チタニウム触媒ストレートパイプ GENESIS COUPE 200 TURBO
Contents
1. 1 A 1 2 2 TOMEI gt 49 69N m 5 0 7 0kgf m 1 49 69N2. A A KIT CONTENTS Below is the contents of this kit with the quantity listed in brackets Decat Straight Pipe 1 Gaskets 2 i3 jonn Flange Bolt Nut M12x P 1 25 4 Washer 4 M12x P 1 25 4 1 BOLT SMOOTH PASTE PREME EXPREME Sticker 2 Bolt Smooth Paste 1 REQUIRED TOOLS These tools are the bare min
3. m 5 0 7 0kgf m 49 69N m 5 0 7 0kgf m 2 A 1 2 2500rpm 3 A
4. QTOME I 10 5 M19Y650 The Engine Specialist E 62 BA INSTALLATION MANUAL EXPREME 7 GENESIS COUPE 200 TURBO EXPREME Ti Titanium CAT Straight Pipe for GENESIS COUPE 200 TURBO 431002 PART NUMBER GENESIS COUPE 200 TURBO APPLICATION kkk p English 5pD TOMEI TOMEI Please carefully read this manual prior to installation Please also refer to the Hyundai Service Manual with this Manual After the installation has been completed please keep this manual for future reference If the install was done in a shop please make sure to give this manual to the owner Thank you for purchasing another quality TOMEI product This TOMEI Titanium Exhaust Straight Pipe has been d
5. esigned for true competition use to maximize weight reduction and exhaust flow efficiency 1 2 M12xP 1 25 4 M12xP 1 25 4 M2 PREME EXPREME 2 1 A nl SA
6. imum required for the job General Engine Maintenance Tools Torque Wrench Service Manual A CAUTION E This product is designed to be used for off road competition purposes only E This product is to be installed by a qualified professional in a fully equipped workshop E This product was designed specifically for the application specified If the attempt was made to use this product on another engine car other than specified then you will risk damaging this kit and or the engine or components related with it E This product is to be installed with the appropriate tools and equipment to prevent any engine failures and injuries or bodily harm A WARNING E This product is to be installed when the engine and engine bay is cold E Please be sure that all parts are fitted correctly to avoid any possible fire risk hazards 1 REMOVAL OF THE STOCK CATALYTIC CONVERTER A This manual only provides the simple instructions For more details please refer to the vehicles official service manual 1 Disconnect the cars battery negative terminal 2 Remove the stock catalytic converter 2 TOMEI STRAIGHT PIPE INSTALLATION Illustration of the mounting position of each bolt amp gasket The installation of the bolts included in the kit is shown below m lt Torque settings for the kit contents gt Gasket Flange Bolt Nut 49 69N m 5 0 7 0kgf m Use the bolt smooth paste provided to prevent the bolts from se
7. ized Tomei Powered distributor OPEN Monday Friday National holidays and public holidays excluded 09 00 18 00 GENESIS COUPE 200 TURBO 10 5 M19Y650 TITANIUM STRAIGHT PIPE GENESIS COUPE 200 TURBO INSTALLATION MANUAL 10 May M19Y650
8. izures and rust welds MOUNTING INSTRUCTIONS 1 Install the straight Each gasket bolt and nut using the supplied straight pipe catalyst installed FRONT EXHAUST PIPE Use the Supplied Gasket Ref Torque Settings Nut Ref 49 69N m 5 0 7 0kgf m CENTER EXHAUST PIPE Use the supplied Gasket Ref 1 Torque Settings Nut Ref 49 69N m 5 0 7 0kgf m 2 Reconnect the cars battery negative terminal Z cAUTION Please check all clearances with the vehicles body and make sure that the bolts are not interfering with anything else The clearances can change from vehicle to vehicle Be sure that all the bolts are tightened correctly so that there is no pollution caused form any exhaust leaks After fitting the straight pipe and or catalytic converter please check that there are no signs of oil dirt so as not to burn bake it later when the car is running TIP clean all fingerprints and oil off the Titanium exhaust before starting the engine INSTALLATION VERIFICATION 1 Check again the vehicle that there are no parts interfering with any other components 2 Start the engine and let it idle first before taking it up to 2500 RPM to check and listen for any signs of exhaust leaks or any abnormal sounds Then recheck the car again for any loose parts or gas leaks 3 After the initial test drive check the car again for any signs of exhaust gas leakage and any loose parts bolts and nuts A WARNING An
9. y interference with any parts components can pose a fire risk hazard so please meticulously check the car after the install Any exhaust leaks can decrease performance efficiency and also pose a health risk hazard with toxic exhaust gas poisoning If there is anything felt abnormal when driving please stop immediately and check the car over When any work or checks are to be done with the metal exhaust components then please do so when it is cold to prevent any burns and injuries If any parts are lost or have fallen off then does not restart the car until the missing part s can be replaced properly caUuTION The vehicles characteristics and exhaust backpressure may change after installing this product so after the install you may need to have the ECU map settings and fuel supply pressure checked and adjust accordingly to suit the new setup TOME POWERED wc At Bit RENT K 7194 0004 1737 3 TEL 042 795 8411 FAX 042 799 7851 1737 3 Tsuruma Machida shi Tokyo 194 0004 JAPAN TEL 81 42 795 841 1 main switchboard FAX 81 42 799 7851 http www tomei p co jp 9 00 18 00 If you have any questions in regards to the installation of this product please contact your local author
Download Pdf Manuals
Related Search