User Guide - Pool Cover
Contents
1. cover in place 2 Always double check your measurements before you cut trim the cover 3 For pools without bullnose edge and for pools with a wet edge overflow you may want to trim cover back to the waterline REMEMBER BUBBLE SIDE FACING THE WATER GENERAL TIPS FOR USE In order for you to enjoy the Aussie Pool Cover for a long time we ask that you follow some basic instructions which will help extend the life expectancy of your Aussie Pool Cover and to guarantee optimum performance Our covers are made from a specially designed PE compound for extra strength and durability however here are some tips to protect your investment e Remove the cover first before you use the pool and enter the water e Keep the cover rolled up neat and evenly when using the roller e Do not drag and pull the cover over paving timber decking or other hard surfaces e Don t let the cover catch on any corners or steps when rolling up or folding up e f you do not have a cover roller you should use another person to help with folding up the cover e Arolled up or folded up cover should always be stored out of direct sunlight e Do not leave your cover laying on top of a lawn because of its heating capabilities it could burn and damage your lawn within a very short time e Ensure the cover is clean and dry if you are going to store it away for a long period of time e Our pool covers can be easily hosed down and cleaned with a soft brush in order to remov2. Product Purchase Date aa WARRANTY CONDITIONS Our goods come with Guarantees that cannot be excluded under the The warranty is void if i e AUSA ORSENT AN 1 The purchaser fails to comply with the manufactures A purchase receipt or a similar proof of purchase of the goods should be installation instructions retained by the customer at all times A warranty claim will not be valid 2 Damage caused from pool chemicals including chlorine at a without the proof of purchase and a receipt higher level than normal This warranty only applies if the products have been installed and used in accordance with the manufacturer s recommendations under normal use and reasonable care 3 Damage caused by super chlorination l R O L L E R S 4 Damage caused by leaving the cover rolled up or by any other means of storage in full sun 5 If the cover or roller has been damaged in any way due to This warranty does not cover color fading of the product or deterioration abuse tampering modification neglect accidental or in the chemical composition even if it s due to UV exposure improper use All claims under this warranty must be made in writing addressed to The cover is stored at above 45 degrees Celsius Iser Guide Aussie Pool Covers Pty Ltd 7 Pool roller exposure to sun which may cause damage to rolled up cover This warranty covers the purchaser for defective material or workmanship on a pro rata basis Damage is caused by handli
3. e debris and dirt e Dirt and debris such as leaves can be easily hosed off by hosing it towards the skimmer box making sure that the pool pump and filtering system is running e Always maintain the recommended chlorine levels A higher than normal chlorine level can damage the cover e Always keep pool cover off for at least 48 hours after super chlorination e The pool solar cover is not a safety cover it will not carry the weight of any person e Do not attempt to walk on the cover e Never try to swim underneath the cover e Do not sit on the pool cover roller
4. ng freighting or transportation of the product You are entitled to a pro rata refund or discount on a new cover for the Product Pro rata warranty remaining warranty period Please see warranty periods below amp YP YP 400 micron 5 years 500 micron 6 years 600 micron 8 years Note The first year is a full warranty on defective material or workmanship thereafter on a pro rata basis as listed in the above table POOL COVER INSTALLATION PROCEDURE To install your solar pool cover 1 Be careful when using any sharp tools not to damage the cover when unpacking 2 Unfold the cover and lay the pool cover WITH AIR BUBBLES SIDE ON THE WATER 3 Make sure the cover sits flat on top of your pool water and that the surface of the water is completely covered including any recessed areas such as steps 4 Before you start cutting the cover to shape you may want to draw the outline of your pool on the smooth side of the cover 5 Use a pair of very sharp scissors to cut the cover to shape We suggest leaving at least 4cm 6cm extras on each side which will rise up on the pool side not a requirement This can be trimmed later on if required Having the side of the cover rising up will stop any debris such as leaves entering the water These can be washed off with a hose 6 The cover does not require attaching points or fixing to the pool it is designed to sit on the water Tips 1 Use another person to help to hold the
Download Pdf Manuals
Related Search