Home

User Guide - Autostart

1. START Press AUX gt AUX gt START STOP STOP Press AUX gt AUX gt TRUNK TRUNK Note If the multi level features have been modified from their default state by your installer the AUX button may have to be pressed once twice or three times according to the option you chose OEM Style Alarm The OEM style alarm if configured by your installer monitors the doors hood and ignition switch of your vehicle It will sound the horn if a door or the hood is opened or if the key is turned into the IGNITION ON position e Toarm the OEM style alarm press the button on the transmitter The OEM style alarm will ONLY arm if the button on the transmitter is pressed The LED on the antenna will flash slowly to indicate that the OEM style alarm is now armed e To disarm the OEM style alarm press the k button on the transmitter To stop the horn from sounding if the OEM style alarm is triggered press the or button or put the system in and out of Valet Mode See page 8 Intrusion Codes via horn The system monitors the following e Doors e Hood e Ignition Note If an intrusion has occurred the HORN will sound for a maximum of 1 minute EN If an intrusion has occurred and S amp H pressed the horn provides an intrusion code corresponding to the type of intrus
2. must be professionally installed For more information see your nearest authorised Directed Canada dealer With many advanced functions this product will satisfy any one of your expectations from high end commodity and security systems without neglecting any standard feature commonly offered by entry level starters 1 Certain conditions apply See your authorised Directed Canada dealer User Guide P 3 Using the Remote Control Your remote starter is equipped with a 5 button multi channel remote control It can operate two independent vehicles equipped with a remote starter see Multi car operation section on page 14 The functions of the transmitter are as follows 2 way LED remote icon may vary P 4 LOCK Locks the doors and arms the STARTER KILL if installed UNLOCK Unlocks the doors and disarms the STARTER KILL if installed Activates the AUX 1 output if Priority Door Access is configured TRUNK Opens the TRUNK or activates the AUX 3 output Note Trunk option must be installed START STOP Remote starts or stops the engine Gets the system into Cold Weather mode by pressing the SHIFT button and then pressing and holding the START STOP button for 3 seconds Note Icon may vary AUX This button serves as a second function button This button allows assigning different functions to any of the other four buttons User Guide 1 way companion remote where available g LOCK Locks the
3. this feature will remotely set the vehicle to a no remote start mode if the vehicle is parked indoors there is no danger of it starting accidentally by remote control If the vehicle has a manual transmission it should be set into ready mode before activating the Home Valet Note Once the Home Valet Mode is activated the vehicle will not start by remote but the OEM alarm functions will remain active To take the system into home valet mode 1 Press the or kw button 2 Within 3 seconds press the and D buttons simultaneously until the remote beeps twice To take the system out of home valet mode e Turn the ignition key to the IGNITION ON RUN position The system will warn you if someone attempts to start your vehicle while it stands in home valet mode The parking lights will e Turn ON then OFF then Flash twice pause then Flash twice again AUX 1 Note This 500 mA negative Aux 1 output can be used for many different applications Priority door This great feature allows the user to unlock solely the driver s door with a single press of the button on the transmitter and to unlock the other doors if desired by pressing the K button for a second time The output will provide a 1 second negative output when the k button is pressed a second time on the transmitter Horn Confirmation AUX 1 can be programmed to trigger the horn every time the button is pressed or when the button is pressed twice within 3
4. doors and arms the STARTER KILL if installed UNLOCK Unlocks the doors and disarms the STARTER KILL if installed Activates the AUX 1 output if Priority Door Access is configured TRUNK Opens the TRUNK or activates the AUX 3 output Note Trunk option must be installed START STOP Remote starts or stops the engine Gets the system into Cold Weather mode by pressing the SHIFT button and then pressing and holding the START STOP button for 3 seconds Note Icon may vary AUX This button serves as a second function button icon may This button allows assigning different functions to any vary of the other four buttons Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start Settings for the blower motor fan front and rear should not be left on HIGH It is recommended to leave the settings on LOW or MEDIUM instead Windshield Wipers amp Radio amp Headlights Certain vehicles require the radio and or windshield wiper and or headlight circuits to become energized while running under remote start When leaving the vehicle you must ensure that the windshield wiper and headlight switches are OFF Leaving the headlight switch ON on certain types of vehicles could cause them to remain ON even after remote starter shut down resulting in a dead battery Arming and disarming the starter kill if installed This added security featur
5. seconds When horn confirmation is activated panic mode is enabled If horn confirmation is disabled panic mode will not be available User Guide P 13 AUX 2 If configured at installation this feature can be activated by pressing the AUX or Shift button followed by pressing and holding the lit up button to activate AUX 2 Horn Timing Adjustment The pulse duration can be configured by your installer from 5 ms to 200 ms Multi car Operation This option allows the owner of two vehicles both equipped with the same Remote Car Starter model to control both systems with a single remote control To control the second vehicle Press TRUNK LOCK buttons simultaneously LOCK Press TRUNK UNLOCK simultaneously UNLOCK Press TRUNK START STOP simultaneously START Press TRUNK START STOP simultaneously STOP Press AUX gt AUX gt TRUNK TRUNK OR Press AUX gt AUX gt LOCK LOCK Press AUX gt AUX gt UNLOCK UNLOCK Press AUX gt AUX gt START STOP
6. void the user s authority to operate the equipment 2014 07 11 Canada Table of Contents Government regulation Sasarina a 3 Introduction with SmartStart d DEE 3 Using the Remote nee 4 Vehicle PROS GUS zetbet ngg e EEN 5 WEEN 5 Windshield Wipers amp Radio amp Headhahts 5 Arming and disarming the starter kill if installed i eseeeseeeseeeeeseeeeeeeenseeenees 5 Remote Starting Your Vehicle cssssssscscsssseescessseseeecsessssescesseseseseeareeseensasanseseeneanansesees 6 Setting Your Vehicle into Ready Mode csssescssessessssssssssssssssesessessssseseesssssesersesaees 6 Remote Stanin a Lansmeeatacuee cement aden tatuns T Bing O EE T Remote Starter Keakute zeuaregeaeseeges eeeuaesee ee 8 ROMO DOOL Bee 8 REMOTE Helle ET 8 FSH VOCE EE 8 EE Oe 8 Pane 0 EE EE EE 9 TI ae TEE 10 Eo EE Oe Ta 10 ESC CATH Ri TEE 10 Disable Enable Etage eege 11 RS OV STATION e a ashe as waa ste cal ete a 11 Feature Confirmation ei EI EE 11 Advanced Features Installation programmable Options ccssesssssseeeeeeseeeeees 11 lIgnition controlled Door MOCKS EE 12 EE etlecher 12 SLC Ol EE 12 ICING RUM lr EE 12 BR leie H eet 12 Home Valet M MOUS order 13 AUX EE 13 lee eege kee 14 Homm mmng Tel un EE 14 Klee eege 14 BIS Oe EE 14 Igel BT a NOMI EEN 14 Vehicle Status ROGUES E sisicdiseinsicatestieaceseinanccavaiaesdtsatnddeaeetntatanatntateunadsddnnineatansinantananedeeaeenaals 15 Status Request W
7. LED on the antenna will stay ON indicating that the vehicle has successfully entered Valet mode Using the TRANSMITTER Remote Valet Mode 1 Press and hold the wl and D buttons simultaneously until the remote beeps once pauses then beeps once again Release the buttons 2 The and buttons will flash 3 times A The LED on the antenna will stay ON indicating that the vehicle has successfully entered Valet mode To take the system out of Valet Mode Using the KEY Ignition Valet Mode 1 Insert the ignition key into the ignition switch Within 10 sec cycle the ignition key to the IGNITION RUN and OFF positions 5 times until the parking lights flash twice 2 Turn the ignition OFF A The LED on the antenna will flash rapidly indicating that the vehicle is now out of Valet mode Using the TRANSMITTER Remote Valet Mode 1 Press and hold the and LZ buttons simultaneously until the remote beeps once pauses then beeps once again Release the buttons 2 The and L I button will flash 3 times 3 The LED on the antenna will flash rapidly indicating that the vehicle is now out of Valet mode If someone has attempted to remote start the vehicle while in Valet Mode the parking lights will turn ON then OFF then flash twice Panic Mode Note Panic mode can only be activated if the horn has been adequately configured by the installer In an emergency situation you can activate panic mode by pressing and holding the AUX
8. TWO WAY FM LED AUTOMATIC MANUAL TRANSMISSION REMOTE STARTER START User Guide WARNING It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible manner 1 a Manual transmission When leaving the vehicle it is the user s responsibility to ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged in order to avoid accidents upon remote starting b Automatic transmission When leaving the vehicle it is the user s responsibility to ensure that the gearshift lever is in Park in order to avoid accidents upon remote starting Note Make sure that the automatic vehicle cannot start in Drive It is the user s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing DIRECTED INDUSTRY CANADA USER NOTICE Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could
9. as installed with the Remote Door Locks option you will have the convenience of remote keyless entry To LOCK your doors and ARM the system 1 Press and hold the button for approx 1 sec 2 The remote will beep once to confirm locking of the doors To UNLOCK your doors and DISARM the system 1 Press and hold the SM button for approx 1 sec 2 The remote will beep twice to confirm unlocking of the doors Remote Trunk Release If your system was installed with the Remote Trunk Release option you can open your trunk by pressing the button until the remote beeps once In addition this will also disarm the OEM style alarm if installed Idle Mode Convenience feature Idle Mode allows you to keep the engine running and the doors locked while you stop for example at a convenience store or for a short delivery This feature allows you to let the remote starter take over control of the vehicle i e no Key in the Ignition Switch while the engine is running Activating Idle mode Automatic transmission 1 With the engine running make sure to release the brake pedal and press the Kg T or H button on the transmitter until the parking lights come ON Note SmartStart can be setup to use the SmartStart icon to activate Idle mode 2 Remove the ignition key from the ignition switch The engine will continue running Exit the vehicle All doors the hood and trunk should be closed Press the button to lock the doors to arm
10. button until the horn starts honking If the vehicle is under a remote start the engine will shutdown automatically before setting off the horn You can stop the horn by pressing d this will lock your doors and deactivate panic mode or this will unlock your doors and deactivate panic mode Furthermore the panic mode can be stopped by activating Valet Mode page 8 Panic Mode will automatically shut down after 30 sec User Guide P 9 Quick Lockout Also called Secure Panic For fast protection in emergency situations the system will LOCK all doors when you press the brake pedal while you hear the Horn sounding Quick Lockout is only available when Panic mode has been triggered Cold Weather Mode If the vehicle has a manual transmission Ready mode page 6 should be set before entering Cold Weather Mode When Cold Weather Mode is active the engine starts every 2 hours and runs for 3 minutes or for 8 or 20 minutes with diesel engines Cold Weather Mode automatically ends after 24 hours or 12 starts To enter Cold Weather Mode 2 way remote 1 Press and release the AUX button 2 The button on the transmitter will light up 3 While the button is still lit press and hold the D button until the remote beeps once pause then beeps twice 4 Release the H button Its LED will flash quickly To enter Cold Weather Mode 1 way remote 1 Rapidly press AUX twice The remote s LED will start flashing 2 P
11. curity system is disarmed for a remote start Secure Lock will relock your doors as soon as the vehicle is started Once the engine is shut down by remote or after its runtime has expired Secure Lock will also rearm your factory security system and relock the doors Safe Start This feature will eliminate accidental remote starts e g when children are playing with the transmitter Safe start enabled If this feature is enabled the user must press the D button twice within 3 seconds to remote start the vehicle Swap start 2 way remote If this feature is enabled 1 Press and release the AUX button 2 The button on the transmitter will light up A While it is lit press to remote start the car The AUX 2 output can be activated by pressing the H button Swap start 1 way remote If this feature is enabled 1 Rapidly press AUX twice The remote s LED will start flashing 2 While the LED is flashing press to remote start the car The AUX 2 output can be activated by pressing the D button Engine Run Time If you have a gas engine your Remote Car Starter can be programmed to run the engine for 3 15 or 25 minutes 15 minutes by default If you have a diesel engine the Remote Car Starter can be programmed to run the engine for 8 20 or 30 minutes 20 minutes default Turbo Mode If Turbo Mode is configured at installation it will allow a turbocharger to idle down after the user leaves the vehicle the unit will take over t
12. d to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with the Industry Canada Radio Standards Specification RSS 210 Its use is authorized only on a no interference no protection basis in other words this device must not be used if it is determined that it causes harmful interferences to services authorized by IC In addition the user of this device must accept any radio interface that may be received even if this interference could affect the operation of the device Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Introduction with SmartStart D This is a state of the art remote car starter system The system is packed with advanced features such as priority access to the driver s door commodity features the Safe Start children safety feature and SmartStart SmartStart is a groundbreaking technology that enables your remote starter features to be accessed by your smartphone Features include keyless entry trunk release panic remote start stop toggle and alarm notifications Note SmartStart
13. e will prevent the vehicle from starting with the Ignition key when the starter kill is armed If the system was installed with the starter kill option the vehicle will not be able to start with the key unless the system has been unlocked first or put into Valet Mode page 8 Note If the Starter Kill is installed the vehicle will benefit from a protection against starter motor damage that could occur after remote starting the engine should the user by force of habit turn the ignition key to the CRANK position The Starter Kill if installed can be configured by the installer either to Passive Mode so as to arm automatically or Active Mode so as to require the user s intervention for arming By default the Remote Car Starter is configured to Passive Mode User Guide P 5 Passive mode To arm the Starter Kill e Press the 3 button on the transmitter OR e Lei the Starter Kill arm automatically 1 minute by default or 3 minutes if configured this way after the ignition is turned OFF or once the last door is closed if the doors are monitored The parking lights will flash once e The LED on the antenna will flash quickly during the countdown preceding the activation of the Starter Kill e Once the activation countdown expires the LED will send a series of quick double flashes to indicate that the Starter Kill is now armed To disarm the Starter Kill e Press the E button on the transmitter e The Starter Kill wil
14. en running for 2 minutes already pressing the j button will reset the counter to zero and allow the engine to run for another cycle in this case 3 minutes P 10 User Guide Disable Enable LED flashing To disable the LED Press and E simultaneously until the remote beeps once pauses for 2 seconds then beeps once again Release the buttons The parking lights will flash 3 times To Enable the LED Press and E simultaneously until the remote beeps once pauses for 2 seconds then beeps once more Release the buttons The parking lights flash once Constant output Pressing and holding the button for more than 3 seconds will lock all doors and will send a constant pulse as long as the button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling up the windows Please refer to your installer to see if your vehicle is compatible with this option Pressing and holding the W button for more than 3 seconds will unlock all doors and will send a constant pulse as long as the button is held down maximum of 15 seconds This constant pulse can be configured to activate certain functionalities such as rolling down the windows Please refer to your installer to see if your vehicle is compatible with this option Feature Confirmation Chart Feature LOCK UNLOCK TRUNK START STOP Geen Ma eee Lock 3 flashes nese sees EC OT o age ores stones
15. he vehicle and keep it running for 60 seconds or until it is shut down by remote control then shut down the engine If your vehicle has an automatic transmission proceed as follows to set the system to Turbo Mode 1 With the engine running make sure to release the brake pedal and press the k kd or H button on the transmitter until the parking lights come ON Note SmartStart can be setup to use the SmartStart icon to activate Turbo mode 2 Remove the ignition key from the ignition switch The engine will continue running 3 Exit the vehicle and close all doors hood and trunk P 12 User Guide 4 Press the a button this will lock the doors arm the OEM style alarm if configured and confirm that the vehicle is in Turbo Mode 5 The engine will shut down after 60 seconds If your vehicle has a manual transmission follow all steps of the Ready Mode routine page 6 to activate Turbo Mode At the last step press either e to lock the doors and have the engine shut down after 60 seconds The parking lights will flash 3 times and remain lit The OEM style alarm and starter kill if configured will be armed e ito unlock the doors and have the engine shut down after 60 seconds The parking lights will flash 3 times and remain lit H to shut down the engine without affecting the doors Note The vehicle will enter Ready Mode once the engine run time expires Home Valet Mode If configured at installation
16. hen the Engine IS NOT RUNNING cccccccsecseecsssscssetecseseeesssteeesseeees 15 Status Request When the Engine is Running s s snnsnsnsinnnsnsnsinnnsnsininnrsnsnninnrsrnrninnrsrnnns 16 Ready Mode Status EE 16 Troubleshooting Poor Transmitting Range s sssssssssssssnsnnununnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnan 17 Diagnostics Parking Light Flash Table ssscssssssssscssssesssseeessseessssesessssesassesesansncas 17 P 2 User Guide Government regulations This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encourage
17. ion that occurred 1x power interruption 6x Ignition P 14 User Guide Vehicle Status Request The status request feature allows the user to see the status of the vehicle e if the doors are locked or unlocked or if the vehicle is in cold weather mode home valet mode in valet mode or how much time is left in the run time cycle The following charts Tables 1 2 and 3 indicate the confirmation sequences To retrieve the vehicle status Press and release the AUX button then press and release the button there will be a beep The transmitter will then flash the corresponding sequence of LED s depending on the vehicle s status If the engine is NOT running e If the vehicle is in or out of ready mode If the engine IS running under a remote start if the doors are locked or if the doors are unlocked The status request feature is a two step procedure e The first sequence of flashes denotes if the vehicle s doors are locked or unlocked e The second sequence of flashes if applicable denotes if the vehicle is Cold Weather mode Home valet mode or Valet mode e f there is no second sequence transmission then the vehicle is none of the 3 mentioned features Cold weather mode Home valet mode or Valet mode Status Request When the Engine IS NOT Runnin sol eem Cl ege 3 flashes 1st sequence Cold 1st sequence Weather q 3 flashes if unlocked seen nn 1st sequence ame 1st sequence 2
18. l automatically rearm itself after 1 minute by default or 3 minutes if configured this way if no door is left opened if the doors are monitored and the ignition is not turned ON Active Mode To arm the Starter Kill e Press the o button on the transmitter e The parking lights will flash once e The LED on the antenna will flash slowly e f remote door locks are installed this will also lock the doors and arm the OEM style alarm if configured To disarm the Starter Kill e Press the E button on the transmitter e The parking lights will flash twice e The LED on the antenna will remain OFF e f remote door locks are installed this will also unlock the doors and disarm the OEM style alarm if configured Remote Starting Your Vehicle Setting Your Vehicle into Ready Mode If your vehicle has a manual transmission you must read the following indications In order to start the vehicle by remote the unit must first be set to Ready Mode If the unit is not set to Ready Mode it cannot remote start the vehicle Please note that Ready Mode can be enabled by the remote or the handbrake depending on the option that was selected by your installer Therefore you must follow the appropriate procedure between the two described below in order to set your vehicle into Ready Mode Once the system is set to Ready Mode the vehicle can be remote started and stopped at any time The system will exit Ready Mode if a door the hood or
19. oof and A pillars brings about considerable radio frequency deflection in this case the signal from the remote control As a result the direction in which the vehicle is facing in relation to the remote control can affect the range Straight on standing in front of the vehicle generally gives you the greatest range the second best performance is from the back Using the remote control from either side of the vehicle will usually give the lowest range The range will be significantly lower in a crowded parking lot than in open space Always hold the transmitter high approximately at shoulder height Holding the transmitter against your chin will also increase your range your head acts as an antenna The operating range will be somewhat lower on vehicles equipped with an aftermarket or factory alarm Diagnostics Parking Light Flash Table Parking lights flashes 3 Doors locked Trunk released Start signal received from the remote Runtime has expired Doors unlocked Valet mode is deactivated 2slow Shutdown by remote o K o slow K K 1 slow gt 2 fast Valet mode activated EE A remote start was attempted while the brake pedal is engaged wt IL Ron sivtnas amped vie heoad igen A remote start was attempted while the hood is open ONDtwice ON 3 3times ON gt 3 times __ SolidON e _ Engine is running under remote star User Guide P 17
20. ress and hold H until the parking lights will flash for 2 seconds pause and then flash 3 times To exit Cold Weather Mode do any one of the following actions e Open the hood e Start the engine remotely e Turn the ignition key to the IGNITION ON RUN position e Press and release the AUX button a The button on the transmitter will light up b While the button is still lit press and hold the D button until the remote beeps once pause then beeps once again c Release the j button Its LED will flash quickly e away remote Rapidly press AUX twice The re mote s LED will start flashing Press and hold D until the parking lights flash for 2 seconds pause and then flash twice To verify whether the system is in Cold Weather Mode e Automatic transmissions only Press the brake pedal If the vehicle is in Cold Weather mode the parking lights will remain ON while the brake pedal is pressed e Do the vehicle status request feature page 15 Extended Run Time While the vehicle is running under a remote start press and hold the U button until the remote beeps This will reset the run time counter to zero and restart the run time cycle from the beginning Note The extended run time procedure can only be carried out once per remote start To stop the vehicle at any moment simply press and release the D button Example If your remote car starter is programmed for a run time of 3 minutes and your vehicle has be
21. risequence tsecond 1st sequence 1t sequence Desequence 1second _t secon User Guide P 15 Status Request When the Engine is Runnin When the vehicle doors are locked The LED 1 will flash 3 times to denote that the vehicle s doors are locked When the vehicle doors are unlocked The LED 2 will flash 3 times to denote that the vehicle s doors are unlocked And RUN TIME LED 1 LED 2 LED 3 LED 4 I there Is more than 3 4 of 3 ON for 1 sec ON for 1 sec ON for 1 sec ON for 1 sec Run time cycle If there is more than half of 3 ON for 1 sec ON for 1 sec ON for 1 sec run time cycle If there is more than 1 4 of run time cycle If there is less than 1 4 of 3 ON for 1 sec run time cycle Ready Mode Status Request STATUS SEQUENCE LED 1 LED 2 LED 3 LED 4 Beep s InReady iflocked 3flashes 1 Mode if unlocked Sass 3 flashes ix OoOO 7 1st sequence el 1st sequence 2nd sequence P 16 User Guide Troubleshooting Poor Transmitting Range Many factors may affect the operating range of the transmitter Some of these are The condition of the battery in the transmitter The operating environment for example downtown radio frequency noise airports cellular phone towers Metal any type of metal will affect operating range This includes the metal in the car The shape of the vehicle can affect range as well vans in general have an especially poor range The shape of the r
22. se tes Li Seng Toe s Toe Ee masie EHNEN ae SS 3 flashes Advanced Features Installation programmable Options The remote car starter was designed with flexibility and OEM integration in mind With its program mable options this unit can single handedly control nearly any electrical system in your vehicle Caution The programming of your system should be left to a professional Changing any one of the settings may affect the operation of your Remote Car Starter Exit Valet Mode ec 3 flashes Fail Start Attempt User Guide P 11 Ignition controlled Door Locks This is an added security feature If your Remote Car Starter was installed with the Ignition Controlled Door Locks option the doors will automatically lock as soon as the ignition key is turned to the IGNITION ON RUN position while the brakes are pressed The remote car starter will also lock any door that was unlocked and opened then closed the next time the brake pedal is pressed only when doors are monitored When the key is turned to the OFF position the doors will automatically be unlocked Secure Lock Disabled by default Before your vehicle can be remote started the factory security system must first be disarmed The Secure Lock feature may be required on certain vehicle models with factory security systems that automatically unlock the doors when the security system is disarmed To keep your vehicle protected when the factory se
23. t OPTION 1 No lock to shut down the engine without affecting the doors WARNING The vehicle is not WARNING Engine runs until the pre WARNING Do_not leave your armed or locked down programmed run time expires keys in the vehicle 7 The Parking lights will flash twice to indicate Ready mode is set Remote starting 1 Press the U button for approximately 1 second and release 2 The remote will beep once A The remote will confirm the remote starter s activation by beeping 3 times If your vehicle does not start at the first attempt the system will shut down wait a few seconds and try to start the engine again There will be 3 start attempts before the system gives up Driving Off With the vehicle running remotely press the button to disarm the starter kill if installed and unlock the doors Enter the vehicle and do the following 1 Turn the ignition key to the IGNITION ON RUN position Do not turn the key to the CRANK position while the engine is running This would cause the starter motor to re engage 2 Press the brake pedal to disengage the remote starter unit You are now ready to drive off Note On some Push To Start PTS vehicles no takeover is possible as pressing the brakes will shut the engine down Please talk to your technician to determine if the Takeover mode can be set for your vehicle User Guide P 7 Remote Starter Features Remote Door Locks If your Remote Car Starter w
24. the starter kill and to arm the alarm if available The engine will continue running a When re entering the vehicle the user must reinsert the key into the ignition and turn it to the ON position not Crank without pressing on the brake b Once the key is in the ON position press on the brake pedal to put the transmission in gear Pressing the brake pedal at this step will cancel the remote Starter takeover c Drive off If your vehicle has a manual transmission Idle Mode can be activated through the same routine as that used for Ready Mode page 6 at the last step press the button to lock the doors arm the system and leave the engine running Valet Mode When the vehicle is in Valet Mode the remote starter and alarm functionalities are disabled If the vehicle needs to be serviced or if you park it indoors Valet Mode will prevent the engine from being remote started accidentally P 8 User Guide Any of the following features will put the remote car starter into Valet Mode Ignition Valet This feature allows you to set Valet Mode using the ignition key Remote valet This feature allows you to set Valet Mode using the transmitter To put the system into Valet Mode Using the KEY Ignition Valet Mode 1 Insert the ignition key into the ignition switch Within 10 sec cycle the ignition key to the IGNITION RUN and OFF positions 5 times until the parking lights flash 3 times 2 Turn the ignition OFF 3 The
25. the trunk is opened if the brake pedal is pressed if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON RUN position P 6 User Guide To set the system to Ready Mode If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake 1 Ensure that all the doors hood and trunk are closed Make sure that the gear selector is in the neutral position 2 With the engine running apply the parking brake 2 With the engine running apply the parking brake once and release the brake pedal twice within 10 sec 3 Within 20 sec of engaging the parking brake 3 Make sure to release the brake pedal press and hold or ap ihe The parking lights will flash 3 times quickly and transmitter SmartStart uses only SmartStart icon The parking lights will flash 3 times quickly and remain lit Release the button 4 Remove the key the engine will keep on running 5 Exit the vehicle All doors should be closed including the hood and trunk 6 THERE ARE THREE POSSIBLE OPTIONS TO COMPLETE READY MODE programmable by installer OPTION 2 Manual shut down OPTION 3 Automatic shut default down The engine stops The engine keeps going until you The engine runs for 8 sec then press either locks the doors before finally shutting down the engine without a to lock the doors and shut user interaction down the engine b wl to unlock the doors and shut down the engine the remain li

User Guide - Autostart

Contents

Download Pdf Manuals

Related Search

Related Contents