Owners Manual F Series 3-Hole
Contents
1. LOGGeERING OWNER S MANUAL TRAIL BLAZERS and D SERIES TRACKS LOEGERING 800 373 5441 15514 37 Street SE 701 347 5441 Casselton ND 58012 USA Fax 701 347 4323 E Mail Imi loegering com Internet www loegering com Owners Manual Track F amp D Series 3 Hole Lit 0001 doc l 02 25 05 LIMITED WARRANTY AND DISCLAIMER OF WARRANTIES Loegering Mfg Inc warrants its Tire Crawlers tracks against operational failures caused by defective material or workmanship which occur during normal use within fifteen 15 months from the date of purchase or twelve 12 months from the date the product is first put into service whichever is earlier Your sole remedy under this Warranty is repair or replacement of the Tire Crawlers tracks that are determined by Loegering Mfg Inc to be defective in material or workmanship Any modifications welding cutting etc to the machine tracks or track accessories without proper authorization will void the warranty Written authorization for any return of goods on a warranty claim must first be obtained from Loegering Mfg Inc All returns must be accompanied by a Returned Material Authorization Number RMA and a written explanation of claimed defects with the exact circumstances of operational failure Any product returned for warranty inspection must be shipped prepaid and will be returned freight collect All costs of product removal and product installation are at the customer s expense Loeger2. dealer or Loegering If track appears to be too long Shorten the track by changing links in the long position to the short position If all the links are in the short position remove one pad and continue with procedure for short track Diagram 6 To remove a pad section one pad and two adjoining links Remove four Dura Pin assemblies For an extremely worn track it may be necessary to pull adjoining pads together to remove pin Remove the pad and two adjoining links Reposition loose track and reinstall two Dura Pin assemblies Torque Dura Pin nuts to 80ft lbs 5 ft lbs Save remaining parts for later use 8 To connect ends of track install Dura Pins in links Torque nuts to 80 ft lbs 5 ft lbs 9 Remove installation tool and slowly drive machine back and forth allowing track to pass through at least two complete revolutions Verify that track is not striking machine A properly adjusted track must have one to three inches of sag Diagram 7 10 Unroll second track and change links to match those of the first track installed 1 to 3 sag 11 Repeat instructions 3 through 10 for track not yet installed 12 Return machine to its normal operating configuration Diagram 7 13 CHECK TRACK TO TIRE FIT With tires inflated to maximum recommended air pressure load machine to normal operating weight Shut off machine and check track fit Diagram 8 Area A must not compress tire side wall Area B may compress corners of tread withou
3. e until track is pulled over around and under the tandem wheels Stop when last pad lifts off ground and is starting to get pulled up front tire Diagram 2 Diagram 5 Chain or tie ends of track together with installation tool Continue backing machine until ends of track are between wheels Diagram 3 Remove chain or rope Diagram 4 6 Mount installation tool as shown in Diagram 4 02 25 05 Owners Manual Track F amp D Series 3 Hole Lit 0001 doc 4 7 Tighten track using a wrench or breaker bar socket arrangement not longer than 18 inches CAUTION Use of a tool or cheater bar longer than 18 may result in personal injury or death and will void installation tool warranty lt may be necessary to slowly rock machine back and forth while occasionally stopping to tighten track This will help take up excess slack Diagram 5 In the track Regular Link Dura Pin lf track appears to be too short Measure distance A at track ends Diagram 6 Round to next whole number i e 3 rounds to 4 This is the number of link locations to extend track will be lengthened the same number of inches NOTE If multiple links need to be lengthened it is best to drive out of track and make adjustments on the ground Torque Dura Pins nuts to 80 ft lbs 5 ft lbs Diagram 6 If rounded number is greater than the total number of links in the short position an additional pad is required Contact your local
4. eels and torque nuts to the manufacturer s recommended specification 6 Failure to follow these instructions will void the warranty on the spacers GUSSET GUARD INSTALLATION INSTRUCTIONS MELROE 7753 and 773 ans A GUSSET J Figure 1 Figure 2 Qty Part Number Description LN81 1 Gusset Guard Assembly 1 LM812 Gusset Guard Left 1 LM811 Gusset Guard Right 2 PD0170 1 5BP 1 2 13UNC x 1 1 2 Bolt 2 PH0170 1BP 1 2 13UNC Nut 2 PJ0170 3 2BP 1 2 Lock Washer Step 1 Raise machine block and remove right front wheel per machine manufacturer s instruction WARNING Failure to use adequate blocking or jack stands could result in injury or death NOTE Wheel spacers if required should be installed at this time Step 2 Position right gusset guard on right gusset such that it is against the gusset and fender as shown in Figure 2 Step 3 Using a C clamp or locking pliers clamp the gusset guard firmly in place Step 4 Mark the location of the holes Step 5 Remove the clamp s and gusset guard Step 6 Drill two 9 16 diameter holes Holes are 312 on center Step 7 Reposition gusset guard Insert bolts so that the nuts will be inside the gusset Install lock washers and nuts Supplied Torque to 70 to 80 ft lbs Step 8 Replace wheel and repeat process for the left side of the machine Loegering 15514 37 Street SE L OEGERING Casselton ND 58012 USA Ph 800 373 5441 a Fax 701 347 4323 Warranty Registration F
5. ing Mfg Inc does not warrant that its Tire Crawlers tracks will meet your requirements nor does it assume responsibility for costs and or damages resulting from use Since tire size often varies from the stated size the customer is solely responsible for checking track to tire fit and or providing proper clearance and safety shielding There are no other warranties THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF AND TO THE EXCLUSION OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY LOEGERING MFG INC ITS EMPLOYEES OR DEALERS SHALL ALTER MODIFY OR INCREASE THE SCOPE OF THE ABOVE WARRANTY OR CREATE ANY NEW WARRANTIES Some states do not allow the exclusion of implied warranties so the above exclusion may not apply to you In that event any implied warranties are limited in duration to ninety 90 days from the date of delivery of our Tire Crawlers tracks This Warranty gives you specific legal rights You may have other rights which vary from state to state LIMITATIONS OF REMEDIES Loegering Mfg Inc s entire liability and your exclusive remedies shall be repair or replacement of the Tire Crawlers tracks for any alleged breach failure or malfunction Regardless of whether any remedy set forth herein fails of its essential purpose in no event will Loegering Mfg Inc be liable to you fo
6. loose paint etc Failure to remove all foreign material will cause the spacers to become loose resulting in damage to the spacer and or studs 2 Inspect spacers for any excessive paint or foreign material prior to installation 3 Install soacers Spacer should fit easily on wheel hub if there is any interference contact Loegering before reinstalling wheels 4 Reinstall wheels and torque nuts to the manufacturer s recommended specification NOTE If reach nuts are supplied with the spacers use them in lieu of the nuts removed from the machine Save the nuts removed from the machine so that the wheels may be reinstalled when the spacers are removed 5 Failure to follow these instructions will void the warranty on the spacers INSTALLING SPACERS WITH STUDS 1 Remove wheels and thoroughly clean the hub flange surface of all foreign materials including dirt grease loose paint etc Failure to remove all foreign material will cause the spacers to become loose which will result in damage to the spacer and or studs 2 Inspect spacers for any excessive paint or foreign material prior to installation 3 Install soacers Spacer should fit easily on wheel hub if there is any interference contact Loegering before tightening nuts 4 Tighten nuts evenly to allow spacer ring to center itself on tapered nuts Torque 1 2 nuts 85 to 95 ft lbs 9 16 nuts 110 to 130 ft lbs and 5 8 nuts 165 to 185 ft lbs 5 Reinstall wh
7. orm Please complete and return to Loegering to validate warranty Purchase Date Form Completion Date Order Dealer Name Contact Name Address City Zip Phone Number Fax Number Email Address Contact Name Address State Zip Phone Number Fax Number Email Address Part Number Description Serial Number Model s Was there evidence of damage upon receipt Yes j No lf yes explain Tell us about the equipment you plan to use your new attachment on Tire Size tracks only Hours of use on machine prior to installation of attachment Hours Hour information is very important to warranty resolution Warranty may not be valid without completion of this section Application description
8. r any special consequential indirect or similar damages including any claimed damage to person except in the case of consumer goods or other property any lost time or lost profits arising out of the use or inability to use the Tire Crawlers tracks Some states do not allow limitation or exclusion of liability for incidental or consequential damages so the above limitation or exclusion may not apply to you Owners Manual Track F amp D Series 3 Hole Lit 0001 doc 2 02 25 05 LOGGeERING ww_ Loegering 15514 37 Street SE Casselton ND 58012 USA Ph 800 373 5441 Fax 701 347 4323 TRAIL BLAZERS F AND D SERIES PARTS LIST Ref Part Number 1 FN103 11 1A 1 FN103H 11 1A 1 FN103 12 5A 1 FN103H 12 5A 1 FN103 13 2A 1 FN103H 13 7A 1 FN103H 15 5A 1 DN103 Pad Width A 1 DN103H Pad Width A 2 FN425 2 FN424 3 400660 3 400670 4 PH0171 5CP Weight LB KG 12 4 5 6 12 6 5 7 12 8 5 8 13 0 5 9 13 1 5 9 13 3 6 0 13 8 6 26 N A N A 6 3 8 4 13 06 14 06 02 01 Note These track series use Installation Tool P N YN601 Pad width distance between the two inner link plates Owners Manual Track F amp D Series 3 Hole Lit 0001 doc Description Pad Weldment 11 125 Standard Link Style Pad Weldment 11 125 Heavy Link Style Pad Weldment 12 5 Standard Link Style Pad Weldment 12 5 Heavy Link Style Pad Weldment 13 25 Standard Link Style Pad Weldment 13 75 Heavy Link S
9. t any problem Clearance at both points is acceptable unless track is able to wander far enough to strike machine Diagram 8 NOTE Track will require one or more length adjustments during break in period dependant upon operator usage See REMOVING TIRE CRAWLER TRACKS for specific removal instructions REMOVING TIRE CRAWLERS TRACKS 1 TO AVOID DEATH Raise and block boom according to machine manufacturer s instructions allowing safe access to front of machine Turn off machine when its operation is not necessary for track removal process 2 Using a wrench or socket set loosen two nuts on two opposing Dura pins NOTE For machines with limited clearance drive forward so nuts can be loosened easily from the front do not remove the nuts yet Drive back again to center Dura pins on top between tires 3 Feed hook end of installation tool down between pads ahead of loosened Dura pins position winch assembly on pad Position hook on opposing pad See Diagram 5 of INSTALLING TIRE CRAWLERS TRACKS 4 Using a1 1 8 wrench or breaker bar socket arrangement not longer than 18 operate the installation tool until tension is relieved and adjuster link assembly moves freely CAUTION Use of a tool or cheater bar longer than 18 may result in personal injury or death and will void installation tool warranty 6 Remove the two Dura pins and nuts Carefully loosen installation tool until track ends lay on tires Remo
10. tyle Pad Weldment 15 5 Heavy Link Style Pad Weldment Standard Link Style Pad Weldment Heavy Link Style Link 3 Hole Standard 1 2 Link 3 Hole Heavy 5 8 Dura Pin Standard Link Style Dura Pin Heavy Link Style Jam Nut 12 NF Gr 8 02 25 05 Loegering 15514 37 Street SE Casselton ND 58012 USA LoEGERING Casselton ND 58 Fax 701 347 4323 INSTALLING TIRE CRAWLERS TRACKS TRAIL BLAZERS F SERIES NOTE Any modifications welding cutting etc to machine tracks or track accessories without proper authorization will void warranty See Limited Warranty for further details Trail Blazers are not recommended on solid rubber foam filled segmented aircraft and some styles of tires call Loegering Every track includes an installation tool P N YN601 1 Install idler system or axle assembly for your specific model of equipment 2 Inflate tires to maximum recommended air pressure check pressure regularly Diagram 1 3 Unroll track on a level surface and divide into two equal sections Tip one track over so side plates are in contact with the ground Fold first 3 or 4 pads back and drive machine forward until one front tire is positioned between track side plates and just touches pad bottom Lay pads back onto tire and attach a rope or chain on end pad Run rope or chain over front and back tires and tuck it under back tire Diagram 1 4 While an assistant observes slowly back machin
11. ve installation tool 7 While an assistant observes from a safe distance drive machine forward until track can be removed from front tire Do not allow end of track between tires to go under rear tire Carefully lower track off the front tire CAUTION To avoid injury do not stand in front of track as it is lowered 8 Slowly back machine off the track Repeat procedure for other side 9 Return machine to normal operating configuration NOTE Accessories wheel spacers boom stop etc may remain on machine PIN WEAR GAUGE To determine if the track requires new pins remove a pin and slide the worn area into the gauge located on the winch portion of the installation tool If the pin slides into the gauge it is time to replace the pins Contact your dealer for replacement parts Loegering LOGEGeERING 15514 37 Street SE Casselton ND 58012 USA Ph 800 373 5441 Fax 701 347 4323 TRAIL BLAZERS F amp D SERIES INSTALLATION TOOL PARTS LIST ITEM QTY PART NUMBER DESCRIPTION YN601 Installation Tool Trail Blazer amp D Series 1 1 YN501 Winch 2 2 1 YN502 60 Webbing 2 x 60 3 1 YN603 Base Plate 4 1 YN606 Hook 5 1 YN607 Wedge 6 2 PH0O170 1BP Nut 2 13UNC Gr 5 Plated 7 2 PD0170 1BP Bolt 1 2 13UNC x 1 Gr 5 Plated WHEEL SPACER INSTALLATION INSTALLING SPACERS WITHOUT STUDS 1 Remove wheels and thoroughly clean the hub flange surface of all foreign materials including dirt grease
Download Pdf Manuals
Related Search