Manual técnico - Motores Garaje
Contents
1. apertura de la hoja a 90 angle o Tabla3 cotas de montaje actuador EE a d D entre ojales m ximo OP2005 Se aconseja de no elegir valores de A Y B demasiado diferentes entre ellos de este modo se garantiza un movimiento regulado de la hoja con el menor esfuerzo del actuador 8 Cota A Aument ndola se aumenta el ngulo de apertura y en consecuencia disminuye el empuje del actuador pero aumenta la velocidad perif rica 8 Cota B Aument ndola disminuye el ngulo de apertura y en consecuencia aumenta el empuje del actuador pero disminuye la velocidad perif rica 2 3 Posicionamiento soporte posterior y anterior N B Agujerear con broca 1 meter taco 2 apoyar el soportey 3 y atornillar 4 seg n fig OP2007 del manual Definir la posici n de fijaci n del soporte posterior del adtuador respetando las cotas A B y C indicadas en tabla 3 Verificar que la salida del tubo de los cables el ctricos se encuentren bajo el soporte 3 Verificar que sobre la hoja en el lugar donde debe ser fijado el soporte anterior del actuador tengamos sitio para soldar o atornillar Fijar con tornillos o soldadura el soporte posterior al pilar en la posici n establecida 0 0 O W Aum A a e Verificar que el soporte este perfectamente a nivel al Lievar la hoja a la posici n de cierre con el tope mec nico de cierre b1 Posicionar el soporte 1 anterior a la distan2. determinan los l mites de empleo Deben ser atentamente considerados para la instalaci n La tabla 3 tiene los valores s lo indicativos 804 720 Tabla 2 Limites de empelo modelo Largo m ximo hoja Peso m x de hoja kg 1 50 350 3 00 150 2 2 Instalacion tipo 1 INSTALACION DE 2 HOJAS La definici n de hoja 1 y hoja 2 de la cancela es fundamental para el funcionamiento del automatismo Hoja 1 Es la primera en abrirse Fig 2 1 cuando las cancelas est n cerradas mientras que es la segunda en moverse cuando est n abiertas Liega al tope de cierre despu s de la hoja 2 100 107 50 Hoja 2 Es la segunda en abrirse Fig 2 1 cuando las cancelas est n cerradas mientras que es la primera en moverse cuando se encuentran en posici n de hojas abiertas Liega al tope de cerre primero que la hoja 1 lt gt 6 2 INSTALACION DE 1 HOJA Hoja 1 la nica hoja de la cancela Controntar que la cota C en la estructura no sea superior a los valores indicados en la tabla 3 Si la cota supera estos valores es necesario aplicar alguna pr tesis simulada para llegar a los valores indicados en la tabla Esto es para evitar que en cierre el actuador vaya batiendo a golpes hasta llegar al tope En la fig est n indicadas las cotas referidas para el montaje del actuador En la tabla 3 est n los valores de A Y B aconsejados para una
3. EN 301489 3 2001 Electromagnetic compatibility for radio equipment and appliances EN 300220 3 2000 Radio equipment and systems short band devices Technical characteristics and testing methods for radio apparatus with a frequency of 25 to 1000 MHz and powers of up to 500mW Un Un Un Un un un The Manufacturer also declares that it is not permitted for the abovementioned components to be used until such time as the system in which they are incorporated is declared conform to directive 98 37 EC Nominativo del Firmatario MICHELE RUI Qualifica Presidente Firma lt gt 15 lt gt 16 Address Telephone Telefax http e mail home integration Via Sandro Pertini 3 5 31014 COLLE UMBERTO TV ltalia Numero Verde 39 0438 388592 wwwhomeite t 000 046826 info homelife it
4. a PROFESSIONAL FITTER If a fault that cannot be solved following the information contained in the present manual arises contact the manufacturer s assistance service All maintenance repair or replacement of parts must be recorded in the maintenance log which is SUPPLIED AND INITIALLY FILLED IN BY THE FITTER CLEANING AUTOMATION ATTENTION Never wash the operator with jets of water or cleaning devices using water Do not use corrosive substances solvents thinners or spirits to clean the operator 5 Before cleaning switch of the power supply a Automations are almost always installed outdoors and are therefore subject to climatic changes and harsh weather conditions that transport debris that may cause problems b The area in which the automation is installed must be kept clean to avoid malfunctions and faults Keep the gate area clean by using a broom to brush away stones gravel mud etc that deposit there d Keep the opening and closure stop plates clean ROUTINE MAINTENANCE Every 6 months a PROFESSIONAL FITTER should repeat the following operations 5 A series of opening and closure tests using radio controls internal button panels and selectors making all the automation devices function photocells sensitive strips flashing light etc Check that the gate performs the desired action Grease the gate s bearings Repeat the series of tests described for automation testing 7 0 DEMOLITION AND DISPOSA
5. g rain and or foreign bodies earth gravel etc penetrating inside Wrapping materials must be disposed of in compliance with local regulations Wear protective goggles when making holes for clamping In the event of works at heights of over 2m from the ground for example for the installation of the indicator lamp or aerial fitters must be equipped with ladders safety harnesses protective helmet and all other equipment required by law and the standards governing this kind of work Refer to Directive 89 655 EEC amended by 2001 45 EC PRELIMINARY CHECKS Before commencing installation the following checks must be performed 1 The weight and dimensions of the gate must not exceed the limits for use see the TECHNICAL DATA and USAGE RESTRICTIONS chaps if they exceed such limits the OPTIMO operator may not be installed The structure of the gate leaf must be suitable for the installation of the operator and conform to current standards Provide all devices necessary to guarantee safe operation The gate leaves must be sturdy and solid the hinges must be suited to the dimensions and weight of the leaves gaps between parts must be minimal and they must be solidly fixed The gate s movement in both opening and closure must be uniform without points of greater resistance to rotation or friction Check manually by opening and closing the leaves several times The gate leaves mus movement Gate leaf hinges must be perfectly vertical in order t
6. L The OPTIMO operator is constructed using various materials which implies the adoption of different disposal procedures Refer to regulations in force in the country in which the automation is installed Contact qualified firms for disposal un un un ATTENTION the automation may only be disconnected from the mains by a qualified electrician using suitable instruments 14 lt gt 8 0 MANUFACTURER S DECLARATION OF CONFORMITY Declaration of conformity C under Directive 98 37 EC appendix part B Manufacturer s Declaration of CE Conformity LIFE home Integration Via S Pertini 3 5 31014 COLLE UMBERTO TV italla OPTIMO SKY LINE Swinging gate operator satisfies the essential requisites established in the following directives m Machinery Directive 98 37 EC formerly 89 392 EEC and subseguent amendments 8 Low voltage directive 73 23 EEC and subsequent amendments 8 Electromagnetic compatibility directive 89 336 EEC and subsequent amendments and satisfies the following standards EN 12445 2000 Industrial commercial and garage doors and gates Safety in the usage of motorised doors testing methods EN 12453 2000 Industrial commercial and garage doors and gates Safety in the usage of motorised doors Requisites EN 60204 1 1997 Machinery safety Electric equipment of the machine Part 1 general rules EN 60950 Information technology equipment Safety Part 1 General requisites ETSI
7. OPTIMO SKY LINE ACTUADOR LINEAL ELECTROMEC NICO PARA CANCELAS BATIENTES INSTRUCCIONES Y ADVERTENCIAS PARA INSTALACION Y USO home integration 1 Rev 01 09 2011 RT 1 7 5RI17000 2 8 5RI17700 5RI17100 Le 9 lt y 7 5RI17800 A H y P d 4 5 10 5RI17300 4 se 5RI17900 5 11 5RI17400 J 5RI18000 6 O ke 12 SS dd 5RI17500 5RI18000 E 35 4 lt gt 1 0 DATOS T CNICOS OPSL UNI Actuador electromec nico irreversible alimentado a 24 V para puertas OPSL UNI batientes con final carrera mec nicos 230 Vac 50 Hz Alimentaci n 230 Vac Central LIFE GE UNI R S DL GEUNIR Potencia max 160 Absorci n m x 14 Empuje 1800 Lubrificaci n Grasa permanente Final carrera 2 Mec nicos Carrera til del actuador 325 Temperatura de ejercicio da 20 a 70 Grado de protecci n Tiempo para abrir a 90 Ciclo de trabajo Peso actuador Dimensiones 804X807X100 Uso en atmosfera cida salina o potencialmente corrosiva no Largo m ximo y peso m x hoja 3m 150kg 1m 350kg 5 lt gt 2 0 INSTALACION 2 1 L mites de empleo EL tipo de cancela la altura y la forma de las hojas las condiciones clim ticas
8. cia E del soporte posterior menor de 50 mm seg n ilustraci n en Tabla 4 Cotas D y E de instalaci n Cota D 710 mm Max Cota E 50 mm El valor de E tienen que ser apenas inferior 10 m m de D para permitir una mejor regulaci n de los finales de carrera c1 Bloquear provisionalmente el soporte anterior con un sargento 2 d1 Verificar que el soporte est a nivel seg n ilustraci n en fig 4 7 lt gt 2 4 Posicionamiento actuadory regulacion finales de carrera 1 Efectuar el bloque del actuador seg n indicado en cap tulo DESBLOQUEO ACTUADOR Para desbloquear el actuador meter la chaveta 1 y girar a 360 anti horario El actuador quedar desbloqueado seg n figura OP2009 360 Desbloqueo 2 Sacar cobertor 3 destornillando 1 dando un golpe hacia delante para desengancharlo de los encastes Desatornillar 4 y guiar el cobertor por el visin fin 5 4 10 11 12 Meter el encaste en el ojo 5 del soporte posterior 3 y ensartar la horquilla del actuador 6 sobre el soporte 3 haciendo coincidir el agujero con el encaste meter tornillo 7 y apretar con el dado autoblocante 8 ver figura Fijar el actuador 6 al soporte anterior 3 con tornillo Abrir y cerrar a mano la cancela m s veces y verificar que el movimiento de la hoja es regular y que el actuador se mueva un plano paralelo al plano de movimiento de la puerta Controlar que el sopor
9. compliance with the intended use in the awareness of safety and hazard conditions and in compliance with the instructions for installation and use s Any dysfunctions that may pose threats to safety must be eliminated immediately s The gate must be stable properly hung and resistant to flexion it must not bend during opening and closure movements s The operator cannot compensate for faulty or incorrectly hung gates The operator may not be used in environments prone to flooding 5 Do not use the operator in environmental conditions characterised by harsh atmospheric agents e g salty air 5 0 SAFETY INSTRUCTIONS AND WARNINGS GENERAL INSTRUCTIONS AND WARNINGS s The Manufacturer declines responsibility for damage or injury caused by non conformity with the information supplied concerning installation trial run use and maintenance contained in this manual and the failure to observe the safety instructions given below S The installation connection testing trial run and maintenance of the operator must be performed by a COMPETENT PERSON aided and supervised by a PROFESSIONAL FITTER S Given the technical procedural regulation and legal implications of the work unauthorised fitters are not permitted Installation reguires a practical and theoretical knowledge of mechanics electronics and electrics and of sector laws and standards S Amateur installation IS STRICTLY FORBIDDEN as it does not comply with current standards and laws and the
10. he electricity supply and contact the Manufacturer s Assistance Service immediately use of the operator in such conditions may cause hazard situations 5 In the case of faults or problems that cannot be resolved using the information contained in this manual contact the Manufacturer s assistance service un un Un un mn STORAGE INSTRUCTIONS AND WARNINGS The manufacturer declines all responsibility for damage and faults to OPTIMO operator functioning caused by non compliance with the storage instructions The operator must be stored in closed dry places at room temperatures of between 20 and 70 C Keep the operator away from sources of heat and naked flames which could damage it and cause malfunctions fires or hazard situations Keep the operator in a horizontal position but not resting on the ground 9 12 un un un un un un un un un m un un un un 11 un Un Un Un un un un un un lt gt 13 SAFETY INSTRUCTIONS AND WARNINGS INDICATIONS AND WARNINGS FOR USE It is the fitter s duty to perform risk analysis and inform the user owner of any existing residual risks Any residual risk detected must be recorded in writing in the operator manual Moving gates usually present the following residual risks impact and crushing against the main closure surface of the leaf or between the leaves impact and crushing in the opening area shearing and dragging between the mobile and fixed guide and support parts during m
11. liance with the information provided in this manual and the safety instructions provided below The Manufacturer declines all responsibility for damage and malfunctions deriving from noncompliance with the maintenance instructions In order to keep the operator efficient and safe follow the cleaning checking and routine maintenance procedures as described in this manual This is the owner s duty Any checking maintenance or repair work must be conducted by a PROFESSIONAL FITTER Always switch off the electricity supply in the event of malfunctions breakdowns and before any other operations in order to avoid the gate from being activated Always disconnect the operator s power supply before performing any maintenance or cleaning operation The owner is not authorised to remove the operator cover as it contains live parts If the power cable is damaged it must be replaced by the Manufacturer or its technical Assistance service or in any case a person with a similar qualification in order to avoid risks Use original spare parts accessories and clamping material only Do not perform technical or programming modifications on the operator Operations of this type may cause malfunctions and or risk of accidents The Manufacturer declines responsibility for damage deriving from modified products In the event of intervention of automatic switches or fuses before restoring function conditions identify and eliminate the fault Request the intervention of
12. n Before installing the operator ensure that the gate is in good mechanical conditions correctly balanced and that it opens and closes correctly Ensure that the risk of entrapment between the open gate and surrounding parts following the opening movement is eliminated Any normally open off buttons installed for the activation of the operator must be positioned so that they are within view of the gate but distant from moving parts Unless said devices operate using keys buttons be positioned at a minimum height of 1 5m and not accessible to unauthorised persons Once the automation has been installed ensure that it is correctly adjusted and that the protection systems and release work properly It is strictly forbidden to motorise a gate that is not already efficient and secure as the automation cannot resolve faults caused by incorrect installation or poor maintenance of the gate During installation make constant reference to harmonised standards EN 12453 and EN12445 Ensure that the individual devices to be installed are suitable for the automation that one intends to create paying careful attention to the points raised in the TECHNICAL DATA chapter Do not proceed if even just one device is unsuitable for the intended use Ensure that the place of installation is not prone to flooding does not contain sources of heat or naked flames fires or hazard situations in general During installation protect automation components to prevent liquids e
13. n del desbloqueo manual podr a causar un movimiento no controlado de la puerta a causa de los da os mec nicos condiciones del balanceamiento mec nico Antes de seguir la maniobra manual sacar la alimentaci n el ctrica No hacer fuerza sobre la llave desbloqueo para evitar romperla Este desbloqueo permite desenganchar la transmisi n del actuador y efectuar el movimiento a mano El desbloqueo se consigue con la llave que deber ser guardada en lugar seguro 360 Desbloqueo lt gt 10 3 0 CONEXIONES Y 8 Antes de proceder a las conexiones leer atentamente lo indicado en cap tulo PRESCRIPCIONES Y ADVERTENCIAS DE SEGURIDAD 8 El actuador debe estar conectado exclusivamente a la central de mando GE UNIR S DL fabricada por LIFE 8 Todas las operaciones de conexi n deben ser efectuadas sin tensi n el ctrica Si el dispositivo de desconexi n no est a la vista poner cartel que diga ATENCION MANTENIMIENTO EN CURSO 8 El cableado interno del actuador electromec nico que han sido hechos en la f brica no ser n modificados 3 1 Conexiones electricas actuador Para acceder al cableado interno mover cobertor 1 desatornillando 2 ver fig A Niegro ABIERTO Azul COMUN Brown CERCA 3 2 Central electronica del actuador La central del mando electr nica utilizada es la GE UNI R DL sea para una o dos hojas 11 lt gt 4 0 GENERAL INFORMATION It is st
14. o avoid deviations during operation In two leaf gates when completely closed the two leaves must meet and match perfectly for their entire height without forcing one against the other or remaining too distant and they must be perfectly vertical Check the opening and closure mechanical end stops they must be suited to the gate leaves and firmly fixed to the ground adequately robust free from potential damage to the gate leaves in the event of collision The operator installation area must not be prone to flooding and therefore it may not be installed too close to the ground The surfaces column pillar wall etc to which the operator s support bracket is fastened must be smooth and vertical parallel to the leaf and sufficiently solid and compact to allow secure fixing Use fixing devices suited to the material of the surface welding for metal tubes or screws and screw anchors for masonry 2 3 4 be well balanced i e they must not move when left in any point during opening or closure Ensure that the leaves not bend or deviate from their course during MAINTENANCE MAINTENANCE INSTRUCTIONS AND WARNINGS Once the automation has been tested the parameters set must NOT be altered If further adjustments e g alterations to the force value are made ALL THE CHECKS REQUIRED FOR TESTING AND COMPLIANCE WITH STANDARDS MUST BE REPEATED The Manufacturer declines responsibility for damage or injury caused by non comp
15. ons ensure that the operations indicated in the MAINTENANCE chapter are performed at the frequency indicated by a PROFESSIONAL FITTER Examine the installation frequently in order to ensure that there are no signs of mechanical unbalance signs of wear and signs of damage to cables and assembled parts do not use automations that require repair work or adjustments Should liquids penetrate inside the operator disconnect the power supply immediately and contact the Manufacturer s Assistance Service the use of the automation in such conditions may cause hazard situations If a problem arises that cannot be resolved using the information contained in this manual contact the Manufacturer s assistance service INSTRUCTIONS AND WARNINGS FOR INSTALLATION Before commencing installation read the SAFETY INSTRUCTIONS AND WARNINGS chapter carefully The COMPETENT PERSON who installs the operator is responsible for performing risk analysis and regulating the automation s safety devices consequentially Before commencing installation check whether further devices or materials are needed to complete the automation in order to suit the specific situation in which it will be used The Fitter must check that the temperature range declared on the operator see TECHNICAL DATA Chap is suited to the place in which the device is installed The operator cannot be fitted on gates with separate pedestrian access unless operator function is prevented when the gate is ope
16. ovement mechanical risks caused bymovement The Manufacturer will not accept responsibility for damage or injury caused by the non observance of the information on use contained in this manual and the failure to observe the safety indications given below The Manufacturer declines responsibility for damage and malfunctions caused by noncompliance with the instructions for use Keep this manual in a safe easily accessible place so that it can be consulted rapidly when necessary Before activating the gate ensure that all persons are at a safe distance Never touch the gate or moving parts when in motion Remain at a safe distance when the gate is in motion only pass when the gate is completely open and immobile Do not allow children to play with gate controls do not leave radio control or other control devices within children s reach Prevent children from playing or standing in the vicinity of the gate or the control organs radio controls the same precautions should be adopted for disabled persons and animals In the event of malfunctions noisiness jerky movements etc suspend the use of the automation immediately failure to observe this rule may entail serious hazards risks of accidents and or serious damage to the gate and the automation Contact a PROFESSIONAL FITTER and in the meantime use the gate manually by disconnecting the operator see the OPERATOR ACTUATOR RELEASE chapter In order to maintain the automation in efficient conditi
17. r and the owner of all rights concerning this document The Manufacturer s information equired by Machinery Directive 98 37 EC is as follows LIFE home integration Via S Pertini 3 5 31014 COLLE UMBERTO TV Italia 39 0438 388 592 39 0438 388 593 www homelife it info homelife it The identity plate bears information on the Manufacturer of the operator and specifies the type and date month year of manufacture For further information on technical or commercial issues and technician call out and spares requests Clients may contact the Manufacturer or area representative from whom the product was purchased INTENDE USE s OPTIMO is a low voltage irreversible articulated mechanical operator designed exclusively for opening and closing one and two leaf residentialtype swing gates only Improper use or use on gates larger than those indicated in the TECHNICAL DATA and USAGE RESTRICTIONS chapters will be considered non conform to the intended use The Manufacturer declines all responsibility for other use The owner accepts full responsibility for improper use which will result in the warranty being rendered void s Any usage differing from that described above is forbidden s The operator may not be installed or used in potentially explosive environments s Motorised gates must conform to current European standards and Directives including EN 12604 and EN 12605 s The operator may only be used when in perfect working order and in
18. refore does not guarantee the safe operation of the automation S Do not proceed with installation connection and trial run in the event of doubts or indecision of any kind S This manual must be read carefully and understood before installing the operator If doubts arise during installation contact a PROFESSIONAL FITTER or the MANUFACTURER S Only mount the operator on gates that are perfectly hinged and well balanced A gate that is not correctly hinged and balanced can cause serious injury to the user and or damage to the operator 5 The Manufacturer declines all responsibility for damage and faults to the operator caused by non observance of the instructions contained in this manual Keep this manual in a safe and easily accessible place so that it can be consulted rapidly when necessary During installation connection trial run and usage of the operator observe all applicable accident prevention and safety regulations In the interests of safety and optimal functioning of the operator only use original spares accessories devices and fastening apparatus Do not perform alterations to any operator device or component This type of operation may cause malfunctions The Manufacturer declines all responsibility for damage caused by products that have been modified The operator should not be used until the setting up procedure described in the STARTING UP chapter has been performed Should liquids penetrate inside the operator disconnect t
19. rictly forbidden to copy or reproduce this instruction manual without written permission to do so and subsequent verification by LIFE home integration Translation into other languages of all or part of the manual is strictly forbidden without previous written authorisation from and subsequent verification by LIFE home integration All rights on this document are reserved LIFE home integration will not accept responsibility for damage or malfunctions caused by incorrect installation or improper use of products and Users are therefore recommended to read this manual carefully LIFE home integration will not accept responsibility for damage or malfunctions caused by the use of the automation together with the devices of other manufacturers such action will render the warranty void LIFE home integration will not accept responsibility for damage or injury caused by non compliance with the installation set up maintenance and use indications contained in this manual and the safety instructions described in the SAFETY INSTRUCTIONS AND WARNINGS chapter With the aim of improving its products LIFE home integration reserves the right to bring about alterations to them at any time without giving prior notice This document conforms to the state of the automation at which it is provided when released for sale INFORMATION ON THE MANUFACTURER LIFE home integration is the manufacturer of the OPTIMO automation and will hereinafter be referred to as manufacture
20. te hembra del visinfin corra perfectamente por l y que con la puerta cerrada o abierta permanezca al menos 5 mmentre el soporte corredizo y los finales de carrera Es necesario usar el agujero diferente sobre el soporte posterior repitiendo las operaciones indicadas en los puntos c y d Definir con precisi n las posiciones de apertura y cierre de las hojas de la puerta regulando las posiciones de las finales de carrera de la siguiente manera S Lievar la puerta a la posici n de cierre al tope mec nico S Atrasar el final carrera de cierre 1 con la llave y ponerlo de modo que toque el soporte corredizo hembra 5 Luego bloquearlo fuertemente con el tornillo sin cabeza 6 S Lievar la hoja de la puerta a la posici n de apertura deseada S Atrasar el final carrera de apertura 2 con la llave y posicionamiento de manera que toque el soporte corredizo hembra 5 luego bloquear apretando el tornillo sin cabeza fuertemente 7 Fijar de modo definitivos el soporte anterior del actuador a la hoja eligiendo los medios necesarios seg n el material de la cancela soldadura o tornillo Bloquear actuador seg n indicado en manual cap tulo DESBLOQUEO ACTUADOR Montar cobertor de nuevo y el de aluminio antes sacados 2 5 Desbloqueo Actuador ATENCION instalador deberfijar permanentemente la etiqueta concerniente a la operaci n de desbloqueo manual cerca de la llave para desbloqueo manual La activaci
Download Pdf Manuals
Related Search