Home

Samsung AQV09YWBAN User Manual

1. This check mark requires checking the indoor outdoor unit periodically Follow the description to maintain the air conditioner properly 1 The described operations should be performed more frequently if the area of installation is very dusty NOTE 2 These operations must always be performed by qualified personnel For more detailed information see the installation part in the manual 21 Panama AQVO9Y _IB amp IM_32445A E indd 21 2011 1 19 16 22 59 Mo ea LUE Troubleshooting Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does Check power status and then operate the air conditioner again not work at all lt Plug in or switch on the circuit breaker and then operate the air conditioner again e Check if you have set the Off Timer Operate the air conditioner again by pressing the Power button The temperature e Check if you have selected Dry Fan Turbo d light Cool mode In these modes desired adjustment is not working temperature is set to auto and you cannot adjust the temperature Cool Warm air does not come out of the air Check if the set temperature is higher during Cool mode lower during Heat mode than the current temperature Press the Temp hr or button on the remote controller to conditioner change the set temperature e Check if the Full HD filter is blo
2. up and down Display good sleep indicator na OM wW 2 A Remote controller receiver ee LI TH Timer indicator d light Cool indicator Panama AQVO9Y _IB amp IM_32445A_E indd 7 2011 1 19 16 22 31 SCL j i Checking the remote controller Point the remote controller towards the remote controller receiver of the indoor unit When you properly press the button on the remote controller you will hear beep sound from the indoor unit and a transmit indicator A appears on the remote controller display Remote controller buttons 3K Before using the functions of the remote controller you should set the current time Refer to p 14 Remote controller display Power 1 Turn on off the air conditioner Mode Set one of the 5 operating modes see pages 10 11 for instructions Quiet Reduce noise generated from an indoor unit during operation SPi Set the SPi function on off Smart Saver Less energy usage makes your space cool between the temperature range of 24 C 30 C Turbo runs Operate in auto fan speed to cool quickly Quiet AE 020 o e 066 Air swing S N Activate Deactivate air flow blade movement automatically up and down Fanav Adjust how much air flows through the air conditioner with the 4 different fan speeds such as Auto Low Medium High Temp Increase Decrease the temperature by 1 C Auto Clean Auto c
3. d light Cool function is only available in Cool mode When d light Cool function is activated temperature sets automatically and Fy _ will appear on the remote controller display If you press the Mode button while the d light Cool function is on it will cancel the function If using a multi system this function will work only when the d light Cool function is set on all operated indoor units 17 Panama AQVO9Y _IB amp IM_32445A_E indd 17 2011 1 19 16 22 58 Using the Quiet function You can reduce the noise generated from an indoor unit Press the Quiet button on the remote controller while the air conditioner is operating in Cool Heat mode gt Quiet indicator appears on the remote controller display gt The indoor unit will operate more quietly Cancel Press the Quiet button once again Cool gt SET C ju CC B If using a multi system this function will work only when the Quiet function is AM NOTE seton all operated indoor units 18 Panama_AQVO9Y _IB amp IM 32445A E indd 18 2011 1 19 16 22 54 MEME 6 Cleaning the air conditioner CAUTION Make sure the power is turned off and unplugged from the wall socket when cleaning the air conditioner Cleaning the indoor unit gt Wipe the surface of the unit with a slightly damp micro fiber cloth when needed Contact the service center when you clean the indoor unit heat exchan
4. e Screw Driver Spanner Drill e LWrench e Measuring Tape Tools for test operations e Thermometer e Resistance Meter Electroscope Fixing the installation plate You can select the direction of the drain hose depending on where you want to install the indoor unit Therefore before fixing the installation plate to a wall or a window frame you must determine the position of the 65mm hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the Right A Direction of pipe Left B E RS Underside right C Na AT B e Rear right or left D NG D D C 1 Push the V mark up at the bottom of the indoor unit to detach the plate 29 Panama AQV0O9Y _IB amp IM 32445A E indd 29 2011 1 19 16 23 14 Panama_AQVO9Y _IB amp IM 32445A E indd 30 2011 3 28 15 05 14 Fixing the installation plate 2 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards Unit mm Model A B C D Make sure to drill only one hole AQVXXK YX 20 120 95 20 Somon after choosing the direction of the pipe Pipe hole 065mm 1 J 3 Fix the indoor unit If you fix the indoor unit
5. Panama AQVO9Y IB amp IM 32445A E indd 1 2011 1 19 16 22 21 e On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest Beat the heat with your own air conditioner this summer Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but also can be an efficient heating method in the winter with the advanced Heat pump system Heat pump system is 3 times more efficient compare to the other electrical heating appliance so you can further reduce its running cost Now meet year round needs with one air conditioner i Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically good sleep function good sleep function allows you to set a comfortable sleep temperature while saving energy and having sound sleep d light Cool function d light Cool function allows you to keep the temperature and humidity at the most comfort level SPi Super plasma ion function SPi function generates hydrogen H and oxygen O to
6. Power supply line fuse or circuit breaker gt Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Always verify that a suitable grounding connection is available Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Always verify that the cut off and protection switches are suitably dimensioned Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners Choosing the installation location Indoor unit gt gt gt vv vV VvV V Panama AQV09Y _IB amp IM 32445A E indd 25 2011 1 19 16 23 02 Where airflow is not blocked Where cool air can be distributed throughout the room Install the refrigerant piping length and the height difference of both indoor and outdoor units as indicated in the installation diagram Wall that prevents v
7. fall In addition install a snow proof hood to avoid snow from piling on the Estimated outdoor unit ney fall Ground Purging the connected pipes The outdoor unit is loaded with sufficient R410A refrigerant Do not vent R410A into atmosphere it is a fluorinated greenhouse gas covered by Kyoto Protocol with a Global Warming Potential GWP 1975 You should purge the air in the indoor unit and in the pipe If air remains in the refrigerant pipes it affects the compressor It may cause reduction of cooling capacity and malfunction Refrigerant for air purging is not charged in the outdoor unit Use Vacuum Pump as seen in the picture e When installing make sure there is no leakage When recovering the refrigerant ground the compressor first before removing the connection pipe If the refrigerant pipe is not properly connected and the compressor works with the service valve open the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high It may cause explosion and injury 1 Connect each assembly pipe to the appropriate valve on the outdoor unitand Outdoorunit 4 Indoor unit tighten the flare nut Gas pipe See 2 Tighten the flare nut first with your hands and then with a torque wrench m m a applying the following torque Excessive torque can be cause of gas leakage Outer Diameter Torque kgf cm 66 35 mm 140 170 lt Make the electrical connection and
8. 3G 2 5mm HO7RN F amu mya be incorporated in a wire with a contact opening of 33mm Connecting the cable When you install the unit make first refrigerant connections and then electrical connections Connect the air conditioner to grounding system before performing the electrical connection If unit is uninstalled first disconnect electrical cables then refrigerant connections A 4 or 5 meter pipe is supplied with the air conditioner If the outdoor unit is more than 4 or 5 meters away from the indoor unit you must extend the cable The maximum length of the cable is 15 09 12 20 1893k meters 30 1 Extend the assembly cable if necessary Do not connect two or more different cables to extend the length caution lt may cause fire Open the front grille Remove the screw securing the connector cover Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals Refer to the picture below B Each wire is labeled with the corresponding terminal number NOTE 5 6 7 8 9 Pass the other end of the cable through the 65mm hole in the wall Close the connector cover by tightening the screw carefully Close the front grille Remove the terminal board cover on the side of the outdoor unit Connect the cables to the terminals as seen in the picture Each wire is labeled with the corresponding terminal number X 09 12 18X
9. The airflow blades work properly 4 Press the Power button to stop the operation When you complete the installation successfully hand over this manual to the user for storage in a handy and safe NOTE Place Pump down procedure when removing the product 1 Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes 2 Release the valve caps on High and Low pressure side 3 Use L wrench to close the valve on the high pressure side 4 Approximately 2 minutes after close the valve on the low pressure side 5 Stop operation of the air conditioner 6 Disconnect the pipes 41 Panama AQVO9Y IB amp IM 32445A E indd 41 2011 1 19 16 23 31 ae Y How to connect your extended power cables Items to prepare compressor and insulation tape should be prepared by an installation technician Crimping plier Connection sleeve mm Insulation tape Contraction tube mm MH 14 20x 7 0 HxOD Width 18mm 50x 8 0 LxOD HS 1 As shown in the figure peel off the shields from the rubber wire Unit mm of the power cable Power cable provided by us Peel off 20 mm of the wire shields of the tube installed already A After peeling off the tube wire you must insert a contraction tube CAUTION 2 Insert both sides of core wire of the power cable into the connection sleeve 3 Using acompressor compress the two points and flip it over and compress another two
10. 37 CU Basic function Basic operation is an operation mode that can be selected by pressing the Mode button Auto In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season e If current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness lt Quiet modelsk A makes the noise quieter during the operation of the indoor unit in the Cool mode Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room Heat The air conditioner heats as well as cools Warm your room with this versatile appliance in the cold of winter Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up lt Quiet modelsk P makes the noise quieter during the operation of the indoor unit in the Heat mode Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrea
11. 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipes of different diameters e The smaller one is for the liquid refrigerant The larger one is for the gas refrigerant A short pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional non The connection procedure for the refrigerant pipe varies Re aa eee according to the exit position of the pipe when facing the wall lt Right A AH x Pe Left B be 7 Underside C Rear 1 Cut out the appropriate knock out piece A B C on the rear of the indoor Outer planets Torque kgf cm unit unless you connect the pipe directly from the rear 66 35 mm 140 170 2 Smooth the cut edges 99 52 mm 250 280 612 70 mm 380 420 3 Remove the protection caps of the pipes and connect the assembly pipe 615 88 mm 440 480 to each pipe Tighten the nuts first with your hands and then with a 619 05 mm 990 1210 torque wrench applying the following torque 022 23 mm 990 1210 If you want to shorten or extend the pipes refer to page 33 34 NOTE 4 Cut off the remaining foam insulation 5 If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole gt The pipe should not project from the rear of the indoor un
12. If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer HSITON3 After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries To prevent injury when accidentally touching the indoor unit fan install the indoor unit at least 2 5m above the floor The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs The units components must be accessible and that can be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the Installation Manual the cost necessary to reach and repair the unit in safety as required by current regulations in force with slings trucks scaffolding or any other means of elevation won t be considered in warranty and charged to end user
13. SOCK KKK 0000 00504 BOSSI KKK KK KOSS ROKK KG KIN WR ROSS DS NS XO HK NG KS Le te Nasa SS Kg ROK 2 09 2 KN RR Heat exchanger Illustration may differ slightly depending on the models 2011 1 19 16 22 56 19 HSITON3 TH Can Cleaning the air conditioner Removing the Full HD filter Grab the handle and lift it up Then pull the Full HD filter towards you and slide it down JI 7 aa aaa Mi y Cleaning the Full HD filter Washable foam based Full HD filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing Open the panel and put the Full HD filter out Clean the Full HD filter with a vacuum cleaner or soft brush If dust is too heavy rinse it with running water Insert the Full HD filter back in its original Dry the Full HD filter in a ventilated area position and close the front panel Clean the Full HD filter every 2 weeks Cleaning term may differ depending on the usage and environmental NOTE Conditions In dusty area clean it once a week If the Full HD filter dries in a confined or humid area odors may generate If it occurs re clean and d
14. attack undesirable air contaminants such as bacteria pollen and odor It makes you breathe better as if you are staying around waterfalls ocean surf rivers and mountains Panama_AQVO9Y _IB amp IM_32445A_E indd 2 Features of your new air conditioner Contents Cool Summer Offer USING PARTS Safety precautions ones 3 Checking before use insister 6 Checking the name of the parts ssesessssssssesseesssssssessee 7 Checking the remote controller nn 8 Basic Ue en AA AAAH HABA ee 10 Adjusting the air flow direction wessssssessssssesssssssssssseseen 12 Using the Turbo function ns 12 good sleep mode mamasa 13 Setting the Current time 0 00e0esesese aee aane anaa aaaa nean een 14 Setting the On Off timer 2e 14 Using the Smart Saver function 16 Using the SPi function rs 16 Using the Auto Clean function ns 17 Using the a light Cool function rs 17 Using the Quiet function sms 18 Cleaning the air conditioner ns 19 Maintaining the air conditioner ssssssseesessessssesseesesseeen 21 Troubleshooting mamamana mamana 22 INSTALLATION PARTS Safety PRECAUONS sssini 24 Choosing the installation location sssssssesssssesssssseeseses 25 ACCES OS datent 28 Fixing the installation plate 29 Connecting the assembly cable nn 30 Installing and connecting the assembly pipe of the indoor WINE sssssssisassesisrssssesistarsssibssesisinssssss 32 Purging the indoor UNI ssiccutserssseitasistidennincatianetn
15. desired position Vertical air flow Air flow blades move up and down Press the Air swing button on the remote controller gt Air swing indicator will be on the remote controller display and air flow blades move up and down continuously to circulate the air gt Press the Air swing button on the remote controller again to keep the air flow direction in a constant position SET C ja Horizontal air flow Air flow blades move left and right Press the Air swing I button on the remote controller gt Air swing indicator will be on the remote controller display and air flow blades move left and right continuously to circulate the air gt Press the Air swing JIN button on the remote controller again to keep the air flow direction in a constant position Adjusting the air flow direction is not available in good sleep mode while it is in NOTE Cool mode However you can adjust the air flow direction in good sleep mode LES while it is in heat mode Using the Turbo function Turbo function will be helpful to cool your room quickly and effectively Press the Turbo rune button on the remote controller during Cool mode gt Turbo indicator appears on the remote controller display and the air conditioner operates in Turbo function for 30 minutes Cancel Press the Turbo runs button once again Turbo function is only available in Cool mode NOTE lt If you press the Mode button while the
16. gas may leak gt This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall gt Ifthe outdoor unit falls it may result in injury death or property damage This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line gt Failure to do so may result in electric shock fire an explosion or other problems with the product gt Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes FOR INSTALLATION CAUTION O This appliance should be positioned in such a way that it is accessible to the power plug gt Failing to do so may result in electric shock or fire due to electric leakage Install your appliance on a level and hard floor that can support its weight gt Failing to do so may result in abnormal vibrations noise or problems with the product Install the draining hose properly so that water is drained correctly gt Failing to do so may result in water overflowing and property damage When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly gt The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property da
17. gt This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance unplug the air conditioner from the wall socket and wait until the fan stops gt Failing to do so may result in electric shock or fire FOR CLEANING CAUTION Q O Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges gt To avoid cutting your fingers wear thick cotton gloves when cleaning it Do not clean the inside of the air conditioner by yourself gt For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning the air conditioner section gt Failure to do may result in damage electric shock or fire Panama_AQVO9Y _IB amp IM_32445A E indd 5 2011 1 19 16 22 28 Checking before use Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use Mode Indoor temperature Outdoor temperature Indoor humidity Cooling 16 C 32 C 10 C 46 C Relative humidity 80 or less Heating 27 C or less 15 C 24 C Dry 18 C 32 C 10 C 46 C gt If the air conditioner operates in cooling mode for long period of time in high humidity area dew may be formed gt If the outdoor temperature goes down to 5 C heating capaci
18. injury Do not operate the appliance with wet hands gt This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance gt As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the water from the air conditioner gt The water may be harmful to humans Do not apply a strong impact to the remote controller and do not disassemble the remote controller Do not touch the pipes connected with the product gt This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes gt This may result in property damage Avoid directly exposing humans animals or plants from the air flow from the air conditioner for long periods of time gt This may result in harm to humans animals or plants This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance FOR CLEANING WARNING O Do not clean the appliance by spraying water directly onto it Do not use benzene thinner or alcohol to clean the appliance
19. leave the system into stand by 99 52 mm 250280 mode Do not turn on the system 612 70 mm 380 420 This is necessary for better vacuum operation full OPEN position of 015 88 mm 440 480 Electronic Expansion Valve EEV 619 05 mm 990 1210 022 23 mm 990 1210 36 Panama_AQVO9Y _IB amp IM 32445A E indd 36 2011 1 19 16 23 26 3 Connect the charging hose of the low pressure side of manifold gauge to a Manifold gauge gas service port as seen in the picture 4 Open the valve of the low pressure side of manifold gauge counterclockwise Valve gt 5 Purge the air in the connected pipes using the vacuum pump for about Gas service port 15 minutes j lt Low pressure gt gt Make sure that pressure gauge shows 0 1MPa 76cmHg after about 10 minutes This procedure is very important to avoid a gas leak gt Close the valve of the low pressure side of manifold gauge clockwise gt Turn off the vacuum pump Vacuum gt Check for 2 minutes if there is any pressure change Liquid service port amp lt High pressure gt Backward flowing gt Remove the hose of the low pressure side of manifold gauge prevention 6 Set a valve cork of liquid and gas service port to the open position 7 Mount the valve stem nuts and the service port cap to the valve and tighten Vane siem them at the torque of 183kgf cm with a torque wrench Stem nut SAN 8 Check for a gas l
20. on a wall 1 Fix the installation plate to the wall giving attention to the weight of the indoor unit Plastic lt Ifyou mount the plate to a concrete wall using plastic anchors make sure that Anchor Pa NOTE gaps between the wall and the plate created by projected anchor is less than On f IS 20mm VA If you fix the indoor unit on a window frame If you fix the indoor unit on a gypsum board 1 Determine the positions of the wooden uprights to be 1 Use stud finder to find out locations of the studs attached to the window frame 2 Fix the plate hanger on two studs 2 Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit 3 Attach the installation plate to the wooden upright using tapping screws Search for other spots if there are less than two studs or the distance between the studs are different from the caution Plate hanger Fix the installation plate without inclining to one side Make sure that a wall can withstand the weight of the product If you install the product in a place where it is not WARNING Strong enough to withstand the product weight the unit could fall and cause injury Connecting the assembly cable Cable specification Model Powercable Interconnection cable E e Connect the power cable to the auxiliary Lee circuit breaker If every pole fails to 09 122 3G 1 5mm HO7RN F 20A pedo pose ny i X 18 24X
21. points in the same location The compression dimension should be 8 0 After compressing it pull both sides of the wire to make sure it is firmly pressed TE it 4 times 5mm 4 Wrap it with the insulation tape twice and position your Insulation tape contraction tube in the middle of the insulation tape p 5 Apply heat to the contraction tube to contract it 40mm paahon tube ag tape In case of extending the electric wire please DO NOT use a round shaped pressing socket 6 After tube contraction work is completed wrap it with the insulation tape to finish A Incomplete wire connections can cause electric shock or a fire po T 42 Panama AQVO9Y IB amp IM 32445A E indd 42 2011 1 19 16 23 92 HSITON3 43 Panama_AQVO9Y _IB amp IM 32445A E indd 43 2011 1 19 16 23 33 Psa SUN QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT ARGENTINE 0800 333 3733 www samsung com 0800 124 421 BRAZIL 4004 0000 www samsung com CHILE 800 SAMSUNG 7 26 7864 www samsung com COLOMBIA 01 8000112112 www samsung com COSTA RICA 0 800 507 7267 www samsung com DOMINICA 1 800 751 2676 www samsung com ECUADOR 1 800 10 7267 www samsung com EL SALVADOR 800 6225 www samsung com GUATEMALA 1 800 299 0013 www samsung com HONDURAS www samsung com JAMAICA 1 800 234 7267 www samsung com NICARAGUA 00 1800 507 7267 www samsung com
22. result in children seriously injuring themselves Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people gt Since this may be dangerous due to a lack of oxygen Open a window at least once an hour If any foreign substance such as water has entered the appliance cut the power by unplugging the power plug and turning the circuit breaker off and then contact your nearest service center gt Failing to do so may result in electric shock or fire HSITON3 Do not attempt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse gt Failing to do so may result in electric shock fire problems with the product or injury FOR USING NCAUTION Do not place objects or devices under the indoor unit gt Water dripping from the indoor unit may result in fire or property damage Check that the installation frame of the outdoor unit is not broken at least once a year gt Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance gt This may result in electric shock fire problems with the product or
23. AUTION When not using the air conditioner for a long period of time or during a thunder lightning storm cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING WARNING WD 4 If the appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning smell or smoke unplug the power plug immediately and contact your nearest service center gt Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power plug Do not touch the appliance or power cord gt Do not use a ventilating fan gt A spark may result in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center Do not touch the power plug or the circuit breaker with w
24. Formaximum safety installers should always carefully read the following warnings Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred b This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non compliant units gt The air conditioner is compliant with the requirements of the Low Voltage Directive 72 23 EEC the EMC Directive 89 336 EEC and the Directive on pressurized equipment 97 23 EEC gt The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty gt The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry gt Donotuse the units if damaged If problems occur switch the unit off and disconnect it from the power supply In order to prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNG technical support if the unit produces smoke
25. If you install the outdoor unit in a place exposed to strong winds or at a height fix it to an appropriate support wall or ground 1 Place the outdoor unit as indicated on the top of the unit to let the discharged air out properly 2 Fix the outdoor unit in level to an appropriate support using anchor bolts 3 Ifthe outdoor unit is exposed to strong winds install shield plates around the outdoor unit so that the fan can operate correctly e Secure the rubber leg to prevent the generation of noise and vibration NOTE Outdoor unit installed on the wall by rack Ensure the wall will be able to suspend the weight of rack and outdoor unit p Install the rack close to the column as much as possible Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall Connecting wires Drain hose Insulation s Rubber leg Model X Y AQVXXK YX 612 317 Designed to cut off residual vibration from outdoor unit to rack not supplied with product Soft rubber designed to cut off vibration from rack to wall not supplied with product 40 Panama AQVO9Y _IB amp IM_32445A_E indd 40 2011 1 19 16 23 29 SCL j i E Final Check and Trial Operation To co
26. L j i Cutting or extending the pipe 5 Check if you flared the pipe correctly see examples of incorrectly flared pipes below Correct Inclined Damaged Cracked Uneven Surface Thickness 6 Align the pipes to connect them easily Tighten the flare nuts first with your hands and then with a torque wrench applying the following torque Flare nut Outer Diameter Torque kgfecm 06 35 mm 140 170 99 52 mm 250 280 see g12 0 mm 380 420 015 88 mm 440 480 019 05 mm 990 1210 Indoor outlet pipe Connecting pipe 622 23 mm 990 1210 Excessive torque can be cause of gas leakage In case brazing the pipe the nitrogen gas must be blown into the NOTE pipe 50 Pa The joint must be accessible and serviceable 7 For further details on how to connect to the outdoor unit and purge the air refer to page 36 38 Tighten the flare nut with torque wrench according to specified method caution __ the flare nut is over tightened the flare may break and cause refrigerant gas leakage Installing and connecting the drain hose of the indoor unit When installing the drain hose for the indoor unit check if condensation draining is adequate When passing the drain hose through the 65 mm hole drilled in the wall check the followings Wall Indoor unit Drain hose The drain hose must NOT The end of the drain hose must NOT slant upwards be placed under water 0 0 0 5cm less adl amp Ditch The drain ho
27. PANAMA 800 7267 www samsung com PERU 0 800 7 77 08 www samsung com PUERTO RICO 1 800 682 3180 www samsung com TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 www samsung com VENEZUELA 0 800 100 5303 www samsung com Panama AQVO9Y IB amp IM 32445A E indd 44 2011 3 28 15 23 20 AQVO9K Series AQV12KX Series AQV18K Series AQVO9Y Series AQV12Y Series AQV18Y Series imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com register BOP DB98 32445A 2 en Panama_AQVO9Y IB8IM 32445A E indd 45 2011 3 28 15 33 21
28. Turbo function is on it will cancel the function e Temperature Fan speed cannot be adjusted while using this function 12 Panama AQVO9Y _IB amp IM_32445A_E indd 12 2011 1 19 16 22 43 Panama AQV0O9Y _IB amp IM 32445A E indd 13 2011 2 10 11 42 16 good sleepmode Before using good sleep mode set the current time For setting current time refer to the page 14 For a comfortable sleep the air conditioner will operate it Fall asleep gt Sound sleep gt Wake up from good sleep mode When the air conditioner is on and in cool heat mode 1 Press the good sleep button on the remote controller gt good sleep indicator appears and Off timer indicator starts blinking on the remote controller display HSITON3 2 Press the good sleep button to set the time gt You can set the time in half hourly unit from 30 minutes 3 hours and hour unit from 3 hours 12 hours gt Operating hour can be set from minimum 30 minutes to maximum 12 hours gt Default operation hour is set to 8 hours 3 Press the Set Cancel button to active it gt Off timer indicator stops blinking and reserved time will be displayed for 3 seconds Then the air conditioner operates in good sleep Cool mode gt If you don t press Set Cancel button within 10 seconds after pressing the good sleep button the air conditioner will return to previous status Check Off timer indicator and ind
29. X 485 Communication type Indoor unit i aa Too T Ground wire Green Yellow Outdoor unit Ground wire QE Green Yellow LIN AE Outdoor ae 7 End of the wire must be circular caution After connecting the cables make sure terminal numbers on the indoor outdoor unit matches e Screws on terminal block must not be unscrewed with the torque less than 12kgf cm HSITON3 10 Connect the grounding conductor to the grounding terminals 11 Close the terminal board cover by tightening the screw carefully In Russia and Europe consult with the supply authority to determine the supply system impedance before installation Connect the wires firmly so that wires can not be pulled out easily If they are loose it could cause burn out of the wires Connect the wires according to color codes referring to the wiring diagram The power cable and the interconnection cable should be selected according to the specification in page 30 Panama AQVO9Y IB amp IM 32445A E indd 31 31 2011 2 12 1541 12 SCL j i a Installing and connecting the assembly pipe of the indoor unit Connect indoor and outdoor units with field supplied copper pipes by means of flare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to ISO1337 degreased and deoxidized suitable for operating pressures of at least
30. accessible and serviceable Changing direction of the drain hose Change the direction only when it is necessary 1 Detach the rubber cap with the plier Screw hole Screw 2 Detach the drain hose by pulling it and turning to the left 3 Insert the drain hose by fixing it with the screw into the groove of the drain hose and the outlet of the drain pan 4 Attach the rubber cap with a screwdriver by turning it to the right until it fixes to the end of the groove 5 Check for leakage on both side of the drain outlet Pour the water in direction of arrow se Direction of the drained water 35 Panama AQV09Y _IB amp IM 32445A E indd 35 2011 1 19 16 23 25 Installing and connecting the drain hose of the outdoor unit While heating ice may accumulate During the process of defrosting check if condensation draining is adequate For adequate draining do the following 1 Insert the drain plug into the drain hole on the underside of the outdoor unit To avoid drain plug from contacting the ground secure gap between the caution ground and the bottom surface of the outdoor unit 2 Connect a drain hose to the drain plug 3 Ensure that condensation draining is adequate lt In areas with heavy snow fall piled snow could block the air intake caution TO avoid this incident install a frame that is higher than estimated snow
31. aes 33 Cutting or extending the pipe mm 33 Installing and connecting the drain hose of the indoor unit nr 34 Changing direction of the drain hose Uu aswa 35 Installing and connecting the drain hose of the outdoor unit nr 36 Purging the connected pipes ns 36 Performing the gas leak tests sessssssssseseesssssssessesessses 39 Fixing the indoor unit in place ssssssssssssssssssesssessosessssssesessess 40 Fixing the outdoor unit in place s s ssssssssssssssssssssesessssssesessess 40 Final check and trial operation sssssssseessesssssseeseessessssen 41 Pump down procedure when removing the product mms 41 How to connect your extended power cables 42 2011 1 19 16 22 22 SCL j i Safety precautions Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions HSITON3 A WARNING Hazards or unsafe practices that may result in severe personal injury or death A CAUTION Hazards or unsafe practices that may result in minor personal injur
32. air conditioner 300mm or more 125mmp fin Fee eel 125mm o or more E le Ure or more A A Wrap the refrigerant pipes and the drain hose dede of with the absorbent pad and vinyl tape Refer to draining page 40 for further details left or right L m as maximum pipe length and 3 mas minimum pipe length CAUTION It will reduce noise and vibration H meters maximum total pipe length L meters maximum 600mm total pipe length minimum 300mm minimum Ss 600mm minimum Model L H 09 12K 15 8 KHI BKK 30 15 Make at least one round It will reduce noise and vibration NG 34 The appearance of the unit may be different from the diagram depending on the model 26 Panama_AQVO9Y _IB amp IM 32445A E indd 26 2011 2 10 14 05 55 SCL j i E Space Requirements for Outdoor Unit When installing 1 outdoor unit Figure Description Z Top view Side view Air intake T Air outlet 4 Air intake Air outlet gt d 4 Air flow direction Unit mm When the air outlet is opposite the When the air outlet is towards the When 3 sides of the outdoor unit are wall wall blocked by the wall U PA AMONDO LA R ER D 5 7 Ll A O TJ Gis 8 ro o y a LR A kii 150 or more 600 or more The upper part of the outdoor unit The upper part of the outdoor unit Wh
33. cked by dirt If there is a lot of dust on the Full HD filter cooling heating performance may decrease Clean them frequently e Check if the outdoor unit is covered or installed near the obstacle Take the cover off and take the obstacle away Ifyou want to operate the air conditioner in the sunlight cover the outdoor unit using curtains or etc e Check if the air conditioner is operating in De ice mode When the ice formed in winter or the outdoor temperature is too low the air conditioner operates in De ice mode automatically In De ice mode indoor fan stops and cool air does not come out cy Ifthe doors or windows are open it may cause bad cooling heating performance Close the doors and windows e Check if the air conditioner has just been turned on after stopping cooling or heating operation In this case just a fan will run to protect the outdoor unit compressor e Check if the pipe length is too long When the pipe length exceeds maximum allowable pipe length cooling heating performance may decrease Air flow adjustmentisnot lt Checkifyou have selected good sleep mode In these modes and you cannot adjust the working air flow direction If the good sleep mode is operating in Heat mode you can adjust the air flow direction Fan speed adjustment is Check if you have selected Auto Dry Turbo good sleep d light Cool mode In these not working mode fan speed is set to Auto and you cannot adju
34. e Batteries for Installation Plate 1 Remote controller User s amp Installation Manual 1 Remote controller 2 The number of each accessory is indicated in parentheses Accessories in the outdoor unit case 4 wire Assembly Cable 1 Drain Plug 1 Rubber Leg 4 CS The flare nuts are attached to the end of each pipe of an evaporator or a service port Note Use the nuts when connecting the pipes The 4 wire assembly cable is optional If it is not supplied use the standard cable The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly pipe as seen in the picture 28 Panama_AQVO9Y _IB amp IM 32445A E indd 28 2011 1 19 16 23 10 CU a E Optional accessories The following connection accessories are optional If they are not supplied you should obtain them before installing the air conditioner Insulated Insulated Assembly Insulated Assembly Pipe PET3 Foam Tube Vinyl Tapes 2 Drain Plug 1 Rubber Legs 4 Assembly Pipe Pipe 09 52mm 1 012 70mm 1 Insulation 1 0635mm 1 XK09 12XX XK18XX 2 Ss M4 x 25 Tapped Drain Hose Screws 6 length 2m 1 B If these accessories are supplied they will be in the accessory box NOTE Tools required for installation General Tools Vacuum Pump Backward flowing prevention e Manifold Gauge e Stud Finder e Torque Wrench e Pipe Cutter e Reamer e Pipe Bender e Spirit Level
35. eak paying particular attention to the 3 way valve s stem nuts and to the service port cap Refer to page 39 ko g fau Adding Refrigerant Add refrigerant charge according to table below A 4 or 5 meter pipe is supplied with the air conditioner Model A i than 4 or 5m you use a pipe longer than 4 or 5m EE ie Ag of refrigerant R410A must be added for each extra meter 18 20 If you use a pipe shorter than 4 or 5 m The purge time is normal Refer to the Service Manual for further details The remaining air in the Refrigeration cycle which contains moisture may cause malfunction on the compressor caution Always contact the service center or a professional installation agency for product installation 37 HSITON3 Panama_AQVO9Y _IB amp IM 32445A E indd 37 2011 1 19 16 23 27 SCL j i a E Purging the connected pipes Important information regulation regarding the refrigerant used This product contains fluorinated greenhouse gases covered by the Kyoto Refrigerant type GWP value Protocol Do not vent gases into the atmosphere R410A 1975 GWP Global Warming Potential 1 Please fill in with indelible ink gt the factory refrigerant charge of the product Contains fluorinated greenhouse gases gt Q the additional refrigerant amount charged in the field and akak LL a gt the total refrigerant charge on the refrigerant charge label supplied with
36. ears on the remote controller display 2 Press Time Set button to set the current time gt AMor PM indicator will blink and you can set the time by pressing Temp hr or button for hour and Fan min Aw button for minute 3 Press Time Set button again to active it EY Setting the On Off timer e Check the current time on the remote controller before using this function caution The default time is 12 AM on the remote controller The current time is reset to default time after changing the batteries You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is on Setting On timer 1 Press the On Timer Off Timer button gt On Off timer indicator will blink on the remote controller display 2 Press the Temp hr or button and Fan min Aw button to set the time gt You can set the time in hourly units from 1 hour 12hours according to AM PM and in minute units from 1minute 59minutes Panama_AQVO9Y _IB amp IM_32445A E indd 14 2011 1 19 162247 Setting Off timer 3 Press the Set Cancel button to active it gt On timer indicator stops blinking and reserved time will be displayed for 3 seconds gt If you don t press Set Cancel button within 10 seconds after selecting the time the air conditioner will return to previous status Check On time
37. en the walls are blocking front and the air outlet is towards the wall and the air outlet is opposite the and the rear side of the outdoor unit wall o o ADASA MA E 2 oS 2000 or more 6 5 kme A U P O O E When installing more than 1 outdoor unit Unit mm When the air outlet is towards the wall When 3 sides of the outdoor unit are blocked by the wall U U U v gt L L g g g g 5 o 7 8 O li LIL Ty ts O lt t D lt lt m lt m ag 300 or more 600 or more 6000rmore 600 or more 27 Panama AQVO9Y _IB amp IM_32445A_E indd 27 2011 1 19 16 23 07 SCL j i BNN Choosing the installation location Unit mm When the walls are blocking front and the rear side of the outdoor units When the upper part of the outdoor unit LILI LIL LL LL i and the air outlet is opposite the wall Bio i QE go LI sawan ome dts V 55 S 18 g 600 or be oe 600ormorey 2 E D When front and rear side of the outdoor unit is towards the wall Url ol 1500 or 600 or pA Or a Or bg Or more more more more more 500 or more e Ifinstallation is done in inappropriate space unit may generate sound and cause bad effect on the product caution Installation must be done in level and in a place where vibration will not cause any effect Accessories The following accessories are supplied with the air conditioner NOTE l Accessories in the indoor unit cas
38. et hands gt This may result in electric shock Do not unplug the power plug or turn the air conditioner off with the circuit breaker while it is operating gt Plugging the power plug into the wall outlet or turning the air conditioner on from the circuit breaker may cause a spark and result in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children gt Ifa child places a bag over its head it may result in suffocation Do not insert your fingers or foreign substances into the outlet when the air conditioner is operating gt Take special care that children do not injure themselves by inserting their fingers into the product Do not touch the air flow blade with your hands or fingers during the heating operation gt This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air conditioner gt Take special care that children do not injure themselves by inserting their fingers into the product Do not strike or pull the air conditioner with excessive force gt This may result in fire injury or problems with the product Panama AQVO9Y IB amp IM 32445A E indd 4 2011 1 19 16 22 28 SCL j i FOR USING WARNING Do not place an object near the outdoor unit that allows children to climb onto the machine gt This may
39. ger because it needs to be disassembled Since the panel of the indoor unit is easily scratched you should use a micro fiber cloth to clean the panel When you use the micro fiber cloth slightly dampen the cloth and remove any debris on the cloth to avoid scratches Do not clean the display using alkaline detergent Do not use sulfuric acid hydrochloric acid organic solvents such as thinner kerosene and acetone etc to clean the surface of the product or put any stickers on it They may damage the surface of the air conditioner Cleaning the outdoor unit heat exchanger gt When dust accumulates on the heat exchanger it may decrease cooling performance Therefore clean it regularly gt Spray water to clean the dust NOTE CAUTION If itis difficult to clean the outdoor unit heat exchanger on your own contact service center Be careful with the sharp edges on the outdoor unit heat exchanger j Opening the panel Tightly grip each side of the front panel and lift the panel up to open Then release the panel which should be automatically positioned to hold the panel open gt To close the panel slightly lift up the front panel while pushing gently and lower the panel Panama AQVO9Y _IB amp IM_32445A_E indd 19 LISE KISS 8 lt gt 2X RK SRK KKK PSK KEL KOS 0000059 0 0 AK KO PR KIKO KIKI RK KOOKS SOS KOC SRK KKK SSK KSC SRR KL KS KR CSE KROL
40. ibration and is strong enough to hold the product weight Out of the direct sunlight 1m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated As far away as possible from the fluorescent and incandescent lights so that the remote controller can be operated well A place where the air filter can be replaced easily 25 SCL j i E Choosing the installation location Outdoor Unit Where it is not exposed to strong wind Well ventilated and dustless places Out of the direct sunlight and rain Where neighbors are not annoyed by operation sound or hot air Solid wall or support that prevents vibration and is strong enough to hold the product weight Where there is no risk of flammable gas leakage When installing the unit at a high place be sure to fix the unit legs 3m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated Install the unit horizontally Place where drained water does not become any problem Place with no plants especially climbing plants and where small animal can not access vY V YV vV V V V vv V AN Avoid the following places to prevent malfunction of the unit caution Where there is machine oil Salty environment such as seaside areas Where sulfide gas exists Other special atmosphere areas Observe the clearances and maximum lengths as seen in the picture below when installing the
41. icator on the indoor unit Cancel Press the Set Cancel button once again i You can set the desired temperature by 1 C in the range of 16 C 30 C Fan speed will be adjusted automatically according to the good sleep 4 mode J However f you select good sleep mode while heating operation is on you can adjust fan speed When the good sleep mode is on In Cool mode Air flow direction will be adjusted automatically In Heat mode Adjusting air flow direction is available Temperature and fan speed changes in good sleep mode Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up from good sleep mode Allows you to wake up from comfortable intermittent air and it makes you feel refreshed lt Set Off timer in good sleep mode over 5 hours You fell disturbed sleep if the good sleep is set too short or long NoTE because the default is set to 8 hour operation Ifthe good sleep mode is set less than 4 hours the operation will stop at the same time If the good sleep mode is set over 5 hours it will run as Wake up stage from the last one hour before it stops Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating 13 Setting the Current time Before using the functions of the air conditioner set the current time 1 Press 2 F button gt 2 4F indicator app
42. if the power cable is hot or damaged or if the unit is very noisy gt Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only The unit contains moving parts which should always be kept out of the reach of children gt Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires Do not place containers with liquids or other objects on the unit All the materials used for the manufacture and packaging of the air conditioner are recyclable gt The packing material and exhaust batteries of the remote controller optional must be disposed of in accordance with current laws gt The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely 24 Panama AQVO9Y IB amp IM 32445A E indd 24 2011 1 19 16 23 02 SCL j l Installing the unit IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines gt Always disassemble the electric lines before the refrigerant tubes Upon receipt inspect the product to verify that it has not been damaged during transport
43. it gt The bending radius should be 100 mm or more 6 Pass the pipe through the hole in the wall 7 For further details on how to connect to the outdoor unit and purge the air refer to page 36 38 The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test NOTE referto page 39 40 for further details Tighten the flare nut with torque wrench according to specified method caution __ the flare nut is over tightened the flare may break and cause refrigerant gas leakage DO NOT WALL UP THE PIPE CONNECTION All refrigerant pipe connection must be easy accessible and serviceable 32 Panama_AQVO9Y _IB amp IM 32445A E indd 32 2011 1 19 16 23 20 Purging the indoor unit The indoor unit is supplied with inert gas nitrogen Before installing the unit check if nitrogen gas flow out of indoor unit If this one isn t true DO NOT INSTALL THE UNIT since leakage could be inside the indoor unit 1 Unscrew the caps at the end of each pipe gt All inert gas exhausts from the indoor unit oe HSITON3 e To prevent dirt or foreign substances from getting into the pipes during NOTE installation do NOT remove the caps completely until you are readyto _ connect the pipes e The remaining air in the Refrigeration cycle which contains moisture Pipes Unscrew the caps cauti
44. lean function Dry inside of the indoor unit to get rid of odor JE aE dlight Cool Ca Gs good sleep Set the d light Cool function on off isplay Off Set the good sleep mode on On Timer Set Set Cancel Set the On Timer on oe Wi Gee Cancel the timer good sleep mode Off Timer Set the Off Timer on 2 F Switch the function of the button on the remote controller Temp Humi Beep off Display the room humidity level and temperature value for 5 To silence the beep sound when pressing the button seconds on the indoor unit display Display off Hi High If the relative humidity is 70 or higher To turn off the display light Sd Standard If the relative humidity is lower than 70 Time set For room temperature will be displayed the value Set the current time When you press 2 F button the indicator will be displayed on the remote controller and you can change the functions on the remote controller as listed below d light Cool gt Temp Humi Auto Clean b Beep Off good sleep Display Off On Timer b Time Set function If you select the function under the button while the function of the button is switched by 2 F button the 2 F function is canceled 8 Panama_AQVO9Y _IB amp IM_32445A E indd 8 2011 1 19 16 22 33 AN Make sure that the water does not get to the remote controller CAUTION Battery changing time Quiet indicator Turbo indicator SPi indicator Smart Save
45. mage Panama_AQVO9Y _IB amp IM_32445A E indd 3 2011 1 19 16 22 28 e Safety precautions FOR POWER SUPPLY WARNING a Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis gt Unplug the power plug and clean it with a dry cloth gt Failing to do so may result in electric shock or fire Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor gt Ifyou plug the power plug into the socket in the opposite direction the electric wires within the cable may be damaged and this may result in electric shock or fire When the appliance or power plug or power cord is damaged contact your nearest service center Plug the power plug into the wall socket firmly Do not use a damaged power plug damaged power cord or loose wall socket gt This may result in electric shock or fire Do not pull the power cord when unplugging the power plug gt Unplug the power plug by holding the plug gt Failing to do so may result in electric shock or fire Do not pull or excessively bend the power cord Do not twist or tie the power cord Do not hook the power cord over a metal object place a heavy object on the power cord insert the power cord between objects or push the power cord into the space behind the appliance gt This may result in electric shock or fire FOR POWER SUPPLY C
46. ment changes It is normal Smoke is generated from If may not be a fire but it can be a steam generated by the defrost operation from outdoor the outdoor unit heat exchanger during Heat mode in winter Water is dropping from Water may be generated because of the temperature difference It is normal the outdoor unit piping connection 23 Panama_AQVO9Y _IB amp IM 32445A E indd 23 2011 1 19 16 23 01 W HEI lt INSTALLATION PARTS X In this manual you may find model names written in simplified forms as indicated in following table Model Names Included Models AQV K AQVO9K AQV12K AQV18K PEE E EN AOVKKYX AQVO9Y AQV12Y AQV18Y ping ala XXXK09 X X AQVO9KK AQVO9Y XXX12XX AQV12KX AQV12Y Grouping was done by capacity XXXK18X X AQV18KX AQV18Y Safety precautions Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment e Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components e Verify that installation and testing operations are performed by qualified personnel e Verify that the air conditioner is not installed in an easily accessible area General information gt Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order to be able to use it as reference after installation gt
47. mplete the installation perform the following checks and tests to ensure that the air conditioner operates correctly Check the followings e Strength of the installation site e Tightness of pipe connection to detect gas leak e Electric wiring connection e Heat resistant insulation of the pipe Drainage Grounding conductor connection e Correct operation follow the steps below HSITON3 1 Press the Power button and check the following B 4 gt The indicator on the indoor unit lights up gt The airflow blade opens and the fan gears up for operation 2 Press the Mode button to select Cool or Heat mode E uto wet gt In Cool mode use Temp hr or button and set the temperature at 16 C gt In Heat mode use Temp hr or button and set the temperature at 30 C B Approximately 3 5 minutes later outdoor unit will start to operate and the O nee Note Cool or Warm air will blow out After 12 minutes of stationary condition check the indoor unit air treatment e Cooling mode indoor unit check gt Inlet air temp Outlet air temp From 10 K to 12 K indicative delta T Heating mode indoor unit check gt Outlet air temp Inlet air temp N From 11 K to 14 K indicative delta T In heating mode the indoor fan motor can remain off to avoid cold air blown into IN conditioned space 3 Press the Air swing 5 JIN button and check the following gt
48. on May cause malfunction on the compressor lt Always contact the service center or a professional installation agency for product installation Cutting or extending the pipe A 4 or 5 meter pipe is supplied with the air conditioner The length of the pipe can be Extended up to see table page 26 Shorten up to see page 26 If you need a pipe longer than 4 or 5 meters caution You must extend the assembly cable You must add refrigerant to the pipes otherwise the indoor unit may freeze 1 Make sure that you have all the required tools pipe cutter reamer flaring tool and pipe holder 2 Ifyou want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe see below examples of correct and incorrect cut edges Pipe 90 cutter Pipe 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer A Face the pipe down while removing the burrs to make sure that burrs do not get in to the pipe CAUTION 4 Puta flare nut slightly into the pipe and modify the flare D b Outer Diameter D Depth A Flaring Size B A 06 35 mm 1 3 mm 9 0 mm a 09 52 mm 1 8 mm 13 0mm a 612 70 mm 2 0 mm 16 2 mm a 615 88 mm 2 2 Mm 19 3 mm ba 619 05 mm 2 2 mm 22 5 mm Pipe Flare 022 23 mm 2 2 mm 25 7 mm 33 Panama_AQVO9Y _IB amp IM 32445A E indd 33 2011 1 19 16 23 21 SC
49. oor unit and outdoor unit insulating the cables hose and pipe and fixing the indoor unit to the installation plate HSITON3 To check for gas leaks on the outdoor unit Check the valve A and B using a leak detector To check for gas leaks on the indoor unit Check the flare nut C and D using a leak detector Leak test with nitrogen before opening valves In order to detect basic refrigerant leaks before recreating the vacuum and recirculating the R410A it s responsible of installer to pressurize the whole system with nitrogen using a cylinder with pressure reducer at a pressure above 40 bar gauge Leak test with R410A after opening valves Before opening valves discharge all the nitrogen from the system and create vacuum according to page 36 38 After opening valves check leaks using a leak detector for refrigerant Pump down before disconnecting the refrigerant connections for unit repair removal or disposal Pump down is an operation intended to collect all the system refrigerant in the outdoor unit This operation must be carried out before disconnecting the refrigerant tubing in order to avoid refrigerant loss to the atmosphere gt Shut off the liquid valve with the Allen wrench gt Turn the system on in cooling with fan operating at high velocity Compressor will immediately start provided 3 minutes have elapsed since the last stop gt After 2 minutes of operation shut the suction valve with the
50. r indicator d light Cool indicator 2 F indicator Set temperature indicator On Timer indicator Off Timer indicator good sleep indicator Operation mode indicator Low battery indicator HSITON3 Transmit indicator Air swing indicator Fan speed indicator sh Auto Turbo Low a 7i TIAP m SOng Medium ime Indicator NSAN High AM 0G PM bic When the battery is exhausted 424 will be displayed in the remote controller display When the icon appears change the batteries The remote controller requires two 1 5V AAA type batteries Storing the remote controller When you do not use the remote controller for long time remove the batteries from the remote controller and store it Inserting the batteries 1 Push the lever as arrow indicates on the rear side of the remote controller and pull up 2 Insert two AAA batteries Check and match the 4 and signs accordingly Make sure you have inserted the batteries in correct position 3 Close the cover by place it back to its original position You should hear click sound when the cover is locked properly The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps Note are in the same space If other electrical products operate by the remote controller call your nearest contact center Panama_AQVO9Y _IB amp IM_32445A_E indd 9 9 2011 1 19 16 22
51. r or Off timer indicator and D indicator on the indoor unit m Z Cancel Press the Set Cancel button once again a Additional options available in On timer mode Displays the last mode set before turning the unit off Adjusting fan speed is not available SET qc E You can adjust the temperature in Auto Cool Heat mode Only the latest setting timer will be applied between the On Timer Off Timer Setting on timer and good sleep Off timer functions and off timer simultaneously Follow the same process for setting on timer and off timer NOTE On timer and Off timer setting time should be different from each other e Press the Set Cancel button on the remote controller while timer combination is on Both of the On and Off timer will be canceled and the indicator will disappear 15 Panama_AQVO9Y _IB amp IM 32445A E indd 15 2011 1 19 16 22 49 Using the Smart Saver function This function will set the temperature range limit to help you save energy while the air conditioner is operating in Cool mode Cool Yi E GD aD Lt Hu AM 4 Press the Smart Saver button on the remote controller while the air conditioner is operating in Cool mode gt Smart Saver indicator and air swing indicator appears automatically on the remote controller display The air flow blades move up and down gt Ifthe current set temperature is lower than 24 C it will automatically raise
52. ry it in a well ventilated area 20 Panama_AQVO9Y _IB amp IM 32445A E indd 20 2011 1 19 16 22 59 SCL j i a E Maintaining the air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left in components a CU 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly ner Every 2 Every 3 Every 4 Type Description Ae eee ere Once a year Clean the Full HD filter 1 Clean the condensate drain pan 2 Indoor Tit Thoroughly clean the heat exchanger 2 Clean the condensate drain pipe 2 Replace the remote controller batteries 1 Clean the heat exchanger on the outside of the unit 2 Clean the heat exchanger on the inside ofthe unit 2 Clean the electric components with jets of air 2 Outdoor Verify that all the electric components are firmly e unit tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 e
53. same wrench gt Turn the system off and switch mains supply off b Disconnect tubing After disconnection protect valves and tubing ends from dust gt Compressor damage may occur if run at a negative suction pressure 39 Panama AQV09Y _IB amp IM 32445A E indd 39 2011 1 19 16 23 28 SCL j i Fixing the indoor unit in place Perform the following work on the area where gas leak test was done priorly After checking for gas leaks in the system insulate the pipe hose and cables Then place the indoor unit on the installation plate 1 To avoid condensation problems wrap foam insulation as shown in the figure on a part without insulation on the end of the pipes 2 Wind the pipe assembly cable and drain hose with vinyl tape 3 Place the bundle the pipe assembly cable and drain hose in the lower part of the indoor unit carefully so it does not project from the rear of the indoor unit 4 Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place Make sure pipe does not move when you install the indoor unit on caution a installation plate 5 Wrap the rest of the pipe with vinyl tape 6 Attach the pipe to the wall using clamps optional Fixing the outdoor unit in place Install the outdoor unit in level on a stable base to avoid the generation of noise and vibration especially when installing the unit close to a neighbor
54. se must not Keep a clearance of at least Do not place the end of the be bent 5cm between the end of the drain hose in a hollow drain hose and the ground 34 Panama_AQVO9Y _IB amp IM 32445A E indd 34 2011 1 19 16 23 28 CU a Drain hose installation 1 If necessary connect the 2 meter extension drain hose to the drain hose 2 Ifyou use the extension drain hose insulate the inside of the extension drain hose with a shield 3 Fit the drain hose into 1 of 2 drain hose holes then fix the end of the drain hose m tightly with a clamp 3 G 5 lt Ifyou do not use the other drain hose hole block it with a rubber stopper NOTE Drain hose hole 4 Pass the drain hose under the refrigerant pipe keeping the drain hose Shield tight 5 Pass the drain hose through the hole in the wall Check if it slants Drain h A Extension drain h downwards as seen in the picture HUE AE E The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page Note 39 40 for further details e Make sure the installed direction of the drain hose is correct caution Inadequate installation may cause condensate water leakage If the drain hose is routed inside the room insulate the hose so that dripping condensation does not damage the furniture or floors DO NOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy
55. se when outdoor temperature is extremely low Use an additional heating appliance in combination with the air conditioner if you feel the air conditioner heats insufficiently 10 Panama_AQVO9Y _IB amp IM 32445A E indd 10 2011 1 19 16 22 38 Press the button to turn on the air conditioner Press the button to set the operating mode m Each time you press the Mode button the mode will change in order of Auto Cool Dry Fan and Heat CU a Press the d button to set the desired fan speed Auto sh a Auto Cool SH af Auto Sk Low pp Med SO pg f High Dry SH af Auto Fan SH Low Sag Med Song High Heat SH gf Auto SH Low SR 4 Med pg f High ng o Press the button to adjust the temperature Auto You can adjust the desired temperature by 1 C within the range of 16 C 30 C Cool You can adjust the desired temperature by 1 C within the range of 16 C 30 C Dry Temperature adjustment is not possible Fan Temperature adjustment is not possible Heat You can adjust the desired temperature by 1 C within the range of 16 C 30 C Press the Temp Humi button on the remote controller to check the temperature and humidity level in a room 11 Panama AQVO9Y _IB amp IM_32445A E indd 11 2011 1 19 16 22 40 SCL j i E Adjusting the air flow direction Air flow can be directed to your
56. st the fan speed Remote controller is not e Check if your batteries are depleted working Make sure nothing is blocking your remote controller sensor e Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Timer function does not e Check if you press the Set Cancel button on the remote controller after you have set the set time The indicator is blinking lt Press the Power D button or disconnect the power plug switch off the auxiliary power switch If the indicator is still blinking contact the service center continuously Odors permeate in the e Check if the appliance is running in a smoky area Ventilate the room or operate the air room during operation conditioner in Fan mode for 1 2 hours We do not use smelly components in the air conditioner Clean the Full HD filter if they are dirty Replace the Deodorizing filter if it is dirty 22 Panama AQVO9Y IB amp IM 32445A E indd 22 2011 1 19 16 23 00 TC E PROBLEM SOLUTION Error is indicated e If error indicator such as BM GG GES GES GG Be sia All blink E EE E EN RER QE QE QE QE QE QE QE BE BE BW Be ee EX appears on the indoor unit display contact nearest contact center HSITON3 Noise is generated e Depending on the status of the air conditioner usage noise can be heard when refrigerant flow move
57. the product a Factory refrigerant charge of the product NOTE See unit name plate d b Additional refrigerant amount charged in the field Refer to the above information for the quantity of refrigerant Outdoor unit replenishment g c Total refrigerant charge kg DHO kg d Refrigerant cylinder and manifold for charging Charging the refrigerant under conditions of liquid by using a liquid pipe R410A is a mixed type of refrigerant It is necessary for recharging under conditions of liquid When recharging refrigerant from the refrigerant cylinder to the equipment follow the instructions below 1 Before recharging check whether the cylinder has a siphon or not There are two ways to recharge the refrigerant Cylinder with siphon Cylinder without siphon gt Charge the refrigerant standing the gt Charge the refrigerant turning the cylinder cylinder upright upside down e If R410A refrigerant is charged with gas the composition of the charged refrigerant changes and the characteristics of the equipment vary e During the measuring operation of refrigerant quantity added use an electronic balance If cylinder doesn t have syphon upset it 38 Panama_AQVO9Y _IB amp IM 32445A E indd 38 2011 1 19 16 23 28 Performing the gas leak tests Make sure to check for gas leaks before completing the installation process connecting the assembly pipe and hose between ind
58. to 24 C Cancel Press the Smart Saver button once again Smart Saver function is only available in Cool mode When Smart Saver function is activated temperature range will be limited to 24 C 30 C If the desired temperature is lower than 24 C turn off the Smart Saver function by pressing the Smart Saver button again Temperature Fan speed can also be adjusted see page 11 for instructions If you press the Mode button while the Smart Saver function is on it will cancel the function Using the SPi function SPi Super Plasma ion generates hydrogen H and oxygen Oz to remove a polluted substance and decomposition of such harmful particles It makes you breathe better as if you are staying around waterfalls ocean surf rivers and mountains o e o e SET 4 16 Press the 22 button on the remote controller gt ge indicator will appears on the remote controller display and the air conditioner generates MPI Cancel Panama_AQVO9Y IB8IM 32445A E indd 16 Press the gt button once again The So function can be selected whether the air conditioner is on off 2011 1 19 16 22 51 Using the Auto Clean function Auto clean function will prevent mold from growing by eliminating the moisture inside of the indoor unit Your indoor unit evaporates the moisture inside of the unit Activate this function to provide you with more clean and healthier air Press the Auto Clean b
59. ty may decrease as much as 60 70 of specified capacity according to the using conditions Maintaining your air conditioner Internal protections via the unit control system gt This internal protection operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to against cold air when the heat pump is heating De ice cycle The internal fan will be off to against cold air when the heat pump is heating Anti protection of The compressor will be off to protect internal battery when the air conditioner operates internal battery in Cool mode The air conditioner does not start operating immediately to protect the compressor of Protect compressor l the outdoor unit after it has been started Ifthe heat pump is operating in Heat mode De ice cycle is actuated to remove frost from an outdoor unit that may NoTE have deposited at low temperatures The internal fan is switched off automatically and restarted only after the de ice cycle is completed 6 Panama_AQVO9Y _IB amp IM_32445A E indd 6 2011 1 19 16 22 24 SCL j i E Checking the name of the parts Your air conditioner may slightly look different from illustration shown above depending on your model Main parts HSITON3 Room temperature sensor NG Es Pang ee Air flow blade U dd left and right a Air flow blade SPi indicator
60. utton When the air conditioner is turned off HSITON3 gt The Auto clean indicator on the indoor unit display appears and the Auto cleaning function runs When the air conditioner is turned on gt After stopping the air conditioner operation the Auto clean indicator on the indoor unit display appears and the Auto cleaning function runs X Auto Clean time can vary depending on the previously used mode Auto cool Cool Dry mode approximately 30 minutes Auto heat Heat Fan mode approximately 15 minutes Cancel Press the Auto clean button once again The Auto clean indicator appears only on the indoor unit display as NOTE Clean lt When the air conditioner is turned on the Auto clean function runs after stopping the air conditioner operation Using the d light Cool function The sensor in the indoor unit which measures temperature and humidity in a room keeps the room temperature in the most comfortable level by controlling the temperature and the fan speed automatically Press the d light Cool button on the remote controller while the air conditioner is operating in Cool mode gt d light Cool indicator and air swing indicator appears automatically on the remote controller display gt The air conditioner will set the fan speed to auto and adjust the temperature automatically according to the room temperature and humidity Cancel Press the d light Cool button once again
61. y or property damage a Unplug the power plug from the a Follow directions ala ted S Do NOT attempt Q Do NOT disassemble Make sure the machine is grounded to prevent electric shock FOR INSTALLATION WARNING O Plug the power cord into a wall socket with the power specifications of the product or higher and use the socket for this appliance only In addition do not use an extension cord gt Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire gt Do not use an electric transformer It may result in electric shock or fire gt Ifthe voltage frequency rated current condition is different it may cause fire The installation of this appliance must be performed by a qualified technician or service company gt Failing to do so may result in electric shock fire explosion problems with the product or injury Install a switch and circuit breaker dedicated to the air conditioner gt Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed gt Failing to do so may result in electric shock or fire S Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where

Samsung AQV09YWBAN User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents