取扱説明書
Contents
1. HTC OFF OFF2. 2 nf Screw i in Air hose blue white Overhose gray 9 UHT ORP About This Product This is an air micro grinder with a plastic body for grinding and polishing metal and stone Offers various types of processing by exchanging the 3 mm shank abrasives This is a rotating tool Strictly observe the warnings and instructions on this manual for safe use Connection Connecting the Air Hose Connect the air hose blue white to the nipple on the tool body Screw in the hose band that is threaded inside to clamp the hose After clamping connect the overhose to the tool F On the opposite side of the air hose attach the quick joint in the same manner I 2N 1 MM uo POINT Pass the a
3. To use the tool connect it to the air supply with the specified air pressure and flow volume Turn the control valve counterclockwise The valve opens fully by 2 turns Adjust the flow volume by this valve to control the rotation speed of the tool Adjust the air pressure to 0 5 MPa by the air regulator in the FRL unit com6ressor To stop using the tool turn the control valve clockwise fully and confirm that rotation stops Be sure to disconnect the tool from the air supply after use Prevent dust or chip from getting in from the quick joint for storage Replacing the Accessories Insert the pin into the pin hole to fix the tool shaft Loosen the collet nut by the attached wrench Remove the accessory and replace with a new one Secure the replaced accessory in reverse Order to removal Check that the accessory is secured and remove the pin Do not tighten the nut without the accessory inside Be sure to attach the accesory of the correct size before tightening the
4. EE Ai EE 3 6 DS UHT UHT
5. Y Orignal Instructions UA ts Safety Precautions Symbols for Safe Use The symbols below alert you to risk in using the product and give precautions Be sure to observe all the precautions for safe use Failure to observe the precautions may result in serious risk to your health and may lead to death in some cases N WARNING Failure to observe the precautions may result in risk to your health and may lead to accidents injury or blindness It may result in damage to the product A CAUTION A WARNING Wma Using the tool involves danger give the highest priority to safety Do not touch the rotating tip of the tool Use leather protective gloves not cotton work gloves Do not attempt to alter the tool and accessories Turn off the valve of the tool before stopping the work Do not leave the tool rotating Do not exceed the maximum numbers of rotations of accessories Do not use damaged cracked warped or fallen tools and accessories Confirm that the valve is off before connecting the joint Never use the tool near inflammable gases liquids or substances A C AU TION EE Be sure
6. UHT E es U Light WAS collet nut The collet may bend and the accessory ca
7. 0 470 0168 446 268 TEL 0561 38 2101 FAX 056 1 38 2108 LL lt 446 268 Shimokagamida Haruki Togo cho Aichi gun Aichi Japan 470 0162 TEL 81 561 38 2101 FAX 81 561 38 2108 UHT CORPORATION
8. to use the FRL unit air filter air regulator and lubricator to remove dust and moisture from the supply air and to keep supplying oil Recommended oil supply 3 5 drops min This tool involves vibration do not use it continuously to prevent tendovaginitis and vibration white fnger Wear protective glasses hat mask ear muffs and gloves when using the tool Do not use the tool exceeding the specified air pressure Be sure to make a trial run before operation Check the collet chuck for wear and damage before use Stop using the tool if you notice abnormal noise heat or vibration Be sure to cut off the primary air supply and remove residual air before disconnecting the quick joint from the alr pressure SOUTCe Use the UHT s genuine or recommended accessories with the correct sizes and follow the appropriate instructions and regulations for use 3mm lt Hose band white
9. ir hose through the hose bands beforehand Ru gt Pass the air hose through the overhose beforehand in RE the same manner 5 Connect to the air source ON OFF 3 ISO VG32 3 Filter Regulator Lubricator Operation Procedure ON OFF In connecting air be sure to use the FRL unit sold separately to remove dust and moisture from the supply air and to keep Iubricating Industrial multipurpose oil with viscosity of ISO VG32 is recommended Using the tool without the FRL unit may result in extremely shortened service life performance degrada
10. nnot be inserted The warranty does NOT cover such defects Ifitis unavoidable to use accessories not made by UHT note the following Do not exceed the maximum rotation speed of the accessory Do not use the carbide bur with a blade diameter larger than the shank diameter ES lt may damage the tool body accessories and workpiece materials The warranty does NOT cover such defects For warranty repair and paid repair contact your local dealer or UHT EC DECLARATION OF CONFORMITY for Grinders ULight Manufactured By UHT Corporation 446 268 Simokagamida Haruki To go cho Aichi gun Aichi Japan 470 0162 Standards used as uidance Machinery Directive EN12100 2010 Means of Conformiy The Product is in conformity with Machinery Directive 2006 42 EC Date a
11. tion and heat The warranty does NOT cover defect resulting from neglecting this instruction 3 0 5MPa 3 FRL unit MP SSM gt
Download Pdf Manuals
Related Search