(a) (b) (c) (d) (e)
Contents
1. MAN 10 100 100 FDX Port forced to 100 FDX MAN 10 100 100 HDX Port forced to 100 HDX MAN 10 100 10 FDX Port forced to 10 FDX MAN 10 100 10 HDX Port forced to 10 HDX When the module is configured for auto negotiation the module will advertise in the order shown in the parenthesis Page 7 lt BLACK BOX FlexPoint Triple Speed 10 100 1000 UTP to 100 1000X Ethernet Media Converter User Manual International Power Supplies LMC1017AE US Power Supplies LMC1017A SFP LMC1017A MMST LMC1017A MMSC LMC1017A SMST LMC1017A SMSC LMC1017A SMSC LH CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT outside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com POWER ADAPTER NOTICE 1 This product should only be used with Black Box Supplied Power Unit model numbers PWPB112511 US or LMC203A Universal 2 When used in a standalone configuration this product must be used with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp NOTE If mounting with a safety ground attachment use the safety ground screw at the rear of the unit Page 1 LED INDICATORS LED Function On Blinking State Legend Color Off State Power Test On Module has power2. for g AN but in manual mode UTP Speed 100 On UTP port linked at 100Mbps UTP 100 Blinking 10Hz Link activity UTP Speed 1000 UTP 1000 On UTP port linked at 1000Mbps Blinking 10Hz Link activity On UTP port linked at 10Mbps UTP Speed 10 Blinking 10Hz Link activity UTP 100 aa Pattern Blinking Detecting UTP 1000 remote_fault AN on UTP port UTP Auto Neg ae i e 100 Blinking 1Hz Unable to establish HER 108 AN link on the UTP port UTP 1000 Page 8 FlexPoint Triple Speed RX RX Xx UTP Fiber UTP N Fiber lt 1X RX IX BX Normal Mode Loopback Mode Figure 1 Loopback Mode LINK MODES In order to accommodate different user needs the Triple Speed supports four different link modes see Fig 2 In Link Segment LS a port transmits a Link signal independently of any received Link at any other port For example the UTP transmits a Link regardless of the fiber receiving a Link Fig 2 a amp b In Link Propagate LP a port transmits a Link signal only when receiving a Link at its other port For example the UTP transmits a Link only when receiving a Link at the fiber port Fig 2 c In Remote Fault Detection Link Segment RFD LS the fiber port transmits a Link signal only when receiving a Link at the fiber port As a result fiber faults no Link received at the fiber are looped back and can be reported to the ne
3. lt BLACK BOX FlexPoint Triple Speed 10 100 1000 UTP to 100 1000X Ethernet Media Converter User Manual International Power Supplies LMC1017AE US Power Supplies LMC1017A SFP LMC1017A MMST LMC1017A MMSC LMC1017A SMST LMC1017A SMSC LMC1017A SMSC LH CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT outside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com POWER ADAPTER NOTICE 1 This product should only be used with Black Box Supplied Power Unit model numbers PWPB112511 US or LMC203A Universal 2 When used in a standalone configuration this product must be used with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp NOTE If mounting with a safety ground attachment use the safety ground screw at the rear of the unit Page 1 UTP MODES Sw3 sw4 SW5 Sw6 UTP Mode of Operation AN MAN 10 100 10 100 FDx HDx 1000 AN 1000 NA FDX Configured for Auto Negotiation 1000F 1000H 100F 100H 10F 10H AN HDX Configured for Auto Negotiation 1000H 100F 100H 10F 10H AN FDX Configured for Auto Negotiation 100F 100H 10F 10H AN HDX Configured for Auto Negotiation 100H 10F 10H AN FDX Configured fo
4. mode LP LS Enables Remote Fault Detection mode plus Link Segment mode RFD LS LP RFD Enables Remote Fault Detection mode plus Link Propagation mode RFD LP NOTE RFD is only available when the fiber port is operating in manual mode REMOTE FAULT Each port will generate an IEEE remote_fault indicator when the incoming signal to the port is lost When a port is configured for auto negotiation it will set the remote fault bit high in the AN advertisement when the port detects a loss of incoming signal See LED Indicators table on page 8 for specifics on how the unit reports the detection of this signal When the fiber port is operating in 100BASE FX a loss of incoming signal will cause the port to generate a Far End Fault indicator pattern See LED Indicators table on page 8 for specifics on how the unit reports the detection of this signal Page 6 12 Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El c
5. n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han caido o liquido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la luvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada Form 040 L1017 001C 1 11 Page 12 Loopback Off On DIP Switch Setting this DIP switch On enables loopback on the fiber and UTP ports see Figure 1 Link Modes See the following table for configuring link modes sw9 Sw10 Result LS LP RFD Normal LS Normal Enables Link Segment mode LS LP Normal Enables Link Propagate mode LP Ls RFD Enables Remote Fault Detection mode plus Link Segment mode RFD LS LP RFD Enables Remote Fault Detection mode plus Link Propagation mode RFD LP NOTE RFD is only available when the fiber port is operating in manual mode REMOTE FAULT Each port will generate an IEEE remote_fault indicator when the incoming signal to the port is lost When a port is configured for auto negotiation it will set the remote fault bit high in the AN advertisement when the port detects a loss of incoming signal See LED Indicators table on page 8 for specifics on how the unit reports the detection of this signal When the fiber port is operating in 100BASE FX a loss of inc
6. the UTP transmits a Link regardless of the fiber receiving a Link Fig 2 a amp b In Link Propagate LP a port transmits a Link signal only when receiving a Link at its other port For example the UTP transmits a Link only when receiving a Link at the fiber port Fig 2 c In Remote Fault Detection Link Segment RFD LS the fiber port transmits a Link signal only when receiving a Link at the fiber port As a result fiber faults no Link received at the fiber are looped back and can be reported to the network core Fig 2 d In Remote Fault Detection Link Propagate RFD LP the UTP port transmits a Link signal only when receiving a Link at the fiber port The fiber port transmits a Link signal only when receiving Link signals at both the fiber port and the UTP port As a result fiber faults no Link received at the fiber are propagated forward and looped back for fault reporting at both the network core and the customer location Fig 2 e NOTE Connecting two converters with both set to RFD mode is not supported and will cause a deadly embrace lockup Page 3 TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in stric
7. Switch 2 LP LP gt O X gt Xx gt D c O je Oje Oje Switch 1 Converter A Converter B Switch 2 LP RFD LS gt o mxx gt d WI Wi O Switch 1 Converter A ConverterB Switch 2 LP RFD LP gt O lt P e Wl Whe ole Switch 1 Converter A Converter B Switch 2 LEDOn YX LED Off O LED Status depends on connected device Figure 2 Link Modes Page 4 NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante 7 Elaparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser re
8. able de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada Form 040 L1017 001C 1 11 Page 12 UTP MODES sw3 sw4 SW5 Sw6 UTP Mode of Operation AN MAN 10 100 10 100 FDx HDx 1000 AN 1000 NA FDX Configured for Auto Negotiation 1000F 1000H 100F 100H 10F 10H AN 1000 NA HDX Configured for Auto Negotiation 1000H 100F 100H 10F 10H AN 10 100 100 FDX Configured for Auto Negotiation 100F 100H 10F 10H AN 10 100 100 HDX Configured for Auto Negotiation 100H 10F 10H AN 10 100 10 FDX Configured for Auto Negotiation 10F 10H AN 10 100 10 HDX Configured for Auto Negotiation 10H MAN 1000 NA FDX Configured for Auto Negotiation 1000F When the port is set to 1000 it is always in AN mode MAN 1000 NA HDX Configured for Auto Negotiation 1000H When the port is set to 1000 it is always in AN mode
9. blish UIP 199 Green IAN link on the UTP port UTP 1000 Page 8 NOTE Remove safety ground screw when installing the module in the 14 Module Chassis or when using it with the DC DC Converter Model LMC204A WARNING Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source INSTALLATION PROCEDURE 1 Configure the appropriate FlexPoint Triple Speed DIP Switch settings 2 Connect the UTP port via a Category 5 or better cable to a 10BASE T 100BASE TX or 1000BASE T Ethernet device 3 When using fixed fiber port models connect the appropriate multimode or single mode fiber cable to the fiber port of the installed module Itis important to ensure that the transmit Tx is attached to the receive side of the device at the other end and the receive Rx is attached to the transmit side 4 When using the SFP model insert the SFP Fiber transceiver into the Port 1 SFP receptacle on the Triple Speed NOTE The release latch of the SFP Fiber transceiver must be in the closed up position before insertion Connect the appropriate multimode or single mode fiber cable to the fiber port of the installed module LOOPBACK The FlexPoint Triple Speed has the capability to provide loopback to aid in installation and maintenance A DIP switch is used to enable loopback on the module see page 6 Figure 1 shows the module in normal and loopbac
10. ceiver into the Port 1 SFP receptacle on the Triple Speed NOTE The release latch of the SFP Fiber transceiver must be in the closed up position before insertion Connect the appropriate multimode or single mode fiber cable to the fiber port of the installed module LOOPBACK The FlexPoint Triple Speed has the capability to provide loopback to aid in installation and maintenance A DIP switch is used to enable loopback on the module see page 6 Figure 1 shows the module in normal and loopback modes Page 2 LED INDICATORS poa Color Off State On Blinking State On Module has power Power Test Blinking Module in loopback Power Green No power mode On Fiber port configured for AN F O AN Green Port configured for Blinking Fiber port configured for F O Auto Neg manual negotiation AN but establishe link in manual mode On Fiber port linked at 100Mbps Blinking 10Hz Link activity at F O Speed 100 Green Not connected at 100Mbps F O 100 100Mbps Blinking 1Hz Signal detected but port unable to establish a link On Fiber port linked at 1000Mbps Blinking 10Hz Link activity at 1000Mbps F O Speed 1000 Not connected at F O 1000 1000Mbps Blinking 1Hz Signal detected but port unable to establish a link Pattern Blinking AN remote Fault bit detected UTP Duplex p A UTP FDX Half Duplex On UTP port in Full Duplex On UTP port configured for AN TEON oaj Blinking UTP port configured
11. e connected device Configure both devices to Manual mode to establish a link F O Speed 100 1000 DIP Switch The Triple Speed supports 100BASE FX and 1000BASE X SFPs This DIP switch is used to configure the unit for the speed of SFP used Setting this DIP switch to 1000 enables the fiber port is accept 1000BASE X SFPs Setting this DIP switch to 100 enables the fiber port to accept 100BASE FX SFPs UTP Configuration DIP Switches See the UTP Modes table on page 7 Pause On Off DIP Switch In auto negotiation mode setting this DIP switch to On allows the unit to advertise as Symmetrical and Asymmetrical Pause capability In auto negotiation mode setting the DIP switch to Off causes the unit to advertise no Pause capability In the manual mode this DIP switch determines the Symmetrical Pause behavior Page 5 NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de u
12. ferido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato N tn p Page 11 DIP SWITCHES F O Manual Auto Man AN DIP Switch Setting this DIP Switch to Auto Negotiate AN factory setting enables the fiber port to determine duplex mode automatically If the connected device cannot provide the proper signal to indicate its own mode of operation set this DIP Switch to Manual MAN This feature allows connections with legacy manual negotiation devices that do not support auto negotiation NOTE When the fiber port is configured for Manual Mode a link may not occur with the connected device Configure both devices to Manual mode to establish a link F O Speed 100 1000 DIP Switch The Triple Speed supports 100BASE FX and 1000BASE X SFPs This DIP switch is u
13. k modes Page 2 SPECIFICATIONS Model Type Triple Speed IEEE 802 3 Protocols 10BASE T 100BASE TX 1000BASE T 100BASE FX 1000BASE X JFrame Size 10 240 byte max frame size UTP Cable RJ 45 Category 5 and higher 5 Multimode 50 125 62 5 125 100 140um Fiber Cables Single mode 9 125 um UTP Connectors RJ 45 Fiber Auto Neg 1000 100 UTP Auto Neg 10 100 1000 FDX HDX Pause En Dis Loopback Link Seg Link Prop Remote Fault Det Power Fiber AN Fiber Speed Activity UTP Speed Activity LED Displays Ful Half Duplex W 3 0 x D 4 0 x H 1 0 weim 6 oz without power adapter Compliance UL CE FCC Class A Barrel Molex Connector Connector Power Requirements Nominal Voltage 9VDC 5VDC Voltage Range 5 0 to 32 0VDC 5 0 to 32 0VDC Nominal Power 0 3A 9VDC 0 5A 5VDC Maximum Power 1A 9VDC 0 75A 5VDC Humidity 5 to 95 non condensing MTBF Hours Module without Power Adapter 900 000 Module with Power Adapter 1 250 000 Module with Power Adapter 2 100 000 Page 9 FlexPoint Triple Speed RX _ xX RX IX UTP Fiber UTP Fiber IX RX TX le RX_ Normal Mode Loopback Mode Figure 1 Loopback Mode LINK MODES In order to accommodate different user needs the Triple Speed supports four different link modes see Fig 2 In Link Segment LS a port transmits a Link signal independently of any received Link at any other port For example
14. na alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante 7 Elaparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Page 11 Loopback Off On DIP Switch Setting this DIP switch On enables loopback on the fiber and UTP ports see Figure 1 Link Modes See the following table for configuring link modes Sw9 Sw10 Result LS LP RFD Normal LS Normal Enables Link Segment mode LS LP Enables Link Propagate
15. oming signal will cause the port to generate a Far End Fault indicator pattern See LED Indicators table on page 8 for specifics on how the unit reports the detection of this signal Page 6
16. p m Green No power Blinking Module in loopback ower mode On Fiber port configured for AN F O AN Green Port configured for Blinking Fiber port configured for F O Auto Neg manual negotiation AN but establishe link in manual mode On Fiber port linked at 100Mbps Blinking 10Hz Link activity at F O Speed 100 Not connected at 100Mbps oaio Green p Blinking 1Hz Signal detected but port unable to establish a link On Fiber port linked at 1000Mbps Blinking 10Hz Link activity at 1000Mbps F O Speed 1000 Green Not connected at F O 1000 1000Mbps Blinking 1Hz Signal detected but port unable to establish a link Pattern Blinking AN remote Fault bit detected UTP Duplex n ii UTP FDX Green Half Duplex On UTP port in Full Duplex UTP AN Port configured for On UTP port configured for AN Green Blinking UTP port configured for FUTP Auto Neg JAN but in manual mode manual negotiation UTP Speed 100 UTP 100 Not connected at On UTP port linked at 100Mbps Green ooMbps Blinking 10Hz Link activity UTP Speed 1000 Not connected at On UTP port linked at 1000Mbps Green UTP 1000 1000Mbps Blinking 10Hz Link activity On UTP port linked at 10Mbps UTP Speed 10 tare tr tae UTP 100 Not connected at Blinking 10Hz Link activity Green oMpps UTP 1000 Pattern Blinking Detecting remote_fault AN on UTP port UTP Auto Neg aie n 100 Blinking 1Hz Unable to esta
17. r Auto Negotiation 10F 10H AN HDX Configured for Auto Negotiation 10H MAN FDX Configured for Auto Negotiation 1000F When the port is set to 1000 itis always in AN mode MAN HDX Configured for Auto Negotiation 1000H When the port is set to 1000 it is always in AN mode MAN FDX Portforced to 100 FDX MAN HDX Port forced to 100 HDX MAN FDX Portforced to 10 FDX MAN 10 100 10 HDX Portforced to 10 HDX When the module is configured for auto negotiation the module will advertise in the order shown in the parenthesis Page 7 NOTE Remove safety ground screw when installing the module in the 14 Module Chassis or when using it with the DC DC Converter Model LMC204A WARNING Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source INSTALLATION PROCEDURE 1 Configure the appropriate FlexPoint Triple Speed DIP Switch settings 2 Connect the UTP port via a Category 5 or better cable to a 10BASE T 100BASE TX or 1000BASE T Ethernet device 3 When using fixed fiber port models connect the appropriate multimode or single mode fiber cable to the fiber port of the installed module It is important to ensure that the transmit Tx is attached to the receive side of the device at the other end and the receive Rx is attached to the transmit side 4 When using the SFP model insert the SFP Fiber trans
18. rotection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada Page 10 DIP SWITCHES F O Manual Auto Man AN DIP Switch Setting this DIP Switch to Auto Negotiate AN factory setting enables the fiber port to determine duplex mode automatically If the connected device cannot provide the proper signal to indicate its own mode of operation set this DIP Switch to Manual MAN This feature allows connections with legacy manual negotiation devices that do not support auto negotiation NOTE When the fiber port is configured for Manual Mode a link may not occur with th
19. sed to configure the unit for the speed of SFP used Setting this DIP switch to 1000 enables the fiber port is accept 1O00BASE X SFPs Setting this DIP switch to 100 enables the fiber port to accept 100BASE FX SFPs UTP Configuration DIP Switches See the UTP Modes table on page 7 Pause On Off DIP Switch In auto negotiation mode setting this DIP switch to On allows the unit to advertise as Symmetrical and Asymmetrical Pause capability In auto negotiation mode setting the DIP switch to Off causes the unit to advertise no Pause capability In the manual mode this DIP switch determines the Symmetrical Pause behavior Page 5 12 Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y receptaculos donde salen del aparato 14 El equipo el ctrico debe ser limpiado tinicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci
20. t accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada Page 10 LS LS gt Fiber gt gt a UTP UTP oO ok ob Switch 1 Converter A Converter B Switch 2 LS LS gt gt gt b jq O je jq Switch 1 Converter A Converter B
21. twork core Fig 2 d In Remote Fault Detection Link Propagate RFD LP the UTP port transmits a Link signal only when receiving a Link at the fiber port The fiber port transmits a Link signal only when receiving Link signals at both the fiber port and the UTP port As a result fiber faults no Link received at the fiber are propagated forward and looped back for fault reporting at both the network core and the customer location Fig 2 e NOTE Connecting two converters with both set to RFD mode is not supported and will cause a deadly embrace lockup Page 3 SPECIFICATIONS Model Type Triple Speed IEEE 802 3 Protocols 10BASE T 100BASE TX 1000BASE T 100BASE FX 1000BASE X JFrame Size 10 240 byte max frame size UTP Cable RJ 45 Category 5 and higher F Multimode 50 125 62 5 125 100 140um Fiber Cables Single mode 9 125ym UTP Connectors RJ 45 Fiber Auto Neg 1000 100 UTP Auto Neg 10 100 1000 FDX HDX Pause En Dis Loopback Link Seg Link Prop Remote Fault Det n Power Fiber AN Fiber Speed Activity UTP Speed Activity LED Displays Full Half Duplex W 3 0 x D 4 0 x H 1 0 weit 6 oz without power adapter UL OF FOC mss A Barrel Molex Connector Connector Power Requirements Nominal Voltage 9VDC 5VDC Voltage Range 5 0 to 32 0VDC 5 0 to 32 0VDC Nominal Power 0 3A 9VDC 0 5A 5VDC Maximum Power 1A 9VDC 0 75A 5VDC 5 to 95 non condensing Module without Po
22. wer Adapter 900 000 Module with Power Adapter 1 250 000 Module with Power Adapter 2 100 000 MTBF Hours Page 9 LS LS gt Fiber gt gt a UTP UTP oO ott ob Switch 1 Converter A Converter B Switch 2 LS LS gt gt gt b j4 O je jq Switch 1 Converter A Converter B Switch 2 LP LP gt O xX gt x c O je Oje Oje Switch 1 Converter A Converter B Switch 2 LP RFD LS gt O Xg gt d Wl WI 4 Switch 1 Converter A Converter B Switch 2 LP RFD LP gt O lt P N e Wi We 4 ole Switch 1 Converter A ConverterB Switch 2 LEDOn YX LED Off O LED Status depends on connected device Figure 2 Link Modes Page 4 TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable p
Download Pdf Manuals
Related Search