Xyron 850 / 1200 user manual
Contents
1. Continue to turn handle until film is aligned and wrinkle free Install feed tray and trim off excess film using cut blade Remove used supply cartridge by pulling outward If there is film between the rollers turn handle counter clockwise To Install Part used Cartridges Attach reusable cartridge starter tool to partially used supply cartridge Insert partially used supply cartridge into dispenser Note tool should be positioned between rubber rollers in dispenser Turn handle clockwise until tool has exited dispenser and film is aligned and wrinkle free Store reusable cartridge starter tool for later use Install feed tray and trim off excess film using cut blade Supplies available for XYRON 850 XYRON 1200 Laminating Cartridges DL and SL Series Laminating Cartridges DL Series Xyron Technical Hotline 1 800 793 3523 USA DL201 100 Two Sided Lamination General use Gloss Finish DL1101 100 Two Sided Lamination L201 100 One Sided Lamination General use Gloss Finish General use Gloss Finish DL601 200 2 x Two Sided Lamination General use 4 inch 106mm 111015109 rie ar e AA SL601 200 4 w One Sided Lamination General Use Gloss Finish 45 7594 5866 Europe Adhesive Application Cartridges AT Series Adhesive Application Cartridges AT Series Adhesive Application Permanent High Tack AT1101 50 Adhesive Application ee Permanent High Tack A2. Xyron Adhesive Application amp Laminating System User s Guide XYRON 8 5 0 XYRON 1200 The Xyron 850 Xyron 1200 is designed to be used with one of Important Notice the following replacement cartridges Your Xyron 850 Xyron 1200 system is designed to permanently SL DL Double and single sided lamination attach a clear film or adhesive to the front and or back of any LAT Front lamination with adhesive transfer on the reverse substrate that is run through the machine The lamination film and AT Single sided adhesive transfer adhesive are not designed to be removed without substantial damage to the laminated substrate This process is NOT Please follow the attached directions carefully i recommended for any precious or single source documents GB Parts and Functions Document Feed Paddle Helps ensure wrinkle free output by providing slight back tension on document Replaceable Supply Cartridge Holds various lengths and combinations of film and Document Feed Tray Used to guide document into dispenser Leading edge of document slides in between tray and paddle during insertion Align to right for A3 A4 documents to the left for letter documents Setting Up Document Output Location where document exits dispenser when handle is rotated clockwise Handle Used to advance cartridge supplies when rotated clockwise Also feeds document through dispenser Roller Springs Prov
3. dhesive Application Permanent Low Tack Y o N one AT1105 50 Adhesive Application Ea X R Adhesive Application Permanent Acid Free Permanent Acid Free Xyron Inc Adhesive Application 15820 North 84th Street AT601 100 2 x Adhesive Application Permanent High Tack Non Permanent Repositionable 4 inch 106mm Scottsdale AZ 85260 USA Combination One Side Lamination Combination One Side Lamination 1 800 793 3523 One Side Adhesive Application LAT Series One Side Adhesive Application LAT Series FAX 480 443 0118 LAT201 50 1 Side Laminate 1 Side Adhesive Application LAT1101 50 General Use Laminate Permanent High Tack Adhesive 1 Side Laminate 1 Side Adhesive Application WWw xyron com General Use Laminate Permanent High LAT202 50 1 Side Laminate 1 Side Adhesive Application Tack Adhesive General Use Laminate Permanent Low Tack Adhesive LAT1106 50 LAT206 50 1 Side Laminate 1 Side Adhesive Application 1 Side Laminate 1 Side Adhesive Application General Use Laminate Non permanent Repositionable Adhesive General Use Laminate Non Permanent Repositionable Adhesive x XY R O N Combination One Side Lamination Combination One Side Lamination Xyron Inc USA One Side Magnet LM Series One Side Magnet LM Series Adhesive Application Non Permanent Repositionable AT1106 50 Xyron Europe A S LM201 12 1 Side Laminate 1 Side Magnet LM1101 10 1 Side Laminate 1 Side Magnet Xyron Asia Gene
4. ide spring force on rollers Remove springs to remove rollers and cut blade Cut Blade Slides to the left and right to cut output material after it exits dispenser Also can be used to trim excess material from leading edge of document Remove the Xyron System and Document Feed Tray from the packaging The System is shipped with a sample supply cartridge already installed Install the feed tray by inserting it horizontally into the cartridge opening by the grooves in the left and right dispenser side plates as shown below When correctly installed the tray will rest horizontally Document i Cartridge Feed Tray reference Assembly Upper groove in dispenser side plates Lower groove in dispenser side plates Basic operation Step 1 Insert and align document on feed tray Extend the document completely into the cartridge opening Align to the left for letter size documents to the right for A3 A4 documents Step 2 Gently guide the document forward while turning the handle clockwise Step 3 Trim to desired length using the cut blade at the roller exit Apply pressure down on the orange blade holder and slide to the left or right Cartridge Replacement Remove feed tray by lifting upward and gently pulling away from dispenser To Install New Cartridges Position cartridge leader between the rubber rollers in dispenser Turn handle clockwise to advance film Insert new supply cartridge
5. ral Use Laminate Magnet Backing General Use Laminate Magnet Backing 2001 Xyron Inc
Download Pdf Manuals
Related Search