Samsung SU4341 User Manual (XP)
Contents
1. The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B Reposition bottom plate and 4 screws Tighten screws securely Maintenance joe 0 3 8 How to replace Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Remove the 5 screws as shown with a screw driver EN Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide E When to replace the agitator brush roll When agitator brushes are worn the agitator should be replaced To check condition of brushes disconnect cleaner from electrical outlet Move the edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushe2. 50 4340 SERIES Before operating this unit please read the instructions carefully For indoor use only English imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service please register your product at www samsung com register Contents IMPORTANT SAFETY INSTRUCTIONS rsssressssssesseeseesseeseeseeeseeeeesscsseenecessessesseeseesseesseneeegs 3 IDENTIFIGATIONS OF PARTS iiisectisacedstsseiess che ssectecisatsnacd secesnesceddieeseasea igessstsbecdniensoascazes sans 4 ATTACHING THE HANDLE 4 ATTACHING THE HOSE AND TOOLS ssrsssesstsssessessteseesseeeeesececeseeeecesesesssseessecseseseesaeeneenaes 5 OPERATION 5 MAINTENANCE 8 TROUBLESHOOTING 11 IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not leave vacuum cleaner unattended when it is plugged in Unplug from outlet when not in use and befo
3. Filter Cup located at the bottom of the Dirt Cup and twist counterclockwise to unlock and remove Cleaning the Pre Post motor Filter How to clean Disconnect cleaner from electrical outlet The Pre Motor Filter protects the Motor from debris It is located underneath the Dirt Cup and Filter Cup in the Center of the round part of the Cyclone Lever Remove the small round Filter and any debris on top of it Rinse well under warm water then air dry thoroughly before replacing The Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the front of the Cleaner When the filter becomes dirty The Hepa Filter Open the door remove the filter and replace The Hepa Filter is not washable and must be replaced Replace the door by inserting the tabs on the left side and snapping the right side into place Grasp the Circular Filters and twist to unlock Pull straight up to remove Separate the Outer foam and Inner pleated Circular Filters Wash each individually by hand in warm water Mild detergent may be used if desired Rinse well then air dry Thoroughly dry before putting them back together and replacing in the Filter Cup The Filter Cup may be washed In warm water with a mild detergent Make sure it is completely dry before reassembling with fliters Do not operate cleaner without Either the Pre Motor Filter or Post Motor Filter in place
4. eaner They may damage the cleaner Always turn off this appliance before connecting or disconnecting the hose removing the bottom plate for maintenance Use only on dry indoor surfaces never change the plug in any way Do not modify the polarized plug to fit a non polarized outlet or extension cord Do not touch the brush roller when it is rotating Keep suction away from your face when using nozzles and pipe Do not pull the power cord around sharp corners and do not allow it to be trapped Unplug before connecting turbine nozzle only using turbine brush model e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance The plug must be removed from the socket outlet before cleaning or maintaining the appliance the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only FOR RESIDENTS OF THE UNITED KINGDOM ONLY If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved t
5. hort nozzle hose and the bottom plate Mini Turbo Brush Use for upholstered furniture carpeted stairs and hard to reach places Brush bar Replacement Remove bottom plate With the curved ends facing Remove the tool from the hose And remove brushbar and down slide end plates of and turn upside down Slide the discard brushbar into slots on the tool switch to unlock position Inspect belt to ensure that it is To replace bottom plate insert in good condition If broken or the four tabs on edge of cracked please replace bottom plate into slots on front See below for details of tool Pivot bottom plate down and snap closed Belt Replacement Cleaning Brushbar Grasp turbine and pull firmly to retainers pointing down slide Cut off pet hairs or threads remove retainers into grooves in tool surrounding brush by using Remove belt from turbine pulley housing and snap into place scissors Replace with new belt Replace brushbar and bottom plate 10 Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center Problem Cleaner won t run Problem Poor job of dirt pickup Possible Cause Possible Cause Possible Solution Possible Solution Not firmly plugged in Full or clogged Dirt Cup Plug unit in firmly Empty the Dirt Cup and check for blockages No voltage in wall plug Broken or worn belt Check fuse or breaker Replace belt Blow
6. l attachments Attachment tools can be used to clean furniture or drapes on stairs or in corners When using the attachments ensure the vacuum cleaner is placed firmly on the floor with the handle in the upright position Do not place the vacuum on top of furniture or steps as the brushroller may cause damage option E Wooden Floor Brush Select Models Use for bare floors Swivel head turns to get into tight spaces and fits under cabinets Note The Wooden Floor Brush does not store on board Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner and will prevent rug from clinging to cleaner Continue to lift front of cleaner so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower front of cleaner and use only forward strokes Height adjustment 1 Place handle in upright position 2 Turn height adjustment dial A to desired setting Bare Floor For no carpeted bare floors Low Setting For short pile carpets Medium Setting For short and medium pile carpets Highest Setting For plush pile carpet Note For optimal cleaning performance adjust to the lowest practical setting If your cleaner is difficult to push adjust to the next higher setting Always ensure that the correct height setting is used for your f
7. looring type as damage may occur if the height setting is not changed to reflect your flooring type 6 Operation A When using the hose attachment please ensure that vacuum remains flat and level on the floor surface to prevent contact from the brush roller with the floor surface If the vacuum does not remain flat and level this could result in damage to the flooring CAUTION A To reduce risk of injury and potential damage to floor surface do not use the caution Vacuum on a staircase Always use vacuum from the bottom of the staircase and ensure that the vacuum remains securely flat on the floor surface Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness When to empty the Dirt Cup The dirt cup needs to be emptied when the dirt reaches the MAX line on the side of the Cup If more dirt than this accumulates your cleaner will not operate effectively Note All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming Emptying the Dirt Cup Disconnect cleaner from electrical outlet 3 1 ln Slide the Cyclone Lever to the Unlock position Grasp handle and pull the Dirt Cup straight out to remove from Vacuum Empty dirt into garbage container Put the Dirt Cup back in the vacuum and slide the lever to the Lock position Cleaning The Circular Filters Grasp the
8. n fuse or tripped breaker Clogged hose or nozzle Replace fuse or reset breaker Clean hose or nozzle area Filters blocked or dirty Hole in hose Clean filters as per manual instructions Replace hose Dirt Cup improperly installed Problem Dust escapes the Dirt Cup Properly install the Dirt Cup _ Incorrect carpet height setting Possible Cause Rotate nozzle control knob to lower setting Possible Solution Clogs in air flow passage Dirt Cup improperly installed Clear clogs clean filters as per manual instructions Re install the Dirt Cup Problem Abnormal sound Problem Cleaner hard to push Possible Cause Possible Cause Possible Solution Possible Solution Strange sound like rushing air Incorrect carpet height setting Check for clogs in hose nozzle area and Rotate nozzle control knob to lower setting filters clear or claen any clogs or blockages as per manual instructions This Vacuum cleaner is approved the following Electromagnetic Compatibility Directive 2004 108 EEC Low Voltage Directive 2006 95 EC If you have any comments or questions regarding a Samsung products contact the SAMSUNG customer care center Country Customer Care Center 2 Web Site U K 0330 SAMSUNG 726 7864 www samsung com SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com 11 DJ68 00294R REV 0 0
9. o BS 1362 fuse is fitted in the carrier contained in the plug If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a 13 amp socket 3 Assembling Parts Identifications of parts The assembled cleaner will look like the illustration to the left WARNING Handle Power switch Quick release cord hook Post Motor Filter Crevice tool Handle release Carrying handle Hose Extension wand Combination tool Cyclone Lever Dirt Cup Filter Cup Upper Tank Cap Cyclone Hose Wand Base Height Adjustment Dial Hose Clip Mini Turbo Brush OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE Step 1 Attaching the Handle Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body Insert the screw provided into the existing hole Tighten the screw securely with a screwdriver Before securing the handle please check that the handle is fitted to the vacuum body and make sure there s no gap Assembling Parts Step 2 Attaching the Hose and Tools Slide the end of the hose wand with tabs into the Hose Wand Base Line up the tabs on the base of the Twist Snap Hose with the corresponding notches on the hose collar as shown Slide the extension wand and the crevice tool together into the storage clip Brush by
10. putting the rib at the bottom of Mini Turbo Brush on two hooks of Handle Snap Mini Turbo Brush into place as shown Operation ON OFF Switch 1 To turn cleaner on press the Power switch 2 To the cleaner off press the Power switch again Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating for general operation on carpet and floors low for reaching under low furniture Step on handle release pedal to lower handle Transporting cleaner To move your cleaner from room to room put the handle in upright position tilt the cleaner back on its rear wheels and push forward Carrying handle The cleaner can also be moved by using the carrying handle 2 f SAP Operation A Combination tool Two types of cleaning tools are included in one attachment rotate for desired tool Use brush side to dust furniture blinds books lamps shelves Use upholstery side for curtains draperies cushions fabrics B Crevice tool Use in corners on stairs baseboards and behind furniture C Extension Wand Use with desired attachments and narrow wand for a longer reach D Mini Turbo Brush Use rotating brush action for small areas such as stairs and upholstery Note Press gently when using Mini Turbo Brush to gain maximum cleaning Too much pressure could cause the brush to stop rotating Cleaning Too
11. re servicing Do not use outdoors or on wet surfaces Use only as described in this manual Use only manufacturer s recommended attachments If vacuum cleaner is not working as it should or has been dropped damaged left outdoors or dropped into water return it to a service center Do not pull or carry by cord use cord a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surfaces Do not unplug by pulling on the cord To unplug grasp the plug not the cord Do not handle vacuum cleaner or plug with wet hands Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches hot ashes Do not use without dirt cup or filters in place Empty dirt cup and clean filter frequently when picking up very fine materials such as powder Turn off all controls before unplugging vacuum cleaner Use extra care when cleaning on stairs Do not use to pick up flammable or combustible materials such as gasoline or fine wood fine wood sandings or use in areas where they may be present Store your vacuum cleaner indoors in a cool and dry area Avoid picking up hard sharp objects with the cl
12. s do not touch card Remove agitator and used belt Discard used belt Grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Maintenance Clearing Blockages Disconnect cleaner from electrical outlet The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can sometimes become clogged If you notice a change in the sound of the vacuum motor check for blockages Check Upper Tank and Grille Remove the Hose and disconnect If the blockage persists turn the Cyclone To open the Cap grasp the Wand vacuum cleaner off and unplug it the holder and turn Toward the Check for clogs in the vacuum Remove the bottom plate Lift up left If the Grille was blocked base the wand the hose and the the short hose in the base of the check and clear the grille in the suction inlet vacuum Inspect the hose for center of the Cyclone clogs and remove any obstructions Replace the s
Download Pdf Manuals
Related Search