H.264 series DVR User's installation and operation Manual Edition
Contents
1. connect the data wire connect the power wire cover the machine fix the cover 2 3 Installation connections sketch map Below just as the 4CH DVR for example Specifically please refer to practical product ALARM IN VIDEO OUT E VIDEO IN Page 7 2 4 Audio and video input and output connections 2 4 1 Video input connections The video input port is BNC connector plug The demand of input signal is PAL NTSC BNC 1 0Vp p 750 The video signal must be accorded with the state standard which has the high signal to noise ratio low aberration and low interference The image must be clear and has natural color in the appropriate brightness Insure the vidicon signal stable and credible The vidicon should be installed in the appropriate location where is away from backlighting and low illumination or adopts the better backlighting and low illumination compensation The ground and power supply of the vidicon and the DVR should be shared and stable Insure the transmission line stable and credible The video transmission line should adopt high quality coaxial pair which is chosen by the transmission distance If the transmission distance is too far it should adopt shielded twisted pair video compensation equipment and transmit by fiber to insure the signal quality The video signal line should be away from the electro magnetic Interference and other equipments sign2. Alarm In Channels Alarm In Chann Enable Type Period Interval Alarm Output Delay Record Channel Tour snapshot PTZ Activation Delay show Message send Email Buzzer FTP upload Copy To Copy Restore Save Cance Picture 4 11 Alarm input Set method refer to chapter 4 3 1 Motion detect 4 3 5 Alarm output Refer to chapter 3 5 4 Page 33 4 3 6 Abnormal Analysing and inspecting current software and hardware of the device When some abnormal events happen the device will make a relative answer such as show message and buzzer Abnormality Event Type No Disk Enable show Message M Buzzer Cancel Picture 4 12 Abnormal Event Type selecting abnormity you want to inspect Enable Select itto make sure abnormal function workable Show message Automatically alarm cue shows on the main screen Buzzer Device will have two long nosie di di while alarm is happening 4 4 System setup Set the system parameters such as General Encode NetWork NetService GUI display PTZ config RS232 and Tour setup Page 34 4 4 1 General General system Time 2012 017 10 Date Format YYYY MM DD Date Separator Time Format 24 HOUR language ENGLISH HDD Full Overwrite Resolution 1024x768 DYR No 0 Yideo Standard PAL Auto Logout 0 Cancel Picture 4 13 General setup System time Set the system data and time Date format Choose the data format YMD MDY DMY Date Separator C
3. CAM 1 Compression Main Stream SubStream Resolution CIF QCIF Frame Rate FPS 25 5 Bit Rate Type Quality Bit Rate A8OM H 1M 6OM H 128K Frame Interval 2 Video Audio Y o Copy To Restore Save Cancel Page 36 Picture 4 16 Encode setup CAM Choose the channel number Compression Standard H 264 main profile Resolution Resolution type D1 HD1 CIF QCIF Frame Rate P 1 frame s 25 frame s N 1 frame s 30 frame s Bit Rate Type You can choose limited code stream or variable code stream When you choose the variable code stream there are six image quality options Bit Rate Set the code stream value to modify the image quality The larger code stream value the better image quality D1 1000 1500kbps CIF 384 1500kbps QCIF 64 512kbps Video Audio When the icons are all selected the video file is video and audio multiplex stream Combine Enable Combine Enable When the icons are all checked opening combination coding functions Mode multi channel playback is used in all channels playback simultaneously and the narrowband transmission is used in multi channel real time remote monitoring simultaneously at narrowband state especially used in mobile monitor 4 4 3 Network setup Network Net Card IP Addr subnet Mask Gateway Primary DNS secondary DNS TCP Port HTTP Port Mobile Port Wire Netcard 192 168 1 EE 192 168 A Ue IT DHCP Enable Net
4. Server Cancel Picture4 17 Network Net Card You can choose cable network card or wireless network card DHCP Enable Obtain IP address automatically not suggested Page 37 Note DHCP server is preinstalled IP address Set the IP address Default 192 168 1 20 Subnet mask Set the subnet mask code Default 255 255 255 0 Gateway Set the default gateway Default 192 168 1 1 DNS setup Domain Name Server It translates the domain name into IP address The IP address is offered by network provider The address must be set and reboot then it works TCP port Default 10000 HTTP port Default 80 Mobile Monitor port Default 34599 Net Service Goto advanced network setup 4 4 4 NetService Choose the network service option and click the set button to configure the parameters PPPoE setup Net Server Net Server PPPOE NTP EMAIL IP FILTER DDNS FTP ARSP Alarmserver UPNP Wireless Net Server Info USER NAME Cime nist gov Stop Stop Stop Stop Enable Stop Stop Stop Stop Stop Picture 4 18 0 0 xqc1974 3322 0rg 192 168 0 135 www edvrddns com AlarmServer 30 ChinaNet Cancel NetService Page 38 PPPOE Enable User Name Password IP Addr Cance Picture4 19 PPPOE Input the user name and password that ISP Internet service provider provides After saving it reboot up your system Then the DVR will build a network connection based on PP
5. The hard disk power supply line is not connected 2 The cables of the hard disk are damaged 3 The hard disk is damaged 4 The SATA port of main board is damaged 4 There are no video outputs in single channel multiple channels and all channels Page 58 Possible reasons are as followed 1 The program is not matched Please update the program 2 The image brightness is all 0 Please restore the default setup 3 There is no video input signal or the signal is too weak 4 The channel protection or the screen protection is set 5 The hardware of the DVR is damaged Real time image problems such as the image color or the brightness distortion Possible reasons are as followed 1 When using the BNC output the option between the N mode or PAL mode is wrong and the image becomes black and white 2 The DVR is not matched the monitor impedance 3 The video transmission distance is too far or the loss of the video transmission line is too large 4 The color and brightness setting of the DVR is wrong can not find the video files in local playback mode Possible reasons are as followed 1 The data line of the hard disk is damaged 2 The hard disk is damaged 3 Update the different program with the origin program files 4 The video files to look up are covered 5 The recording is not on The local video is not clear Possible reasons are as followed 1 The image quality is too bad 2 The reading program is wrong Reboot up the D
6. control purview can modify his her own or other users password Modify Pwd User Name admin Old New Confirm Cancel Picture 4 34 Modify Password Add user Add a user in the team and set the user purview Enter the menu interface and input the user name and password Choose the team and choose whether cover using the user Cover using means that the account can be used by multiple users at the same time Once choose the team the user purview is the subclass of the team We recommend that the common user s purview is lower than the advanced user Page 50 Add User z BLETE User Name Password Confirm Hemo GROUP admin Authority Record Mode M Hetwork MY ideo Blind Y EE Output Y IES MeEncode Config M PT Control MYideo Loss Abnormal ity MM Account MAHDD Management i EJ Hotion Detect Alarm Input fjGeneral Upgrade Save Cancel Picture 4 35 add user Add Group Add a user team and set the purview There are 29 4ch 37 8ch 53 16ch different purviews shut down the equipment real time surveillance playback recording setup video file backup and so on Name Memo Author ty _JRecord Mode _JNetwork ideo Blind JAlarm Output C JDISPLAY JEncode Config JPTZ Control ideo Loss Abnormal ity JAccount Add Group q JHDD Management i JHotion Detect jAlarm Input JGeneral JUpgrade Save Cancel Picture 4 36 Add Group Delet
7. is schedule hint After three seconds the system is shut down Cancel midway is of no effect reboot Quit the system Reboot up the system 3 5 9 Window switch Preview in single window four windows eight windows nine windows sixteen windows according to your choice Page 23 4 Main menu 4 1 Main menu navigation set the recording configuration recording type recording time section Record playback Set recording look up recording play video file storage Detect backup equipment backup the selective files Motion Set motion detect alarm channel sensitivity area linkage parameters detection defending time section alarm output screen hint recording PTZ patrol Video Set camera mask alarm channel sensitivity linkage parameters blind defending time section alarm output screen hint recording PTZ patrol Video Set video loss alarm channel linkage parameters defending time ide loss section alarm output screen hint recording PTZ patrol Alarm Set alarm input channel equipment type linkage parameters defending input time section alarm output screen hint recording PTZ patrol Alarm output Set alarm mode configuration manual shut down Abnormality No disk disk error disk no space and so on General Set system time data format language hard disk full time operation configuration machine number video format output mode summertime stay time Set main assistant coding parameter code mode resolvi
8. recording time formula is Recording time hour overall capability M Capability in an hour M hour channel number The DVR introduces the H 264 compression technology lts dynamic range is very large so the hard disk capability calculation is based on the estimation values of each channel creating files in an hour Example For one piece 1000G HDD real time D1 for recording it will keep recording for about 21 days HDD Spaces per channel is 500M H if 4channels real time D1 at 24hours recording uninterrupted it can last 1000G 500M H 24H 4ch 21 days Page 66
9. the AB lines of the decoder must be less than 5V 4 Front equipment grounding note Bad grounding can lead to the burnout of the chip 5 Alarm input type unlimited The DVR alarm output port is constant opening type alarm input 2 grounding 3 alarm output 4 RS485 a SENSOR Alarm input 1 2 3 4 C1 NO1 Alarm output interface constant open type 485communication interface which is connected with the recording control equipments such as the decoder Page 10 2 5 1 Alarm input port specification 1 channels alarm input Alarm input type unlimited The grounding and the com port of the alarm sensor are parallel The alarm sensor is external power supply The grounding of the alarm and the DVR should be shared The NC port of the alarm sensor must be connected with the DVR alarm input port The grounding of the power supply and the alarm sensor must be shared when used in external power supply 2 5 2 Alarm output port specification 1 channels alarm output There is external power supply when using the external alarm equipment Please refer to the relay relevant parameters to avoid the overload that damages main machine 2 5 3 Alarm output port relay parameters rating 30VDC 2A 125VAC resistance load 125VA 160W sana owe isolation Homo polarity 1000VAC 1minute Inhomo polarity 1000VAC 1 minute Interface and winding 1000VAC 1 minute 1500VAC 10x160us longevity 50x106 MIN 3Hz 200x103 MIN
10. this port eg 60 12 9 26 66 TCP Router will automatically distribute TCP port for the device when monitoring via CMS it need this port Mobile Monitor Port Router will automatically distribute Mobile Port for the device when mobile monitor It need this port ARSP Domain name auto register ARSP Type DNS Enable server IP www edvyrddns com User Name i Cancel Set your user name click Enter to register click Save to save lf successful you will get the domain name username edvrddns com Make sure the network setup is correct before setting up ARSP When the ARSP is successfully configured and start you can input the domain name in the IE address column to visit 4 4 5 GUI Display Configure the video output parameters including the front output mode and code output mode Front output In the local preview mode include channel title time display channel title record status alarm status bitrate info transparency and region cover Code output In the network surveillance and video file mode include channel title time display channel title record status alarm status bitrate info transparency and region cover Page 44 DISPLAY Channel Title Cat Time title HITE channel titlelWHITE M Record Status MAlarm Status Transparency 255 Channe Regional Cover set Time title fgChannel title Set Cancel Picture 4 28 GUI Display Channel Title Click the channel name m
11. 0 5Hz 40 70 Page 11 2 6 Speed dome connections 1 Connect the 485 lines of the speed dome with the DVR 485 interface 3 0 20024 U Ozo S RS485 La SENSOR ALARM R5485 2 Connect the video line with the DVR video input 3 Electrify the speed dome 3 Basic operation Note The button in gray display indicates nonsupport 3 1 Turn on Plug the power supply and turn on the power supply switch Power supply indicator light shining indicates turning on the video recorder After the startup you will hear a beep The default setting of video output is multiple window output mode If the startup time is within the video setting time the timing video recording function will start up automatically Then the video indicator light of corresponding channel is shining and the DVR is working normally Note 1 Make sure that the input voltage corresponds with the switch of the DVR power supply 2 Power supply demands 220V 10 50Hz Suggest using the UPS to protect the power supply under allowable conditions 3 2 Turn off There are two methods to turn off the DVR Entering main menu and choosing turn off in the turn off the system option is called soft switch Pressing the power supply switch is called hard switch Illumination Page 12 1 Auto resume after power failure If the DVR is shut down abnormally it can automatically backup video and resume previous working status after po
12. 7 06 19 00 42 Remove Index CAM File Name Length 1 2 3 4 5 6 F 8 Cancel Picture 4 4 File Backup Query Show the file information satisfying the set file attributes Remove Clear the file information Begin Click the play button to start the backup Cancel During backup you can exit the page layout to carry out other functions 4 3 Alarm Function Alarm functions include motion detect video blind video loss alarm input and alarm output 4 3 1 Motion Detect When system detects the motion signal that reaches the set sensitivity the motion detect alarm is on and the linkage function is turned on Page 29 Motion Detect CAM Enable Sensitivity Region Per 0d Interval Alarm Output Delay Record Channel 3 Tour BAIRE snapshot Talle PTZ Activation Delay Show Message send Email Buzzer FTP upload Copy To Copy Restore Cancel Picture 4 4 Motion Detect CAM Choose the set motion detect channel Enable means that the motion detect function is on Sensitivity Choose in the six options according to the sensitivity Region Click setup and enter the set area The area is divided into PAL22X18 Grey block means the dynamic detect defensive area Black block means the unfenced area You can set the area as followed Drag the mouse and draw the area E MASA AAA Picture 4 5 Region Period Trigger the motion detect signal in the set time section You can set acc
13. A R O EE eT Ren aD 52 ASIN CAUSE 52 AO AO is 53 A A er Creer 53 o Om Sa PE RNC E Dae Me Pare ene 54 AO TWO a PA NAT 54 A acdsee AA cde sos cto cans aeco sme A OR 54 A622 DE A e aon ble eee ea eae 55 A A Cee Tee MCE REE mnR ETE MRO EE meet 55 Onn Col A O O ee ee eee as 56 A SIMUL COWS V SLE M E 57 5 FAG and mantena E veces cesar terns escola a 58 O Saree nee Pane ae CR a iE ste et Bee AE cee ars ON one eer Bee ME eter ee aE eee ear Ue ee ee eT en ce Rae 58 2 NIT US VINO ata A dd 63 Appendix 1 Remote controller A cod 64 ADDeENGIX 2 Mouse operatorie eia edie EE cies E ered 65 Appendix 3 Hard disk capability calculatiON o oooooonooccnoncncnononononanononanocnoncnconnnncnono nono o nono o nncnnnncnnnos 66 Page 3 1 Production Introduction 1 1 Product overview The series DVR is designed specially for security and defence field which is an outstanding digital surveillance product It introduces embedded LINUX operating system which is more stable It introduces standard H 264mp video compressed format and G 711A audio compressed format which insures the high quality image low error coding ratio and single frame playing It introduces TCP IP network technology which achieves the strong network communication ability and telecommunication ability The series DVR can be used individually or online applied as a part of a safety surveillance network With the professional network video surveillance software it achieves th
14. AM 1 PTZ Config Patrol No Preset i Set Goto Focus amp Name preset00i Melete Exit Iris EB Speed 5 Ptz Trace Start stop cruise Picture 3 11 Preset Settings 2 Preset Point Calls In Picture 3 10 write the preset points inthe preset input blank then click button Goto PTZ turn to the corresponding preset point Value input blank PTZ Control 1 CAM 1 Patrol No A Zoom E Preset i Set Goto Focus amp Name preset00i Melete Exit Iris E Speed 5 Ptz Trace Picture 3 12 PTZ Control 2 Cruise between Points Multiple preset points connected cruise lines call cruise between points the PTZ run around on the line 1 Cruise Between Points Settings Cruise lines is connected by multiple preset points setting procedure is as follows Step 1 set your preset points Step 2 click button Patrol No then write proper value into the Preset Points blank and interval blank then click button Ada Step 3 click save complete setting Remove Preset click the preset point item in the information box then click Delete button The preset point will be removed after that Page 21 Patrol No Preset Points Blank Preset 2 Interval 3 Sec Add Delete Index Preset Name Interval 1 1 3 Information of points on the cruise line Cancel Picture 3 13 Cruise Between Points Settings 2 The Calls of Cruise between Points Click right key in preview interface selec
15. Boot Remove Cancel Picture4 45 LOG 4 6 4 Version Display the basic information such as hardware information software edition issue data and so on wi Yersion N ES Record Channel 4 Extra Channel 0 Alarm Input 4 Alarm Output 1 system Y00 00 00 00 16CIF 256M Build Date 2010 02 01 00 00 00 ser ialNo 03 ec 90 89 3f a8 Cance Picture 4 46 Version Page 56 4 7 Shut down system Refer to chapter 3 5 8 Page 57 5 FAQ and maintenance 5 1 FAQ lf the problems are not listed please contact the local service or call the HQ service We are willing to offer the service 1 The DVR can not boot up normally Possible reasons are as followed 1 The power supply is not correct 2 Switch power supply line is not in good connection 3 Switch power supply is damaged 4 The program updating is wrong 5 The hard disk is damaged or the hard disk lines are broken 6 The front panel is damaged 7 The main board of the DVR is damaged 28 The DVR reboots automatically or stops working after boot up a few minutes Possible reasons are as followed 1 The input voltage is not stable or too low 2 The hard disk is damaged or the hard disk lines are broken 3 The power of the switch power supply is low 4 Frontal video signal is not stable 5 Bad heat radiator or too much dust or bad running circumstance for the DVR 6 The hardware of the DVR is damaged 3 System can not detect hard disk Possible reasons are as followed 1
16. CONNECTIONS cee cccsccesscccssseccessseceeseeceeseceesseecesseecesseeceeseeeeesseeeeseeeessees 6 DN MODEM Dae awe CHECK PR anual ioshdualinn iKdari Gd ghcor teu aitdaaliasandue ine eluaasahcen ua adeeGdaNdetiees 6 AOA ARS ANS A A SCOT aT 6 2 3 Installation connections sketch map Below just as the 4CH DVR for example Specifically please refer CO practical produc doi lados 7 2 4 Audio and video input and Output CONNECTIONS ccccccccnnnnnnnnnninonnnnnnnnnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnss 8 2 4 1 Video input connections ut 8 2 42 VIGeO OUIDUUCONNEGHONS ana OPNS arani E naan 8 24 S Audio signan pU e slate tianhateoaasenbaeeoeas 9 LAA AVAGO SION O AAA AI E A 9 ZA input md output Connec HONS aE E aeneRwses Was osiaatinens 9 ZINAA NDUL DONS DCCC AU OM natacion a a a a a a a aa 11 2 5 2 Alarm output port SPECIFICATION saaran a aa aa aa aaa E E 11 2 5 3 Alarm output port relay parameters oooooocconococcconoccncnononnnccnonnnnnonnnnnnnnonnnnccnononncnnonnncnnnnnnccinnnss 11 20 pesa COME COME CIO Sur dr br ddr 12 2 BASIC OSI ELI ON A di 12 Dee AMUN O Die S tae sec etaaet fea edeccatp ost satecanewecees 12 SI AA A O O O A O ON 12 O EMO MU eat E EAL TA EA EA Su E nae A S te Maa cae adie ak E E E A 13 JA PEVE W eane E E A A A a ES 14 3 3 Desktop shorte ut MEA Us 14 CREM AEE T a O AEE E ENE E E IPEN E EE E E PNE aN TN ET O maa E EN 14 A E ee ee E ee eee ee 15 D9 AS CON MOS Aa 18 AN AA A A A A 19 A tr WZ COMMON AA
17. H 264 series DVR User s installation and operation Manual Edition R1 0 Welcome Thank you for purchasing our DVR This manual is designed to be a reference tool for the installation and operation of your system Here you can find information about this series DVR features and functions as well as a detailed menu tree Before installation and operation please read the following safeguards and warnings carefully Important Safeguards and Warnings Do not place heavy objects on the DVR Do not let any solid or liquid fall into or infiltrate the DVR Please brush printed circuit boards connectors fans machine box and so on regularly Before the dust cleaning please switch off the power supply and unplug it Do not disassemble or repair the DVR by yourself Do not replace the components by yourself Environment Please place and use the DVR between 0 and 40 Avoid direct sunlight Stay away from heat source Do not install the DVR in damp environment Do not use the DVR in smoky or dusty environment Avoid collision or strong fall Please insure the DVR level installation in a stable workplace Please install in ventilated place Keep the vent clean Use within the rating input and output scope Page 1 Directory Msigojo Blerilo gl al lpolo AA EE E EEEO 4 Dl PRO GUC OV CIVIC W ri iii id 4 LAA CAS ses sic secon stem scoot Scceanteacenoensueratiemaueatc E E EEA 4 2 Open package check and Cable
18. PP sin deoa a a e 19 00 GOO SCI ii A a 22 So OMPI eee Mn ea ne are eee oe ere ee 23 30 09 LOGOUT add dt di tibias 23 A acest ea dst edhe tect AR A AR A A sea Ue alc hse A clay gece Yea cache ac tbc EE 24 4 Mat ment navita OM cas Sedan carter aes ie res ttn he bl ds 24 Ah Dr ANC COU O 26 42l RECOrd COM ud idad 26 Ae ONP 11 0 Bo d eee nen MCR N 27 A NS A N ET E EET AP aT oee 28 2 Aap 2 41 mee ge ree cee BP Po RE PO A 28 ASA Func HO ast atic waa a et ents wa Gan et eats wa Gane ae eas wa Gane et ea ea Gane et eats eae tena wae et tees wae 29 Bo NIV IO MONE A tet cats eest oe neta copnurees EE EEEN 29 A 3 2 VACO DIN 32 A I VOGO A ncrcaec ns icavae caatepsidc N site aneeand aac oeesaaeu an aa acoanneaacee nase eaeannueaeas 32 ESA nn when ldaesaremdsssanctiessacetdaaheseBioaaed N 33 E o A Dea cess o A 33 1 30 ANO Mi dt 34 SN AMES A A A es ka Dl hence kettle haat A ka Daleatnh S 34 GN E EA A eat mca aes a cst id eae ca A A 35 4A 2 TE e a a E 36 AAS NOTIWOTK SQUID sitiada tada didas 37 PANEI G gt T EMRE y Eon Pe CRO Se UR ee ee ee 38 E A TR 44 AA OF E SOUD so sscai stusscttecpanae N cre stacecacit a aoastauunne auaauaa tanta angen aearntaeentea aur 46 AAT R9232 SOU PD nent Aiea ia Man Ae ee A 47 aAA OOS o W une eR Eee ORR ee eee Te AT Se Re Tn et ek Pee Oa rei hI ae Pree eet Perse or ea nee Ee 47 A ASS dG vad adesienddadieeobadies 48 TRDEM NAO memmec nee crne seer mere ener S 48 45 2 ACCOUN cinan T 49 E In ET I E
19. PoE The IP address will change into dynamic IP address after above operation is well done Operation After PPPoE dialing successfully look up the IP address in the IP address and obtain the current IP address Then use this IP address to visit the DVR through user port NTP setup NTP Enable server IP Port Time one Update Period Picture 4 20 NTP The NTP server must be installed in the PC Server IP Input the IP address installed NTP server Port Default 123 You can set the port according to NTP server Time zone London GMT 0 Berlin GMT 1 Cairo GMT 2 Moscow GMT 3 New Delhi GMT 5 Bangkok GMT 7 Hongkong Beijing GMT 8 Tokyo GMT 9 Sydney GMT 10 Hawaii GMT 10 Alaska GMT 9 Pacific time GMT 8 American mountain time GMT 7 American mid time GMT 6 American eastern time GMT 5 Atlantic time GMT 4 Brazil GMT 3 Atlantic mid time GMT 2 Update Period The same with the NTP server check interval Default 10minutes Page 39 EMAIL setup lf the alarm is turned on or the alarm linkage photos are taken send an email about the alarm information and the photos to appointed address EMAIL Enable SMTP Server Port Need SSL User Name Password sender Receiver Title Picture 4 21 EMAIL SMTP server Email server address lt could be an IP address or domain name Domain name can be translated only it is the correct DNS configuration Port Email server port number SSL Decide whether using Secure Socket La
20. VR 3 The data line of the hard disk is damaged 4 The hard disk is damaged 5 The hardware of the DVR is damaged There is no audio signal in the surveillance window Possible reasons are as followed Page 59 1 It is not an active tone arm 2 Itis not an active sound box 3 The audio lines are damaged 4 The hardware of the DVR is damaged 9 There is audio signal in the surveillance window but mo audio signal in the playback state Possible reasons are as followed 1 Setting issues the audio option is not chosen 2 The according channel is not connected with the video 10 The time is wrong Possible reasons are as followed 1 Setting is wrong 2 The battery is in bad connection or the voltage is too low 3 The oscillation is damaged 11 The DVR can not control the PTZ Possible reasons are as followed 1 There is something wrong with the frontal PTZ 2 The setting connection or the installation of the PTZ decoder is not correct 3 The connections are not correct 4 The PTZ setting of the DVR is not correct 5 The protocols of the PTZ decoder and the DVR are not matched 6 The address of the PTZ decoder and the DVR are not matched 7 When multiple decoders are connected the far port of the PTZ decoder line A B must connect a 12092 resistance to reduce the reflection otherwise the PTZ control is not stable 8 The distance is too far 12 The motion detect is not working Possible reasons are as foll
21. aintain regularly Page 63 Appendix 1 Remote controller operation 5 X ul 09 1 2 3 4 5 6 7 8 Same function as Multi window button in the front panel Code input number input channel switch Same function as Esc button in the front panel ADD Input the number of DVR to control it Record control Control the record Same function as Record mode Cod Seana AAA A AAA romania MH a Wi Page 64 Appendix 2 Mouse operation Take right hand as an example The mouse in USB connection is supported Os Double click the playback video to zoom in or out the screen Double left click Double click the channel to make it full screen display double click again to goto next channel Left click Choose the according function in the menu Pop desktop shortcut menu in preview state Right click Switch to full screen view when playback Choose the widget or move the item in the widget Set the motion detect area Drag mouse Set the cover area Page 65 Appendix 3 Hard disk capability calculation Make sure the hard disk installed to the DVR for the first time Pay attention to the IDE hard disk lines connection 1 Hard disk capability There is no limit for recording machine We recommend 500G 1000G size to keep better stability 2 Overall capability option The hard disk capability formula is Overall capability M channel number time hour capability in an hour M hour The
22. al lines The high voltage current should be avoided especially Insure the connection stable and credible The signal and shield lines should be firm and connected credible which avoid false and joint welding and oxidation 2 4 2 Video output connections and options The video output is divided into PAL NTSC BNC 1 0Vp p 75Q and VGA output selective configuration When replace the monitor by the computer display there are some issues to notice 1 Do not stay in the turn on state for a long time 2 Keep the computer display normal working by demagnetizing regularly 3 Stay away from the electro magnetic Interference TV is not a credible replacement as a video output It demands reducing the use time and control the Page 8 power supply and the interference introduced by the nearby equipments strictly The creepage of low quality TV can lead to the damage of other equipments 2 4 3 Audio signal input Audio port is BNC connection The input impedance is high so the tone arm must be active The audio signal line should be firm and away from the electro magnetic Interference and connected credible which avoid false and joint welding and oxidation The high voltage current should be avoided especially 2 4 4 Audio signal output Commonly the output parameter of DVR audio signal is greater than 200mv 1KQ BNC which can connect the low impedance earphone and active sound box or other audio output equipments through power ampli
23. d Manual No matter what the present channel is in a state once choose manual button it will have snapshot at related channels Stop No matter what the present channel is in a state once choose stop button it will stop snapshot at related channels Period Set snapshot period it only startup Snapshot Storage at set period Page 27 Type Three types regular detect and alarm Record type Three types regular detect and alarm Regular snapshot at set period Detect snapshot at set period when motion detect video blind and video loss which are preset for snapshot enable Alarm snapshot at set period when alarm in which is preset for snapshot enable Note for related alarm function pls refer to chapter 4 3 4 2 3 Playback Refer to chapter 3 5 2 4 2 4 Backup You can backup the video files to external storage through setup Note The storage must be installed before the file backup If the backup is terminated the already backup can playback individually Backup Index Name Type Remain Total Status Detect 1 USB 382 500 6 OK Backup Cancel Picture 4 3 Backup Detect Detect the storage connected with the DVR such as hard disk or universal disk Backup Click backup button and the dialog box is popped up You can choose the backup file according to the type channel and time Format Format the storage device Page 28 Backup Channel 1 All Start Time By 2012 02 06 00 00 00 quer y End Time E 2012 7 02
24. disk capability and usage information information Code stream Display code stream information System Statistics information Log Display or clear all log information according to the log video and time information Edition Display edition information information Shut down Le Restore reboot Logout shut down or reboot Page 25 4 2 Record 4 2 1 Record Config Set the recording parameters in the surveillance channel The system is set 24 hours consecutive recording in the first startup You can enter main menu gt recording function gt recording setup to set Record Mode CAM 1 PreRecord 5 Sec Mode Config Manual Stop Heek Wed General Detect Alarm Per iodi 00 Per i od2 00 Per 0d3 00 Per iod4 00 Copy To 1 Restore Save Cance Picture 4 1 Record Config CAM Choose the corresponding channel number to set the channel Choose the all option to set the entire channels PreRecord Record 1 30 seconds before the action time length is decided by the code stream Mode Set video state schedule manual or stop Schedule Record according to the set video type common detection and alarm and time section Manual Click the button and the according channel is recording no matter the channel in any state Stop Click the stop button and the according channel stops recording no matter the channel in any state Period Set the time section of common recording The recording will start only in the
25. dows The system date time and channel name are shown in each viewing window The surveillance video and the alarm status are shown in each window ACT IC Table 3 1 Preview icon 3 5 Desktop shortcut menu In preview mode you can right click mouse to get a desktop shortcut menu The menu includes Main Menu Record Mode Playback PTZ Control Color Setting Output Adjust PTZ Tour Logout View1 4 8 9 16 screens Hain Menu Record Mode PlayBack PIZ Control Color setting Output Adjust PIZ Tour Logout Yiew Yie 4 Picture 3 2 Shortcut Menu At the bottom of the interface there is a toolbar to quickly access some general settings 3 5 1 Main menu When you login the system main menu is shown as below Page 14 System a Advanced Cancel Picture3 3 Main Menu 3 5 2 Playback There are two methods for you to play the video files in the hard disk 1 In the desktop shortcut menu 2 Main menu gt Record gt Playback Marec PIC 2012 3 su Mo Tu We Th Fr Sa MENE 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Mol o Ao o ib A cb li ct yee 08 00 12 00 16 00 0 00 Picture 3 4 video playback 1 file type 2 date and time 3 record type 4 channels Page 15 5 Playback control 6 files backup 7 speed hint 8 timeline File type Choose record videos or pictures Date and time Choose the date and time Date with whi
26. e Status Normal means that the hard disk is normal Error means that the hard disk is broken down If the user need to change the damaged hard disk you must shut down the DVR and take up all the damaged hard disks then install a new one Page 48 HDD Management x Index CapacityLeft Cap Status 5 6 2 G Normal In use Format Disk 2 6 1 G Normal Free Cancel Picture4 32 HDD Manage 4 5 2 Account Manage the user purview Note 1 The character length is 12 bytes at most for the following user and user team name Case sensitive 2 There is no limit in the user and user group You can add or delete the user group according to user definition The factory setup include user admin You can set the team as you wish The user can appoint the purview in the group 3 The user management include group user The group and user name can not be the same Each user only belongs to one group Account Index User Name Group Status Modify User 1 C admin admin GUI Modify Group 2 _ guest user Default User Modify Pwd Add User Add Group Delete User Delete Group Cance Page 49 Picture 4 33 Account Modify User Modify the existed user attribute Modify Group Modify the existed team attribute Modify Password Modify the user password You can set 1 6 bit password The blank ahead or behind the char string is invalid The middle blank in the char string is valid Note The user who possess the user
27. e User Delete the current user Choose the user and click delete user button Delete Group Delete the current group Choose the group and click delete group button Page 51 Delete Group admin admin administrator group Picture 4 37 Delete Group 4 5 3 Online User Look up the network user information in the local DVR You can choose the network user and cut the connection Then the user is locked until next boot strap Online User N User Name Login Type Picture 4 38 Online User 4 5 4 TV adjust Refer to chapter 3 5 7 Page 52 4 5 5 Auto Maintain The user can set the auto reboot time and auto file deleting time limit Output Adjust Top Deflate Bottom Def late Left Deflate Right Def late Restore Dave Cance Picture 4 39 Auto maintain 4 5 6 Restore The system restore to the default setup Advanced xq Restore factory settings Restart Immediately Are You Sure to Execute Restore factory settings Cance Picture 4 40 Restore Page 53 4 5 7 Upgrade Upgrade Upgrade Position USB Upgrade file Upgrade Cancel Picture 4 41 Upgrade Upgrade choose USB interface Upgrade file choose the file which needs upgraded Flush Refresh check the backup device 4 5 8 Device Info Provide device interface info like audio in alarm in out to be conveniently used for user Device Info Audio In Channels Alarm In Channels A
28. e strong network communication ability and telecommunication ability The series DVR can be applied in the bank telecom electric power system judicial system transportation intelligent housing factory storehouse water conservancy and so on 1 2 Main functions Real time surveillance analog interface and VGA interface VGA interface is equipped selectively surveillance function through monitor or display Storage non working hard disk dormancy processing which is convenient to radiate heat reduce power and extend the life span special storage format which insures the data safety Compression real time compression by individual hard disk which insures the audio and video signal stable synchronization Backup through SATA interface and USB interface such as USB equipment removable hard disk and so on through net download the files in the hard disk Playback Page 4 individual real time video recording as well as searching playback network surveillance recording check downloading and so on multi playback mode zoom at arbitrary region Net operating through net tele surveillance in the real time tele PTZ control tele recording check and real time playback Alarm linkage multi route relay alarm output which is convenient for the alarm linkage and light control at the spot protecting circuits at the alarm input and output interface which protects the main machine from damage Communication interface RS485 interface which fulf
29. ed 1 Frontvidicon quality is bad The lens is too dirty The vidicon is in backlighting installation 2 The hard disk capability is not enough 3 The hard disk is damaged 22 The downloading files can not play Possible reasons are as followed 1 There is no media player 2 There is no DX8 1 software or higher edition 3 There is no DivX503Bundle exe file to play AVI video files 4 The DivX503Bundle exe and ffdshow 2004 1012 exe files must be installed in the windows xp system 23 I can not remember the advanced code or network code in the local menu operation Please contact the local service or call the HQ service We will offer the service according the machine type and the program edition 5 2 Maintenance 1 Please brush printed circuit boards connectors fans machine box and so on regularly 2 Please keep the grounding well done to prevent the video or audio signal interfered and the DVR from static or inductive electricity 3 Do not pull out the video signal line or RS 232 port or RS 485 port with the power on 4 Do not use the TV in the local video output port VOUT of DVR It will damage the video output circuit easily 5 Do not turn off the switch directly Please use the turn off function in the menu or press the turn off button in the panel 3 seconds or longer to protect the hard disk 6 Please keep the DVR away from heat resource 7 Please keep the DVR ventilated for better heat radiator Please check the system and m
30. er y End Time s 2012 027 06 19 02 28 Remove Index CAM File Name Length 1 2 Picture 3 7 file searching Channel Set the searching channel File type Set the searching file type Start Time Set the searching time scan Playback control Refer to the following sheet for more information a ln Stop Slow play Page 17 jer mf Se e Table 3 2 Playback control key Special functions Single channel view double click the channel to see the single channel and next double click to back Full screen view click the right key to see full screen view O ES AAA and then click play N Accurate playback Input time h m s in the time column button The system can operate accurate playback according to the searching time Local zoom When the system is in single window full screen playback mode you can drag your mouse in the screen to select a section and then left click mouse to realize local zoom You can right click mouse to exit Smart search Click the button to see the next record clip during MD record playback in single channel Zoom timeline Double click the left key on timeline bar to see the record in the hour 3 5 3 Record Mode Please check current channel status a means unchecked lv means checked You can use desktop shortcut menu or click main menu gt recording function gt recording set to enter the recording control interface Record Mode Mode 12 34 Con
31. fier If the sound box and the tone arm can not be isolated howling phenomena is often existed There are some methods to deal with the above phenomena 1 Adopt better directional tone arm 2 Adjust the sound box volume to be under the threshold that produces the howling phenomena 3 Use fitment materials that absorb the sound to reduce reflection of the sound 4 Adjust the layout of the sound box and the tone arm 2 5 Alarm input and output connections 1 Alarm input A Alarm input is grounding alarm input B Alarm input demand is the grounding voltage signal C When the alarm is connected with two DVRs or connected with DVR and other equipments it should be isolated by relay 2 Alarm output Alarm output can not be connected with high power load no more than 1A When forming the output loop it must prevent the big current from relay damage Use the contact isolator when there is a high power load Page 9 3 PTZ decoder connections A The grounding of the PTZ decoder and DVR must be shared otherwise the common mode voltage will lead to the PTZ control failure The shielded twisted pair is recommended B Avoid the entrance of high voltage Make the layout reasonably Take precaution from the thunder C In the outlying end connect 1200 resistance paralleled to reduce the inflection and insure the signal quality D The 485 AB lines of DVR can not connected with other 485 output equipments paralleled E The voltage between
32. fig Manual Stop Record Mode Dave Cance Picture 3 8 Record Mode Page 18 Schedule 1 Record according to the configuration Manual Click the all button and the according channel is recording no matter the channel in any state Stop Click the stop button and the according channel stops recording no matter the channel in any state Record Mode Go to set the record details 3 5 4 Alarm output Please check current channel status gt means unchecked lv means checked You can use desktop shortcut menu or click main menu gt alarm function gt alarm output to enter the alarm output interface Alarm Output Alarm Type Config Manual Stop Status Cancel Picture 3 9 alarm output Configuration Alarm is on according to the configuration Manual Click the all button and the according channel is alarming no matter the channel in any state Stop Click the stop button and the according channel stops alarming no matter the channel in any state 3 5 5 PTZ control Operation interface is as followed The functions include PTZ direction control step zoom focus iris setup operation patrol between spots assistant switch light switch and so on Note1 Decoder A B line connects with DVR A B line Make sure the connection is right before use 2 Click main menu gt system gt PTZ config to set the PTZ parameters 3 The PTZ functions are decided by the PTZ protocols Page 19 PTZ C
33. he data is too much Please stop recording and backup The data exceeds the backup storage The backup equipment is not compatible The backup equipment is damaged The keyboard can not control the DVR Possible reasons are as followed 1 2 4 The serial port of the DVR is not set correctly The address is not correct When multiple transformers are connected the power supply is not large enough Please give each transformer individual power supply The distance Is too far Alarm can not be recessional Possible reasons are as followed 2 3 4 The setting of the alarm is not correct The alarm output is turned on manually The input machine is damaged or the connections are not correct There are some problems for specific program edition Please update the program Alarm is not working Possible reasons are as followed 2 3 4 The setting of the alarm is not correct The connection of the alarm is not correct The alarm input signal is not correct A alarm is connected with two loops synchronously The remote controller is not working Possible reasons are as followed 1 2 3 4 The remote control address is not correct The remote control distance is too far or the angle is too large The battery is used up The remote controller or the front panel of the recording machine is damaged The storage time is not enough Page 62 Possible reasons are as follow
34. hoose list separator of the data format Time Format Choose time format 24 hour or 12 hour Language Support multiple languages with Chinese and English as standards HDD full Choose stop record Stop recording when the hard disk is full Choose overwrite Cover the earliest recording files and continue recording when the hard disk is full Resolution Set display resolution and mode DVR No Only when the address button in the remote controller and the corresponding DVR number is matched the remote operation is valid Video Standard PAL or NTSC Auto Logout Set the latency time in 0 60 O means no latency time DST Choose the summer time option and pop the dialog box as followed Page 35 JEnable IEA y EV Week Begin Jan ist End Jan Ist Picture 4 14 DST week DST N Enable MDate Day of Week Begin pB2010 01 01 00 00 00 End E 2010 7 01 01 100 00 00 Save Cancel Picture 4 15 DST date 4 4 2 Encode setup Set the video audio code parameter video file remote monitoring and so on Set every independent channel s coding parameter in the left part and set the combine encode parameter in the right part Note Combine encode introduces video compression technique which combines and compresses multi channel s video to a special channel Applying for multi channel playback simultaneously Dial up multi channel real time monitor mobile monitor and so on Encode Config
35. ills the alarm input and PTZ control standard ethernet network interface which fulfills the telecommuting function Intelligent operating mouse action function fast copy and paste operating for the same setting Page 5 2 Open package check and cable connections 2 1 Open package check When you receive the DVR please check first First please check whether there is any visible damage to the package appearance The protective materials used for the package of the DVR can protect most accidental clashes during transportation Then please open the box and get rid off the plastic protective materials Check whether there is any visible damage to the DVR appearance At last please open the machine crust and check the data wire in the front panel power wire the connection between the fan power and the main board Front panel and rear panel The key function specification in the front panel and the interface specification in the real panel are in the specification Please check the product type in the front panel whether is accordant with the product type you order The label in the real panel is very important for the after service Please protect it carefully When you contact us for after service please provide the product type and serial number in the label 2 2 Hard disk installation For the first use please install the hard disk 1 disassemble the screw disassemble the cover jix the screw of hard disk Page 6
36. larm Out Channels Cance Picture 4 42 Device Info 4 6 Info 4 6 1 HDD info Display the hard disk state hard disk number video data size picture data size residual capability and so on Page 54 HDD Info Ah 1 Yideo Data 1 000 6 Picture Data 0 234 G Left Capacity 512 G Z Yideo Data 1 000 G Picture Data 0 234 6 Left Capacity i 1 000 6 Cancel Picture 4 43 HDD Info 4 6 2 BPS Display the code stream Kb S and hard disk capability MB H in real time It displays as the wave sketch map Channel Kb S MB ZH Channe Kb S MB ZH Picture 4 44 BPS 4 6 3 LOG Look up system log according to the set mode Log information include system operation configuration operation data management alarm affair Page 55 recording operation user management file management and so on Set the time section to look up and click the look up button The log information will display as a list Press Page up or Page down button to look up and press remove button to clear all the log information Type All Start Time 2012 017 10 00 00 00 End Time 2012 017 10 14 59 30 Log Time User Nam 2012 01 10 06 51 47 admin Clear Log 2012 01 10 52 09 admin Playback 2012 01 10 56 17 admin Add User 2012 01 10 57 16 admin Shut Down 2012 01 10 06 57 30 admin Y ideo Loss CH 1 2012 01 10 06 57 30 admin Yideo Loss CH 2 2012 01 10 06 57 30 admin Y ideo Loss CH 4 2012 01 10 b7 30 admin
37. ng ability Encode frame rate code stream control image quality type code stream value configuration System frame between value video audio enable configuratio Network n Set basic network parameters port DHCP and DNS parameters configuration PPPOE NTP Email IP purview DDNS parameter Set channel name preview hint icon state transparency cover area GUI display time title channel time fold Page 24 PTZ Set channel PTZ protocol address baud rate data bit stop bit check configuration Serial port Configuration Set serial port function baud rate date bit stop bit check RS232 Set patrol mode and interval time Hard disk Show the state of disks in the dvr format disk recover and so on management User Modify user team or password Add user or team Delete user or team management Break the connection with the already login user Lock the account after Online user break until booting up again Manageme TV adjust Adjust TV upside downside nearside starboard distance nt Automatic Set automatic reboot system and automatic deleting files maintenance Resume setup state common setup code setup recording setup alarm Restore setup network setup network service preview playback serial port setup user management Upgrade to upgrade with external device such as USB show quantity information of device interface Hard disk Display hard
38. odify button and enter the channel name menu Modify the channel name The 16 Chinese characters and 25 letters are supportive Time Display 1 Mimeans the selective state Display the system data and time in the surveillance window Channel Title i means the selective state Display the system channel number in the surveillance window Record Status H means the selective state Display the system recording status in the surveillance window Alarm Status Mineans the selective state Display the system alarm status in the surveillance window Bitrate info Mineans the selective state The ninth window displays the code stream information in the nine window preview status Transparency Choose the background image transparency The range is 75 255 Channel Choose the set code output channel number Region Cover Click set button and enter the corresponding channel window You can cover the arbitrary using mouse Gray region is for output Time display and Channel Title Page 45 4 4 6 PTZ setup PTZ Config PTZ Device R5485 Device CAM Protocol Address Baudrate Data Bits stop Bits Parity Cance Picture 4 29 PTZ setup Channel Choose the dome camera input channel Protocol Choose the corresponding dome protocol PELCOD as an example Address Set as the corresponding dome address Default 1 Note The address must be consistent with the dome address Baudrate JCh
39. ontrol 1 CAM 1 PTZ Config Patrol No Zoom Preset l Set Goto Focus amp Name preset00i Melete Exit iris Speed 5 Ptz Trace Picture 3 10 PTZ setup CAM Choose the dome camera input channel Speed Set the PTZ rotation range Default range 1 8 Zoom Clickliml button to adjust the zoom multiple of the camera Focus Click button to adjust the focus of the camera Liris Click button to adjust the iris of the camera Direction control Control the PTZ rotation 8 directions control is supportive 4 directions in Front panel is supportive High speed PTZ Full screen show channel image Left press mouse and control PTZ to rotate orientation Left press mouse and then rotate the mouse to adjust the zoom multiple of the camera Click PTZ Trace to begin Special functions 1 Preset Set a location for the preset calls the preset points PTZ automatically turns to the setting position 1 Preset option Set a location for the preset procedure is as follows Step 1 in Picture 3 10 click the Direction button will turn into preset position Step 2 write the preset points in the input blank and you can also set the name of the point then click the set button The preset point is ok now Step 3 repeat step 1 and 2 to set other preset points Clear Preset Input preset points click Delete button remove the preset Preset point input blank Page 20 PTZ Control 1 C
40. oose the corresponding dome baud rate length You can control the PTZ and vidicion Default 2400 Data bits Include 5 8 options Default 8 Stop bits Include 2 options Default 1 Parity Include odd check even check sign check blank check Default void Page 46 4 4 7 RS232 setup RS232 Function Console Baudrate 115200 Data Bits 8 Stop Bits 1 Parity Cancel Picture 4 30 RS232 setup Serial Port Function Common serial port is used to debug and update program or set up specific serial port Baud rate Choose the corresponding baud rate length Data bits Include 5 8 options Stop bits Include 2 options Parity Include odd even mark space 4 4 8 Tour setup Set the patrol display Mineans that the tour mode is turned on You can choose the single window four windows nine windows sixteen windows patrol display or single display Page 47 Tour Resolution Interval Yiew 1 Alarm Tour Type Interval 5 Return after finished Cance Picture 4 31 tour setup interval Set the patrol switch interval The set range is 5 120 seconds Note means turn off on the patrol 4 5 Advanced 4 5 1 HDD Manage Configure and manage the hard disk The menu displays current hard disk information hard disk number input port status and overall capability The operation include hard disk format resume default Choose the hard disk and click the right function button to execute Clu
41. ording to week or set uniformly Each day is divided into four time sections means the set valid Page 30 Period Cancel Picture 4 6 set the time section Interval Only one alarm signal is turned on even there are several motion detect signals in the set interval Alarm output Start the external equipment of corresponding linkage alarm when the motion detect alarm is turned on Delay Delay a few moments and stop when the alarm state is turned off The range is 10 300 seconds Record channel Choose the recording channel multiple option supportive Trigger the video signal when the alarm is turned on Note Set in the recording setup and perform the linkage recording Start detecting video files in the corresponding time section Tour m means that the selective channel is single window alternate patrol preview The interval is set in the MainMenu gt System gt Tour Snapshot Choose record channels when alarm happens system triggers related channels for snapshot signal Note For Snapshot activation pls go to set period detect and alarm enable at MainMenu gt Record gt Record config PTZ Activation Set the PTZ activation when the alarm is turned on Note PTZ activation is set in the shortcut menu gt PTZ control Set the patrol between spots trail patrol and so on Page 31 PTZ Activation CAM 1 None CAM 2 None CAM 3 None CAH 4 None Cance Picture 4 8 PTZ Activation Delay When alarm is o
42. owed 1 The time range set is not correct 2 The motion detect area set is not correct Page 60 3 The sensitivity is too low 4 Limited by some hardware edition 13 can not login via web or CMS Possible reasons are as followed 1 The system is windows 98 or win me We recommend updating to windows 2000sp4 or higher Version or installing the software for low edition 2 ActiveX is hold back 3 The version is not exceeded dx8 1 Update the display card driver 4 Network connection failure 5 Network setting issues 6 Invalid password or user name 7 The CMS is not matched the DVR program version 14 The image is not clear or there is no image in network preview state or video file playback state Possible reasons are as followed 1 Network is not stable 2 The user machine is resource limited 3 Choose the play in team mode in the network setup of DVR 4 The region shelter or channel protection is set 5 The user has no surveillance purview 6 The real time image of the hard disk recording machine itself is not clear 15 Network connection is not stable Possible reasons are as followed 1 Network is not stable 2 IP address is conflicted 3 MAC address is conflicted 4 The net card of the DVR is bad 16 There is something wrong with the USB backup or writing a CD Possible reasons are as followed 1 The rewritable machine and the hard disk are shared the same data lines Page 61 17 18 19 20 21 5 T
43. p FTP is available only when alarm happens or alarm activates record and snapshot it will upload related record and snapshot pictures to FTP server FTP Enable server IP Port User Name Password Anonymous Max File Length DirName Cancel Picture 4 24 FTP setup Enable Click Enable then all settings will be available Server IP IP address for FTP server Port Domain Port of FTP default 21 User Name User name of FTP Password Password of user Max File Length Max length for upload files at every packed default 128M DirName Directory of uploading files Wireless Config ADSL through 3G net card use CMS to visit and config the device Page 42 Wireless Enable Type Auto Wireless AP Dial Number User Name Password IP Addr Cancel Picture 4 25 Wireless Config Enable Choose Enable to make all settings available Type Dial type default AUTO Wireless AP 3G access point Dial Number 3G Dial Number User Name User name of 3G Password Password of dial user IP Address IP address got from dial UPNP UPNP protocol can auto port forwarding on router make sure UPNP is running on router before use it UPNP Enable HTTP Port TCP Port Mobile Monitor Make sure UPNP is running on rout Cance Picture 4 27 Page 43 Enable Choose Enable to make sure all UPNP settings available HTTP Route will automatically distribute HTTP port for the device when IE viewing it need
44. set range Copy to copy the current channel settings to other channels Record type Set recording type regular detection or alarm Regular Perform the regular recording in the set time section The video file type is R Detect Trigger the motion detect camera mask or video loss signal When above alarm is set as opening recording the detection recording state is on The video Page 26 file type is M Alarm Trigger the external alarm signal in the set time section When above alarm is set as opening recording the detection recording state is on The video file type is A Restore restore the record configuration to default Note Refer to chapter 4 3 to set corresponding alarm function 4 2 2 Snapshot Storage Setup snapshot parameters for different channels It s set stop in default For more details pls go to Main Menu gt Record gt Snapshot Storage for appropriate settings SnapShot Storage CAM 1 Interval 10 Sec Mode Config Manual YIStop Week General Detect Alarm Per iodi Per iod2 Per iod3 Per iod4 Copy To Restore Save Cancel Picture 4 2 Snapshot storage CAM Select the related channel to set click all to set all channels Interval Setup interval time between two snapshots default is 5 sces Mode Set record status Schedule Manual and Stop Schedule Realise snapshot according to record type regular detect and alarm and perio
45. t PTZ tour start cruise PTZ begins to work on the cruise line Click Stop cruise to stop cruise You can also click the start stop button In Picture 3 11 to start or stop the cruise 3 5 6 Color setting Set the selective image parameters current channel for single window display and cursor place for multi window display You can use the desktop shortcut menu and enter the interface The image parameters include tonality brightness contrast saturation You can set different parameters at different time sections Color Settingl M00 00 24 00 Brightness il 64 Contrast ll 64 Hue 2 Saturation 64 Copy To Copy Default Colo Save Cancel Picture 3 18 Color Setting Page 22 3 5 7 Output Adjust Adjust TV output area parameters You can use the desktop shortcut menu or enter main menu gt management tools gt Output adjust Output Adjust Top Deflate Bottom Def late Left Deflate Right Deflate Restore Cancel Picture 3 19 Output Adjust 3 5 8 Logout Restore logout shut down the system or reboot up You can use the desktop shortcut menu or enter main menu Logout E O Restore Logout Shutdown Reboot Reboot Cancel Picture 3 20 Restore Reboot Logout Shutdown Reboot the system restore reboot Resume setup state and reboot the system logout Quit the menu Offer password next entrance shut down Quit the system Turn off the power supply When press the shut down button there
46. te border means the system date Red background means this day has record files Record type Normal motion detect alarm or others In the video searched green means normal yellow means motion red means alarm Channels Choose the channels to display Speed hint show the fast or slow playback speed File backup Go to backup files Click the button and operate as followed Note The storage must be installed before the file backup If the backup is terminated the already backup can playback individually Backup Index Name Type Remain Total Status Detect 1 USB 382 500 6 OK ERT Cancel Picture 3 5 detect the storage Detect Detect the storage connected with the DVR such as hard disk or universal disk Backup Click backup button and the dialog box is popped up You can choose the backup file according to the type channel and time Page 16 Backup Channel 1 All Start Time By 2012 02 06 00 00 00 quer y End Time s 2012 027 06 119 00 42 Remove Index CAM File Name Length OO NS HD OA Ww ni Cancel Picture 3 6 recording backup Remove Clear the file information Search Search the file according to the searching parameter Begin Click the play button to start the backup Cancel During backup you can exit the page layout to carry out other functions File searching Search the file according to the searching parameter Backup Channe 1 All Start Time Ry 2012 7 02 06 00 00 00 qu
47. ver recording will last some seconds 10 300sec then stop Show message Pop the alarm information dialog box in the local host computer screen Send EMAIL lv Imeans sending an email to user when the alarm is turned on Note Set in the NetService and send email FTP upload lv Imeans upload the alarm images to your ftp when the alarm is turned on Buzzer Device buzzers when dvr detects alarm 4 3 2 Video Blind When the video image is influenced by the environment such as bad brightness or reaching the set sensitivy parameter the camera mask function is turned on and the linkage function is turned on Yideo Blind CAM Enable sensitivity Period Alarm Output Record Channel Tour Snapshot PTZ Activation Delay show Message send Emai Buzzer FIP upload Copy To Copy Restore Save Cancel Picture 4 9 Video Blind Set method refer to chapter 4 3 1 Motion detect 4 3 3 Video Loss When the equipment can not obtain the channel video signal the video loss alarm is turned on and Page 32 the linkage function is turned on Yideo Loss CAM Enable Y Per od Alarm Output Record Channel Tour Snapshot PTZ Activation Set Delay Show Message Y Send Emai Buzzer FIP upload Copy To Copy Restore Save Cancel Picture 4 10 Video loss Set method refer to chapter 4 3 1 Motion detect 4 3 4 Alarm input When the equipment obtains the external alarm signal the alarm function is turned on
48. wer failure 2 Replace the hard disk Before replacing the hard disk the power supply switch in the real panel must be turned off 3 Replace the battery Before replacing the battery the setting information must be saved and the power supply switch in the real panel must be turned off The DVR uses button battery The system time must be checked regularly If the time is not correct you must replace the battery we recommend replacing the battery every year and using the same battery type Note The setting information must be saved before replacing the battery otherwise information will lose 3 3 System Login When the DVR boots up the user must login and the system provides the corresponding functions with the user purview There are two user settings The names are admin and guest and these names have no password Admin is the super user purview guest s permissions are preview and video playback User admin and guest s password can be revised while their permissions can t be revised SYSTEM LOGIN User Name ladmin Password Please Login OK Cancel Picture 3 1 System Login Password protection If the password is continuous wrong ten times the account will be locked Through reboot or after half an hour the account will be unlocked automatically For your system security please modify your password after first login Page 13 3 4 Preview You can right click mouse to choose the switch between the win
49. yer protocol to login User Name Apply the email server user name Password Iinput the password corresponding to the user Sender Set the email sender address Receiver Send the email to appointed receivers when the alarm is turned on You can set three recelvers at most Title You can set as you wish IP Filter setup When choosing the white list only the listed IP address can connect the DVR The 64 IP addressed are supportive in the list When choosing the black list the listed IP address can not connect the DVR The 64 IP addressed are supportive in the list Page 40 You can delete the set IP address by y in the options Note When the same IP address is in the white and black list at the same time the black list precedence is higher IP FILTER Enable Restricted Banned IP bd Cance Picture 4 22 IP IP FILTER DDNS It is the abbreviation of dynamic domain name server DDNS Type choose ddns service provider User name Provide the account registered by DDNS Password Provide the password registered by DDNS When the DDNS is successfully configured and start you can connect the domain name in the IE address column to visit Domain name Provide the domain name registered by DDNS Note The DNS setup must be configured correctly in the network setup DDNS DONS Type 332 Enable Pi User Name user name Password KEEEEE Domain Name xxx 3322 org Enter Picture 4 23 DDNS setup Page 41 FTP setu
Download Pdf Manuals
Related Search