CRUISE CONTROL OPERATING INSTRUCTIONS
Contents
1. A SCRU SE CRUISE CONTROL OPERATING INSTRUCTION CONGRATULATIONS You have purchased one of the most advanced cruise controls in the world today It has more operating features and superior performance than any other unit available Take the time to read and understand these instructions and benefit from all of the new AUSCRUISE Cruise Control system features As with any cruise control it will allow the vehicle to maintain a constant speed during most normal driving conditions without keeping your foot on the accelerator pedal and with the addition of our unigue features Optional Features on Some Models Multiple Pre Set Resume Speeds Over Speed Warning and Clutch Coast Resume will add to the drivers comfort and possibly improve your fuel economy The minimum speed at which your AUSCRUISE Cruise Control will operate is between 30 and 40 KPH TO ENGAGE CRUISE CONTROL Operate the ON OFF svvitch On some models of svvitches the LED indicator on the svvitch or dash will light up Green This indicates the Cruise Control is ON and ready to be activated Accelerate the vehicle to the desired speed operate the SET svvitch the LED indicator on the switch or dash will change colour to Orange to indicate the Cruise Control is Engaged Remove your foot from the accelerator pedal The vehicle will now maintain this speed until changed or the Cruise Control is disengaged Under certain circumstance2. art vehicle and depress any of the Multi Resume Control Switch buttons e Cancel any Cruise Control resume speed or over speed alert setting that may be active With the ON OFF switch in the OFF position Drive to the exact desired speed press and hold the SET switch until the engage indicator starts flashing Around 10 seconds Press the svvitch on your Multi Resume Control Svvitch you vvish to program for this e The engage indicator will stop flashing and remain constantly on to indicate programming has been successful Follow the same sequence to program your remaining Multi Over speed settings The speeds you set for Multi Over speed vvill remain until you change them even after you turn off your ignition and are totally independent to the speeds you set for your Multi Speed speeds NOTE You may reprogram any or all switches as often as you like OCopyright 2014 CHARGE PLUS
3. e the vehicles speed by 1 KPH per tap TO DECREASE CRUISE CONTROL SPEED Press and hold the DEC switch This will gradually decrease the vehicles speed until released which will now be the cruise speed Or use the Tap down feature by tapping the DEC switch this will decrease the vehicles speed by 1 KPH per tap TO RESUME CRUISE CONTROL SPEED If the Cruise Control has been disengaged by any of the features listed simply press the RES switch and the vehicle will gradually increase in speed until it has reached the previously set speed The vehicle must be above 30 40 KPH NOTE The Cruise Control will RESUME even after the vehicles ignition has been turned OFF This is a unique feature to the AUSCRUISE Cruise Control If you do not wish to have this feature some models of cruise controls can have this feature turned off by re programming the module Consult your dealer installer Programming fee may apply VVARNING Do not use the Cruise Control vvhen road or driving conditions could require varying speed A constant speed may not be practical in heavy or varying traffic or on vvinding slippery or rough roads Keep the main svvitch in the OFF position unless using the crulse control VVith manual transmissions never attempt to move the gear lever vvithout using the clutch pedal vvhile the Cruise Control is maintaining vehicle speed Engine over revving and damage may result unless clutch operated Coast Resume is opt
4. ioned Remember that taking your foot off the accelerator when the Cruise Control is engaged will not reduce vehicle speed When going up or dovvn hills particularly when tovving it is possible for the vehicle to gain or lose speed even though the Cruise Control is engaged If this happens vvhile going up hill merely depress the accelerator pedal to maintain the speed desired If going dovvn hill steep enough to cause the vehicle to gain speed depress the brake pedal vvhich vvill both disengage the Cruise Control and slovv the vehicle dovvn If a malfunction has developed in the Cruise Control system have the system checked and corrected as soon as possible by a authorised dealer OPTIONAL FEATURES Your AUSCRUISE Cruise Control may be eguipped with one or more of the following optional features consult the Program amp Warranty pages in the back of this manual for information CLUTCH OPERATED COAST RESUME This is a unique feature to AUSCRUISE Cruise Control s Professional series of cruise controls and is available as an option on some models when fitted to manual transmission vehicles Follovving is a description of the function e Depressing of the clutch while the Cruise Control is engaged will cause the Cruise Control to Coast Release the throttle to idle the Engage indicator vvill change from being on constant to fast flashing this is to indicate to the driver that Coast Resume mode is active you can n
5. is function turn the ON OFF switch to the OFF position and drive to the desired Over speed speed and press the SET switch The LED indicator on the switch or dash will come on Red to indicate Over Speed mode is active If your road speed increases 5 KPH above the Over Speed set speed the LED will fast flash and there will be 4 beeps from the warning buzzer The LED will continue to flash while you are in excess of 2 5 KPH above the set speed the buzzer will not beep again until you slow to within 2 5 KPH of the set speed and then go over speed again To disable Over Speed Warning at any time turn the ON OFF switch to the ON position or ON then OFF This will disable Over Speed until you press the RES switch with the ON OFF switch in the OFF position This will reset the Over Speed warning to the previous setting or pressing SET will set in a new Over Speed speed NOTE with some control switches the Resume to previous set over speed speed function is not possible because the design of the switch does not allow you to operate the RES function with the ON OFF switch in the OFF position MULTIPLE PRE SET OVER SPEED SPEEDS When you option Multi Resume with the AUSCRUISE Cruise Control s Professional series of cruise controls you can also option Multi Over speed To program your Multi Over speed preset speeds follow the following sequence e St
6. ow change gears without over revving your engine after changing gears vvhen you release the clutch the Cruise Control vvill automatically Resume to the previously set speed and the Engage indicator will return to constant on f you hold the clutch pedal dovvn for over 10 seconds the Cruise Control Microprocessor will assume you have an emergency and will disengage the Cruise Control the Clutch Coast Resume function will be cancelled and you will need to operate the Resume switch to go back to your Set speed e In the event you need to cancel the Cruise Control pressing the brake at any time will do this and override the Coast Resume feature until the next time you re engage the Cruise Control MULTIPLE PRE SET RESUME SPEED This is a unique feature to AUSCRUISE Cruise Control Professional series of cruise controls By the addition of an extra control switch there is currently a dash mount and a steering wheel mount svvitch available you can have up to an aditional 3 svvitches upon vvhich you can have predetermined resume speeds which you can use to control the Cruise Control set speed PROGRAMMING To program your Multi Resume preset speeds follovv these instructions e Start vehicle and depress any of the Multi Resume Control Switch buttons e Cancel any Cruise Control resume speed or over speed alert setting that may be active e With the ON OFF switch in the ON position e Drive
7. s your Cruise Control may not be able to maintain your desired set speed if you are driving up steep grades or pulling a trailer If you wish to increase the vehicle speed or pass another vehicle press down on the accelerator pedal When you take your foot off the accelerator pedal the vehicle will slow down to the previously set speed this may not be the case if you have increased the vehicle speed by more than 5096 above the set speed On some models of control switch the LED indicator may stay on after ignition is turned off The indicator LED vvill turn off automatically after a short time DISENGAGING THE CRUISE CONTROL e Press the brake pedal Turn the ON OFF switch to the OFF position e If the vehicle has a manual transmission the Cruise Control will disengage when the clutch pedal is pressed Refer Optional clutch Coast Resume function If the vehicle is automatic and the Neutral Cancel feature has been fitted the Cruise Control vvill disengage vvhen the selector lever is shifted to the Neutral position NOTE This feature is not available on some vehicles If the vehicle speed increases to 5096 above the set speed or drops belovv the minimum engage speed TO INCREASE CRUISE CONTROL SPEED Press and hold the ACC switch This will gradually increase the vehicles speed until released which will now be the cruise speed Or use the Tap up feature by tapping the ACC switch this will increas
8. to the desired speed Press and hold the SET switch until the engage indicator starts flashing Around 10 seconds e Using the Tap up and Tap down functions you can adjust the Cruise Control to the desired speed you wish to store e Press the switch on your Multi Resume Control Switch you wish to program with the selected speed e The engage indicator will stop flashing and remain constantly on to indicate programming has been successful e Follow the same sequence for the remaining Multi Resume switch buttons e The speeds you set in your Multi Resume buttons will not change even after you turn off your ignition NOTE You may program any or all switches as often as desired OPERATION You can use the Multiple Pre Set Resume function at any time you must be above 30 40 KPH either with the Cruise Control Engaged or Disengaged by pressing the desired Multi Resume speed switch The Cruise Control will Accelerate or Decelerate to the speed set to that switch If you disengage the Crulse Control and vvish to return to the same set speed this is done by using the normal RES switch You only need to use the Multi Resume svvitches when you wish to change your set speed to one of the presets OVER SPEED VVARNING Having this feature integrated into a Cruise Control is Unique to AUSCRUISE Cruise Control s Professional series and is available as an option on selected models ask your dealer installer if it is available To activate th
Download Pdf Manuals
Related Search