OPERATORS MANUAL & WARRANTY FORM
Contents
1. g__GREASING amp MAINTENANCE Grease bearings universals and ensure PTO shaft has been Instruct customer how to re grease the implement Explain to the operator the requirements and repercussions of regular maintenance o2 CLUTCH ADJUSTMENT Check that clutch has been correctly fitted and nuts are tight Check the clutch has been adjusted for the customer s situation Instruct customer that an annual service is required 5 IMPLEMENT DRIVESHAFT amp TRACTOR COMPATIBILITY Check implement and PTO compatibility ensuring the PTO will not foul on the tractor or implement during linkage operation If PTO was cut make sure that it was re greased and all spring activated locking pins on the PTO Shaft move Bech IMPLEMEMNT amp TRACTOR COMPATIBILITY Check implement and Tractor compatibility Ensure thata minimum 20 of tractor and equipment weight is on the tractor s front wheels with implement in transport position OPERATION PROCEDURES I Instruct the operator on correct procedures and techniques for the type of work they have indicated they intend to carry out General safe operating procedures can be found in the Operators Manual Advise customer to carry out a risk assessment and hazard identification of the property and alert the customer to the type of potential dangers they should be looking to avoid a DANGERS Instruct customer on the potential dangers of operating the implement Outline the dangers associated with rotating bl2. horizontal hole in the web of the tooth holder Insert rubber So L O lt through here Centralize the rubber in the holder and push the new tooth against the rubber to hold it in position Top profile Dive the tooth into place using a Soft when rubber hammer ora piece of hardwood D notusea inserted standard hammer axe or any other metal tools Problem Auger will not Dig Post Hole Digger sways side to side Bent auger flighting or bent auger Auger screwing itself into the ground Excessive vibration The rubber will fold back and compress between tooth and holder locking the tooth firmly into position TROUBLE SHOOTING Possible Causes amp Solution Clutch Slipping Adjust clutch Teeth dull Sharpen or replace Ground too dry and hard Apply water or wait for rain Auger turning too fast and bouncing reduce speed Tall grass wrapping around auger remove Auger encountering rock root or other obstruction lift auger and inspect No sway bars or sway blocks on tractor have fitted by a dealer Lift arms not adjusted evenly adjust lift arms Excessive looseness in the 3 point linkage hitch use proper size pins Tractor moved while the auger was in a hole always set tractors brakes and make sure the tractor is out of gear Operator moved tractor with the auger still in a hole to try and straighten the hole that was being dug on
3. Oil not changed per instructions Friction clutch was not correctly adjusted Bent output shaft is due to operator moving tractor while auger is in a hole Gearbox overheating Low on lubricant oil fill to correct level Improper type of lubricant replace with correct lubricant Tractor stalls Auger is encountering rock roots or other foreign object remove object or change hole location Tractor idle is not set correctly tune tractor engine M e Keep hands feet hair and clothing away from equipment while engine is running Stay clear of all moving parts e During routine checks repairs and when performing adjustments keep all persons away from operators control area ensuring that no one can switch on the tractor or Implement Keep the key to the tractor in your pocket Make sure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and are firmly seated in the tractor PTO splined angular groove e When connecting the tractor to the implement always find somewhere level or flat e Always adjust the tractor lower linkage arms anti sway devices to prevent implement from swing from side to side during transport and operation Failure to do so may result in serious injury or damage Damage like bent and twisted implement towers are consumable items and are NOT covered by warranty M H RANGE ASSEMBLY INSTRUCTIONS Assembly of this implement is the r
4. tines have been properly installed Show customer how to make adjustments Describe the options available for the implement and explain there purpose and how they work o Ensure the stability of the tractor has not been compromised with the implement the customer has purchased Remember a minimum 20 of tractor and equipment gross weight must be on the tractor s front wheels with implement in the transport position If you are adding weight to the tractor to attain the 20 you must not exceed the ROPS max ballasted mass certificate Weight the tractor and implement Do not estimate o Give Operators Manual to the customer and recommend that customer become familiar with all sections especially the safety and safe operating procedures o Explain to the customer that when transporting the implement on roads or highways day or night safety devices should be used to provide adequate waming to operators of other vehicles Also explain the operator must ensure that the tractor and implement complies with current State and Federal laws and must strictly adhere to all road traffic regulations in force in his her particular state o Check PTO series is correct and that the PTO is the correct length post hole diggers only o Check gearbox is properly serviced and seals are in good condition and not leaking post hole diggers only AA IMPORTANT Gearbox was not filled with oil at the factory It must be serviced before implement is operated Fai
5. x 6 Spline Input Shaft 12 Front Cap suit Diop Spline Input Shaft 75hp Gearbox Housing 60 40 10 Nodular Shafts UNS G10450 Gears UNS G51200 Seals Triple Lipped Spring Loaded Bearings Tapered Roller Oil EP 90 2 54L Weight 50 5 kg Rotation ba 1 Input Shaft 2 Outer Cap 3 Pinion Support Housing 4 Input Seal 5 Outer Pinion Cup amp Cone 6 Inner Pinion Cup amp Cone 7 Shim Gaskets 8 Top Cover 9 Cup amp Cone Bearings 2 req 10 Output Gear 11 Output Shaft 12 Main Housing 13 Top Shim Gasket 14 Output Seal FARM EQUIPMENT Agricultural Machinery Product OHS Compliance Form We Gavhall Pty Ltd tas Kanga Farm Equipment Of 16 Cahill Street Dandenong Victoria Australia 3175 Telephone 03 9706 5166 Fax 03 9706 5050 Confirm that the following machine s Kanga Mini Range Post Hole Digger s Complete with 6 9 or 12 Auger Kanga H Range Post Hole Digger s Complete with any auger from 6 24 have had a hazard identification risk assessment and risk control procedure carried out on a representative model of the aforementioned product s in accordance with the Occupational Health and Safety requirements of all states and territories of Australia and where found necessary the appropriate risk control measures have been incorporated in the product specifications The Operators Manual contains the necessary Health and Safety information and safety warnings dec
6. Gearbox 150mm 6 75hp Gearbox 200mm 8 of Clutch linings 2 Max Auger Size 24 610mm AUGERS Length d dee Se Seenen Flighting Thickness 5mm Pilot tip Heat Treated Cast Steel replaceable Tooth Nickel Alloy Steel hardened replaceable Sizes Available 2 cee cee cee cee cee cee eee cee ee eee eee 4 100mm 13 5kg 6 150mm 14 5kg 9 228mm 19 5kg 12 305mm 24 5kg 15 380mm 27 2kg 18 457mm 34 5kg 24 610mm 60 5kg NT Mini Range Post Hole Digger are limited an a maximum auger size of 305mm 12 Augers larger than 12 305mm should not be attached to a Mini Range Post Hole Digger as they may cause the 35hp gearbox to fail In the circumstance where a larger auger has been attached to a Mini Range Post Hole Digger and a failure occurs itis likely that the gearbox will not be covered by warranty Specifications for this Gearbox can be found on page 26 of this Operators Manual Specifications for this Gearbox can be found on page 26 of this Operators Manual FARM EQUIPMENT SAFETY RULES amp ACCCIDENT PREVENTION A ATTENTION BE CAREFUL YOUR SAFETY IS INVOLVED A Safety is a primary concern in the design and manufacture of our products Unfortunately our efforts to provide safe equipment can be wiped out by a single careless act of an operator In addition to the design and configuration of equipment hazard control and accident prevent
7. PTO disengaged The auger point should be approximately 100mm back of the centre of the gearbox As the auger works down into the ground it will straighten due to the pivoting action of the boom in a downward motion If the auger has side tilt correct with the tractor s 3 point linkage NOTE If the auger tilts too far forward or to the rear it maybe necessary to move the tractor slightly Move tractor slowly and carefully so you do not bend the auger 6 With auger point lowered to the ground set the engine speed to idle and then engage PTO Make sure auger point is on the ground before engaging the PTO A IMPORTANT Under no circumstances should the PTO be run at 540 rpm No faster than half throttle in 540 rpm range VES FARM EQUIPMENT 7 As the auger penetrates the ground lower the unit slowly with the tractor s 3 point linkage arms DO NOT LET THE AUGER SCREW ITSELF INTO THE GROUND The auger must be able to dig up the ground and carry it to the top by the auger flighting 8 Dig the hole in small steps Dig down only 100 150mm then raise the auger up to allow the soil to clear Repeat this procedure until the desire depth is reached This gives you better control of the auger and prevents difficulties that could lead to an accident A IMPORTAN e Be careful when raising the auger If you raise the auger as high as the 3 point linkage arms will allow you can put the PTO shaft universal joints at an extreme angle and c
8. Pressure Plate ji 6 Spring 8 required o Setting the Clutch The slip clutch is designed to slip protecting the gearbox PTO shaft and tractor in the event of the implement striking an obstruction All new clutches supplied with Kanga Farm Equipment implements have been pre set by the following guide 1 Compress springs fully then back off two 2 tums 2 Fine tune so that the clutch slips occasionally On 20 spline models clutch retaining clamp bolts must be tightened to 150 fi Ibs to clamp clutch to shaft LOOSE BOLTS STRIPPED SPLINES NT Discs are approximately 3 2mm thick when new Replace discs after 1 6mm of wear Minimum disc thickness is 1 6mm A new slip clutch or one that has been in storage for some time may be seized Annually release springs completely and allow clutch to slip to polish pressure plate To do this you will have to carry out the following operations 1 Make sure tractor is tumed off and key is removed Remove PTO Shaft from the tractor Loosen the bolts to remove all tension from the springs Wedge the blade beam so that it cannot rotate Grab PTO Shaft or clutch input shaft and turn to make sure clutch slips If clutch does not slip freely disassemble and clean the face of the clutch pressure plates and spline base assembly Reassemble clutch Tighten each bolt evenly until the springs are compressed then back off all nuts two 2 full tums If clutch continues to slip then tighten each bol
9. an angle Auger is encountering rocks root or other obstruction remove object from hole or change location Operator did not ease the auger into the ground using the 3 point linkage Faulty hydraulic 3 point linkage system on the tractor Tractor is too small to handle this digger PTO Shaft universal cross is wom replace FARM EQUIPMENT Auger digs only so far PTO shaft bottoms out not allowing the digger to lower check range of then will not dig deeper movement Remove auger from digger and lower the digger If gearbox does not lower to the ground then PTO shaft make need to be shortened PTO Shaft interferes with drawbar swing out of the way or remove Faulty hydraulic 3 point linkage system on the tractor consult dealer Soil could have a hardpan layer 150 200mm below surface consult dealer for alternative digging methods like hydraulic down pressure diggers PTO drive shaft failure Operator raising post hole digger too high when PTO is engaged causes excessive PTO universal joint operating angle leading to a failure PTO is engaged while moving between holes Auger swings which causes excessive PTO universal joint wear which leads to a failure PTO Shaft has not been properly lubricated Engaging tractor PTO with engine at high rpm Digging holes too deep to that PTO Shaft come in contact with the ground Operating at high rpm Gearbox failure No oil in gearbox
10. and that all operators read the manual carefully and become acquainted with the adjustments and operating procedures before attempting to operate Keep a record of the risk assessment and that the operator has read and understands the correct operating procedures as outlined in this manual The implement you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use Like all mechanical products it will require routine cleaning upkeep and maintenance Lubricate the implement as specified Observe all safety information in this manual and safety decals on the implement Throughout this manual the term IMPORTANT is used to indicate that a failure to observe can cause damage to the equipment The terms CAUTION WARNING and DANGER are used in conjunction with the Safety Alert Symbol triangle with an exclamation mark to indicate the degree of risk to your personal safety YOUR SAFETY IS INVOLVED N G ER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury T This Safety Alert Symbol indicates a hazard and means ATTENTION BE CAREFUL WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices GENERAL IN
11. e Check that all hardware is tight and properly installed e Stop implement then tractor immediately upon striking an obstruction Turn off engine remove key inspect and repair any damage before resuming operations e A minimum 20 of tractor and equipment weight must be on the tractor s front wheels with implement in the transport position Without this weight tractor could tip over causing personal injury or death The weight maybe attained with a loader front wheel weights and ballast in the tyres or front tractor weights When attaining the minimum 20 weight on the front wheels you must not exceed the ROPS max ballasted mass certificate Weight the tractor and implement Do not estimate A IMPORTANT e Never exceed the recommended auger capacity of the Post Hole Digger The Mini Range is designed for use with augers up to 305mm 12 The H Range is designed for augers up to 610mm 24 Use of an incorrect auger can cause equipment damage loss of operator control and personal injury PREPARATION Before commencing operation thoroughly read and understand your Operator s Manual Contact local utility companies to make certain there are no buried gas lines electricity cables ete in the area you will be operating Then clear area of objects that could wrap around the auger or could be thrown by the auger Check for ditches stumps holes or other obstacles that could cause the tractor to roll To dig properly your tractor mus
12. it is highly recommend that before use the following is carried out 1 Drain and change the oil in the gearbox and refill to the correct level 2 Check and replace where necessary pilots teeth nuts and bolts 3 Clean machine and remove any rust that may have appeared 4 Replace any safety decals that may be damaged or painted over 5 Make sure PTO shaft and universals are moving freely and are well greased Ensure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and can sit securely in the tractor PTO splined angular groove 6 Ensure all shielding is in place and not damaged If damaged order new shielding Gearbox specifications and information regarding the quantity of oil required to fill them can be found on page 23 amp 24 of this manual FARM EQUIPMENT REPLACING PILOT amp TEETH Kanga Farm Equipment use Pengo cutting heads pilots and teeth on all agricultural augers The pilot is replaceable and held in position with a high tensile bolt and nut The bolt for a 6 Auger is Dien Ui For all other augers the bolt and nut required measures Dien 1 The teeth are retained securely in position using the Pengo Ribbed Rub r Lok method Cut the rubber to the same width as the tooth Cut rubber to Before inserting the rubber moisten with water the same width Do not use oil as the tooth Insert the cut moist piece of rubber through the
13. outline in Owner Service section of this manual Ensure tractor PTO and transmissions are in neutral before starting engine Inspect area that you will be operating in and remove any object that may cause injury or damage OWNER SERVICE Safety is a primary concern in the design and manufacture of our products Unfortunately our efforts to provide safe equipment can be wiped out by a single careless act of an operator In addition to the design and configuration of equipment hazard control and accident prevention are dependent upon the awareness concem prudence and proper training of personnel involved in the operation transport maintenance and storage of equipment It has been said The best safety device is an informed careful operator We ask you to be that kind of operator The information in this section is written for operators who possess basic mechanical skills Should you need help your dealer has trained service technicians available For your protection read and follow safety information in this manual Disengaged tractor PTO and wait for all moving parts to come to a complete stop Lower implement to the ground or block with secure robust support Turn tractor engine off remove key and disconnect PTO Shaft from the tractor before performing any service or maintenance Keep all persons away from operator control area while performing adjustments service or maintenance Never go underneath implements that a
14. 11 14 Operating Technique 12 14 Daily Operators Checklist 15 Owner Servicing 15 17 Replacing Teeth amp Pilot 17 Trouble Shooting 17 18 Assembly Instructions 18 20 Power Take Off Shaft PTO 21 23 Clutch eee 24 Gearbox Information 25 26 OH amp S Compliance Certification 27 Box Scrapers 28 Specifications 29 Safety Rules 30 31 Safety Decals 31 Operation Daily Operators Checklist 34 Maintenance 34 Assembly Instructions 35 OH amp S Compliance Certification Seege SEI Carryalls Jib Crane and Bale Handling Equipment 37 Specifications Safety Decals Safety Rules Operation Maintenance Assembly Instructions 45 Daily Operators Checklist 45 OH amp S Compliance Certification 46 Cultivators Eurotiller S Tine Chisel Plough 47 Specifications Safety Rules Safety Decals Operation Daily Operators Checklist 53 Maintenance 2 02 s e 54 Assembly Instructions 54 OH amp S Compliance Certification 55 ann FARM EQUIPMENT Pallet Forks 56 Specifications D Safety Rules Safety Decals Operation Daily Operators Checklist 62 Maintenance 63 Assembly Instructions 63 OH amp S Compliance Certification God Gawaca cages M Rippers 65 Specifications 66 67 Safety Rules 68 69 Safety Decals 70 Operation VG Daily Operators Checklist 2 Maintenance 73 Assembly Instructions 74 OH
15. FORMATION The purpose of this manual is to assist you in operating and maintaining your KANGA implement Read it carefully It provides information and instructions that will help you achieve years of dependable performance These instructions have been compiled from extensive field experience and engineering data Some information may be general in nature due to the unknown and varying operating conditions However through experience and these instructions you should be able to develop procedures suitable to your particular situation The illustrations and data used in this manual were current at the time of printing but in an effort to bring you better products we are always implementing continuous improvements that may vary your implement slightly in detail We reserve the right to redesign and change the machine as may be necessary without notice Some illustrations in this manual show the Digger with Safety Shields removed to provide a better view The Slasher should never be operated with any safety shielding removed Throughout this manual references are made to right and left direction These are determined by standing behind the equipment facing the direction of forward travel Blade rotation is as if viewed from the top Sank FARM EQUIPMENT TABLE OF CONTENTS Introduction Front amp 2 General Information 2 Post Hole Diggers H Specifications 6 7 Safety Rules 8 9 Safety Decals 10 Operation
16. Feb oMar cApr oMay oJun oJul oAug oSept Oct oNov o Dec Year ofManufacture _ Date of Purchased 7 7 Intended areas of use o Paddocks Only o Close to Sheds amp Buildings o Near Roads Contracting please spetify eS o Other please specify I have been fully instructed in the operation of this unit in the actual working conditions that I intended to operate and I am satisfied that I can use it safely I acknowledge that I have been fully instructed in the care maintenance lubrication and that Kanga Implements have been designed for agricultural use in area away from people animals roads and property I understand that there are Federal and State Laws as well as OH amp S Standards that dictate how I can operate should I wish to operate along roads or in any populated areas and that it is my responsibility to know and adhere to those laws I have received a copy of the operating manual and the dealer has instructed me to read the manual in full and carry out my own Risk Assessment before commencing any operations Owners Signature Date IAL ASSEMBLY Checked all hardware to ensure it is firmly tightened as outlined in the Operators Manual Customer has been instructed on how to make regular checks and tighten ALL hardware i c all nuts and bolts 2 LUBRICATION The implement has been lubricated and oil levels have been checked in all chain gearbox transmissions Customer has been instructed on how to check oil levels and lubricate implement
17. KANGA FARM EQUIPMENT OPERATORS MANUAL amp WARRANTY FORM Gavhall Pty Ltd trading as KANGA FARM EQUIPMENT would like to thank you for choosing one of our implements Kanga Farm Equipment has manufactured three point linkage implements to handle the harsh Australian Conditions since 1982 All new Kanga Farm Equipment Implements are backed with a 12 month comprehensive warranty against faulty workmanship and or materials under normal working conditions and service as outline in this manual Your warranty maybe considered void if any damaged to the implement is caused by operator abuse neglect or if any unauthorized modifications have been made Kanga Farm Equipment and its Distributors Dealers are not responsible for any transportation cost incurred in the repair or replacement of parts in either a successful or non successfil warranty claim All implements must be returned to the manufacture for warranty assessment This warranty does not exclude any conditions implied by the Trade Practices Act 1974 or any other relevant legislation The information contained in this manual was current at the time of printing and has been compiled especially to assist you with the Implement that you have purchased It is of the utmost importance that you read this manual understand the context and carry out a risk assessment before operating the implement Please be aware that in an effort to bring you better products we are always implementing cont
18. L NORMALLY CAUSED BY Too MUCH PRESSURE DEET broker or ste we foo To avad EC EE Za ee BROKEN CLEVIS ENDS NORMALLY CAUSED BY MEROPER CLEARANCE N THE MOUNT NG SPACHETS lewis casings can be brkan W eearanocs ara not daguate io alow rae mavemant the cyingar wen aly IER exer a verendeus aout i raare before they reach the and of the hing has ta give atian ha elevi cat ROUGH OF SCORED ron Tee tod eylnder rods are hard choma platad and wokiod amaga tho seats ana ramone eg roscoe or equent pasar BROKEN HERD CASTING NORMALLY CAUSED BY BENT PISTON ROD 1A sane rod besos bent EEN binder eased To ao so wil almost Inve ext Me oad casing crack or braak FARM EQUIPMENT Position the tractor so that the auger point is placed where the hole is to be dug Set the tractor s park brake Shift transmission into park or neutral Do not allow anyone to stand behind or to the side of a rotating auger Keep bystanders 10 meters away Lower auger point slowly to the ground using the Hydraulic Ram only with PTO disengaged The auger point should be approximately 100mm back of the centre of the gearbox As the auger works down into the ground it will straighten due to the pivoting action of the boom in a downward motion If the auger has side tilt correct with the tractor s 3 point linkage NOTE If the auger tilts too far forward or to the rear it maybe n
19. Rembve abd sine wenh bute starting engine Ne o oooo oOooooo0o0 ooo FARM EQUIPMENT Daily Pre Operation Checklist Operators Responsibility Operators MUST carry out a Risk Assessment and or HazCheck for the implement and ensure it is correct for the conditions the implement will be operating Review and follow safety rules outlined in this manual Check that all safety decals are installed and in good condition Replace in damaged Check that all shielding and guards are properly installed and in good condition Replace if damaged Consult local utilities before digging Know location and depth of all underground cables pipelines overhead wires and other hazards in working area and avoid contact Check that implement is properly and securely attached to the tractor Check that auger point and all cutting teeth are intact and in good condition Make sure PTO spring activated locking pin is well greased sides freely and is firmly seated in angular grooves Set tractor PTO at 540 rpm remembering only to operate at idle Lubricate all grease fitting locations Make sure PTO joints and shaftis well lubricated Check oil level in the gearbox Check all hardware ie bolts nuts shackles chains etc are properly installed secured and in good condition Make sure tractor 3 point linkage arms are adjusted so that implement cannot be lift to a point that there are extreme angles on the PTO shaft universals Set friction clutch as
20. ades the possibility of fast moving debris rotating PTO Shaft and ensure the customer knows that information about safe operating procedures and maintenance are in this Manual K ASSESSMENT Ensure you instruct customer to complete a HazCheck for the implement and their operating conditions 5 _ OWNERS OPERATORS MANUAL Check that the implement has a booklet supplied Emphasize the importance of reading the Manual Note manuals can be down loaded from www farmimplements comau Please tick the boxes above as each point has been carried out Dealership Name Salesperson s Nam Pre delivered By __ __ Salesperson s Signature Top copy manufacture Middle Copy dealer Last page purchaser 93
21. als are applied to the product where necessary Product Description Post Hole Diggers Model Number s XH Range Product Code s 55000 56000 H Range Product Code s 50000 M Range Product Code s 51000 Mini Range Product Code s 52000 Auger s Product Code s 50700 50600 50500 50400 50300 50200 50100 Name Position Date 01 06 2005 Details of the unit assessed for the purpose of compliance Model Auger Size Serial Date of Inspection Location Mini Range Es 050505 11 05 2005 16 Cahill St Dandenong M Range 15 210408 09 04 2008 16 Cahill St Dandenong H Range 12 930408 15 04 2008 16 Cahill St Dandenong XH Range 75hp 15 500504 03 05 2004 16 Cahill St Dandenong FARM EQUIPMENT PRE DELIVERY CHECKLIST Dealers Responsibility Inspect implement thoroughly after assembly to be certain it is set up properly before delivering it to the customer The following checklist is a reminder of points to inspect Check off each item as it is found satisfactory either before or after corrections or services performed co Check all bolts and ensure that they are tight a Check all cotter pins and linkage pins and ensure they are properly installed and can be secured o Refer to lubrication instructions and lubricate implement o Explain the importance of lubrication to the customer and point out all the lubrication points on the implement Check that any wear points i e points blades edges
22. amp S Compliance Certification 75 Stick Rakes 76 Specifications 77 Safety Decals 77 Safety Rules 78 79 Operation 80 81 Daily Operators Checklist 81 Maintenance 82 Assembly Instructions 82 OH amp S Compliance Certification 83 Harrows 84 Specifications 85 Safety Decals 85 Safety Rules 86 87 Operation 88 89 Daily Operators Checklist 90 Maintenance 90 Assembly Instructions 90 OH amp S Compliance Certification 91 Dealer Pre Delivery Checklist Ge ee Canes crete ihe 792 Warranty Registration and Installation Form 93 FARM EQUIPMENT FARM EQUIPMENT Post Hole Diggers Mini Range M Range H Range XH Range Hydraulic SPECIFICATIONS MINI RANGE 3 Point Linkage Boom Material Boom Material Measurements A Frame Material Type of Tower Gearbox Tractor PTO Speed Power Take Off Shaft PTO Clutch Size and Type of Clutch Linings Weight less auger Max Auger Size M RANGE 3 Point Linkage Boom Material Boom Material Measurements A Frame Material Type of Tower eege Tractor PTO Speed Power Take Off Shaft PTO Clutch Size and Type Of Clutch Linings Weight less auger Max Auger Size EE Boom Material aan Roach Boom Material Measurements A Frame Material Type of Tower Gearbox Tractor PTO Speed Power Take Off Shaft PTO Clutch Size and Type Of Clutch Linings We
23. are tight 2 Check the level of the gearbox oil daily and top up to correct level Check for gearbox leaks It should be noted that there is no warranty on a gearbox that has been operated without oil 3 Grease the PTO Shaft at the regular intervals specified in the Lubrication section of this manual 4 Check the wear to the auger pilot and teeth Sharpen routinely with grinder or replace when too far wom It is advisable to carry spare teeth and pilots Lubrication Information Do not let excess grease collect on or around parts particularly when operating in sand conditions The figure below show the lubrication points and gives the frequency of lubrication in normal operating hours based on normal operating conditions Severe or unusual conditions may require more frequent lubrication 40hrs Bhrs 40hrs 16hrs win 8hrs 40hrs Inner Joint Assembly Outer Joint Assembly When greasing implement be sure to clean fittings thoroughly before attaching grease gun Kanga Farm Equipment recommends Lithium Grease of 2 consistency for all locations unless otherwise noted Kanga Farm Equipment in conjunction with the gearbox manufacturer recommends high quality gear oil with a viscosity index of 80W or 90W Fill gearbox until oil runs out the side plug on the gearbox Check gearbox daily for evidence of leakage Have your dealer assist you should you find evidence of leakage Lubricate the PTO universal joint every eight operating hours Fai
24. ation is important An improperly installed seal will leak Always ensure the area where the seal outer diameter sits is clean Always inspect the area of the shaft where the seal sits and remove any burrs or nicks with emery cloth Always lubricate gear shaft and seal lips before assembling Remove and replace any seals damaged during assembly When assembling gearboxes always clean housing paying specific attention to areas where gaskets will be installed Wash housing and all components thoroughly Select a clean area where you can assemble the gearbox Replace any damaged seals bearings or gaskets All parts must be clean and lightly oiled before reassembled 35hp Gearbox f h Input Oil Seal Ee Output Oil Seal f Input Shaft Bearing Output Shaft Bearing 2 required Weight 22 kg Oil Ep 90 IL ern fe i ke CH FARM EQUIPMENT 50hp Gearbox Housing 60 40 10 Nodular Shafts UNS G10450 Gears UNS G51200 Seals Triple Lipped Spring Loaded Bearings Tapered Roller Oil EP 90 2L Weight 26 4kg Rotation ba 1 Top Housing 2 Cup amp Cone 2 required 3 Top Shim gasket Qty as required 4 Output Gear 5 Main Housing suit 1 s x 6 Spline Input Shaft 6 Output Shaft 7 Lower Seal 8 Inner Pinion Cup amp Cone 9 Pinion for models with 1 sx 6 Spline Input Shaft 10 Outer Bearing Suit 1 s x 6 Spline Input Shaft 11 Input Seal suit 1
25. ation on pages 8 9 amp 10 Post Hole Diggers are designed for one man operations You must always dig holes from sitting in the tractor seat It is the responsibility of the operator to see that no one comes within 50 meters of the digger when it is operating Accidents have occurred when more than one person is in the immediate area of the operating implement Be sure no one else is near you when you operate this product e Do not operate this digger unless all shields and guards are properly installed and in good working condition Replace if damaged Never place hands or any part of your body against auger gearbox PTO or boom to aim the auger Do not shovel dirt away from a running auger The shovel can be caught and thrown by the auger Consult local utilities before digging Know location and depth of all underground cables pipelines and other hazards in working area and avoid contact When dislodging a stuck auger disengage PTO stop engine remove key disconnect PTO and turn auger in reverse with a wrench Remove and store wrench and reconnect PTO before starting engine Keep hands feet hair and clothing away from equipment while engine is running Stay clear of all moving parts Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid oil under pressure can easily penetrate the skin and will cause serious injury or dea
26. aulic fluid oil penetrates the skin it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene serious injury or death will result e Always adjust the tractor lower linkage arms anti sway devices to prevent implement from swing from side to side during transport and operation Failure to do so may result in serious injury or damage Damage like bent and twisted implement towers are consumable items and are NOT covered by warranty Assembly of this implement is the responsibility of the KANGA FARM EQUIPMENT dealer It should be delivered to the new owner completely assembled lubricated and adjusted for normal conditions The digger is shipped partially assembled Select a suitable working area where all parts can be laid out Refer to accompanying text and part lists in this manual 19 FARM EQUIPMENT Attach A Frame to Boom A tractor is required during assembly ofa post hole digger A tractor will make part of the fit up alignment and handling easier 1 Connect the diggers Dual Rail A Frame to the tractors Lower Linkage Arms with the Lower Linkage Pins supplied and secure with lynch pins then secure with the tongue to the top link point of the tractors 3 point linkage Top link pin not supplied 2 Attach Boom to the holes located near the bend in the A Frame and secure with bolts amp nuts supplied 3 Attach the Hydraulic Ram to the A Frame and secure with pins and clips supp
27. ause damage to the PTO shaft It is best to raise the auger just enough to clear the hole when the PTO in engaged e Ensure that if you are operating the Post Hole Digger at a speed faster than idle that you reduce the speed back to idle before the auger comes out of the ground e Itis recommended NOT to raise the auger more than 150mm 6 above the ground while the auger is in operation Do not transport the implement with the PTO Shaft engaged To get a clean hole it is sometimes better to lower the auger into the hole with the auger rotating and then when at the desired depth stop the auger and raise the auger while it is NOT tuming This brings the dirt up leaving only a small amount in the hole Disengage the PTO when travelling between holes In some types of soil it may be necessary to use the 3 point linkage arms to prevent the auger from screwing itself into the ground too quickly When the ground is too hard to penetrate with your cutting edges and points sharpen or replace them and try again These are replaceable parts and must be in a good condition to penetrate the ground If you are having trouble penetrating the ground please refer to the Trouble Shooting section in this manual for suggestions XH Range Hydraulic Post Hole Diggers ONLY COMMON CAUSES FOR HYDRAULIC CYLINDER FAILURES et 18108 ROD NORMALLY CAUSED BY Ee G code er ates oy DE Ia e Cent unt er Sa en Kee STRETCHED TE RODS BLOWN BODY SEA
28. ecessary to move the tractor slightly Move tractor slowly and carefully so you do not bend the auger 6 With auger point lowered to the ground set the engine speed to idle then engage PTO Make sure auger point is on the ground before engaging the PTO A IMPORTANT Under no circumstances should the PTO be run at full throttle in 540 rpm No faster that half throttle in 540 rpm range 7 Ae the auger penetrates the ground lower the unit slowly with the Hydraulic Ram DO NOT LET THE AUGER SCREW ITSELF INTO THE GROUND The auger must be able to dig up the ground and carry it to the top by the auger flighting 8 Die the hole in small steps Dig down only 180 200mm at a time then raise the auger up to allow the soil to clear Repeat this procedure until the desire depth is reached This allows better control of the auger and prevents difficulties that could lead to an accident e Do not operate on steep slopes if in doubt set rear axles wider or only operate on moderate slopes e Do not stop start or change directions suddenly on slopes and traveling straight up and down is recommended e Use extreme care and reduce ground speed on slopes and rough terrain e Watch for hidden hazards on the terrain when traveling to where you will be operating YELLS TRANSPORT The Post Hole Digger auger is free swinging and care should be taken while transporting the implement Be sure auger is completely retracted from the hole before attempting t
29. ed in the tractor PTO splined angular groove To secure the PTO to the tractor you will see that there is a spring activated locking pin on both ends of the PTO Shaft Push this pin in and slide the PTO onto either the tractor output shaft or the implement input shaft Continue to slide the PTO onto the shaft until it becomes firmly seated in the angular groove Always ensure that both ends are locked into the angular groove before engaging the PTO Shafi e Depending on the model of tractor that is being used with the implement it may be possible for the PTO to operate when the joints are at the maximum angle Operating a shaft at the maximum angle will quickly shorten the life of you PTO Shaft FARM EQUIPMENT Your PTO shaft and the safety covers do comply with AS1121 4 and as a result it will be clearly labeled with instructions to show which end should be fitted to the tractor and which should be fitted to the implement Please follow the labels carefully so that you do not void your warranty Always check the range of movement before operating Set friction clutch as outlined in this manual Vibration tends to loosen bolts during operation All hardware should be checked regularly It is good practice to check implement before each operation to ensure all hardware is secure PTO Shaft Maintenance Shaft Operating Angle Adjust tractor hydraulic control to minimise lift height High lift and large shaft angle will destroy universal
30. equipment for eyes hair hands hearing and head Gearbox Maintenance Fill gearbox with high quality gear oil with a viscosity index of 9OW Fill gearbox until oil runs out the side plug on the gearbox Gearbox Oil should be changed every 1000 hours of use or every two 2 years Always drain oil into a container and dispose of it properly to protect the environment Oil level must be checked daily The composition of oil deteriorates over time and the intense heat that occurs when operating a gearbox reduces the oil level Low oil levels will result in wear of gearbox components that overtime will result in component failure that could have been prevented Repair to this gearbox should be limited to replacing bearings seals and gaskets Replacing gears shafts and a housing is not cost effective It is more economical to purchase a complete gearbox if repairs other than bearings seals and gaskets are required It is highly recommended that the customer be given the costs involved in both scenarios as a new gearbox comes with a new warranty gearbox only Inspect gearbox for leakage and bad bearings Leakage is a very serious problem and must be corrected immediately Excessive noise and side to side or endplay in the shafts indicate bearing failure Leakage can occur at the vertical or horizontal gasket and shaft seals Leakage from the horizontal gasket or seal can be repaired without removing the gearbox from the slasher Proper seal install
31. especially when operating controls or starting engine Place transmission in neutral engage break and ensure all other controls are disengaged before starting tractor engine Do not operate tractor PTO during transport or when implement is raised more than 150mm above the ground Look down and to the rear and make sure area is clear and safe before traveling in reverse Do not stop start or change directions suddenly when traveling on slopes Use extreme care and reduce ground speed when traveling on slopes and rough terrain Stop implement then tractor immediately upon striking an obstruction Turn off engine remove key inspect and repair any damage before resuming operations Always block implement when inspecting Before commencing any adjustment maintenance or cleaning Always disengage the Power Take Off PTO Shaft switch off the tractor engine remove key and wait until all moving parts have come to a complete stop then ensure the machine is on the ground or on a robust secure support Before dismounting tractor or performing any service or maintenance disengage power to implement lower the 3 point linkage and any other raised components i e loader bucket to the ground Operate valve levers to release any hydraulic pressure stop engine set parking brake remove key and unfasten seat belt Disconnect driveline from the tractor PTO before performing any service work Never place any part of the body underneath the implement or bet
32. esponsibility of the KANGA FARM EQUIPMENT dealer It should be delivered to the new owner completely assembled lubricated and adjusted for normal conditions The digger is shipped partially assembled Select a suitable working area where all parts can be laid out Refer to accompanying text and part lists in this manual Boom Attach A Frame to Boom A tractor is required during assembly of a post hole digger KH Ba K geb A tractor will make part of the fit up alignment and A Frame Boom Pin Co 7 handling easier i d 1 Connect the diggers A Frame to the tractors Lower Ui MA Een Linkage Arms with the Lower Linkage Pins supplied and DV wy Ey secure with lynch pins Top Link Point A y A 2 Attach Boom to the top link point of the tractors 3 E ES V ZG point linkage Top link pin not supplied ps fm 3 Afen A Frame with the adjustment holes on the boom Guards 2 Safety SEN A di j start with middle hole and secure into position with Pin i Auger Lower Linkage arms FARM EQUIPMENT With boom attached to tractor raise boom by hand Check clearance between boom and top of A Frame If interference exists change hole location Now use the tractors 3 point lower linkage arms to check range of movement Failure to check can result in damage to tractor or implement Attach Safety Covers Place gearbox upside down on a suitable work surface and attach the black plastic guards to the housing of the gearb
33. ess holes is not good enough 1 If 80 degree wide angle shafts are angled at greater than 80 degrees Jack knifing implement with shaft stationary or rotating the centre support ball and socket will break not covered by warranty To avoid over angling fit turn limiters to your implement draw bar Correctly fitted turn limiters will con tact tractor tyre prior to over angling 2 The very large centre disc lubrication cavity must be completely full before any grease transfers from the cavity to the centre support ball and socket More than half a cartridge of grease is required to fill this cavity on initial shaft installation 3 Wide angle covers should be completely removed to ensure grease flows to the centre support ball and all eight cross bearings FARM EQUIPMENT The Clutch Gearbox protection is provided by a slip clutch with replaceable discs The slip clutch is designed to slip and when excessive torsion loads are encountered Kanga 150mm 6 Two Plate Slip Clutch 1 134 x 6 Spline base assembly includes bush 2 Bush 1 4 ID 3 Friction Disc 5 OD x 1 3 ID 2 required 4 1 x 6 Spline Drive Plate 5 OD x 1 IV Dia Spigot 5 Pressure Plate 6 Spring 6 required Kanga 200mm 8 Two Plate Slip Clutch 1 1 3 8 x 6 Spline base assembly includes bush A mm 2 Bush 14 ID e 3 Friction Disc 6 4 OD x 2 ID 2 required 0 p03 4 1 g x 6 Spline Drive Plate y 5 Outer
34. familiar with this form of injury or gangrene serious injury or death will result CONTACT A PHYSICAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY e Know your controls and how to stop quickly in an emergency Operators must be instructed in and be capable of the safe operation of the equipment and all controls Do not allow anyone to operate this equipment without proper instruction Do not allow children or untrained persons to operate equipment Check that all hardware is tight and properly installed e Always wear relatively tight fitted clothing to avoid entanglement in moving parts Wear heavy duty rough soled boots and protective equipment for eyes hair hands hearing and head Ensure implement is properly attached adjusted and in a good condition so that it can be operate safely Make sure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and are firmly seated in the tractor PTO splined angular groove Before commencing operation check all equipment driveline guards for damage and make sure they rotate freely Replace any damaged guards or guards that do not rotate freely on drivelines e Tractors MUST be fitted with Roll Over Protection Structure ROBS or ROBS Cap Itis also advisable that your tractor be fitted with a seatbelt where fitted it must be worn at all times Falling from your tractor can result in death from being run over or crus
35. hed If your tractor is fitted with a folding ROBS keep itin the locked up position at all times Inspect chains shackles deflectors and any wear parts for damage Replace if damaged Remove any debris that has accumulated on the implement tractor or engine to avoid fire hazard Ensure all safety decals are installed Replace if damaged Ensure shields and guards are properly installed and in good working condition Replace if damaged A minimum 20 of tractor and equipment weight must be on the tractor s front wheels with implement in the transport position Without this weight tractor could tip over causing personal injury or death The weight maybe attained with a loader front wheel weights and ballast in the tyres or front tractor weights When attaining the minimum 20 weight on the front wheels you must not exceed the ROPS max ballasted mass certificate Weight the tractor and implement Do not estimate Inspect operating area remove where possible any stones or foreign objects that may cause injury or damage It is very important to always watch for foreign objects in the area you are operating and avoid any that could cause injury or damage FARM EQUIPMENT When working in populated areas always place signs in the area to alert people or vehicles that may pass Operation must be stopped when anyone comes within 50 meters Keep all people and animals away from the implement during start up operating and when st
36. ight less auger Max Auger Size sank FARM EQUIPMENT Category 1 Rolled Hollow Section RHS 80x 80x4 65 x 12 Flat Double Clevis Reinforced 35hp 2 92 1 ratio Idle 540 rpm Series 2 1500mm 6 Slip Clutch 5 92kg 12 305mm Category 1 Rolled Hollow Section RHS 100x 100x 6 65 x 12 Flat Double Clevis Reinforced 50hp 3 18 1 ratio Idle 540 rpm Series 4 1500mm 6 Slip Clutch 2 133 6kg 24 610mm Category 1 Rolled Hollow Section RHS 100x 100x 6 65 x 12 Flat Double Clevis Reinforced 75hpt 4 1 ratio Idle 540 rpm Series 4 1500mm 8 Slip Clutch 2 159 2kg 24 610mm Specifications for this Gearbox can be found on page 25 of this Operators Manual Specifications for this Gearbox can be found on page 26 of this Operators Manual Specifications for this Gearbox can be found on page 26 of this Operators Manual CN FARM EQUIPMENT XH RANGE Category 1 or 2 3 Point Linkage Material Rolled Hollow Section RHS Construction Heavy Duty Dual Rail with shear bolts A Frame Material Rolled Hollow Section RHS Tractor PTO Speed Idle 540 rpm Hydraulic i 2 5 Hydraulic Ram amp hoses Gearbox na see as see sos ae oes er oer ser rer SOhp 3 18 1 Reduction 75hpt 4 1 Reduction ET ME 50hp Gearbox Series 4 75hp Gearbox Series 6 Clutch Friction Slip Clutch Size of Clutch 50hp
37. inuous improvements that may change the designs and specifications of the Implement In doing this Kanga Farm Equipment together with its Dealers and Distributors are under no obligation to implement these changes free of charge on any previously delivered Implement Kanga Other Products Manual docx 16 Cahill Street Dandenong Victoria Australia 3175 Tel 03 9706 5166 Fax 03 9706 5050 PROP GAVHALL PTY LTD ACN 006 050 657 ABN 59 918 752 500 FARM EQUIPMENT TO THE DEALER Assembly and proper installation of this product is the responsibility of the KANGA FARM EQUIPMENT dealer The dealer must complete all items on the Warranty Registration amp Installation Form included in this manual before releasing the implement to the new owner Both dealer and customer must sign the registration which certifies that all Dealer Checklist items have been completed The dealer must retum a copy of the Warranty Registration amp Installation Form to Kanga Farm Equipment Reminders about Warranty Registration that have not been returned will be sent out to demonstrate that reasonable attempts have been made to ensure dealers complete risk assessment and pre delivery obligations TO THE OWNER Read this manual before operating your KANGA FARM EQUIPMENT implement The information presented will prepare you to do a much better and safer job Keep this manual handy as a reference Ensure you carry out and keep up to date a Risk Assessment
38. ion are dependent upon the awareness concem prudence and proper training of personnel involved in the operation transport maintenance and storage of equipment Ithas been said The best safety device is an informed careful operator We ask you to be that kind of operator Customers MUST carry their own Risk Assessment and or HazCheck on every implement on their property Safety instructions are important Read all attachments and unit manuals follow all safety rules and safety decal information Failure to follow instructions can result in serious injury or death If you do not understand any part of this manual and need assistance the Department of Agriculture Occupational Health amp Safety Offices any Agricultural School or college and your local dealer should be able to direct you on where you can receive appropriate training No operator however experienced in farm machinery operation they maybe should attempt to use any piece of machinery that they have not been competently trained to use Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid oil under pressure can easily penetrate the skin and will cause serious injury or death Make sure that all operating and service personnel know that if hydraulic fluid oil penetrates the skin it must be surgically removed as soon as possible by a doctor
39. joint All Bare Co PTO shafts single universal joint Short time running Maximum angle 25 degrees Continuous operation Maximum angle 17 degrees All Bare Co Wide Angle PTO shafts double universal joint Short time running or stationary Maximum angle 80 degrees Continuous operation Maximum angle 25 degrees LUBRICATION Sliding Members Use high temperature grease similar to HP multi purpose chassis grease Grease sliding members prior to assembly and after every 20 hours of use For applications with high tele scoping movement grease every 8 hours Bare Co shafts from 8 series upwards are equipped with a grease nipple which can be accessed by releasing the patent guard to align access hole Universal Joints Grease standard joints every 20 hours or 8 hours for severe conditions Wide angle joints every 8 hours un der wide angle conditions Operating standard shafts at greater than 10 degrees angle or wide angle shafts at greater than 18 degrees angle dramatically reduces cross bearing life and requires more frequent lubrication IMPORTANT Grease follows the easiest path through internal ports to the four cross bearings Over heating and poor quality grease baked in one port will prevent grease reaching that bearing resulting in failure of indi vidual cross bearings Typical cross failure due to blocked internal grease port Fully open guard covers to ensure grease flows to all cross bearings Greasing through small guard acc
40. lied 4 Lift Dual Rail Boom into a position where you can now attach the other end of the Hydraulic Ram to it Again secure with pins and clips supplied 5 Attach the Hydraulic Hoses Always ensure hydraulic hoses are able to move within the range of the boom but are not hanging in a position where they can become tangled in moving parts Return to your tractor seat and slowly lift the lower linkage until implement is rigid and locked into position The implement will be locked into position once the tongue has taken some load Do not lift too quickly or to high as you will bend the tongue and the A Frame BEN SE Sa Sieg SE The lower section of his frame between he two 2 X s must Ce Covers 7 Ab SE noies in te roe g Saye en you use two 2 bot in th tangue F etme wat SoS ts oc ane Become ngia eee below Only raise the boom with the Hydraulic Ram once you have the A Frame in place Operating the 3 point lower linkage arms of the tractor in conjunction with the Hydraulic Ram will cause you to bend the tongue of the A Frame Always check the range of movement slowly Attach Safety Covers Place gearbox upside down on a suitable work surface and attach the black plastic guards to the housing of the gearbox on both the input and output shafts using the four cap screw and flat washers supplied Gearbox to Boom 1 Attach the desired auger to the output shaft of the gearbox and secure u
41. lure to service will result in damage to the gearbox You will find a level plug on the side of your gearbox or a guide to the amount of oil required can be found on the same page as the gearbox parts guide o Instruct the customer that they MUST carry out a Risk Assessment and or HazCheck for the implement and the operating conditions O Ensure the customer has signed the WARRANTY REGISTRATION amp INSTALLATION FORM and a copy has been returned to Kanga Farm Equipment 16 Cahill Street Dandenong Victoria 3175 Name of person who carried out Pre delivery Signature Dealership Name Location carried out Date Top copy manufacture Middle Copy dealer Last page purchaser 92 KANGA FARM EQUIPMENT WARRANTY REGISTRATION amp INSTALLATION FORM Owners Name Tow Type of Implement Purchased o Post Hole Digger Mini Range OMRange oHRange oXH Range 50hp o XH Range 75hp o Box Scrapper o 1200mm o 1800mm 0 2400mm o Carryall opa BEEN 06 x36 o Cultivator o Eurvtiller 5 7 9 11 Tine oS Tine 24m 2 8m 3 0m 3 2m o Chisel Plough 5 7 9 11 Tine Pallet Fork o 500kg o 1000kg o Bale Equip o Spike o Silage Fork o Adj Bale Feed Out Fork ORipper oH Range3 Tine oMRange3 Tine oH Rang Single Tine oM Range Single Tine Mini Single Tine o Stick Rake 2 1800mm 2 2400mm BEE o Harrows 2400mm 23000mm 3600mm 5 4000mm Harrow Rake o Other Please Specify Serial Number Month of Manufacture aJan
42. lure to maintain proper lubrication could result in damage to Universal Joints gearbox and driveline To lubricate the shaft itself lower implement to the ground disconnect PTO Shaft from tractor and slide the PTO halves out until almost disconnected from each other Apply a bead of grease completely around male half where it meets the female half Slide over each other several times repeatedly to distribute grease STORAGE Post Hole Diggers once off the tractor can be an awkward piece of equipment to handle Be careful not to pinch hands and fingers in the various hinge points of the digger If possible hang the digger from an overhead rafter or beam Attach some heavy duty chain or rope around the boom just in front of the gearbox This will allow one person to easily reconnect the digger to the tractor when it is next required If storing outside another idea is to dig a hole about 300 450mm deep Then shut the PTO off while the auger is in the hole Set park brake tum off engine then disconnect the PTO and the digger from the tractor The auger in the hole will keep the unit upright and make it possible for one man to disconnect or reconnect the digger to the tractor This method of storage will cause rusting to the auger but it is easy for one man to handle the unit If possible remove the PTO shaft completely and store undercover If the digger has been stored for a long time in either of the above mentioned methods or another way
43. measure ment step 1 Less 75mm 3 Cut this amount off both inner and outer drive tubes Remove burrs and grease tubes E g New shaft 1194mm 47 B sch FREE TRAVE Less grove to groove requirement 890mm 35 Less clearance 75mm 75mm 3 Amount to cut off 229mm 9 e This is example only R I Insert your own measurements FARM EQUIPMENT KT EE e Your PTO shaft and the safety covers do comply with AS11214 and as a result it will be clearly labeled with instructions to show which end should be fitted to the tractor and which should be fitted to the implement Please follow the labels carefully so that you do not void your warranty To avoid damage to the covers of your PTO Shaft always slowly lower the shaft when disconnecting it from your tractor To prevent damage and for longevity when the implements is not in use always remove the PTO shaft from the clutch and store in a cool dry place e Always wear relatively tight fitted clothing to avoid entanglement in moving parts Wear heavy duty rough soled boots and protective equipment for eyes hair hands hearing and head when carrying out any servicing or operational tasks Always check the plastic guarding on PTO shaft and the plastic clutch cover on the gearbox If wom or damaged replace immediately Make sure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and are firmly seat
44. o move the tractor DO NOT transport the Post Hole Digger while the PTO is engaged as this could cause the universal joints of the PTO to operate on an extreme angle and cause the failure of the drive shaft Pay close attention to the Safety Messages regarding transportation of this implement Avoid unnecessary injuries and equipment damage by exercising cautious conscientious travel procedures Attaching the implement to the tractor increases the overall length of the working unit Allow additional clearance for the implement to swing when tuming Raise the implement as high as possible for transporting e When dislodging a stuck auger disengage PTO stop engine remove key disconnect PTO and turn auger in reverse with a wrench Remove and store wrench and reconnect PTO before starting engine e Removing a lodged auger can be dangerous work Be careful DISLODGING A STUCK AUGER If the auger gets stuck in wet clay stones or roots disengage the PTO immediately and tum off the tractor engine Tum the auger backwards several turns with a large pipe wrench Than attempt to raise the auger with the 3 poit linkage arms Extreme rocking or lifting loads while trying to clear the auger can cause auger gearbox or boom failure NOTE Do not attempt to raise the auger while tum it with the wrench or with a wrench attached to the auger You could be injured if the PTO was accidentally engaged or if the 3 point linkage arms suddenly raise the auger 3
45. on the implement ann FARM EQUIPMENT SAFETY RULES amp ACCCIDENT PREVENTION A ATTENTION BE CAREFUL YOUR SAFETY IS INVOLVED A Replace Immediately if Damaged Mini Range Post Hole Digger 3 Model ie S M H etc 1 Serial Number Plate 2 Kanga Logo EEKANNA AA i cae KANGA Wees FARM EQUIPMENT 5 Safety Decal 6 Safety Decal K0004 x2 4 Safety Decal 7 Safety Decal K0006 8 Safety Decal 9 PTO Safety Decal x3 DANGER MH Range Post Hole Digger Pictured right XH Range Post Hole Digger Pictured below e 10 FARM EQUIPMENT OPERATION Safety is a primary concern in the design and manufacture of our products Unfortunately our efforts to provide safe equipment can be wiped out by a single careless act of an operator In addition to the design and configuration of equipment hazard control and accident prevention are dependent upon the awareness concem prudence and proper training of personnel involved in the operation transport maintenance and storage of equipment It has been said The best safety device is an informed careful operator We ask you to be that kind of operator The operator is responsible for the safe operation of this implement The Operator must be properly trained Operators should be familiar with the implement and tractor and all safety practices before starting operation Read the safety rules and safety decal inform
46. opping Never place hands or any part of your body against auger gearbox PTO or boom to aim the auger Shift tractor transmission into park or neutral and set park brake before engaging PTO and digging Keep digger under control by running PTO at slowest speed possible No faster than half throttle in 540 rpm range Always ensure the correct setting of 540 rpm is selected on your tractor before start up Use extreme care when working close to fences ditches hillsides or other obstacles Do not operate or transport on steep slopes If in doubt set rear axles wider for moderate slopes When digging on unstable or hilly terrain place digger uphill from the tractor When dislodging a stuck auger disengage PTO stop engine remove key disconnect PTO and turn auger in reverse with a wrench Remove and store wrench and reconnect PTO before starting engine Never leave a tractor and implement running unattended Do not operate the implement or tractor while under the influence of drugs or alcohol Operate only in daylight or good artificial light Keep hands feet hair and clothing away from moving parts while engine is running For transportation on public roads the operator must ensure that the tractor and implement complies with current State and Federal laws and must strictly adhere to all road traffic regulations in force in his her particular state Always operate equipment from the seat of the tractor with the seat belt securely fastened
47. ox on both the input and output shafts using the four cap screw and flat washers supplied Gearbox to Boom Attach the desired auger to the output shaft of the gearbox and secure using the bolt and nut provided Stand gearbox and auger assembly on the auger point Place gearbox and auger assembly under boom and slowly lower 3 point linkage arms of tractor Align gearbox mounting lug and boom Secure together using pin and cotter pins provided Attach the PTO Shaft EE XH RANGE ASSEMBLY INSTRUCTIONS e Keep hands feet hair and clothing away from equipment while engine is running Stay clear of all moving parts e During routine checks repairs and when performing adjustments keep all persons away from operators control area ensuring that no one can switch on the tractor or Implement e Make sure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and are firmly seated in the tractor PTO splined angular groove e When connecting the tractor to the implement always find somewhere level or flat e Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid oil under pressure can easily penetrate the skin and will cause serious injury or death CONTACT A PHYSICAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY e Make sure that all operating and service personnel know that if hydr
48. re lowered to the ground or raised unless it is properly blocked and secure Never place any part of the body underneath the implement or between moveable parts even when engine has been turned off Hydraulic systems can creep i e slowly lower They can fail or movement of the control levers can cause the implement to drop or rotate unexpectedly causing severe injury or death Follow Operator s Manual instructions for working on your implement correct blocking procedures or have work carried out by a qualified dealer Keep hands feet hair and clothing away from equipment Stay clear of all moving parts Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid oil under pressure can easily penetrate the skin and will cause serious injury or death CONTACT A PHYSICAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY Make sure that all operating and service personnel know that if hydraulic fluid oil penetrates the skin it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene serious injury or death will result Always wear relatively tight fitted clothing to avoid entanglement in moving parts Wear heavy duty rough soled boots and protective equipment for eyes hair hands hearing and head FARM EQUIPMENT ROUTINE MAINTENANCE 1 Check that all bolts nuts and screws
49. sing the bolt and nut provided 2 Stand gearbox and auger assembly on the auger point 3 Place gearbox and auger assembly under boom and slowly lower the Hydraulic Ram with the tractors remotes 4 Align gearbox mounting lug and boom Secure together using pin and cotter pins provided Next attach the PTO Shafi FARM EQUIPMENT The Power Take Off Shaft PTO PTO shafts come in standard lengths so that they can be adapted to all tractors This means that you may have to shorten the PTO Shaft to suit your tractor Failure to shorten your PTO shaft may result in End Thrust End Thrust can destroy your tractors internal drive and or the Slashers Clutch and or Slasher Gearbox This damage will not be covered by warranty To shorten your shaft please follow the steps below 1 2 3 4 Measure groove to groove dis tance from implement shaft to tractor shaft with implement in shortest position NOTE Length will vary as imple ment is raised or lowered Remove safety guard from new shaft and measure length between shaft lock buttons or clamp bolts with shaft in closed position Required length of shaft is groove to groove length step 1 less a minimum of 75mm 3 to allow for disconnection from trac tor and prevent end thrust damage If shaft is shorter than this ensure that 50 of telescopic tubes over lap Amount to cut off shaft Length of new shaft step2 Less groove to groove
50. t be able to raise or lower through the highest and lowest points of the tractors 3 point linkage arm travel without any part of the Post Hole Digger touching against itself or the tractor frame Check carefully BEFORE attaching the auger If it does touch adjust the tractors 3 point linkage and or vary the position of the A Frame in the boom so that all movement is free Use stabilizer bars adjust sway chains or sway blocks on the tractor 3 point linkage to keep the Post Hole Digger from swaying side to side Adjust as tightly as practical for best performance A IMPORTANT e Post Hole Digger gearboxes are shipped without lubricant Fill gearbox with high quality gear oil with a viscosity index of 90W before operation e If PTO Drive Shaft interferes with drawbar swing drawbar out of the way or remove OPERATING TECHNIQUE Mini M H Range Post Hole Diggers e Never place hands or any part of your body against auger gearbox PTO or boom to aim the auger e Do not shovel dirt away from a running auger The shovel can be caught and thrown by the auger A IMPORTANT e Never use body weight in an attempt to help the auger penetrate the ground Position the tractor so that the auger point is placed where the hole is to be dug Set the tractor s park brake Shift transmission into park or neutral Do not allow anyone to stand behind or to the side of a rotating auger Keep bystanders 10 metres away Lower auger point slowly to the ground with
51. t half a tum at a time until clutch is no longer slipping 0 If springs are compressed to 24mm check friction discs for excessive wear Discs are approximately 3 2mm thick when new Replace discs after 1 6mm of wear Minimum disc thickness is 1 6mm Dne KS a Every individual is operating in a slightly different environment with a range of variables that determine how the clutch must be set for their operation The size of the tractor the size of implement and the work being carried out and the terrain are all factors that determine the clutch setting A quarter or halfa tum can make a big difference Itis for this reason that each clutch should be reset for your operating conditions FARM EQUIPMENT GEARBOX SERVICE The information in this manual requires special skills and tools If you are not properly equipped or your mechanics are not properly trained in this type of repair you may void your warranty or cause more damage leading to a larger repair bill e Before working underneath read manual instructions securely block up and check stability Secure blocking prevents equipment dropping from hydraulic creep i e slowly lowering hydraulic system failure or mechanical component failure e Keep all persons away from operator control area while performing adjustments service or maintenance e Always wear relatively tight fitted clothing to avoid entanglement in moving parts Wear heavy duty rough soled boots and protective
52. th CONTACT A PHYSICAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY Make sure that all operating and service personnel know that if hydraulic fluid oil penetrates the skin it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene serious injury or death will result Do not put digger into operation unless auger point and all cutting edges are intact and in good repair Do not allow children or untrained persons to operate this implement Keep bystanders at least 50 meters from equipment when operating Keep all people and animals away from the implement during start up operating and when stopping Make sure all spring activated locking pins or collars on the Power Take Off PTO Shaft move freely are well greased and are firmly seated in the tractor PTO splined angular groove e When working in highly populated areas always place signs in the area to alert people or vehicles that may be passing e When digging holes always sit in the tractor operators seat e Shift tractor transmission into park or neutral and set park brake before engaging PTO and digging Keep digger under control by running PTO at slowest speed possible No faster than half throttle in 540 rpm range A CAUTION e Always wear relatively tight fitted clothing to avoid entanglement in moving parts Wear heavy duty rough soled boots and protective equipment for eyes hair hands hearing and head
53. ween moveable parts even when engine has been turned off Hydraulic systems can creep i e slowly lower They may fail or movement of the control levers can cause the implement to drop or rotate unexpectedly causing severe injury or death Follow Operator s Manual instructions for working on your implement or have servicing carried out by a qualified dealer During routine checks and or repairs ensure that no one can switch on the tractor or Implement accidentally Keep the key to the tractor in your pocket For your own safety and that of others and to avoid forfeiting your warranty use only original spare parts Do not modify alter or permit anyone else to modify alter the implement or any of its components Ensure implement is properly attached adjusted and in good operating condition Frequently check teeth amp pilot They should be sharp free of nicks and cracks and securely fastened Do not handle teeth amp pilot with bare hands Careless or improper handling may result in serious injury Your dealer can supply you with genuine replacement parts Firmly tighten all nuts bolts screws and shackles before operating If worn or damaged then replace immediately Block implements securely for storage Keep children and bystanders away from storage area Kanga Farm Equipment accepts no responsibility or liability for any losses injuries or damages that may result from failing to observe these safety rules and the safety decals
Download Pdf Manuals
Related Search