Home

Samsung AP30M0AN User Manual

Contents

1. 1 Open the panel and pull out the air filter after removing the tape that holds the air filter Pull out the air filter in the direction of the arrow as shown in the below figure 2 Clean the air filter with a vacuum cleaner or in running water If dust is too heavy use warm water mixed with detergent Do not scrub the filter too hard since it may get damaged 3 Dry the air filter in a ventilated area Do not dry the air filter in a place with direct sunlight 4 Insert the air filter back in its original position Make sure it is firmly fixed B Clean the air filter every two weeks Cleaning term may differ depending on usage and environmental conditions NOTE 21 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 21 2015 01 05 5 11106 Cleaning and maintaining the air conditioner l Maintaining your air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and turn off the circuit breaker There may be internal damage if moisture is left in components 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly Type Descrip
2. Cancel gt Press the Timer button gt Select On gt Press the lt or gt button gt Set the time to gt Press the SET button gt Press the Power button Remote controller display Additional options available in On timer You can select from Auto gt Cool gt Dry gt Fan gt Heat You can set the temperature after selecting the operation mode Temperature adjustment is available when Auto Cool Dry Heat mode is selected B After 3 seconds from the completion of the On timer setting only On indicator will remain on the remote controller display e You cannot set the fan speed when setting the On timer Ifyou press the Power button on the indoor unit after setting the On timer function with the remote controller Timer indicator m on the indoor unit display will disappear and the function will be canceled However On indicator on the remote controller will remain on but the function will not work NOTE 17 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 17 2015 01 05 5 11103 Setting the On Off timer When the air conditioner is on 1 Press the Timer button to select Off Off indicator starts to blink and you can set the time 2 Press the lt or gt button to set the time You can set the time in 0 5 hour unit from 0 5 3 hours and 1 hour unit from 3 24 hours Time can be set from minimum 0 5 hours to maximum 24 hours 3 Press the SET button
3. signs and insert them in correct position Close the battery cover Match the cover and bottom part of the remote controller and press it until you hear click sound v vN v A Make sure that water is not allowed to enter the remote controller CAUTION B There is a possibility that the air conditioner will not operate by remote controller near strong light such as a fluorescent lamp or neon sign In this case use the remote controller in front of the remote controller receiver of the indoor unit Ifother electrical products are operated by the remote controller call your nearest service center NOTE 13 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 13 2015 01 05 5 11100 Basic operation Basic operation is an operation mode that can be selected by pressing the Mode button l Auto In Auto mode the air conditioner will automatically set the Operation Cool Heat Mode and fan speed depending on the room temperature detected by the room temperature sensor Heat mode is applicable to AP30M1 gt model only Cool Cool mode is frequently used and you can freely control the temperature fan speed and air flow direction in cool mode Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air The Dry mode will provide you with fresh air even on a rainy day gt Outdoor unit will repeatedly and automatically turn on off for maximum dehumidification according to the temperature diff
4. When installing the outdoor unit near seashore make sure it is not directly exposed to sea breeze If you can not find a adequate place without direct see breeze protection wall should be constructed HSII N3 Yy Yy VY VY VY VY VY gt Install the outdoor unit in a place such as near buildings etc where it can be prevented from sea breeze which can damage the outdoor unit Outdoor uu Outdoor unit OU uo Sea breeze m 00 Sea breeze m oo i0 ool Sea Sea gt Ifyou cannot avoid installing the outdoor unit by the seashore construct a protection wall around to block the sea breeze Protection wall Outdoor unit Protection wall should be constructed with a solid material such as oo concrete to block the sea breeze and the height and the width of the Sea breeze gt Oo wall should be 1 5 times larger than the size of the outdoor unit Also 00 secure over 700mm between the protection wall and the outdoor unit Sea for exhausted air to ventilate gt Install the outdoor unit in a place where water can drain smoothly If you cannot find a place satisfying above conditions please contact manufacturer Make sure to clean the sea water and the dust on the outdoor unit heat exchanger and spread corrosion inhibitor on heat exchanger At least one time per one year Choose a place where there is no direct sunlight Choose a place where it could not come into contact with snow and rain
5. gt Keep the children away from the air conditioner to prevent them from putting their finger on the air conditioner Potential risk of personal injury Ensure no water gets into the air conditioner gt Potential risk or electric shock gt Ifthe water gets into the air conditioner stop and unplug the power source immediately Turn off the air conditioner using the provided remote controller or control accessory if provided Do not unplug to turn off the unit unless there is an immediate danger Do not run the air conditioner for an extended period of time in a room with the door closed or with babies elderly or disabled people gt Open the door or windows to ventilate your room at least once an hour to prevent oxygen shortage The air conditioner is composed of moving parts Keep children away from the unit to avoid physical injury Make sure that children take precautions against access to the air conditioner and they do not play with the unit Do not clean the interior of air conditioner on your own gt You may damage the parts which can cause electric shock or fire gt Consult contact center for cleaning the interior of the air conditioner HSII N3 Do not connect the air conditioner with heating apparatus or attempt to disassemble remodel or repair it by yourself gt Potential risk of malfunction electric shock or fire If repairs are needed consult the contact center Consult the place of purchase or co
6. Be sure to perform the test operation after installation It is easy to start the test operation in winter if you increase the sensor temperature to 23 C 25 C by holding the indoor temperature sensor Cooling operation When the outdoor temperature is below zero do not test operation for more than 3 minutes Otherwise the compressor will be damaged CAUTION Temperature sensor l Pump down procedure When removing the product Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes Release the valve caps on High and Low pressure side Use L wrench to close the valve on the high pressure side Approximately 2 minutes after close the valve on the low pressure side Stop operation of the air conditioner Disconnect the pipes OW a Oe Noes 47 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 47 2015 01 05 2 5 11116 Packing and unpacking guide Indoor unit lt Cushion top amp Cushion mid Packing case 3 gt 77 7 7N M Indoor unit P lt Cushion bottom gt Packing the unit as below procedure 1 Put the indoor unit onto the cushion bottom Assemble cushion mid 2 of indoor unit Put the cushion top onto the indoor unit Put the packing case 3 from the top of set Seal the packing case 3 Oho te gt Unpacking the unit as below procedure Take out the packing case 3 fr
7. N3 Main parts Air flow blade up down orientation Air flow blade right left orientation Air outlet Ie Control panel Air filter lo open the panel gt Hold the upper part of the panel then pull it slightly forward A Don t open the panel when it is operating It may cause a malfunction or an electrical hazard CAUTION Remote controller slot B Your air conditioner may slightly look different from illustration shown above depending on your model NOTE Mirage_AP30M0 _IBIM_EN_05320A 00 indd 9 2015 01 05 5 10159 Viewing your air conditioner Control panel You can operate the air conditioner with the control panel when you can t or don t want to operate the air conditioner with the remote controller see pages 20 Air swing Up Down indicator Fan speed indicator Air swing Left Right indicator Defrost indicator Defrost is applicable for AP30M1 model only Temperature setting Operation mode indicators Heat is applicable for AP30M1 model only Timer indicator re Mode selection button S Saver indicator 5 Ss PUY e pea 1 ke ID Fi D wi Turbo button Air swing Up Down button Power 4 button Air swing Left Right Temperature button adjustment buttons Fan speed adjustment button Long function indicator Remote controller receiver Lock indicator Outdoor unit operation indicator Turbo indicator Bi Heater and Pu
8. 100cm 31 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 31 2015 01 05 2 5 11108 Selection of installation place Outdoor unit A place free from the risk of combustible gas leakage A place which can bear the weight of the unit A place which can bear the fixing strength of the outdoor unit Avoid a place subject to oil including machine oil Avoid a saline place vvvvvy Avoid a place subject to sulfide gas hot spring zone When installing the unit at such special environmental conditions it may cause machine trouble When it is unavoidable to use such places It requires special maintenance gt A place where the discharge air and noise of the outdoor unit do not disturb the neighborhood Take special care not to cause any inconvenience to your neighbors when installing the unit on the borderline with your neighborhood gt A place where strong wind does not head against the air outlet of the outdoor unit If a strong wind heads directly against the air outlet at the time of cool operation a safety device can be operated gt Donotinstall the outdoor unit at an unstable place such as outer wall of an apartment or building The outdoor unit may fall down causing severe personal or property damage or loss _ If there is any unavoidable reason to install the unit at such a place take the following measures against the wind 1 When installing the unit at a roadside concentrated with buildings install it parallel
9. Choose a place where flammable gas does not leak Choose a place where the indoor and outdoor unit can be connected with a pipe vvv v 33 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 33 2015 01 05 5 11109 Preparing the installation After installing the outdoor unit apply rust inhibitor on the internal pipes and heat exchanger warning lf yOu don t apply rust inhibitor airborne corrosive gas such as sulfur compounds hydrogen sulfide and ammonia and salty dust may cause pipe corrosion which will lead to refrigerant leakage Inspect the outdoor unit at least once a year and re apply the rust inhibitor where it is damaged worn out When applying the rust inhibitor please be aware of the following Turn off the power before spraying the rust inhibitor Wear protective goggles and mask before spraying Clean the dusty surface with clean fabric or paper before spraying Make sure that wind is blowing from worker s back when spraying Do not spray on the PCB panel and electric parts A Install the indoor unit away from any interfering sources such as radio computer stereo equipment and also select caTiON the place where the electrical wiring work can be possible Especially keep the unit at least 3m away from the electrical equipment in an area electromagnetic waves generated and install the protection tube to protect the main power cable and communication cable Make sure that there is no equipment electrom
10. Timer Turbo WF E NS Cancel gt Press the Options button and then lt gt or Options button to make the Long indicator blink and press the SET button You cannot select the Long function and the Turbo function simultaneously nore You can only adjust horizontal left and right air swing You cannot adjust the fan speed You cannot set the Long function while operating in Dry Fan mode Remote controller display 19 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 19 2015 01 05 2 5 11104 Locking the control panel You can lock the control panel on the indoor unit to prevent the children from playing with the air conditioner Press the Temp V and buttons for 3 seconds gt You will hear ring and the Lock fal icon will appear on the indoor unit display gt Once Lock is set you cannot control the air conditioner with the control panel but Y ake you can only control it with the remote controller Therefore this function will be WS Wp useful to keep the children away from touching the control panel gt Tounlock the control panel press the Temp and buttons again for 3 seconds Using the air conditioner with the control panel You can control the air conditioner without the remote controller 1 Press the Power button on the indoor unit control panel gt The air conditioner will turn on with ringing sound Stop To turn off the air conditioner press the Power button again 2 Press th
11. any objects especially containers with liquid HSII N3 YY Do not touch the pipe connected to the air conditioner Install the indoor unit away from lighting apparatus using the ballast gt Ifyou use the wireless remote controller reception error may occur due to the ballast of the lighting apparatus Install the outdoor unit where operating noise and vibration will not disturb your neighbor and in a well ventilated area with no obstacle gt Potential risk of malfunction gt Operating noise may disturb your neighbor Make sure that there are no obstacles or covers that block the air conditioner Allow sufficient space for air circulation gt Insufficient ventilation may result in poor performance If the power cable is damaged the manufacturer or a qualified service technician must replace it If a power outage occurs while the air conditioner is working turn off the power source immediately Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Check for damage on delivery If damaged do not install the air conditioner and call the place of purchase immediately Keep indoor temperatures stable and not extremely cold especially where there are children elderly or disabled people The packaging material and used batteries of the remote controller optional must be disposed of in accordance with the national standards The refr
12. cor With its soft color and latest design the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically Mirage_AP30M0 _IBIM_EN_05320A 00 indd 2 2015 01 05 5 10158 Contents User manual Safety precautions sates meee ais asi 3533 va sait0t0tagai 4 Viewing your air conditioner 9 Checking the remote controller 5 2221 0c 6x 6 biet DEbpbsbsbei4s44434555144g35 602 3 5533395353539441 9602580108 c g 11 m Basicoperation 2222 22442 604 00630 022 000 8562 ETETE FETEI EEEE ii 8 42 E EEEE EETA x41444840443503535 09090 00148 4 4 Setting the On Off UMET iia onnios ses caveeeseseresa tanita EEEE E EEE En E STEDINNI EE ERE ENARA 17 2 Using the Turbo MNCtiON seieren ATETA EE ENEN E buanaguanauenbibinansassosnagsaas teers vanes 19 Using the Long MUNCtiON 1s t ng b 0 c3 946s15 c u L ti t E 0a 34a 3162804655535336334 92 5518 S45 cmlA gg Locking the control panel aioe Sk Using the air conditioner with the control panel Cleaning and maintaining the air conditioner Appendix Installation manual Safely PreCaUliONs 2 5 210 2522061 E 408148 1005 t1 8500 03 8680 1500 1101 81029280 05a38 168270051581511 51a 121 s0 Accessory Parts list ae sssss3z2gi6d ga aa E A R REE E N Selectionsof installation Place 42 53 45 sccecainecestencanaseadneedsaaugeeuadacasariensi E n a EN EAA R Preparing the installation 4z2 4 sxsassscaS6iies19ggSn
13. than 10m Less than 6m s amp o b ty 4 Install the high pressure pipe to the heat exchanger liquid pipe and the low pressure pipe to the heat exchanger gas pipe respectively using the flare nut taking care not to cause any leakage of refrigerant 5 Be sure to insulate the pipe with appropriate insulation material Refer to page 40 6 Insert the extension drain hose to the drain connection port tightly then fix them with a cable tie or a tape to prevent any water leakage see page 43 7 After completion of the installation check the connecting area for any gas leakage 8 Wind a finish tape when the wiring of the refrigerant pipe the unit and the drain piping are completed 9 Fix the piping and drain hose by using the indoor unit piping holder Outdoor unit checking area Indoor unit piping holder Indoor unit checking area 39 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 39 2015 01 05 5 11412 Installation method Refrigerant pipe work Insulating the pipes gt Make sure to insulated the refrigerant pipes with an insulation tape If the pipe is not insulated condensate may form and drop into the indoor Pipe insulator Vinyl gt Wind the refrigerant pipes and the drain hose with vinyl tapes Indoor tape gt When you bend the pipe try to secure large bending radius over 100 mm outdoor unit to prevent the copper pipe from distorting communication gt U
14. vary depending on the amount of frost on the outdoor unit In snowy or rainy days Defrost operation cycle may be shorter due to humidity You cannot control the air conditioner with the remote controller while Defrost operation is on Try to control the air conditioner after Defrost operation is complete NOTE 14 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 14 2015 01 05 5 11100 l Turning on the power Press the button to turn on the air conditioner l Selecting the operation mode Auto utton to set the operation mode HSII N3 Auto Pill Auto Eoo Auto Med High amp Turbo pry Auto Fan F Med High P Turbo Heat Auto Med High Turbo l Adjusting the desired temperature Temp Press the button to adjust the desired temperature Auto Temperature can be adjusted by 1 C within the range of 18 C 30 C Cool Temperature can be adjusted by 1 C within the range of 18 C 30 C Dry Temperature can be adjusted by 1 C within the range of 18 C 30 C Fan Temperature cannot be adjusted Heat Temperature can be adjusted by 1 C within the range of 16 C 30 C Mirage_AP30M0 _IBIM_EN_05320A 00 indd 15 15 2015 01 05 2 5 11101 Basic operation l Selecting air flow direction This function allows you to shift the air flow direction up and down or left and right Press th
15. with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries 26 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 26 2015 01 05 5 11107 gt Our units must be installed in compliance with the spaces indicated in the manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs The units components must be accessible and that can be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the manual the cost necessary to reach and repair the unit in safety as required by current regulations in force with slings trucks scaffolding or any other means of elevation won t be considered in warranty and charged to end user Power supply line fuse or circuit breaker HSII N3 gt Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards gt Always verify that a suitable grounding connection is available gt Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines gt Always verify that the cut off and protection switches are suitably dimensioned gt Verify that the air cond
16. with the road 2 Install the unit so that the air outlet faces toward the wall at a place such as rooftop which may be subjected to strong wind 2 Strong wind yepnouly gt The outdoor unit should be installed in accordance with the service space More than 50cm Space for piping and wiring oo More than 30cm The air intake faces toward the wall 32 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 32 More than 50cm 756 Space for piping and wiring ore than 30cm More than 60cm 9 O8 08008929 O8 920 O 8008 929 O8 o9 Oo 90098O O09 FOO 0 9009 8D Oo 090 The air outlet faces toward the wall 2015 01 05 5 11109 Preparing the installation l Selecting appropriate location for installation Decide the installation location based on the following condition and obtain the user s approval gt Avoid a place that may disturb your neighbor Noise may occur from the outdoor unit and the discharged air may run into the neighborhood Be careful of the operation time in a residential area Install the outdoor unit on a hard and even area that can support its weight Choose a flat place that rainwater does not settle or leak Choose a place avoiding strong winds Maintain sufficient space for repairs and service Choose a place where you can easily connect the pipes and cables to the indoor unit Make sure that the condensed water dripping from the drain hose runs out properly and safely
17. 5 5 11114 Check and test operation l Check gt Be sure to check the following again after completion of installation 1 Check the piping connection area for any gas leakage Indoor connection area Outdoor connection area 2 Is the drain hose properly connected 3 Is the insulation of the piping in good condition Pipe insulator Over 7mm foamed polyethylene or EPDM foam Pipie connection part insulator Over 5mm foamed polyethylene 4 Is grounding properly made 46 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 46 2015 01 05 2 5 11116 Test operation gt After checking read the owner s instructions carefully and perform a test operation Then deliver the unit to the customer When delivering the unit be sure to read carefully and follow the contents of the owner s instructions gt Check if the indoor outdoor unit s connection wires are properly connected 1 Turn on the air conditioner and select Cool mode Test is only available in cooling operation Check if the cool air comes out from the indoor unit Check if the fan of outdoor unit rotates HSII N3 2 Ifthe units don t work as above check if the indoor outdoor unit s connection wires are properly connected The connection wires should be properly connected to the correct terminal number A 1 Be sure to check whether the service valve is open before attempting to perform the test operation 2
18. A 00 indd 18 2015 01 05 5 11108 Using the Turbo function You can set the Turbo function to provide fast and powerful cooling heating When the air conditioner is operating in Cool or Heat mode 1 Press the Turbo button Turbo will be displayed and the function will operate for 30 minutes HSII N3 Cancel P Press the Turbo Button B Turbo function is only available in Auto Cool Heat mode and the air conditioner will return to its previous operation mode after operating for 30 minutes in this function Heat mode is applicable for AP30M1 gt model only Air flow direction can be adjusted Temperature and fan speed cannot be adjusted Ifyou select the Turbo function while Long Single user function is on corresponding function will be cancelled You can also turn on off the Turbo function with the Options button 1 Press the Options button 2 Press the lt gt or Options button until Turbo indicator starts to blink 3 Press the SET button to set the Turbo function NOTE Remote controller display Using the Long function Long function will be helpful when you want the cool air to go to much further place 1 Press the Options button 2 Press the lt gt or Options button until Long indicator starts to blink 3 Press the SET button to set the Long function Long will blink first then remain on the display as Long and the function will begin ly 9 W S A A A
19. AP30M0 _IBIM_EN_05320A 00 indd 42 2015 01 05 2 5 11118 l Drain hose 1 Connect the drain hose by inserting the extension drain hose to the drain connection port tightly 2 Insulate the extension drain hose then fix it with a cable tie or a tape Vinyl chloride ipi i ping Inner diameter 13 mm Insulation Foamed polyethylene Drain hose Drain hole for duct polypropylene Insulation foamed polyethylene Connecting drain hose HSII N3 e As the draining is of natural drain type make the drain hose direct downward caution Fix the drain hose tightly to prevent any water leakage Ifthere is any foreign substance in the drain plate it may clog the drain pipe Therefore be sure to remove the foreign substance inside after installation Do not extend the drain hose l Fixing the indoor unit gt lfthe indoor unit is installed on unstable place it may shake or fall down To prevent these accidents you must fix the top of the indoor unit tightly with fixing brackets Wall installation Example 1 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 43 Corner Installation 43 2015 01 05 2 5 11114 Air purge Be sure that all valve cocks are closed gt The airin the indoor unit and in the pipe must be purged Make sure to vacuum inside of the connection pipe using vacuum pump after connecting pipes Use vacuum pump as shown at the figure If air re
20. Set temperature or on off set time with the timer function On Off timer Fan speed Air flow direction Options These functions are not supported le B Single Heater and Purity functions are not supported by this model NOTE Using the remote controller Point the remote controller towards the remote controller receiver of the indoor unit see page 10 to find the location of remote controller receiver When you properly press the button on the remote controller you will hear ring sound from the indoor unit B The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps nore are in the same space Ifother electrical products operate by the remote controller call your nearest contact center 12 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 12 2015 01 05 5 11100 Battery changing time When the battery is exhausted 4 will be displayed in the remote controller display When the icon appears change the batteries The remote controller requires two 1 5V AAA type batteries Storing the remote controller When you do not use the remote controller for a long time remove the batteries from the remote controller and store it in the remote controller holder HSII N3 Inserting the batteries Open the battery cover Push the part in the direction of the arrow and lift up the cover Insert the batteries Check and match the
21. This product is not manufactured for Iran SVC Warraty will not be applicable and the user will be responsible for service xpenses when the product is used in lran QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT UAE 800 SAMSUNG 800 726 7864 OMAN 800 SAMSUNG 726 7864 www samsung com ae support English KUWAIT 183 CALL 183 2255 www samsung com ae_ar support Arabic BAHRAIN 8000 4726 EGYPT 08000 726786 eu 16580 www samsung com eg suppo JORDAN cae Levant t English www samsung com Levant support Englis 06 5777444 3 PP 9 MOROCCO 080 100 22 55 www samsung com n_africa support SAUDI ARABIA 920021230 www samsung com sa support www samsung com sa_en support English TURKEY 4447711 www samsung com tr support Mirage_AP30M0 _IBIM_EN_05320A 00 indd 52 2015 01 05 2 5 11117 AP30MO Series AP30M1 Series 100 Recycled Paper imagine the possibilities Thank you for purchasing this Samsung product DB68 05320A 00 et Mirage_AP30M0 _IBIM_EN_05320A 00 indd 53 2015 01 05 2 suhe Features of your new air conditioner Strong Turbo Long Function Your new air conditioner supports Turbo function which makes you cool fast for 30 minutes and Long function which makes the cool air goes to much further place Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d
22. Water is dripping from the air flow blades Check if the air conditioner has been cooling for an extended period of time with the air flow blades pointed downwards Condensation may generate due to the difference in temperature Remote controller is not working Check if your batteries are depleted Make sure batteries are correctly installed Make sure nothing is blocking your remote control sensor Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Smoke is generated from the outdoor unit It may not be a fire but it can be a steam generated by the defrost operation from outdoor heat exchanger during Heat mode in winter Error is indicated Contact the service center when the following errors are indicated El l EI 22 EI 5H El 62 EI B3 E2 31 4 9 24 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 24 2015 01 05 5 11107 Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table HSII N3 for efficient use OPERATIONAL TEMPERATURE INDOOR MODE IF OUT OF CONDITIONS INDOOR OUTDOOR HUMIDITY Condensation may occur on the indoor COOLING 18 C to 32 C 21 C to 52 C 80 or less unit with risk to have either water blow off or drops on the floor HEATING 27 C or less 5 C to 24 C Internal protec
23. ach of children gt Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires gt Do not place containers with liquids or other objects on the unit gt All the materials used for the manufacture and packaging of the air conditioner are recyclable gt The packing material and exhaust batteries of the remote controller optional must be disposed of in accordance with current laws gt The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely Installing the unit IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines Always disassemble the electric lines before the refrigerant tubes gt Upon receipt inspect the product to verify that it has not been damaged during transport If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer gt After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user gt Donotuse the air conditioner in environments
24. age_AP30M0 _IBIM_EN_05320A 00 indd 44 2015 01 05 2 5 11114 Refrigerant charging How to add refrigerant Connect manifold gauge to the gas side service valve Take the trial operation with the cooling trial operation mode na Perform trial operation for longer than 10 minutes and add refrigerant based on the below pressure table Z Purpose of pressure table If additional refrigerant filling is needed due to the leakage of the refrigerant or re installation amp add refrigerant using pressure table Pressure table for temperatures AP30M0A gt Pressure table for temperatures AP30M1A gt Cooling operations gt Cooling operations Outdoor temperature C Outdoor temperature C 21 35 43 52 21 35 43 52 Indoor temperature C Indoor temperature C 21 42 4 6 4 8 5 2 21 4 0 4 6 4 9 5 3 27 4 7 5 2 5 4 5 8 27 4 3 5 1 5 5 5 9 32 5 2 5 7 6 0 6 4 32 4 6 5 6 6 1 6 5 4 Check the stability of the pressure for 10 minutes Gas side Liquid side 5 After adding refrigerant fasten cap nuts firmly Always use R 22 refrigerant to avoid damage of the unit or an explosion caution Must keep the quantity of refrigerant by using a balance Do not use a manometer or not depend on your experiences 45 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 45 2015 01 0
25. agnetic waves generate If not malfunction of the control system may occur due to the effect of the electromagnetic wave For example The remote control sensor of the indoor unit may not be received well of electronic lighting style fluorescent lamps such as fluorescent lamps are in the same space when using a remote control Make sure to install the outdoor unit in a safe place where snowfall will not be obstructed The frame should be installed in a place where the air inlet and heat exchanger of the unit are not buried in the snow Aventilation system may be required in the case the outdoor unit is installed in a closed space or room even though R 410A is not poisonous or flammable Install the railing around the outdoor unit to prevent falling when the unit is installed at high place of roof on the building Avoid installing the units in places such as an exhaust pipe and ventilating opening exposed to corrosive gas oxides of sulfur ammonia gas or sulfur gas herbicides These places need additional anticorrosive treatments Please contact manufacture to avoid corroding copper pipes or soldered parts According to the condition of power supply electric noise or unstable voltage can occur malfunction of electric parts or control system At the ship or places using power supply from electric generator etc l Space requirements gt The space suggested below is based on operating condition of outdoor temperature of 35 C If op
26. ditioner gt Potential risk of personal injury If failure or damage occurs on the conditions of improper use not followed by the manual there will be an extra labor charge for installing and construction gt Potential risk of malfunction electric shock or fire if repairs or installations are attempted by a non qualified service technician Do not spray flammable gases such as insecticide near the air conditioner gt Potential risk of electric shock fire or unit malfunction Do not open the front panel during operation gt Potential risk of electric shock or unit malfunction Cool air should not flow directly towards people pets and plants gt Itis harmful to your health pets and plants Do not drink drain water coming out of the air conditioner gt Potential risk of health hazard Do not allow children to climb on the air conditioner Do not use the air conditioner as a cooling precision instrument for food pets plants cosmetics or machinery Mirage_AP30M0 _IBIM_EN_05320A 00 indd 6 2015 01 05 5 10159 Do not pull or give excessive shock to the air conditioner gt Potential risk of fire or unit malfunction and there are risk of personal injury because unit may fall down Do not spray water directly on the air conditioner or use benzene thinner or alcohol to clean the surface of the unit gt Potential risk of electric shock or fire gt Potential risk of damage to the air conditioner Do not place
27. e R Outdoor unit 12 70 25 and over 1 15 88 32 and J Oil trap 19 05 38 oe a EA Gas side pipe c Insulation E Install it at every 22 23 41 and over 10m 25 40 51 and over 28 60 57 and over A Branch joint Cut on insulation 31 75 60 and over gt Height of the oil trap H 4R lt H lt 6R 1 Indoor unit 40 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 40 2015 01 05 2 5 11112 l Connection of refrigerant piping Flare processing 1 Cut the pipe using the pipe cutter 2 Remove burr on the edge of pipe If burr is not removed after cutting the pipe there is a risk of refrigerant gas leakage Ifforeign substance such as burr goes into the pipe there is a risk of product breakdown Oblique Face the pipe downward when doing the work Rough 3 Insert the flare nut into the pipe and then perform the flare processing Burr HSII N3 Pipe S Reamer Y Outer diameter D mm A mm 06 35 13 15 88 22 A U x Correct Inclined Damaged surface Cracked Uneven thickness When installing make sure there is no leakage When recovering the refrigerant ground the compressor first before CAUTION removing the connection pipe If the refrigerant pipe is not properly connected and the compressor works with the service valve open the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high It may cause ex
28. e Temp V and button to adjust the temperature gt You can increase decrease the temperature by 1 C 3 Press the Fan Speed lt button to adjust the fan speed gt Each time you press the Fan Speed button the fan speed will change in order of Medium High Turbo 3 s and Auto 4 e 4 Press the Mode button to select the operation mode You can select operation mode you want by pressing the Mode button gt Each time you press the Mode button the mode will change in order of Auto Cool Mos Dry Fan and Heat Heat mode is applicable for AP30M1 model only v 5 Press the Turbo g button to select Turbo mode 6 Press the Vertical air swing button to adjust vertical air flow direction 7 Press the Horizontal air swing J button to adjust vertical air flow direction 20 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 20 2015 01 05 5 11106 Cleaning and maintaining the air conditioner A Make sure to turn off the circuit breaker when cleaning the air conditioner CAUTION l Cleaning the exterior 1 Wipe the surface of the unit with a slightly wet or dry cloth when needed HSII N3 Do not use Benzene Thinner or Clorox They may damage the surface of the air conditioner and can AUTON create a risk of fire l Cleaning the filter Air filter Washable air filter captures large particles from the air The filter can be cleaned with a vacuum or by hand washing
29. e or button to move the air flow direction up and down or left and right while the air conditioner is turned on gt When the blade reaches the desired position press the or button one more time to set the air flow direction The up down and left right tilting of the blade will stop rc Temi G Remote controller display 16 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 16 2015 01 05 5 11102 Setting the On Off timer You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is on When the air conditioner is off 1 Press the Timer button to select On On indicator starts to blink and you can set the time 2 Press the lt or gt button to set the time You can set the time in 0 5 hour unit from 0 5 3 hours and 1 hour unit from 3 24 hours Time can be set from minimum 0 5 hours to maximum 24 hours 3 Press the SET button to complete the On timer setting On indicator and the set time of the timer will be displayed on the remote controller display and the Timer indicator a will be displayed on the indoor unit display On timer setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the On indicator on the remote controller display and the Timer indicator m on the indoor unit display HSII N3
30. erating condition of outdoor temperature is higher than 35 C try to have more space Make sure to clear a passage for a person and air flow Observe the clearances and dimensions as seen below when installing the outdoor unit If you install several outdoor units at the same place observe the space for ventilation and free airflow If the space for ventilation is insufficient the air conditioner may not generate performance designed Keep in mind that SAMSUNG logo is located on the front side of outdoor unit vvv v 34 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 34 2015 01 05 5 11109 Electrical work The electrical work should be performed by a specialist qualified for the work gt Use the three phase power supply and be sure to install the sub power distributing board for exclusive use with the unit separately purchased by the user Avoid multiple connecting wiring as it can cause a drop in voltage thus resulting in poor performance of the automatic control circuit gt Be sure to install circuit breaker separately purchased by the user gt Be sure to connect the grounding wire HSII N3 Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible NOTE VU l le l Wiring standard cord Code designation IEC 60245 IEC 66 CENELEC HO7RN F Remove the screw on the electrical component box and remove the cover plate Route the connection co
31. erence of the current and desired temperature Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room gt Ifyou are not going to use the air conditioner for a while we recommend to operate the Fan mode for 3 4 hours to dry the internal part of the air conditioner Heat Applicable model AP30M1 gt In Heat mode the indoor temperature fan speed and air flow direction can be adjusted at your desire to warm your indoor gt Indoor unit may not start the operation immediately until indoor heat exchanger is warmed up to a certain temperature approximately 5 minutes according to current indoor temperature to prevent generating a cold breeze gt Defrost display When removing frost at the outdoor unit in the Heat mode Defrost icon will be displayed on the indoor unit display and it will be turned off after removing the frost When removing the frost during the defrost operation in Heat mode steam may be generated and the warm breeze may not come out from the indoor unit B When the outdoor temperature is low and humidity is high frost may form on outdoor unit s heat exchanger and may decrease the heating performance so the Defrost operation will operate for 5 12 minutes to get rid of the frost on the outdoor unit heat exchanger Indoor unit will be off during Defrost operation is on since cold air may come out from it Intervals between Defrost operation cycle may
32. fixed wiring in accordance with the wiring rules l Connecting the power terminal vvvyv Connect the cables to the terminal board using the compressed ring terminal Use rated cables only and make sure to fix them without applying any external force to the terminal Connect the cables with driver and wrench that can apply the rated torque to the screws Make sure that appropriate tightening torque is applied for cable connection If the terminal is loose arc heat may occur and cause fire and if the terminal is connected too firmly terminal may get damaged HSII N3 Screw Tightening torque kgf cm M3 5 0 7 5 M3 5 8 0 12 0 M4 12 0 18 0 M5 20 0 30 0 M6 25 0 37 5 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 37 37 2015 01 05 5 11110 Installation method l Outdoor unit When using the anchor bolt Fix the unit on a flat rigid floor using the anchor bolt Anchor bolt M10 x 4 points separately purchased Anchor bolt fixing dimensions 660mm When using the rubber leg Put the rubber leg to the outdoor unit leg Outdoor unit leg Rubber leg l Installation procedures 1 The piping of this unit can be connected to the right left and rear side When you hit the area for piping connection slightly with a hammer a hole is made Holes for piping connection 4 points Drain hose When the hole on the wall is lower than the When the hole
33. he air conditioner regularly by a qualified service technician Do not open doors and windows in the room being cooled during operation unless necessary Do not block the air conditioner vents If objects block the air flow it may cause unit malfunction or poor performance The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Ensure the off on and protection switches are properly installed Do not use the air conditioner if damaged If problems occur immediately stop operation and disconnect the plug from the power supply If the air conditioner will not be used for an extended period of time for example over several months unplug the power from the wall Call the place of purchase or a contact center if repairs are needed gt Potential risk of fire or electric shock if disassembly or repairs are attempted by a non qualified service technician Mirage_AP30M0 _IBIM_EN_05320A 00 indd 8 2015 01 05 2 5 10159 Viewing your air conditioner Congratulations on the purchase of the air conditioner We hope you enjoy the features of your air conditioner and stay cool with optimal efficiency Please read the manual to get started and to make the best use of the air conditioner l Checking the indoor unit and display Carefully unpack your air conditioner and check the indoor unit to make sure it is not damaged HSII
34. her domestic appliance connected to the same electric lines Use a rated circuit breaker only gt Never use steel wires or copper wires as a circuit breaker It may cause fire or unit malfunctions Do not put undue stress or place heavy object on the power cable Do not bend the power cable excessively gt Potential risk of fire or electric shock To protect the product from water and possible shock you should keep the power cable and the connection cord of the indoor and outdoor units in the protection tube Disconnect the air conditioner from power supply before it is repaired or disassembled Clean the air conditioner after the inner fan stops operating gt Potential risk of injury or electric shock Use a receptacle that has a ground terminal The receptacle must be used exclusively for the air conditioner gt Improper electrical grounding may cause electric shock or fire Be sure to ground the unit Do not connect the ground wire to gas or water pipes lighting rods or telephone grounding lines gt Ifthe unit is not properly grounded electric shock may result If you smell burning plastic hear strange sounds or see smoke coming from the unit unplug the air conditioner immediately and call a contact center gt Potential risk of fire or electric shock A CAUTION SIGNS CAUTION N Do not block or place items in front of the air conditioner Do not step hang onto or place heavy items on the air con
35. igerant used in the air conditioner must be treated as chemical waste Dispose the refrigerant following national standards Have a qualified service technician install the air conditioner and perform a trial operation Firmly connect the drain hose to the air conditioner for proper water drainage Check for damages on the outdoor unit installation pad at least once a year gt Potential risk of personal injury or property loss Mirage_AP30M0 _IBIM_EN_05320A 00 indd 7 2015 01 05 5 10159 Safety precautions A CAUTION SIGNS CAUTION w When using a wireless remote controller the distance should not be more than 7 meters from the air conditioner If the remote controller is not used for a long period of time remove the batteries to prevent leakage of electrolyte When cleaning the outdoor unit touch the heat exchanger radiator fins with extreme care gt Wearing thick gloves can protect your hands Make sure that the condensed water dripping from the drain hose runs out properly and safely The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Young children should be supervised to ensure that they do not play with the appliance Inspect the condition electric connections pipes and external case of t
36. ion operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to against cold air when the heat pump is heating Defrost cycle The internal fan will be off to against cold air when the heat pump is heating The air conditioner does not start operating immediately to protect the compressor of the outdoor unit after it has been started HSII N3 Protect compressor B If the heat pump is operating in Heat mode defrost cycle is actuated to remove frost from an outdoor unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the defrost cycle is completed NOTE 23 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 23 2015 01 05 2 5 11107 Appendix Troubleshooting Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does not operate immediately after it has been restarted Because of the protective mechanism the appliance does not start operating immediately to keep the unit from overloading The air conditioner will start in 3 minutes The air conditioner does not work at all Check if the circuit breaker is switched off Check if there is a power failure Check your fuse Make sure it is not blown out The temperature does not change Check if you selected Fa
37. itioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual gt Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners Make sure that you earth the cables caution DO not connect the earth wire to the gas pipe water pipe lighting rod or telephone wire If earthing is not complete electric shock or fire may occur Install the circuit breaker If the circuit breaker is not installed electric shock or fire may occur Make sure that the condensed water dripping from the drain hose runs out properly and safely Install the power cable and communication cable of the indoor and outdoor unit at least 1m away from the electric appliance Install the indoor unit away from lighting apparatus using the ballast Ifyou use the wireless remote controller reception error may occur due to the ballast of the lighting apparatus Do not install the air conditioner in following places Place where there is mineral oil or arsenic acid Resin parts flame and the accessories may drop or water may leak The capacity of the heat exchanger may reduce or the air conditioner may be out of order The place where corrosive gas s
38. lder 1 1 16 M4XL25 screws 6 6 29 2015 01 05 5 11108 Accessory parts list Indoor unit Quantity No ltem Description Remarks AP30M1 AP30M0 S 1 SS Fixing bracket for indoor unit 2 2 ES 2 Remote controller 1 1 3 U Remote controller holder 1 1 4 M4 X L12 screws 4 4 3 M4 X L14 screws 4 4 Indoor unit 6 Batteries for remote controller 2 2 7 Protective piping cover 1 1 8 Insulation for piping 1 1 9 User and Installation manual 1 1 30 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 30 2015 01 05 5 11108 Selection of installation place l Indoor unit gt Install the unit at a place close to the wall facing the outside as it is necessary to perform piping connection with the outdoor unit Itis effective to install the unit at a window side to ensure uniform distribution of indoor temperature gt Install the unit at a place where there is no obstacle against the wind around the air intake and air outlet gt Install the unit horizontally at a stable rigid place When installing the unit at a place subjected to oscillation noise may occur HSII N3 gt Avoid a place near the door which is frequented by people gt Avoid a place subject to direct sunlight Top view Z MM More than _ 60cm 2 aa Corner installation Wall installation Side view More than 50cm Air outlet Air intake More than
39. mains in the refrigeration pipes it will affect the compressor reduce to cooling capacity and could lead to a malfunction 1 Connect each assembly pipe to the appropriate valve on the outdoor unit and tighten the flare nut 2 Connect the charging hose of low pressure side of manifold gauge to the packed valve having a service port as shown at the figure 3 Open the valve of the low pressure side of manifold gauge counter clockwise 4 Purge the air from the system using vacuum pump for about 10 minutes Close the valve of the low pressure side of manifold gauge clockwise Turn off the vacuum pump Make sure that pressure gauge show 0 1MPa 76cmHg after about 10 minutes This procedure is very important in order to avoid gas leak Remove the hose of the low pressure side of manifold gauge 5 Set valve cork of both liquid side and gas side of packed valve to the open position 6 Mount the cap and the needle valve cap to the valve see the below illustration and tighten them at the torque of 183kgf cm with a torque wrench 7 Check for gas leakage At this time especially check for gas leakage from the 3 way valve s stem nuts and from the service port cap Gas pipe side OUTDOOR UNIT Liquid pipe Indoor unit side D C Liquid pipe side Gas pipe side Vacuum Pump 3 way valve 3 way valve B A Outdoor unit Needle valve cap a Mir
40. n mode Press the Mode button on the remote controller to select another mode The cool warm air does not come out of the air conditioner Check if the set temperature is higher lower than the current temperature Press the Temp or button on the remote controller to change the set temperature Press the Temp or button to increase or decrease the temperature Check if the air filter is blocked by dirt Clean the Air filter every two weeks If the air conditioner has just been turned on or the indoor temperature reaches the desired temperature only fan will operate around 3 minutes for the product protection Also just after you start the heating operation warm air will come out after for a while to avoid cold air from coming out The fan speed does not change Check if you selected Auto or Dry mode The air conditioner automatically adjusts the fan speed to Auto in Auto Dry mode Timer function does not set Check if you press the Set button on the remote controller after you have set the time Odors permeate in the room during operation Check if the appliance is running in a smoky area or if there is a smell entering from outside Operate the air conditioner in Fan mode or open the windows to air out the room The air conditioner makes a bubbling sound A bubbling sound may be heard when the refrigerant is circulating through the compressor Let the air conditioner operate in a selected mode
41. ng thuy gHaggaAEa106s000303604454 4wawbs2wEuaa gtebilissptstusiftdagli A4 IAE U s a s30 ca 122263 t n g n b n 1 83003104456664 se ti S d E EE 25x06 kianlsiiasa xa lnstallation Method s ssxx xxx5 64666 ta E AI PUIGEY 93a 654 1424512 0 82 iin skis AERE EET IEAA A AAEE 48 t C8 naensaciis ladon n6 12 xaxixa Xe Refrigerant charging s x3x4255444 lt ekasascaaada dagtbliiib Sen SuDig RERE REESEN S 855406055 Y23ex xpsaaSs a E ga co a h Gheck and testoperationy serieren EEEE EEE EE AO ARE aaaccamensraesiaiasennanndenadad santas Packing and unpacking guide How to connect your extended power cables Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should c
42. ntact center to install the air conditioner gt Improper installation carries a risk of unit malfunction water leakage electric shock or fire gt lfinstalling in specialty areas such as a factory complex or saline coastal area consult the place of purchase or contact center for specific installation details gt The units must be installed according to distances declared in order to permit accessibility from each side either to guarantee correct operation of maintenance or repairing products The unit s parts must be reachable and removable completely under safety condition for people or things Consult a dealer regarding the appropriate measures to prevent the allowable concentration from being exceeded gt Ifthe refrigerant leaks and cause the concentration limit to be exceeded hazards due to lack of oxygen in the room may result If the indoor unit gets wet turn the power off immediately and call your nearest contact center gt Potential risk of fire or electric shock Mirage_AP30M0 _IBIM_EN_05320A 00 indd 5 2015 01 05 5 10158 Safety precautions A SEVERE WARNING SIGNS WARNING w Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any ot
43. om the set Take out the cushion top Take out the cushion mid Move the set from the cushion bottom 00 R9 48 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 48 2015 01 05 5 11116 Outdoor unit Cushion top HSII N3 Packing case Outdoor unit 2 A Cushion bottom gt Packing the unit as below procedure 1 Put the outdoor unit onto the cushion bottom 2 Put the cushion top onto the outdoor unit 2 3 Put the packing case from the top of set 4 Seal the packing case 2 gt Unpacking the unit as below procedure Take out the packing case from the set 1 2 Take out the cushion top 3 Move the set from the cushion bottom 49 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 49 2015 01 05 2S 5 11417 How to connect your extended power cables Items to prepare compressor and insulation tape should be prepared by an installation technician Tools Crimping plier Connection sleeve mm Insulation tape Contraction tube mm Spec MH 14 20 x 67 0 H x OD Width 18mm 50x 8 0 LxOD Shope SSD 2 TH 1 As shown in the figure peel off the shields from the rubber wire of the power cable Peel off 20 mm of the wire shields of the tube installed already A After peeling off the tube wire you must insert a contraction tube CAUTION 2 Insert both sides of core wire of the power cable into the connection sleeve 3 Using a comp
44. on the wall is higher than the hole hole for piping connection for piping connection 2 Open the front panel and separate it from the unit Be careful of the power lines connected to control panel when removing 3 Bend the connection pipe to an appropriate length using the spring bender depending upon the installation place Allowable pipe length Maximum 15m Allowable pipe drop distance Maximum 10m Make no more than ten bending points on the pipe During initial installation fill the additional refrigerant if the pipe length exceeds 5 m 38 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 38 2015 01 05 2 5 11111 For every 1 m of exceeding pipe length fill additional refrigerant as stated below Model Additional refrigerant amount AP30M0A 30 g m AP30M1A 40 g m Ex If total piping length is 30m and additional refrigerant amount is 40 g m 2 300 g standard filling amount for 5 m pipe Factory fault 1 000 g 40 g m x 30 m 5 m Additional refrigerant amount Fill during the installation 3 300 g Total amount of refrigerant filling Make sure to open the service valve before taking the trial operation A If the pipe is lengthened the performance of the unit is degraded and the service life is shortened Therefore the pipe length should be as short as possible less than 15 m HSII N3 CAUTION Indoor unit Indoor unit Outdoor Fix the pipe N Less than 10m Outdoor Less
45. ontact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Mirage_AP30M0 _IBIM_EN_05320A 00 indd 3 2015 01 05 5 10158 Safety precautions Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions A WARNING Hazards or unsafe practices that may result in severe personal injury or death A CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage A CAUTION To reduce the risk of fire explosion electric shock or personal injury when using your air conditioner follow these basic safety instructions Do NOT attempt Do NOT disassemble Do NOT touch Follow directions carefully Unplug the power plug from the wall socket Make sure the machine is grounded to prevent electric shock Call the contact center for help DSENA These warning signs are here
46. plosion and injury Mirage_AP30M0 _IBIM_EN_05320A 00 indd 41 41 2015 01 05 2 5 11118 Installation method Pipe bending 1 Perform bending of the pipe using the bender which has a specified bending radius 2 Be sure to take full care to perform bending of the pipe successfully at one time Bending and unbending the pipe more than twice makes the bending work increasingly difficult 3 You may use the spring inserted into the gas pipe instead of the bender to jer bend the pipe 4 When you bend the pipe using the spring hold the pipe with both hands to prevent any distortion and secure a minimum bending radius of more than 100mm Spring Tightening of connection parts gt Align the pipes to be connected and tighten the flare nuts first manually and then with a torque wrench applying the following torque v v Outer diameter mm Tightening torque kgf cm 66 35 140 170 15 88 440 480 gt You can avoid of gas leakage by applying refrigerant oil on the flare connection part Drilling a hole in the wall gt Drilla hole ata slightly downward slant 15 with a diameter of 60 65 mm gt The drilling should be done at a distance of less than 150 mm from the floor facing the indoor unit lfa hole on the wall is above 150 mm from the floor use a hole for drain hose 35 mm for connecting drain hose Less than Hole for drain hose 42 Mirage_
47. rd through the side of the indoor unit and connect the cable to terminals Route the other end of the cable to the outdoor unit through the ceiling amp the hole on the wall Reassemble the electrical component box cover carefully tightening the screw outdoor units Model AP30M0 Series AP30M1 Series Power 1 phase 220V 240V 50Hz Circuit breaker Earth leakage circuit breaker ELCB 30A Below 20m 2 5mm Electric wire Below 50m 4mm Allowable voltage 198V 242V Min size of electric wires from to the indoor 0 75 mm You must compress the solderless ring to the cable and then connect it to the main power terminal caution 50lderless ring selection one F E Silver solder Ec Thickness of cable mm B mm d2 mm 25 Less than 9 5 More than 4 5 4 Less than 9 5 More than 4 5 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 35 35 2015 01 05 5 11109 Electrical work l Indoor and outdoor connection wiring gt When connecting the wiring harness between the indoor and outdoor unit align the outdoor side and the indoor side with the terminal board No When the wiring harnesses of the indoor and outdoor unit are not properly connected it may cause trouble Be careful not to allow the indoor and outdoor wirings and power lines to get in contact with the service valve of the refrigerant system or to the pipe without an insula
48. ressor compress the two points and flip it over and compress another two points in the same location The compression dimension should be 8 0 After compressing it pull both sides of the wire to make sure it is firmly pressed 4 Wrap it with the insulation tape twice and position your contraction tube in the middle of the insulation tape 5 Apply heat to the contraction tube to contract it 6 After tube contraction work is completed wrap it with the insulation tape to finish 50 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 50 Unit mm Power cable provided a 120 180 Wire tube power cable Compress it 4 times Insulation tape Te 40mm tube Insulation tape In case of extending the electric wire please DO NOT use a round shaped pressing socket warning Icomplete wire connections can cause electric shock or a fire 2 2015 01 05 5 11117 Memo HSII N3 51 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 51 2015 01 05 2 5 11417
49. rity function is not supported by this model NOTE 10 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 10 2015 01 05 5 10159 Checking the remote controller l Remote controller buttons You can activate the air conditioner by pointing the remote controller away from it When using the remote controller always point it directly at the air conditioner HSII N3 Vertical air swing Adjusts the air flow direction up and down Not applicable to Duct type models Power Turns the air conditioner on or off Mode Selects operation mode Temperature Adjusts the temperature Fan speed Adjusts the fan speed Options Selects options during operation Horizontal air swing Adjusts the air flow direction left and right Timer Turbo Sets timer option Sets the Turbo function SET i i Selects or cancels an option Direction P Moves to select and set an option When you press the button a short ring will sound and a transmit indicator appears on the remote controller display Remote controller will remember the most recent temperature setting if you turn off the air conditioner and then turn it on again NOTE 11 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 11 2015 01 05 5 11100 Checking the remote controller l Remote controller display Operation mode Remote controller Heat mode is applicable to puto Eo DrylS ee transmission AP30M1 model only Fa n He at val Low batien
50. s sold or transferred gt This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non compliant units gt The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and hydraulic lines Failure to comply with these instructions or to comply with the requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty gt The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry gt Donotuse the units if damaged If problems occur switch the unit off and disconnect it from the power supply gt In order to prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNGS technical support if the unit produces smoke if the power cable is hot or damaged or if the unit is very noisy gt Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only gt The unit contains moving parts which should always be kept out of the re
51. se foamed polyethylene or EPDM foam with thickness over 7 mm as an pe insulator Drain hose gt Ifthe pipe is installed in a place with humidity over 80 such as within a pit of a building basement sea shore near hot spring or lake etc use an insulator with a thickness over 10 mm gt Insulate the high pressure liquid pipe low pressure gas pipe pipe and finish it by winding up the vinyl tape around it gt Make sure to insulate the pipe with no gap or cracks and use adhesive between the connection part of the insulator to prevent moisture from entering gt Make sure that the thickness of the insulator doesn t get thinner on the bending part of the pipes Use extra insulator to secure thickness when the insulator becomes thinner gt When the pipe hanger is installed wind the extra PE Foam type insulator over 5 mm with the width 3 times wider than the hanger Do not use cable tie as an hanger v Oil trap Check the following list and install an oil trap gt Install an oil trap only when the outdoor unit is at a higher level than the indoor unit gt Based on cooling operation install it on the gas side pipe only gt Install the oil trap only in between the outdoor unit and the first branch joint and it should be installed at every 10 m gt Radius of curvature R on the oil trap are as follows Unit mm Pipe diameter D Radius of curvatur
52. tion AP30M0X Series Indoor unit Outdoor Unit f _ Panel board Indoor and outdoor connection wire Power cable Purchase separately AP30M1 Series Connnector Connnector Control box Indoor unit Outdoor Unit uji Panel board Indoor and outdoor connection wire Power cable Purchase separately 36 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 36 2015 01 05 2 5 11110 l Electrical wiring gt Connect it to the terminal board N and L for power cable to the outdoor unit In so doing peel off the end of the power cord by about 5mm and press the cord to the ring terminal for hooking Make sure to install exclusive power supply If you use multiple connecting there is a risk of electric shock or fire Ifthe outdoor power supply has been selected install circuit breaker ELCB Purchase separately Make sure to connect earth wire Make sure that the clamping force of the screw on the terminal is tightened firmly within the range of rated tightening torque The appliance shall be installed in accordance with national wiring regulations for installation SASO 2007 2002 Disconnection means must be incorporated in the
53. tion Every 2weeks Every 3 months Every 4months Once a year Clean the air filter 1 Clean the condensate drain pan 2 e Thoroughly clean the heat exchanger Indoor unit 2 Clean the condensate drain pipe 2 e Replace the remote controller batteries 1 Clean the heat exchanger on the outside of the unit 2 Clean the heat exchanger on the inside of the unit 2 Clean the electric components with jets of air 2 Outdoor unit Verify that all the electric components are firmly tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 J This check mark requires checking the indoor outdoor unit periodically following to the description to maintain the air conditioner properly The checks and maintenance operations described are essential to guarantee the efficiency of the air conditioner The frequency of these operations varies according to the characteristics of the area the amount of dust etc NOTE 1 The described operations should be performed more frequently if the area of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the Installation part 22 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 22 2015 01 05 5 11106 Internal protections via the unit control system This internal protect
54. tion triggers and the air conditioner will stop Condensation may occur on the indoor DRYING 18 C to 32 C 21 C to 52 C unit with risk to have either water blow off or drops on the floor B The standardized temperature for heating is 7 C If the outdoor temperature drops to 5 C or below the heating NOTE capacity can be reduced depending on the temperature condition If the cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity Mirage_AP30M0 _IBIM_EN_05320A 00 indd 25 25 2015 01 05 5 11107 Installation manual Safety precautions Carefully follow the precautions listed as below because they are essential to guarantee the safety of SAMSUNG product Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components WARNING Verify that installation and testing operations are performed by qualified personnel Verify that the air conditioner is not installed in an easily accessible area General information gt Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order to be able to use it as reference after installation gt Formaximum safety installers should always carefully read the following warnings gt Store the manual in a safe location and remember to hand it over to the new owner if the air conditioner i
55. to complete the Off timer setting Off indicator and the set time of the timer will be displayed on the remote controller display and the Timer indicator will be displayed on the indoor unit display Off timer setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the Off indicator on sty c the remote controller display and the Timer indicator on the indoor unit display f L 1 Cancel gt Press the Timer button gt Select Off gt Press the lt or gt button gt Set the time to J J gt Press the SET button Combining On Timer and Off Timer When the air conditioner is off When the air conditioner is on When set time on On timer is shorter than Off timer When set time on On timer is longer than Off timer Ex On timer 3 hours Off timer 5 hours Ex On timer 3 hours Off timer 1 hour The air conditioner will turn on after 3 hours from The air conditioner will turn off after 1 hour from the the moment you have set the timer and the air moment you have set the timer and turn on after 2 hours conditioner will remain on for 2 hours and then turn off from the moment it was turned off automatically B Set time for the On timer and the Off timer should be different from each other nore When the On timer or the Off timer is set setting can be cancelled by pressing the Power H button 18 Mirage_AP30M0 _IBIM_EN_05320
56. to prevent injury to you and others Please follow them carefully After reading this section keep it in a safe place for future reference A SEVERE WARNING SIGNS WARNING D Do not place the air conditioner near hazardous substances or equipment that releases free flames to avoid fire explosions or injuries gt Potential risk of fire hazard or explosion Do not install the outdoor unit at an unstable place or elevated surface where there is potential risk of falling gt lfthe outdoor unit falls it may cause personal injury or loss of property Failure or damage may occur if any changes or modification that is not stated in the manual was performed In this case user will be responsible for the repair expenses Install the air conditioner away from direct exposure to sunlight heating apparatus and humid places gt Hang curtains on windows to boost cooling efficiency and to avoid the risk of electric shock Mirage_AP30M0 _IBIM_EN_05320A 00 indd 4 2015 01 05 5 10158 Do not yank the power cable with hands gt Potential risk of fire or electric shock Never use a damaged or dusted power cable or loosened power receptacle gt Potential risk of fire or electric shock Install an exclusive circuit breaker and short circuit breaker for the air conditioner gt Potential risk of electric shock or fire Do not insert anything such as fingers or branches into the air conditioner vents while the air conditioner is running
57. uch as sulfurous acid gas generates from the vent pipe or air outlet The copper pipe or connection pipe may corrode and refrigerant may leak The place where there is a machine that generates electromagnetic waves The air conditioner may not operate normally due to control system The place where there is a danger of existing combustible gas carbon fiber or flammable dust The place where thinner or gasoline is handled Gas may leak and it may cause fire 27 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 27 2015 01 05 5 11107 Accessory parts list Product illustration may look different from the actual product l Piping Box Connection parts Quantity No Item Description Remarks AP30M1 AP30M0 1 Drain hose 1 1 2 Connection pipe amp insulation 1 1 6 35mm 1 4 3 Connection pipe amp insulation 1 1 6 35mm 5 8 4 Connection wire 4 strand 1 1 Piping box 5 Connection wire 2 strand 1 6 Connection wire 2 strand 1 T Ta Drain plug out 2 C 8 p Finishing tape 2 2 28 Mirage_AP30M0 _IBIM_EN_05320A 00 indd 28 2015 01 05 5 11107 Others Mirage_AP30M0 _IBIM_EN_05320A 00 indd 29 Quantity No Item Description Remarks AP30M1 AP30M0 Z O N Ge 10 S Rubber leg 4 4 11 A Cabletie 8 8 12 6D Bushing pipe 1 1 Piping box 13 Vinyl tape W19X5m 1 1 14 Cabi hole rubber 1 1 15 Pipe ho

Download Pdf Manuals

Related Search

Related Contents

Trust Silicone Skin for iPad 2  Smartline UV/VIS Detector 2550 user manual      Da-Lite No.6 Wall Brackets, 6" Ext.  Broan-NuTone Nutone QT90 QuieTTest 90 CFM Ceiling Mounted Ventilation Fan  取扱説明書 - M  USER INSTRUCTIONS - Flowserve Corporation  # 21 4275 Bauanleitung 2 9 Building instructions 10    

Copyright © All rights reserved. Failed to retrieve file