Bedienungsanleitung de Operating instructions en Mode d
Contents
1. This means that only original Hilti consumables components and spare parts may be used in the tool This warranty provides the free of charge repair or re placement of defective parts only over the entire lifespan of the tool Parts requiring repair or replacement as a result of normal wear and tear are not covered by this warranty Additional claims are excluded unless stringent na tional rules prohibit such exclusion In particular Hilti is not obligated for direct indirect incidental or con sequential damages losses or expenses in connec tion with or by reason of the use of or inability to use the tool for any purpose Implied warranties of merchantability or fitness for a particular purpose are specifically excluded For repair or replacement send the tool or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided This constitutes Hilti s entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties 11 declaration of conformity original Designation Rotating laser Type PRI 2 Year of design 2006 We declare on our sole responsibility that this product complies with the following directives and standards 2004 108 EC 2006 95 EC 2011 65 EU EN ISO 12100 Hilti Corporation Feldkircherstrasse 100 FL 9494 Schaan 4 Paolo Luccini He2. mounting an adapter check that the tool is screwed on securely g Keep the laser exit aperture clean to avoid meas urement errors h Although the tool is designed for the tough condi tions of jobsite use as with other optical and elec tronic instruments e g binoculars spectacles cameras it should be treated with care Although the tool is protected to prevent entry of dampness it should be wiped dry each time before being put away in its transport container To avoid confusion check to ensure that no other tool of the same or a similar kind is in use in the immediate vicinity 5 6 Electrical a Keep the batteries out of reach of children b Do not allow the batteries to overheat and do not expose them to fire The batteries may explode or release toxic substances Do not solder the batteries into the tool d Do discharge the batteries by short circuiting as this may cause them to overheat and present a risk of personal injury burns e Do not attempt to open the batteries and do not subject them to excessive mechanical stress f Always replace the complete set of batteries g To avoid pollution of the environment the tool must be disposed of in accordance with the cur rently applicable national regulations Consult the manufacturer if you are unsure of how to proceed h Do not use damaged batteries i Do not mix old and new batteries Do not mix batteries of different makes or ty
3. wall or the working surface The laser line can be shifted to the left or the right as desired by pressing the direction buttons right left 7 2 Working with the PRA 22 laser receiver accessory The laser receiver can be used at distances of up to 150 m or when working in unfavorable light The laser beam is indicated visually and by an audible signal NOTE For further information please refer to the PRA 22 oper ating instructions 7 3 Working in the horizontal plane In order to work in the horizontal plane the rotating laser must be set up with the rotation head facing upwards Set up the tool in a suitable position for the application e g on a tripod Press the on off button Shortly before leveling is complete the laser beam switches on and begins to rotate at a speed of 150 revolutions per minute 7 4 Working in the vertical plane To work in the vertical plane set up the tool so that the rotation head faces to the side This can be achieved by standing the tool on the pins so that the control panel faces upwards Slide the reference indicator upwards The tool can then be aligned with the aid of the laser reference point Alternatively the rotating laser can be mounted on a tripod with the PRA 70 71 wall bracket Press the on off button When leveling is complete the laser beam switches on and begins to rotate at a speed of 150 revolutions per minute 7 5 Vertical alignment of the laser beam The
4. R FDA 1040 2006 Laser class Class 3R visible Laser class class Illa 90 reference beam Continuous perpendicular to the plane of rotation Speed of rotation 0 90 min 150 300 min 600 Automatic cut out Self leveling range Operating status LED indicators Power supply Battery life Operating temperature range Storage temperature range Protection class Tripod thread Weight without batteries Dimensions L x W x H Failure to achieve accuracy of 20 1mm 10m within 120 seconds 5 in all directions On off battery status Slope 2 x alkaline size D Temperature 25 C 77 F Alkaline manganese 50 h 20 50 C 4 to 122 F 25 60 C 22 to 140 F IP 54 5 11 1 55 kg 3 5 Ibs 188 mm X 188 mm X 194 mm 7 4 x 7 4 7 6 5 Safety instructions In addition to the information relevant to safety given in each of the sections of these operating instructions the following points must be strictly observed at all times 5 1 Basic information concerning safety a Operate the tool only as intended and when it is in faultless condition b Do not render safety devices ineffective and do not remove information and warning notices c Operate the tool within the specified temperature range d The laser visibility glasses have no protective function and do not protect your eyes from laser light As the laser visibility glasses restrict color vision they
5. ad of BA Quality and Process Man agement Business Area Electric Tools amp Ac cessories 01 2012 fla Matthias Gillner Executive Vice President Business Area Electric Tools amp Accessories 01 2012 Technical documentation filed at Hilti Entwicklungsgesellschaft mbH Zulassung Elektrowerkzeuge Hiltistrasse 6 86916 Kaufering Deutschland FCC statement IC statement CAUTION This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interfer ence ina residential installation This equipment gener ates uses and can radiate radiofrequency energy and if not installed and used in accordance with the instruc tions may cause harmful interference to radio com munications However there is no guarantee that interference will not occur in particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment and off the user is encouraged to try to correct the interference by one or more of the following measures Re orient or re locate the receiving antenna e Increase the distance between the equipment and receiver Connect the equipment to an outlet on a circuit differ ent from that to which the receiver is connected e Consult the dealer or an ex
6. datum lines and heights Marking out partition walls vertical and or at right angles Aligning systems and facilities in three axes Observe the information printed in the operating instruc tions concerning operation care and maintenance The tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed Take the influences of the surrounding area into account Do not use the appliance where there is a risk of fire or explosion Modification of the tool is not permissible 2 2 Features The tool allows a single person to level or align in any plane quickly and with great accuracy Automatic leveling within 5 inclination The tool levels itself automatically after switching on LEDs indicate each operating status The tool can be set up directly on the floor on a tripod or on the PRA 70 71 wall bracket 2 3 Combination with the PRA 2 remote control unit The PRA 2 remote control unit can be used to control the PRI 2 rotating laser conveniently from a distance The remote control function can also be used to adjust alignment of the laser beam 2 4 Combination with the PRA 22 laser receiver The PRA 22 laser receiver facilitates indication of the laser beam at great distances For further information please refer to the PRA 22 operating instructions NOTE Depending on the version purchased the PRA 22 laser receiver may not be included among the items suppl
7. day it is tested with the specifications given in the operating instructions The tool will be readjusted if deviations from the man ufacturer s specification are found After checking and adjustment a calibration sticker applied to the tool and a calibration certificate provide written verification that the tool operates in accordance with the manufacturer s specification Calibration certificates are always required by companies certified according to ISO 900x Your local Hilti Center or representative will be pleased to provide further information 8 4 1 Checking accuracy Check the accuracy of the tool in the X axis and Y axis as follows 1 Setup the tool horizontally approx 20 m from a wall can be on a tripod 2 Mark the point on the wall mark A Use the PRA 22 laser receiver or the PRA 50 51 target plate if visibility is poor 3 the tool 180 about its own axis use the same axis 4 the point on the wall mark Use the PRA 22 laser receiver or the PRA 50 51 target plate if visibility is poor NOTE When the procedure is carried out carefully the distance between the marks A and B should be less than 2 mm at 20 m If the deviation is greater Send the tool to a Hilti service center for calibration 9 Disposal WARNING Improper disposal of the equipment may have serious consequences The burning of plastic components generates toxic fumes which may present a health hazard Batterie
8. e Hilti cannot rule out the possibility of interference with other devices e g aircraft navigation equipment 5 4 Laser classification for tools of the class 3R Tools of the laser class and class Illa should be operated by trained personnel only The area in which the tool is in use must be marked with laser warning signs The plane of the laser beam should be well above or well below eye height Precautions must be taken to ensure that the laser beam does not unintentionally strike highly reflective surfaces Precautions must be taken to ensure that persons do not stare directly into the beam The laser beam must not be allowed to project bey ond the controlled area When not in use laser tools should be stored in an area to which unauthorized persons have no access 5 5 General safety rules a Use the right tool for the job Do not use the tool for purposes for which it was not intended Use it only as directed and when in faultless condition b Check the condition of the tool before use If the tool is found to be damaged have it repaired at a Hilti service center c The user must check the accuracy of the tool after it has been dropped or subjected to other mechanical stresses d Check the accuracy of the measurements several times during use of the tool e When the tool is brought into a warm environment from very cold conditions or vice versa allow it to become acclimatized before use f If
9. elias PRI 2 Bedienungsanleitung Operating instructions Mode d emploi Istruzioni d uso Manual de instrucciones Manual de instru es Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Odnyiec Hasznalati utasitas Instrukeja obstugi Navod obsluze N vod na obsluhu Upute za uporabu Navodila za uporabo Instructiuni de utilizare Kulllanma Talimati fats LietoSanas pamaciha Instrukcija Kasutusjuhend Rik BAA NSW te 9 4 20m 180 20m ORIGINAL OPERATING INSTRUCTIONS PRI 2 rotating laser It is essential that the operating instructions are read before the tool is operated for the first time Always keep these operating instructions to gether with the tool Ensure that the operating instructions are with the tool when it is given to other persons Contents Page 1 General information 10 2 Description 11 3 Accessories 12 4 Technical data 12 5 Safety instructions 13 6 Before use 14 7 Operation 15 8 Care and maintenance 16 9 Disposal 16 10 Manufacturer s warranty tools 17 11 EC declaration of conformity original 18 These numbers refer to the corresponding illustra tions The illustrations can be fo
10. ied 2 5 Speed of rotation There are 5 different speeds of rotation 0 90 150 300 or 600 revolutions per minute When rotation is switched off the laser can be aligned manually 2 6 Horizontal plane automatic leveling After switching on the tool levels itself automatically in all directions by way of 2 built in servo motors 2 7 Vertical plane automatic leveling Vertical alignment is carried out automatically The servo buttons can be used to align pivot the vertical plane manually 2 8 Inclined planes The inclination slope can be set manually in the hori zontal mode This function is activated by pressing the slope button The servo buttons can be used to manually incline the horizontal plane 2 9 Automatic cut out When automatic leveling is activated for one or both axes the built in servo system ensures that the specified accuracy is maintained The tool switches itself off if leveling is unsuccessful when the tool is set up outside its self levelling range or movement is blocked mechanically The tool switches itself off when knocked off level vibra tion impact When the tool has switched itself off rotation stops and all LEDs blink 2 10 Increasing the visibility of the laser beam Depending on the working distance and ambient light visibility of the laser beam may be impaired The PRA 50 51 target plate and or the PUA 60 laser visibility glasses can be used to improve laser beam visibili
11. ion of the pictograms and other information Warning signs General Warning Warning Warning warning explosive caustic electricity substances substances Symbols min Revolutions Read the Return waste per minute operating material for instructions recycling before use On the tool LASER RADIATION AVOID DIRECT EYE EXPOSURE nm lt SmW max 675 6951 3 CLASS Illa LASER PRODUCT Do not stare into the beam Laser warning plates for the USA in accordance with CFR 21 1040 FDA On the tool Laser warning plate in accordance with IEC825 EN60825 1 2003 Location of identification data on the tool The type designation and serial number can be found on the type identification plate on the tool Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department Type Serial no 2 Description 2 1 Use of the product as directed The Hilti PRI 2 is a laser tool with a rotating laser beam and a reference beam set at 90 to the main beam The tool is intended mainly for indoor use When used for outdoor applications care must be taken to ensure that the general conditions are similar to those encountered indoors The tool is designed to be used for determining checking transferring levels verticals alignment plumb points slopes and right angles for example Transferring
12. laser beam can be aligned vertically by pressing the buttons on the remote control unit Manual alignment of the rotating laser must be carried out exactly 1 Position the rotating laser on the desired reference point and switch it on 2 Use the rotation or line function buttons to set the desired function for example projection of a medium sized line 3 You can then align this line manually The servo buttons can be used to move the line to the left or to the right maximum 5 7 6 Working with slopes 1 Mount the tool in a suitable position for the applica tion to be carried out e g on a tripod 15 To set slope first press the slope button the PRI 2 rotating laser After activating this function by pressing the slope button the remote control unit can then be used to set the required slope relative to the horizontal plane The laser beam can be adjusted in the desired direction by pressing the buttons Self levelling is deactivated when the slope function is in use 7 7 Switching off the shock warning The shock warning can be deactivated by pressing and holding the on off button when switching on the PRI 2 rotating laser The on off button must be pressed for at least 3 seconds Deactivation of the shock warning is indicated by the on off LED blinking red 8 Care and maintenance 8 1 Cleaning and drying Blow dust off the lenses Do not touch the laser exit aperture and the filte
13. perienced TV radio techni cian for assistance NOTE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired oper ation This device complies with the requirements defined in RSS 210 of IC Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired oper ation iL Hilti Corporation 9494 Schaan Tel 423 23421 11 Fax 423 234 29 65 www hilti com Hilti registered trademark of Hilti Corp Schaan W 3277 0313 00 Pos 1 1 1 Printed Germany 2013 Right of technical and programme changes reserved 9 8 O 331423 2
14. pes 5 7 Liquids Under abusive conditions liquid may leak from the bat tery Avoid contact If contact accidentally occurs flush with water In the event of the liquid coming into contact with the eyes rinse the eyes with plenty of water and consult a doctor Liquid ejected from the battery may cause irritation or burns DANGER The tool may be powered only by batteries type D cells manufactured in accordance with IEC 285 or by a PRA 82 battery 6 2 Indicators LED indicators On off lights green con stantly On off blinks green CAUTION If using the rechargeable battery please read the operating instructions for the battery charger DANGER Use only new batteries 6 1 Switching the tool Press the on off button After switching on the tool begins the self levelling pro cedure automatically and the green on off LED blinks After completion of the self levelling procedure the laser beam is set to rotate in the normal direction and switches itself on The laser begins to rotate automatically The green LED for the on off button lights constantly The tool is leveling itself The tool has leveled itself Slope lights red constantly Slope function is active LED indicators On off blinks red The shock warning is deactivated All LEDs blink Battery LED blinks red 6 3 Inserting new batteries 1 Open the battery compartment by pressing and pulling the grip on the ba
15. r with the fingers Use only a clean soft cloth for cleaning If necessary moisten the cloth slightly with pure alcohol or a little water NOTE Do not use any other liquids as these may damage the plastic components Observe the temperature limits when storing your equipment This is particularly important in winter summer if the equipment is kept inside a motor vehicle 25 to 60 gt 8 2 Storage Remove tool from its case if it has become wet The tool its carrying case and accessories should be cleaned and dried at maximum 40 C 104 F Repack the equipment only once it is completely dry Check the accuracy of the equipment before it is used after a long period of storage or transportation Remove the batteries from the tool before storing it for a long period Leaking batteries may damage the tool 8 3 Transport Use the Hilti toolbox or packaging of equivalent quality for transporting or shipping your equipment CAUTION Always remove the batteries before shipping the tool 8 4 Hilti calibration service We recommend that the tool is checked by the Hilti cal ibration service at regular intervals in order to verify its reliability in accordance with standards and legal require ments Use can be made of the Hilti calibration service at any time but checking at least once a year is recommended The calibration service provides confirmation that the tool is in conformance on the
16. s may explode if damaged or exposed to very high temperatures causing poisoning burns acid burns or environmental pollution Careless disposal may permit unauthorized and improper use of the equipment This may result in serious personal injury injury to third parties and pollution of the environment E Most of the materials from which Hilti tools or appliances are manufactured can be recycled The materials must be correctly separated before they can be recycled In many countries Hilti has already made arrangements for taking back old tools and appliances for recycling Ask Hilti customer service or your Hilti representative for further information For EC countries only Do not dispose of electrical appliances together with household waste In observance of the European Directive on waste electrical and electronic equipment and its imple mentation in accordance with national law electrical appliances that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility Dispose of the batteries in accordance with national regulations 10 Manufacturer s warranty tools Hilti warrants that the tool supplied is free of defects in material and workmanship This warranty is valid so long as the tool is operated and handled correctly cleaned and serviced properly and in accordance with the Hilti Operating Instructions and the technical system is main tained
17. should be worn only when working with this tool and must not be worn while driving a vehicle on a public road e Keep laser tools out of reach of children f Failure to follow the correct procedures when open ing the tool may cause emission of laser radiation in excess of Class 3R Have the tool repaired only at a Hilti service center g Take the influences of the surrounding area into account Do not use the tool where there is a risk of fire or explosion 5 2 Proper organization of the work area a Secure the area in which you are working and take care to avoid directing the beam towards other persons or towards yourself when setting up the tool b Avoid unfavorable body positions when working from ladders Make sure you work from a safe stance and stay in balance at all times c Measurements taken through panes of glass or other objects may be inaccurate 9 Ensure tool is set up a steady level surface not subject to vibration Use the tool only within its specified limits 5 3 Electromagnetic compatibility Although the tool complies with the strict requirements of the applicable directives Hilti cannot entirely rule out the possibility of the tool being subject to interference caused by powerful electromagnetic radiation leading to incorrect operation Check the accuracy of the tool by taking measurements by other means when working under such conditions or if you are unsure Likewis
18. ttery compartment cover The tool cannot begin operation Cause The tool has been moved it cannot level itself Battery power should last a further ap prox 2 hours 2 Insert the batteries in the battery compartment care to observe correct polarity 3 Close the battery compartment cover 7 Operation NOTE The functions Speed of rotation and Line function can also be controlled directly from the PRI 2 rotating laser 7 1 Working with the PRA 2 remote control unit The PRA 2 remote control unit makes working with the rotating laser more convenient and is required in order to make use of certain functions 7 1 1 Selecting the speed of rotation revolutions per minute After switching on the PRI 2 rotating laser always begins to operate at a speed of 150 revolutions per minute Working at a slower speed of rotation can however make the laser beam appear much brighter The speed of rotation can be altered by pressing the speed of rotation control button the required number of times 0 gt 90 gt 150 gt 300 gt 600 gt 0 7 1 2 Line function The area of the laser beam can be reduced to a line by pressing the line function button The laser beam then appears considerably brighter The length of the line can be adjusted by pressing the line function button the desired number of times 0 gt 5 gt 10 gt 15 gt 0 The length of the line depends on the distance between the laser and the
19. ty When laser beam visibility is reduced due to bright sun shine for example we recommend use of the PRA 22 laser receiver accessory 2 11 Items supplied with the PRI 2 rotating laser PRI 2 rotating laser PRA 2 remote control unit PRA 50 51 target plate Operating instructions Manufacturer s certificate Batteries Hilti toolbox a ke 2 12 Items supplied with the PRI 2 22 rotating laser with laser receiver PRI 2 rotating laser PRA 2 remote control unit PRA 22 laser receiver PRA 50 51 target plate Operating instructions Manufacturer s certificates Batteries Hilti toolbox ONO MO A Aaa 3 Accessories Designation Short designation Receiver PRA 22 Target plate PRA 50 51 Laser receiver holder PRA 77 Wall mount PRA 70 71 Battery charger PUA 80 Battery PRA 82 Various tripods All Hilti tripods are equipped with a s thread Measuring staff All Hilti measuring staffs Laser visibility glasses PUA 60 4 Right of technical changes reserved NOTE Right of technical changes reserved Range of remote control unit circle diameter 1 60 3 200 ft Range of laser receiver circle diameter With laser receiver 2 300 m 6 1000 ft Accuracy Temperature 24 C 75 F Horizontal distance 10 m 60 ft 1 mm s2 635 lt Class 60825 1 2003 635 lt 8mW 21 CF
20. und on the fold out cover pages Keep these pages open while studying the oper ating instructions In these operating instructions the designation the tool always refers to the PRI 2 rotating laser Components operating controls and indicators PRI 2 rotating laser 90 reference beam Laser beam plane of rotation Rotating head 4 Laser exit aperture 5 Infrared receiving window 6 Control panel 7 Grips 8 Pins 9 Vertical reference indicator 40 Battery compartment 1 Base plate with 5 thread PRI 2 control panel A 2 On off shock warning deactivation 3 On off LED 4 Slope activation button 5 Slope LED 16 Battery condition indicator LED 17 Line function button Speed of rotation button PRA 2 remote control unit Command sent LED 00 Speed of rotation button 21 Direction buttons left right Line function button 03 Servo button for adjusting alignment 1 General information 1 1 Safety notices and their meaning DANGER Draws attention to imminent danger that will lead to serious bodily injury or fatality WARNING Draws attention to a potentially dangerous situation that could lead to serious personal injury or fatality CAUTION Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property NOTE Draws attention to an instruction or other useful informa tion 1 2 Explanat
Download Pdf Manuals
Related Search