Limits Operating Instructions Product Registration Form
Contents
1. Sensor module empty Please check the sensor module System error Please send the breathalyser back to the supplier for repair Push the hook towards the right to extend the personal mouthpiece for testing AUSTRALIAN BLOOD ALCOHOL LIMITS Adult License 0 05 Some drivers are restricted to lower levels of BAC Please refer to your local transport authority for your correct limit If in any doubt do not drink and drive The safest level when driving is none at all Alcohol impairs your judgement and can make you drowsy or sleepy Disclaimer PLEASE NOTE This product must be used in accordance with the instructions in this manual and in particular must not be allowed to get wet This product is intended to provide the user with an indication of alcohol on the breath However neither the manufacturer nor the supplier gives any warranty express or implied that the product can give any indication of blood alcohol level Aperson s BAC Blood Alcohol Concentration can only be accurately measured by the administration of a blood test This product only measures breath alcohol content which in turn only gives an approximately indication of blood alcohol concentration In these circumstances the user of this product should not rely on the information provided thereby as an accurate indication of his blood alcohol concentration or of his level of intoxication or of his fitness to drive and in particular should not take any a2. sensor to measure breath alcohol levels Depending upon the amount of alcohol registered by the sensor after a period of time it will require recalibration Andatech recommends the AlcoSense Zenith is calibrated every 6 months or after 500 uses AlcoSense 7A an a a a a Fuel Cell Breathalyser FXCELL anad KEKE AlcoSense ZENITH w Alcosense com au calibrate is a central location where you can register your warranty sign up to recieve calibration reminders and schedule calibrations Once you have registered you can add as many AlcoSense products as needed to that account If you prefer the old fashioned method of product registration complete this form and forward to Andatech Corporation Pty Ltd PO BOX 3038 Nunawading VIC 3131 Australia Place of Purchase Surname AlcoSense andatech
3. Mouthpiece Slot Digital LCD Display Personal mouthpiece Power Button Battery amp sensor module cover Groove for Mouthpiece opening cover Contents Breathalyser hardcase mouthpieces x5 AAA batteries x2 pouch and user s manual 8 0 XO Od py q uolesoduoyg ydajyepuy 0 PUPEMIO pue WO SIY 8 a dWOd 10 enessny LELE DIA Sulpemeuny 9 e1q1 e9 Ne Wod asuasoz e MMM je UNUO Ja siHay Specifications uoleijsibay yNpoid Indication of BAC 0 000 to 0 4000 BAC Accuracy 0 005 at 0 050 BAC Warm up Time 5 seconds 4 minutes Response Time Within 10 seconds at 0 10 BAC Use mouthpiece Only compatible with AlcoSense mouthpieces Sensor Type Fuel Cell Sensor Power Supply 2 x AAA alkaline batteries Weight 85g including batteries Dimensions mm 105 high x 50 wide x 15 deep Calibration Recommended every 6 months or 500 tests Ambient Conditions Operations 5 40 C Storage 0 50 C ow when you are drinking you can be more aware of your alcohol level before you get into the car and possibly drive dangerously We hope you enjoy owning your AlcoSense Zenith breathalyser If you have any questions regarding the unit or want to speak with us further please visit alcosense com au or call 1300 800 200 between 9am and 5pm Monday to Friday Operating Instructions Step 1 Remove the battery cover by pushing up the groove at the bottom S
4. ction in reliance on such information as the product can provide no more than an indication of alcohol on the breath If the user of this product makes any decision or takes any action based on the use of the product such decision or such action shall be at the sole risk of the user and neither the manufacturer nor the supplier assumes any responsibility for such decision or action In particular neither the manufacturer nor the supplier shall be in any way liable if the user of the product asserts that the product led him to believe that he was fit to operate a motor vehicle and is subsequently found not to be so fit This product is certified pursuant to Australian Standard AS 3547 as a type 2 hand held qualitative device Warranty The manufacturer warrants for 3 years from the date of purchase the product to be free from defects in workmanship or material excluding recalibration under normal use The manufacturer s obligation under this warranty is limited to replacing adjusting or repairing the unit if returned along with proof of purchase This warranty is void if the unit has been tampered with damaged or abused in any way Allow at least 20 minutes after eating or drinking before testing Any type of alcohol remaining in the mouth of saliva may interfere with proper testing and requires about 20 minutes to disperse This includes alcohol based mouthwash or similar products Avoid testing in high wind conditions or in poorly v
5. entilated or enclosed spaces Poor ventilation may also lengthen the time required for warm up between tests Do not blow smoke saliva or other contaminants into the mouthpiece as the sensor may become damaged Wait at least 20 minutes after smoking before conducting a test Do not use the breathalyser as a tool to drink and drive Do not blow fluid into the instrument as it will damage the sensor and void your warranty Do not store in an extreme environment where high temperature or high humidity exists Keep out of the reach of children To maintain accuracy we recommend professional recalibration every 6 months Blood alcohol concentration can continue to rise for up to 2 hours after the cessation of drinking If a caution result or a result is close to the designated BAC it is recommended to wait and retest after 20 minutes It can take 10 hours or more for the alcohol level to return to a zero after a high blood alcohol level has been reached A further test should be carried out later in the day of the following morning User serviceable batteries safety Do not dispose of batteries in a fire Do not recharge a battery unless it is specifically marked rechargeable Do not expose Zenith or batteries to heat source Do not mix old and new batteries or mix different types or makes of batteries Do not allow children to play with the batteries Recalibration amp Service The AlcoSense Zenith uses a fuel cell
6. tep 2 Remove the batteries from the unit Step 3 Grab the handles and pull down the side indicated on the sensor Press the power button to switch on the breathalyser module case The breathalyser will warm up until it shows the blow sign Step 4 Remove the sensor module and replace with a new one Blow into the mouthpiece in the breathalyser for 4 seconds or until you Please note hear the unit click Do not lift up the sensor module before pulling it all the way down The final BAC result will be displayed on the screen for 15 seconds Before using a new sensor please remove the cap on the hose To take another breath test wait at least 3 seconds from when the test result showed up then press the power button again before blowing into Warning display the mouthpiece Please note Flow The breathalyser will automatically switch off after 4 minutes of inactivity If you press and hold the power button you will be able to check the accumulated total test counts and view the last breath test result The breath sample was not strong enough to detect a reading After warm up please blow strong and steadily into the mouthpiece The battery power is low Please replace the batteries with new alkaline batteries If you test over 1000 tests the Zenith Plus will display the CAL sign for 3 Personal mouthpiece seconds before warming up The CAL sign will provide the appropriate time a5 3 for calibration or replacing the sensor module
Download Pdf Manuals
Related Search