PCI-DAS08 User's Guide - from Measurement Computing
Contents
1. Surge immunity Criteria A N61000 4 6 1996 Radio Frequency Common Mode immunity Criteria A N61000 4 8 1994 Power Frequency Magnetic Field immunity Criteria A N61000 4 11 1994 Voltage Dip and Interrupt immunity Criteria A a m m ma a a a Declaration of Conformity based on tests conducted by Chomerics Test Services Woburn MA 01801 USA in September 2001 Test records are outlined in Chomerics Test Report EMI3053 01 We hereby declare that the equipment specified conforms to the above Directives and Standards 2 Moet Carl Haapaoja Director of Quality Assurance Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton Massachusetts 02766 508 946 5100 Fax 508 946 9500 E mail info mccdag com www mccdag com2. 50 kHz Average 2 bins Average 1 bin Average bins Bipolar 5 V 100 100 3 bins Digital input output Table 2 Digital I O specifications Parameter Specification Digital type main connector Output 74ACT273 Input 74LS244 Configuration 3 fixed input 4 fixed output Number of channels 7 Output high 3 94 volts min 24 mA Vcc 4 5 V Output low 0 36 volts max 24 mA Vcc 4 5 V Input high 2 0 volts min 7 volts absolute max Input low 0 8 volts max 0 5 volts absolute min Interrupts INTA mapped to IRQn via PCI BIOS at boot time Interrupt enable Programmable through PCI controller 0 disabled 1 enabled default 4 1 PCI DASO08 User s Guide Specifications Interrupt sources External source EXT INT Polarity programmable through PCI controller 1 active high 0 active low default Counter section Table 3 Counter specifications Parameter Specification Counter type 82C54 device Configuration 3 down counters 16 bits each Counter 0 User counter 1 Source Available at user connector CTRICLK Gate Available at user connector CTRIGATE Output Available at user connector CTRIOUT Counter 1 User counter 2 Source Available at user connector CTR2CLK Gate Available at user connector CTR2GATE Output Available at user connector
3. CTR20UT Counter 2 User counter 3 or Interrupt Pacer Source Buffered PCI clock 33 MHz divided by 8 Gate Available at user connector CTR3GATE Output Available at user connector CTR30UT and may be software configured as Interrupt Pacer Clock input frequency 10 MHz max High pulse width clock input 30 ns min Low pulse width clock input 50 ns min Gate width high 50 ns min Gate width low 50 ns min Input low voltage 0 8 V max Input high voltage 2 0 V min Output low voltage 0 4 V max Output high voltage 3 0 V min Power consumption Table 4 Power consumption specifications Parameter Specification 5 V operating A D converting to FIFO 251 mA typical 436 mA max 12 V 13 mA typical 19 mA max 12 V 17 mA typical 23 mA max Environmental Table 5 Environmental specifications Parameter Specification Operating temperature range 0 to 50 C Storage temperature range 20 to 70 C Humidity 0 to 90 non condensing 4 2 PCI DASO8 User s Guide Specifications Main connector and pin out Table 6 Main connector specifications Parameter Specification Connector type 37 pin male D connector Compatible cables C37FF x cable C37FFS x cable Compatible accessory products with the C37FF x cable CIO MINI37 SCB 37 ISO RACK08 Compatible accessory products with the C37FFS x cable CIO MINI37 SCB 3
4. consent from Measurement Computing Corporation Life support devices systems are devices or systems which a are intended for surgical implantation into the body or b support or sustain life and whose failure to perform can be reasonably expected to result in injury Measurement Computing Corporation products are not designed with the components required and are not subject to the testing required to ensure a level of reliability suitable for the treatment and diagnosis of people iii Table of Contents Preface About this USer s Guide ii cci ceccccscecceccdecsedasasncccesdecdesussececesdeedeaedacnsccesiecderussinaceesdeededasasnececteardasaasinceeese v What you will learn from this user s guide sseseneeeseseesseeeessesetseesetsessteressestesestrstesteeserstsseenessesteseenteseseesesse v Conventions in this user s guide lt cc scecseccccesceesedaecccccadecdeccccecesseseedvlecsiecageieesede scev ES E E A EEEE E E Ei v Where to find more information ccccceceesseesceseeeeeeseeesceseeeseeeseceseceaecsaecaaecaaecseecaeeeaeeeaeseeeeeseseeneeeneeeasenaeenaes v Chapter 1 Introducing the PCIPDASOB i 0 icc cedecedceesacdcecesesed censesdecseduscisqersncedseesecdeccedustienecacict nsusedsansecdesseansticse 1 1 Overview PCI DAS08 features e ccs lt cccevscccectacs edicesicuceccesasdiceecesutcvscs cucsadesdeceteecdvccsdesdestsde eeisasvicessesed ana 1 1 Software features 31 22 0505 20 hors Soesek cig E A a uh dies
5. guide For more information on Text presented in a box signifies additional information and helpful hints related to the subject matter you are reading Caution Shaded caution statements present information to help you avoid injuring yourself and others damaging your hardware or losing your data lt tt gt Angle brackets that enclose numbers separated by a colon signify a range of numbers such as those assigned to registers bit settings etc bold text Bold text is used for the names of objects on the screen such as buttons text boxes and check boxes For example 1 Insert the disk or CD and click the OK button italic text Italic text is used for the names of manuals and help topic titles and to emphasize a word or phrase For example The J nstaCal installation procedure is explained in the Quick Start Guide Never touch the exposed pins or circuit connections on the board Where to find more information The following electronic documents provide information that is relevant to the operation of the PCI DAS08 MCC s Specifications PCI DASO8 the PDF version of the Specifications chapter in this guide is available on our web site at www mccdaq com pdfs PCI DAS08 pdf MCC s Quick Start Guide is available on our web site at www imecdaq com PDFmanuals DAQ Software Quick Start pdf MCC s Guide to Signal Connections is available on our web site at www mcecdag com signals signals pdf MCC s Universal Lib
6. 2 your board should now be installed and ready for use Although the board is part of the larger DAS family there is no correspondence among registers for different boards Software written at the register level for other DAS models will not function correctly with the PCI DASO8 board Programming languages Measurement Computing s Universal Library provides access to board functions from a variety of Windows programming languages If you are planning to write programs or would like to run the example programs for Visual Basic or any other language refer to the Universal Library User s Guide available on our web site at www mecdag com PDFmanuals sm ul user guide pdf Packaged application programs Many packaged application programs such as SoftWIRE and HP VEE now have drivers for your board If the package you own does not have drivers for the board please fax or e mail the package name and the revision number from the install disks We will research the package for you and advise how to obtain drivers Some application drivers are included with the Universal Library package but not with the application package If you have purchased an application package directly from the software vendor you may need to purchase our Universal Library and drivers Please contact us by phone fax or e mail Phone 508 946 5100 and follow the instructions for reaching Tech Support Fax 508 946 9500 to the attention of Tech Support
7. 7 ISO RACK08 CIO EXP 16 CIO EXP32 CIO EXP GP CIO EXP BRIDGE16 CIO EXP RTD16 Table 7 Main connector pin out Pin Signal Name Pin Signal Name 1 12V 20 12V 2 CTR1 CLK 21 CTR1 GATE 3 CTR1 OUT 22 CTR2 GATE 4 CTR2 CLK 23 CTR3 GATE 5 CTR2 OUT 24 EXT INT 6 CTR3 OUT 25 DIN1 7 DOUT1 26 DIN2 8 DOUT2 27 DIN3 9 DOUT3 28 DGND 10 DOUT4 29 5V 11 DGND 30 CH7 12 LLGND 31 CH6 13 LLGND 32 CH5 14 LLGND 33 CH4 15 LLGND 34 CH3 16 LLGND 35 CH2 17 LLGND 36 CH1 18 LLGND 37 CHO 19 10V REF 4 3 CE Declaration of Conformity Manufacturer Measurement Computing Corporation Address 10 Commerce Way Suite 1008 Norton MA 02766 USA Category Electrical equipment for measurement control and laboratory use Measurement Computing Corporation declares under sole responsibility that the product PCI DAS08 to which this declaration relates is in conformity with the relevant provisions of the following standards or other documents EU EMC Directive 89 336 EEC Electromagnetic Compatibility EN55022 1995 EN55024 1998 Emissions Group 1 Class B EN55022 1995 Radiated and Conducted emissions Immunity EN55024 N61000 4 2 1995 Electrostatic Discharge immunity Criteria A N61000 4 3 1997 Radiated Electromagnetic Field immunity Criteria A N61000 4 4 1995 Electric Fast Transient Burst immunity Criteria A N61000 4 5 1995
8. 7FFS x 2 1 PCI DAS08 User s Guide Installing the PCI DAS08 Signal termination and conditioning accessories MCC provides signal termination products for use with the PCI DASO8 Refer to the Field wiring signal termination and signal conditioning section for a complete list of compatible accessory products Unpacking the PCI DAS08 As with any electronic device you should take care while handling to avoid damage from static electricity Before removing the PCI DAS08 from its packaging ground yourself using a wrist strap or by simply touching the computer chassis or other grounded object to eliminate any stored static charge If any components are missing or damaged notify Measurement Computing Corporation immediately by phone fax or e mail Phone 508 946 5100 and follow the instructions for reaching Tech Support Fax 508 946 9500 to the attention of Tech Support Email techsupport mccdaq com Installing the software Refer to the Quick Start Guide for instructions on installing the software on the Measurement Computing Data Acquisition Software CD This booklet is available in PDF at www mccdag com PDFmanuals DAQ Software Quick Start pdf Installing the PCI DAS08 The PCI DASO8 board is completely plug and play There are no switches or jumpers to set To install your board follow the steps below Install the MCC DAQ software before you install your board The driver needed to run your b
9. CJC sensor Details on this product are available on our web site at www mccdaq com cbicatalog cbiproduct asp dept_id 126 amp pf_id 249 CIO EXP32 32 channel analog multiplexer board with on board CJC sensor and 2 Gain amps Details on this product are available on our web site at www imecdagq com cbicatalog cbiproduct asp dept_id 126 amp pf_id 250 2 4 PCI DAS08 User s Guide Installing the PCI DAS08 CIO EXP GP 8 channel expansion multiplexer board with resistance signal conditioning Details on this product are available on our web site at www mecdaq com cbicatalog cbiproduct asp dept_id 126 amp pf_id 244 CIO EXP BRIDGE16 16 channel expansion multiplexer board with Wheatstone bridge signal conditioning Details on this product are available on our web site at www mecdag com cbicatalog cbiproduct asp dept_id 126 amp pf_id 243 CIO EXP RTD16 16 channel expansion multiplexer board with RTD signal conditioning Details on this product are available on our web site at www imecdag com cbicatalog cbiproduct asp dept_id 126 amp pf_id 248 Information on signal connections General information regarding signal connection and configuration is available in the Guide to Signal Connections This document is available at http www measurementcomputing com signals signals pdf 2 5 Chapter 3 Programming and Developing Applications After following the installation instructions in Chapter
10. DC voltage is greater than 5 volts do not connect the PCI DASO8 to this signal source You are beyond the board s usable input range and will need to either adjust your grounding system or add special isolation signal conditioning to take useful measurements A ground offset voltage of more than 7 volts may damage the PCI DAS08 board and possibly your computer An offset voltage much greater than 7 volts will damage your electronics and may be hazardous to your health Field wiring signal termination and signal conditioning You can use the following MCC screw terminal boards to terminate field signals and route them into the PCI DAS08 board using the C37FF x or C37FFS x cable CIO MINI37 37 pin screw terminal board Details on this product are available at www mecdaq com cbicatalog cbiproduct asp dept_id 102 amp pf_id 255 SCB 37 37 conductor shielded signal connection screw terminal box that provides two independent 50 pin connections Details on this product are available at www imcecdagq com cbicatalog cbiproduct asp dept_id 196 amp pf_id 1166 MCC provides the following analog signal conditioning products for use with your PCI DASO08 board ISO RACKO8 Isolated 8 channel 5B module rack for analog signal conditioning and expansion Details on this product are available on our web site at www mecdaq com cbicatalog cbiproduct asp dept_id 127 amp pf_id 449 CIO EXP16 16 channel analog multiplexer board with on board
11. Email techsupport mccdaq com Register level programming You should use the Universal Library or one of the packaged application programs mentioned above to control your board Only experienced programmers should try register level programming If you need to program at the register level in your application you can find more information in the Register Map for the PCI DASO8 Series available at www mccdaq com registermaps RegMapPCI DAS08 pdf 3 1 Chapter 4 Specifications Typical for 25 C unless otherwise specified Specifications in italic text are guaranteed by design Analog input Table 1 Analog input specifications Parameter Specification A D converter type AD1674J Resolution 12 bits Ranges 5 V A D pacing Software polled A D triggering modes Digital Software polling of digital input DIN1 followed by pacer loading and configuration Data transfer Software polled Polarity Bipolar Number of channels 8 single ended A D conversion time 10 us Throughput 40 kHz typical PC dependent Relative accuracy 1 LSB Differential linearity error No missing codes guaranteed Integral linearity error 1 LSB Gain drift A D specs 180 ppm C Zero drift A D specs 60 ppm C Input leakage current 60 nA max over temperature Input impedance 10 MegOhm min Absolute maximum input voltage 35 V Noise distribution Rate 1
12. PCI DASO8 Analog Input and Digital I O User s Guide MEASUREMENT COMPUTING PCI DAS08 Analog input and Digital I O User s Guide A Ai MEASUREMENT COMPUTING Document Revision 5 June 2006 Copyright 2006 Measurement Computing Corporation Your new Measurement Computing product comes with a fantastic extra Management committed to your satisfaction Refer to www mccdag com execteam html for the names titles and contact information of each key executive at Measurement Computing Thank you for choosing a Measurement Computing product and congratulations You own the finest and you can now enjoy the protection of the most comprehensive warranties and unmatched phone tech support It s the embodiment of our two missions To offer the highest quality computer based data acquisition control and GPIB hardware and software available at the best possible price To offer our customers superior post sale support FREE Whether providing unrivaled telephone technical and sales support on our latest product offerings or continuing that same first rate support on older products and operating systems we re committed to you Lifetime warranty Every hardware product manufactured by Measurement Computing Corporation is warranted against defects in materials or workmanship for the life of the product Products found defective are repaired or replaced promptly Lifetime Harsh Environment Warranty We
13. aeeesenseeaeeneees 2 4 Chapter 3 Programming and Developing Applications ccc seeeceeeeeeeeseeeeee cess eee eeeeeeaeeeeeeeeeseeeeeeneeeeeeeeeees 3 1 Programming languages l e a a a a e e Ar E an e aie 3 1 Packaged application programs ei e E E E E E E K han se OS 3 1 Re gist er level programming ase sniin iien ck esac esce ca tev nce eeeadesut cence icucstcssdecetencdedcadesdesiidscdeuiesvitucstses vcesteedeeet 3 1 Chapter 4 SPCGCIIICATIONS fi A E vein cate dicehaete di A cnet svinctbcceaetbevevanctocneeevaveutetadesstes 4 1 Analog input eri width ne a AAG aR OR AS SOA tend okt ASA eS 4 1 Digital mputy outputccscek ceo eese hei css eee ess Boe ck ages ees ese os es 4 1 Counter sections ura Ae ei ie iitee eis ace ions leo castes sales ele Sobel oe Ns hoon EAN obs obi ata Ne oh 4 2 Power CONSUMpH onkse he ete A AR Sn we ed nts 4 2 Envir imentaken e iste Reais cca okey ie wis ee eee es eg ee eect eee es 4 2 Main connector and pitt OUt22 20c 2cc cccecvscccecevcs ediccsccesecedins iie deecsecescecervacdvecsdesdesisds deusasvicessdsecdvceetuceers 4 3 iv Preface About this User s Guide What you will learn from this user s guide This user s guide explains how to install configure and use the PCI DASO08 so that you get the most out of the analog input and digital I O features This user s guide also refers you to related documents available on our web site and to technical support resources Conventions in this user s
14. es tos lee a eR aL me aoe 1 1 PCI DASO8 block diagrami aa E ncoshsdgli ones oe ede te O E O E O es 1 2 Chapter 2 Installing the PCI DASO8 cvccecs ccceiscssce cecessceeeessseeeseuscteceeenseceeeesscteeedusdeesecenseecueesecersevsnteendvenseres enters 2 1 What comes with your shipment ccececsseescesceeeeeseesscesececesseceseceecnaeceaecaaecseecaeeeseeeaeeseeeaeeeaeeseseseeeeenaes 2 1 Hardware 5 2 tc suits aoe thy tae AS GL MN tee aN SA rete ete EA TRN cia MeN tah alt aD Additional documentation Optional components ccecceseescessceseceseeseesecesecsceeseeseceaecsseeseesecsaecseeeseeseceaecaseesesecsaecaeeeseeseceecsaecaseeseesecaaecaeeeeeeaeeaeeneees Unpacking the PCI DAS08 Installing the software wic 2 detec aeRO ee Bie ee BAR EA ee EUR ee OR ee ee UR Installing the PCIZDASO8 ves sccic Soncsantiscch ciate ftetveges e joatadoedened dos Sones e E ea tala aeeseet see Configuring the PCI DASO8 4 ccisscsevescsuee cies satesadsandt sndh vhssseeasdes agen ite lace cacesh sensuescdeas ea R hs vieuncedias obs 2 3 Connecting the board for I O operations ceccesceesseescesseeesceseeeseceseceaecsaecssecaeecaeeeseseneeeeeeeeseesseeeseeereenseenaes 2 3 Connectors cables main I O Connector cceeeceesseesceecsseeseesecesecaeeescseceaecaeeescsecsecsaecseeeecaecaaecaeeeeeaecaaecaeeeeenaeeeaeeneees 2 3 Field wiring signal termination and signal Conditioming ceccecessceesceseesseeecesecesecsecaeeeecesecsaecaeeseceseceaec
15. ing the PCI DAS08 Configuring the PCI DAS08 All hardware configuration options on the PCI DAS08 are software controlled There are no switches or jumpers to set Connecting the board for I O operations Connectors cables main I O connector Table 2 1 lists the board connectors applicable cables and compatible accessory boards Table 2 1 Board Connectors cables accessory equipment Connector type 37 pin male D connector Compatible cables C37FF x 37 pin cable x length in feet Figure 2 2 C37FFS x 37 pin shielded cable x length in feet Figure 2 3 Compatible accessory products CIO MINI37 with the C37FF x cable SCB 37 ISO RACK08 Compatible accessory products CIO MINI37 with the C37FFS x cable SCB 37 ISO RACK08 CIO EXP16 CIO EXP32 CIO EXP GP CIO EXP BRIDGE 16 CIO EXP RTD16 12V 20 1 12V CTR1 GATE 21 2 CTR1 CLK CTR2 GATE 22 3 CTR1 OUT CTR3 GATE 23 4 CTR2 CLK EXT INT 24 5 CTR2 OOUT DIN1 25 6 CTR3 OUT DIN2 26 7 DOUT1 DIN3 27 8 DOUT2 DGND 28 9 DOUT3 5V 29 10DOUT4 CH7 30 11 DGND CH6 31 12 LLGND CH5 32 13 LLGND CH4 33 14 LLGND CH3 34 15 LLGND CH2 35 16 LLGND CH1 36 17 LLGND CHO 37 18 LLGND 19 10VREF O Figure 2 1 Main connector pinout 2 3 PCI DAS08 User s Guide Installing the PCI DAS08 The red stripe identifies pin 1 37 Figure 2 2 C37FF x cable Figure 2 3 C37FFS x cable Caution If either the AC or
16. oard is installed with the MCC DAQ software Therefore you need to install the MCC DAQ software before you install your board Refer to the Quick Start Guide for instructions on installing the software 1 Turn your computer off remove the cover and insert your board into an available PCI slot 2 Close your computer and turn it on If you are using an operating system with support for plug and play such as Windows 2000 or Windows XP a dialog box pops up as the system loads indicating that new hardware has been detected If the information file for this board is not already loaded onto your PC you will be prompted for the disk containing this file The MCC DAQ software contains this file If required insert the Measurement Computing Data Acquisition Software CD and click OK 3 To test your installation and configure your board run the nstaCal utility installed in the previous section Refer to the Quick Start Guide that came with your board for information on how to initially set up and load JnstaCal If your board has been powered off for more than 10 minutes allow your computer to warm up for at least 15 minutes before acquiring data This warm up period is required for the board to achieve its rated accuracy The high speed components used on the board generate heat and it takes this amount of time for a board to reach steady state if it has been powered off for a significant amount of time 2 2 PCI DAS08 User s Guide Install
17. possibility of such damages HM PCI DAS08 doc ii Trademark and Copyright Information TracerDAQ Universal Library Harsh Environment Warranty Measurement Computing Corporation and the Measurement Computing logo are either trademarks or registered trademarks of Measurement Computing Corporation Windows Microsoft and Visual Studio are either trademarks or registered trademarks of Microsoft Corporation LabVIEW is a trademark of National Instruments CompactFlash is a registered trademark of SanDisk Corporation All other trademarks are the property of their respective owners Information furnished by Measurement Computing Corporation is believed to be accurate and reliable However no responsibility is assumed by Measurement Computing Corporation neither for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or copyrights of Measurement Computing Corporation All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form by any means electronic mechanical by photocopying recording or otherwise without the prior written permission of Measurement Computing Corporation Notice Measurement Computing Corporation does not authorize any Measurement Computing Corporation product for use in life support systems and or devices without prior written
18. rary User s Guide is available on our web site at www mecdag com PDFmanuals sm ul user guide pdf MCC s Universal Library Function Reference is available on our web site at www mecdag com PDFmanuals sm ul functions pdf a MCC s Universal Library for LabVIEW User s Guide is available on our web site at www mecdag com PDFmanuals SM UL LabVIEW pdf PCI DASO08 User s Guide this document is also available on our web site at www mcecdaq com PDFmanuals PCI DAS08 pdf Chapter 1 Introducing the PCI DAS08 Overview PCI DAS08 features This manual explains how to configure install and use your PCI DAS08 board The PCI DAS08 is a multifunction measurement and control board designed to operate in computers with PCI bus accessory slots The PCI DASO08 board provides the following features Eight single ended 12 bit analog inputs 12 bit A D resolution Sample rates of up to 40 kHz 5V input range Three 16 bit counters Seven digital I O bits three input four output Connector compatible with Measurement Computing s ISA based CIO DAS08 board The PCI DAS08 board is completely plug and play with no jumpers or switches to set All board addresses are set by the board s plug and play software Software features For information on the features of JnstaCal and the other software included with your PCI DAS08 refer to the Quick Start Guide that shipped with your device The Quick Start G
19. uide is also available in PDF at www mecdaq com PDFmanuals DAQ Software Quick Start pdf Check www mccdag com download htm for the latest software version or versions of the software supported under less commonly used operating systems PCI DAS08 User s Guide Introducing the PCI DAS08 PCI DAS08 block diagram PCI DAS08 functions are illustrated in the block diagram shown here Buffer 10 Volt lt Reference Analog In 8 CH S E AID Control Channel Select 82C54 16 bit Counters Input Clock0 Gated Output Clock0 Input Clock1 Gate1 Output Clock1 Gate2 Output Clock2 Controller FPGA and Logic ae ounter I E 5 ae Input Clock2 Input 2 0 Output 3 0 Figure 1 1 PCI DAS08 block diagram 1 2 Chapter 2 Installing the PCI DAS08 What comes with your shipment The following items are shipped with the PCI DA S08 Hardware PCI DASO08 e E PCI DAS08 Made in U S A Additional documentation In addition to this hardware user s guide you should also receive the Quick Start Guide available in PDF at www mecdag com PDFmanuals DAQ Software Quick Start pdf This booklet supplies a brief description of the software you received with your PCI DAS08 and information regarding installation of that software Please read this booklet completely before installing any software or hardware Optional components Cables C37FF x C3
20. will replace any product manufactured by Measurement Computing Corporation that is damaged even due to misuse for only 50 of the current list price I O boards face some tough operating conditions some more severe than the boards are designed to withstand When a board becomes damaged just return the unit with an order for its replacement at only 50 of the current list price We don t need to profit from your misfortune By the way we honor this warranty for any manufacturer s board that we have a replacement for 30 Day Money Back Guarantee You may return any Measurement Computing Corporation product within 30 days of purchase for a full refund of the price paid for the product being returned If you are not satisfied or chose the wrong product by mistake you do not have to keep it Please call for an RMA number first No credits or returns accepted without a copy of the original invoice Some software products are subject to a repackaging fee These warranties are in lieu of all other warranties expressed or implied including any implied warranty of merchantability or fitness for a particular application The remedies provided herein are the buyer s sole and exclusive remedies Neither Measurement Computing Corporation nor its employees shall be liable for any direct or indirect special incidental or consequential damage arising from the use of its products even if Measurement Computing Corporation has been notified in advance of the
Download Pdf Manuals
Related Search