FVE skylight user manual
Contents
1. 2 Mount the upper part of the holder 3 Place ZRC US controller on the holder 12 08 14 4 13 2012 FAKRO 4 QUICK START UP Operation of single skylight with ZRC US remote control ZRC US remote control is factory set to operate just one FVE skylight and one internal blind Both are operated using channel 1 of the remote To open close the skylight make sure channel 1 is selected To check the channel selection press control unit preselection button First red diode on the left should light on If any other diode lights on keep pressing preselection button unitl the first diode on left will light on To open or close the skylight point the remote control towards the skylight and press the A button to open and V button to close the skylight first pair of the buttons on the remote control The buttons in row two and three operate internal and external accessories respectively If the skylight does not react to the comments sent by remote from channel 1 the mosquito screen is placed properly and the skylights is connected to the power source please check other channels By pressing the SELECT button change the channel to no 2 and press skylight open button If the skylight does not work on channel 2 repeat the step for channels 3 and 4 If the skyligth still does not react the remote needs to be reprogrammed To reprogram the remote please go to chapter2. you have to set up for the new skylight s an individual address es Important Below programming procedure refers also to the situation when old remote control or a new one needs to be programmed to operate the FVE skylight on channel 1 To set the address of each skylight s you need to does not refer to FVE skylight you use the ZRC US remote control from No programming required here as the remote is factory programmed to work with that skylight on channel 1 1 Switch off the power supply of the skylight s 2 Remove the mosquito screen s and cover s at the bottom of the new skylight s 3 Set the proper combination of the bits panel SW1 on circuit board on each skylight s individually Below pictures show required configuration of bits on each of the FVE skylight s to individually operate with one remote control unit All of the FVE skylights have factory settings as presented in Skylight 1 Settings of Skylight 1 remains unchanged presented here for reference purposes only The bits panel SW1 is located in the left part of the circuit board of the skylight see point 6 Circuit board wiring diagram Skylight 1 Skylight 2 Skylight 3 Skylight 4 12 08 14 7 13 2012 FAKRO Bits configuration Skylight 1 Standard factory settings Bit 1 and 2 in OFF position Skylight 2 Bit 1 goes to ON position Skylight 3 Bit 2 goes to ON position Skylight 4
3. US remote control but does not require any programming KEY A 5 grey KEY B 6 brown ZKC fea For detailed information how to install and operate the ZKC US please refer to ZKC US manual delivered with the controller 13 Network connection of the FVE skylights In situation when you have few FVE skylights installed in a block of skylights you can connect them into a network to make the operation easier and to be able to operate the skylights with one remote In order to connect the skylights in a network you need to connect the BUS A and BUS B sockets of each skylight together To feed the cable inside of the skylight drilling in the skylight s frame is required no 1 no 2 no 3 fo To 12 fo 12 KEY A 5 kya O KEY A 5 grey G O kere 6 Seve Oea 6 brom ZKC Te olLwercm To ollwercm fo KEY C 7 green BUS A 8 BUSA BUS A 8 9 BUS B 9 jo BUS B 9 O BUSB 9 Once the network is established it is neccessary to set on which channel of the remote control given skylight will be operated In order to do that you must change the bits configuration on the circuit board of each skylight see chapter Multiple skylight operation For ease of use it is also recommended to
4. transmitter In Figure 1 there is presented a general view of the ZRC US remote control with description of buttons and signaling numbers Note Every FVE skylight is delivered with one ZRC US remote control Active channel signaling Diode indicating preselection of channel 1 to operate skylight 1 Diode indicating preselection of channel 2 to operate skylight 2 Diode indicating preselection of channel 3 to operate skylight 3 Diode indicating preselection of channel 4 to operate skylight 4 SELECT button for changing channels Operating buttons pair No Button open skylight Button close skylight A 4 Operating buttons pair No Il Button open accessory 1 Button close accessory 1 5 Operating buttons pair No Ill Button open accessory 2 Button close accessory 2 on Dimension ZRC US A 157 mm B 38 mm C 19 mm Figure 1 ZRC US remote control 12 08 14 3 13 2012 FAKRO 3 QUICK START UP Installation of ZRC US controller The holder of ZRC US controller should be attached to the wall or other permanent building element by means of two screws driven into cylindrical plugs inserted into openings drilled in the wall 1 Screw the bottom section of the holder to the wall using the included screws which are driven into plugs inserted into the drilled openings yy sy y sD
5. use one ZKC US controller connected to one of the FVE skylights 14 Trouble shooting If you are facing any problems with the operation of FVE skylight please visit our website for your country in service tab where you will find service tips If you still will not be able to find the proper information on the website feel free to contact our sales office in your country 12 08 14 13 13 2012 FAKRO
6. Bit 1 and 2 go to ON positions 4 After changing the bits configurations on required skylight s No 2 No 3 and No 4 put back the cover s and mosquito screen s nn Restore the power supply of the skylight s 6 Assign the remote to each of the new skylight s 6 1 Pressing the preselection button of the remote choose the right channel corresponding to the given number of the skylight red light flashing Diode indicating channel 2 to operate skylight 2 6 2 Using small screwdriver press and hold the programming switch through the hole in the skylight s operator side plastic Simultaneously point the remote towards the skylight and press one of the skylight operating buttons A Y Once it s done the remote control code is stored in the skylights control unit memory 12 08 14 8 13 2012 FAKRO 6 3 Repeat the steps 6 1 6 2 for each of the added skylights Please remember to select the right channel number on the remote 7 After the programming is done corretly you will be able to operate up to four skylights with the same remote by changing the channel on the remote Operation of the internal blinds installed on each of the FVE skyligths is always done by the second set of buttons on the ZRC US remote Skylight 1 Skylight 2 Skylight 3 Skylight 4 8 ADVANCED AUTOMATIC MANUAL bits configuration fo
7. FAKRO FVE skylight user manual Contents 1 Impo rta t WF OP AO sacs iexsitessetnasevsdasduwielnenmiwaesh lens E E A E EEEE EA ER EE Ea EEO EREE EEEN 2 2 QUICK START UP Description of the remote control ZR CG i icancssnccssnceosotsasesssesermseswsedennciumiestiaansetmersawtereinas 3 3 QUICK START UP Installation of ZRC US controller cece ccessccesseccesseecesseecesseeeseesseeeceeeesseeeceseseaees 4 4 QUICK START UP Operation of single skylight with ZRC US remote control eeeeceeeteeeeteeeeeteeeeees 5 5 QUICK START UP Internal blind operation of the FVE skylight with ZRC remote control ceee 6 GADVANCED Circuit board wiring Cig Stats t c sexvacaxand sasstassaandvindandesrsevadeudaiadecastneasziaaiauaneaeanmeasdaneniontins 6 7 ADVANCED Multiple skylight operation use of channels 2 3 4 eeeeseeteeeeeeteeeeeeneeeeeeeeteeeeeeeees 7 8 ADVANCED AUTOMATIC MANUAL bits configuration for skylight and accessories operation 9 9 ADVANCED Change of the security code Optional ccissscsseesisicerccsnscaesssnsancaqannsasaeseseascadeasabasaesaceasansentzoeses 11 1G Manual emergency closing Of the SY IONE os icaxcsscacenisesasaranecasont snseoonncukviunsdesiunntsaieedunialeanveauienduatasanexaeuiuanstnieds 12 VIRAM STIS OTS eoira a a a teense as ee 12 12 ADVANCED Connection of the ZKC US Keyboard ccccecccccssecesscesseceseeessecsseeeseeceseeeeeceeeeeseeeeseenneees 13 13 ADVANCED Network conn
8. Multiple skylights operation 12 08 14 5 13 2012 FAKRO 5 QUICK START UP Internal blind operation of the FVE skylight with ZRC US remote control In order to ensure smooth blind operation the blind must be properly installed and connected to the power source according to the installation instruction delivered with the blind In order to operate the internal blind black out or venetian blind make sure the channel 1 of the remote is selected To open or close the blind point the remote control towards the skylight and using second pair of the buttons press the open button to open and close button to close the blind Please remember the blinds will also work in AUTOMATIC mode a O M1 MAO S74 o er N mp S M2B 2 SUPA pma 3 M3 ay Q NS om KEY A 5 trans ormer gt C ed sw2 _ OF kevB 6 ZKC O olLkercm seo E e o olll oonan aoa Om BUSB OL IR WIND RAIN RAIN Outputs M1 Skyligth s motor M2 internal blind motor M3 external blind motor recommended also for SJP EV venetian blind Inputs 24V power input of 24VDC ZKC US control keyboard NETWORK network connecti
9. de change the position of BIT 4 to OFF possition MANUAL mode is recommended for electric venetian blinds SJP EV as it allows to set the slats inclination more precisely As standar output M3 is set in MANUAL mode so you can also use this output to connect the venetian blind to the circuit board 12 08 14 10 13 2012 FAKRO Explanation of all possible bits confirguration on bits panel SW2 Setting the configuration of the operation by changing the bits positions Bit number Bit position ON OFF Terminal nr BIT5 Activated rain and wind sensors for channel Deactivated rain and wind sensors for 1 closes the skylight channel 1 OUTPUT 1 Automatic operation for channel 1 Manual operation for channel 1 M1 BIT 6 Full opening or closing after single button Opening closing process activated when press No 1 button is pressed BIT 3 Activated rain and wind sensors for channel Deactivated rain and wind sensors for 2 channel 3 OUTPUT 2 Automatic operation for channel 2 Manual operation for channel 2 M2 BIT 4 Full opening or closing after single button Opening closing process activated when press button is pressed Activated rain and wind sensors for channel Deactivated rain and wind sensors for BIT 1 3 channel 3 OUTPUT 3 Automatic operation for channel 3 Manual operation for channel 3 M3 BIT 2 Full opening or closing after single button Opening closing process activated when press butto
10. ection of the FVE skylights 0 ccccccccssscssseseneceseeeeeeceeeeseeceaeeeseeceeeseneeeees 13 14 Tro ble shooting sais cestaaesnadcenizasseeaadepaaksicaed setaces ecu ssacanmeacceniaiasaayieuacdoaapiauenateiaamasmelynexideueaderidveiaateeasanin utaeueles 13 www fakro com 12 08 14 1 13 2012 FAKRO 1 Important information Read the entire instruction before using the FVE skylight Make sure that insect screen is installed prior to operation of the skylight FVE skylight and accessories when connected are factory set to operate in AUTOMATIC mode It means that one press of open button will open the skylight to it s maximum When close button is pressed the skylight will close totally In order to stop the skylight in desired possition you need to press one time the close button during opening and open button during closing process of the skylight Remote control ZRC US has been designed for the use with FAKRO products Use of this unit with other equipment may cause malfunction The batteries provided are AA 1 5V batteries After removing the packaging make sure the equipment has not been damaged Before connecting the equipment make sure that the supply voltage corresponds to the appliance voltage indicated on the technical data label on the equipment This equipment must be only used for the purpose which it has been built for The manufacturer cannot be considered liable on any damages or prob
11. in sensors When the skylight is wide open it takes about 30 seconds before the skylight is completely closed Therefore during heavy rain water may enter the room before the skylight is closed fully Please pay particular attention if furniture is placed below the skylight The rain sensors does not react to very fine weak rain fog or dew Dirt on the rain sensors may cause operating problems Therefore it is recommended to clean the rain sensor with a soft damp cloth when needed Remember to switch off the power before cleaning If the skylight is fully closed due to rain and you will open it afterwards during the closing initiated by the rain sensor you can not stop the skylight from closing the rain sensors will remain inactive for next 10 minutes During that time the skylight can be closed only with the use of the ZRC US remote control 12 08 14 12 13 2012 FAKRO 12 Connetion of the ZKC US controller As an option each of the FVE skylight can be additionally operated by ZKC US keyboard In order to connect the ZKC US keyboard to a FVE skylight you must switch off the power remove the mosquito screen and the bottom cover Wiring requires also to drill a hole in bottom part of the frame to feed through the cable so it is recommended to plan the use of ZKC US keyboard before any plastering will take place Below drawing shows wiring diagram between the FVE circuit boards and ZKC US keyboard ZKC US keyboard works in similar way as ZRC
12. ing small screwdriver press and hold the programming switch through the hole in the side plastic of the skylight s operator cover Simultaneously point the remote towards the skylight and press one of the skylight operating buttons A VW Once it s done the remote control security code is stored in the skylights control unit memory Important After the security code change repeat step No 7 with every skylight that will be operated with the remote D 10 Manual emergency closing of the skylight In case of power failure the skylight if opened can be closed manually To close the skylight remove the mosquito screen and using the screwdriver unscrew the screw locking the motor chain in the chain socket Holding the sash align the chain along the cover and close the window Important This is only emergency solution Do not leave the house unattended as the skylight is possible to be opened from outside As soon as the power is restored put the chain to it s original position as well as the mosquito screen As the power can be restored at any time during unlocking the chain and the closing procedure of the skylight can be activated by rain sensors when raining to avoid personal injuries make sure the skylight is disconnected from the power main 11 Rain sensors Rain sensors are pre installed at the factory The rain sensors ensure that the skylight automatically closes if it rains through the skylight Do not paint or varnish the ra
13. lems arising from improper use The installation has to be carried out in accordance with the instructions of the manufacturer The non observance of these instructions could compromise safety The power must be switched off when connecting the skylight installing accessories and whenever the cover of the electiric elements is removed Call for a service when the product does not work properly Make sure children will not be able to play with the skylight keep the remote away from children Switch off the power to the system before you have your hand or body out of the skylight The motor automatically closes the skylight when any of the rain sensors get wet To clean the skylight or perform the maintenance always switch of the power to the system Disposal of used batteries shall conform with relevant environmental regulations 12 08 14 2 13 2012 FAKRO 2 QUICK START UP Description of the remote control ZRC US The ZRC US remote control enables remote control of electric products compatible with the infrared system like FVE skylight The ZRC US controller can operate up to 4 skylights separately The single button in the upper section No 2 Figure 1 is used for selection of one of the four channels No 1 Figure 1 with which the devices can be assigned The fifth channel is signalized by all 4 LEDs It allows to operate all of the devices at the same time The ZRC US controller is equipped with a infra red
14. n is pressed 9 ADVANCED Change of the security code optional To obtain maximum security it is recommended to frequently change the security code Setting your personal code will give an assurance that the skylight s can be operated only from your own remote control unit To change the security code it is necessary to uncover the back of the remote control exposing programming button P below the battery and follow the steps Important After the security code change YOU MUST repeat programming procedure from Chapter 7 with every skylight that will be operated with the remote 1 Remove the back cover of the remote and press the programming button P 2 12 08 14 11 13 2012 FAKRO 3 Choose any combination of the security code by pressing any of the buttons from A to F on the remote 4 Defalut the security code is set in following combination 0 0 0 0 0 0 By pressing any of the A F remote buttons you change the status from 0 to 1 If you press A C E buttons the code will change into 1 0 1 0 1 0 Your new personal code if you press A button write 1 if you do not press B button write 0 under it Do the same for the remaining letters A B C D E F 5 Accept the code by pressing programming button P again Two internal diodes will light on indicating that the code is now stored Replace the back cover of the remote 7 Us
15. on of multiple skylights SW 1 bits panel SW2 bits panel Power cable consists of 3 wires brown blue and yellow green The yellow green color wire is grounding The other two wires can be connected to power source in either way 12 08 14 6 13 2012 FAKRO 7 ADVANCED Multiple skylight operation use of channels 2 3 4 ZRC Remote infrared control unit allows to control separately up to 4 skylights with installed blinds As mentioned in chapter Operation of the FVE skylight with ZRC US remote control ZRC US remote control is delivered with a skylight and is programmed to operate only the skylight on channel 1 In order to operate additional skylights with the same remote it is required to program channel 2 3 4 respectively the ZRC US remote control and the FVE skylights we want to add The number of ZRC US remote control channels needed to be programmed equals the number of extra skylights to be operated with the one ZRC US remote control If you want to add just one extra skylight you need to program one extra channel 2 on the remote If two extra FVE skylights are to be added channels 2 and 3 need to be programmed In case of 4 skylights all four channels must be programmed as each channel works with one skylight only Once all of the addtional max three skylights are installed and working each skylight to be checked with the ZRC US remote control the skylights have been delivered with as a first step
16. r skylight and accessories operation Each FVE skylight output M1 and accessory if installed output M2 are factory set to work in AUTOMATIC mode Accessory output M3 is set to work in MANUAL mode Depending on the individual preferences there might be a need for changing the outputs configuration on skylight s circuit board Panel outputs can work depending on the configuration in AUTOMATIC once the button is pressed the motor runs the whole cycle of opening or closing or MANUAL mode motor works only when a button is pressed Each FVE skylight has standard factory bits setting bits panel SW 2 as follows to see the bits disconnect the skylight from the power source remove the mosquito screen and the bottom cover 12 08 14 9 13 2012 FAKRO f Output M2 internal bind VY Output M3 4p ie Output MI recommended tor O 7 l FVE opening closing motor SJP EV venetian blind C hiiti Above drawing shows bits configuration bits panel SW2 for all outputs Output M1 and M2 work in AUTOMATIC mode BIT 4 and 6 are in ON position Such bits configuration depicts standard setting for operation skylights motor M1 and internal blind M2 In order to change the skylights opening from AUTOMATIC to MANUAL mode change the position of BIT 6 to OFF position however we do not recommend this option for skylights operation In order to change the internal blind operation output M2 mode from AUTOMATIC to MANUAL mo
Download Pdf Manuals
Related Search