Home

Service Instructions Jede 1200E

1. Selecting a submenu If you have selected a main menu with one or more submenus with button 3 above you will automatically go to the first submenu after pressing the button The display may show for example Price PROG A 21 Ingredient Key 1 Price LJ Use button 1 to scroll through the submenus Use button 2 to go back through the list LJ Use button 3 to select the submenu that is shown and the parameter value will be displayed LI Q Use button 4 to return to the previous main menu End programming LJ Press button 6 when in the relevant main menu the LED will show green to leave the machine s programming mode Any changes will only be stored after button 6 has been pressed GB You must be at the main menu when pushing button 6 Ifyou want to undo a change or cannot remember what has been changed you can disconnect the power to prevent the changes from being saved Ifthe plug is taken out like this the door must be closed before the plug is put back in Otherwise the machine will start up in the service mode Service Instructions Jede 1200E rev 02 Programming It takes a few seconds for the data to be stored and during this time the display is turned off If you have pressed button 6 or disconnected the power the menu panel buttons will change back into drink selection but tons after restart Changing parameters If you have selected a menu submenu with button 3 you will automa
2. answer system or BM PVB Service Instructions Jede 1200E rev 02 CHAPTER 3 45 Troubleshooting Error Description Cause Remedy code E19 Internal fault local I Shorting bar J11 missing on door U Check shorting bar J11 adjacent program processor BM card ming button LJ Data error in PC Board BM U Change E21 Coin tube activated U A coin or objekt is stuk in the coin U Clear the tube tube LJ Press the coin return button U There may be magnetic object or U Dismantle coin dispenser and remove any rub rubbish in the coin dispenser bish LJ The coin dispenser is full LJ Empty the coin box U The coin mechanism defective U Replace the coin mechanism LJ Poor fit between the coin tube and UW Check that the opening of the coin tube is the coin dispenseer lined up with the input of the coin dispenser E22 Timout initiating The display has no communication Check the communication with the BM or TM PCB E23 Timeout serving Cannot be shown The error is self cor recting E24 Display error no answer The display broken Change it MDB change giver not responding MDB billvalidator no answer MDB Keyreader no answer MDB Universal slave no answer Change giver defective The billvalidator broken The card reader is broken The slave is broken Change it Change it Change it Change it E29 EEPROM write read EEPROM is broken Change the BM PCB error E30 No respon
3. Increase pressure if possible Otherwise increase amount of water via menu 21 6 See Error codes E10 E11 Remove limescale and dirt Replace kinked hose CHAPTER 3 48 Service Instructions Jede 1200E rev 02 Troubleshooting Water not flowing LJ Faulty outlet valve or circuit board U Check first that connection between the circuit out into cups board and the outlet valve look right Measure the voltage at the outlet valve when ordering a drink If voltage is below 20 V the circuit board is defective and needs changing If the voltage is 20 25 V and the outlet valve does not open the valve is defective and needs changing See section Replacing the outlet valve U Water tank empty U See Error codes E10 E11 Service Instructions Jede 1200E rev 02 CHAPTER 3 49 Assembly description Replacing the inlet valve The water tank is mounted on a movable bracket inside the machine Remove the carousel to access the inlet valve Removing the carousel AN Take the plug out of the wall socket 1 Start by removing all the cup stacks Make a note of their positions in the carousel 2 Unscrew the knob in the middle of the cup carousel 3 Turn the carousel so the markings on the dispenser arm are aligned with one of the cup dispensers 4 Lift out the carousel upw
4. 14 43714 Kabelsats additivmodul Wire harness cartridge module 1 Service Instructions Jede 1200E rev 02 CHAPTER 4 89 CE Doc No 36 544 E 4 rev 02 We reserve the right to make alterations Gematech Innovation
5. if the machine contains a coin dispenser total number of sales total number of sales per drink and total number of errors per error code See also Menus below authorisation A Recipe programming As the standard version of this machine contains cups with the correct amount and type of ingredient their compositions cannot be changed The amount of water and whether the high pressure pump should be activated can be set from here however Service Instructions Jede 1200E rev 02 System overview As an optional extra the machine can be fitted with drink supple ments in the form of powder cartridges Programming with these supplements reguires authorisation B See also Menus below authorisation B System programming From here you can edit whether the default setting should apply select the country and coin table to use set the water temperature in the tank and reset all statistical information See also under Menus below authorisation C The machine s functional modes The machine has three different states or functional modes U Operating mode I Service mode U Programming mode Operating mode Setting Put the plug into the wall socket with the door of the machine closed When it has powered up data is read from E PROM and stored in RAM To speed up reading and writing to E PROM nothing else is done during this time The display cannot be updated and is turned off During the ver
6. 4 O ring silicon 13 6 x 2 4 2 8 46046 Nippel Nippel 2 9 47841 Plugg Plug outlet hose 1 10 43225 Tanklock med terg ng Tank cap with override 1 11 43981 T tning Seal tank 1 12 46034 L sbricka Lock washer 2 13 43442 Pumpsystem med filter och by pass Pumpsystem with filter and by pass 1 14 42759 Silikonslang diam 7 5 mm Silicon hose diam 7 5 mm 1 15 43626 Tank JEDE 1200 Tank JEDE 1200 1 16 45185 Clips Clip 1 17 36207 Tankh llarpl t Carrier for tank 1 18 49374 Clips Clip 1 19 43994 Servicelucka Service hatch 1 20 46253 Inloppsventil Inlet valve 1 lt gt 49064 1 Temperatursensor NTC Temperature sensor NTC 1 Service Instructions Jede 1200E rev 02 CHAPTER 4 83 Electronic box Elektroniklada CHAPTER 4 84 Service Instructions Jede 1200E rev 02 Electronic box Elektroniklada 07 11 Pos No Part No Ben mning Term Antal Oty 1A 47292 Kopplingdplint front Connection bridge front 1 1B 47293 Kopplingsplint gavel Connection side 1 2 43402 Transformator 80 VA Transformer 80 VA 1 3 43749 2 Styrkort TM 3 PC board TM 3 1 4 36080 2 Lock Cover 1 5 47291 Apparatintag med avst rningsfilter Power inlet with supression f lter 1 6 36079 Elektronikl da Box 1 Z 46417 F ste f r styrkort Pin for PC board 4 8 35299 Kabelklammer Cable tie 1 Service Instructions Jede 1200E rev 02 CHAPTER4 85 Cup presenter B garpresentat r CHAPTER 4 86 Service
7. Cointube status takes you to the first coin tube in the coin dispenser 0 05 on the display shows that eran ne K the coin tube holds 5 eurocent or others coins 2 im If you want to fill up this coin type or alternatively empty the coins into the coin PROG C 8 box accept with button 3 Otherwise continue with button 1 to the next coin AS ODE s NbrOfCoins 0 05 u tube The last line of the display now shows the number of coins in the coin tube 10 e g 10 Refilling the coin tube 3 Fill up with 5 eurocent coins The number 10 increases as each coin is inserted Emptying coins into the coin box 3 m Press button T to empty the coins into the coin box The number 10 decreases with each press 4 n Press button 3 to proceed to the next coin tube or press button 6 to end E The change is now implemented and stored It takes a few seconds for the data to be stored If the door is closed the buttons on the menu panel go back to being drink selection buttons AN You must be at the main menu when pushing button 6 This programming example can also be found in the Operator s Manual Service Instructions Jede 1200E rev 02 CHAPTER 2 35 Programming Programming example Changing the number of doses for a drinks cartridge being exchanged Relevant when adjusting the standard values for the cartridges under the current loading programme Main menu 72 Nbr cups dosages Sub
8. Instructions Jede 1200E rev 02 Cup presenter B garpresentat r 07 11 Pos No Part No Ben mning Term Antal Qty 1 36075 Spillbricka Spilltray 1 2 OV1750 Flott r Float 1 3 48935 1 Flott rstyrning Giude float 1 4 46047 O ring silikon 13 6 2 4 O ring silikon 13 6 2 4 1 5 43370 Skruv 4 3 x 20 Screw 4 3 x 20 1 6 43539 1 Lock Cover 1 6 36093 Lock 73 5 mm Cover 73 5 mm 1 7 43538 Cylinder Cylinder 1 8 43171 Axel 10x70 Shaft 10x 70 1 9 43416 Magnet 8x5 Magnet 8x5 3 10 43852 B garpresentat r komplett Cup presenter complete 1 10 36094 B garpresentat r komplett 73 5 mm Cup presenter complete 73 5 mm 1 Service Instructions Jede 1200E rev 02 CHAPTER4 87 10 Additive module Additivmodul CHAPTER 4 88 Service Instructions Jede 1200E rev 02 Additive module Additivmodul 02 10 Pos No Part No Benamning Term Antal Qty 1 44023 Dragslid plast additivmodul Slide cartridge module 4 2 45447 Motorf ste plast 2 fack Motor bracket plastic 2 3 43501 2 H llare additivmodul carrier cartridge module 1 4 43500 H llare tratt Holder funnel 1 5 XX Patroner Cartridges 4 6 43607 Tratt additiv Funnel 8 48691 Dispensermotor Dispensing motor 48775 4 Vevsl ng svart Crank black 4 10 43116 Skruv Screw 12 i 30085 Skruv Screw 8 12 42542 Mikrobrytare motor Microswitch motor 4 13 30071 Skruv Screw 8
9. cover plate and remove it See figure The water tank bottom will now be visible 3 Locate the overheating protection as shown in figure and press the reset button with a screwdriver 4 Refit the carousel 5 Close the door 6 Put the plug back in 1 Cover plate 2 Service cover 3 Bottom part of the water tank 4 Overheating pretection 5 Reset button CHAPTER 3 60 Service Instructions Jede 1200E rev 02 Wiring diagram Element ER o i TANKMODUL 43749 z o ee Vacuum tube Ballast BEORDRINGSMODUL SERVERINGSMODUL em 49050 Suppression Filter 48041 Overwiev of the modules Photoswitch Carousellposition Photoswitch Cup in carousell Steppingmotor Cuprotator Cup in disp position 0 Photoswitch Cup in customerpos LI Photoswitch Steppingmotor Carousell 48042 S Module 1200 48050 J3 J4 J5 J7 J8 J9 Service Instructions Jede 1200E rev 02 CHAPTER 3 61 Wiring diagram Microswitch Drip tray gt Electromagnetic locking device for cupserver Cupdispensing motor Hallsensor Cupserver position 48043 S Module 1200 48050 J10 J11 J12 CoinmedAlternative Validator Alternative oJ 48044 BM3 Module 1200 43744 J3 J4 CHAPTER 3 62 Service Instructions Jede 1200E rev 02 Display Pushbutton panel Coinme
10. followed and that the machine has been used with JEDE s drinks for which it is designed The guarantee ceases to apply if original parts are not used and JEDE AB cannot accept responsibility for any damage resulting from or in connection with the use of parts that are not original A guarantee note is enclosed with every machine Follow the instructions on it Weight Height machine Width Depth Voltage Current Power Control voltage Tank Capacity Connection pressure water Service Instructions Jede 1200E rev 02 98 kg excl Cup stacks cartridges and payment mechanism 1830 mm 650 mm 600 mm 230 240 V 10 A external fuse 2100W 24VDC Volume 2 5 litres 11 cup stacks 4 JEDEMATIC cartridges 0 2 6 0 bars CHAPTER 3 65 Gematech Innovation C Doc No 36 544 E 3 rev 02 Spare Parts List English Service Instructions Jede 1200E In this chapter E LU UU O CU C U LU Spare parts list Door Spare parts list Carousel Spare parts list Chassis Spare parts list Motor bracket 1 Spare parts list Motor bracket 2 Spare parts list Water tank Spare parts list Electronik box Spare parts list Cup presenter Spare parts list Additive module Contents 10 12 14 16 18 20 Spare parts list Door Spare parts list Carousel Spare parts list Chassis Spare parts list Motor Bracket 1 Spare parts list Motor Bracket 2 Spare parts list Water Tank Spare parts list Co
11. that the different drinks end up in the right places when they are refilled Menus 40 41 These menus relate to the payment eguipment which may vary to suit customer reguirements Menu 43 The right language should be correctly set on the display Menus 45 48 These menus relate to the payment key if this option should be available and if so how it should be used Menu 72 See below Service Instructions Jede 1200E rev 02 Programming Programming when the machine is in use It should normally be possible for this programming to be carried out by the customer and at the customer s site Menus 11 12 and 13 These menus relate to the pricing of drinks and they may be adjusted as required Menu 44 Day to day handling of coin dispensers and money boxes for machines that do not serve free drinks Menu 72 It is important to check this menu if powder cartridges are used as extra supplements Each powder cartridge is labelled with the maximum number of doses that can be dispensed Make a note of this number by the machine and check it each time a new powder cartridge is fitted Otherwise there is a risk that no signal will be given when it needs to be changed or that the contents of the cartridge are not used as efficiently as possible Menus 80 89 Deal with statistics on usage CHAPTER 2 31 Programming Programming example Enter service code Here the service staff can enter the authorisation code B or C t
12. the wall socket and give it a test run 1 Inner door 2 PC board 3 Display Replacing the push button panel Before dismantling the push button panel the display must be removed See above A Take the plug out of the wall socket 1 Open the main door and the inner door 2 Undo the ribbon cable on the push button panel on the control card See wiring diagram 3 Undo the screws that holding the push button panel Push the panel out backwards inwards 5 Fit the new one in the same way and connect the ribbon cable 6 Close the inner door 7 Close the main door 8 Put the plug into the wall socket and give it a test run 1 Inner door 2 PC board 3 Push button panel Service Instructions Jede 1200E rev 02 CHAPTER 3 55 Assembly description Replacing the coin dispenser The coin dispenser is accessible when the front door is open A Take the plug out of the wall 1 Open the door Undo the cable from the coin dispenser Remove the coin dispenser Connect the new dispenser using the ribbon cable Close the door Aa U A W MN Put the plug into the wall socket and give it a test run Type MARS This type has three catches to hold the coin dispenser in place One on the left one on the right and one at the bottom CHAPTER 3 56 Service Instructions Jede 1200E rev 02 Assembly description Circuit board control system Intermediary module 1 In
13. 02 CHAPTER 2 21 Programming 3 Selecting a drink Description Display text Default Authori sation Comment Visibility 21 Button 1 Menus 21 to 38 handle the 18 ingredient keys Submenus Ingredient Key 1 handle settings for one ingredient key 1 Button 1 1 ABC BC Box group 0 number of boxgroups max 11 for the Compartment Group beverage is selected 0 Not In Use If set to CanVendor X the rest of the sub menus will not be visible since they are irrelevant when using the button for Can Vendor Disabling Can Vendor on menu 8 1 or enabling CV Two Button Mode on menu 8 6 changes this 2 Button 1 0 ABC ABC Sets the individual price for the product Price Values 00 00 99 99 Parameter is only editable if menu 11 Same Price For all is set to NO Only visible if sub menu 1 is not set to CanVendor X Menu 8 1 is set to YES 3 Button 1 0 ABC BC Specifies the outlet valve for the button s ingredient LEAN See above 4 Button 1 1 ABC BC Sets extra output options such as pump and or water ExtraOutput spoon Options vary depending on Valve setting Pump is not allowed when using cold water valve See above 5 Button 1 38 ABC BC Shows how long time the outlet valve is open t ValveTime This time limits the total time for the pump delay PumpStartDelay and the time pump PumpTime
14. 1 Value of inserted coins ABC Displays the value of inserted coins routed to the coin routed to the coin box box since last reset since last reset Menu 89 resets statistics CoinBox value 83 Total amount of ABC dispensed in cup beverages UServings 1 Acc In Cups Served ABC Displays total amount of dispensed in cup beverages Not editable 2 Resetable Servings ABC Displays number of dispensed in cup beverages since last reset of this value Menu 89 resets statistics Service Instructions Jede 1200E rev 02 CHAPTER 2 29 Programming Description Default Authori Comment Display text sation Visibility 3 Acc Cans Served ABC Displays total amount of dispensed Not editable 4 Res Cans Served ABC Displays the number of dispensed cans since last reset Menu 89 resets statistics 84 Total number of sold ABC items per button Servings per Button 1 18 Recipe X ABC Submenus 1 18 display total number of sold items per button Not editable 85 Number of prepared ABC beverages per ingredient key since last reset Res Serv per Btn 1 18 Sales per drink ABC Submenus 1 18 display number of prepared beverages Recipe X per button since last reset Menu 89 resets statistics 86 Number of free drinks BC Displays number of free drinks served served FreeDrinks served 87 Number of errors pe
15. 200E rev 02 CHAPTER 2 11 Loading table Loading table variations without additives Variation No a 2 3 4 5 Button Carousel position Compartment number No 1 2 1 2 3 1 2 3 4 4 5 3 4 10 11 11 1 2 3 Esp 1 2 3 Esp CHAPTER 2 12 Service Instructions Jede 1200E rev 02 Loading table Varianter av laddningsschema med additiv i dryckesknappen Variation No Button Carousel position Compartment number No Additiv2 2 Additiv 4 NE 1 Rm NE ME NE 1 I Il I I I II I I I II I I I II I I I II I I I II I I im ER 1 1 2 1 2 3 1 1 2 1 2 3 1 A 1 2 A 1 2 3 A 1 A 1 2 A 1 2 3X 1 B 1 2 AX 1 2 3 AX 1 AX 1 2 AX 1 2 3 A 1 A B 1 2 B 1 2 3 B 1 Esp 1 2 Esp 1 2 3 AX 2 1 2 BX 1 2 3 BX 2 1 2 Esp A 1 2 3 Esp 3 1 2 A B 1 2 3 A B 3 3 4 1 2 3 Esp A 4 1 2 Esp 1 2 3 Esp 4 CV1 CV CV1 CV1 CV CV1 CV2 CV2 CV2 CV2 CV2 CV2 5 3 4 4 5 5 5 6 4 5 11 6 5 6 6 7 6 7 6 7 12 7 7 8 7 8 8 13 8 8 9 8 9 9 14 9 9 10 9 10 10 15 10 10 11 10 11 11 16 11 11 E 11 17 CV3 CV3 CV3 CV3 CV3 CV3 18 CV4 CV4 CV4 CV4 CV4 CV4 Esp To make ESPRESSO less water is added A A A _ additi In the Operator s Manual there is a loading table for the ze current machine giving the right p
16. 43095 Fl kt 24VDC Fan 24VDC 1 lt gt 43838 2 Motorhylla komplett utbytes Motor unit complete exchange 1 Service Instructions Jede 1200E rev 02 CHAPTER 4 79 Motor bracket 2 Motorbrygga 2 15 30 15 13 29 28 42 43 40 45 33 34 Service Instructions Jede 1200E rev 02 CHAPTER4 80 Motor bracket 2 Motorbrygga 2 02 10 15 Pos No PartNo Ben mning Term Antal Oty 28 43105 F ste f r buntband Clip for tiestrap 2 29 43249 F ste f r karusellmotor Bracket carouselmotor 1 30 48622 Karusellmotor Carouselmotor 1 31 48970 3 F ste f r l sgaffel Bracket for photocell 1 32 49254 L sgaffel Photocell 1 33 43116 Skruv M6 x 6mm Screw M6 x 6mm 4 34 48926 Lagerring karusellaxel Bearing driveshaft 1 35 46441 Mutter M8 nyloc Nut M8 nyloc 1 36 49688 Bricka 8x 19x Imm Washer 8x 19x Imm 1 37 43237 Woodruffkil 4 x 13mm Woodruff 4 x 13mm 1 38 Se pos 43 See ref 43 39 Se pos 43 See ref 43 40 43439 Bricka 6 4 x 14x 1 5mm Washer 64x 14x 1 5mm 1 41 43438 Nylonbricka 6 4 x 14x 2mm Washer nylon 6 4 x 14x 2mm 1 42 43835 Kuggrem kevlar Toothed belt kevlar 1 43 48625 7 Kugghjul stort komplett Toothwheel big unit 1 44 id Se pos 45 See ref 45 45 36695 Muggmotor komlett Motor cupcarousel unit 1 46 43141 Passbult 6x 25mm
17. 74 G ngled nedre 1200E Hinge lower 1200E 1 4 36490 Hylsa Sleeve 1 Service Instructions Jede 1200E rev 02 CHAPTER4 77 Motor bracket 1 Motorbrygga 1 a A 50 22 F 18 19 LS X gt j a igs ZS 21 BEN 22 m ki CHAPTER4 78 Service Instructions Jede 1200E rev 02 Motor bracket 1 Motorbrygga 1 09 12 Pos No Part No Ben mning Term Antal Oty 1 48917 1 Motorbrygga Motor shelf 1 2 48679 Bussning med krage Bushing with collar 1 3 43239 Axel kompl inneh Pos 3 4 7 8 Shaft compl Unit cont ref 3 4 7 8 1 4 Se pos 3 See ref 3 3 47898 Bricka Spacer 1 6 49389 Ratt M8 x 20mm Knob M8 x 20mm 1 7 k Se pos 3 See ref 3 8 Se pos 3 See ref 3 9 43352 Konsoll dispemserarm komplett Bracket dispensing arm compl unit 1 11 43229 Axel 6 x 65mm Shaft 6 x 65mm 1 12 Se pos 9 See ref 9 13 5 Se pos 9 See ref 9 14 ii Se pos 9 See ref 9 15 47761 Skruv M5 x 10mm Screw M5 x 10mm 3 16 17 18 43370 Skruv 4 3 x 20mm Screw 4 3x 20mm 19 Se pos 3 See ref 3 20 Se pos 3 See ref 3 21 5 Se pos 3 See ref 3 22 i Se pos 3 See ref 3 23 48914 5 Dispenserarm Dispensing arm 1 24 36233 R r vattenutmatning Pipe wateroutlet 1 25 36233 R r vattenutmatning Pipe wateroutlet 1 26 43547 R rh llare utloppsr r Holder pipe 1 27 36065 1 Fl ktkanal Funnel for ventilator 1 lt gt
18. A Carousel 4 x Compartment Group 2 N 1 0 Compartment Group 7 4 2 u N l 1 1 Compartment Group 8 t x 1 V NO Z Compartment Group J mm m gt Service Instructions Jede 1200E rev 02 CHAPTER 2 37 C Doc No 36 544 E 2 rev 02 Gematech Innovation Repair Adjusting English Service Instructions Jede 1200E In this chapter U U U U U U U Test running Troubleshooting Assembly description Adjusting and resetting Wiring diagram Service Guarantee Technical data Contents 3 Testrunnin 3 3 3 3 Test running without coins Test running without heat or water To select test running Service mode To escape from test running 4 Troubleshooting 4 8 Troubleshooting using error codes Troubleshooting otherwise 10 Assembly description 10 11 Replacing the inlet valve Replacing the outlet valve and pump Replacing the temperature sensor Replacing the level sensor Replacing the overheating protection Replacing the display Replacing the push button panel Replacing the the coin dispenser Circuit board control system 19 Adjusting and Resetting 19 20 Resetting the overfill protection Resetting the overheating protection 21 Wiring diagram 25 Service 25 Guarantee 25 Technical data CHAPTER 3 42 Service Instructions Jede 1200E rev 02 Testrunning The machine can be test run in two ways Test running without coins T
19. Bolt 6x 25mm 1 47 j Se pos 45 See ref 45 48 36658 Motorf ste b garpres Motor Bracket carouselmotor 1 49 43220 Fj der karusellmotor Spring carouselmotor 1 50 36686 Fotocell Photocell 3 51 43107 F stplugg f r styrkort Pin for PC board 4 52 49050 2 Styrkort serveringsmodul SM PC board serving module SM 1 53 43084 Halleffektgivare Hall sensor 1 54 48858 Dragst ng Pivot shaft 1 55 43218 H llare f r Hall givare Bracket for Hall sensor 1 56 48985 F ste f r mikrostr mbrytare Bracket for microswitch 1 57 43360 Skruv M3 x 12mm Screw M3 x 12mm 2 58 43230 Saxpinne 1 6x 16mm Cotter pin 1 6x 16mm 1 59 43154 Dragmagnet Solenoid 1 60 48925 F ste f r dragmagnet Bracket for solenoid 1 a 43227 2 Clips f r fixering av motorhylla Clip for carousel base 1 62 43655 EMC absorbent EMC absorber 1 Service Instructions Jede 1200E rev 02 CHAPTER4 81 Water tank Vattentank Service Instructions Jede 1200E rev 02 CHAPTER 4 82 Water tank Vattentank 09 12 Pos No PartNo Ben mning Term Antal Oty 1 Z93957 Kl mma Clip 1 2 43751 Silikonslang 7 5mm x 0 7m Silicone hose 7 5mm x 0 7m 1 3 48713 Distans Spacer 1 4 35019 verhettningsskydd Overheat protection 1 5 35025 Isolering tank Insulation tank 1 6 43000 Flott r gr Floatswitch grey 1 7 46047 O ring silicon 13 6 x 2
20. If the total of both these times is less than the open time for the outlet valve the water will run by gravity for the remaining time Value 0 gives the general time see menu 50 Range of values 0 150 tenths of a second See above 6 Button 1 10 ABC BC Shows how long time after the water dosage has started PumpStartDelay that the pump starts Range of values 0 100 tenths of a second See above 7 Button 1 28 ABC BC Shows for how long time the pump runs PumpTime Range of values 0 100 tenths of a second See above CHAPTER 2 22 Service Instructions Jede 1200E rev 02 Programming Description Default Authori Comment Display text sation Change Visibility 8 Button 1 No ABC BC Shows if an additive eg milk powder is in the drink Additive Group 1 Additive cartridge in group 1 Alternatives No additive Additive active One button on the menu panel can only handle two of the additive groups If an additive is activated AdditiveGroupX will be shown where X can be A B C or D depending on which loading table is active A B Cand Dstand in this case for the class of additive groups in the loading table q v See above 9 Button 1 0 ABC BC Shows the dosage number of presses per portion Additive Dosages 1 Range of values 0 10 Value 1 One dosage of the additive is dispensed when button 1 is pressed if this button is connecte
21. LED complete unit 25 36478 Programerings switch kpl Programming switch complete unit 26 36487 Kontakt RJ45 Connection RJ 45 27 36488 Gratis switch Free vending switch 28 36481 D rr kpl neutral Door basic model complete unit Service Instructions Jede 1200E rev 02 CHAPTER 4 73 Carousel Bagarkarusell CHAPTER 4 74 i Wt Q m H KT JA Service Instructions Jede 1200E rev 02 Carousel Bagarkarusell 07 11 Antal Pos No PartNo Ben mning Term Oty 1 43591 B gardispenser komplett Cup splitter complete unit 11 36099 Bagar dispenser komplett 73 5 mm Cup splitter complete unit 73 5 mm 11 48583 4 Karusellplatta Carousel base 1 48686 Skruv PTK50x 16 Screw PTK 50 x 16 33 43581 B garkorg Cup basket 11 36091 B garkorg 73 5 mm Cup basket 73 5 mm 11 48965 Ring vre f r karusell Ring upper for carousel 1 6 48986 Ring inre f r karusell Ring inner for carousel 1 43839 Karusell komplett Carousel complete unit 1 36101 Karusell komplett 73 5 mm Carousel complete unit 73 5 mm 1 Service Instructions Jede 1200E rev 02 CHAPTER4 75 Chassis Chassi CHAPTER 4 76 Service Instructions Jede 1200E rev 02 Chassis Chassi 07 11 Pos No Part No Ben mning Term Antal Qty 1 36373 2 G ngled vre 1200E Hinge upper 1200E 1 2 36371 Gliddel g ngj rn 1200E Hinge slider 1200E 2 3 373
22. The lowest value is edited on Submenu 1 and the highest on Submenu 6 Submenu 7 shows the number of decimals possible on the display 1 First value of coin type BC C Sets the value of coin type 1 CoinValue 1 Values 00 00 99 99 2 Next value of coin type BC C Sets the value of coin type 2 CoinValue 2 Values 00 00 99 99 3 Next value of coin type BC C Sets the value of coin type 3 CoinValue 3 Values 00 00 99 99 4 Next value of coin type BC C Sets the value of coin type 4 CoinValue 4 Values 00 00 99 99 5 Next value of coin type 0 BC C Sets the value of coin type 5 CoinValue 5 Values 00 00 99 99 6 Highest value of coin type 0 BC C Sets the value of coin type 6 CoinValue 6 Values 00 00 99 99 7 Number of decimals 0 BC C Sets the number of decimals used when displaying credit NbrOfDecimals rest or price on the display CHAPTER 2 24 Service Instructions Jede 1200E rev 02 Description Display text Default Authori sation Visibility Programming Comment 43 Language display Swedish BC C Sets the preferred display language If language is set to DisplayLanguage other than Swedish German French English Finnish Danish Spanish or Czech the language displayed will be English 44 Cointube status BC Sub menus hold information about the number of coins Cointube status in the connected MDB chang
23. VU JEDE Service Instructions u i i j EI Wes ul English Delivery date Supplier Type label d U JEDE MARIESTAD SWEDEN TEL 0501 670 00 FAX 670 67 VOLTAGE 2 i CURRENT SERIAL NO POWER INPUT Menu panel FREQUENCY C oo 1 Display with instructions 2 Drink 3 LED for drink About the Service Instructions The Service Instructions are aimed at persons trained to use the product The Service Instructions is devided into 4 chapters Chapter 1 contains concept definitions and safety instructions Chapter 2 contains loading tables system overview and directions for programming Chapter 3 contains troubleshooting with repair instructions Chapter 4 contains spare parts lists As well as the Service Instructions there is an Operator s Manual that describes the functions and handling of the machine It also contains installation and maintenance instructions Symbols AN Warns ofactions that can lead to injury or an important reminder aD Instructions for the correct use of the machine to avoid disrupting the functioning of the machine Notes comments or useful tips Manufacturer JEDE AB Box 303 SE 542 23 MARIESTAD Sweden Tel 46 0 501 67000 Fax 46 0 501 67 067 www jede com General Service instructions Jede 1200E In this chapter LJ Important notes for your safety U Concept definitions Contents 5 Important notes for your safety 6 Co
24. always starts with a time delay after the outlet valve has been opened to avoid splashing Service Instructions Jede 1200E revo2 CHAPTER 1 7 C Doc No 36 544 E Trev 02 Gematech Innovation Control system English 2 Service Instructions Jede 1200E In this chapter LI Loading table LJ System overview LJ Programming Contents 3 Loading table 3 4 5 Buttons Loading table variations without additives I Loading table variations with additives in drinks button 7 System overview N N d NN N Subsystems Document overview Authorisation Custom programming Recipe programming System programming The machine s functional modes 8 Programming CHAPTER 2 10 KO M M 10 24 25 26 27 28 29 Programming mode Button functions in programming mode Menus End programming Changing parameters Displaying statistics Menu overview Menu summary Programming example Enter service code Menu 0 Programming example Common or individual prices Menu 11 Programming example Individual drink prices Menus 21 38 Programming example Change tubes status Menu 44 Programming example Changing the maximum number of doses in a drinks cartridge Menu 72 Programming example Programming an additive for a selected basic drink Menus 21 38 Service Instr
25. and canned beverages Sales Statistics 1 In Cup Acc Total ABC Displays total value of dispensed in cup beverages Not editable 2 In Cup Res Total ABC Displays value of dispensed in cup beverages since last reset of this value Menu 89 resets statistics 3 Cans Acc Total ABC Displays total value of dispensed cans Not editable 4 Cans Res Total ABC Displays the value of dispensed cans since last reset Menu 89 resets statistics 5 Nbr of TOKEN Vends ABC Displays the number of vends paid with a token Menu 89 resets statistics 6 Val of TOKEN Vends ABC Displays the value of all vends paid with token Menu 89 resets statistics 7 Nbr Cashless Vends ABC Displays the number of vends paid with an MDB key card Menu 89 resets statistics 8 Value Cashless Vends ABC Displays the value of vends paid with an MDB key card Menu 89 resets statistics 9 Value of Revalue ABC Displays the value that has been transferred revalued to MDB keys cards Menu 89 resets statistics 10 Coinvalue to Tubes ABC Displays the value of all coins inserted and routed to the tubes of an MDB changer Menu 89 resets statistics 11 Coinvalue to Cust ABC Displays the value of all coins returned to customers Menu 89 resets statistics 12 Autocleared Value ABC Displays the value of all credits erased after 90 seconds inactivity See menu 13 Menu 89 resets statistics 8
26. annot the latter are in the form of statistical information etc Statistical information and parameters that can be changed can be accessed by selecting the main menu and where relevant the submenu Applies to program version 12 01 02 Other versions may deviate from this description 3 Selecting a drink page 14 4 Payment page 16 5 Water system page 18 6 Loading table page 19 7 Compartment page 20 8 StatistiCS page 21 1 System Description Default Authori Comment Display text sation Visibility 0 Service code 0000 ABC The user can enter a password to change authority level Enter Password The authority level is always A when the configuration program is started The current level of authority is indicated on the first display row like A B or C 1 Machine type Jede BC The machine type is displayed JEDE1200 Machine Type 1200 Noteditable 2 Seriel number JEDEHC ABC BC Machine identification Asset Tag Displays the EVA DTS machine asset tag identifier Current character is marked by Use buttons 1 and 2 to move between the characters Pressing key 3 selects the marked character and the parameter is altered by using keys 1 and 2 and set using key 3 The white space character is displayed as space and may only be used to set the length of the asset tag i e terminate the ass
27. ards and outwards 5 Place the carousel on a level surface so that none of the cup dispensers are pushed up Replacing the inlet valve 1 Markings on the dispenser arm 6 Turn the water tap off before the machine 2 Cup dispenser 3 Dispenserarm 7 Remove the tank lid and place a bucket under the drain hose N Note The water may be hot 8 Loosen the clip on the drain hose and let the water run into the bucket 9 Loosen the inlet hose overflow hose and hose to thewater tank 10 Loosen the securing screws on the valve and replace the valve 3 11 Fix the clip to the drain hose and replace the tank lid Replacing the carousel 12 Replace the carousel Make sure the guide pin on the mounting plate fits into the hole in the carousel Q Check that no cup dispensers have been pushed up If any have pull them down while holding the cup stack Start with the nearest one and continue by turning the carousel manually anti u clockwise 13 Close the door 14 Turn on the pressure with the water tap and put the plug in H Afterwards check that there are no leaks Hose for ventilating the inlet valve Overflow hose between the top of the water tank and the inlet valve Hose to water tank Inlet valve Tank support Drain hose Clip SEE BR MM CHAPTER 3 50 Service Instructions Jede 1200E rev 02 Assembly description Replacing the outlet valve a
28. ated MDB key card used and key charging not per mitted Try another coin Check allowable coin denominations Compare coin mechanism with program setting Correct any errors by reprogramming or changing coin mechanism Replace the coin mechanism Activate MDB Programming menu 40 Remove key card or activate charging Program ming menu 45 The coins do not fall down into the coin dispenser No display text The coin box is full A foreign object or coin has got stuck in the coin tube Poor fit between the coin tube and coin dis penser There is no power The display is broken EEPROM in wrong position Empty the coin box Press the coin return button Check that the opening to the coin tube is directly above the inlet to the coin dispenser Check the fuse and wall Change it Check Machine leaking or flooding Level control in inlet valve malfunctioning Leak at heater element or float switch Inlet or outlet valve dripping Replace inlet valve See section Replacing the inlet valve Seek and cure cause of overfilling See error codes E10 E11 Check tank gasket and make sure nuts are tight Check hose connections and replace valve Too little water filling Water supply time wrongly programmed Too low water pressure Tank not filling up Low water level in tank Outlet valve blocked Hose constricted Check setting on main menus 21 28 submenus 6 7 and 8
29. ater filter check if the filter is blocked and if it is replace the cartridge Q Clean inlet valve filter LJ Measure voltage at valve outputs when purchasing a drink If voltage 20 to 25 V the inlet valve is defective and needs changing If the voltage is below 20 V see if the float switch is indicating low water 0 1 W If not replace switch otherwise circuit board LI See fault Machine leaking water CHAPTER 3 44 Service Instructions Jede 1200E rev 02 Troubleshooting Error Description Cause Remedy code E10 Maximum time for first U Float switch in tank has not given LJ Checkthatthe switch is correctly seated straight filling obstructed signal to interrupt flow of water and then measure its resistance in raised posi tion If resistance is below 3 MW the switch is defective and needs changing E11 Maximum level not U Float switch working but circuit LJ Reset level control check connections between reached within 3 serv board or inlet valve defective float switch circuit board and inlet valve Then ings measure voltage on inlet valve when purchasing drink If the voltage 24 V approx is not inter rupted when the float switch indicates high wa The overfill protection ter lever the circuit board is defective and needs has triggered The changing If the voltage is interrupted but water overfill protector can continues to flow in the inlet valve is defective be reset see sec
30. ch 230 VAC To heating element From 230 VAC connector 230 VAC lt a Temperature sensor Float switch 18 VAC From the Transformer Service Instructions Jede 1200E rev 02 Wiring diagram button i Buzzer Optional for 800E 500E Q J1 REN 43744 2 BM 3 Module 43749 2 TM 3 Module CHAPTER 3 63 Wiring diagram Evacuation fan Outlet valve Cold water valve Optional Inlet valve Pressure pump m 43749 2 TM 3 Module 43749 2 TM 3 Module CHAPTER 3 64 Dispenser motors Additive module Service Instructions Jede 1200E rev 02 Service Always state the machine type when ordering service This infor mation can be found on the type label To ensure continued problem free function of your machine you can sign a service and care agreement More information about this can be obtained from your local machine supplier Technical data Guarantee JEDE AB will accept responsibility for faults resulting from defects in the design materials or manufacture for a period of 2 years gua rantee period Faults must be reported to JEDE AB or its nearest retailer Parts confirmed faulty by JEDE AB during the guarantee period are replaced by supplying a new fault free or repaired part JEDE has no responsibility beyond supplying such replacements This guarantee does not apply in cases of careless handling of the machine and only on condition that the care instructions have been
31. d Default value is NO MDB Revalue 46 Multivending NO ABC C Enables disables the multivending feature UMultivending If set to YES any remaining credits will not be returned automatically after purchase Default value is NO 47 Escrow function NO ABC C Enables disables escrow function Escrow allowed If set to YES credits can be inserted and then returned by pressing returnbutton if the machine is eguipped with an MDB changegiver with sufficient change without buying a product i e functioning as a changer Default value is NO 48 MDB card discount 0 ABC BC Sets a discount for customer purchasing using an MDB MDB Card discount key card If discount is greater than the price of a product the key card will not be charged at all although a key or card with at least 0 01 is reguired 49 Token acceptance YES ABC C Enables diables token acceptance in validator Val TOKEN enabled Service Instructions Jede 1200E rev 02 CHAPTER 2 25 Programming 5 Water system Description Display text Default Authori sation Comment Visibility 50 Watersettings ABC Submenus handle default values regarding valve and Def Watersettings pumptime for all ingredient keys 1 Def ValveTime 38 ABC This menu sets the global ValveTime value and updates the ValveTime value on menus 21 38 6 ValveTime 21 38 7 PumpTime will be set
32. d to an additive Value 2 Two dosages of the additive are dispensed when button 1 is pressed Value 3 etc See above 10 Button 1 No ABC BC Shows if an additive eg sugar is in the powder cartridge Additive Group 2 Additive in group 2 Alternatives No additive Additive active One button on the menu panel can only handle two of the additive groups If an additive is activated AdditiveGroupX will be shown where X can be A B C or D depending on which loading table is active A B Cand Dstand in this case for the class of additive groups in the loading table q v See above 11 Button 1 0 ABC BC Shows the dosage number of presses per portion Additive Dosages 2 Range of values 0 10 Value 1 One dosage of the additive is dispensed when button 1 is pressed if this button is connected to an additive Value 2 Two dosages of the additive are dispensed when button 1 is pressed Value 3 etc See above 22 38 Applies to Button 2 18 1 11 See button 1 Service Instructions Jede 1200E rev 02 CHAPTER 2 23 Programming 4 Payment Menu 40 41 42 These menus are linked to the payment mechanism and can vary according to customer s wishes Menu 43 The right language should be set on the display Menu 44 Running handling of the coin mechanism and coin box for machines not having free dispensing Menu 45 48 The
33. detailed description of the standard loading table see section Loading table in the Service Manual Service Instructions Jede 1200E rev 02 CHAPTER 2 27 Programming 7 Compartment Menu 72 It is important to check this menu if cartridges are being used as an extra addition Each cartridge is marked with a maximum value for the number of doses which it can supply This figure should be noted down in the vicinity of the machine and checked every time a new cartridge is fitted There is a risk otherwise that no signal will be re ceived when replacement is necessary or that the cartridge s content will not be used as effective as it should be Description Display text Default Authori sation Visibility Change Comment 72 Number of cups in a cup stack number of dosages in a full drink cartridge Nbr cups dosages ABC Shows how many cups there are in a cup stack number of dosages there are in a full drink cartridge Range of values 0 500 Each submenu represents one stack drink cartridge 1 11 cup stacks in the carousel Each new drink cartridge contains a fixed number of dosages A list of recommended values is available from the retailer The value must correspond to the value that the machine s microprocessor knows for the drink If the values differ they must be adjusted 1 11 Number of cups in the cup 90 ABC A 90 cups in a ful
34. e 1200E rev 02 Concept definitions Compartment groups for cartridges As in the case for the cup stacks the four drink cartridges are alsow group is used when a cartridge is empty The machine does not use arranged into groups By using groups the next cartridge in the thenextcartridge in a group until the first one is registered as empty See the following example Additive Drink cartridges Number of additive groups 2 2 See the loading table No 7 9 4 See the loading table No 10 12 2 1 1 See the loading table No 13 15 1 1 1 1 See the loading table No 16 18 One button on the menu panel can only handle two of these additive groups 3 1 Feeding hopper 2 Partition 3 Cup The four cartridges have a common feeding hopper for the powder To avoid contamination taste or other rea son there is an partition wall in the middle of the hopper See further section Loading table chapter 2 Refrigerating element As an option the machine can also be fitted with a refrigerating element for cold drinks Internal machine for cold drinks As an further option the machine can be fitted with an internal machine for cold drinks called CanVender Water output All mixing of drinks takes place in the cup For drinks requiring froth such as cappuccino there is a high pressure pump in addition to the outlet valve The high pressure pump
35. e giver MDB change giver 40 1 needs to be set to YES A change giver needs to be connected There will be a slight delay as the machine initializes the change giver The text Wait will be replaced by the first handled coin type on success 1 First cointube status BC Si If an MDB changegiver is connected and menu 40 1 is set NbrOfCoins to YES menus 44 1 6 display reported value and number of coins in the change giver s inventory tubes If ingredient key 1 is pressed when a particular coin type is displayed the change giver will be ordered to dispense one coin of that type Not editable by other means than dispensing coins with ingredient key 1 or inserting coins Authority level gt A required to fill Authority level gt B required to dispense If Check Change Giver is displayed no change giver is detected If Check MDB Settings is displayed menu 40 1 needs to be set to YES If Not Allowed is displayed the password for authority level C needs to be entered under menu 0 2 Second cointube status BC See above NbrOfCoins 3 Third cointube status BC See above NbrOfCoins 4 Fourth cointube status BC See above NbrOfCoins 5 Fifth cointube status BC See above NbrOfCoins 6 Sixth cointube status BC See above NbrOfCoins 45 Possibility to revalue an NO ABC C Activates deactivates the possibility to revalue an MDB MDB key card key car
36. e user and functioning of the machine at risk The machine is only completely free from current if the mains plug is out or the mains switch is off The power point must be in a position where the plug can be easily removed if necessary Check that the power rating corresponds to the data on the type label and that the main circuit is earthed correctly according to the current standard We recommend that the main circuit is fitted with an earth fault breaker Before putting the plug into the socket check that the water connection has been carried out in accordance with the instructions the main tap is open and the tank has been filled with water The manufacturer declines all responsibility if the electrical connection is not carried out according to the operating instructions Further safety instructions can be found later on in the Service Instructions Service Instructions Jede 1200E revo2 CHAPTER 1 5 Concept definitions Drinking cups The machine has a cup carousel with cup stacks Each cup is pre filled by the supplier to contain exactly the right amount of ingredients of the highest quality The drink is made by adding just hot or cold see below water Preparing the drinks in the cups eliminates the risk of mixing flavours Once a drink has been selected and paid for if necessary the cup carousel rotates so the correct cup stack reaches the cup presenter A cup is released and filled with hot or cold water The cu
37. eased from the inlet valve and emptied A Check that the plug is out 1 Turn off the water supply with the water tap Turn on the pressure with the water tap before putting the plug into the 2 Open the door 3 Locate the overflow hose connection to the inlet valve left wall socket side Release the hose connection and empty all water out of the hose 4 Slacken the water connection somewhat in order to release Q Akerwardechecktforleaks the pressure Refit the hose and water connection 6 Close the door 7 Turn on the pressure with the water tap and put the plug into the wall socket 1 2 3 1 Hose for ventilating the inlet valve 2 Overflow hose between the inlet valve and the water tank 3 Hosetothe watertank 4 Inletvalve Tank support Service Instructions Jede 1200E rev 02 CHAPTER 3 59 Adjustment and resetting Resetting the overheating protection The overheating protection is threaded in the bottom of the watertank It can be seen if the service lid is demounted Remove the cup carousel as described in the section Replac i ing the inlet valve Take the plug out of the wall socket and wait for about 10 minutes Remember that the machine contains hot water and that the water tank and cover may be hot 1 Remove the cover from the water unit Use a screwdriver See figure 2 Release the screw holding the service
38. et tag string Length may be between 0 and 8 characters Available characters are digits capital letters and white space Authority level gt A is reguired to change CHAPTER 2 18 Service Instructions Jede 1200E rev 02 Description Display text Default Authori sation Visibility Programming Comment 3 Set default values NO BC C Sets all parameters except menu 51 and 52 to default Set defaults values Level C authority is needed to set defaults YES NO Note Consider carefully the effect of resetting the machine to the default setting All customised settings will be deleted For the effect of the default setting see the section Menu overview 5 Software version BC Submenus display software version information six SW Versions digits Not editable 1 BM Version BC Displays the version of the BM software 2 SM Version BC Displays the version of the SM software 3 TM Version BC Displays the version of the TM software 6 Screensaver ABC C With this menu it is possible for the user to specify the text which will be shown on the LCD screen in the Screensaver position in other words when the machine shows Welcome for 15 seconds The text appears for 15 seconds or the length of time needed for the whole text to scroll over the screen maximum 30 characters 8 CanVendor ABC Submenus handle settings regarding t
39. g Description Default Authori Comment Display text sation Visibility 60 Loading table selected 1 ABC BC Selects and loading table All values on menus 21 1 38 12 Loading Table except 21 38 3 Price will be set to predefined values for the selected loading table Values 1 18 Once a loading table has been selected the following happens U The loading table is copied to the parameter Loading table editable where it can be changed manually Manual changes only affect the parameter Loading table editable The standard loading table is unaffected Q The parameters for drinks buttons Button X take their values from the selected loading table 61 Loading table BC Each submenu represents one compartment editable carousel position The value shows to which group a Edit Loading Table compartment belongs Range of values 0 16 1 16 Compartment 0 BC BC 16 sub menus Comp Group Comp Once a loading table has been loaded into the working memory it can be edited This change does not affect the original in E PROM If you are not satisfied with the change you can reload the same loading table from menu 60 and any changes that have been made will be lost An edited table can thus NOT be saved Each submenu represents a compartment carousel position The parameter value shows to which group a compartment belongs For a more
40. ge must be changed for the number of dosages in the cartridge to correspond to the value that has been set This programming example can also be found in the Operator s Manual CHAPTER 2 36 Service Instructions Jede 1200E rev 02 Programming Programming an additive for a selected basic drink Only applies to machines fitted with drink cartridges Main menu 21 38 Ingredient Key Submenu Additive Group 1 8 Additive Dosages 1 9 Additive Group 2 10 Additive Dosages 2 11 Authorisation B Starting point The door has been opened and the programming button has been pressed The door can either be closed or remain open The authorisation code has been changed to B from menu 0 Example In this example we follow loading table 14 and set the values according to this Button Variation 14 Submenu according to the 9 10 loading table Comp Group 1 Comp Group 1 A Comp Group 1 B Comp Group 1 C Comp Group 1 A C Comp Group 1 A B Comp Group 1 B C CON DMN R UN M Comp Group 2 Comp Group 3 Comp Group 4 Comp Group 5 Comp Group 6 Comp Group 7 Comp Group 8 6 o 5 9 CoO W BR OG OOO O O O oo E E O lt S O Oo Doo Er SO O SO O oo O G BU Ex Om Oo G E O O O O O O oo O lt lt Compartment Group 4 I 7 N r in h I 8 Compartment Group 5 Drink cartridges 4 5 7 N E z ze lt i g Compartment Group 6 I
41. has no effect if 14 1 is not set to YES Default value is 2 meaning 2 wins per 100 servings not necessarily exactly every 50 serving but a total of 20 5 wins per 1000 servings on average Values 0 100 Authority gt A is needed to change 15 Handles coin types Coins To Block With an MDB change giver connected and enabled under menu 40 1 this menu handles the coin types the unit can accept Each coin type can be blocked YES or not NO The settings here will apply when the inventory tube coin levels are sufficient Authority gt B is needed to change If MDB Change Giver is not activated menu 40 1 set to NO Check MDB Settings will be displayed If an MDB change giver can not be detected Check Change Giver will be displayed There will be a slight delay as the machine initializes the change giver The text Wait will be replaced by the first handled coin type on success CHAPTER 2 20 Service Instructions Jede 1200E rev 02 Programming Description Default Authori Comment Display text sation Visibility 1 10 Block Coin Type C If set to YES the coin type of the sub menu will be blocked during normal operation Each sub menu handles one of the coin types the change giver accepts The coin type is displayed in fractions of the currency 0 10 means 10 cent for instance if the change giver is of type Euro TKN refer
42. he Jede Can CanVendorOption Vendor 1 Enable CanVendor NO ABC BC Enables disables a Jede Can Vendor If set to YES a Can Vendor must be installed in order to start the machine else error E30 will occur Buttons 8 9 17 and 18 are reserved and not configurable for can vendor as long as can vendor is enabled Keys 8 and 17 are free if menu 8 6 is set to YES 2 CanPrice 0000 ABC BC Sets the Can price Values 00 00 99 99 3 Disable Discount NO ABC Enables disables the over all discount menu 48 for Cans 4 Disable FreeSwitch NO ABC C Enables disables the effect of the free switch on the BM3 board for Cans 5 CV Target Temp 8 C ABC C Sets the preferred target temperature for the CanVendor C 6 CV Two Button Mode NO ABC C Merges splits CanVendor lines If set to YES CanVendor line 1 amp 2 and 384 from left to right are connected and form two CanVendor boxgroups Can Vends are made using two buttons so two additional ingredient keys becomes available 8 and 17 7 Disable CV TOKEN NO ABC If set to YES a can vendor product may not be paid for using a vend TOKEN Authority gt B is needed to change 9 Button beep YES ABC ABC Turns beep sound when a button is pressed on off Button Beep YES NO Service Instructions Jede 1200E rev 02 CHAPTER 2 19 Programming 2 Price Description Display text Default Au
43. he machine can be test run without inserting a coin All other functions remain unaffected There is a toggle switch on the circuit board on the door to switch to free dispensing U Open door U Turn switch to ON If the switch setting should include CanVendor products as well the meny 8 submenu Disable Free Switch must be set to NO Q Do not forget to reset the switch to OFF on concluding the test Q This method should only be used by trained staff 1 Toggle switch for free dispensing Test running without heat or water This can be one way of test running functions not utilising heat To escape from test running or water i LI Unplug from the mains The machine can be test run exactly as normal but the machine will neither heat up nor take in water U Shut the door LJ Replace the mains plug The water tank is not filled up under Test Run mode To select test running Service mode See the section The machine s functional modes in chapter 2 in thes manual LJ Unplug from the mains with the door closed U Open the door LJ Plug into the mains again without shutting the door Service Instructions Jede 1200E rev 02 CHAPTER 3 43 Troubleshooting Troubleshooting using error codes Cause Remedy Error code Description Machine out of order Timeout carousel No communication between the PC boards and or the display UI The carousel cannot find the r
44. ight position LI The carousel is stuck U BM out of order U The jumper in the TM is lost Check that it is screwed in correctly and that noth ing is stopping it moving Timeout cup presenter The presenter is stuck Locate the fault Overpower motors High power consumption by any of motor pump inlet or outlet valve Measure the resistance Dispensing failure Cups stick together do not dispense Red diode marks the stack when door is open Acknowledge with button 3 3 times stack Photocell does not register carousel The fault is not stored in the error memory cannot be displayed Cup in place There is a cup or other object where the cup should be Remove the cup Driptray full U Drain and clean the driptray LJ Check connections for good contact E08 Internal error processor U Internal error in the SM PC board LI Change the the PCB SM LI Too old EPROM together w new TM PCB E09 RS 485 error SM SM TM or display PCB broken Change by try E10 Maximum time for first I Water supply obstructed U Make sure water filling is reaching the machine E11 filling obstructed Maximum level not reached within 3 serv ings The overfill protector has not triggered U Inlet valve not opening U Water leaking from the tank temporary interruption to the mains water supply may be the cause of the fault LI If the machine is equipped with a w
45. l stack stack Cups Dos Comp 12 Number of dosages 180 ABC A If menu 60 is set to gt 6 submenus 12 15 handle additive 15 in the drink cartridge cartridge dosages 1 4 like above U Dos Cartridge 180 number of dosages in a full cartridge 73 Number of cups dosages ABC Submenus set the default values used when setting a dafault new or reloading the same loading table under menu Def Nbr cups dos 60 1 Number of cups in the cup 90 ABC A Sets default number of cups per stack ice If the machine is reset to Basic setting by means of default j i i Menu 3 the number of cups will be reset to this value Def cups stack for all 11 compartments on the carousel After basic setting Menu 72 must be checked 2 Number of dosagesinthe 180 ABC A Sets default number of dosages per additive cartridge drink cartridge Authority A is enough to change default e e m Def dosages cart If the machine is Reset by means of Menu 3 the i maximum number of doses is reset to this value for all four cartridges After resetting Menu 72 will thus need checking CHAPTER 2 28 Service Instructions Jede 1200E rev 02 Programming 8 Statistics Description Display text Default Authori sation Visibility Comment 80 In cup beverages and ABC Submenus display sales statistics for in cup beverages canned beverages
46. menu Cups dos Cartr 01 Service code B Initial position The door has been opened and the programming button has been pressed The door can either be closed or remain open The display shows main menu Enter Password no 0 Example In this example the empty drinks cartridge is on the far left of the row The machine will be re programmed from dosage value 130 to 150 Press button 1 increase until the menu 72 Nbr cups dosages is shown PROG B 72 Nbr cups dosages Press button 3 to accept the menu choice Go to submenu Cups dos Cartr 01 with button 1 PROG B 72 Nbr cups dosages Dos Cartridge 01 Press button 3 to accept and go to the parameter value 130 ZAH a for further cartridges Return to Main Menu 72 Nbr cups dosages using button 4 PROG B 72 Nbr cups dosages Dos Cartridge 01 im Increase the value to 150 with button 1 130 Press button 3 to accept dm PROG B 72 Nbr cups dosages Dos Cartridge 01 Ar Press button 3 to the return to submenu i e to be able to adjust or check the value 150 PROG B 72 Nbr cups dosages NUNE ENI To end and save changes Press button 6 to finish Z The change is now implemented and saved 130 dosages have now been changed to 150 dosages for the drinks cartridge in compartment no 1 on the row Eh You must be at the main menu when pushing button 6 Note The cartrid
47. menu when pushing button 6 This programming example can also be found in the Operator s Manual Service Instructions Jede 1200E rev 02 CHAPTER 2 33 Programming Programming example Individual drink prices This setting is only applicable if individual drink prices have been set from Menu 11 by answering NO to this menu option See the programming example Individual drink prices are set from this menu Main menu 21 38 Ingredient Key Submenu Price Menu 21 refers to drink no 1 according to the menu panel usually coffee Menu 22 refers to drink no 2 according to the menu panel etc Only the submenu Price is available without an authorisation code Other submenus require Authorisation Code B Initial position The door has been opened and the programming button pressed The door can either be closed or remain open The display shows main menu Enter Password no 0 Example Illustrates how to set the price of drink no 1 to 20 eurocent Prices for other drinks are set in the same way PROG de Press button 1 increase until menu Ingredient Key 1 21 Ingredient Key 1 2 de Press button 3 to accept the menu option Go to submenu Price using button 1 PROG A 21 Ingredient Key 1 d Price PROG A 3 dm Press button 3 to accept the menu choice and go to the parameter value Now the 21 Ingredie
48. mponent Support Spare parts list Cup presenter Spare parts list Additive module CHAPTER 4 70 Service Instructions Jede 1200E rev 02 Door Dorr CHAPTER 4 72 Service Instructions Jede 1200E rev 02 Door Dorr 07 11 Pos No PartNo Ben mning Term 1 44055 Mikrobrytare Microswitch 2 36473 Skyddsglas Display glass 3 36463 Display Display 4 36523 F ste display MSPM 3 01 Richco Fixation for display MSPM 3 01 Richo 5 36356 2 F stpl t display Attachment plate for display 6 43744 Kretskort BM3 PC board BM3 7 36524 F ste kretskort EHCBS 7 5 01 Richco Fixation for PC board EHCBS 7 5 01 Richo 8 48676 Lysr rsh llare Fluorecent tube holder 9 36702 Tryckknappspanel Pushbutton panel 10 36700 St d f r tryckknappspanel Support for pushbutton panel 11 36525 Skruv st d MRT TT M4x6 Screw for support MRT TT M4x6 12 43006 Reaktor L15 240V Coil L15 240V 13 37018 Lysr r 30W 840 895mm E83 43714 Fluorecent tube 30W 840 895mm E83 43714 14 48677 Lysrorshdilare Fluorecent tube holder 15 47222 Glimmt indare Starter 16 36372 Ovre g ngledsstyrning Upper hinge guide 17 36448 Medbringare Rocker arm 18 36393 L s Lock 19 36396 Spanjolett Rod latch 20 36416 F nster kpl Window Jede 1200 E complete unit 21 36531 Mellanpl t kpl med bild Cover with picture complete unit 22 36650 Ljusl da Light box 23 Rengj ringsdekal 24 36476 Summer och Iysdiod kpl Buzzer and
49. ncept definitions NN NN OD DD a CHAPTER 1 4 Drinking cups Compartments for cup stacks Compartment groups for cup stacks Separate drink cartridges Compartment groups for cartridges Refrigerating element Internal machine for cold drinks Water output Service Instructions Jede 1200E rev 02 Important notes for your safety These instructions and warnings have been provided to help you avoid misuse and unnecessary risks and should be read before the machine is installed and used Only use this product in the way that it is designed to be used All other use will risk injury to people and damage to the product Please study these instructions carefully before servicing the drinks machine This is essential for correct installation of the machine and a requirement for the terms of the guarantee to be valid Store these operating instructions in a suitable safe place Never use cleaning agents containing solvents These can cause damage to the machine and may give off toxic gases There is also a risk of fire and explosion The water tank in the machine contains hot water and can cause burns if touched The highest guality materials and care during production will not prevent wear to the inlet hose The hose must therefore be checked regularly Replacing it in time will prevent damage and injury from the water For safety reasons repairs must be carried out by a professional Repairs not carried out by a professional can put th
50. nd pump The pump and valve are fitted together as one unit to the water tank The function of the pump is to provide greater water flow to make froth for certain drinks Remove the cup carousel as described in the previous sec tion Replacing the inlet valve Take the plug out of the wall socket 1 Turn the water tap off before the machine 2 Remove the tank cover and place a bucket under the drain hose A Note The water may be hot 3 Loosen the clip from the drain hose and let the water run into the bucket 4 Remove the cover from the water unit Use a screwdriver 5 Cutthe tie holding the pump 6 Dismantle the hoses and cabling Q Label the cables so they can be put back in the right places 7 Pull the unit straight out 2 8 Replace the whole unit A complete valve unit is available as a spare part 9 Push the pump unit back into place and put on a new tie 10 Replace the cables and hoses 11 Replace the cover plate 4 12 Replace the clip on the drain hose 13 Close the door 5 14 Turn on the pressure with the water tap and put the plug back in SR Afterwards check that there are no leaks 1 Tank cover plate 2 Pump 3 Tie 4 Valve 5 Feeder hose to cup Afterwards check for leaks Service Instructions Jede 1200E rev 02 CHAPTER 3 51 Assembly description Replacing the temperature sensor The temperature sensor is fitted on a tube at the bot
51. ner door 2 PC board for the intermediary mo 2 dule master card 3 Display The figure shows the PC board with the inner door opened Serving module The PC board for the Serving module can be found under the motor bracket It can be accessed by 1 removing the carousel and drinks cartridges see previ ous section pulling out the cup presenter 3 pulling out the motor bracket and turning it upside down 1 PC board for the Serving module 2 Motor bracket turned upside down Service Instructions Jede 1200E rev 02 CHAPTER 3 57 Assembly description Tank module The PC board fortheTank module can be found atthe electronic cabinet It can be accessed by 1 removing the carousel and drinks cartridges see previous section 2 Undo the two screws holding the cover plate according to the picture 3 pulling out the cover plate 1 PC board for the Tank module 2 Electronic cabinet 3 Screws holding the cover plate 4 Cover plate CHAPTER 3 58 Service Instructions Jede 1200E rev 02 Adjustment and resetting Resetting the overflow protection The overflow protection consists of a hose between the top of the water tank and the inlet valve To even out the pressure the hose is vented If the tank becomes overfull the hose will fill with the water which is blocking the inlet valve To reset the protection the overflow hose must be rel
52. nt Key 1 display shows Price 00 00 d Increase the value with button 1 or reduce it with button 2 Accept the price shown PROG A 4 i 21 Ingredient Key 1 with button 3 bole a 00 20 5 hy Press button 4 to return to main menu Ingredient Key 1 again We can now continue to the next drink with button 1 etc or i PROG A a 21 Ingredient Key 1 To end and save changes z Press button 6 to finish 6 The change has now been implemented and saved It takes a few seconds for the data to be stored If the door is closed the buttons on the menu panel go back to being drink selection buttons If all drinks have been priced button 6 just needs to be pressed once to apply to all amp You must be at the main menu when pushing button 6 This programming example can also be found in the Operator s Manual CHAPTER 2 34 Service Instructions Jede 1200E rev 02 Programming Programming example Change tubes status Service code C change Main menu 44 Coin tube status Initial position The door has been opened and the programming button pressed The door can either be closed or remain open The display shows main menu Enter Password no 0 n H H I PROG C g 1 N Press button 1 to go to main menu Cointube status Accept with button 3 This CM s Hi n n 44
53. o access and configure the menus that require these authorisa tion levels The preset authorisation code for B is 9317 for Cis 1001 Main menu 0 Enter Password Initial position The door has been opened and the programming button presed The door can either be closed or remain open The display shows main menu Enter Password no 0 PROG A 1 dm Press button 3 to accept the menu choice Now the display shows 00 Eed 00 2 d Press preset code 1001 for authorisation C by increasing the parameter value with PROG A button 1 or decreasing it with button 2 Password Press button 3 to accept and go to the next group of numbers PROG A 3 ry When the last number has been entered press button 3 to accept z zA BASS ord S The code is now shown on the bottom line 1001 A To go to another menu PROG A 4 d Press button 4 to return to the menus The display shows Enter Password again EEE a 5 m Press button T to go to the menu reguiring the Service Code amp You have to be ina main menu to be able to use button 6 to conclude The LEDs next to the relevant programming buttons will show green during programming when in programming mode Note After ending configuration with button 6 the service code returns to A 0000 CHAPTER 2 32 Service Instructions Jede 1200E rev 02 Programming Prog
54. ons change their function Buttons 1 4 and buttons 6 are now used for programming The LED for the relevant button will light and show green when the button has a programming function n n Button 1 Increases the number on the display s E Button h he display fr u Decreases the number on the display S A Button3 Confirms that the number is OK m ia n Button 4 Returns one level up to the main menu If there is only one level deep you come directly to the main menu o i E i fr Button 6 Ends programming mode i i The remaining buttons on the menu panel have no function in this mode CHAPTER 2 16 Service Instructions Jede 1200E rev 02 Menus Statistical information and values that can be changed can be accessed by selecting the main menu and where relevant the submenu The main menu is shown on the display with the menu number and name The submenu is shown with the name preceded by Some menus require a service code to change the parameter value Selecting a main menu Use the buttons on the front of the machine to choose menus see previous page When the programming button is pressed you will first go to main menu Enter Password No 0 LI Use button 1 to increase the main menu number Q Use button 2 to decrease the main menu number Q Use button 3 to select the main menu number PROG A 0 Enter Password
55. ositions for the different B additive cup stacks on the carousel X extra dose of the additive CV Canvender additive group Service Instructions Jede 1200E rev 02 One button on the menu panel can only handle two of the additive groups CHAPTER 2 13 Loading table Variation No det 13 14 15 16 17 18 Button Carousel position Compartment number No Additiv2 1 1 Additiv 1 1 1 1 M WW ka Sa WG 1 1 2 1 2 3 1 1 2 1 2 3 1 A 1 2 A 1 2 3 A 1 A 1 2 A 1 2 3 A 1 B 1 2 B 1 2 3 B 1 B 1 2 B 1 2 3 B 1 C 1 2 C 1 2 3 C 1 C 1 2 C 1 2 3 C 2 1 2 A C 1 2 3 A C 2 3 4 4 5 3 1 2 A B 1 2 3 A B 3 5 6 6 7 4 1 2 B C 1 2 3 B C 4 7 CV1 CV1 CV1 CV1 CV1 CV1 CV2 CV2 CV2 CV2 CV2 CV2 5 3 4 4 5 5 8 8 i a ac i In the Operator s Manual there is a loading table for the _ additive current machine giving the right positions for the diffe D additive rent cup stacks on the carousel X extra dose of the additive CV Canvender 1 additive group Q One button on the menu panel can only handle two of the additive groups CHAPTER 2 14 Service Instructions Jede 1200E rev 02 Subsystem The system consists of the following subsystems LJ The control unit for the order module BM LJ Control unit for serving module SM LJ The control uni
56. p presenter rotates and the cup can be reached Compartments for cup stacks The carousel has space for 11 numbered compartments with cup stacks The cup stacks are positioned according to a load ing table which should always be available for the machine Compartment groups for cup stacks The 11 compartments with cup stacks can be connected together into groups with the software This option extends the period be fore a particular type of drink such as coffee needs to be filled up For example coffee can be found in group 1 compart ments 1 2 3 coffee with sugar in group 2 compartments 4 5 6 coffee with whitener in group 3 compartments 7 8 coffee with sugar and whitener in group 4 compart ments 9 10 and chocolate in group 5 compartment 11 By using groups the next compartment in the group is used when a compartment is empty The machine does not use the next compart ment in a group until the first compartment is registered as empty Separate drink cartridges additives As an option the machine can be fitted with a total of four drink car tridges which may be sugar milk powder or other as an option This allows drinks to be varied further eg with extra sugar or milk These drink cartridges are placed ina line to the right of the cup carousel CHAPTER 1 6 1 A 3 4 u k Cup carousel Water tank with insulation Cup presenter Space for refrigerating element Service Instructions Jed
57. plate on the tank cover is remo ved Remove the cup carousel as described in the section Replac ing the inlet valve A Check that the plug is out Remember that the machine contains hot water and that the water tank and cover may be hot 1 Remove the tank cover as described in previous section 2 Release the screw holding the service cover plate and remove it The water tank bottom will now be visible 3 Dismantle both the high voltage connections on the overhea ting protection 4 Undothe overheating protection from the bracket and replace 1 the unit 5 Replace in reverse order 6 Close the door and put the plug back in TEE z zk 2 1 Service cover plate 3 2 Bottom part of the water tank 3 Overheating protection 4 Reset button 3 CHAPTER 3 54 Service Instructions Jede 1200E rev 02 Assembly description Replacing the display The display is fixed to the inside of the door with two i screws AN Pull the plug out of the wall socket 1 Open the main door and the inner door TT 2 Undo the connection J 18 on the PC board for the intermediary module See wiring diagram LL 3 Release the display cover unscrew the display andreplace 4 Connect the new display to the control card with the ribbon cable Close the inner door 6 Close the main door 7 Putthe plug into
58. r ABC Submenus display number of errors per error type error type Errors 1 37 EXX ABC Submenus 1 37 display number of errors per error type Not editable 89 All resetable statistics NO BC If YES is selected all resetable statistics are cleared Reset All Statist All EVA DTS resetable fields will be reset as if an audit list 1 had occurred Authority gt B is needed to reset values 90 EVA DTS password NO C If YES is selected the password required for collecting Reset EVA DTS Pwd audit data using an EVA DTS audit data collector will be reset to 0000 The password will be set again the first time an audit data collector unit using a password other than 0000 collects audit data from the machine CHAPTER 2 30 Service Instructions Jede 1200E rev 02 Menu summary Things to consider before delivery Menu 60 The machine s EPROM contains all the loading variations set up for this machine currently 8 A loading table ensures that the right drink is dispensed when a button is pressed and that the drink has the right amount of powder and water No further programming is needed if the factory settings are kept If the loading table has been selected it is therefore important LJ that the correct menu stickers are in place with or without prices U that the correct drink cartridges are fitted LJ thata copy of the loading table is put up inside the machine or that this is safeguarded in some other way so
59. ramming example Common or individual prices In our example we have used menu 11 which sets whether we want acommon price for the drinks The common price is set under menu 12 Individual prices are set under menus 21 38 submenu Price Service code BorC Main menu 11 All same price Initial position The door is open and the programming button has been depressed The service code for Level B or above has been entered under menu 0 The door can either be closed or left open The display will show main menu Enter Password no 0 PROG B 11 AllSamePrice fr Press button 1 increase until All same price is shown k PROG B 11 AllSamePrice gt A Press button 3 to accept the menu choice Now the display shows either NO or NO YES Change to YES with button 1 or to NO with button 2 M gt PROG B 11 AllSamePrice i Press button 3 to accept YES 3 The choice is shown on the bottom line VE To go to another menu finish or save the change 4 Press button 4 to return to the menus The display shows All same price again re Be Ek Press button 6 to finish 5 0 The change is now implemented and stored It takes a few seconds for the data to be stored If the door is closed the buttons on the menu panel go back to being drink 7 selection buttons db You must be at the main
60. s to TOKEN and N A not available will be displayed on the sub menus following all handled coin types and TKN if applicable 16 Handles the coin types C With an MDB change giver connected and enabled the unit can accept under menu 40 1 this menu handles the coin types the On Low Change unit can accept Each coin type can be blocked YES or not NO The settings here will apply when there is not sufficient inventory tube coin level i e low change condition Authority gt B is needed to change If MDB Change Giver is not activated menu 40 1 set to NO Check MDB Settings will be displayed If an MDB change giver can not be detected Check Change Giver will be displayed There will be a slight delay as the machine initializes the change giver The text Wait will be replaced by the first handled coin type on success 1 10 Block Coin Type C If set to YES the coin type of the sub menu will be blocked when in low change condition currently less than 5 coins in at least one inventory tube Each sub menu handles one of the coin types the change giver accepts The coin type is displayed in fractions of the currency 0 10 means 10 cent for instance if the change giver is of type Euro TKN refers to TOKEN and N A not available will be displayed on the sub menus following all handled coin types and TKN if applicable Service Instructions Jede 1200E rev
61. se from Can LJ The CanVendor is faulty or not con Q Replace Check connecting Vendor nected properly U Menu 8 1 in wrong position LJ Check the setting E31 Time out CanVendor LJ CanVendor is not properly connected Q Check connection service U CanVendor is faulty LJ Replace the CanVendor E32 Motor overcurrent Can Faulty CanVendor Replace the CanVendor Vendor CHAPTER 3 46 Service Instructions Jede 1200E rev 02 Troubleshooting Error Description Cause Remedy code E33 Low orhigh temperature CanVendor has not reached the menu 8 4 Increase CV Target Temp CanVendor CV Target Temp 5 C Let the CanVendor compressor continue cooling the beverages E34 CanVendor reports il U The temperature sensor faulty Q Replace the temperature sensor logical temperature UI The CanVendor not properly initi Q Check the installation ated Compressor error Can CanVendor reports internal compressor Replace the CanVendor Vendor error Dispensation error on CanVendor reports dispensation error Check the CanVendor for stuck cans or bent dis CanVendor pensers Service Instructions Jede 1200E rev 02 CHAPTER 3 47 Troubleshooting Troubleshooting otherwise Cause Remedy The coin dispenser is not accepting coins Defective coin Incorrect coin denomination Mismatch between coin mechanism and coun try in system program The coin mechanism defective MDB not activ
62. se menus deal with the payment key If the facility is to be present and if so how it is to be used Description Display text Default Authori sation Comment Visibility 40 MDB ICP NO ABC C Activates deactivates support for MDB Multi Drop Bus MDB ICP units units When enabling MDB if menu 12 is 0 menu 11 is set to YES and menu 12 is set to 1 00 0 25 if menu 41 CoinTable is set to Great Britain 1 Change Giver NO ABC C If set to YES a MDB change giver has to be connected at startup otherwise error E25 occurs 2 Key Card Reader NO ABG C If set to YES a MDB key card reader has to be connected at startup otherwise error E27 occurs 41 Preferred cointable Sweden ABC C Sets the preferred cointable Cointable Normally this is done automatically when a MDB unit identifies itself Values Swedish User Defined Country Country Country Country Country Country France 2 France Hungary Turkey Greece Sweden Ireland Cyprus Iceland Germany Portugal Germany 2 Finland Norway Poland Spain Slovenia USA The Netherlands Czech Great Britain 2 Austria Great Britain Belgium Denmark Euro Switzerland Token Russia User defined 42 Cointable setup BC C If menu 41 is set to User Defined the cointable can be Cointable setup edited the submenus Used if the parameter Coin table is set to User defined
63. t for the tank module TM See also the section Circuit board control system in chapter 3 Document overview These Service Instructions describe all the parameters that can be programmed displayed and the commands that can be executed The Operator s Manual describes the programming that can be carried out by the user himself herself without calling on the service staff Authorisation The system has three authorisation levels A Band C linked to the type of programming UI Customer programming authorisation level A Described in the Operator s Manual LJ Recipe programming authorisation level B LJ System programming authorisation level C There is a separate access code for each authorisation level For authorisation level A the service code is preset to 0000 and does not need to be entered Configuration at this authority level is carried out by the user Service codes B and C are also preset and are given in the delivery documentation Staff who will handle recipes and systems ie authorisation levels B and C enter these codes from menu Enter Password No 0 This opens the menus that reguire these codes See below and also the programming examples later on in these instructions Authorisation level B covers level A and authorisation level C covers level B Customer programming Authorisation A also allows some non editable statistics to be dis played such as total sales value value in coin box
64. thori sation Visibility Comment 11 Same price for all All same price YES ABC BC Sets the same price for all in cup products condition If set to YES the price set in menu 12 applies Authority gt A is needed to change 12 Common price for all Price for all ABC BC Sets the common price for all in cup products The price only applies if menu 11 is set to YES Authority gt A is needed to change 13 Autoclearing of credits Autoclear credit NO ABC BC Engages disengages the autoclearing of credits NO If previous user have overpaid the available balance can be used by next user with no time limit YES Any available balance disappears after 90 seconds The sum of erased balance can be seen in the statistics in menu 80 submenu Autoclear Value Authority gt A is needed to change 14 Jackpot Jackpot Settings ABC Submenus set parameters regarding the winning function Enable Jackpot NO ABC BC Enables disables the jackpot function If set to YES in cup products can be won If the product costs gt 0 and the customer is lucky credits will remain after purchase and the display and LEDs will indicate that the beverage was won Only in cup products can be won Authority gt A is needed to change Wins per 100 drinks 002 ABC BC Wins per 100 drinks sets the average win percentage It
65. tically go to the relevant parameter The parameter is displayed on the left If the parameter consists of more than one number it can sometimes be changed in groups U Use button 1 to increase the value LJ Use button 2 to decrease the value LJ Use button 3 to edit the next group or to finish if the last group has been edited A parameter value that can be changed will flash when it is shown Displaying statistics The microprocessor gradually stores data that can be used as statistical information Statistics that can be displayed are total sales value value in coin box total sales per drink f the machine contains a coin dispenser total number of servings total number of errors per error code number of free drinks number of servings payed with token number of servings payed with MDB Card value of servings payed with token or MDB Card value filled to the MDB Card value to the tubes if the machine contains a coin dispenser value to the box and if the machine has erased the balanced credit after 90 sec the value can be seen under menu 80 NB Menus 80 1 83 1 and 84 1 18 will not be deleted when a new upgraded software is discovered on start up and the EPROM is erased CHAPTER 2 17 Programming Menu overview The programming of the machine is based on a number of menus The display on the front of the machine has four rows each with 20 possible characters Some parameters can be changed and some c
66. tion and needs changing Resetting the overfill protector E12 Overpower exits High power consumption by any of Measure the resistance pump inlet or outlet valve E13 Low temperature Ifthe temperature fails to rise LJ Check mains cable and fuse Temperature in water U No current reaching machine tank below 50 C LI Reset as per description in section Resetting LJ Overheating protection triggered the overheating protector U Change the temperature sensor U Temperature sensor not working LI Change the heater element U Heater element faulty E14 Ilogical temperature LJ Temperature wrongly set or tem U Change the temperature sensor can not be Temperature recorded perature sensor faulty adjusted in water tank below 1 C or above 110 C LI Too little water in tank LJ See E10 E11 E15 Internal fault in micro Computer fault in tank module Change the PC board by try processor E16 RS 485 fault LJ SM TM card or display PCB broken Q Change by try LI The jumper is not in the correct L Adjust position E17 Fault on push button LJ Fault in connections to from control Q Checking wiring panel panel LJ Wires to control card not connected Check and plug in poss loose contact no buttons working LJ Fault on control card no buttons U Change the PCB working LJ One or more buttons malfunction LI Change the push button panel ing E18 MDB ICP error no MDB error in the change giver key Check and change the broken device
67. to Def ValveTime minus Def PumpStartDelay The value is used when a new loadingtable is selected under menu 60 even if the value in the loadingtable selected differs 2 Def PumpStartDelay 10 ABC Works like menu 50 1 but handles the PumpStartDelay value 3 Water TestMode ABC Used for anormal water dose for testing The tank module must be in stand by mode Press button 1 to start a water dose with the same settings as for drinks button 1 Press button 2 to end a water dose that has been started 51 Target temperature 80 C ABC Sets the preferred target temperature C for the tank Water Temperature module TM Range of values 75 90 CHAPTER 2 26 Service Instructions Jede 1200E rev 02 Programming 6 Loading table Menu 60 The machine s EPROM contains all loading possibilities available on that machine A loading table ensures that the right drink emerges when a button is depressed and that the drink correctly consists of powder and water No further pro gramming is necessary if the factory set values are accepted If the loading table has been chosen it is thus important U that the right stickers are in place with or without prices U that the right cup and any cartridges have been installed U that a copy of the loading table has been set up inside the machine or that this has been assured by other means so that the different drinks are in the right place during refillin
68. tom of the tank It is easier to do this operatin if the tank will be demounted and leaned For that reason the tank must first be emptied Remove the cup carousel as described in the previous section Replacing the inlet valve AN Take the plug out of the wall socket 1 Turn the water tap off before the machine 2 Remove the tank cover and place a bucket under the drain hose 3 Undothe clip on the drain hose and let the water run into the bucket A Note The water may be hot 4 Remove the tank cover as described in the previous sec tion 5 Undo the screws holding the protection cover over the electric cabinet and take it out 6 Undo the screws holding the water tank unit and take it out 7 Pullthe sensor from the tank straight down 8 Remove the cable connection J 5 on the control card for the tank module The cable is blue white black 9 Replace in reverse order 10 Close the door open the water tap and put the plug back in 1 Temperature sensor Blue white black cable for the tempe rature sensor Electric cabinet Fastening screws Protection cover Control card for the Tank module N ANAM CHAPTER 3 52 The tank module with removed cover over the electrical cabinet Service Instructions Jede 1200E rev 02 Replacing the level sensor St St SB N Control card for the Tank module Electric cabinet Fastening scre
69. uctions Jede 1200E rev 02 A loading table specifies the compartment in which a cup stack should be placed and how the machine s 11 compart ments can be arranged into groups by means of the software The machine s EEPROM contains a number of different loading table variations The machine is delivered with one ofthe loading Itisvery important that the selected loading table is followed when loading drinks cartridges Otherwise the drinks menu on the front of the machine will not be correct Loading table tables loaded in the working memory This loading table can easily be changed for one of the others according to the list below The variations can also be modified according to individual reguire ments For more information see section Menu summary menus 60 and 61 Buttons Button no 1 Button no 10 Button no 2 Button no 11 Button no 3 Button no 12 Button no 4 Button no 13 Button no 5 Button no 14 Button no 6 Button no 15 Button no 7 Button no 16 Button no 8 Button no 17 Buttonno 9 Button no 18 Loading table no Compartment in cup carousel in the Operator s Group no Manual there is a loading table for the current machine giv ing the right positions for the different cup stacks on the carousel Service Instructions Jede 1
70. ws Protection cover Level sensor Securing nut for the level sensor Service Instructions Jede 1200E rev 02 Assembly description Remove the cup carousel as described in the section Replac ing the inlet valve A Take the plug out of the wall socket 1 N Turn the water tap off before the machine Remove the tank cover and place a bucket under the drain hose AN Note The water may be hot a U1 JS Ww N co sch 0 0 11 Undo the clip on the drain hose and let the water run into the bucket Undo the screws holding the protection cover over the elec tric cabinet and take it out Undo the cable JA on the conntrol card for the tank service module See wiring diagram TM module Undo the nut on the outside and remove the faulty sensor Remove the old joint as well Fit the new level sensor with a new joint Do not over tighten the nut so the thread is damaged but tight enough for the level sensor to make a seal to the water tank Cut the new cables to a suitable length Peel back the ends and fit to connection J 4 on the control card Reassemble in reverse order Close the door Turn on the pressure with the water tap and put in the plug Afterwards check that there are no leaks CHAPTER 3 53 Assembly description Replacing the overheating protection The overheating protection is threaded into the tank bottom It can be reached if the service cover
71. y first start up so called initial start up certain data is initiated and written back to E PROM It takes longer to write to than to read from E PROM and the display is therefore turned off for longer than at other start ups When start up is complete the machine is ready for opera tion Drink selection starts when a button is pressed If no button is pressed within 10 seconds drink selection ends Payment starts when a coin is inserted into the coin dispenser The balance is shown on the display If a drink has been selected but the balance is too low payment starts after the drink has been selected The display shows the amount due If no coin is inserted for 10 seconds drink selection ends Service mode To set U Take the plug out of the wall socket with the door closed U Open the door LJ Put the plug back into the wall socket In this mode the machine function can be run without activating the water function filling and heating up the water see e g the section Test running further on in the manual chapter 3 Programming mode See next page CHAPTER 2 15 Programming Programming mode To set Open the door when the machine is in operating mode and press the program ming button inside the door The door can now be closed or remain open Button functions in programming mode 1 Network socket 2 Programming button When the programming button has been depressed the menu panel butt

Service Instructions Jede 1200E

Contents

Download Pdf Manuals

Related Search

Related Contents