User Guide
Contents
1. other vehicles the windshields tint lines and large buildings e The vehicle s shape Vans generally have poorer range e The shape of the vehicle s roof and the A pillars cause considerable radio frequency deflection As a result the direction in which the vehicle is facing with relation to the remote transmitter can affect range Facing the front of the vehicle generally produces the greatest range secondly facing the back Facing either side of the vehicle will usually give the poorest range e The range will be significantly poorer in crowded parking lots as opposed to empty parking lots e Hold the transmitter at shoulder height or hold it against your chin so your body acts as a larger antenna e The operating range will be somewhat poorer on vehicles equipped with a factory alarm or key less entry system FAILED REMOTE START There are several different installation factors and devices that must work together in order for your vehicle to Remote Start properly In some cases a failed Remote Start is not the fault of the Remote Starter itself Here are some things to consider when the Remote Starter fails e Unmaintained Engine If you have problems starting the vehicle with the key then the Remote Starter will have the same difficulty e Low Battery A battery s voltage can drop to less than 4 volts DC 1 3 of the original during cold weather starting Ensure your battery is working properly and is able to provide the proper c2. the Security Lock will re arm the OEM anti theft system in order to return the vehicle to its original protective state TRUNK HATCH RELEASE ZONE 6 The vehicle s trunk or rear hatch if installed can be opened by pressing the TRUNK button for 3 seconds RUNTIME On gas engines the Remote Starter can run the vehicle for either 3 7 or 15 default minutes On diesel engines the Remote Starter can run the vehicle for either 6 15 or 30 default minutes RUNTIME RESET Once the vehicle is running with the Remote Starter the runtime can be reset before it expires at any time by pressing the START button while the vehicle is Remote Started The horn siren will sound once to confirm If installed ALARM AUDIBLE CONFIRMATION By default the Alarm will not send an audible confirmation horn siren after the first signal has been received from the remote transmitter s SILENT Press the LOCK or UNLOCK button ONCE and the park lights will flash but the horn siren will NOT confirm the signal AUDIBLE Pressing the same button TWICE consecutively LOCK or UNLOCK the park lights will flash and the horn siren will confirm the signal The Alarm can be programmed to audibly confirm the signal on the first button press See Installation Guide ALARM ACTIVITY The following characteristics enhance your vehicle s security If the Alarm system is active and the horn siren is sounding e Press the UNLOCK button ONCE to stop the a
3. 16 DRIVING OFF When the vehicle is running with the Remote Starter enter the vehicle and proceed with the following STEP 1 Insert the key and turn it to the ignition ON Run position Warning Do not turn the key to the START position when the engine is running This may damage the ignition system on some vehicles SA Step on the brake pedal to disable the Remote Starter and put the vehicle in gear CANCELLING A REMOTE START See USING THE REMOTE CONTROL page 4 REMOTE STARTER FEATURES IDLE MODE AUTOMATIC TRANSMISSION Idle Mode allows the vehicle to run without the key in the ignition barrel For example if you stop for a quick errand or delivery simply allow the vehicle to run while you are gone The engine will run until the Remote Starter runtime expires Press START any time the vehicle is running with the Remote Starter to reset this timer To activate Idle Mode automatic transmission proceed with the following steps With the key in the barrel at the ignition ON RUN position and the en gine running press the START button until the parking lights turn on B 7 Turn the key to the OFF position and remove the key from the ignition barrel The vehicle will continue to run with the Remote Starter The engine will continue to run until either the remote stop function is pressed see USING THE RE MOTE CONTROL page 4 the Remote Starter runtime expires the parking brake is disengaged the brake is press
4. NSMISSION Turbo Mode if installed is similar to Idle Mode but is used to cool down the turbo charger once the driver leaves the vehicle The Remote Starter will continue run the vehicle for 2 minutes allowing the turbo charger to cool down To activate Turbo Mode automatic transmission proceed with the follow ing steps With the engine already running press the remote START button until 1 the parking lights come on STEP 2 Remove the key from the ignition barrel lt lt The vehicle will continue to run with the the Remote Starter STEP 3 Exit the vehicle and close all of the doors ON The vehicle will continue to run after all the doors are closed E A o Press the LOCK button to lock the doors The vehicle will continue to run for 60 seconds TURBO MODE MANUAL TRANSMISSION Turbo Mode if installed is similar to Idle Mode but is used to cool down the turbo charger once the driver leaves the vehicle The Remote Starter will continue run the vehicle for 2 minutes allowing the turbo charger to cool down To activate Turbo Mode manual transmission proceed with the following steps See IDLE MODE MANUAL TRANSMISSION page 7 VALET MODE VIA SWITCH VALET CODING Valet Mode disables both the Remote Starter and Alarm system Whenever the vehicle is being serviced or repaired or the vehicle is parked indoors it is mandatory that Valet Mode be enabled to prevent an accidental Remote Start Note The alarm system is not active in
5. SECURITY SYSTEM ONLY REMOTE CAR STARTER ONLY SECURITY SYSTEM AND REMOTE CAR STARTER AUTOMATIC MANUAL TRANSMISSION 1 WAY REMOTES FTX64 1W User Guide Model FTX 64 2W Model ANT FMH 2W FCC ID 2ACKU R2WO1FM FCC ID 2ACKU A2WO1FM IC 12084A R2WO1FM IC 12084A A2W01FM Manufacture Manufacture FORTIN ELECTRONIC SYSTEMS FORTIN ELECTRONIC SYSTEMS DESIGNED amp ENGINEERED IN CANADA DOC 20141209 REV 3 2014 ALL RIGHTS RESERVED TABLE OF CONTENTS INMI RN ra oa 2 RTI MARIAN aaa RENA 3 PTE ot ence sce il i AR At desea eee E Gas i 3 INDUSTRY CANADA USER NOTICE resonante 3 GOVERNMENT REGULATIONS asicssensioiieucoemvsdenstnsnsveatin nie ccietvoscthinivingisniiish circa ubvevsisbutien 3 USING THE REMOTE CONTRO Losantos a a 4 REMOUTE STARTING ida cto ca aan 5 REMOTE STARTING THE VEHICLE Serisini Saas E E EE 5 Ce o Lana A T E E E ie ee oneal 5 READY MODE MANUAL TRANSMISSION ONLY scsscssssssessessessecseesecsuesesuesueesessecseeseeessessnsaneenseneenes 5 INC acest rset sn eerie nied art teni 7 ANG IT VGA REMOTE SIA scaner caia 7 PCIE TEs CARERS FEATURES coso 7 DLE MODE AUTOMATIC TRANSMISSION estancada 7 IDLE MODE MANUAL TRANSMISSION c cssssessessesseessessessesseeseesecsecssssnsensesesuseseeseeseeseeesssesaneensensenes 7 TURBO MODE AUTOMATIC TRANSMISSION ssecsessessesssessessecsecsecsesecsnsssssuesseenecseesssessnssneaneeneaneensen 8 TURBO MODE MANUAL TRANSMISSION sssssessessesstessessesues
6. Starter Alarm can control most electronic sys tems within the vehicle A WARNING This Remote Starter must be installed by a trained professional Improper modifications to any of the following settings could adversely affect the reliability of the Remote Starter and or the vehicle s operation Configurable Options Remote Door Locks Active or Passive Arming Ignition Door Locks Security Lock Trunk Hatch Release Runtime Runtime Reset Secure Transmitter Mode REMOTE DOOR LOCKS If the Remote Starter is installed with door locks you will be able to lock and unlock the vehicle without using the key or OEM key fob To UNLOCK the doors and DISARM the Alarm The parking lights will flash twice and the LED will turn OFF to confirm the signal The Starter Kill will also deactivate allowing TI k ps pad the vehicle to be started with the key If UNLOCK is pressed again consecutively the horn will honk twice if installed to confirm Note The system can be configured during installation so the horn confirms UNLOCK on the first attempt ond To LOCK the doors and ARM the Alarm The parking light will flash once and the LED will turn ON to confirm the signal The Starter Kill will activate preventing the T Press the LOCK but vehicle from being started with the key If LOCK is pressed again ton for 0 5 second consecutively the horn will honk once if installed to confirm Note The system can b
7. cluding Starter Kill when the system Is in Valet Mode However you are still able to lock and unlock the doors and release the rear hatch trunk Note When the Remote Starter Alarm is in Valet Mode the LED will stay ON solid instead of flashing after the doors are locked The LED will turn off only after the Remote Starter Alarm exit Valet Mode The valet mode can be programmed to use a coded entry in order to increase the security of your alarm system and to prevent accidents By default the valet button is pressed 3 times after turning the igni tion Function 30 can be programmed to use a coded value instead of the default one Page 8 16 VALET CODING DISBALED DEFAULT To activate and deactivate Valet Mode using the valet switch proceed with the following steps TB Ne Insert the key and turn it to the ignition ON RUN position The vehicle ard O does not need to be started STEP 2 X3 Within 10 seconds press 1 second and release the Valet switch 3 times STEPS BWB Valet mode enabled The LED is ON Valet mode disabled The LED is OFF VALET CODING ENABLED OPTIONAL To activate and deactivate Valet Mode using the valet switch proceed with the following steps a ay os Insert the key and turn it to the ignition ON RUN position The vehicle does not need to be started STEP 2 Within 10 seconds press and release the valet button 3 to 7 times X X X valet code for 1 second If your valet code is 7 then press and re
8. e configured during installation so the horn confirms LOCK on the first attempt ACTIVE OR PASSIVE ARMING Passive Mode will allow the Alarm to automatically rearm itself 60 seconds after it is disarmed if no door s or trunk are open ed Opening a door before the 60 seconds has expired will reset the timer but will also prevent the Alarm from locking the doors This option is enabled by default and the Alarm will never arm as long as at least one door is left open When this feature is disabled the Alarm is con sidered to be in Active Mode which requires the remote transmitter to arm the Alarm Note The automatic rearm can be deactivated by pressing the UNLOCK button Page 11 16 IGNITION DOOR LOCKS Ignition Door Locks is an automatic passenger safety feature When enabled the Remote Starter Alarm will automatically LOCK the vehicles doors once the key is turned to the ignition ON RUN position and the brake pedal is pressed The Remote Starter Alarm will also automatically UNLOCK the vehicles doors once the key is turned to the OFF position SECURITY LOCK Security Lock triggers the vehicle s door locks after the Remote Starter has shut down In some cases before the Remote Starter is able to start the vehicle it must disarm the Original Equipment Manufac ture OEM anti theft system first if equipped to prevent a false alarm when the vehicle is running After the Remote Starter runtime has expired and the Remote Starter shuts down
9. e running STEP 1 B 135 Make sure that all doors are closed and the transmission is in the onat i NEUTRAL position a gt Engage the parking brake A De anne a A Release the brake pedal A A agen a epee ee ese eee Press the START button for 3 seconds The parking lights will flash once and then remain on a ale Ae i E EEEE tn ee E PE T a 7 Remove the key from the ignition barrel QO The vehicle will remain running with the Remote Starter PIERS Exit the vehicle and close all of the doors y The Remote Starter will stop running once all the doors are closed METHOD 2 This method must be programmed by the installer during installation THIS METHOD WILL ACTI VATE THE REMOTE STARTER SEQUENCE EVERYTIME THE END USER IS LEAVING THE VEHICLE AUTOMATIC AC TIVATION The vehicle must be running STEP 1 1a 5 Make sure the transmission is in the NEUTRAL position 246 STEP gt all 4 Engage the parking brake STEP a Po Release the brake pedal A STEP 4 Remove the key from the ignition barrel The engine will shut down and the vehicle will be ready to start at any time STEP 5 T l DE Exit the vehicle and close all of the doors The Remote Starter will stop running once all the doors are closed TO DEACTIVATE READY MODE e Open any door s e Open the hood e Disengage of the parking brake Note If the parking lights flash 3 times when Remote Starting Ready Mode is not enabled Page 6
10. e start the vehicle when the tempeture is below 5 C 23 F every 1 5 or 3 hours and run for 3 5 7 or 15 minutes 6 14 or 30 for diesel engines depending on programming The remote starter will repeat this sequence for up to a maximum of 24 hours For manual transmission vehicle s READY MODE must be enabled and if at any time READY MODE is disabled this sequence will cancel A WARNING Do not start the vehicle indoors garage underground parking To enable Cold Start Timer Mode proceed with the following steps Press and release the FUNCTION button within 12 seconds Jo simultaneously press and and hold the LOCK and START buttons for 1 second To disable Cold Start Timer Mode do any of the following e Press and release the FUNCTION but Put the Remote Starter e Turn the key to the ignition ton within 12 seconds to simultane alarm into Valet Mode ON RUN position ously press the LOCK and the START Remote Start the vehicle e Disable Ready Mode buttons for 1 second until the parking Open the hood manual transmission light flash twice e Press the brake pedal Note If the Alarm is triggered during Remote Start Cold Start the vehicle will stop running but Cold Start will not cancel it s schedule AUXILIARY USE Aux 1 Drivers side sliding door if installed Press and relase the FUNCTION the remote LED flashes slowly white button gt within 12 seconds press the bu
11. ed or the hood is opened If the Remote Starter is shut down by transmitter it will automatically go in to Ready Mode if all the doors are closed A WARNING Never leave children or animals in a Remote Started vehicle unattended IDLE MODE MANUAL TRANSMISSION Idle mode is activated in much the same way Ready Mode is activated except for Step 1 To activate Idle Mode manual transmission proceed with the following steps IDLE MODE ACTIVATION The vehicle must be running STEP 1 135 FA Ensure the transmission is in the NEUTRAL position SN Release the brake pedal Page 7 16 SIERS i Press the remote START button The parking lights will flash once 1 and then remain on STEP 6 gt Remove the key from the ignition barrel lt Q The vehicle will continue to run with the the Remote Starter STEP 7 Exit the vehicle and close all of the doors The vehicle will continue to run after all the doors are closed STEP 8 1 Remote stop the vehicle The engine will continue to run until either the remote stop function is pressed see USING THE RE MOTE CONTROL page 4 the Remote Starter runtime expires the parking brake is disengaged the brake is pressed or the hood is opened If the Remote Starter is shut down by transmitter it will automatically go in to Ready Mode if all the doors are closed A WARNING Never leave children or animals in a Remote Started vehicle unattended TURBO MODE AUTOMATIC TRA
12. in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with the Industry Canada Radio Standards Specification RSS 210 Its use Is authorized only on a no interference no protection basis in other words this device must not be used if it is determined that it causes harmful interferences to services authorized by IC In addition the user of this device must accept any radio interface that may be received even if this interference could affect the operation of the device Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Page 3 16 USING THE REMOTE CONTROL The remote starter is equipped with two 1 way 4 button multi channel remote control Locks all doors arm
13. larm sound The Alarm will remain active and will immediately resound if a zone Is re triggered e Press the UNLOCK button TWICE to stop the alarm sound deactivate the Alarm and unlock the doors e When the vehicle is unlocked the horn siren will sound with several short chirps to indicate the zone that has previously triggered the Alarm See Remote Start Alarm Diagnostics page 15 NOTE 1 If the vehicle is running with the Remote Starter and the Alarm is triggered the Remote Starter will shut down immediately This applies to Cold Start Turbo and Idle Modes However the vehicle can be Remote Started at a later time i e The Alarm will not cancel Cold Start Timer NOTE 2 When an alarm infraction has occurred the LED on the antenna will quickly flash 3 times followed of a long pause It will continue to flash until the alarm is disabled OPEN ZONE NOTIFICATION When the LOCK button is pressed to ARM the Alarm non Valet Mode it will indicate if there are Page 12 16 any zones which are currently active The Alarm will sound with several short chirps to indicate which zone is active A silent ARM or only 1 chirp indicates that no zones are currently active See Remote Starter Alarm Diagnostics page 15 FALSE ALARM DEACTIVATION This option will disable any zone that triggers the alarm 3 consecutive times The zone will automati cally re enable once the LOCK button or the UNLOCK button is pressed SHOCK SENSOR ZONE 4 The Alarm syste
14. lation Additionally the original installation centre may refuse all fees incurred by the latter service centre if any Page 14 16 REMOTE START ALARM DIAGNOSTICS REMOTE STARTER DIAGNOSTICS ALARM DIAGNOSTICS Parking Light flashes before starting Parking Light flashes after disarm 3x Ready mode disabled 3x Door open zone 3 Ax Valet mode activated The LED is on Ax Shock sensor zone 4 DX Hood open DX Hood open zone 5 Parking Light flashes after Shutdown 6x Trunk open zone 6 1x Normal stop Brake Park Brake 7x Auxilliary IN zone 7 3x Runtime expired or shut down by transmitter 8x Tilt Sensor zone 8 Ax No tachometer signal 9x Ignition zone 9 OX Hood open 6x Over crank threshold 8 seconds Page 15 16
15. lease the valet button 7 times X11 Press and hold the valet button once for 3 seconds to finish the sequence STEP 4 Valet mode enabled The LED is ON A Valet mode disabled The LED is OFF Note The coded valet option allows a selection of one of the five available codes Once the installer chooses one of the codes note the value here so you do not forget it VALET MODE VIA REMOTE Valet Mode disables the remote starter and alarm Whenever the vehicle is being serviced or repaired or the vehicle is parked indoors it is mandatory that Valet Mode be enabled to prevent an accidental Remote Start Note The alarm system is deactivated including Starter Kill when the system is in Valet Mode How ever you are still able to lock amp unlock the doors and release the rear hatch trunk This method of enabling disabling Valet Mode uses the remote transmitter instead of the valet switch indicated in the preceding section To enter Valet Mode using the remote transmitter proceed with the following steps STEP 1 Press and release the FUNCTION button within 12 seconds gt T T simultaneously press and hold the LOCK and UNLOCK buttons for 1 second Page 9 16 To exit Valet Mode using the remote transmitter proceed with the following steps STEP 1 Press and release the FUNCTION button within 12 seconds J gt a simultaneously press the LOCK and UNLOCK buttons for 1 second COLD START TIMER MODE Mode will remot
16. lly offered with most basic Remote Starter systems There are certain features listed in this manual that may not be available for your system There may also be features listed in this manual that require additional installation or programming before they are active In order to truly enjoy the benefits of this system we recommend that you thoroughly review the following manual This system contains transmitter s and a receiver with 900m 3000ft range Page 2 16 CAUTION WARNING IT IS THE RESPONSIBILITY OF THE REMOTE CAR STARTER OPERATOR TO e ensure that the vehicle is parked in a safe and responsible manner e ensure that the vehicle is not remotely started indoors garage underground park ing e ensure that the vehicle is not remotely started with a passenger inside e ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged on manual transmission in order to avoid accidents upon remote starting X when leaving the vehicle ensure that the gearshift lever is in the PARK position for an automatic transmission in order to avoid accidents upon remote starting Note Make sure that the vehicle cannot start in Drive position e ensure that the remote starter is disabled or put into valet mode before servicing When servicing the vehicle enable valet Mode via switch VALET CODING page 8 NOTE e The system can be configured in three different ways Remote Start only alarm onl
17. m supports FSS2Z 2 stage 3 wire Shock Sensors The Shock Sensor will produce a short audible warning on a weak shock and will trigger a full alarm on a strong shock Whenever the vehicle is running with the Remote Starter the shock sensor is ignored until the Remote Starter shuts down However the Alarm can be set to monitor the Shock Sensor if the vehicle is Armed AFTER the vehicle is Remote Started VEHICLE LOCATOR PANIC MODE To locate your vehicle in a busy parking lot press the LOCK button for 3 seconds to sound the horn siren If installed and flash the parking lights Press unlock to cancel this Mode Note If an Alarm pre triggered zone is in memory this Mode will NOT clear this zone from memory SENSOR DEACTIVATION In cases where a sensor is too sensitive and causes false alarms it is possible to disable some of the zones The Shock Sensor zone 4 Auxiliary In zone 7 and the Tilt Sensor zone 8 To disable all of these zones press the auxiliary FUNCTION button followed by either the LOCK button or the UNLOCK button Confirmation of 1 signal indicates the zones are activated and 2 signals indicates the zones are deactivated Page 13 16 TRANSMITTER RANGE Several factors may affect the operating range of the remote transmitter e A weak transmitter battery e The operating environment such as in the city and airports due to radio interference cell phone towers etc e Several types of metal such as the vehicle itself
18. rt signal START Approximately 5 seconds later the engine will crank Once the vehicle starts dd Ds the parking lights will turn on and remain on for the entire duration of the Remote Starter runtime or until the Remote Starter is shut down If the vehicle fails to start on the first attempt the Remote Starter will wait 3 seconds before it will attempt to start the vehicle again The Remote Starter will attempt to start the vehicle 2 times de fault before giving up See Failed Remote Start page 14 ACCESSORY PRESET Q Heater amp Heated Seat s When leaving the vehicle it is recommended that the driver pre set the climate controls in preparation for a later Remote Start When the vehicle Remote Starts the current or last setting for the climate controls windshield wipers and other accessories will be used When setting the blower motor fan speed and heated seats if equipped should not be left on HIGH It is recommended to leave these settings on either a LOW or MEDIUM setting Windshield Wipers amp Radio amp Headlights Some vehicles require the radio windshield wiper headlight circuits to become energized while running under Remote Start When leaving the vehicle you must ensure that the windshield wiper and headlight switches are turned off Leaving the headlights on with some vehicles could cause them to remain on even after the Remote Starter has shut down resulting in a dead battery Rear Defrost On most vehicle
19. s the Rear Defrost can only be activated after the vehicle has been started and in most cases this feature is not included with a Remote Starter installa tion On some vehicles it may be possible for the installer to hook this feature up so it either automatically enables after Remote Start or can be enabled by using an AUX output See Auxiliary use page 10 Driver Presets Some vehicles retain different seat mirror and radio settings for each dri ver Different driver presets are not controlled by the Remote Starter however they may be controlled with the Bypass Interface Kit READY MODE MANUAL TRANSMISSION ONLY Two activation methods are possible please consult the salesman or installer to determine which of these modes applies to your vehicle There are always safety concerns for a manual transmission vehicle to accidentally start while in gear Ready Mode alleviates these concerns The driver must enable Ready Mode in order to Remote Start the vehicle at a later time Once Ready Mode is set up the vehicle can be started stopped at will as many times as needed However once the parking brake is disengaged the hood is opened or any of the doors Page 5 16 are opened Ready Mode will deactivate and the vehicle will not start until Ready Mode Is reactivated METHOD 1 PROGRAMMED BY DEFAULT THIS METHOD WILL ACTIVATE THE REMOTE CAR STARTER SEQUENCE ONLY WHEN THE END USER IS USING THE REMOTE CAR STARTER REMOTE The vehicle must b
20. ssssecsecsscssessseuessesseeseeseeseesnssneeeeneeneessen 8 VALET MODE VIA SWITCH VALET CODING seas aaa 8 VALET CODING DISBALED DEFAULT cscssssssessessesseessesseesesssssseesssneessesssessesisseeseesssseseessereeseesnsenes 9 VALET CODING ENABLED OP ON taninos 9 VALET MODE MAREO queres to 9 CULO START TIMER MOD Eos ara 10 SUMAR UDE ciiai 10 REMOTE LOCKING AND UN DOCM isc ora nan innana nadaanan ii 11 AA 11 CONFIGURABLE FONCTIONALITY DURING INSTALLATION ccsccssessesssssessscssecssssecsecsecsesseessesucaneensaneenes 11 REMOTE DOOR ECOS correo 11 ACTIVE OR PASSIVE ARMING dresati en seS EEAS AE OE EE ETER S 11 IGNITION DOOR LOOK Sicario dama ena niendo aia tica 12 Sn tn E ee ee 12 TRUNKIHATCH RELEASE ZONE 6 nac 12 A 12 RUNTIME RE SE Parera ion cut eben iether 12 BLA scissile ctl ler aaa 12 AUDIBLE CONFIRMATION ercer nta aa 12 PA PNAC A 12 OREN ZONE NO INTO agraciada 12 FALSE ALARM DEACTIVATION corra dto apa 13 SHOCK SENSOR ZONE 4 oropani EENE E e EE ESE ES E nessa EEE ee 13 VEHICLE LOGATORIPANIC MODE sisrsssieitiaresriinirr atado EnS AEEA Ea EED 13 o E ES 13 TRANSMITTER BANDE csiis eaa 14 PILED REMOTE STAR Lama ceceuduasenseacasenndcneseeaannteieaaesce eee 14 REMOUTE STARE 7 ALARM DIAGNOS FIGS asin 15 INTRODUCTION Thank you for purchasing this Remote Starter Alarm system This is a state of the art Remote Starter Security System including numerous new comfort and security features and all of the elementary fea tures genera
21. the anti theft system and activates the Alarm if installed Press LOCK for 3 sec onds to activate the Panic Mode Unlocks all doors disarms the anti theft system and deactivates the Alarm if installed Remote start the vehicle Press START again to reset the runtime See remote starter features page 7 Opens the trunk and deactivates the Alarm if installed The Alarm ignores the trunk zone until it is closed Press and release FUNCTION and then Remote Stop press START Press and Qre lease AUXILIARY1 See Auxiliary use FUNCTION and then press LOCK Pape 10 Press and release AUXILIARY2 See Auxiliary use FUNCTON and then press UNLOCK page 10 LOCKED Until the THE RE RED DEL turn Press simultane MOTE de See REMOTE LOCKING AND LOCK UNLOCKING page 11 UNLOCKED Until the THE RE GREEN DEL MOTE turn on The remote flash DEL BLUE when a button is pressed The remote flash DEL GREEN when the remote is transmitting the informations For car command confirmation see ALARM ACTIVITY page 11 Page 4 16 REMOTE STARTING REMOTE STARTING THE VEHICLE This Remote Starter supports both manual and automatic transmission vehicles For manual transmis sion vehicles see the Ready Mode section REMOTE STARTING ee To remote start the vehicle press the START button for approximately C 3 second Slee q on The parking lights will turn on to indicate a response to the Remote Sta
22. tton LOCK button Aux 2 Passenger side sliding door if installed DD Press and relase the FUNCTION button the remote LED flashes slowly white gt within 12 seconds press the UNLOCK button 1 oococssonsosssssss ns oonoosopooooospossps opSops ssS sS sSsS sS ssssssssss ssssssassssssss sasosn sc ss sos s lt sons s cs popnopooo oonoons osppnposspoonoons oos pooooos n op np oons aspoXooo Note The function of the auxiliary outputs may vary depending on the vehicle and the installation In most cases these outputs are not used and in some cases they may be used to control other features such as the power windows sunroof or heated seats Check with the installer to find out what AUX outputs have been installed and what they control Page 10 16 REMOTE LOCKING AND UNLOCKING LOCK THE REMOTE UNLOCK THE REMOTE To enable the but tons on the remote simultaneously press u and hold the To disable all the buttons on the remote simultaneously press and hold the amp LOCK and FUNC TION buttons until the RED LED UNE comes on The RED LED will come TION buttons nnti on Whenever a button is pressed the GREEN LED when the remote is LOCKED comes on REMOTE STARTING OPTIONS CONFIGURABLE FONCTIONALITY DURING INSTALLATION This Remote Starter is designed to be highly flexible when integrating into original equipment OEM With the following programmable options the Remote
23. urrent needed to start the vehicle in extreme temperatures e Low Fuel or water in the fuel tank Keep your fuel tank full as much as possible to prevent the build up of condensation in the tank e A corroded or broken Hood Pin switch Visually inspect the hood pin switch frequently Cover with a dialectic grease to prevent corrosion e Trailer wiring Corroded or improperly wired trailer wiring may cause the park light signal to bleed into the brake signal This will cause the Remote Starter to shut down as soon as the park lights are turned on e Problems with the Bypass Kit if installed If you are able to put the Remote Starter into Ready Mode Idle Mode or Turbo Mode but you are unable to Remote Start the vehicle then the Bypass Kit may be failing Several Remote Start attempts with a failed Bypass Kit may lock your vehicle for several hours e Dash warning lights The dash should display in exactly the same way when either starting the vehicle with the key or with the Remote Starter If the dash displays any warning lights Check Engine ABS or Theft once Remote Started then something is wrong Stop using the Remote Starter and have it looked at immediately TIP If your vehicle is experiencing any problems either starting or running with the key have it looked at by the Remote Starter s installer first Having the vehicle worked on by another service centre may void any warranty and or guarantees on the Remote Starter and its Instal
24. y or alarm and remote starter e The options vary by vehicle the components can be added to the system and the functions on the vehicle INDUSTRY CANADA USER NOTICE Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment GOVERNMENT REGULATIONS This device complies with part 15 of the FCC Rules Operation is subject to the following two condi tions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used
Download Pdf Manuals
Related Search