Operating Instructions
Contents
1. This prevents any possible damage to pipes and boiler All maintenance procedures must be carried out exclusively by authorized technicians and all soare parts must be genuine Any modification or forcing performed by persons not authorized by the Manufacturer will void all warranties covering the appliance The motor pump set must be position far from hydraulic pipes heat sources electrical appliances or it must be protected by a water resistant aerated enclosure WARNING Before performing tests and maintenance procedures DISCONNECT MACHINE FROM MAINS Never pull the electrical supply cable Unplug the machine or turn off the main switch before cleaning the machines interior Never use detergents of any kind To reduce the risk of electrical shock avoid operating the machine with wet hands or feet and do not operate the machine with bare fee The machine has to be installed with an efficient ground system the Manufacturer recommends a wooden platform on which the operator can stand Never touch coffee groups spouts steam and hot water pipes They are HOT and could cause burns Never operate the machine without water The machine must be operated with clean water This must be filtered water with filters replaced every 6 months Use water softeners if the water has a high mineral content Mineral deposits may obstruct the machine s water circuit which may cause damage to the machine and possibly personal injur2. Once the dose for one brewing group is set the same dose will be simultaneously set in the other group however for a more accurate dosing we recommend fo program each group keyboard individually The programming operation between a key and the other has to be completed within 30 seconds otherwise the memory will be lost For partial keyboard dose setting push star key again after the last selected dose key has been programmed pp E E STREAMLING supplies Maintenance Manufacturer recommended cleaning procedures to be performed at the end of each working day Clean showers group gaskets group flange with a brush Wash filfers and filter holder in warm water adding a special detergent product for use with coffee machines Put the filter holder with the blind filter in the coffee delivery group and press the button for semi automatic coffee delivery Switch it off after 15 seconds Remove the filter holder and take the blind filter out Clean the cup tray and grid without removing the tray from the machine Clean the steam wands and spout accurately with a non abrasive damp cloth immediately after each single to prevent clogging of the steam holes and taste persistence of previously steamed drinks Do it without touching the wands directly Caution HOT Surface Manufacturer recommended weekly cleaning operations The group and shower plate are cleaning by putting one teaspoon of special espresso mach
3. any mm m ii i T ar E gt P This machine is designed for the sole purpose of producing coffee hot water and steam for hot drinks All other uses are incorrect and therefore dangerous This machine is designed for professional use only The machine components are made of non toxic and long lasting parts which are easily accessed for cleaning and maintenance The end user must be an adult sufficiently trained to operate the appliance properly and it must forbid the use of the appliance to children or non responsible persons To ensure efficient and correct operation it is essential to follow the Manufacturer s instructions concerning the periodic maintenance carried out by authorized technicians in compliant with the local standards and laws The installation technician the user and the person in charge of maintenance are obliged to inform the manufacturer of any defects or damages which could affect the safety of the original installation The installation technician must check the surrounding area to ensure safe and hygienic use are guaranteed The machine components Manufacturers are responsible for the parts supplied by them The Customer is responsible for the personal use of the equipment Do not expose the machine to environmental elements sun rain etc When the machine is idle and not in use for an extended period of time it should be emptied completely and stored in an area with temperature above freezing 0 C or 32 F
4. Security valve 12 Delivery group solenoid valve 13 Pressure switch 14 Volumetric counter flow rate sensor L QW RD Ww 110 SO CON OO OM ADA www streamlinesupplies com au_ 12 STREAMUNE supplies Electrical Diagram Semi Automatic EROICA S 2 230V 4 i 3 A LT LA er 1 Main switch 2 Heating element thermal protector Pressure switch Heating element Mains pilot lamp Pump Solenoid valve Ist group Solenoid valve 2nd group Automatic filling solenoid valve 10 Boiler filling pilot lamp 11 Keyboard Ist group 12 Keyboard 2nd group 13 Boiler lever sesor ll 12 11 Electrical Diagram Hand Lever EROICA L 2 230V Key 1 Main switch 2 Heating element thermal protector 3 Pressure switch 4 Heating element 5 Mains pilot lamp 6 Pump 7 Automatic filling solenoid valve 8 Boiler filling pilot lamp 9 Keyboard Ist group 10 Keyboard 2nd group 11 Boiler level sensor 10 011 www streamlinesupplies com au_ 13 STREAMLING supplies Electrical Diagram Automatic EROICA S 2 230V W Aa AZ IN RIS F 13 0 0 Key NO 1 Main switch O O Heating element J NE 4 thermal protector O _0 Pressure switch Heating element Mains pilot lamp Pump Solenoid valve Ist group Solenoid valve 2nd group Automatic filling solenoid valve 10 Boiler filling pilot lamp 11 Boiler level 12 Fl
5. au 8 STREAMLING supplies Installation Water drain vessel i l Electric Main switch supply cable Water feed Water inlet a the mains connection Water Water drain hose inlet valve Water hose Gdin Pipe from water softener to water inlet Mains switch Water filter not provided Electrical connection to the mains POSITIONING AND CONNECTIONS Before installation the Manufacturer strongly recommend to control the water supply system and the electrical connections Check the mains pressure which should not exceed 6 bar otherwise it is recommended the installation of a water pressure reducer The machine must be installed with a mains electrical switch with adequate fuses Attention the machine must be connected to an efficient earthling system yellow green cable Check the efficiency of the main drain hose part 8 Then proceed with the connection of the water drain hose to the machine part 7 Hydraulic connections water inlet 3 8 BSP water male fitting water drain hose internal 14 mm The machine must be installed on a stable surface find a good position for the water softener part 12 Connect the valve part 9 to pipe part 11 Connect the pipe to the water inlet connector part 5 Connect the pipe part 7 to the discharge recipient part 6 and then on the general discharge part 8 Put a recipient under the water softener discharge pipe and let out the water for a few min
6. connection of the appliance to the fixed installation verity if a conformity certificate has been issued to confirm the suitability of the fixed installation for this use if not inform the end user and leave the appliance disconnected Check the integrity of all components and do not install defective or damaged parts Ask for substitution Check and verify that the outlet power supply voltage is the same as shown on the rating plate of the appliance The customer has fo protect the power outlet used to supply the appliance by means of a safety switch system complying with the standards and laws in force The installation of a water softener is highly recommended Machine should not be installed with supplying water having hardness degree higher than 8 French degrees It is imperative that a suitable water filter is installed in line prior to the machine and the cartridge changed every 6 months The motor pump set must be positioned far from hydraulic pipes heat sources electrical appliances or it must by protected by a water resistant aerated enclosure When installing the appliance a multi pole main switch having contacts with opening gap equivalent or higher than 3 mm should be connected as requested by the safety standards Any unreliable cable connection is forbidden The appliance must be placed over a flat and stable surface leaving a minimum clearance of 30 mm from walls www streamlinesupplies com
7. STREAMLING supplies Operating INSTrUCTIONS Streamline Supplies 9 Joseph Baldwin Place Shepparton Victoria 3630 Ph 03 5831 5555 Fax 03 5821 3633 www streamlinesupplies com dau 1 STREAMLING supplies Introduction Please read this technical handbook carefully as if provides important information on the correct installation use and maintenance Keep this handbook in a safe place for further consultation The Manufacturer is not responsible for any damage caused by incorrect or unreasonable use and maintenance The Manufacturer accepts no responsibility for damage to persons or objects caused by incorrect installation The instructions in this handbook are in no way a substitute for the safety instructions and technical data on the machine or the packaging concerning installation and function This handbook is an essential part of the machine For further information or additional handbooks please contact your distributor or the manufacturer This handbook reflects the current manufacturing requirements and is subject to change according to future modifications The Manufacturer is free to modify this manual without updating previous editions except in exceptional cases This machine is to be operated according to the instructions supplied in the handbook by a responsible adult operator installation and or service technician www streamlinesupplies com au 2 Instructions for use STREAMLING supplies
8. TREAMLING supplies Warranty Conditions The warranty period is 12 months trom the installation effected by an authorized la SCALA technician and covers the faulty parts only Not included are transport costs and labour cost Cannot be considered under our responsibility non installation of in line water filter periodic change of water filter damage in transit damage due to incorrect installation or maintenance periodic regeneration of water softener not effected problems caused from the electric and hydraulic supplies of the client installation by non authorized persons non genuine parts seals filters gutters etc Not included in the warranty conditions are incorrect use of the machine and non observance of the maintenance and technical handbook For no reason can the buyer delay or suspend the payment agreed this forfeits all rights and the guarantee Streamline Supplies 9 Joseph Baldwin Place Shepparton Victoria 3630 Ph 03 5831 5555 Fax 03 5821 3633 www streamlinesupplies com au 16
9. e other has to be completed within 30 seconds otherwise the memory will be lost For partial keyboard dose setting push star key again after the last selected dose key has been programmed REE lt Function of the machine The main components of the espresso coffee machine are the following BOILER Contains hot water and steam COFFEE DELIVERY GROUP AND HEAT EXCHANGERS This is The Component where the filter holder is inserted The hot water enters the delivery group where the processes of pre infusion Infusion and delivery of the coffee take place The machine comes with one heat exchanger for each delivery group The heat exchanger is fitted in the boiler and It s purpose is to heat up the fresh water coming from the mains to the correct temperature HEATING SOURCE An electric element warms the water in the boiler ELECTRIC PUMP This component is to increase the water pressure of the mains to the correct water pressure needed for espresso coffee preparation which is 9 bars STEAM WAND This wand delivers hot steam for milk frothing and steaming of drinks in jugs tea chocolates etc Electric Diagram STREAMLING supplies HOT WATER TAP This delivers hot water CONTROL amp MONITORING DEVICES Pressure gauge Indicates the boiler pressure and the working pressure of the pump Pressure switch This is used to keep the boiler water temperature constant by controlling the heating elements based
10. ine detergent in the blind filter and then inserting it into the group Press the button for semi automatic working and wait about 30 seconds Push this button again to stop Repeat this operation for 3 to 4 times Remove blind filter and replace it with the regular filter continue rinsing Finally prepare one coffee to remove residual detergent taste Turn the machine off prior to proceeding to the following operations Clean the drip tray and grid Clean the plastic recipient located in the part under the drip tray Use a spoon for this purpose Clean the body work with a non abrasive damp cloth Never use aggressive products or alcohol Periodic regeneration of water softener Streamline Supplies Recommends the use of GRUPPO i LENE www streamlinesupplies com au_ H STREAMLINE supplies Key A Boiler B Heat exchange 1 Water circuit feeding pipe 13 2 PUMp 3 Boiler water Filling Solenoid valve Non return Valve Exapansion valve Water Discharge Vessel Coffee delivery group Pump boiler Steam valve 10 Water valve 11 Secruity valve 12 Delivery group solenoid valve 13 Pressure switch i 4 O OONA MSA Key A Boiler Heat exchange Water circuit feeding pipe Pump Boiler water filling Solenoid valve Non return valve Expansion valve Water discharge vessel Coffee delivery group Pump boiler pressure guage Steam valve 10 Water valve 11
11. nnot be controlled or foreseen Therefore it s absolutely necessary to evaluate all remaining risks and to care about the following suggestions This machine is safe only if appropriately connected to an efficient grounding system complying with the safety standards in force the Country where the machine will be installed The Manufacturer rejects any responsibility for accidents due to the missed application of the above standards since a wrong installation may result in injuries to persons as well as other problems that may affect other areas Do not leave packing items such as plastic bags Styrofoam nails etc around because children or other persons could get injured Any defect or discrepancy has to be notified immediately to the persons authorized for installation and maintenance of the machine Machine installation has to be performed exclusively by authorized and qualified technicians Authorized service if the service is not complying with the instruction of the Manufacturer or is components other than those recommended by the Manufacturer will be Used for installation or maintenance of the appliance the conformity declaration of the product will be voided and so the Manufacturer s responsibility Possible replacement of the supply cable if damaged must be performed immediately and exclusively by service staff qualified or authorized by the Manufacturer in order to prevent any danger to persons Before the
12. noid valve for automatic water filling is blocked 1 Replace motor 2 Replace heat exchanger 3 Re place solenoid valve water leakages on table top 1 Exhaust basin is dirty 2 Exhaust pipe is disconnected or clogged 1 Clean exhaust basin 2 Replace exhaust pipe Coffee dregs are wet 1 Coffee grinding is too fine 2 Group Is still cold 3 Group solenoid valve doesn t work properly 1 Adjust grinding degree 2 Wait for appliance to get warm 3 Clean group exhaust system Coffee delivery is too slow 1 Coffee grinding is too fine 2 Filter holder is dirty 3 Group is clogged 4 Injector or solenoid valve are par tially clogged 1 Adjust grinding degree 2 Replace filter and clean filter holder more frequently 3 Contact service 4 Replace injector or solenoid valve Coffee delivery is too fast 1 Coffee grinding is too rough 1 Adjust grinding degree Delivered coffee is cold 1 Heat exchangers or heating ele ment coated with limestone 2 Pres sure switch contacts are oxidised 3 Defective electrical connections 4 Heating element is partially burned 1 Contact service for overhauling 2 Clean pressure switch contacts 3 Contact service to check the connections 4 Replace heating element Delivered coffee is too hot 1 Wrong pressure switch calibration 1 Adjust pressure switch by acting on the relevant screw www streamlinesupplies com au 15 S
13. on the boiler pressure Automatic Boiler Water Level Control Electronic circuitry used to the boiler water level constant HYDRAULIC CIRCUIT The hydraulic diagram shows that the water used for the preparation of coffee comes directly from the mains and is heated in the heat exchangers inside the boiler The machine is connected to the electric mains by a supply cable As shown on the electric diagram there are two circuits A feeding circuit for electric components solenoid valves pump motor electronic control panel A feeding circuit for the heating element ATTENTION In all cases this appliance must be connected to a 3 pin power point or a hard wired direct wired power source The use of extension leads or loose type connectors Is strictly forbidden and unlawful www streamlinesupplies com au 6 STREAMLING supplies Main Switch The machine is equipped with a main power supply switch with 3 positions Pos 0 No power supply to internal components Pos 1 Power supply to function components l Pos 2 Power supply to f functional components and electric boiler heating elements www streamlinesupplies com au 7 STREAMLING supplies Installation Warnings Please read carefully The Manufacturer has tried to foresee all possible safety requirements to ensure the safety of users Anyhow different conditions of installation or of equipment moving can cause situations which ca
14. ow rate sensor Ist group 13 Flow rate sensor 2nd group 14 Keyboard Ist group 15 Keyboard 2nd group 16 Keyboard 3rd group 17 Keyboard 4th group 0 CONAN A W www streamlinesupplies com au 14 STREAMLING supplies FR FAAALIA If D e fa 4 BB Y a AN AUD EEN a mM d i a VAN h WU L W A EJ aD amp e l 4 4 CA i AN K I hk GD JIN aL sLU LO A AA EN A si the appliance dosen t switch ON 1 main switch id off 2 appliance switch if off 3 wrong connection to mains 1 set main switch in on 2 set appliance switch in pos 1 3 contact service for check missing hot water in boiler 1 water source tap closed 2 pump filter clogged 3 motor oump set failure 1 open water source tap 2 replace filter 3 contact service missing coffee delivery from group 1 water source tap closed 2 motor oump set failure 3 clogged giggler 4 electronic control unit fuse melt 5 group solenoid valve failure 1 Open water source tap 2 Contact service 3 Contact service 4 Contact service 5 Contact service missing steam from lances 1 Too much water in boiler 2 Heating element failure 3 Sprayer clogged 4 Heating element protector trip 1 See SPECIFIC TROUBLE 2 Contact service 3 Clean sprayer 4 Reset protector water level in boiler is Too high 1 The pump motor always run 2 Heat exchange Is perforated 3 Sole
15. utes to clean the resin Effect the electric connection between the feeding part 3 and the switch part 2 www streamlinesupplies com au 9 Start up Turn the main switch fo pos 1 The filling process will proceed automatically When the boiler is filled turn the Main switch to pos 2 to activate the heating element s electrical feed Wait until boiler pressure reaches maximum working pressure approx bar Open steam valve for a few seconds Be sure Boiler pressure reaches approx 1 bar after releasing steam valve Prepare one dose of coffee As coffee flows The boiler pressure is controlled by check the correct pump pressure approx a pressure switch Turn screw A for 9 bar on the pump pressure gauge Pump boiler pressure adjustment pressure can be adjusted using the screw A positioned on the pump s by pass A Recommended working data of the machine Pump pressure 9 Bar Boiler pressure Bar Opening pressure of boiler Security valve 1 5 Bar Expansion valve opening Pressure 11 Bar COFFEE DOSE Setting on Automatic Model Hold the star key pos 1 pressed until all LED s are switched on the keyboard group on the left Put filter holder with perfectly ground dosed coffee in the group Place the cup for which you want fo set the dose under the coffee group Push the key related to the selected dose and push if again when the correct quantity of coffee is reached Repeat this for dose setting of each key
16. y The machine must operate only with drinking water The machine has to be switched off whenever unattended from the operator Tea and coffee cups must be carefully drained before placing them over the Cup tray www streamlinesupplies com au 3 STREAMLINE supplies Espresso Coffee Machine Range Lever Esoresso coffee machine with lever operated manual dosing control Automatic water boiler refill is standard Built in volumetric pump Machine available with 2 groups Semi Automatic Esoresso coffee machine with switch operated manual dosing control Automatic water boiler refill is standard Built in volumetric pUMP with motor Machine available with 2 Qroups Automatic Esoresso coffee machine with microprocessor controlled volumetric dosing control amp programming via digital keyboard Automatic boiler water refill is standard Built in volumetric puMp with motor Machine available with 2 groups www streamlinesupplies com au 4 Description of External Components Keyboard for Coffee Delivery Service Hot Water trol knob Stream Control kno Control Knob Boiler Pressure Gauge Mains Pilot Lamp Main Switch Boiler Water Level Indicator Steam Wand Push Button Panel keyboard for Coffe Delivery Service Ranging from left to right Ristretto Espresso Two Ristrettos Two Espressos Manual Delivery The programming operation between a key and th
Download Pdf Manuals
Related Search