Samsung TRIUMPH Washer with Slim Space Saving, 6.5 kg User Manual
Contents
1. 1 Loosen the leg bolt by turning it with your hand until itis at the desired height 2 Tighten the locking nut by turning it with the wrench Place the washer on a sturdy flat surface dx If the washer is placed on an uneven or weak surface noise or vibration occurs Only a 1 degrees angle is allowed Installing the Washing Machine Removing the shipping bolts Before using the washing machine you must remove all of the shipping bolts from the back of the unit To remove the bolts 1 Loosen all bolts with the wrench before removing them 2 Take each bolt head and pull it through the wide part of the hole Repeat for each bolt 3 Fill the holes with the supplied plastic covers 4 Keep the shipping bolts for future use Connecting the water supply hose AS e eon The water supply hose must be connected to the washing machine at one end and to the water faucet at the other Do not stretch the water supply hose If the hose is too short and you do not wish to move the water faucet replace the hose with a longer high pressure hose To connect the water supply hose 1 Take the L shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine Tighten by hand 2 Connect the other end of the cold water supply hose to your sink s cold water faucet and tighten it by hand If necessary you can reposition the water supply ho2. The wires in this mains lead are coloured in accordance with the following code Green and yellow Earth Blue Neutral Brown Live AS the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug proceed as follows Connect the green and yellow wire to the terminal in the plug marked with the letter E or the earth symbol or coloured green or green and yellow Connect the blue wire to the terminal marked with the letter N or coloured black Connect the brown wire to the terminal marked with the letter L or coloured red Consult a qualified electrician or service technician if in doubt about any of these instructions The manufacturer of this washing machine will not accept any liability for damage to persons or material for non observance of these requirements There are no user serviceable parts inside the washing machine and if the mains lead of this appliance is damaged it must only be replaced by qualified service personnel approved by the manufacturer because special tools are required GREEN AND YELLOW 13 AMP FUSE BLUE BROWN WARNING Ensure that the plug and power cord are not damaged before use If you have any reason to remove the moulded plug from this appliance immediately remove the fuse and dispose of the plug Do not connect the plug to a mains socket under any circ
3. Washing Machine Owner s Instructions WF J1461 V S C J1261 V S C d i using the appliance J1061 V S C J861 V S C Safety Instructiolis cuc s Re ue EUR Ru eek eas 2 WF B1461 V S C B1261 V S C Installing the Washing Machine 3 B1061 V S C 861 V S C Unpacking the Washing Machine 3 T Overview of the washing machine 3 WF R1261 V S Q R1061 VS C Selecting a location 2 4 s 4454 Ier pr ere ey 3 Adjusting the leveling feet 3 R861 V S C Removing the shipping 4 WF F1261 V S C F1061 V S C Connecting the water supply hose 4 Positioning the drain 4 F861 V S C Plugging inthe machine 0 000 ee ee eee 5 WF S1061 V S Q 5861 W S C Washing Load of Laundry 6 Overview of the 6 Washing for the firsttime 2 2 0 0 00 e eee ee eee 7 Putting detergent in the washing machine 7 Washing clothes 7 Selecting OPTIONS pos die ROW Ausland Sia acetals 8 Washing tips and DINES so esias soa od ma at atla ira eee eee 8 Maintaining
4. R1061 R861 F1261 F1061 F861 51061 5861 230 700w 360w 320w 270w 580W 530w soow 430W ssow soow 430W 270w 230w 180w 250w 200w PUMPING 34W MODEL WF J1461 71261 71061 861 cd 61 Wk po WF F1261 F1061 F861 WE S1061 5861 PACKAGE Wt 25kg 25 21kg 19kg 18kg PLASTIC 1 0kg 1 0kg 0 9 kg 0 8 kg 0 8 kg WE J1261 B1261 R1261 WF J1061 81061 R1061 seiNBEVO MODEL WEF J1461 81461 dus WE J861 8861 R861 F861 S861 LUTION rpm 1400 1200 1000 800 7 Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center U A E 800SAMSUNG 7267864 www samsung com mea
5. the Washing 9 Repairing a frozen washing machine 9 Cleaning the 9 Cleaning the debris 9 DUO Cleaning the water hose mesh 9 b 10 A Problems and solutions sises lees 10 Understanding error messages 10 1 Programme 11 Appendix celer 12 Fabriccarechart 2 cca cb eee eee or eem 12 Electrical warnings 2s xum eU ee ES 12 Protecting the 12 Declaration of conformity 12 Specification siu a beg RP pu e op ORA 13 Register your product at www samsung com global register CODE NO DC68 02350E EN Safety Precautions Congratulations on your purchase of this Samsung washing machine These Owner s Instructions contain valuable information on the installation use and care of this appliance Please take the time to read these instructions so that you can take full advantage of the washing machine s features and enjoy this appliance for many years to come Before using the appliance Packing materials can be dangerous to children keep all packing material plastic bags polystyrene etc well out of the
6. washing machine surfaces including the control panel with a soft cloth and non abrasive household detergents Use a soft cloth to dry the surfaces Do not pour water on the washing machine Remove the base cover from the front of the washing machine Unscrew the filter cap and take it out Wash any dirt or other material from the filter Make sure the drain pump propeller behind the filter is not blocked Replace the filter cap Replace the base cover y M Cleaning the water hose mesh filter You should clean the water hose mesh filter at least one time per year or when the lamps on your machine flickers To do this 1 Turn off the water source to the washing machine 2 Unscrew the hose from the back of the washing machine lel 3 With a pair of pliers gently pull out the mesh filter from the end of the gt hose and rinse it under water until clean Aa Also clean the inside and outside of the threaded connector 9 4 Push the filter back into place Screw the hose back onto the washing machine Turn on the faucet and make sure the connections are watertight Troubleshooting Problems and solutions The washing machine will not start Make sure the door is firmly closed Make sure the washing machine is plugged in Make sure the water source faucet is turned Make sure to press the Start Pause button No water or insufficient wa
7. 1061 B861 R1061 R861 F1061 F861 Cotton 8 0 kg 6 5 kg 5 2 kg 4 5 kg 3 5 kg Colour 8 0 kg 6 5 kg 5 2 kg 4 5 kg 3 5 kg Synthetics 3 0 kg 3 0 kg 2 5 kg 2 5 kg 2 0 kg Wool 2 0 kg 2 0 kg 1 5 kg 1 5 kg 1 0 kg Detergent tips The type of detergent you should use is based on the type of fabric Cotton Synthetic Wool items colour wash temperature degree and type of soiling Always use low suds laundry soap which is designed for automatic washing machines When determining the detergent quantity it s necessary to consider recommendations of the detergent manufacturer indicated on the package as well as weight type of laundry it s fouling factor and water hardness in your region Note Keep detergents and additives in a safe dry place out of the reach of children Maintaining the Washing Machine Repairing a frozen washing machine If the temperature drops below freezing and your washing machine is frozen 1 Unplug the washing machine 2 Pour warm water on the source faucet to loosen the water supply hose 3 4 5 Remove the water supply hose and soak it in warm water Pour warm water into the washing machine drum and let it sit for 10 minutes Reconnect the water supply hose to the water faucet and check if the water supply and drain operations are normal Cleaning the exterior T 2 Cleaning the debris filter Clean the debris filter 2 or 3 times a year Ti 2 3 4 Wipe the
8. Averagely or lightly soiled cottons bed linen table linen underwear towels shirts etc Colour Averagely or lightly soiled cottons bed linen table linen underwear towels shirts etc Synthetic Lightly or averagely soiled blouses shirts etc Made of polyester Diolen Trevira polyamide perlon Nylon or similar blends Handwash Very light wash course like hand wash Wool Only machine washable wollens with pure new wool label Quick Lightly soiled cottons or linen blouses shirts dark coloured terry cloth coloured linen articles jeans etc 1 The programme duration data has been measured under the conditions specified in Standard IEC 456 2 Consumption in individual homes may differ from the values given in the table due to variations in the pressure and temperature of the water supply the load and the type of laundry Appendix Fabric care chart Resistant material Can be ironed at 100 C max C7 Delicate fabric Item may be washed at 95 C Item may be washed at 60 C Item may be washed at 40 C Item may be washed at 30 C Do not iron Can be dry cleaned using any solvent Dry clean with perchloride lighter fuel pure alcohol or R113 only Dry clean with aviation fuel pure alcohol or R113 only Do not dry clean Item may be hand washed Dry flat Dry clean only Can be hung to dry HEY Dry on clothes hanger Do not bleach Tumble dry normal heat 2 NI Can be ironed
9. Prewash is only available when washing cotton synthetic or Colour 6 Delay Start selection button Press this button repeatedly to rotate between the retarded start options available from 3 Hours to 24 Hours in 1 hour increments 7 Start Pause button Press to pause and restart programs On Off button Press once to turn the washing machine on press again to turn the washing machine off If the washing machine power is left on for longer than 10 minutes without any buttons being touched the power automatically turns off What is the Child Lock function Ifyou press the Child Lock button Spint Option button longer than 2 sec during operation this function is selected If once this function is selected no change can be done until the end of laundry Press the Child Lock button Spin Option button longer than 2 sec to cancel the function M o Washing a Load of Laundry WM stops the current step of the cycle or does not proceed to the next step of washing indication of remain time on LED display may increase Your new washing machine is equipped with Fuzzy Logic system which not only sets the optimum level of water and other parameters of washing but also controls the washing process as well as makes necessary corrections in order to provide better washing results In the above mentioned matter the Fuzzy Logic system has detected deviations in washing cycle such as high quantity of detergent
10. at 200 C max vd A Can be bleached in cold water A EA Tumble dry reduced heat KA fx Can be ironed at 150 C max Do not tumble dry R Electrical warnings To reduce the risk of fire electrical shock and other injuries keep these safety precautions in mind Operate the appliance only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your appliance dealer or local power company Use only a grounded or polarized outlet This plug will fit into the power outlet only one way If you are unable to insert the plug fully into the outlet try reversing the plug If the plug still doesn t fit contact your electrician to replace your outlet Protect the power cord Power supply cords should be routed so that they are unlikely to be walked on or pinched by items placed on or against them Pay particular attention to cords at plugs convenience receptacles and the point where they exit from the unit Do not overload the wall outlet or extension cords Overloading can result in fire or electric shock Protecting the environment This appliance is manufactured from recyclable materials If you decide to dispose of this appliance please observe local waste disposal regulations Cut off the power cord so that the appliance cannot be connected to a power source Remove the door so that animals and small children cannot get trapped inside the appliance Do n
11. at the end of the cycle high vibration level while spinning etc You can adjust existing wash programs i e change wash temperature and spin speed After detection of such abnormalities the washing machine is suspending the normal course of program in order to normalize these parameters and continue the cycle Fuzzy logic system makes 7 attempts to eliminate such deviations If it is impossible to normalize the above mentioned deviations by Fuzzy Logic system you will see the corresponding indication on LED lamps see chapter Troubleshooting The operation of Washing machine that corresponds to above mentioned scheme is considered to be normal Washing for the first time Before washing clothes for the first time you must run a complete cycle without clothes To do this Press the On Off button Pour a little detergent in the detergent drawer D Turn on the water supply to the washing machine Press the Temperature button repeatedly until 40 C is displayed Press the Start Pause button This will remove any water from the manufacturer s test run remaining in the machine vd OM TR Putting detergent in the washing machine 1 Pull out the detergent drawer 2 Add laundry detergent into compartment 3 Add softener into compartment if you desire 4 Add prewash detergent into compartment D if you desire Washing clothes manually You can wash clothes manually without using the Fuzzy Logic feat
12. der no circumstances use a metal brush For washing machines with ventilation openings in the base that a carpet must not obstruct the openings Use the new hose sets and old hose sets should not be reused SAVE THESE INSTRUCTION Installing the Washing Machine Unpacking the Washing Machine Unpack your washing machine and inspect it for shipping damage Also make sure that you have received all of the items shown below If the washing machine was damaged during shipping or you do not have all of the items contact your Samsung dealer immediately Overview of the washing machine Cover top Control panel Detergent drawer Door Cold Water supply hose o Debris filter Oo k Bolt hole covers Base cover e em Adjustable feet E dm Selecting a location Before you install the washing machine select a location with the following characteristics Ahard level surface if the surface is uneven see Adjusting the leveling feet below Away from direct sunlight Adequate ventilation Room temperature that will not fall below 0 C Away from sources of heat such as coal or gas Make sure that the washing machine does not stand on its power cord Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor Adjusting the leveling feet If the floor is uneven adjust the feet do not insert pieces of wood or any other objects under the feet
13. liance necessary If the plug power supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard This appliance should only be serviced by an authorized service center and only genuine spare parts should be used This appliance is not intended for use by young children or infirm persons unless theyhave been adequately supervised by a responsible person to ensure that they can use the appliance safely Young children should be supervised to ensure that they do not play with the appliance This appliance has to be connected to the plug endurable to proper power consumption This appliance has to be positioned so that the plug is accessible after installation Donot use processed water containing oil cream or lotion which is usually found in skin care shops or massage clinics Otherwise this will cause the packing to be deformed which causes a malfunction or water leak Astainless washing tube does not usually rust However if some metal such as a hair pin is left in the tube for an extended time the tube could rust Donotleave water or bleach containing chlorine in the tube for an extended period of time Donotregularly use or leave water containing iron in the tube for an extended period of time If rust starts appearing on the surface of the tube apply a cleansing agent neutral to the surface and use a sponge or soft cloth to clean it Un
14. ot exceed the detergent quantities recommended in the detergent manu facturers instructions Use stain removal products and bleaches before the wash cycle only when strictly necessary Save water and electricity by only washing full loads the exact amount depends upon the program used Declaration of conformity This appliance complies with European safety standards EC directive 93 68 and EN Standard 60335 Appendix Specification TYPE FRONT LOADING WASHER WE I1461 71261 71061 861 WF B1461 81261 81061 8861 WF R1261 R1061 R861 WF F1261 F1061 F861 WF S1061 5861 DIMENSION W598mm X W598mm X D600mm X H844mm W598mm X D550mm X W598mm X D450mm W598mm X D404mm D340mm X H844mm XH844mm XH844mm H 844mm WATER PRESSURE 50 kPa 800 kPa WATER VOLUME 601 541 491 481 431 NET WEIGHT 75 kg 75 kg 66 kg 62 kg 58 kg WASH AND SPIN CAPAC 8 kg DRY LAUNDRY 6 5 kg DRY LAUNDRY 5 2kg DRYLAUNDRY 4 5kg DRYLAUNDRY 25908 ITY MODEL WE 1461 71261 1061 861 a WE o d WE F1261 F1061 E861 WF S1061 5861 WASHING 2201 2000W 220V 200w 220V 1900W 22v 1800W 220v 1800W AND POWER HEATING 240V 2400W 240V 240V zoow 240V zoow 240V 2100W CONSUMP TION wove WE WE we wee we we WE we we we we we WE we we PiN J1461 J1261 J1061 J861 B1461 B1261 B1061 B861 R1261
15. panel 4 Press Start Pause to begin the cycle Rinse Your machine will run through an additional rinsing cycle The washing duration will be prolonged accordingly Rinse Hold The laundry remains soaking in the final rinse water Before the laundry can be unloaded the Spin program must be run Washing tips and hints Sorting your laundry Sort your laundry according to the following characteristics of fabric care label symbol Sort laundry into cottons mixed fibers synthetics silks wools and rayon Colour Divide whites and colours Wash new coloured items separately Size Placing items of different sizes in the same load will improve the washing action Sensitivity Wash delicate items separately using the Wool wash program for pure new wool curtains and silk articles Check the labels on the items you are washing or refer to the fabric care chart in the appendix Emptying pockets Coins safety pins and similar items can damage linen the washing machine drum and the water tank Securing fasteners Close zippers and fasten buttons or hooks loose belts or ribbons should be tied together Determining load capacity Do not overload the washing machine or your laundry may not wash properly Use the chart below to determine the load capacity for the type of laundry you are washing Load Capacity Fabfic Type WF J1461 J1261 WF B1461 B1261 WF R1261 WF F1261 WF S1061 F861 J1061 J861 B
16. reach of children The appliance is designed for home use only Make sure that water and electrical connections are made by qualified technicians observing the manufacturer s instructions see Installing the Washing Machine and local safety regulations All packaging and shipping bolts must be removed before the appliance is used Serious damage may occur if they are not removed See Removing the shipping bolts Before washing clothes for the first time you must run a complete cycle without clothes See Washing for the first time Safety instructions Before cleaning or carrying out maintenance unplug the appliance from the electrical outlet or set the On Off button to Off Make sure that the pockets of all clothing to be washed are empty Hard sharp objects such as coins safety pins nails screws or stones can cause extensive damage to the appliance Always unplug the appliance and turn off the water after use Before you open the door of the appliance check that the water has drained Do not open the door if you can still see water Pets and small children may climb into the appliance Check the appliance before each use glass door becomes very hot during the washing cycle Keep children away from the appliance while it is in use Do not attempt to repair the appliance yourself Repairs made by inexperienced or unqualified persons may cause injury and or make more serious repairs to the app
17. se at the washing machine end by loosening the fitting rotating the hose and retightening the fitting Positioning the drain hose The end of the drain hose may be positioned in three ways Over the edge of a sink The drain hose must be placed at a height of between 60 and 90 cm To keep the drain hose spout bent use the supplied plastic hose guide Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving In a sink drain pipe branch The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground In a drain pipe Samsung recommends that you use a 65 cm high vertical pipe it must be no shorter than 60 cm and no longer than 90 cm Installing the Washing Machine Plugging in the machine You MUST ground the plug of the washing machine Check with a licensed electrician before using the machine to make sure it is properly grounded For U K Users Wiring Instructions WARNING THIS APPLIANCE MUST BE EARTHED This appliance must be earthed In the event of an electrical short circuit earthing reduces the risk of electric shock providing an escape wire for the electric current The appliance is equipped with a mains lead which includes an earth wire for connecting to the earth terminal of your mains plug The plug must be plugged into a socket that is properly installed and earthed
18. ter supply Make sure the water source faucet is turned on Make sure the water source hose is not frozen Make sure the water intake hose is not bent Make sure the filter on the water intake hose is not clogged Detergent remains in the detergent drawer after the wash program is complete Make sure the washing machine is running with sufficient water pressure Put the detergents in the inner parts of the detergent drawer away from the outside edges Washing machine vibrates or is too noisy Make sure the washing machine is set on a level surface If the surface is not level adjust the washing machine feet to level the appliance Make sure that the shipping bolts are removed Make sure the washing machine is not touching any other object e Make sure the laundry load is balanced The washing machine does not drain and or spin Make sure the drain hose is not squashed or bent Make sure the water hose mesh filter is not clogged Understanding error messages Error displayed Solution dE Close the door 4E Make sure the source water faucet is turned on Check the water pressure 5E Clean the debris filter Make sure the drainage hose is installed correctly UE Laundry load is unbalanced loosen any tangled laundry If only one item of clothing needs washing such as a bathrobe or jeans the final spin result might be unsatisfactory and an UE error message will be shown in
19. the display window LE Check the end of the drain hose is too low Make sure the holder of drain hose in the back is intact Check the end of the drain hose is submerged in water Before contacting After Sales service 1 Try to remedy the problem See Troubleshooting on this page 2 Restart the programme to see if the fault is repeated 3 If the malfunction persists call after sales service and describe the problem Programme Chart user option m Spin Speed Max load kg Detergent And Additives MAX rpm T _ _ WF WF Cyde PROGRAM pigen gas WE WE owe wp grey DI0SV 1861 sam Time R1261 F1261 Pre Soft B1061 B861 UI min J1261 B1261 1061 Wash J1461 B1261 R1061 F1061 wash ener R1061 R861 J1061 B1061 861 B1461 R1261 J861 Bggi R861 F861 1261 F1061 F861 1061 861 Cotton 8 0 6 5 5 2 45 3 5 yes 95 1400 1200 1000 800 126 Colour 8 0 6 5 5 2 45 3 5 yes 60 1400 1200 1000 800 98 Synthetics 3 0 3 0 2 5 2 5 2 0 yes 60 800 800 800 x 73 Wool 2 0 2 0 15 15 1 0 yes 40 400 400 400 400 x 42 Handwash 2 0 2 0 15 15 1 0 yes 40 400 400 400 400 x 37 Quick 3 0 3 0 2 0 2 0 1 5 60 1400 1200 1000 800 28 Type of WASH Cotton
20. umstances as there is a danger of electric shock CIRCUITS Your washing machine should be operated on a separate circuit from other appliances Failure to do this may cause the circuit breaker to trip or the fuse to blow Washing a Load of Laundry Overview of the control panel og Option Delay Start emer X This is a general manual The INLAY system may be different from that of the product you purchased For see item 5 below to select the right specifications that match your product Display panel Displays wash cycle and error messages During execution of the program the program indicator blinks Program Select button Press the button repeatedly to select one of the six available wash program Cotton gt Colour gt Synthetics gt Handwash Wool gt Quick gt Rinse Spin gt Spin 3 Temperature selection button Press the button repeatedly to cycle through the available water temperature options cold wash 30 C 40 C 60 C and 95 C When pressing this button during washing you can see the selected temperature in the display panel 4 Spin selection button Press the button repeatedly to cycle through the available spin speed options 5 Option button Press the button repeatedly to cycle through the available partial wash options Rinse Hold gt Rinse gt Rinse Hold Rinse gt Prewash gt Prewash Rinse Hold gt Prewash Rinse gt Prewash Rinse Hold Rinse Note
21. ure To do so Turn on the water at the water source sink Press the On Off button on the washing machine Open the door Load the articles one at a time loosely into the drum without overfilling Close the door Put the detergent in the detergent drawer Repeatedly press the Program button to select the cycle you prefer Cotton Colour Synthetics and Quick 8 Press the Spin button to select the spin speed No Spin 400 800 No Spin 9 Repeatedly press the Option button to select the cycle you prefer Prewash Rinse Rinse hold 10 Press the Temperature button to select the temperature cold wash 30 C 40 C 60 C 95 C 11 Press the Start Pause button and the machine will begin the cycle When the cycle is finished 1 Open the door Note The door will not open until 3 minutes after the machine stops or the power turns off 2 Remove laundry Note The Slow rotation of drum is not fail of the machine after the last spin of Cotton Colour or Quick course That is a function to remove laundry easily cs Washing a Load of Laundry Selecting options Prewash Prewash is only available when washing cotton colour synthetics delicate clothes To use prewash 1 Load the prewash detergent into compartment of the detergent drawer 2 Select Cotton Colour or Synthetic with the Program select button 3 Press the Option button until the Prewash indicator lights up on the control
Download Pdf Manuals
Related Search