USER GUIDE
Contents
1. 06 Digital Input 2 07 Digital Input 3 08 Digital Input 4 09 Digital Input 5 10 Digital Input 6 11 Digital Input 7 12 Digital Input 8 13 Output common 3A 14 Relay output 1 15 Relay output 2 16 17 Counter input 1 18 Counter input 2 19 Power supply 20 Power supply 9 5 JOV POWER SUPPLY INPUTS AND COM PORT MUST MEET THE DEMANDS PLACED ON SELV SAFETY EXTREMELY LOW VOLTAGE CIRCUITS ACCORDING TO EN60950 IEC950 Regulated 3 3V 50 mA MAX available at terminal 04 respect to negative terminal 01 On battery equipped units such power supply is provided also when main power supply is missing to prevent permanent damage to battery external loads must be disconnected when voltage drops below 3Vpc COM PORT Easy configuration local control tracing and other advanced features are available through serial communication link Configuration software MobiSuite for PC running Microsoft Windows is available for free download at www contrive it RJ45 DBI RS 232 aa aap A bs 2 GND 5 5 ao oe i D Hardware handshake 4 SPK G MobiLink RS232 cable 5 CTS 8 IS 2505 00 01 oS SER MobiLink USB cable f RTS 7 2505 00 03 8 5V CAN BE USED TO POWER THE UNIT ANALOG INPUTS Up to 2 analog signal can be connected at terminals 02 03 respect to negative terminal 01 Select input mode by means of dipswitch G before to operate the unit Software configuration available for ea2. WHEN DISPOSING BATTERIES DO NOT DISPOSE OF IN FIRE ANTENNA The antenna must be connected to the RF interface implemented as a 50Q con nector available in 2 different options External FME male coaxial jack at the end of a short RG178 cable stub exiting from the bottom left side of the unit m Internal IPEX connector suitable for embeddable antennas OFF GREEN Charge completed RED GREEN Bad or NO battery The antenna must fulfil the requirements given below 880 to 1710 to 824 to 1850 to 925 to 1805 to 869 to 1930 to RX max les 1 usur PX max Typical gain O dBi in one direction at least The gain must not exceed 8 4dBi 850MHz and 3 5dBi 1900MHz We recommend a VSWR max of 1 5 1 although a VSWR max of 2 1 can be accepted without affecting performance and certification The DC impedance is floating but there is no problem when using antennas that presenta short to ground COPYRIGHT 2012 CONTRIVE SRL ITALY SOME RIGHTS RESERVED INFORMATION CONTAINED IN THIS DOCUMENT ARE SUBJECT TO CHANGE WITHOUT NOTICE PRODUCT NAMES CORPORATE NAMES OR TITLES USED WITHIN THIS DOCUMENT MAY BE TRADEMARKS OR REGISTERED TRADEMARKS OF OTHER COMPANIES AND ARE MENTIONED ONLY IN AN EXPLANATORY MANNER TO THE READERS BENEFIT AND WITHOUT INTENTION TO INFRINGE WHILE EVERY EFFORT HAS BEEN MADE TO MAKE SURE THE INFORMATION IN THIS DOCUMENT IS CORRECT CONTRIVE CAN NOT BE LIABLE FOR ANY DAMAGES
3. information contained on these devices may be affected This unit is under your responsibility Please treat it with care respecting all local regulations It is nota toy keep itin a safe place and out of the reach of children Treat the SIM card with the same care as your credit card do not bend or scratch or expose it to static electricity Keep your unlock and PIN codes in safe place Both fixed and mobile applications are allowed as defined below Fixed means that the device is physically secured at one location and is not able to be easily moved to another location Mobile means that the device is designed to be used in other than fixed locations and generally in such a way that a separation distance of at least 20 cm 8 inches is normally maintained between the transmitter s antenna and the body of the user ornearby persons Do contact an authorized service center in the unlikely event of a fault in the unit WARRANTIES CONTRIVE GUARANTEES FOR TWO YEARS FROM THE DATE OF MANUFACTURE OF ITS PRODUCT TO REPLACE OR AT ITS OPTION TO REPAIR ANY PRODUCT OR PART THEREOF WHICH IS FOUND DEFECTIVE IN MATERIAL OR WORKMANSHIP OR WHICH OTHERWISE FAILS TO CONFORM TO THE DESCRIPTION OF ITS SALES ORDER CONTRIVE MAKES NO WARRANTY OF MERCHANTABILITY OR ANY OTHER WARRANTY EXPRESS OR IMPLIED IN NO EVENT SHALL CONTRIVE BE LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE WHICH MAY ARISE IN CONNECTION WITH SUCH PRODUCTS THE
4. 50 IEC950 maximum allowed voltage is 60VDc COUNTER INPUTS Two special digital inputs are available at terminals 17 18 Inputs can be used as a standard digital input in addition to 8 channels already available without LED indication Independent debounce time setting for each input in the range 1 300 seconds Inputs can operate also as a pulse or time counter SPST contacts magnetic reed or hall sensor and electronic switches can be used Internal power supply is available at terminal 04 using electronic switches this is the positive leg Input voltage 3 9 VDC Input current 5mA 4V Output voltage 4V DC 20 AT TERMINAL 04 Pulse width gt 200 20 ms CONFIGURABLE Frequency lt 2 5 Hz 17 18 Wi TO TERMINAL 04 OUTPUTS Two SPST relay contacts are available for process or appliance control at terminals 14 15 status reported on LED B Common return at terminal 13 Rated current 3 A Rated voltage 250 VAC Breaking voltage 277 VAC Max breaking capacity 750 VA Minimum contact load 1 mA 5 VDC Cadmium free contacts Insulation to IEC60664 Voltage rating 277 V Pollution degree 2 category as basic insulation Ill category as reinforced insulation II Surge voltage coil contacts 5000VRmus Dielectric strength coil contacts 3000VRmus open contact circuit 750VRus 15 14 15 142 N To prevent relay contacts from damaging an external protection should be provided fuse or similar according to the re
5. COMMANDS FOR REGISTERED USERS Behavior of Mobi Control at incoming calls from Registered Users can be set to NO ACTION Clip feature is disabled nothing happens on incoming calls PULSE default 3 Selecting this mode incoming voice or fax call will turn on out 1 for the specified time Adata call will do the same on output 2 Call terminated without answer TOGGLE Incoming voice or fax call will toggle output 1 on to off or vice versa data calls will do the same on output 2 If the user waits online Mobi Control will confirm the operation by means of voice messages REVERSE Any incoming call from registered users will start a sequence output 1 pulse pause output 2 pulse all times configurable Call terminated without answer ae Mobi Control answers the incoming call accepting up r 5 5 to 5 control codes on the telephone keypad 0 star toconfirm once all commands are issued hash todelete and start from the beginning fea ee ee CONFIRM STATUS DELETE Voice prompt will guide during the operation INSTALLATION This unit can be installed on any standard EN 50022 rail by simple snap in For safe operation the unit must be installed only by qualified personnel in an enclosure which prevents accidental contact with hazardous voltages Protection degree IP40 must be guaranteed raised to IP54 for open air application F RJ socket COM port A Analog and digital input terminals 12 x 2 5mm A
6. CONTRIVE S R L Via Enrico Fermi 18 24040 SUISIO Bergamo Tel 39 0 35 4948236 Fax 39 0 35 4933759 SCONTRIVE B2500 EN 1213 www contrive mobi Mobi Control GSM REMOTE CONTROL aO t e E CE 0681 This device complies with Part 15 of the FCC Rules CONTAINS FCC ID N7NQ2687 USER GUIDE Mobi Control OUTPUTS NO OUTPUT RELAYS 2500 NO BATTERY 0 Li Poly BATTERY B gt Oo 9m 1 OUTPUT RELAY 1 XM SE Nu Tg 2 OUTPUT RELAYS 2 sa we S w OA ANALOG INPUTS gt sz 89 NO INPUTS 0 O F 6O Fa 2 INPUTS 2 QO Fe Ho Os ANTENNA ui O ao oe EXTERNAL FME X vO ga INTERNAL I Lu ee HE BATTERY FO Z0 ep D z CARE AND MAINTENANCE Your Mobi Control is the product of advanced engineering design and craftmanship and should be treated with care The suggestion below will help you to enjoy this product for many years Do not expose the unit to any extreme environment where the temperature or humidity are out of operating range Do notuse or store the unitin dusty or dirty areas Donotuse chemical cleaning agent on the unit or the SIM card Donotattemptto disassemble the unit or remove any part or label Donotexpose the unit to water rain or spilt beverages It is not waterproof Donotabuse the unit by dropping knocking or violenty shaking it Rough handling can damage it Do not place the unit alongside computer discs credit or travel cards or other magnetic media The
7. NALOG COUNTER THRESHOLDS SETTINGS zerol RESET COUNTER 1 zero2 RESET COUNTER 2 log ASK FOR 98 EVENTS LOG MEMORY clearlog DELETE EVENTS LOG MEMORY logstatus SAVE CURRENT STATUS TO LOG MEMORY logemail SEND CURRENT STATUS TO EMAIL ADDRESS beep PLAY AN AUDIO TONE melody PLAY AMELODY speech PLAY A VOICE MESSAGE way GEOGRAPHIC INFORMATION 9 neton ENABLE RADIO AND NETWORK REGISTRATION netof f DISABLE RADIO AND RELEASE NETWORK netnew PERFORM ANEW NETWORK REGISTRATION divert ENABLE INCOMING CALL DIVERTING nodivert DISABLE INCOMNG CALL DIVERTING Complete commands list and details here www contrive mobi mobicontrol SHORTCUT COMMANDS FOR REGISTERED USERS Users stored into device Phonebooks are allowed to use shortcut commands that doesn t require password 7 commands are predefined editables S1 Set output 1 ON S2 Set output 2 ON R1 Reset output 1 OFF R2 Reset output 2 OFF P1 Pulse output 1 default 3 P2 Pulse output 2 default 3 D Status SMS request Specifying a time interval after the set command outputs will be released once set time has elapsed 1 DDhhmm hh hours 00 23 mm minutes 00 59 ss seconds 00 59 or at a specified expiry date time S1 DDMMYYhhmm DD day 01 31 MM month 01 12 YY year 00 99 hh hours 00 23 mm minutes 00 59 Example S1 083000 S2 2504141230 text D alien trailer turn ON output 1 for 8 hours and 30 minutes turn ON output 2 until April 25 2014 12 30 send back a status SMS CALL
8. R INPUTS P1 P2 PULSE COUNTER INPUTS P1 P2 GEO POSITION failure restore low high low high on off opening closing low high thresholds opening closing accumulated time threshold accumulated pulses threshold low high ratio thresholds MCC MNC LAC CI change send alerts to recipients using different formats and at configurable intervals PHONE CALL SMS EXTENDED SMS TWEET EMAIL voice message on answer custom text including device status custom text custom text and device status For each input output channel is possible to define a name and set the operating parameters The behavior of Mobi Control can be configured by setting some rules USERS 1 USERS 2 RECIPIENTS INCOMING CALLS ORIGINATED CALLS INCOMING SMS ORIGINATED SMS WEB SERVICES PLC 10 enable according to day hour enable according to day hour enable according to day hour behavior timing feedback behavior duration inter call pause confirmation feedback mode pause between sending connectin mode name event commands By means of PLC rules is possible to define up to 10 commands the same available from remote that will be carried out upon the occurrence of a local event creating a small programmable controller The same commands can be scheduled to be carried out by configuring up to 100 operations on a specified date only once or periodically daily weekly or yearly If the Web Services have been activ
9. WARRANTY DOES NOT APPLY IN CASE OF IMPROPER USE SAFETY INFORMATION Do not install this unit near medical devices like pacemakers or hearing aids This unit may interfere with the operation of these devices Switch off this unit when flying Secure it so that it cannot be switched on inadvertently Do not install this unit near petrol stations fuel depots chemical plants or blasting operations when this unit can disturb the operation of technical equipment Interference can occur if this unit is used near televisions radios or personal computers If the device has been stored in a cold environment condensation can occur Before starting operations the device must be absolutely dry Thus an acclimatization period of at least three hours must be observed In order to avoid possible damage we recommend that you only use the specified accessories These have been tested and shown to work well with this unit ES Tesimestewces This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions this device may not cause harmful interference and this device must accept any interference received including interference that may cause undesired operation This device should be installed only by qualified personnel Carefully read the instruction manual in its entirety and keep it safe for future reference It is essential to Know the information and comply with the instructions given in th
10. WG14 Output green LED indicators C GSM operation blue LED indicator OFF CO000000000 No power supply Oo of ON PERMANENTLY Module switched ON Not registered on the network missing SIM or invalid PIN SLOW FLASH 200ms ON 2s OFF Module switched ON Registered on the network QUICK FLASH 200ms ON 600ms OFF Module switched ON Registered on the network Communication in progress J O Digital input red LED indicators m Outputs counter inputs and power supply terminals 8 x 2 5mm AWG14 X Antenna connector NOT AVAILABLE FOR IPEX VERSION G Analog input selector LE Disconnect all power LZ supplies and battery before to insert or remove the SIM card Y Replace the plastic cover gt before to operate the unit F SIM card holder 3V and 1 8V SIM card allowed SIM PIN Put your SIM card into a cellular phone and program it so it won t ask for the PIN the SIM card is open and someone could steal the SIM card use it and read the information inside You may protect the SIM card later using MobiSuite configuration software o WARNING If you insert a SIM card that asks for a PIN number different from that stored into Mobi Control the device will not operate If you enter the PIN 3 times incorrectly SIM card will lock up and you must provide the PUK PIN Unblocking Key 01 Negative 02 Analog Input 1 03 Analog Input 2 04 Positive 3 3VDC 05 Digital Input 1
11. Y DEVICE Web interface once a web accountis available www webadmin mobi The configuration interface and Web Control requires a data connection consider enabling this interface depending on the application and evaluating the tariff plan related to data transfer proposed by your Operator When you configure the access point to the network APN the device automatically activates the data link and create its own account The configuration of the access point can be made using Mobi Suite alternatively you can send the following SMS to the device xxxx APN adr user pwd XXXX device password DEFAULT 0000 APN access point PROVIDED BY YOUR OPERATOR user APN username LEAVE BLANK IF NOT REQUIRED pwd APN password LEAVE BLANK IF NOT REQUIRED Example 0000 APN apn operator com mymobi mypassword Once you have completed the activation Mobi Control will send you back an SMS including the identifier to be used to access its Web account You can set up some information about the device IDENTIFIER to be included in all sent messages PHONE NUMBER EMAIL ADDRESS PASSWORD CLOCK SETTINGS assigned to SIM card to be used within messages to be used for local remote access manual automatic Mobi Control can be configured so that the occurrence of specific events POWER SUPPLY BATTERY INTERNAL TEMPERATURE RELAY OUTPUT 01 02 DIGITAL INPUTS 11 18 ANALOG INPUTS Al1 A2 DIGITAL INPUTS C1 C2 TIME COUNTER INPUTS T1 T2 PULSE COUNTE
12. ated you can define operations associated with sunrise and sunset time updated weekly by date and geographical area The incoming SMS messages that contain no commands are discarded But it is possible to define some forwarding rules based on the sender s phone number and or based on keywords contained in the text in order to send these messages to a phone number of your choice DIMENSIONS mm Please perform the following tasks after receiving the product Inspect the unit for damage Ifthe unit appears damaged upon receipt contact the shipper immediately Verify receipt of the correct unit by checking the label on the right side of the unit If you have received the wrong model or the device does not function properly contact your supplier REMOTE CONTROL Up to 5 commands can be issued to Mobi Control within SMS Tweet Email Web Message must include device password default 0000 editable Commands will be recognized both uppercase lowercase and mixed nested within other text wherever placed inside the incoming message out SWITCH OUTPUTS ON OFF startl ENABLE GROUP 1 USERS stop1 DISABLE GROUP 1 USERS start2 ENABLE GROUP 2 USERS stop2 DISABLE GROUP 2 USERS alert ENABLE ALERTS TO RECIPIENTS noalert DISABLE ALERTS TO RECIPIENTS sms SENDADIRECT SMS tweet SENDADIRECT TWEET email SENDADIRECT EMAIL status ASK FOR DEVICE STATUS clock REAL TIME CLOCK SETTINGS setl CHANNEL 1 SETPOINT set2 CHANNEL 2 SETPOINT thr A
13. ch input fullscale value 1 100000 zero offset 0 90 unit any text Input range 0 20 mA x aa Voltage drop 2V 20mA Resolution 0 02 mA _ 1 12 1254 1254 Accuracy 1 Q Impedance 100 Q 01 02 03 ON ON Input range 0 10V vy Resolution 0 01 V 1234 12 Accuracy 1 Impedance 25 kQ ON ON Input range 0 2V y Resolution 0 002 V 1234 12 Accuracy 1 01 02 05 Impedance 5 kQ O NTC temperature sensor measuring in the range 10 60 C can be directly connected to analog inputs set inputs for 2V and enable NTC software linearization 1PRSROO1 B 1PRSR002 A ON ON Input range 0 2V y y Resolution 0 1 C 1234 1234 Accuracy 1 C Q NTC 10 KQ 25 C D C B 3435 25 85 C SHIELDED CABLE COULD BE USED FORLONG LINES SHIELD CONNECTED TO NEGATIVE TERMINAL 01 ONLY LEAVE OTHER SIDE UNCONNECTED Active devices could be powered directly from Mobi Control when voltage and output are compatible and total current consumption remains within 50 mA LM60 PRECISION TEMPERATURE SENSOR TEXAS INSTRUMENTS 1 Positive 2 7 12VDC 2 Out 6 25mV C 424mV OFFSET 3 Negative SET INPUT SWITCH 2V TEMP C OUT mV 128 C of aaa T 02 03 04 POWER SUPPLY This unit can be supplied either by alternating or direct current polarity independent in a wide voltage range Power supply connection terminals 19 and 20 The power supply must not be shared with other equipment sugg
14. e manual to ensure the fitting is installed used and serviced correctly and safely This RF unit is not designed for and intended to be used in portable applications within 20 cm or 8 inches of the body of the user and such uses are strictly prohibited This unit is not authorised for use as critical component in life support devices or systems unless a specific written agreement has been given If incorrectly installed in a vehicle the operation of GSM device could interfere with the correct functioning of vehicle electronics Verification of the protection of vehicle electronics should form a part of the installation Regulations must be considered to operate a vehicle s light or horn on public roads No complex software or hardware system is perfect Bugs are always present in a system of any size In order to prevent danger to life or property it is the responsibility of the system designer to incorporate redundant protective mechanism appropriate to the risk involved All units are 100 functionally tested Specifications are based on characterisation of tested sample units rather than testing over temperature and voltage each unit Contrive disclaims all liability for damage to the fitting or to other property or persons deriving from installation use and maintenance that have not been carried out in conformity with this instruction manual which must always accompany the fitting PRODUCT DESCRIPTION Mobi Control is an indus
15. ested power supply source is a simple 12Vac 10VA transformer 19 20 Supply Voltage 9 5 35 VDC 9 5 27 VAC Power consumption lt 200mW IDLE lt 5W PEAK AY An automatic 2 pole circuit breaker or equivalent protection capable of discon necting circuit in the event of short circuit or over current condition should be placed on the AC mains side of power supply unit Maximum permissible connection length between device and low voltage supply source is 3 m DIGITAL INPUTS Up to 8 SPST contacts can be wired to terminals 05 12 status reported on LED indicators D Internal power supply is available at terminal 04 Independent debounce time setting for each inputin the range 1 300 seconds Input voltage 3 9 VDC Input current 5mA 5V Output voltage 3 3V DC AT TERMINAL 04 1 2 3 4 5 6 7 8 AYLOIY 04 05 06 07 08 09 10 11 12 When inputs are supplied by external source negative must be connected to terminal 01 Insert a Zener diode to keep inputs voltage within 9VDC Multiple options can be used see example below m inputs 1 and 2 using internal supply inputs 3 and 4 using external 5VDC supply inputs 5 and 6 using external 12VDC supply reduced by zener diode 6 8V inputs 7 and 8 using external 24VDc supply reduce by zener diode 20V 24V 12V 5V 6 8V Z20V 1 2 3 4 5 6 7 8 JY YY 01 04 05 06 07 08 09 10 11 12 External power supply for inputs must meet SELV circuits requirements according to EN609
16. lay breaking capacity BATTERY This unit could be equipped with an high efficiency Lithium lon Polymer battery having a long life that largely depends on temperature and frequency of main power failures used in normal condition can last several years If the battery is already connected you just need to provide power supply to operate Mobi Control The battery charging process will start If the battery is not connected proceed as follows Disconnect power supply and all live circuits Remove front cover to access the inside 1 Push with two fingers on top and bottom sides of front cover to release it 2 Pull the front cover and keep it in a safe place 3 Unplug battery connector from the socket K 4 Replace the front cover to close the unit Disconnect the battery if the device is put out of service O O O O O O O O OOOO BATTERY SPECIFICATIONS Voltage 3 7 V 4 2V FULL CHARGE Capacity gt 320 mAh 1 26 Wh Temperature 20 60 C 0 45 C CHARGING Before a long period of inactivity switch off the unit to prevent deep discharge of the battery O O O O O OOO 999099909909 4 Le This operation can be accomplished using Mobi Suite terminal or from the console by issuing the command AT CPOF Ok ae RECYCLING OPTIONS Battery status is reported at any time by the LED located near the connector OFF OFF Charge OFF AVAILABLE IN YOUR AREA MUST BE CONSIDERED RED OFF Charge in progress
17. trial DIN rail GSM modem for the supervision and control of remote inputs and outputs by means of enhanced features available through GSM network Industrial standard interface and an integrated SIM card reader mean it can be used rapidly easily and universally to quickly implement new applications in telemetry telematics and remote control All interfaces are integrated in the housing The connections are suitable for use in domestic and industrial environments PRODUCT FEATURES Quad band GSM GPRS EDGE communication with manual automatic selection on bands 850 900 1800 1900 MHz for data sms data and voice applications Output power Class 4 2W for GSM850 and EGSM900 Class 1 1W for DCS1800 and PCS1850 Temperature 30 to 60 C 40 to 85 C when relays are not in use 20 to 60 C recommended for battery operating 5 to 95 non condensing storage amp transport 5 to 95 condensation allowed outside Enclosure EN 50022 rail 4 modules polycarbonate UL94 VO Overall dimensions mm71x90x58 WxHxD Weight 200 g Degree of protection IP 40 EN 60529 IEC 529 properly fitted Relative humidity CONFIGURATION Mobi Control is fully configurable by means of Mobi Suite freeware tool available for download www contrive mobi linked to device through local COM port generating configuration SMS to be sent to the remote device sending configuration through device Web account ONCE AWEB ACCOUNT HAS BEEN CREATED B
Download Pdf Manuals
Related Search