Home

Vibrator Massage & Heat Installation Manual [8 FUNCTION & 6

image

Contents

1. Vibrator Massage amp Heat Installation Manual 8 FUNCTION amp 6 Motors Agent Akee AKEE INDUSTRIAL CO LTD Motor Placement Chair Heat Pad 23 FERRET RAE KAA Motor Cavity Cutout Template 21 4 Massage System Parts List M6 M5 Heat Pad Connect Box Fuse TO Car Battery Red Line Black Line 1 Motor set 6 pcs 4 Connect box 1 pcs 2 Controler 1 pcs 5 Heat pad 1 pcs 3 Power wire 1 pcs How To Operator The Massage Controller 1 LED Time Indicator Shows the time 15 30 2 Power Button Turns the power on and off 3 Time setting Button Press this button to select the action period of 15 30 Minutes 4 Function Button Selects any of the nine 8 programs manually 5 function Indicator Indicates whether using the autmatic or the manual mode of selec tion 6 Speed Button Controls the intensity of the massage action in all modes There are Five 5 speeds that can be selected The chair always begin at the middle intensity When the power is turned on 7 Heat switch turns the heater on and off FUNCTION AZZ ZZZE O Important Safety Instructions When using an electrical appliance basic precautions should always be Followed Including the followed Read all instructions before using this appliance DANGER To reduce the risk of electric shock 1 Always unplugs this appliance from electrical out let immedi ately after using and before cleaning 2 Do not reach for an appliance that h
2. aps as shown below Bottm Foam N N Back Foam Attach to Seat Frame Components Connect Box l Wire Harness System Power Connection Power Connection To Vehicle 1 Run the power harness under the carpet and along the scuff plate toward the fuse box 2 Install the negative wire to the OEM ground screw and secure in place 3 Connect the red wire positive to the power seat mechanism power wire Ground Connect Box Harness Extension Fuse Box Wiring Motor Installation Foam A Foam Cutout Cut out the foam to receive the shape of the motor housing by pulling back the long cut of the foam and placing the blade on an angle and cut towards the ce nter Repeat this on the other side and remove the foam cutout r 1 Cross Section Of Foam B Verify that all motors are operational before Gluing Gluing Motors Using spray gluc apply into the foam cavity and then place motor into foam cavity and gently pull the motor wires to insure a light fit Apply pressure to the top of motors and hold against the foam for 15 seconds Apply glue in these areas Do not spray glue on the motor or motor plate C Needle Punch Application The Photo below shows the final installation of the needle punch on the set bottom VZIZIZZIZZZZZZZZZZZ 1 4 Foam If Required Glue Cross Section Of Foam
3. as fallen into water Unplug immediately 3 Do not place or store appliance where it can fall or be pulled into a tub or sink 4 Do not place in or drop into water or other liquid WARNING To reduce the risk burns fire electric shock or injury to persons 1 An appliance should never be left unattended when plugged in unplug from outlet When not in use And before putting on or taking off parts 2 Do not operate under blanket or pillow excessive heating can occur cause fire electric shock or injury to persons 3 Use this appliance only for this intended use as described in this in this manual 4 Never operate this appliance if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped in to water 5 Do not carry this appliance by supply cord or use cord as a handle 6 Keep the cord away from heated surfaces 7 Never drop or insert any into this product 8 Do not use outdoors 9 To disconnect turn alt controls to the OFF position then remove plug from outlet Wiring Placement Route the wirce down the seat back and pass them to the rear of the bottom seat cover Cut an entry hole at the rear of the bottom seat cover and pass the wire harncss throuth or tuck the harness around the rear of the seat cushion Attach the contoller box to the seat frame components with tie wraps and connect all wiring and the controller wand Bundle up and organize the loose wiring with tie wr

Download Pdf Manuals

image

Related Search

Related Contents

Epson Perfection 4490 Office Scanner Warranty Statement  ProCom PCD18T Installation Guide  GP・MP 外形図  How humans factor (in medical device design)  VN-801PC - HearMore.com  Médias-ONG mode d`emploi » Rendez-vous de la  Untitled - Atlantis-Land  Coax Explorer™ Plus Tester Instruction Manual  Car amplifier Audison Thesis TH Due two  

Copyright © All rights reserved.
Failed to retrieve file