Samsung MCM-A100 User Manual
Contents
1. View of the Function Controller The tunction controller is an additional controller which is used with the centralized controller Operating mode Removing frost indicator Centralized controller indicator Except Cooling Only Models Communication error indicator L s i iS Temperature setting Roomnumberdisplay B B 4 B B Fan speed Number est FILTER SIGN SIGN Air flow direction Test indicator Filter Sign indicator On Off amp Timer Set Cancel button On Off indicator Fan speed adjustment button Temperature adjustment buttons Indoor unit selection button Swing button Except Duct Type Test button Filter Reset button Mode selection button Mote Test button is for your installation specialist You must NOT press it After cleaning the air filter press the filter reset button Then the wired remote controller will display the FILTER SIGN indicator when the time to clean the air filter Duct type air conditioner does not have function of adjusting air flow direction Therefore the function is not operated even if you press the swing button 2 9 gt Getting Start You have just purchased a function controller and it has been installed by your installation specialist Your Owner s Instructions contain much valuable information using your function controller Please take the time to rea2. Stopped It will start up normally after three minutes 2 Toselectthe HEAT mode press the Mode button until m is displayed at the top of the function controller ic SUPT ea Result air conditioner runs HEAT mode Note You change modes at any time 3 Toadjustthe temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 16 and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts heating provided that the room temperature is lower than the selected temperature the fan will however operate gt e E ic 4 Select the fan speed by pressing the Fan button or more times until the intended value is displayed ea Automatic rotated p gt gt ful 45 Low Medium High 5 Tocontrolthe direction of the air flow refer to page 15 ale 9 Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 Ifnecessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air co
3. OWNER S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D UTILISATION ISTRUZIONI PER LUS0 MANUAL DE INSTRUCOES GEBRAUCHSANWEISUNG gt Function Controller MCM A100 System Air Conditioner Aire acondicionado sistem tico Climatiseur num rique multifonctionnel Sistema Aria Condizionata Sistema Ar Condicionado Klimaanlage System gt DB98 05164A 2 RUSSIAN EAAHNIKA DEUTSCH PORTUGU S ITALIANO FRAN AIS ESPA OL ENGLISH Safety Precautions e Before using the function controller read carefully this instructions e After reading the instructions keep this owner s instructions and the installation manual in a handy and safe place lf a user is changed you must hand over the manuals e Never attempt to install the air conditioning system or to move the function controller by yourself Do not attempt to install or repair this function WARNING controller by yourself This function controller contains no user serviceable parts Always consult authorized service personnel for repairs When moving consult authorized service personnel for disconnection and installation of the function controller Ensure that the wall is strong enough to support the weight of the function controller Must install the function controller with rate
4. ction mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Toselectthe AUTO mode press the Mode button until ab is displayed at the top of the function controller Result The air conditioner runs in AUTO mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts cooling provided that the room temperature is than the selected temperature The quantity of air is adjusted automatically Cooling Your Room You must select the COOL mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged Stopped It will start up normally after three minutes 2 Toselectthe COOL mode press the Mode button until is displayed at the
5. d power supply In the event of a malfunction burning smell etc immediately stop operation turn off the electrical breaker and consult authorized service personnel Do not use inflammable gases near the function N CAUTION controler Do not spill water into the function controller Do not operate the function controller with wet hands Do not install the function controller in a location where it will come into contact with the combustible gases machine oil sulphide gas etc Do not press buttons with a pointed thing Do not pull or bend the function controller cable excessively Do not use this function controller for other purpose Do not spray an insecticide or other combustible things on the function controller Do not clean the function controller with benzene solvents or other chemicals Do not give a shock to the function controller or disassemble it by yourself Contents VIEW OF THE FUNCTION CONTROLLER l 4 9 GETTING START cee ott 5 SELECTING THE INDOOR UNIT 55555 55 5 6 SELECTING THE AUTOMATIC OPERATING gt gt gt 7 COOLING YOUR ROOM eee 8 HEATING YOUR 222525222222 10 10 Except CooLING ONLY MopEts PREMOVING EXCESS HUMIDITY 12 AIRING YOUR 0 25552522 5 14 ADJUSTING THE AIR FLOW DIRECTION 15 Except Duct x Co 9 Z
6. d them as they will help you take full advantage of the unit s features In the main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols PRESS PUSH HOLD DOWN Selecting the Indoor Unit You can control a specific indoor unit from the function controller 1 Select an indoor unit you want to control by pressing button Result time you press button the room number is increased by 1 and each time you press button the room number is decreased by 1 from 0 15 2 Turn the air conditioner on by pressing ON OFF button Result On Off indicator the function controller comes on The air conditioner runs in the mode selected when the unit was last used 3 Select an appropriate operating mode by pressing Mode button Result The air conditioner runs in the selected mode Note For further details on operating modes refer to page 7 15 Selecting the Automatic Operating Mode ac 9 the Automatic mode the room temperature and the fan speed are controlled automatically 1 If necessary press button Result On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a prote
7. e press the Mode button until 5 is displayed at the top of the function controller Result The air conditioner runs FAN mode Note You can change modes at any time 3 Selectthe fan speed by pressing the Fan button one or more times until the intended value is displayed Low Medium Sail High 4 Tocontrolthe direction of the air flow refer to page 15 Adjusting the Air Flow Direction Except Duct ac 9 21 9 a Depending the position of the indoor unit you adjust the position of the air flow blade thus increasing the efficiency of the air conditioner 1 Press the Swing button Result The blade is moving between up and down V PORTANT When the air conditioner is first turned on the blade is moved 2 To stop the blade press the Swing button again To set to the required position press the Swing button again when the blade is in the required position THIS AIR CONDITIONER IS MANUFACTURED BY ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR CE CLIMATISEUR EST FABRIQUE PAR QUESTO CONDIZIONATORE D ARIA PRODOTTO DA ESTE APARELHO DE AR CONDICIONADO E FABRICADO POR DIESE KLIMAANLAGE IST FABRIZIERT VON AYTH 2Y2KEYH KATA2KEYA2THKE ANO 7 ELECTRONICS Printed in Korea
8. nditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged It will start up normally after three minutes 2 Toselectthe DRY mode press the Mode button until is displayed at the top of the function controller Result The air conditioner runs in DRY mode Note You change modes at any time ac 9 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts removing the excess humidity The quantity of air is adjusted automatically 4 Tocontrol the direction of the air flow refer to page 15 Airing Your Room If the atmosphere in your room is stale you can air it using the FAN feature 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged Stopped It will start up normally after three minutes 2 select the FAN mod
9. top of the function controller Result The air conditioner runs in COOL mode Note You change modes at any time ale 9 3 Toadjustthe temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however operate 4 Selectthe fan speed by pressing the Fan button one or more times until the intended value is displayed s I Automatic rotated 25 gt gt hal DAP Low Medium High 5 Tocontrolthe direction of the air flow refer to page 15 Heating Your Room Cooling Only Models You can select the HEAT mode only in heat pump models You must select the HEAT mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press ON OFF button Result On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in
Download Pdf Manuals
Related Search