PSE-SW5G44DNR User's Guide-V20110104
Contents
1. MSE PSE SW5G44DNR 5 Port PoE Switch amp Extender Repeat Ethernet and PoE AC DC PoE TRIPLE INPUT USER S MANUAL MSTRONIG CO LTD User s Manual MSE PSE SW5G44DNR 1 General InformatiOn rrrnnnnnnnvrnnnnnnnnunnvevnnnnnnnnennnnnnnnnnerennnnnnn 3 2 Hardware Description aaavvnnnnnnnnnnnnvnnnnnnnnnnnnvnnnnnnnnnnnnnvennn 3 Frem Panel menies i siusles 3 Reat ee RER EE 5 Ethernet Port MING 22 7 PER VINN NN 9 Network Appleatibn iruasasreenra Sea ites nade een ion eh 10 3 Technical Specification cccceccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee TT MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR 1 General Information The PoE Power Over Ethernet Switch is a AC DC PoE triple input model provides four 10M 100M 1000M TX ports with PoE PSE function plus one 10M 100M 1000M TX up link port with PoE PD function It allows power from PoE power souring equipment PSE and delivers power to PoE powered device PD which is compliant with IEEE802 3af and IEEE802 3at standard to receive and deliver both Ethernet data and DC power through the traditional UTP or STP cable The PoE Switch can extend Ethernet data and DC power up to 200 meters This manual will help you install and maintain the PoE switch Installation of the PoE switch is very easy and you will begin to operate as soon as the device is powered up 2 Hardware Description Front Panel The Front Panel of the PSE SW5G44DNR consists of 5 x RJ 45 Eth2. ernet ports 12 x LED port indicators and one ON OFF switch for AC power anna nn Figure 2 1 The front panel of PSE SW5D44DNR MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR There are 12 LEDs on the PoE switch to indicate the status of power and signal The following section describes the functions of each LED indicator POWER LED LED STATUS Description Power Green LED ON when power input DC IN on rear panel or Port 5 on front panel has valid power supplied Red The indicator is unused on PSE SWSG44DNR Off No power supplied SWITCH LED the right indicator on RJ45 LED STATUS Description P1 P5 Green A network device is detected 1000Mbps Link Act but no communication activity is detected Green This port is transmitting to or receiving Blinking package from another device at 1000Mbps Yellow A network device is detected 10Mbps or 100Mbps but no communication activity is detected Yellow This port is transmitting to or receiving Blinking package from another device at 10Mbps or 100Mbps Off No device is detected MSTRONIC CO LTD User s Manual i MSE PSE SW5G44DNR PoE LED the left indicator on RJ45 P1 P4 Yellow A valid Powered Device PD is detected PoE and delivering power on this port Off No PD is detected on this port Yellow Powered via all 4 data pairs P5 PoE Yellow Powered
3. in 4 Pin 7 Pin 5 Pin 8 Pin 7 Pin 4 Pin 8 Pin 8 Connect an Ethernet cable into any switch port and connect the other side to your attached device The Link Act LED green or yellow will light up when the cable is correctly connected Refer to the LED Indicator section for descriptions of each LED indicator If a port LED is off you should check for connectivity problems between that port and the network device connected The maximum cable length for 10 100 1000BaseT with Cat 5 twisted pair cables is typically 100m 328 ft MSTRONIC CO LTD User s Manual PD Port Wiring Port 1 to 4 provides PoE injection function with maximum 35W ability to power up the powered device using the straight through or cross over Ethernet cable The PoE switch follows the IEEE802 3af Alternative B mode connector assignment The following MSE PSE SW5G44DNR table shows pin assignment of alternative A and B for the Power Source Equipment Condado Alternative A Alternative A Alternative B MDI X MDI All 1 Negative Vport Positive Vport 2 Negative Vport Positive Vport 3 Positive Vport Negative port 4 Positive Vport 5 Positive Vport 6 Positive Vport Negativen Vport 7 Negative Vport 8 Negative Vport Be sure the twisted pair cable is bound with the standard RJ 45 pin especially the pin 4 5 7 and 8 If the RJ 45 is bound with the wrong pin number the PoE switch will not recogni
4. ir C plus V V on line 4 and 5 Data pair D plus V V on line 7 and 8 The DC terminal block on rear panel should be wired as shown below ap ap in Vin Frame Ground DC supply MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR Ethernet Port Wiring The PoE switch family supports one RJ 45 uplink port 5 with PoE PD and four RJ 45 ports port 1 4 with PoE PSE with automatic MDI MDI X crossover auto sense for the speed and duplex for 10Base T 100Base TX or 1000Base T connection Automatic MDI MDI X crossover allows you to connect to other devices switches hubs or workstations etc without regard to using straight through or crossover cabling Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs C amp D pair 4 5 and pair7 8 to the PD Port 5 provides Power Device function that receive power from 4 pairs or 2 pairs Ethernet cable The following tables describe the wiring diagram of straight through and crossover cabling The crossover cables simply cross connect the transmit lines at each end to the receive lines at the opposite end Straight through Cabling Pin I Pin I Pin 2 Pin 2 Pin 3 Pin 3 Pin 6 Pin 6 Pin 4 Pin 4 Pin 5 Pin 5 Pin 7 Pin 7 Pin 8 Pin 8 MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR Cross over Cabling Pin I Pin 3 Pin 2 Pin 6 Pin 3 Pin I Pin 6 Pin 2 P
5. uplex 1488000pps for1000base T 148800pps for 100base T 14880pps for 10base T 1K MAC address table self learning RJ 45 Port 1 4 PSE auto power management Pin assignment as below data pair A 1 2 data pair B 3 6 data pair C with V 4 5 data pair D with V 7 8 Port 5 4 pairs PD Port 1 4 IEEE802 3af 16 8W TEEE802 3at 35W Port 5 90W 802 3at 2 event classification User s Manual MSE PSE SW5G44DNR PSE disconnect mode DC disconnect PoE auto detection TEEE802 3af amp IEEE802 3at 2 event classification signaling PoE protection Over temperature over current over under voltage LEDs Link Activity Green ON Green Blinking 1000Mbps Yellow Yellow Blinking 10M 100Mbps PoE Yellow port 1 4 ON PD detect Port S UPLINK ON 4 pair power Blinking 2 pair power POWER Green normal Power input Port S UPLINK from network switch or midspan DC input 42 57 VDC AC input 90 264VAC 47 63Hz 150W max Power consumption 8W without PD loading Power efficiency 75 at full load 48V typical Operating temperature 20 C 85 C Operation humidity 90 relative humidity non condensing Storage temperature 55 C 105 C Dimension 44mm H x210mm W x199mm D 12 MSTRONIC CO LTD
6. via 2 data pairs 1 2 3 6 or 4 5 7 8 Blanking are all acceptable Off No power is detected on this port Rear Panel The AC inlet DC input terminal and 2 Ventilation fan are located at the rear panel of the PSE SW5G44DNR The device will work with AC in the range 90 264V AC 47 63Hz It will also work with DC 48V 40V 57V Clete lan carla ge es FG Vin Vint AC INPUT 90 264VAC 50 60Hz DC INPUT 40 87VDC Figure 2 1 The rear panel of PSE SW5D44DNR All of the PoE switches allow for the possibility to be powered by another PoE source 42 5 57VDC on port 5 UPLINK For PoE operation make sure your power supply offers at least 75W for 4x 802 3af PoE port or 150W for 4x 802 3at PoE port If the PSE SW5G44DNR is not powered in the above designated input voltage it will only function as an Ethernet switch without PoE output MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR If powered on DC terminal block please make sure the input current is not over 10A If powered on port 5 make sure the input current is not over 2A Ports 1 4 will deliver DC power over the Ethernet cable with the connection as Data pair A on line and 2 Data pair B on line 3 and 6 Data pair C plus V on line 4 and 5 Data pair D plus V on line 7 and 8 Port 5 may get DC power over the Ethernet cable with the connection as Data pair A plus V V on line 1 and 2 Data pair B plus V V on line 3 and 6 Data pa
7. ze the PD and won t deliver DC power to the PD The yellow PoE LED will light up when the cable is correctly connected Refer to the LED Indicator section for descriptions of each LED indicator If a port LED is off you should check for connectivity problems between that port and the network device connected MSTRONIC CO LTD User s Manual MSE PSE SW5G44DNR Network Application The PoE Switch can receive power from a PoE midspan and provide power to the PD which follows the IEEE 802 3af at standard in the network The PoE Switch can be installed in a more appropriate position for better performance to extend Ethernet to 200 meters The following figure is an example of a network application for PoE Switch PSE SW5G PoE Switch Datat Power Network Wireless LAN Network VolP Phone CAIRN Access Point Camera MSTRONIC CO LTD 10 User s Manual MSE PSE SW5G44DNR 3 Technical Specifications Standards Ports Transmission speed Switch technology Protocols Flow control Data transmission rate Address table Connect PoE port Maximum PoE power MSTRONIC CO LTD IEEE802 3 IEEE802 3u standards IEEE802 3ab 10 base T 100base TX 1000base T 5 ports with PoE 4 PSE amp 1 PD support auto crossover amp auto polarity 1000Mbps 1000base T 100 Mbps 100base TX 10 Mbps 10base T Auto negotiation Store and forward CSMA CD TEEE802 3x full duplex back pressure half d
Download Pdf Manuals
Related Search