Field Manual 02/06
Contents
1. EXTERIOR PAINTED ALUMINUM SURFACES 10 YEARS Woodgrain Millwork warrants that the paint on the exterior of aluminum clad products will not under normal atmospheric conditions peel check crack or flake for a period of 10 YEARS from the date of manufacture The paint performance will vary depending on installation in heavy salt spray environments elevation orientation altitude and other atmospheric conditions Paint surfaces will weather over time To prolong the life and appearance of the paint coating it is recommended that exterior cladding be cleaned any time the exterior glass is cleaned See your Woodgrain Millwork distributor for a copy of the maintenance and cleaning instructions or refer to AAMA 610 1 79 If a paint failure should occur Woodgrain Millwork reserves the right to determine the best method for corrective action HARDWARE AND ALL OTHER COMPONENTS 1 YEAR Woodgrain Millwork Field SVC Manual 12 05 Woodgrain Millwork warrants that hardware and other components shall be free from defects under normal conditions for a period of 1 YEAR from the date of manufacture Woodgrain Millwork will provide replacement parts free of charge during the warranty period Since we purchase many of these items from other manufacturers we cannot guarantee that the exact model or design of hardware will be available in the future and usually the then current model will be provided Any components or product repaired or replaced are2. A woodgrain millwork Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Release Agreement Inspection form Warranty Replacing swing panel Replacing sliding panel Adjusting standard hinges Adjusting adjustable hinges Replacing a profrench astragal Replacing a design french astragal Replacing a center swing astragal Replacing a sweep Replacing glass Replacing ACL bars Replacing a sill cover Replace weatherstrip channel at slider Replacing a keyed cylinder on a swing door Replacing a keyed cylinder on a sliding door Replace handleset on a swing door Replace handleset on a sliding door Replace interlock weatherstripping Replacing a multipoint lock Swing Adjusting multipoint lock Sidelite Adjusting rollers Adjust Sliding lock Caution Panels glass etc can be quite heavy Always lift appropriately Follow manufacturers instructions for safe use of hand and power tools Pg 2 Pg 5 Pg 6 Pg 8 Pg 12 Pg 13 Pg 14 Pg 15 Pg 16 Pg 17 Pg 18 Pg 19 Pg 20 Pg 21 Pg 22 Pg 23 Pg 24 Pg 25 Pg 26 Pg 27 Pg 28 Pg 29 Pg 30 Pg 31 Pg 32 Woodgrain Millwork Field SVC Manual 12 05 A woodorain millwork THIS SERVICES AGREEMENT this Agreement is made and entered into by and between WOODGRAIN MILLWORK INC an Oregon corporation Woodgrain and the repair and service technician identified below Contractor The purpose of this Agreement is to provide the t
3. Contract Documents For this purposes losses shall mean any damages losses deficiencies actions suits fines penalties proceedings judgments costs or expenses including reasonable attorneys fees Contractor s indemnity obligations shall survive termination of this Agreement 9 CHANGE ORDERS Changes in the services required under any Work order are within the general scope of this Agreement and may be accomplished by Change Order without invalidating this Agreement A Change Order is a written agreement issued after execution of this Agreement and the issuance of a Work Order by Woodgrain and signed by Woodgrain and Contractor stating their agreement upon a change and adjustment in the Work Order and or in ihe rates set forth in Exhibit A 10 RESTRICTION ON TRANSFER This Agreement and the other Contract Documents are personal to Contractor Contractor shall not sub contract delegate assign or otherwise transfer any interest in or obligations under this Agreement without the prior written consent of Woodgrain which may be withheld in Woodgrain s sole discretion 11 RELATIONSHIP OF PARTIES Woodgrain and Contractor agree that Contractor is an independent contractor and under no circumstance shall the Contract Documents or the relationship between the parties be construed as creating a joint venture partnership agency or an employer employee relationship 12 TERM This Agreement will commence on the dale he
4. Do latch bolts bind with strikes if so where CJC Was handleset installed so tight that it effects locks operation Woodgrain Millwork Field SVC Manual 12 05 IN _ woodgrain millwork ATRIUM PATIO DOOR WARRANTY The Limited Warranty protection provided here under shall extend only to the first retail purchaser and or original homeowner LIMITED WARRANT Y Woodgrain Millwork warrants subject to the conditions and restrictions stated below that its products and components thereof shall be free from defects in materials and workmanship at the time of shipment from our mill in Greenville Texas for a period of one 1 year from date of purchase provided the Atrium Door unit was strictly maintained stored finished and installed in accordance with Woodgrain Millwork s written instructions that accompany each product INSULATED GLASS 20 YEARS Woodgrain Millwork warrants the insulated glass in our patio doors shall be free from manufacturing defects for a period of 20 YEARS from the date of manufacture Our insulated glass is warranted not to develop under normal conditions any material obstruction of vision as a result of manufacturing defects or a premature failure of the edge seal This limited warranty does not apply to special glazings and glass not factory installed by Woodgrain Millwork If any repair or replacement is necessary such repair or replacement is warranted for the remainder of the applicable warranty period
5. Install one screw in the center hinge 7 Install one screw in remaining hinges 8 Install all remaining screws 9 Install hardware 10 Adjust hinges Caution When installing screws do not over tighten Woodgrain Millwork Field SVC Manual 12 05 12 Replace sliding panel 1 Assure new panel matches the size and handing of the existing panel 2 Slide panel open 3 Remove phillips head screws from head stop Head stop must be removed 4 Slide panel closed 5 Latch panel into strike 6 Remove remaining phillips head screws from head stop 7 Unlatch tilt panel into room and remove DO NOT SET PANEL ON ITS BOTTOM RAIL 8 Transfer hardware and any weatherstripping to new panel 9 Set new panel into opening and latch into the strike 10 Follow steps 2 thru 6 in reverse to install head stop 11 Adjust door height lock and latch Woodgrain Millwork Field SVC Manual 12 05 13 Adjusting standard hinges To tighten reveal 1 Remove hinge pin of the hinge that needs adjustment Further adjustment of adjacent hinges may be required 2 Tape the jaws on a 6 or 8 crescent wrench 3 Bend the barrels that are attached to the panel towards the panel A minimal amount 1 16 is too much Too much causes the hinges to bind 4 Reinsert the hinge pin 5 Close panel and check the reveal To increase the reveal 1 Remove the two screws closest to the barrel 2 Loosen the remaining sc
6. ample pressure to snap sill cover into place Woodgrain Millwork Field SVC Manual 12 05 22 Replace bottom rail weatherstripping on an active slider Remove operable panel Rest panel on its side stile Remove existing screws Remove weather stripping Clean any tape residue off of the panel Remove protective tape from adhesive tape on new weathestripping Apply new weather strip to panel Insert existing screws thru channel into the panel Reinstall panel Woodgrain Millwork Field SVC Manual 12 05 23 Replacing a keyed cylinder on a swing door 1 Remove allen set screw on the exterior lever 2 Remove interior escutcheon plate screws 3 Remove exterior escutcheon plate 4 From back side of the handleset Remove bracket that holds the keyed cylinder in place 5 Remove keyed cylinder 6 Repeat steps 1 thru 5 in reverse to reassemble Woodgrain Millwork Field SVC Manual 12 05 24 Replacing a keyed cylinder on a sliding door 1 Remove interior escutcheon plate screws Hold escutcheon plate in place while removing screws 2 Remove exterior escutcheon plate 3 From back side of the handleset Remove bracket that holds the keyed cylinder in place 4 Remove keyed cylinder Repeat steps 1 thru 5 in reverse to reassemble Woodgrain Millwork Field SVC Manual 12 05 23 Replace swing handleset 1 Remove allen set screw on the exterior lever 2 Remove interior escutcheon plate screws 3 Remove handleset 4 Repeat
7. and sides of panels painted stained JL Ts ext perimeter of glass cap beaded Grilles ACL OC are egrilles ACL correct width OToo narrow OWrg Sz are grilles ACL correct height OToo shot O Wrg Sz LOCIDo ACL bars line up with internal mill bars DODo ACL bars line up with other panels in unit I Were shims placed behind hinges and every location where long LOCDAre ACL bars level screws were placed thru the frame into the wall studs Seal Failure i_JOn units where panels were hinged off of the jambs that butt azai OOs moisture between the insulated glass the wall were 2 1 2 screws used at screw location of each hinge _ JDoes water show in the interior at the bottom of the glass I Are wicking pads installed on swing units Lis moisture on interior glass surface Hardware C Is lever hard to move LOC Does lever return to position 4 Does air water come in below the sill because there is no sealant DOCODoes multipoint mechanism move Does air come in at sliding door interlock lt ls swing sliding APS door sweep intact Are jamb weather strips in place E ils sliding panel adjusted up ls sliding door sill interlock neoprene block in place w JIs sliding door sill interlock wicking pad in place Unfinished Parts required to solve situation Quantity and Specifics Name of Representative JC Does lock engage head and sill Does slider lock engage jamb strike COC
8. color variations and other wood characteristics within Woodgrain Millwork s specifications 6 Natural warping of wood components unless the warp exceeds 1 4 warp includes bow cup and twist Normal weathering or wear and tear Swinging doors over 7 ft tall without factory installed multi point locking hardware Any special product or item which manufactured according to specifications provided by the customer cn B o ub ues Woodgrain Millwork Field SVC Manual 12 05 10 Any product in a size which is greater than that shown in our catalog these products are purchased as is without warranty 11 Product purchased without factory installed glazing these products are purchased as is without any warranty 12 Problems due to improper maintenance installation or application 13 Any product installed in structures that do not allow for proper drainage such as Exterior Insulation Finish Systems EIFS 14 Any consequential incidental special or punitive damages 15 Products manufactured by others 16 Corrosion tarnishing or operation of standard hardware in high salt spray environment 17 Damage caused by or adjustment required as the result of a Improper handling installation or maintenance and or during delivery by others b Exposure to conditions beyond performance specifications and or design limitations c Water infiltration other than as a result of manufacturing defects d Condensation e Glass damage caused by
9. or its business to any customer The confidentialily obligations of this Section 15 shall survive termination of this Agreement 16 APPLICABLE LAW This Agreement shall be governed and controlled by the laws of the State of Idaho without regard to its conflicts of laws principles 17 EXECUTION This Agreement and the other Contract Documents may be executed in one or more counterparts each of which shall be deemed an original and all of which together shall constitute one and the same instrument Any counterpart may be delivered by facsimile transmission WOODGRAIN MILLWORK INC By Title Address for Notice Print or Type Name of Contractor Signature Title if applicable Address for Notice EXHIBIT A SCHEDULE FOR LABOR RATES 1 Labor Rates The hourly labor rate s charged by Contractor to Woodgrain shall be as follows Hourly travel rate Hourly on site rate technician Hourly on site rate technician s helper 2 Mileage Rate 3 per mile 3 Additional Charges Provisions Contact Information Billing Address City State Zip Shipping Address Cit State Zip Business Phone Mobile Phone Woodgrain Millwork Field SVC Manual 12 05 A woodgrain millwork RELEASE AGREEMENT This Release Agreement Agreement is entered into between Complainants and Woodgrain Millwork Ine Woodgrain Millwork on the date specified below RECIT
10. others i e brickwash sanding or improper cleaning washing f Damage to metal or other surfaces by brickwash chemicals or airborne pollutants g Catastrophic weather or acts of God including fire wind or wind blown objects LIMITS OF LIABILITY This warranty is in lieu of all warranties express or implied including any implied warranties of merchantability or fitness for a particular purpose No distributor dealer employee salesperson or representative of Woodgrain Millwork has any authority to modify this warranty in any way Woodgrain Millwork is not liable for any consequential incidental special or punitive damages costs of installation of replacements or costs of refinishing of door components or adjacent parts millwork Final determination of whether or not a defect exists shall be made by Woodgrain Millwork Woodgrain Millwork at its sole discretion may repair or replace the defective part or product or refund the original purchase price We reserve the right to perform the warranty work or arrange for another party to perform the warranty work This warranty is only applicable in the USA and the District of Columbia This warranty Is governed by the State of Texas without regard to choice of law principles CLAIMS PROCEDURE If you have any questions regarding this warranty or have any claim under the provisions of this warranty please contact Woodgrain Millwork at its Manufacturing facility listed below C
11. posts Is unit square Jl als lock margin constant 1 8 Is hinge margin constant 1 8 L Are jambs header jamb bowed CO IN CJ OUT lt JLZIf ves were shims or long screws used to correct the bow f Is measurement from sill to head jamb the same at hinge and lock location If no give exact measurement at LOCK HINGE 7 3C 3Is head and sill the same length If no give exact measurement at HEAD SILL Is hinge stile at fixed panel plumb i Where does operating door hit or bind Clock jamb Clhead jamb Ohitting at lock Clpanel Khinge bind Cthreshold Olwicking pads Llastragal Ciweather strip 4 Does slider lock rail have an even vertical reveal with door jamb J Does slider lock easily i Does the slider panel move when locked Ticket Number Y N Warp OO Was 60 straight edge or taught string used to determine arp If no What was used CC Does panel bow at OTOP BOTTOM Olis unit plumb Check all jambs and mull posts CC Are the face of hinges flush w surface of stile edges CC Are the fixed and operating panels flush at hinge stiles Operating Panel width TOP MDL BTM LOC Is exterior Unfinished properly painted OO ls exterior Unfinished properly stained C JC JIs ext Unfinished sealed w polurethane 2C Is interior properly painted C OC Is interior stained J JIs interior stain covered w polurethane Ois exterior paint stain lapped onto glass JC Is interior paint stain lapped onto glass L JL JAre TOP
12. warranted for the remainder of the original warranty period This Limited Warranty will be voided and of no force and effect by any of the following conditions Improper installation of the door unit Installation in a non vertical or sloped application Damage from accident misuse or abuse Alteration or use for a purpose other than that for which it was intended e Application of any tint UV limiting or sun blocking film to the interior or exterior of the glass Use of film shades Use in or around ships boats trailers campers swimming pools saunas or greenhouses Installation above 5 000 ft above sea level unless high altitude breather tubes have been factory installed Failure to properly finish all wood exterior surfaces and all interior surfaces within 30 days of purchase according to Woodgrain Millwork s written finishing instructions that accompany every unit Failure to regularly clean exterior cladding when product is installed in a corrosive environment Exposure to harmful chemicals Field mulling connecting of units EXCLUSIONS The following items are not warranted 1 Any labor for repair or replacement of defective parts or glass or any repainting or refinishing 2 Freight replacement parts will be shipped to the closest distributor at Woodgrain Millwork s expense or to the homeowner at their expense Glass breakage including stress cracks Brass Hardware finishes Wood texture
13. ALS WHEREAS Complainant s have a complaint against Woodgrain Millwork of 1001 Ed Rutherford Rd Greenville Texas 75401 concerning Patio Doors purchased by the Complainants WHEREAS Complainants were seeking repairs of alleged warranty defects in the Patio Doors purchased by the Complainants WHEREAS in order to avoid the expense inconvenience uncertainty and distraction of litigation Complainants have agreed to accept the completed field repairs and further have agreed to withdraw their complaint in order to resolve all claims between the parties that were or that could have been raised and to release fully finally and completely all such claims NOW THEREFORE for and in consideration of the mutual covenants releases and conditions contained herein the receipt and sufficiency of which hereby is acknowledged Complainants and Woodgrain Millwork hereby agree as follows Complainants completely RELEASE ACQUIT AND FOREVER DISCHARGE Woodgrain Millwork and its divisions subsidiaries parent corporations in interest and assigns Released Parties from any and all claims demands obligations actions causes of action rights damages or expenses of any nalure whatsoever which are the subject of the above referenced matter including without limitation all known claims for property damage manufacturing defects replacement costs warranty claims or other expenses of any kind relating to any product manufactured or supplied by the Rel
14. e services within one week of completion of the services Contractor shall not be entitled to any progress payments Payment will be due upon completion of the services and salisfaction of all of Contractors obligations under the Contract Documents including correction of any defective or nonconforming repair services Payment shall be due within 30 days of receipt of Cantractor s itemized invoice for completed services 5 STANDARDS Contractor agrees to perform all repair services to Woodgrain s reasonable standards to furnish at all times an adequate supply of equipment to perform the services to perform the services in the best way and most expeditious and economical manner consistent with the interests of Woodgrain Contractor represents and warrants to Woodgrain that it has sufficient technical expertise to perform the repair services required under the Contract Documents 6 GOVERNMENTAL APPROVALS Contractor has obtained ar will obtain at Contractors sole cost and expense all necessary permits and approvals from all appropriate governmental agencies or authorities for the performance of the services Contractor shall perform the services in such a manner that no law ordinance rule or regulation of any governmental agency will be violated 7 INSURANCE Contractor shall maintain the following insurance coverages during the term of the Contract Documents and shall name Woodgrain as an additional insured General Liability insu
15. eased Parties 2 Upon execution of this agreement Complainants agree that the issues conceming patio doors purchased by Complainants are withdrawn and this matter has been settled 3 Complainants understand and agree that the completed field service work is the sole consideration for this Agreement that the consideration stated herein ts contractual and not mere recital and that all agreements and understandings of the parties are embodied and expressed in the Release and thai no representation of any kind was made to Complainants with respect to this settlement by Woodgrain Millwork Woodgrain Millwork s counsel or anyone acting on behalf of Woodgrain Millwork further acknowledge that they are executing this Agreement of their own free will and with complete understanding of the legal consequences of same 4 This Agreement shall be construed and interpreted in accordance with the laws of the State of Texas 5 Complainants acknowledge that this Agreement constitutes the entire agreement between Complainants and the Released Parties and shall be binding upon and inure to the benefit of the executors administrators personal representatives heirs successors and assigns of each Complainants further acknowledge that this Agreement may not be altered or amended without written consent from all parties lt is understood and agreed that this Agreement may be executed in a number of identical counterparts each of which shall be deemed original fo
16. ench into roller pin 3 Rotate wrench to adjust Insert allen I wrench and turn to adjust a vertically and horizontallv Woodgrain Millwork Field SVC Manual 12 05 30 1 3 4 Adjusting roller Remove white caps on bottom of panel Insert screw driver into roller Turn screw driver to raise or lower rollers in panel until panel and strike jamb are parallel Replace caps From the inside of the operating panel remove the white caps and turn the adjustment screws Woodgrain Millwork Field SVC Manual 12 05 31 Adjust sliding door latch 1 Open panel 2 Turn screw in edge of lock to move latch towards or away from the jamb Turning the screw in the lockset moves the latch closer or farther away from the panel Woodgrain Millwork Field SVC Manual 12 05 32
17. erms and conditions under which Contractor will provide repair services on Woodgqgrain s installed windows and doors T CONTRACT DOCUMENTS The Contract Documents consist of this Agreement General Terms and Condilions one or more Work Orders which may be issued from time to time to Contractor by Woodgrain Exhibit A Schedule for Labor Rates attached hereto and any other documents referred to in this Agreement and in any modifications and change orders issued after execution of this Agreement The Contract Documents represent the entire and integrated agreement between the parties and supersede prior negotiations representations or agreements whether written or oral If anything in the other Contract Documents s inconsistent with this Agreement the specific provisions of this Agreement shall govern and control 2 SCOPE OF WORK Contractor shall provide the repair services described in the Contract Documents Contractor will perform such services for the hourly rate s for travel and on site labor and will receive a mileage rate all as set forth on Exhibit A hereto Any additional charges not specifically set forth on Exhibit A for boarding materials and other items must be pre approved in writing by an authorized Woodgrain representative Under no circumstances will Woodgrain pay for meals for Contractor and or its employees if any J SERVICES 3 1 Woodgrain shall at its sole cost and expense provide Cont
18. laims may also be filed on line at www atriumpatiodoor com You must notify Woodgrain Millwork Field SVC Manual 12 05 10 Woodgrain Millwork of any defects within a reasonable period but no later than 30 days after the defect is discovered or should have been discovered Woodgrain Millwork 5700 Enterprise Dr Greenville TX 75402 800 935 2000 atriumcustomerservice woodgrain com www atriumpatiodoors com Woodgrain Millwork Field SVC Manual 12 05 1 Replace Swing Panel Standard Hinges 1 Assure new panel matches the size and handing of the existing panel 2 Remove existing hardware 3 Close Door 4 Remove pins from existing hinges starting at the bottom hinge working your way up the door 5 Remove panel 6 Transfer top and bottom hinges from existing panel to the new panel in the same hinge location 7 Install new panel in frame Set top and bottom hinge pins 8 Install center hinges on panel set hinge pins 9 Install hardware Note In case hinges do not line up back hinge screws out 1 2 of a turn The hinges can then be moved slightly RE TIGHTEN HINGES Caution When installing screws do not over tighten Adjustable Hinge 1 Assure new panel matches the size and handing of the existing panel 2 Remove existing hardware 3 Support panel with wedge from bottom 4 Remove hinge screws ON PANEL Remove screws from the top hinge last 5 Support new panel on wedge and align hinges 6
19. r all purposes WE HAVE READ THIS SETTLEMENT AGREEMENT CAREFULLY AND FULLY UNDERSTAND ALL TERMS SET FORTH THEREIN AND AGREE TO ABIDE BY SAME SIGNED this day of 20 Complainants Signature Woodgrain Millwork Field SVC Manual 12 05 5 3700 Enterprise Drive Greenville Texas 7540 Phone 800 935 2000 L Fax 20463720724 woodgrain millwork cce tiles Atrium Patio Door Field Inspection Form In Store Inspections use Pg 1 All Field Inspections Use Pgs 1 amp 2 Date By Store 5 Purchase Installation Contact Units Involved Prep Code PO amp Code Night PRODUCT CHECK APPROPRIATE BOXES SPECIFICATIONS 02 PNL CS 22 PNL JH 73 PNL ES O Other E Unit Height D6 8 D Handing 611 0o80 C2PNL D4PNL C Other Specify Sueco O1 Lt DACL OWD Grille GFlat Int O CLASSIC Handing Cont int ing O Lo E Plus i OColor PRO SLIDER OFXD OCLAD Other Specify Exterior OWH OST OET OGR OBZ Handing Color OUNFINISHED TRANSOM ORECT OHALF ROUND GELLIPTICAL ac O Colonial O Prairie Ci Plaza MCLAD O Factory Mulled J Field Mulled Number of lites GENERAL PROBLEMS OSEAL FAILURE OWARPING DHARDWARE GLEAKS INSTALLATION DESCRIPTION OF PROBLEM Draw Diagram of customers unit showing reported problem Woodgrain Millwork Field SVC Manual 12 05 6 Atrium Patio Door Field Inspection Form Page 2 Customer Name Y N Door Operation Jats sill straight ls unit plumb Cheek all jambs and mull
20. ractor with replacement parts for windows and or doors at such time as Woodgrain issues a Work Order to Contractor Prior to the performance of any repair services on sile at a customer s location Contractor shall check the accuracy and condition of the replacement parts received from Woodgrain Contractor shall not schedule an on site service with the customer without first inspecting the replacement parts Contractor agrees that it will not be paid for the cost of any unsuccessful on site service trips resulting from Contractor s failure to pre inspect the replacement parts 3 2 Contractor agrees to schedule an on site service visit with the customer within 24 hours following inspection of the replacement parts Any cosis incurred by Woodgrain resulting from Contractors failure to contact the customer within such 24 hour period will be borne solely by Contractor Boisc 166066 1 0010897 00001 Woodgrain Millwork Field SVC Manual 12 05 WOODGRAIN MILLWORK INC SERVICES AGREEMENT GENERAL TERMS AND CONDITIONS 3 3 Upon completion of the services Contractor shall use its best efforts to obtain a release and acceptance agreement from the customer in form provided by Woodgrain 3 4 Contractor shall provide Woodgrain with a weekly update as to the status of all open service claims that have been assigned to Contractor through Work Orders issued by Woodgrain 4 PAYMENT Contractor shall provide Woodgrain with an itemized invoice for th
21. rance with a limit of liability of not less than 31 million per occurrence Auto Liability insurance with combined single limit of not less than 1 million and Workers Compensation Insurance with statutory limits for work related accidents and a minimum of 500 000 Employers Liability coverage All insurance provided by Contractor shall be primary and noncontributory as lo insurance of the additional insureds Coverage shall be on an occurrence basis with the products and completed operations coverage to be maintained for no less than three years after substantial completion No less frequently than annually or with such greater frequency as Woodgrain may reasonably request or as may be dictated by circumstances including upon any change in any required insurance carried by Contractor Contractor will furnish Woodgrain with certificates of insurance showing such coverages and naming Woodgrain as an additional insured and evidence of payment of all required premiums X Each certificate must have a minimum 30 day written cancellation notice clause in favor of Woodgrain and be in form reasonably acceptable to to Woodgrain B INDEMNITY Contractor wil on demand indemnify and hold harmless Woodgrain and its affiliates and representatives from all losses as defined below that any of them may incur arising out of the services provided by Contractor under the Contract Documents or Contractor s failure to comply with any provisions of the
22. re that silicone has sealed the glass fully against the glass shelf 10 Reinsert side and top black spacers in the same location where they were installed in the factory 11 Reinstall glazing bead top bottom then the sides Glazing bead may need to be trimmed or sanded to fit 12 Secure glazing bead with brads or staples Caution If the glass 1s hit with the 13 brads or staples it WILL SHATTER Woodgrain Millwork Field SVC Manual 12 05 20 Replace ACL Bars 1 Insert putty knife thru the double sided tape that hold the bar onto the glass 3 Clean glass with razor blade and alcohol GLASS MUST BE CLEAN AND DRY or new bars will not stick 4 Assemble bars 5 Dry fit bar to glass trim if necessary 6 Remove blue tape backing from the first 3 of the ACL bar 7 Place the ACL bar on the glass 8 From the top of the ACL bar begin peeling back the blue backing tape removing it from the bar 9 Manually press HARD the ACL bar onto the glass Woodgrain Millwork Field SVC Manual 12 05 21 Replace a sill cover 1 Determine if astragal needs to be removed as it may be resting on top of the sill COVer 2 Insert narrow flat bar or wide tip flat screw driver between sill cover and sill Pry sill cover up to remove If the sill cover releases proceed to step 5 3 Insert Phillips screw driver into weep 4 Tap screw driver to release the sill cover 5 Set sill cover into position on sill 6 Apply
23. reof The arrangements contemplated by the Contract Documents shall be terminable by mutual agreement of the parties and may be terminated unilaterally by either of the parties with or without cause and for any reason or no reason by 30 days advance written notice of terminalion to the other Any such termination shall be effective on the date 30 days after the effective date of such notice under Section 13 or any later effective dale specified in such notice Upon termination Contractor shall be entitled Boise 166066 1 0010807 00001 Woodgrain Millwork Field SVC Manual 12 05 to payment for ail completed services prior to the effective date of termination 13 NOTICES Notices under this Agreement shall be in writing effective when delivered or if mailed affective on the third day after mailed postage prepaid to the address for the party stated in this Agreement or to such other address as either party may specify by notice to the other 14 ATTORNEYS FEES In the event suit or action is instituted to interpret or enforce the terms of the Contract Documents the prevailing party shall be entitled to recover from the other party such sum as the court may adjudge reasonable as attorneys fees at trial upon appeal and on any petition for review in addition to all such sums provided by law 15 CONFIDENTIALITY Contractor agrees not to disclose any information regarding past claims or known product problems affecting Woodgrain
24. rew 3 Place cardboard drywall shims between the hinge and the jamb As shown 4 Tighten and reinstall screws 5 Close panel and check reveal Woodgrain Millwork Fie 14 Adjusting adjustable hinges When adjusting use a hand screwdriver Adjust the vertical margins by adjusting the center hinge Adjust the horizontal margins by adjusting the top and bottom hinges Top hinge adjusts gt l Center hinge adjusts Bottom hinge adjusts 4 gt Woodgrain Millwork Field SVC Manual 12 05 15 Replace pro French astragal 1 Remove secondary panel from unit 2 Remove plastic astragal cap from astragal 3 Slide aluminum astragal cap off of astragal may require some force 4 Remove screws that hold astragal on the panel 5 Repeat steps 1 thru 4 in reverse order using new parts Woodgrain Millwork Field SVC Manual 12 05 16 Replace Design Series French Astragal 1 Open primary panel 2 Remove black head screws that hold the wood astragal on Open primary panel and remove these screws on the secondary panel 3 The wood and aluminum astragals can then be removed 4 Install new astragal with original screws Woodgrain Millwork Field SVC Manual 12 05 17 Replace center swing astragal 1 Open door 2 Insert flat screw driver between astragal and astragal cap as shown 3 Pry astragal cap off 4 Remove screws that hold the astragal on 5 Remove astragal 6 Repeat steps 1 thr
25. steps 1 thru 3 in reverse to reassemble Woodgrain Millwork Field SVC Manual 12 05 26 Replace Sliding handleset 1 Support handleset on the exterior of the unit 2 From the inside remove screws that hold the faceplace on 3 Remove handleset 4 Repeat steps 1 thru 3 in reverse to reinstall Woodgrain Millwork Field SVC Manual 12 05 PA Replace interlock weatherstripping Caution Do not damage bottom weatherstripping 1 Remove operable sliding panel 2 Lay panel on lock side 3 Remove screws that hold the interlock in place 4 Remove existing interlock 5 Repeat steps thru 4 in reverse Woodgrain Millwork Field SVC Manual 12 05 28 1 3 4 5 6 7 8 9 Pull here to extend latch bolt Replace multipoint lock Primary panel Open panel Remove handleset See replacing swing handleset instructions Remove Phillip Head screws ONLY in the edge of the panel Remove lockest Place new lockset into edge of door Place exterior trim assembly into lockset THIS LOCATES THE LOCK IN THE DOOR Replace Phillips head screws in the edge of the door Leave the top two screws out Lift handle to lock Extend the lock extension 11 Install remaining screws 12 Reinstall Handleset See replacing swing handleset instructions 13 Operate lock assembly to assure it works Woodgrain Millwork Field SVC Manual 12 05 29 Adjust multi point lock Sidelite 1 Open panel 2 Insert allen wr
26. u 5 in reverse order to install Woodgrain Millwork Field SVC Manual 12 05 18 1 2 3 4 5 6 T Replace Swing Door Sweep Remove panel by following panel replacement instructions Pull sweep off of the panel Remove existing staples from the panel Apply 2 beads of silicone to the bottom of the panel Trim and or notch sweep to fit door and not interfere with any hardware that is installed Apply new sweep make sure you install in same position as the original Staple or screw new sweep onto panel 7 Install panel Caution Do not use screws that will damage the sill threshold Woodgrain Millwork Field SVC Manual 12 05 19 Replace glass CAUTION Be careful not to damage the wood portion of the door panel 1 Remove Glazing bead carefully MAY NEED TO BE REUSED 2 Inspect opening to assure that no staples are showing If so remove them 3 From exterior side cut sealant with a razor knife or narrow and flexible putty knife 4 From the side of the door begin working the glass loose from the top of the panel Support the inside of the glass with your opposite hand 5 Remove existing silicone from metal glass shelf 6 Apply 4 bead of silicone to the metal glass shelf l4 Bead of Silicone 7 Reinsert black spacers at the bottom of the glass opening in same location where they were installed in the factory 8 Set glass in opening and seat against metal glass shelf 9 Look thru glass to assu
Download Pdf Manuals
Related Search