SEFRAM 80 - Amazon Web Services
Contents
1. Se r f rer au manuel TV Courant alternatif Caract ristiques L appareil inclus 2 fonctions test de phase ouverte ordre de phases Cet appareil est l outil id al pour l installation de dispositifs lectrique ou lectrotechnique Autonome de faible encombrement robuste Conforme la norme IEC 1010 Livr avec kit de connexion 4 M thode de mesure Utilisation en testeur d ordre de phase et d absence de phase 1 2 3 Si la lampe R est teinte Brancher les cordons au dispositif contr ler source d nergie moteur Appuyer sur le bouton de test et maintenir enfonc durant tout le temps n cessaire la mesure S assurer que les lampes de pr sence de phase sont toutes allum es Sinon il y a rupture ou absence sur une ou plusieurs phases La phase connect e au cordon rouge est absente Si la lampe S est teinte La phase connect e au cordon blanc est absente Si la lampe T est teinte La phase connect e au cordon noir est absente Si une des lampes est teinte absence d une phase le disque 4 interne ne tourne pas V rification de l ordre des phases Le disque interne indique le sens de rotation des phases Si le disque ne tourne pas dans le sens de la fl che inverser les connexions d un ou deux des fils SI le disque tourne dans le sens indiqu par la fl che2. sens des aiguilles d une montre l ordre des phases est R S T 5 Sp cifications Tension d entr e 200V AC 600V AC max Fr quence 50 60 Hz Circuit de mesure m canique disque tournant Surcharge 1500V AC durant 1 minute maximum i S curit IEC 1010 Cat Ill 600V Dimensions 132 L x 84 1 x 39 H mm Mas 515g Accessoires Cordons de 1 5m avec pinces crocodile rouge jaune et bleu housse de transport manuel d utilisation 6 Maintenance Aucune maintenance n est requise pour cet appareil Nettoyage ATTENTION Afin d viter tout risque de choc lectrique ne jamais exposer le bo tier u lors de l utilisation Nettoyer p riodiquement le bo tier l aide d un chiffon doux et Humide Ne pas utiliser de solvant 1 Introduction NOTE This meter has been designed and tested according to IEC Publication 348 Safety Requirements for Electronic Measuring Apparatus IEC 1001 EN61010 and other safety standards Follow all warnings to ensure safe operation WARNING READ SAFETY NOTES NEXT PAGE BEFORE USING THE METER 8 2 Safety Notes Read the following safety information carefully before attempting to operate or service the meter Use the meter only as specified in this manual otherwise the Protection provided by the meter may be impaired Rated environmental condition 1 Indoor use 2 Installation Category III 3 Pollution Degree 2 4 Alt
3. use abrasives or solvents SEFRAM Instruments et Syst mes 32 Rue Edouard MARTEL F42100 SAINT ETIENNE FRANCE Tel 33 0 4 77 59 36 81 Fax 33 0 4 77 57 23 23 Site WEB www sefram fr e mail sales sefram fr Support technique 33 0 4 77 59 36 96 R f rence M908000F00 13
4. SEFRAM 8 Notice d utilisation Users Manual INDEX FRAN AIS Introduction Prescriptions de s curit Caract ristiques M thode de mesure Sp cifications Maintenance Addresse et contacts ENGLISH Introduction Safety Notes Features Measuring Methods Specifications Contact numbers Technical Support an BrNOAaON eo 1 Introduction Remarque Cet instrument a t con u et test selon les prescriptions de la norme internationale IEC Publication 348 Safety Requirements for Electronic Measuring Apparatus IEC 1001 EN61010 Suivre scrupuleusement les prescriptions de s curit lors de l utilisation ATTENTION Lire les prescriptions de s curit avant toute utilisation 2 Prescriptions de s curit Lire ces prescriptions avant toute utilisation de l appareil N utiliser l appareil que dans les limites sp cifi es En dehors des limites l appareil pourrait tre endommag et la s curit de l utilisateur non garantie Conditions d utilisation 4 Utilisation l int rieur 2 Cat gorie d installation CAT III 600V 3 Degr de pollution 2 4 Altitude d utilisation 2000 m tres maximum 5 Humidit relative 80 Max 6 Temp rature d utilisation 0 C 40 C 7 Temp rature de stockage 10 C 60 C Les symboles suivant sont utilis s sur l appareil Double isolement A Danger Risque de choc lectrique A Attention
5. goes off Make sure that all of the three lamps for open phase check are on Ifso there is no open phase When any of the three lamps is not on there is open phase Open phase check Open phase on lamp R is not on terminal where Red alligator clip is Connected Open phase check Open phase on lamp S is not on terminal where White alligator clip is Connected Open phase check Open phase on lamp T is not on terminal where 2 Black alligator clip is connected When the open phase check lamps are not on the rotating disc does not turn Check the rotating direction of the inside disc through the phase sequence indication window 1 When the rotating disc turns counter clockwise alternate the Connection of the two of the three alligator clips Then the rotating disc will turn clockwise 2 When the rotating disc tums clockwise phase sequence is R S and T in order of the power source terminals where the Red White and Black alligator clips are connected 11 5 Specifications Input Voltage 200V AC up to 600V AC max Frequency Range 50 60 Hz Withstand Voltage 1 500V AC for one minute Dimension 132 x 84 x 39 mm Weight Approximately 515g Cord 1 5m each of Red R White S and Black T cord Cleaning and Storage WARNING To avoid electrical shock or damage to the meter do not get water inside the case Periodically wipe the case with a damp cloth and detergent do not
6. itude up to 2000 Meter 5 Relative Humidity 80 Max 6 Ambient Temperature 0 40 C Observe the International Electrical Symbols listed below Meter is protected throughout by double insulation or reinforced insulation A Warming Risk of electric shock A Caution Refer to this manual before using the i meter av Alternating current Features Two functions in one unit The model is designed to check phase sequence Lamps provided on the unit will also tell you whether phase is open or which phase is open at a glance Large size alligator clips Can easily hold terminals of switchboards Highly reliable Can check a wide range of 3 phase power source from 200V to 600V Sealed against dust the unit ensures highly dependable and trouble free performance Functional design Small lightweight and portable Designed for maximum ease of operation and ruggedness throughout Safety design No exposed metal parts Safety features are incorporated throughout including minimize damage due to negligence 10 4 Measuring Methods Connect color coded alligator Clips to the terminals of a 3 phase power Source where a rotating electrical machine such as a motor will be connected Connecting order may be optional Press the push switch button located on top of the unit Keep this button pressed during phase sequence or open phase check When the push switch button is released it immediately
Download Pdf Manuals
Related Search