User Manual 15” Full IP65 Stainless Flat Touch Panel PC
Contents
1. e South Bridge Configures the south bridge parameters such as TPT devices PCI express root ports and power management Boot Menu The Boot menu configures boot settings Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Security Save amp Exit Setup Prompt Timeout Version 2 14 1219 Copyright C 2011 American Megatrends Inc e Bootup NumLock State Selects the keyboard NumLock state e Quiet Boot Enables or disables quite boot option e Fast Boot Enables or disables initialization of devices when booting up GateA20 Active Allows users to disable GA20 e Option ROM Messages Sets display mode for option ROM e Interrupt 19 Capture Enables trap Interrupt 19 e Boot Option Priorities Sets the system boot order of Boot Option 1 and Boot Option 2 e Hard Drive BBS Priorities Sets the order of the legacy devices Security Menu The Security menu contains the security settings such as configuring the Administrator and User Passwords Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Boot Save amp Exit Administrator Password Version 2 14 1219 Copyright C 2011 American Megatrends Inc e Administrator Password Configures the administrator password which will be required before entering the BIOS Setup Utility e User Password Configures the user password If both the administrator and user passwords are set passwo2. Timer PCI Subsystem ACPI CPU configuration Thermal configuration IDE configuration Intel Fast Flash Standby USB configuration and PPM configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Chipset Boot Security Save amp Exit Launch PXE OpROM Disabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc These advanced configurations are meant for system administrators Do not change the settings if you are unsure e Launch PXE OpROM Enables or disables boot options for legacy network devices e Watch Dog Timer Select Enables or disables watchdog timer e PCI Subsystem Settings Configures PCI PCI X and PCI Express settings e ACPI Settings Configures system ACPI parameters e CPU Configuration Configures CPU parameters e Thermal Configuration Configures thermal parameters e IDE Configuration Configures IDE parameters e Intel Fast Flash Standby Enables Intel Fast Flash Standby technology e USB Configuration Configures USB parameters e PPM Configuration Configures PPM parameters Chipset Menu The Chipset menu contains the host and south bridge settings Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Boot Security Save amp Exit gt Host Bridge Version 2 14 1219 Copyright C 2011 American Megatrends e Host Bridge Configures the host bridge parameters such as Memory Frequency and Timing and Intel IGD configurations
3. fanless 15 inch Stainless Panel PC has a footprint of 15 6 x 12 2 inches and is less than two inches thick The sturdy stainless steel housing has anti corrosion protection and carries an IP65 NEMA4 sealing rating meaning that it s completely protected against dust and also protected against low pressure water jets from all directions The very wide 4 to 140 degree Fahrenheit operating temperature range means the panel can be deployed almost anywhere This device is suitable for deployment in certain hazardous locations where flammable substance may be present Specifically the device is certified for use in Class 1 Division 2 Groups A through D i e Acetylene Hydrogen Ethylene and Propane classified areas and surface temperatures not exceeding 275 Fahrenheit 135 Celsius in the US market and ATEX Gas Zone 2 Classified areas in European and other markets Physical Overview Package Contents Before using this Panel PC please make sure that all the items listed below are present in your package USB adapter USB Type A to Type B Ethernet Cable User s Manual and Quick Start guide Recovery DVD and touch driver CD Power Cord 9 Ethernet extension RS 232 Cable adapter VESA Mounting Screws Product Overview Front View Touch Display VESA mounting Holek a Side and Rear Views io ko VESA mounting holes T O
4. from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall could cause damage The openings on the enclosure are for air convection and to protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons only qualified service personnel should open the equipment If any of the following situations arises get the equipment checked by service personnel o The power cord or plug is damaged o Liquid has penetrated into the equipment o The equipment has been exposed to moisture o The equipment does not work well or you cannot get it to work according to the user s manual o The equipment has been dropped and damaged o The equipment has obvious sign
5. may be present This device is typically used for automation or control purposes Important Information Federal Communications Commission Radio Frequency Interface Statement For USA This device complies with part 15 FCC rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at him own expense Certifications and Standards Certification with ATEX Directive 94 9 EC Independent 3rd party assessment Notified Body DEMKO Self Declaration in accordance with European LVD Directive 2006 95 EC Independent 3rd party assessment Accredited by IEC 17025 Self Declaration in accordance with EMC Directive 4 2004 108 EC Independe
6. E F Xobre p 1 Q vom 7 When the screen is touched the conductive coating makes electrical contact with the coating on the glass The voltages produced are the analog representation of the position touched The controller digitizes these voltages and transmits them to the computer for processing The five wire technology utilizes the bottom substrate for both X and Y axis measurements The flexible coversheet acts only as a voltage measuring probe This means the touchscreen will continue working properly even with non uniformity in the cover sheet s conductive coating The result is an accurate durable and reliable touchscreen that offers drift free operation The touchscreens are sealed against contamination and moisture The coversheet is sealed to the glass substrate with an industrial grade caulk This prevents wicking of fluid between the coversheet and glass Also the touchscreens are not air vented thereby preventing fluid ingress through an air vent Brief Specifications Subject Details Input Method Finger gloved hand or stylus activation Positional Accuracy Standard deviation error is less than 0 080 2 mm Touch Activation Force Typically less than 4 ounces 113 grams Touch point density is based on controller resolution of 4096 Resolution X 4096 HL products 80 5 at 550 nm wavelength Enhanced Light Transmission products 60 5 at 550 nm wavelength Update touch screen driver or new information Go t
7. SB button GNOD ra DC IN 12V DC in Jack LED Indicators Ethernet Port O09000 gt D AUTO MENU LED Type Status Description Power is on Power b Off Power is off Blinking Storage activity data is being read or written Storage C Off System is idle Hardware Specification ie Intel Dual Core Atom N2600 1 6GHz processor S Windows 7 embedded systems System Chipset Intel NM10 Bios AMI 16Mbit Flash System Memory 4GB capacity 2GB pre installed USB 2 x USB 2 0 Storage Giopsoe Tunno Removable 32GB industrial grade SSD to store OS p ne support up to 256GB e Horizontal 160 degree left to right e Vertical 140 degree up to down outdoors around heavy equipment Power Requirements Input Voltage Typical 12V DC isolation 800V View Angles Mechanical Dimensions 15 Dimensions System Mounting to a Sub Frame or Panel Panel Mount Note that customer needs to provide their own opening enclosure To mount the device to the enclosure do the following 1 Prepare the cut out following this dimension 2 Prepare the IP54 rubber available as standard accessories 3 Place the unit in front of the enclosure and place the rubber around the perimeter as shown in the picture below f 4 ra Fat Se CA IA A OM MOBS i ni From Front View From Rear View Red line represents IP54 rubber 4 Screw from the back through the opening and mount th
8. User Manual 15 Full P65 Stainless Flat Touch Panel PC V1 1 Wlinm are Table of Contents SUP ION CNEL Ihc cop te E A A ENE va E eso ga nega cue A sion cea aus EE E O 3 OO IIO ACI OM aa E A O 4 OVC SOV CY pa cceccecencmtecetceeeene EEOAE E AEA E E AE POA 6 PAV ere BO V EIV O a aE E E E E ET TEA 7 PACK SSC I a A E 7 Prod OVET VIO W erena E E 8 POI A A E ne rec net E E E A T E E 8 de ana rE VIEWS een E este cenrentsas secbaats itseelreeinaa seston aan pe tuacereutdinnseacuersautaranter 8 LED NCC lil OMS iai aE E E E E E E 8 Hardware SC IU EO Muassasa d 9 Mechanical DIMENSIONS seira a S 10 MS DIEN ONS eaa T E AE T 10 System Mounting to a Sub Frame or Panel cccccsecsseessesssssessssnsssnseeaeeasesaecsaeceeceaeeeeeeeeeeeeeeeeseeeeeeseseeeeseeenes 11 Panel MOUN eerror E E E E E E I AE 11 VE AVIOU sr ere ee ENE T TEE E E tere TE E TOTEE TTE 12 Gene T a R A E 12 T m 0N tHE dEVCE oerrinne a EA A EAE E eee 12 Adjusting the LCD Display Brightness eseeeseeeseeeereeererereecrreerreerressressesesssssssssssesssesseesseesreeereeerererseerreerees 13 Calibrating TOUcM Scree Gieure ae ee 13 WAS Cel ATOM E eee E E EE E E 16 Wiring Requirements esssicicsrssrcsrcsrsseisissesiicrrnererrsdsresscdrrisr intriti senter ertt an dma each annie onsen EENE EE SEENE SoTa 16 Connecting the INTE CE annaa E I VA E N AEE E E E 17 Connecting to Other DEVICES sosscccccsacccasessaniaabosianncspatisngneaicadaanaasdacanauensvondersutuasseaeadasesie
9. around and make selections in the BIOS Setup Utility 1 Before turning on the Tablet Computer connect the USB keyboard to the USB port of the Tablet Computer 2 Power on the Tablet Computer 3 When the system starts up and the post screen logo appears quickly press F2 or the Delete key to enter the BIOS Setup Utility How to Use NOTE e The BIOS Setup Utility screens shown in this chapter are for reference only The actual items or settings on your Tablet Computer may differ e The settings you select in your operating system might override similar settings in BIOS Setup Utility Key Function lt gt Selects a menu title A V Selects an item or option Brings up the submenu if available e When an item is selected opens or closes the options window e Goes to the next field when an item has multiple fields such as System Date BIOS Menu Main Menu The Main menu contains system information language date and time settings and the access level Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Chipset Boot Security Save amp Exit gt Intel RC Version Version 2 14 1219 Copyright C 2011 American Megatrends Inc e Intel RC Version Displays Intel reference code version e System Language Sets the system language e System Date Sets the system date e System Time Sets the system time Advanced Menu The Advanced menu contains advanced settings such as Watch Dog
10. de Sets the boot override option Maintenance Regular Cleaning and Maintenance Before Cleaning Make sure the device is turned off Disconnect the power cable from any AC outlet When Cleaning Never spray or pour any liquid directly on the screen or case Wipe the screen with a clean soft lint free cloth This remove dust and other particles The display area is highly susceptible to scratching Do not use Ketone type material ex Acetone Ethyl alcohol toluene ethyl acid or methyl chloride to clear the panel It may permanently damage the panel and void the warranty If it is still not clean enough apply a small amount of non ammonia non alcohol based glass cleaner onto a clean soft lint free cloth and wipe the screen Do Not use water or oil directly on the display screen If droplets are allowed to drop on the screen permanent staining or discoloration may occur Using Recovery Wizard to Restore Panel PC Our system has a dedicated recovery partition stored on the hard drive of the PC to enable quick one key recovery process This partition occupies about 11GB of the storage space and comes built in to each Panel PC and Box PC Warning Before starting the recovery process be sure to backup all user data as all data will be lost after the recovery process To enable quick one key recovery procedure e Plug in the AC adapter to Panel PC Make sure the Panel PC stays plugged in to power source during the r
11. e unit make sure that the rubber in the right position to give IP protection VESA Mount e Dimensions 75 x 75mm Screw Hole Diameter M4 x5 mm e Direction Compatible with swimming arms mounting kits Getting Started Turning on the device 1 Remove the protective cap of the DC IN Jack 2 Plug the AC adapter to the DC in jack of your device Make sure the cable fits to the connector then tighten the O ring by turning it clockwise to secure the connection 3 Connect the AC adapter to the power cord 4 Plug the power cord to an electrical outlet 5 Plug the Power button to turn on the device SS Note e When the system hangs press the Reset button to restart the device Adjusting the LCD Display Brightness 1 Tap the arrow on the system tray to display the hidden icons 2 Double tap the Eicon to display the brightness menu 11 55 AM 2 20 2014 Calibrating Touch Screen When turning on the Panel PC for the first time it is highly recommended to calibrate the touch screen to ensure touch accu racy Five wire resistive touch screen The five wire resistive touch screens use a glass panel with a uniform resistive coating A thick polyester coversheet is tightly suspended over the top of the glass separated by small transparent insulating dots The coversheet has a hard durable coating on the outer side and a conductive coating on the inner side 4 Volts W at P D f 9
12. ecovery process e Turn on the Panel PC and when the boot screen shows up press the F6 to initiate the Recovery Wizard e The following screen shows the Recovery Wizard Click on Recovery button to continue Recovery Wizard Click Recovery to restore your system The process will dear all of your data If you do not want to restore your system please press Quit to reboot Recovery e A warning message about data loss will show up Make sure data is backed up before recovery and click on Yes to continue e Wait till the recovery process to complete During the recovery process a command prompt will show up to indicate the percent of recovery process After recovery is completed the panel computer will restart automatically oe Recovery Wizard A indos ater Fy ced aus Claaning rt cucceeehuilly conserced the os lected disk to GPT format art succended in creating the specified part itien oonp lobed Part successfully formatted the wa lame wotaaf illy assigned the drive letter or asunt point smccended in creating che specified partition aceoded in creating the specified part it low ant canpleated fcesaFally formatted the us lemme cup eteially ann igrat the drive letter or apent point ciccneded in creating the specified partition eet ponp let el
13. nt 3rd party assessment Accredited by IEC 17025 Copyright Notice No part of this document may be reproduced copied translated or transmitted in any form or by any means electronic or mechanical for any purpose without the prior written permission of the original manufacturer Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners Disclaimer We reserves the right to make changes without notice to any product including circuits and or software described or contained in this manual in order to improve design and or performance We assume no responsibility or liability for the use of the described product s conveys no license or title under any patent copyright or masks work rights to these products and makes no representations or warranties that these products are free from patent copyright or mask work right infringement unless otherwise specified Applications that are described in this manual are for illustration purposes only We make no representation or guarantee that such application will be suitable for the specified use without further testing or modification Warranty Our warranty guarantees that each of its products will be free from material and workmanship defects for a period of one year from the invoice date If the customer discovers a defect we will at his her option repair or replace the defective product at no charge to the customer p
14. o www elotouch com Elo Touch Correction Winmate Elo Touch driver software provides a consistent software interface among all ELO touch screens and controllers Go to http www elotouch com Support dnid asp for a complete list of available supports After the driver installation is complete do the following to perform touch screen calibration 1 Tap the arrow on the system tray to display the hidden icons 2 Double tap the alo icon to display the Elo Touchscreen menu EF wi Customize 11 55 AM 2 20 2014 Video alignment enables the computer to convert touchscreen coordinates into image coordinates Align the touchscreen whenever you Initially install the touchscreen drivers Change the touchmoniter or touchscreen hardware Motice the cursor isn t lined up with your finger Videu shurment enables the computer to convert touchscreen coordinates rito image coordnates Initolly install the touchsercen drivers Change the touchmonitor or touchscreen Shak Notice the cursor isn t ined up with your finger 5 Tap the Vicon if the cursor follows your finger to finish and exit the calibration utility Change the tnuchmonitor or touchscreen Note the cursor isn t ined up with your finger Installation Wiring Requirements The following common safety precautions should be observed before installing any electronic device a Strive to use separate non intersecting paths to rou
15. rd entry is required when accessing the BIOS Setup Utility The entered password determines the type of access If you enter the user password the type of access is limited to viewing the settings and basic setup configuration only If only the user password is set password entry is required before booting into Windows e HDD Security Configuration Displays the HDD security status Save amp Exit Menu The Save amp Exit menu displays ways of exiting BIOS Setup Utility After modifying the settings you must save and exit for the changes to take effect Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Boot Security Save Changes and Exit Version 2 14 1219 Copyright C 2011 American Megatrends Inc e Save Changes and Exit Saves the changes you have made and exits BIOS Setup Utility to boot into Windows directly e Discard Changes and Exit Exits BIOS Setup Utility without saving the changes you have made e Save Changes and Reset Saves the changes then restarts the system e Discard Changes and Reset Restarts the system without saving the changes you have made e Save Changes Saves changes e Discard Changes Discards all changes that you have made e Restore Defaults Restores the default factory values of all settings e Save as User Defaults Saves the changes that you have made as user defaults e Restore User Defaults Restores the user default values of all settings e Boot Overri
16. rovide it is returned during the warranty period of one year with transportation charges prepaid The returned product must be properly packaged in its original packaging to obtain warranty service If the serial number and the product shipping data differ by over 30 days the in warranty service will be made according to the shipping date In the serial numbers the third and fourth two digits give the year of manufacture and the fifth digit means the month e g with A for October B for November and C for December For example the serial number 1W14Axxxxxxxx means October of year 2014 Customer Service We provide a service guide for any problem by the following steps First visit the website of our distributor to find the update information about the product Second contact with your distributor sales representative or our customer service center for technical support if you need additional assistance You may need the following information ready before you call e Product serial number e Peripheral attachments e Software OS version application software etc e Description of complete problem e The exact wording of any error messages In addition free technical support is available from our engineers every business day We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products Please do not hesitate to call or e mail us Device Overview The
17. s of breakage e Do not leave this equipment in an uncontrolled environment where the storage temperature is below 20 C 4 F or above 50 C 122 F It may damage the equipment e CAUTION Use the recommended mounting apparatus to avoid risk of injury e WARNING Only use the connection cords that come with the product When in doubt please contact the manufacturer e WARNING Ground against electrostatic damage to the device by taking the following preventive steps o Cover workstations with approved anti static material Use a wrist strap connected to a work surface and properly grounded tools and equipment Use anti static mats heel straps or air ionizer for added protection Handle electrostatic sensitive components PCB s and assemblies by the case or the edge of the board o Avoid contact with pins leads or circuitry o Turn off power and input signals before inserting and removing connectors or test equipment Keep the work area free of non conductive materials such as ordinary plastic assembly aids and Styrofoam Use filed service tools such as cutters screwdrivers and vacuum cleaners that are conductive o Always lay drivers and PCB s with the component side down on anti static foam Intended Use 15 Full IP65 Stainless flat touch series are primarily intended for use in Hazardous areas They are suitable for use in oil gas and petrochemical manufacturing and others where ignitable gases or vapor
18. stavbsnensaotarteriescdsnananads 18 Connector Pin Assignments sds sccascosceaectcetondeaciatgeinaduannsenssasnaneasapesonesauaanesncoqcaeatenanecenarconacseneansatooenennsanaecesauenes 19 BIOS SEEI anria E E E E EE 21 ada ONS E E T E teeters A E E EE pete E E E A A E E E E E 21 Starting BIOS Setup Utility mainiininaeiieiiirnininiennei inia EE a e Eei 21 MOWN TOSE irn E A E E OEEO A E T OE E E ATO 21 BIOS O aa E NE E E E E AEEA T A A E AA E 22 Wella clare eae ne nen ener eee eee ee ee ee ee er re 28 Using Recovery Wizard to Restore Panel PC uuu eesssssssssesseceeceecceccesccecsecseseauseeseeeseeseeeseeseceeeeeseeseeeeeeeeaeas 28 Safety Information Warning Always completely disconnect the power cord from your chassis whenever you work with the hardware Do not make connections while the power is on Sensitive electronic components can be damaged by sudden power surges Only experienced electronics personnel should open the PC chassis Caution Always ground yourself to remove any static charge before touching the CPU card t Modern electronic devices are very sensitive to static electric charges As a safety precaution use a grounding wrist strap at all times Place all electronic components in a static dissipative surface or static shielded bag when they are not in the chassis Safety Precautions Please read these safety instructions carefully Please keep this user s manual for later reference Please disconnect this equipment
19. te power and networking wires If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point s Keep the wires separated according to interface The rule of thumb is that wiring that shares similar electrical characteristics may be bundled together e Do not bundle input wiring with output wiring Keep them separate When necessary it is strongly advised that you label wiring to all devices in the system N arenon e Do not run signal or communication wiring and power wiring in the same conduit To avoid interference wires with different signal characteristics i e different interfaces should be routed separately Be sure to disconnect the power cord before installing and or wiring your device e Verify the maximum possible current for each wire gauge especially for the power cords Observe all electrical codes dictating the maximum current allowable for each wire gauge e ifthe current goes above the maximum ratings 80 W the wiring could overheat causing serious damage to your equipment e Be careful when handling the unit When the unit is plugged in the internal components generate a lot of heat which may leave the outer casing too hot to touch Connecting the interface This Panel PC comes with various interfaces located on the bottom panel All of these connectors have been shipped with protective caps and tethers If you wish to detach the tethers the scre
20. ws securing them to the bottom panel will need to be removed To ensure the waterproof function can work properly make sure that the protective caps and the tethers have been securely fastened whenever the connectors are not used N mrorranr Please note that when reinstalling the protective cap it must be fully tightened to ensure the unit is properly sealed to meet the IP65 enclosure rating Connecting to Other Devices Perform the connections as shown below PANEL PC gas HAZARDOUS AREA Power adapter amp power cord Connector Pin Assignments This Display is equipped with four connectors which are IP65 level and fool proofing design Use only the cables that are included in the package The pin assignments of the cables are as follows USB Cable Finno Symbols Color ous owe owe owe RS 232 Cable CN2 1 DCD CON2 CN2 2 DSR CON2 aaa ocon Red enas ocon sue Ethernet LAN Cable inte Color ma f e oo CN2 7 White Brown Power Adapter BIOS Setup Utility When to Use You need to run BIOS Setup utility when e You see an error message on the screen requesting that you run BIOS Setup utility e You want to restore the factory default BIOS settings e You want to modify some specific hardware settings e You want to modify some specific settings to optimize the system performance Starting BIOS Setup Utility A USB keyboard is required to access move
Download Pdf Manuals
Related Search