottom of the switch RUN to allow the engine to start and run Press the top ofthe switch STOP to stop the engine See page 25 Starter Switch Use the starter switch to start the engine The engine stop run switch must be in the RUN positi
114. injury could result If not likely to contact hot components you do not have the time tools and expertise necessary to Wear eye and face protection when using pressurized air complete a procedure properly please see your dealer for service Never startthe engine or letitrun in an enclosed area Engine exhaust fumes are poisonous and can cause loss of consciousness Review the safety related maintenance information on page 15 or death in a short time Before beginning any maintenance procedure read the During some procedures you may use potentially hazardous instructions for the entire procedure products such as oil or brake fluid Always follow the instructions Always position the motorcycle on a firm level surface before and warnings on the product packaging performing service Make sure the motorcycle will not tip or fall while elevated or while on the sidestand See page 116 79 Maintenance Proper maintenance assures the highest level of safety durability and dependability for your motorcycle Break in maintenance is required to ensure warranty coverage and proper emissions system operation Performthe break in maintenance procedures when the motorcycle s odometer registers 500 miles 800 km Please see your authorized dealer for this service Performthe recommended periodic maintenance at the intervals specified in the periodic maintenance table beginning on page 82 Road Tests Before returning the mot
115. ion Inspect pedal and lever movement Brake Fluid Levels Check front and rear brake fluid levels Brake Components Inspect hoses and connections Throttle Inspect hand grip and throttle movement Clutch Check lever operation and freeplay Front Suspension Check for leaks debris and damage Steering Check for smooth operation by turning handlebars full left and full right Rear Suspension Check mounting and inspectfor leaks CHIEFTAIN Check shock movement and air pressure verify ground clearance Ride Height Make sure preload is adjusted properly for load See pages 88 91 Rear Drive Belt Check for wear or damage Check drive belttension See pages 86 87 Sidestand Verify smooth operation inspect pivot bolt and spring Fasteners Inspectfor loose damaged or missing fasteners Mirrors Adjustfor proper rear view 59 Pre Ride Inspections Engine Oil Level With the semi dry sump lubrication system the engine oil level on the dipstick will fluctuate depending on the motorcycle s position and engine speed when the engine is turned off To ensure a proper reading of the engine oil level follow all inspection procedures closely WARNING Operating with insufficient deteriorated or contaminated engine oil will cause accelerated wear and may result in engine or transmission seizure which could resultin loss of control and serious injury or death Check the oil level frequ
116. ip If the valid PIN is not entered within 20 seconds the security light and or power switch will flash for 10 seconds then the system will shut down Return to step 1 to try again 3 Whenthe PIN is accepted the security light and or power switch will turn off Proceed to step 4 4 Whenthe security light and or power switch turns off press and hold the turn signal CANCEL switch for 10 seconds The security light and or power switch will turn on to confirm access to the security system Proceed to step 5 to enter your new PIN Maintenance Entering Your New PIN 5 Enter your new 4 digit PIN 6 If4 digits are successfully entered the security light and or power switch will remain on and the horn will sound briefly Proceed to step 7 Tip If the 4 digit PIN is NOT successfully entered within 20 seconds the security light and or power switch will flash for 10 seconds then the system exits the procedure Return to step 1 to try again 7 Re enter the new 4 digit PIN If this entry matches the first entry the security light and or power switch will turn off and the horn will sound briefly Your new PIN has been saved Tip If the second entry is not entered within 20 seconds or does not match the first entry the security light and or power switch will flash for 10 seconds then the system exits the procedure The new PIN was NOT saved Continue to use your former valid PIN Return to step 1 to try again 115 Maintenance
117. isible to other motorists and observe their behavior carefully Be especially cautious at intersections as these are the most likely places for an accident To prevent loss of control keep your hands on the handlebars and your feet on the footrests Be aware that a highway bar is not designed to protect the rider from injury in a collision Obey the speed limit and adjust your speed and riding technique based on road weather and traffic conditions As you travel faster the influence of all other conditions increases which can affect the motorcycle s stability and increase the possibility of losing control Safe Riding Practices Reduce speed when The road has potholes or is otherwise rough or uneven The road contains sand dirt gravel or other loose sub stances The road is wet icy or oily The road contains painted surfaces manhole covers metal grating railway crossings or other slippery surfaces The weather is windy rainy or otherwise causing slippery or rapidly changing conditions Traffic is heavy congested not allowing sufficient space between vehicles or otherwise notflowing smoothly You are being passed in either direction by a large vehicle that may produce a wind blast in its wake When approaching a curve choose a speed and lean angle that allows you to pass through the curve in your own lane without applying the brakes Excessive speed improper lean angle or braking in a curve
118. k motion simultaneously close the throttle completely and disengage the clutch Raise the toe shift lever until you feel it stop at the next gear Simultaneously release the clutch lever and open the throttle in one smooth motion Operation Tip Within the recommended speed ranges see Recommended WARNING Shift Points chart you can downshift to slow the motorcycle or to increase power You may want to downshift when climbing a hill or passing Downshifting also helps to decrease speed when combined with closing the throttle To shift to a lower gear downshift simultaneously pull the clutch lever toward the handlebar and close the throttle Move the toe shift lever downward until you feel itstop atthe next gear Simultaneously release the clutch lever while opening the throttle Downshifting improperly could cause transmission damage loss of traction and loss of control which could result in serious injury or death Reduce speed before downshifting Always downshift within the recommended shift points Use extreme caution when downshifting on wet slippery or other low traction surfaces Release the clutch lever very gradually in these conditions Avoid downshifting in a curve Downshift before entering the curve 73 Operation Shifting Gears Recommended Shift Poi nts Upshifting Accelerating Downshifting Decelerating Gear Change Recommended Speed Gear Change Recommended Speed 1
119. l filler cap is located on the right side of the console An ornamental cap is located on the left side of the console Do not attempt to remove the ornamental cap Ornamental Cap W Do not remove 1 Turn the fuel cap counter clockwise to remove it See page 69 for fueling instructions 3 Totighten the cap turn it clockwise until the seal compresses onto the tank then continue to tighten until the cap ratchets several times N 56 To keep your motorcycle in safe operating condition always perform the recommended pre ride inspections before each ride This is especially important before making along trip and when removing the motorcycle from storage WARNING failure to perform the recommended pre ride inspections could result in component failure while riding which could result in serious injury or death Always perform the pre ride inspections before each ride When inspection reveals the need for adjustment replacement or repair perform the service promptly or see your authorized INDIAN MOTORCYCLE dealer for service WARNING Read the entire Instruments Features and Controls section of this manual before riding your motorcycle A complete understanding of the features and capabilities of your motorcycle is essential to its safe operation Anything less may result in serious injury or death Pre Ride Inspections You must be familiar with all instruments and controls to perform the pre ride inspections Tip During
120. le as our team did in building itfor you We urge you to read this rider s manual thoroughly It contains information essential to safe riding and proper maintenance of your motorcycle Your authorized INDIAN MOTORCYCLE dealer knows your motorcycle best and should be consulted for service and assistance Skilled technicians using advanced equipment and methods are best qualified to perform all major repairs and service your motorcycle may require INDIAN motorcycles comply with all federal state and local safety and emission regulations for the area of intended sale Service and Warranty I nformation Some procedures are beyond the scope of this manual See your dealer to purchase an INDIAN MOTORCYCLE Service Manual Some procedures provided in the service manual require specialized knowledge equipment and training Be sure you have the required technical skills and tools that are needed before you attempt ANY service on your motorcycle Please contact your authorized dealer before attempting any service work that is beyond your level of technical knowledge or experience or if the work requires specialized equipment Operating Your Motorcycle Outside the U S A If you plan to operate your motorcycle in countries other than the USA and Canada Service facilities or replacement parts may not be readily available Unleaded gasoline may not be available The use of leaded fuels will cause engine damage damage to your emissio
121. le so that itis stable when it rests on the sidestand 78 Parking on a Soft Surface If parking on a soft surface is unavoidable place a sidestand footrest under the foot of the sidestand to provide a firm surface The sidestand footrest must be strong enough and large enough to support the motorcycle s weight without sinking into the parking surface Asphalt becomes soft in hot weather A sidestand can sink into soft asphalt and the motorcycle may fall When parking on asphalt in hot weather use a sidestand footrest CAUTION Hotengine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components Maintenance Safety During Service Procedures AWARNING Failure to follow all recommended precautions and procedures could result in severe injury or death Always heed all safety precautions and follow all operation inspection and maintenance procedures outlined in this manual Improperly installed or adjusted components can make the Hotengine and exhaust components can cause burns to skin and motorcycle unstable or hard to handle Improperly installed can ignite a fire if exposed to flammable materials Always park electrical components can cause engine or electrical system the motorcycle clear of flammable materials and where people are failure In either event damage or serious
122. level surface Remove all riders and cargo 2 Remove the left side cover Remove the cap from the air fitting 3 Determine the recommended rear shock air pressure Refer to the label located on the inside of the left side cover 4 Install the hose fitting of the recommended gauge securely onto the air fitting Read the air pressure on the gauge 5 To reduce air pressure push the bleed button on the gauge Bleed pressure in small amounts until the desired pressure is attained 6 To increase pressure pump the handle until pressure increases to the desired amount CAUTION DO NOT exceed 150 PSI 1034 kPa in the shock 7 Remove the hose from the air fitting and reinstall the cap Tip Expect to lose up to 5 PSI 24 kPa with each pressure check 8 Repeatthe preload inspection to verify proper preload See page 88 Air Fitting Maintenance Swing Arm Rear Axle Inspection 1 Sitinthe operator s seat and slowly bounce the rear suspension a few times Make sure the suspension moves freely witnout binding Listen for abnormal noises 2 Elevate and support the motorcycle with the rear tire slightly off the floor See page 116 CAUTION Make sure the motorcycle is stable when elevated Injury may occur if the motorcycle tips or falls 3 Grasp the rear wheel and attempt to move the wheel side to side If there is movement at the front of the swingarm or in the axle area see your dealer for service 4 With t
123. lts securing the front trim bezel to the fairing Pull this piece forward to access the headlight 2 Remove the four screws securing the headlamp retaining ring Remove the retaining ring Tool Phillips screwdriver or universal tool 3 Remove the headlight assembly from the headlight carrier 4 Remove the sealing boot Press the looped end of the wire bulb retainer clip and swing the end toward the center of the bulb to release it from the latch tab 5 With the wire connector attached pull the bulb out Disconnect the wire harness 6 Install the new bulb and secure the retainer Tip Avoid touching a halogen lamp with bare fingers Oil from your skin leaves a residue causing a hot spot that will shorten the life of the lamp If a lamp is touched clean itthoroughly with denatured alcohol 7 Reinstall the sealing boot Make sure it seals tightly around the bulb base and lens to prevent condensation 8 Reinstall the headlight assembly into the carrier being sure to index the assembly properly 9 Reinstall the retaining ring with tne four screws Torque 12in lbs 1 4 Nm 10 Reinstall the front trim bezel and bolts Torque 36in Ibs 4 Nm 109 Maintenance Battery The motorcycle battery is a sealed maintenance free battery Do not remove the battery cap strip for any reason Keep the battery connections clean and tight at all times A WARNING Battery electrolyte is poisonous It contains sulfuric acid Serious burn
124. m the NAV MP3 unit will override any source of the motorcycle s audio system to ensure navigation instructions are communicated when needed The signals will also override the MP3 player e You must set volume levels within the NAV MP3 unit Volume settings in the motorcycle s audio system control NAV MP3 volume but navigation instructions may be difficultto hear if volume levels in the unit are settoo low See the GARMIN information for setting procedures The recommended initial settings are 100 80 80 MASTER 10096 NAVIGATION 8096 MEDIA 8096 Pause or stop the MP3 player to switch to radio If playing MP3 files from the GARMIN ZUMO 660 unit you may need to turn down the media volume on the GARMIN unit to avoid distortion NAV audio must be turned on in the mode menu in order to play MP3 music files from the GARMIN ZUMO 660 NAV unit While in NAV source only MP3 music stored on the GARMIN ZUMO 660 will play on the radio The power switch must be ON to use the audio system Press and release MODE until NAV is the active source When navigation instructions are f given the music volume will be 7 30 7SF muted and NAV will be displayed on the line below the active source NAV Selecting Audio Sources Bluetooth Sources Press and release MODE until BT DRIVE DEVICE is displayed on the screen Tip Make sure the BT volume on your device is turned all the way up Bluetooth Source
125. m water 6 Store the battery in a dry area with a temperature of 32 to 90 F 0 to 32 C 7 While in storage fully charge the battery once a month See page 112 Maintenance During Storage During extended storage periods maintain tire pressure and battery voltage at the recommended levels Rodents Mice and other rodents are often the worst enemy of a stored motorcycle If the motorcycle will be stored in an area where mice are a concern particularly in rural areas barns sheds etc be sure to take extra measures to deter their infestation This may include placing a screen mesh over any intake or exhaust openings just be sure to remember to remove them when you take the motorcycle from storage Park and Cover the Motorcycle 1 Park the motorcycle in its storage location Block the frame to take some of the weight off the front and rear wheels Tip Starting the motorcycle periodically during storage is NOT recommended Water vapor is a by product of the combustion process and corrosion may result unless the engine is operated long enough to bring the oil and exhaust system to normal operating temperature 2 Secure a plastic bag over the cooled exhaust outlets to prevent moisture from entering the exhaust system 3 Cover the motorcycle with a cover made from a durable breathable material designed for storage Covering the motorcycle helps protect it from dust and other airborne materials The cover must be of
126. marks by INDIAN MOTORCYCLE is under license Other trademarks and trade names are those of their respective owners Pandora is a registered trademark of Pandora Media Inc Garmin amp and zumo G are registered trademarks of Garmin Ltd or its subsidiaries JCASE amp is a registered trademark of Littelfuse Inc Printed in U S A P N 9925048 Table of Contents Introduction anaana aeaa 4 scade a E E E eae 5 Reporting Safety Defects 16 Component Identification 18 Instruments Features amp Controls 22 Pre Ride Inspections 57 Operation s 1 2 me eU WE ew S ERE GE 67 Maintenance l l 79 Cleaning and Storage 120 SDecillCallofiS 1 939 pr se sees 124 Warranty uo acci dedo e ADAC e o cce 130 Maintenance Log sss 141 Audio System CHIEFTAIN 143 lao ARD C rerr CT UTE 171 Introduction Congratulations on your purchase of a new INDIAN motorcycle You have joined an elite family of motorcycle riders who have acquired a celebrated piece of American history by choosing to own an INDIAN motorcycle Your new motorcycle is the end result of true dedication and craftsmanship by our engineering design and assembly teams It was designed and manufactured to meet our goal of providing you with a high quality motorcycle that you can ride trouble free for many years to come We hope you will take as much pride in riding your new motorcyc
127. n WARNING improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death When removing the battery always disconnect the negative black cable first When reinstalling the battery always connect the negative black cable last NOTICE Do not remove the battery cables while the engine is 1 running Doing so may damage the Electronic Control Unit ECM Take great care not to reverse the battery leads when installing the battery Reverse power applied to the ECM will damage it instantly Inspect the battery box and cover for damage Be sure pads are in good condition and properly located Make sure cable ends and battery terminals are clean Apply alight film of dielectric grease to the terminal bold threads Carefully position the battery into the battery box with the negative terminal toward the front of the motorcycle Maintenance Make sure the positive cable is routed horizontally and perpendicular to the long side of the battery Connect the positive cable to the positive battery terminal Torque 45in Ibs 5 Nm Install the negative cable last Route the starter ground cable beneath the frame ground cable on the negative battery terminal Torque 45in Ibs 5 Nm Reinstall the battery cover and fastener Torque 84in Ibs 9 5 Nm Reinstall the seat See page 106 Positive Cable 111 Maintenance Battery Charging If you
128. n Display MFD Diagnostic Functionality Certain conditions will cause an error message to display in the screen If this occurs please see your authorized dealer Instruments Features and Controls Message Location Indicates LO DC Voltage Screen Voltage remains below 11 0 volts for more than 10 seconds OV DC Voltage Screen Voltage remains above 15 0 volts for more than 10 seconds ERROR All Checksum error gauge malfunction Engine Error Codes i i E Cod Suspect Parameter The error screen displays only when the CHECK ENGINE lightis on or when it rror Code Number SPN goes on and off during one ignition cycle Error codes display only during the current ignition cycle When the power switch is turned OFF the code and message is lost but will reappear if the fault reoccurs after restarting the engine If the CHECK ENGINE indicator lamp illuminates retrieve the error codes from the display l Ifthe error codes are not displayed use the LEFT TOGGLE switch to Number 0 9 toggle until Ck ENG displays on the main line of the display 2 Pressand hold the LEFT TOGGLE switch to enter the diagnostics code E 88 88 menu 3 Record the three numbers displayed in the gear position clock and Failure Mode Indicator FMI odometer displays 4 See an authorized dealer for code details and diagnosis 31 Instruments Features and Controls Instrument Cluster CHI EF Multi Function Displa
129. ncrease speed in approximately 1 MPH 1 2 kmy h increments Press and hold the RES ACC switch to accelerate to a new set speed resets when switch is released Tip If you use the throttle to accelerate and then release it the cruise control will resume the previously set speed Cruise On Off Switch pe ks Resume or Accelerate Decelerate While cruise control is engaged tap and release the SET DEC Switch to decrease speed in approximately 1 MPH 1 2 km h increments Press and hold the SET DEC switch to decelerate to a new set speed resets when switch is released or to the minimum cruise speed of 20 MPH 32 km h Cancel Cruise Control To temporarily cancel the cruise control and allow use of the resume feature e apply the brakes or e close the throttle e disengage the clutch To cancel the cruise control and erase the set speed from memory press the cruise on off switch Decelerate 77 Operation Parking Choose a firm level surface to park the motorcycle 1 When fully stopped shift into neutral 2 Stop the engine 3 Fully extend the sidestand 4 Turn the handlebars to the left and lean the motorcycle to the left until the sidestand firmly supports the motorcycle 5 Turn the power switch off Parking on a Slope If parking on a slope is unavoidable park with the front wheel uphill from the rear wheel Place the transmission in first gear and position the motorcyc
130. nd feet protecting skin from engine and exhaust system heat Do not wear loose flowing clothing or long boot laces as they can catch on handlebars levers or footrests or they can become entangled in the wheels causing loss of control and serious injury Use of Accessories Because INDIAN MOTORYCLE cannot test and make specific recommendations concerning every accessory or combination of accessories sold the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight Use the following guidelines when choosing and installing accessories e Do nctinstall accessories that impair operator visibility or the stability handling or operation of the motorcycle Before installing an accessory be sure that it does not reduce ground clearance when the motorcycle is either leaned or in a vertical position limit suspension or steering travel or your ability to operate controls displace you from your normal riding position obscure lights or reflectors Bulky heavy or large accessories can cause instability due to the lifting or buffeting effects of wind and loss of control Safety Do not install electrical accessories that exceed the capacity of the motorcycle s electrical system Never install higher wattage light bulbs than those supplied as original equipment An electrical failure could result and cause hazardous loss of engine power or lights or dam
131. ndshield rotate the two latches upward 2 From the front of the motorcycle pull firmly on the upper windshield to remove the windshield from the upper mounts then pull the windshield upward and away from motorcycle 3 Reverse this procedure to reinstall the windshield Rotate the latches fully downward to secure the windshield WARNING Improper windshield installation can result in loss of control accident and driving hazards for other motorists if windshield falls from tne motorcycle Always make sure the windshield is fully seated before engaging latches Latches 52 Windshield Adjustment CHI EFTAI N Use the windshield switch to adjust windshield height for the best wind deflection Press the top of the switch to adjust the windshield upward Press the bottom of the switch to adjust the windshield downward Instruments Features and Controls Brakes Anti Lock Brake System ABS The anti lock brake system automatically reduces or increases brake pressure as needed to provide optimum braking control reducing the chance of wheel lock up during hard braking events or when braking on rough uneven slippery or loose surfaces See page 8 1 2 3 The anti lock brake system cannot be turned off The ABS indicator always illuminates when vehicle power is turned on It remains illuminated until the anti lock system activates which occurs when vehicle speed exceeds 6 MPH 10 kmyh When
132. ns systems and voiding of your warranty Gasoline may have a considerably lower octane rating Improper fuel can cause engine damage About the Rider s Manual Failure to follow all recommended precautions and procedures could result in severe injury or death Always heed all safety precautions and follow all operation inspection and maintenance procedures outlined in this manual All references to RIGHT LEFT FRONT or REAR are from the operator s perspective when seated in a normal riding position If you have questions about the operation or maintenance of your motorcycle after you ve read this manual please see your authorized dealer To locate the nearest authorized INDIAN MOTORCYCLE dealer visit the INDIAN MOTORCYCLE web site at www indianmotorcycle com Carefully read and understand the information found in the Safety section beginning on this page To keep your motorcycle in peak condition on the road or in storage understand and follow the procedures outlined in the Maintenance section beginning on page 79 Bring the manual along when you ride Following the precautions and procedures in the manual will add to your enjoyment and help keep you safe If you lose or damage this manual please purchase a new one through any authorized INDIAN MOTORCYCLE dealer This rider s manual should be considered part of the motorcycle and should remain with the motorcycle when ownership changes Safety Symbols and Signal Words The f
133. oir cover removed Fluid could overflow fromthe reservoir and allow air to enter the system Air in the brake system could cause the brakes to malfunction An over full reservoir may cause brake drag or brake lock up which could result in serious injury or death Maintain brake fluid at the recommended level Do not overfill NOTICE Brake fluid will damage painted surfaces and plastic parts Always clean spilled brake fluid immediately with water and a mild detergent 97 Maintenance Rear Brake Fluid Change the brake fluid atthe intervals recommended in the periodic maintenance table beginning on page 82 Always add brake fluid from a new unopened container Always use the recommended fluid See page 128 1 Position the motorcycle on level ground in the fully upright position 2 Therear brake fluid reservoir is located near the rear brake pedal View the reservoir from the right side of the vehicle 3 Wipethe fluid container and the area around the reservoir cover with a clean cloth 4 Ifthe fluid level is low inspect brake pads as outlined on page 100 If pads are not worn beyond the service limit inspect the brake system for leaks 98 5 Remove the cover and diaphragm The fluid level should be above the minimum indicator mark on the reservoir body Add brake fluid as needed Do not overfill Minimum Level Mark Sight Glass 6 Reinstall the cover and diaphragm
134. ollowing signal words and symbols appear throughout this manual Your safety and the safety of others is involved when these words and symbols are used Become familiar with their meanings before reading the manual The safety alert symbol indicates a potential personal injury hazard DANGER A DANGER indicates a hazardous situation that if not avoided will result in death or serious injury WARNING A WARNING indicates a hazardous situation that if not avoided could result in death or serious injury CAUTION A CAUTION indicates a hazardous situation that if not avoided could result in minor or moderate injury NOTICE A NOTICE indicates a situation that could result in property damage NOTE A NOTE indicates information that helps clarify procedures Safe Riding Practices Improper use of this motorcycle can result in serious injury or death to you your passenger and others To minimize the risk of injury read and understand the information contained in this section before operating the motorcycle This section contains safety information specific to the INDIAN motorcycle as well as information about general motorcycle safety Anyone who rides the motorcycle operators and passengers must follow these safety precautions Motorcycling has inherent risks You can minimize those risks but you can t eliminate them completely Even if you re an experienced motorcycle operator or passenger read all of the safety information in
135. on See page 26 GY Os Power Switch The power switch is located above the instrument gauge Press and release the power switch to enable or disable all electrical power to the vehicle See page 25 Saddlebag Lock Switch Press the lock switch to lock or unlock the saddlebags The key fob can also be used to lock or unlock the saddlebags 24 Switches Power Switch The power switch is attached to the fuel tanks on the center console Press and release the power switch to enable or disable all electrical power to the vehicle The power switch does not have to be on to start the engine See page 26 To disable all electrical power if the motorcycle is moving and the engine is running press and hold the power switch for more than three 3 seconds Tip To save battery power the vehicle will power off after five minutes of inactivity Hazard Switch The power switch must be ON to activate the flashers but once activated the flashers will continue to flash when the power switch is turned off When the flashers are active all four turn signals flash Press the switch to activate the flashers Press the switch again to cancel the flashers Instruments Features and Controls Engine Stop Run Switch Use the engine stop run switch to turn the engine off quickly Stop Press the top of the switch Run STOP to interruptthe circuits and stop the engine A The engine should not start or
136. op The action should be smooth but not loose Make sure wires hoses and control cables do not interfere with smooth steering Position the front wheel straight ahead Grasp the front forks near the front axle and attempt to move the wheel front to back If there is front to back movement at the steering head see your dealer for service If steering binds feels rough or uneven or if movement is detected at the steering stem see your dealer for service Rotate the front wheel and inspect for smooth rotation of front wheel bearings If roughness or unusual sounds are present see your dealer for service Turn handle bars full right or left and hold against the fork stop Attempt to move front wheel side to side If movement is observed see your dealer for service Maintenance Crankcase Breather Hoses Inspect both breather hoses along their length and at both ends Make sure hoses are not restricted kinked cracked or otherwise damaged Replace any worn or damaged hoses if y E 93 Maintenance Evaporative Emission Control System California M odels 1 94 Inspect all evaporative emission control system hoses and connections Make sure all connections are tight and locked The canister is located under the rear fender Make sure itis securely fastened to the mounting bracket Inspect connections at the evaporative emissions canister to be sure they are secure The ventline coming fromthe tank shoul
137. or panel Move the switch to the center position and push it inward to cancel the signal Verify that the signals and the indicator light stop flashing Repeat the procedure for the right turn signals Emergency Flashers Press the hazard switch to activate the flashers Verify that all four turn signals flash as well as the lamps on the indicator panel Turn the flashers off Verify that all signals and indicator lamps stop flashing Horn Press the horn switch Verify that the horn sounds loudly Neutral Indicator Place the transmission in neutral Verify that the neutral indicator lamp illuminates and that the letter N dis plays in the gear position display CHIEF Low Oil Pressure Display Start the engine Verify that LO OIL is not displayed in the MFD CHIEFTAIN Low Oil Pressure Display Start the engine Verify that the low oil pressure indicator is notilluminated Engine Stop Run Switch Start the engine Move the stop run switch to the STOP position Verify that the engine stops Attempt to restart the engine to verify that the engine WILL NOT start 58 Pre Ride Inspections Item Inspection Procedure General Engine Oil Check the oil level See page 60 Fuel Check the fuel level See page 65 Fluid Leaks Check the vehicle and the ground floor for any fuel oil or hydraulic fluid leaks Tires Inspect condition pressure and tread depth See page 61 Brake Operat
138. orcycle to regular use after performing service road test itin a safe environment Pay special attention to the proper fit and operation of all serviced components Make any corrections or additional adjustments necessary to ensure safe vehicle performance 80 Break In Maintenance Perform the break in maintenance procedures when the motorcycle s odometer registers 500 miles 800 km Please see your authorized dealer for this service Performing the break in maintenance will help ensure optimum engine performance for the entire service life of the engine Your dealer will change engine oil inspect all fluids and serviceable components ensure that all fasteners are tightened and make other adjustments as needed Major Maintenance Major repairs typically require technical skills and specially designed tools Emission system service requires special tools and training and should be performed by your dealer See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Periodic Maintenance Inspect clean lubricate adjust and replace parts as necessary When inspection reveals the need for replacement parts use genuine INDIAN MOTORCYCLE parts available from your dealer Record service and maintenance information in the Maintenance Log beginning on page 141 NOTICE Use of non recommended lubricants and components can result in damage to the motorcycle Damage resulting from the use of non recommended pro
139. ormation Power and Volume Controls Audio System Power Turn the power switch ON to 7 30 75F use the audio system The screen will display RADIO RADIO OFF OFF Tip To prevent battery drain when the engine is not running power will automatically turn off after 5 minutes To turn the audio system on press and release MODE or one of the volume buttons The screen will display the last active entertainment source The volume level when power is turned on will default to the level in use when power was last turned off limited to level 15 Audio System Audio System Volume Audio is active in either the speakers or the headsets The volume controls will adjust the volume in the speakers or in the driver s Bluetooth headset Tip Onsome headsets the user must press or or rotate the volume dial on the headset controls to raise or lower volume Press lt or cT to adjust volume 7 30 75F VOLUME 8 Turn the Radio Off Press and hold c until the radio 7 30 75F turns off RADIO OFF 147 Audio System Mute Push To Talk PTT Press Serr once to mute the audio system volume Press lt or c or Kt TT to un mute the audio system volume Double press SITT to activate voice recognition feature on a paired phone 148 Low Voltage M ute If the battery voltage drops to 10 5 0 5 volts the radio will mute to reduce voltage drain on the battery Full vol
140. page 92 Steering 1 Onlevel ground straddle the motorcycle and bring it to the fully upright position Turn the handlebars from stop to stop The action should be smooth but not loose 2 Make sure wires hoses and control cables do not interfere with smooth steering Rear Suspension Check the rear shock absorber mounting and inspect for leaks See your dealer for service if you discover leaks or malfunction of any kind See page 88 CHIEFTAIN only Check rear shock absorber movement and air pressure to ensure the correct amount of suspension travel and ground clearance See page 90 WARNING inadequate ground clearance could result in components contacting the ground causing loss of control and serious injury or death Always ensure ground clearance is at specification Pre Ride Inspections Rear Drive Belt 1 Check drive belttension See pages 86 87 Tip The drive belt system must be cool clean and dry to accurately measure belt tension deflection Do not measure belt tension when the belt or drive system is wet or when itis hot such as immediately after riding 2 Check the drive belt teeth for stones or other debris 3 Inspect drive belt condition See page 87 If you discover cracks broken teeth or frayed edges replace the drive belt before riding See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Fuel Level The fuel gauge displays fuel level For the most accurate re
141. questions call INDIAN MOTORCYCLE Customer Assistance United States amp Canada 1 877 204 3697 French 1 800 268 6334 134 Warranty INDIAN MOTORCYCLE Warranty Policy Motorcycle Noise Regulation Tampering with noise control systems is prohibited Federal law prohibits the following acts or causing thereof The removal or rendering inoperative by any person other than for the purposes of maintenance repair or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while itis in use or e The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person Among those acts presumed to constitute tampering are Removal or puncturing of the muffler baffles header pipes or any other component which conducts exhaust gasses Removal or puncturing of any part of the intake system Lack of proper maintenance Replacing any moving part of the vehicle or parts of the exhaust system or intake system with parts other than those specified by the manufacturer This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use Otherwise the owner may become subject to penalties under state and local ordinances Noise Emission Warranty INDIAN MOTORCYCLE warrants that this exhaust system at the time of sale meets
142. r motorcycle will not be used for a period of four 4 weeks or longer a maintenance charger should be connected to the battery A maintenance charger can be purchased through your authorized INDIAN MOTORCYCLE dea 1 112 ler Following the charger manufacturer s instructions use a battery charger designed for use with 12 volt batteries The charger should have a maximum charging rate of 1 8 amps Charge the battery for approximately 10 hours at a rate of 1 8 amps If you use a taper or trickle charger it will take longer to charge the battery After charging the battery allow the battery to sit 1 2 hours before checking the state of charge with a DC volt meter The charge should be a minimum of 12 5 DC volts Repeat the charging cycle ifthe charge isless than 12 5 DC volts Replace the battery if itfails to reach 12 5 volts after the second charge Fuse Replacement NOTICE Use fuses with the recommended amperage to avoid damage to the electrical system Standard Fuses The standard fuse box is located under the left side cover This fuse box houses all standard service fuses and the automatic circuit breakers Fuse application and size are provided on a label on the fuse box cover Tip Use the fuse puller provided in the tool kitto remove a fuse 1 Remove the left side cover See page 105 2 Release the locking tabs then squeeze the upper and lower cover clips to remove the fuse box cover 3 After replacing
143. re the o ring is in good condition 10 Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface then turn it an additional 3 4 to one full turn 11 Remove the dipstick Add only 4 5 qts 4 251 of the recommended oil at this step Do not overfill 12 Reinstall the dipstick securely 13 With the motorcycle in an upright centered position start the engine and run it at varied speeds up to 2500 RPM for approximately 3 minutes 14 Stop the engine and add an additional one quart 95 of engine oil Do not overfill Overfilling can resultin loss of engine performance and an oil saturated air filter Use a suction device to remove excess oil if overfilled Maintenance 15 To ensure the oil level is within the safe operating range re check the oil level as outlined on page 60 NOTICE After an oil change the low oil pressure indicator may illuminate when the engine is started If this occurs do not increase RPM above idle speed until the indicator turns off Operating above idle speed could result in damage to the engine 16 Dispose of used filter and oil properly 17 CHIEFTAIN Reset the oil change life in the instrument gauge See page 40 Fuel Filter The fuel filter is attached to the electric fuel pump located inside the fuel tank See your authorized INDIAN MOTORCYCLE dealer for replacement 85 Maintenance Air Filter The air box is located on the left
144. reas covered by the operation section include Engine Break In Accelerating e Fueling Braking e Starting the Engine Stopping the Engine Shifting Gears Parking Using Cruise Control if equipped Tip Even if you re an experienced motorcycle operator or passenger read all of the safety information in this manual before operating the motorcycle See page 5 Operation Engine Break In The engine break in period for your motorcycle is the first 500 miles 800 km of operation During this break in period critical engine parts require special wear in procedures so they seat and mate properly Read understand and follow all break in procedures to ensure the long term performance and durability of your engine NOTICE Failure to properly follow the engine break in procedures outlined in this manual can result in serious damage to the engine Follow all break in procedures carefully Avoid full throttle operation and other conditions that may place an excessive load on the engine during the break in period The more cautiously you treat your motorcycle during the break in period the more satisfied you will be with its performance later on Overloading the engine at low RPM and or running the engine prematurely at high RPM may result in damage to the pistons and or other engine components Observe the following precautions during the break in period Uponinitial start up do notallow the engine to idle for long periods
145. ressure is detected It will also illuminate along with the Low Battery Voltage indicator when TPMS battery power is low requiring service V Security System Locked This indicator lamp illuminates while the security system is searching for the key fob signal and when the security system is locked The lamp flashes if the key fob is not detected within range or if the fob is not programmed properly It also illuminates with the low battery voltage indicator when the key fob battery is low 35 Instruments Features and Controls Instrument Cluster CHI EFTAI N Multi Function Display MFD The power switch must be on or the engine must be running to view or change settings in the MFD Use the LEFT TOGGLE and RIGHT TOGGLE switches to toggle through the modes of the multi function display and to change settings in the display See page 27 36 RIGHT TOGGLE Active for CHIEFTAIN only 7x WAN zu i a NS Right Control I nfotainment Display There are four zones in the center display ZONE ONE 1 provides the time and outside air temperature While the units for time and temperature can be changed these items cannot be adjusted by the rider ZONE TWO 2 will always display audio system information ZONES THREE 3 and FOUR 4 will display vehicle engine information Tip Zone three can be set to display expanded audio information See page 39 1 2 3 4 7
146. rs Pinch Bolts C 18 19 ft lbs 24 4 25 7 Nm Axle Bolt 52 ft lbs 70 Nm Wheel Spacers 0 925 in 23 5 mm f Tires Operating the motorcycle with incorrect tires incorrecttire pressure or excessively worn tires could cause loss of control or accident Underinflation can cause a tire to overheat and result in a tire failure Always use the correct size and type of tires specified by INDIAN MOTORCYCLE for your vehicle Always maintain proper tire pressure as recommended in the rider s manual and on safety labels Tire Replacement NOTICE On models equipped with a TPMS the sensors are located 180 fromthe valve stem Use caution when servicing tires To avoid damaging a sensor break the bead at the valve stem then at 90 and 270 fromthe valve stem as required Tires rims innertubes and air valves must be correctly matched to wheel rims Use only the proper size tires specified with the same or higher load ratings INDIAN MOTORYCLE recommended tires provide proper clearance between fenders swingarm drive belts and other components See the Specifications section beginning on page 124 On models equipped with innertubes innertubes MUST be replaced with new innertubes when tires are replaced Use only the proper size innertubes WARNING Mismatched tires rims and air valves may result in damage to the tire bead during mounting or may allow the tire to slip off the rim possibly resulting in tire fail
147. ruise control could cause loss of control and result in serious injury or death Follow all cruise operation procedures carefully Never use cruise control when roads are wet or slippery Do notuse cruise control when riding in heavy or congested traffic 76 Cruise Control Tips Cruise control can be set in gears 4 6 Vehicle speed must be above 20 MPH 32 km h Set speed will vary slightly in hilly terrain Cruise control will not resume a pre set speed if the resulting acceleration or deceleration rate is too high or too low For example resuming a set speed from 40 MPH 64 kmy h while in 6th gear may cause cruise to disengage Cruise control will not engage if brake lights are not operating properly The clutch or either brake must have been activated at least once since the engine was started for the cruise control to function Using Cruise Control Set Speed 1 Press and release the cruise on off switch The amber cruise control indicator will illuminate in the instrument cluster Cruise control is enabled but not set 2 Accelerate to the desired speed and press the SET DEC switch The green cruise control indicator Set lamp will illuminate Cruise control is set to the desired speed Resume Speed After disengaging the cruise control with the brake throttle or clutch press the RES ACC switch to return to the set speed Accelerate While cruise control is engaged tap and release the RES ACC switch to i
148. s can result from contact with skin eyes or clothing Antidote External Flush with water Internal Drink large quantities of water or milk Follow with milk of magnesia beaten egg or vegetable oil Call physician immediately Eyes Flush with water for 15 minutes and get prompt medical attention Batteries may produce explosive gases Keep sparks flame cigarettes etc away Ventilate when charging or using in an enclosed space Always shield eyes when working near batteries KEEP OUT OF REACH OF CHILDREN 110 Battery Removal 1 Remove the seat See page 106 WARNING Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death When removing the battery always disconnect the negative black cable first When reinstalling the battery always connect the negative black cable last 2 Remove the fastener securing the battery cover to the frame crossmember 3 Liftthe cover with the attached electronic module in place folding the wires toward the fuel tank Tool 5 mm hex key wrench 4 Remove the negative battery cable from the battery terminal Position the cable well clear of the terminal Tool 10 mm wrench 5 Remove the rubber cover from the positive battery cable and remove the cable from the terminal Position the cable well clear of the terminal 6 Remove the battery Negative Positive Battery Installatio
149. side the left down tube Slide the rubber protective cover away fromthe lock nut Loosen the lock nut While holding the cable turn the cable adjuster inward or outward until clutch lever freeplay is 0 5 1 5 mm While holding the cable tighten the adjuster lock nut securely PER eee S CA y 02 059 in Clutch 0 5 1 5 mm Lever Freeplay Verify that the safety switch activates properly The engine should not start in gear with the clutch lever released Tip The starter interlock switch is dependent on the clutch lever freeplay being set correctly to ensure activation of the clutch safety switch 95 Maintenance Mechanical Clutch Lever Lubricati on 1 The clutch cable adjuster nut is located alongside the left down tube Slide the rubber protective cover away from the adjuster Loosen the lock nut 2 Turnthe cable adjuster completely inward to provide maximum lever freeplay 3 Remove the clutch lever 5 c clip and pin Disconnect the clutch cable from the clutch lever 4 Remove any old grease and dirt from the lever and housing Lubricate the clutch lever and pin with moly assembly grease or all purpose grease Cluth C Clip Cable 5 Reconnectthe clutch cable Reinstall the lever c clip and pin 6 Adjust clutch lever freeplay See page 95 7 Tighten the adjuster nut and slide the protective cover over the adjuster 96 Mechanical Clutch Cable Lubrication
150. sition Roll the grip rearward to open the throttle increase engine speed and power Roll the grip forward to close the throttle decrease engine speed and power The control grip is spring loaded When you release the grip the throttle returns to the idle position Decrease Speed AR ry Increase Speed 48 Clutch Lever The clutch lever is located on the left handlebar Disengage the clutch before shifting gears For smooth clutch operation pull the lever quickly and release itina brisk but controlled manner To disengage the clutch pull the lever toward the handlebar e To engage the clutch release the lever in a brisk but controlled manner Clutch Lever Gear Shift Lever The gear shift lever is located on the left side of the motorcycle Operate the lever witn your foot Press downward on the toe lever to shift to a lower gear e Lift upward on the toe lever to shift to a higher gear Release the lever after each gear shift See pages 72 74 for gear shifting procedures Instruments Features and Controls Mirrors Your vehicle is equipped with convex mirrors Objects seen in a mirror may be closer than they appear Always adjust mirrors before riding To adjustthe mirrors siton the motorcycle in the anticipated riding position Adjustthe mirrors so that you can see a small portion of your shoulders in each mirror Tire Pressure Monitoring System TPMS
151. te the high beam press the upper portion of the switch To activate the low beam press the lower portion of the switch The headlights operate only when the engine is running You can use the high low headlight beam switch to override this function and allow the headlights to operate when the engine is not running Turn the power switch on then toggle the high low headlight beam switch to turn the headlights on Auxiliary Light Switch The auxiliary lights provide additional lighting on each side of the headlight Some drivers prefer using the auxiliary lights when operating in foggy conditions or when passing a vehicle to help improve visibility to other motorists Press the auxiliary light switch to turn the auxiliary lights on or off The auxiliary lights turn off when the power switch is turned off The auxiliary lights automatically turn on when the engine starts if they were on when the engine was shut down 27 Instruments Features and Controls Instrument Cluster CHI EF The instrument cluster includes the speedometer indicator lamps and Multi Function Display MFD Speedometer Speedometer Indicator Lamps The speedometer displays forward vehicle speed in either miles per hour or kilometers per hour Indicator Lamps Indicator Lamps Lamp Indicates Condition Turn The turn signal indicator flashes when the left 40 Lamp Indicates Condition Neutral Z The
152. ted by your dealer and submitted to INDIAN MOTORCYCLE within ten days of purchase Upon receipt of this registration INDIAN MOTORCYCLE will record the registration for warranty No verification of registration will be sentto the purchaser as the copy of the Warranty Registration Form will be your proof of warranty coverage If you have not signed the original registration and received the customer copy please contact your dealer immediately NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR MOTORCYCLE IS REGISTERED WITH INDIAN MOTORCYCLE Initial dealer preparation and set up of your motorcycle is very important in ensuring trouble free operation Purchasing a vehicle in the crate or without proper dealer set up will void your warranty coverage 130 Warranty INDIAN MOTORCYCLE Warranty Policy WARRANTY COVERAGE AND EXCLUSIONS LIMITATIONSOF WARRANTIES AND REMEDIES This INDIAN MOTORCYCLE limited warranty excludes any failures that are not caused by a defectin material or workmanship THIS WARRANTY DOES NOT COVER CLAIMS OF DEFECTIVE DESIGN This warranty also does not cover acts of God accidental damage normal wear and tear abuse or improper handling This warranty also does not cover any motorcycle component or partthat has been altered structurally modified neglected improperly maintained or used for purposes other than for which it was designed This warranty excludes damages or failures resulting from improper lubrication improper engine
153. the front up and over the lower triple clamp using care to not interfere with wiring and brake lines Place tiedowns as wide apart as possible on the truck or trailer bed for best stability 14 Fuel and Exhaust Safety Always heed these fuel safety warnings when refueling or servicing the fuel system For fueling procedures see page 69 A WARNING Gasoline is highly flammable and explosive under certain conditions Always exercise extreme caution whenever handling gasoline e Always turn off the engine before refueling Always refuel outdoors or in a well ventilated area e Open the fuel cap slowly Do not overfill the tank Do not fill the tank neck Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored Gasoline and gasoline vapors are poisonous and can cause severe injury e Do not swallow gasoline inhale gasoline vapors or spill gasoline If you swallow gasoline inhale more than a few breaths of gasoline vapor or get gasoline in your eyes see a physician immediately If gasoline spills on your skin or clothing immediately wash it off with soap and water and change clothing Exhaust gases contain carbon monoxide a colorless odorless gas that can cause loss of consciousness or death in a short time Never startthe engine or letitrun in an enclosed area Never inhale exhaust gases Safety Safety Maintenance AWARNING Failure
154. the turn signal switches to unlock the security system See page 114 26 Saddlebag Lock Switch If your model is equipped with electric saddlebag locks the locks can be controlled by either the key fob or the lock switch on the console When using the console lock switch the key fob must be within range If the key fob is not detected the security light and or power switch will flash The system will not perform the lock or unlock command Unlock Lock Saddlebag Lock Switch Key Fob Switches Ignition Light Switch The headlights automatically come on when the engine is started WARNING Motorcycle riders must remain as visible as possible at all times To aid in this the headlight must be on at all times Do not modify the ignition light switch wiring to circumvent the automatic headlight feature Toggle Switches All models are equipped with toggle switches on the front side of the left and right handlebar controls The LEFT TOGGLE switch is active for all models The RIGHT TOGGLE switch is active only for CHIEFTAIN models The power switch must be ON Use the switches to toggle through the modes of the multi function display and to change settings in the display RIGHT TOGGLE Active for CHIEFTAIN only LEFT TOGGLE P hne Instruments Features and Controls High Low Headlight Beam Switch The high low headlight beam switch toggles the headlight between high beam and low beam To activa
155. these parts The owner is responsible for the performance of all required maintenance Such maintenance may be performed ata service establishment or by any individual The warranty period begins on the date the motorcycle is delivered to an ultimate purchaser INDIAN MOTORCYCLE COMPANY P O Box 47700 Hamel MN 55340 9960 ATTN Warranty Department 140 Maintenance Log Maintenance Performed Miles Km Notes Performed by 141 Maintenance Log Maintenance Performed Miles Km Notes Performed by 142 Audio System Introduction Not all motorcycles are equipped with an audio system Motorcycles equipped with an audio system may not be equipped with all components discussed in the audio section of this manual Components not installed at the factory can be purchased from and installed by your INDIAN MOTORCYCLE dealer WARNING Distracted driving can result in loss of control collision or accident which may result in serious injury or death Avoid using any features and devices while driving that may take your attention away from the road and safe driving habits even for a moment Always keep both hands on the handlebars When device operation is necessary please use voice activated devices Made for iPod iPhone 3 Bluetooth Works With PANDORA Audio System iPod
156. this manual before operating the motorcycle Take a rider education course from the Motorcycle Safety Foundation or another qualified instructor The course will help you develop or refresh your expertise in safe riding habits through instruction and riding For information on Motorcycle Safety Foundation rider education courses in your area call 1 800 446 9227 or visit www msf usa org Read and understand all information in this rider s manual Observe all maintenance requirements specified in this manual See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Design characteristics affect how you should ride the motorcycle The motorcycle is designed for on road use with one rider and one passenger Never exceed the GVWR or the GAWR Refer to the Specifications section of this manual page 124 or the Manufacturing Information VIN label on the motorcycle frame for model specific information Riding off road riding with more than one passenger or carrying weight exceeding the maximum weight rating can make handling difficult which could cause loss of control During the first 500 miles 800 km of operation follow all break in procedures as outlined in the break in section beginning on page 67 Failure to do so can result in serious engine damage Some models include saddlebags a windshield or a passenger backrest as standard equipment To maintain stability be prepared to reduce the operatin
157. timing improper fuel surface imperfections caused by external stress heat cold or contamination operator error or abuse improper component alignment tension adjustment or altitude compensation snow water dirt or other foreign substance ingestion contamination improper maintenance modified components use of aftermarket or unapproved components accessories or attachments unauthorized repairs or repairs made after the warranty period expires or by an unauthorized repair center This warranty excludes damages or failures caused by abuse accident fire or any other cause other than a defect in materials or workmanship and provides no coverage for consumable components general wear items or any parts exposed to friction surfaces stresses environmental conditions and or contamination for which they were not designed or notintended including but not limited to the following items Wheels and tires Filters Fuel Injectors Throttle body components Suspension components Lubricants Engine components Brake components Bushings Drive belts Seatcomponents Sealants Hydraulic components and fluids Clutches and components Coolants e Circuit breakers Fuses Steering components Bearings Electronic components Batteries Finished and unfinished surfaces Spark plugs e Lightbulbs Sealed beam lamps 131 Warranty INDIAN MOTORCYCLE Warranty Policy LUBRICANTS AND FLUIDS 1 Mixing oil brands or using non
158. to perform safety maintenance as recommended can result in difficult handling and loss of control which could result in serious injury or death Always perform the safety maintenance procedures as recommended in this manual Perform maintenance and repairs promptly See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Before each ride perform the Pre Ride Inspections See page 57 Perform all periodic maintenance at the recommended intervals outlined in the Periodic Maintenance section beginning on page 81 Always maintain proper tire pressure tread condition and wheel and tire balance Inspect tires regularly and replace worn or damaged tires promptly Use only approved replacementtires See the Specifications section beginning on page 124 Always ensure proper steering head bearing adjustment Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage Make any necessary repairs promptly See page 93 Clean the motorcycle thoroughly to reveal items in need of repair Fasteners must meet original specifications for quality finish and type to ensure safety Use only genuine INDIAN MOTORYCLE replacement parts and ensure that all fasteners are tightened to the proper torque Electromagnetic Interference This vehicle complies with European directive 97 24 EC Chapter 8 requirements which is equivalent to Canadian ICES 002 15 Gross Vehicle Weight Rating GVWR WA
159. to the end of Teeth Sensor the wheel speed sensors If contamination is observed or if you are unable to visually inspect slide a thin towel across the face of the sensor between the sensor and the tone ring to remove any potential debris 101 Maintenance Wheel Spokes Inspect both wheels for loose bent broken or missing spokes if equipped To identify loose spokes grasp each spoke and try to move it side to side or up and down All spokes should be equally tight and have the same amount of flex Tighten loose spokes and replace bent broken or missing spokes see an authorized dealer WARNING Spokes adjusted or replaced improperly could distort the wheel make the motorcycle difficult to handle and cause loss of control Wheel I nspection Inspect both wheels for cracks or damage and replace damaged wheels promptly Do not operate the motorcycle if wheels are damaged or cracked See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Wheel Alignment Inspect rear wheel alignment at regular service intervals whenever the rear wheel is removed and when the rear drive beltis adjusted Please see your dealer for this service 102 Front Wheel Installation If the front wheel is removed for any reason it must be Fork reinstalled in the correct rotating direction Clean all wheel components before installation Apply a light coat of all purpose grease to the axle and both space
160. to2 15 MPH 24 kmy h 6to5 40 MPH 64 km h 2to3 25 MPH 40 km h 5to4 35 MPH 56 km h 3to4 35 MPH 56 km h 4to3 25 MPH 40 km h 4to5 45 MPH 72 kny h 3to2 15 MPH 24 km h 5to6 50 MPH 80 km h 2to1 10 MPH 16 km h 74 Braking Always allow sufficient stopping distance so that brakes can be applied gradually Tip Applying slightly more front brake than rear brake generally provides the best braking performance 1 To slow the motorcycle with the brakes close the throttle and apply the front and rear brakes evenly and gradually Tip When the anti lock brakes engage during a braking event the rider will feel pulsing at the brake levers Continue to apply steady pressure to the brakes for the best stopping performance 2 Asthe motorcycle slows disengage the clutch or downshift each time vehicle speed reaches a downshift point WARNING Braking improperly could result in loss of control which could result in serious injury or death Avoid braking abruptly Always apply the brakes gradually especially on wet slippery or other low traction surfaces Avoid braking in a curve or turn Bring the motorcycle to the upright position before applying the brakes Operation Accelerating Accelerate by opening the throttle rolling the throttle control grip rearward For even acceleration open the throttle with a smooth continuous motion When you reach the recommended speed for upshifting shift up one gear
161. transmission is in neutral High Beam 0000 D The headlight switch is set to high beam This indicator will flash if there is a problem with the low or high beam light Signal right or both turn signals hazard are active If there is a problem in the signal system the lamps will flash at twice the normal rate wW Cruise Amber Lamp Cruise control is enabled but Control not set Green Lamp Cruise control is setto Status the desired speed Read the safety and operation procedures before using cruise control See page 76 Check If this lamp illuminates while the engine is CU Engine running see your dealer promptly The light will remain on if the tilt sensor shuts down the engine If abnormal sensor or engine operation is detected the light will remain on as long as the fault condition exists Retrieve the error codes for diagnosis See page 31 Anti Lock The indicator remains on until the anti lock Brakes system activates which occurs when vehicle Not speed exceeds 6 MPH 10 km h When the Activated lamp is illuminated the anti lock brakes will not activate but the conventional brake system will continue to operate normally When standard mode is selected speed Vehicle displays in miles per hour Speed 28 When metric mode is selected speed displays in kilometers per hour Instrument Cluster CHI EF Multi Function Display MFD The power switch must be ON to acc
162. turated air filter Use a suction device to remove excess oil if overfilled Tip The approximate volume between the ADD and FULL marks on the dipstick is 32 oz 941 9 Repeatsteps 1 7 to ensure the level is within the safe operating range 10 Reinstall the dipstick securely Nous Tires WARNING Operating the motorcycle with incorrect tires incorrect tire pressure or excessively worn tires could cause loss of control or accident Underinflation can cause a tire to overheat and result in a tire failure Always use the correct size and type of tires specified by INDIAN MOTORCYCLE for your vehicle Always maintain proper tire pressure as recommended in the rider s manual and on safety labels Tire Pressure Improper tire pressure can result in irregular tire wear tire failure reduced fuel economy and a poor riding experience It can also affect handling and stopping ability Slow tire pressure loss over time is normal for a functional tire Although a tire pressure monitoring system TPMS will alert the user to alow pressure condition if equipped always inspecttire pressure and condition before each ride Check tire pressure before riding when the tires are cold This will provide the most accurate reading as riding warms the tires and increases tire air pressure Tires remain warm for atleast 3 hours after a ride Do not adjust tire pressure immediately after riding As tires cool the pressure will drop and result in
163. ume will be restored when the battery voltage returns to 11 5 12 5 volts If battery voltage drops 7 30 75F MUTE LOW VOLTAGE below 8 5 volts the radio will turn off Radio function will not be available until the battery is fully charged Audio System Selecting Audio Sources Press MODE repeatedly to choose the desired audio source WX Weather source 7 30 75F Each press changes the audio source as follows North America models only Eua 1 e FM WX 1 AM e MW Europe only USB sources 7 30 75F e LW Europe only All models USB WX Weather North America only Flash memory connected ARTIST USB SONG TITLE NAV If enabled iPhone iPod connected Bluetooth Driver if enabled 7 30 75F iPod FM source 7 30 75F ARTIST All models shown with RBDS FULL FM 93 7 SONG TITLE 93X Pandora on iPhone iPod only 7 30 75F ARTIST Pandora is currently available only 3 in the United States Australia and PANDORA New Zealand ARTIST AM source 7 30 75F SONG TITLE All models excluding Europe S MINER OE AM 1500 149 Audio System Selecting Audio Sources MW Medium Wave SUID 7 30 75F Europe models only MW 531 LW Long Wave source 7 30 75F Europe models only LW 153 NAN SOUNGE 7 30 75F All models skipped if not enabled NAV BT Driver source All models skipped if not 7 30 TOF enabled GARY S IPOD 150
164. ure Maintenance Tire Condition Inspect the tire sidewalls road contact surface and tread base for cuts punctures and cracking Replace damaged tires immediately See the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer Tire Tread Depth Replace any tire with a tread depth of less than 1 16 inch 1 6 mm Tread wear indicators are located in atleast six places on the tread circumference and become visible at a tread depth of approximately 1 16 inch 1 6 mm The tread wear indicators appear as a solid band across the tread You may also use a depth gauge or an accurate ruler to measure the depth of the center tire tread on both front and rear tires 103 Maintenance Tires Tire Pressure Always check and adjust tire pressure when tires are cold Do not adjust tire pressure immediately after riding Wait atleast 3 hours after riding to check pressure If pressure checked and adjusted while tires are warm the pressure will drop as tires cool and result in underinflation Adjust tire pressure as recommended for the total weight of your intended load see chart below For more information refer to the manufacturing information label located on the front frame downtube See page 17 WARNING Do not exceed the maximum recommended inflation pressure to seat the bead Tire or rim failure may result Recommended Pressure Location Size Brand Type Loads
165. ures and Controls Instrument Cluster CHI EFTAI N Indicator Lamps Lamp Indicates Condition NI Neutral The transmission is in neutral and the power switch is ON When standard mode is selected speed displays in miles per hour Vehicle Speed When metric mode is selected speed displays in kilometers per hour BO High Beam The headlight switch is setto high beam This indicator will flash ifthere is a problem with the low or high beam light Low Oil This lamp illuminates when oil pressure drops below a safe operating pressure while the engine is running If Pressure this lamp illuminates while the engine is running above idle speed turn the engine off as soon as safely possible and check the oil level If the oil level is correct and the lamp remains on after the engine is restarted turn the engine off immediately See your dealer Low Fuel This lamp illuminates when approximately one gallon 3 8 liters of fuel remains in the fuel tank The LCD Display will switch into a Low Fuel Mileage Counter Mode to provide the rider with mileage tracking from the time the indicator was activated Turn Signal One arrow flashes when the corresponding turn signal is activated Both arrows flash when the hazard signal is activated If there is a problem in the signal system the lamps will flash at twice the normal rate 34 Instruments Features and Controls Instrument Cluster CHIEFTAIN
166. utch If the power switch is ON the neutral indicator illuminates when the transmission is in neutral Shifting Gears While Stationary To locate neutral when the motorcycle is stationary use one of the following techniques to load and unload the transmission shift dogs which allows them to disengage 1 With the clutch disengaged lever pulled inward shift into neutral while rocking the motorcycle forward and rearward 2 With the transmission in first gear gently release the clutch until it just begins to engage Apply upward pressure on the toe lever and quickly pull the clutch inward To shift gears when the motorcycle is stationary engine may be running or stopped disengage the clutch and apply slight pressure on the shift lever while rocking the motorcycle forward and rearward Shif ng Gears Shif ng Gears While Driving 1 2 3 vi Start the engine See page 70 With the engine at idle speed apply the front brakes Disengage the clutch pull the clutch lever fully toward the handlebar Push the toe lever downward until you feel it stop in first gear Release the brake lever Simultaneously release the clutch lever while opening the throttle rolling the throttle control grip rearward in one smooth motion As the clutch begins to engage the motorcycle will move forward To shift to a higher gear accelerate smoothly to the recommended shift point See Recommended Shift Points chart With a quic
167. y MFD Low Oil Pressure Display LO OIL displays under the following conditions Condition Indicates Action Required ig AT MIT AUT RR ERE F Engine oil pressure Oil pressure is below a Stop the engine as soon as safely possible A I j F1 F1 ij has dropped while the safe operating pressure and check the oil level If the oil level is I M i T4 ii fi engine is running sufficient but LO OIL continues to display after restarting the engine stop the engine immediately S Ie 3 Hu P 32 Instrument Cluster CHIEFTAIN The instrument cluster includes the speedometer tachometer fuel gauge indicator lamps and multi function display MFD Indicator Lamps Speedometer Tachometer Multi Function Display Fuel Gauge Instruments Features and Controls Speedometer The speedometer displays forward vehicle speed in either miles per hour or kilometers per hour Tachometer The tachometer displays engine speed in revolutions per minute RPM A red line on the face of the gauge indicates the maximum safe engine speed Excessive engine speed can cause engine damage or failure which could result in serious injury or death Do not allow engine speed to exceed the red line Fuel Gauge The fuel gauge displays fuel level For the most accurate reading sit on the motorcycle and bring it to the upright position 33 Instruments Feat

Here - Polaris

Contents

Download Pdf Manuals

Related Search

Related Contents