Manual - AGG Doors
Contents
1. PZ INSTALL THE PROTECTOR SYSTEM See accessories Install this accessory for all installations on tilt doors doors over 2 5m and when the closing force as measured on the bottom of the door is over 400N 40kg After opener has been installed and adjusted the Protector System accessory can be installed SAFETY FIRST Instructions are included with this accessory Whilst Chamberlain have engineered safety features into your The Protector System provides an additional garage door opener we urge you to consider fitting IR Beams measure of safety against a small child or obstacle ito your new garage door opener In many countries these being caught under a garage door It uses an __ idevices are compulsory to prevent serious injury or property invisible beam which when broken by an obstruction idamage For your own peace of mind and the safety of others causes a closing door to open and prevents an open please install this inexpensive safety device i door from closing and is strongly recommended for i homeowners with young children Note The opener will automatically detect the Protector System when it is installed and operating for 5 minutes during this time the beams must remain unobstructed The opener will not close unless the beams are aligned white black Connecting the Protector System wires twisted together Locate the terminals on the front of the opener Strip all w2. Repeat safety reverse test after any adjustment of door arm length close force or down limit 9 Door opens but won t close e Check the Protector System if you have installed this accessory If the light is flashing correct alignment If opener light does not flash and it is a new installation repeat setting the limit and force sections 21 and 22 e Repeat the safety reverse test after the adjustment is complete 10 Opener light does not turn on e Replace light bulb 24V 21W maximum 11 Opener strains e Door may be unbalanced or springs are broken Close door and use manual release rope and handle to disconnect trolley Open and close door manually A properly balanced door will stay in any point of travel while being supported entirely by its springs If it does not call for professional garage door service to correct the problem 17 12 Opener motor hums briefly then won t work e Garage door springs are broken SEE ABOVE If problem occurs on first operation of opener door is locked Disable door lock e Repeat safety reverse test after adjustment is complete 13 Opener won t activate due to power failure e Pull manual release rope and handle down and back to disconnect trolley Door can be opened and closed manually When the power is restored pull the manual release handle straight down The next time the opener is activated the trolley will reconnect e The outside quick release accessory if fitted
3. The door must travel through a complete cycle UP and DOWN in order for the force to be set properly If the unit cannot open and close your door fully inspect your door to ensure that it is balanced properly and is not sticking or binding The force MUST be learned in order to properly complete the setting of the limits 23 TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important The garage door must reverse on contact with a 40mm A obstacle laid flat on the floor Failure to properly adjust opener may result in serious personal injury from a closing garage door Procedure Place a 40mm obstacle 1 laid flat on the floor under the garage door Operate the door in the down direction The door must reverse upon contact with the obstacle If the door stops on the obstacle remove obstacle and repeat setting the limits and force sections 21 amp 22 and repeat safety reverse test When the door reverses on the 40mm obstacle remove the obstacle and run the opener through a complete travel cycle Door must not reverse in closed position If it does repeat setting the limits and force sections 21 amp 22 and repeat safety reverse test Repeat test once a month and adjust as needed
4. Align bolt holes on brackets 6 with bolt holes on opener Secure brackets to opener with the bolt previously removed Tighten bolts securely The opener sprocket teeth must engage the belt AUTION Use only those bolts mounted in the top of opener Use of any ther bolts will cause serious damage to opener 10 ATTACH SPROCKET COVER Place sprocket cover 1 on top of the opener 2 secure with screws 3 Insert bolt 4 into trolley stop hole 5 secure with washer 6 and nut 7 11 INSTALL HEADER SLEEVE AND TIGHTEN BELT Slide header sleeve 1 onto rail 5 Slide flat washer 3 spring 2 and washer 3 onto carriage bolt 4 Thread nut 6 onto carriage bolt until finger tight Use an open end wrench 7 to tighten nut until the belt is approximately 2mm above the base of the rail at its midpoint DO NOT OVER TIGHTEN THE BELT See image INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury Disengage all existing garage door locks to avoid damage to the garage door To avoid serious personal injury from entanglement remove all ropes connected to the garage door before installing the opener NOTE Where possible it is recommended that the opener be installed 2 1m 7 feet or more above the floor 12 POSITION THE HEADER BRACKET The header bracket must be securely fastened to a structural support of the garage Reinforce the wall or ceiling with
5. disconnects the trolley from outside the garage in case of power failure 14 Setting the limits manually 1 Press and hold the black button until the yellow indicator light starts flashing slowly then release 2 Push and hold the black button until the door reaches the desired UP open position Adjust the position of the door by using the black and orange buttons Black moves the door UP open and orange moves the door DOWN close Check to be sure the door opens high enough for your vehicle 3 Push the remote control or door control This sets the UP open limit and begins closing the door Immediately press either the orange or the black button The door will stop Adjust the desired DOWN closed limit by using the orange DOWN and black UP buttons Check to be sure the door is fully closed without applying excessive pressure on the rail rail should not bow upwards and the belt should not sag or droop below the rail Push the remote control or door control This sets the DOWN close limit and begins opening the door NOTE If neither the BLACK or the ORANGE button is pressed the door will reverse off the floor and the DOWN travel limit will be set automatically 4 Open and close the door with the remote control or door control 2 or 3 times If the door does not stop in the desired UP open position or reverses before the door stops at the DOWN close position repeat setting the limits manually one more time e
6. If the door stops in both the desired UP open and DOWN close positions proceed to test the safety reversal system OPERATION OF YOUR OPENER Your opener can be activated by any of the following devices The backlit door control button if installed Hold the button down until door starts to move The outside keyswitch or keyless entry system if you have installed either of these accessories The remote control transmitter Hold the push button down until the door starts to move Opening the door manually springs could allow an open door to fall rapidly Property Door should be fully closed if possible Weak or broken damage or serious personal injury could result The door can be opened manually by pulling the release handle down To reconnect the door pull the release handle down and toward the opener Do not use the manual release handle to pull the door open or closed When the opener is activated by remote control or backlit door control button If open the door will close If closed the door will open If closing the door will stop If opening the door will stop allowing space for entry and exit of pets and for fresh air If the door has been stopped in a partially open or closed position it will reverse direction If an obstruction is encountered while closing the door will reverse If an obstruction is encountered while opening the door will reverse then stop The op
7. UP open limit and begins closing the door Immediately press either the orange or the black button The door will stop Adjust the desired DOWN close limit position using the black and orange buttons Check to be sure the door is fully closed without applying excessive pressure on the rail rail should not bow upwards and the belt should not sag or droop below the rail Push the remote control or door control This sets the DOWN close limit and begins opening the door Open and close the door with the remote control or door control 2 or 3 times leave door in open position ready for force setting NOTE The force must now be set in order to complete your installation refer section 22 22 SETTING THE FORCE The force setting button is located behind the light lens of the opener The force setting regulates the amount of power required to open and close the door 1 Open the light lens Locate the orange button 2 2 Push the orange button 2 twice to enter unit into force adjustment mode The LED 3 indicator light will flash quickly 3 Push the programmed remote control 4 or push bar on the door control if installed The door will travel to the DOWN close position Push the remote control 4 again the door will travel to the UP open position The LED 3 indicator light will stop flashing when the force has been learned
8. not position the opener more than 50mm 2 above this point Header 50mm 2 Bracket above the highest point of travel 50mm spacer should be used to determine the correct mounting position 50mm 2 above the highest point of travel Header Bracket 50mm spacer should be used to determine the correct mounting position Bear race 200mm 8 above the highest point of travel 100mm spacer should Door be used to determine the correct mounting position ID HANG THE OPENER The opener must be securely fastened to a structural support of the garage Three representative installations are shown Yours may be different Hanging brackets 1 should be angled Figure A to provide rigid support On finished ceilings Figure B attach a sturdy metal bracket not supplied 4 to a structural rar before installing the opener For concrete ceiling mount Figure C use concrete anchors 5 provided On each side of opener measure the distance from the opener to the structural support or ceiling Cut both pieces of the hanging bracket to required lengths Flatten one end of each bracket and bend or twist to fit the fastening angles Do not bend at the bracket holes Drill 4 5mm 3 16 pilot holes in the structural supports or ceiling Attach brackets to supports with wood screws 2 Lift opener and fasten to aama brackets with screw lock washer and nut 3 Check to make sure
9. power on the light will turn on and remain lit for 2 1 2 minutes After 2 1 2 minutes it will turn off To close gently push diffuser up until engaged 19 FASTEN DOOR BRACKET Sectional and one piece door installation procedure Door bracket 1 has left and right side fastening holes If your installation requires top and bottom fastening holes use both the door bracket and door bracket plate 2 as shown 1 Centre door bracket with or without door bracket plate as required at the top inside face of door as shown Mark holes A One piece doors Locate bracket at inside face of the door 0 100mm down B Sectional doors a 150 250mm below the top of the door f 2 Fasten bracket to the door using the appropriate screws A Wooden doors 1 Drill 8mm holes 5 16 and fasten the door bracket with A 0 100mm nut lock washer and carriage bolt 3 eid el B Sheet metal doors Fasten with metal screws 4 C One piece door optional Fasten with wood or metal screws 4 H ASSEMBLE DOOR ARM A ONE PIECE DOOR INSTALLATION Fasten the straight 1 and curved 2 door arm sections together to the longest possible length with a 2 or 3 hole overlap using carriage bolts 3 lock washers 4 and hex nuts 5 With the door closed connect the straight door arm section 1 to the door bracket with clevis pin 6 Secure with ring fastener 7 Disconnect the inner and outer trolley Slide the outer trolley
10. rail is centred over the door REMOVE 50mm or 100mm board Operate door manually If door hits the rail raise header bracket Use rail grease and lubricate bottom inside surface of rail 6 ATTACH EMERGENCY RELEASE ROPE amp HANDLE Thread one end of rope 1 through hole in top of red handle so NOTICE reads right side up as shown 3 Secure with an overhand knot 2 Knot should be at least 25mm 1 from end of the rope to prevent slipping Thread other end of rope through hole in release arm of the outer trolley 4 Adjust rope length so that handle is less than 1 8m 6 feet above the floor Secure with an overhand knot NOTE If it is necessary to cut rope heat seal cut end to prevent fraying Door should be released in the closed position if possible To release the trolley PULL down on the red handle To re engage PULL the red handle back towards the opener trolley will re engage automatically when operated DO NOT USE THE HANDLE TO OPEN OR CLOSE THE DOOR DO NOT DISENGAGE THE OPENER IF ANY PERSONS OR OTHER OBJECTS INCLUDING MOTOR VEHICLES ARE WITHIN THE DOORWAY The door is under significant tension and if the door has developed a fault or incorrect tension it may be unsafe and may fall rapidly EE INSTALL LIGHT Turn power off then gently pull lens 2 downward until the lens hinge is in the fully open position Do not remove the lens Install a 24V 21W maximum light bulb 1 in the socket as shown Turn
11. seconds enter a four digit personal identification number PIN of your choice on the keypad 2 then press and hold the ENTER button 3 Release the button when the opener light flashes 3 It has learned the code If the light bulb is not installed one click will be heard NOTE This method requires two people if the keyless entry is already mounted outside the garage Using the multi function door control to program A A ER Enter a four digit personal identification number PIN of your choice on the keypad then press and hold ENTER While holding the ENTER button press and hold the LIGHT button on the multi function door control Continue holding the ENTER and LIGHT buttons while you press the push bar on the multi function door control all three buttons are held Release buttons when the opener light flashes It has learned the code If the light bulb is not installed one click will be heard P Jh As Slide the cover plate Wireless fingerprint access system C379 aL up A optional accessory Full instructions are available with this accessory OhoA I Swipe finger at a Once you have enrolled your user s into the C379 slz steady speed B you can program the unit into your opener l Using the orange LEARN button Yellow LED will indicate successful swipe C 1 Press and release
12. terminal 1 4 of insulation from bell wire 4 and the white wire to WHT terminal Locate door control where the garage door is visible away from door and door hardware and out of the reach of children Mount at least 1 5 m 5 feet above the floor Serious personal injury from a moving garage door may result from misuse of opener Do not allow children to operate the door control or remote control transmitter Permanently fasten the caution label to the wall near the door control as a reminder of safe operating procedures Operation of the door control using the multi function door control Press the push bar 1 to open or close the door Press again to stop the door Light feature Press the light button 2 to turn the opener light on or off it will not control the opener light when the door is in motion If you turn it on and then activate the opener the light will remain on for 2 1 2 minutes Press again to turn it off sooner Lock feature Designed to prevent operation of the door from hand held remote controls However the door will open and close from the door control the outside keyswitch and the keyless entry accessories To activate press and hold the lock button 3 for 2 seconds The push bar light will flash as long as the lock feature is on To turn off press and hold the lock button again for 2 seconds E bar light will stop flashing The lock feature will also turn off whenever the LEARN button on th
13. to use the Unit In no event shall the Seller s liability for damages or injury arising from breach of law or contract or for negligence exceed the cost of repairing or replacing the Unit or refunding the purchase price of the Unit Under Division 2 Part V of the Trade Practices Act 1974 certain warranties and conditions Implied Terms are implied into contracts for the supply of goods or services if the goods or services are of a kind ordinarily acquired for personal domestic or household use or consumption Liability for breach of those Implied Terms cannot be excluded or limited and the limitations and exclusions above do not apply to the Implied Terms Except for the Implied Terms and the warranties set out above the Seller excludes all warranties and conditions implied by statute at law in fact or otherwise Liability New Zealand only Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees Act 1993 a all other guarantees warranties and representations in relation to the Unit or its supply are excluded to the extent that the Seller can lawfully exclude them and b under no circumstances shall the Seller be liable for consequential incidental or special damages arising in connection with the use or inability to use the Unit other than those which were reasonably foreseeable as liable to result from the failure NOTE We request that you attach your sales docket or invoice to this manual to e
14. yourself repairs or provide you with shipping instructions for a factory repair or replacement If an authorised installer installed your Unit you must call them for prompt on site service If our service centre determines that a warranty claim has been made in respect of a failure or defect arising out of any exclusion detailed below we may charge you a fee to repair and or return the Unit to you Exclusions This warranty does not cover any failure of the Unit due to 1 non compliance with the instructions regarding installation operation maintenance and testing of the Unit or of any product with which the Unit is used 2 any attempt to repair dismantle reinstall or move the Product to another location once the Product is installed by any person other than an authorised installer 3 tampering neglect abuse wear and tear accident electrical storm excessive use or conditions other than normal domestic use This warranty does not cover any problems with or relating to the garage door or garage door hardware including but not limited to the door springs door rollers door alignment or hinges any problems caused by electrical faults replacement of batteries or light bulbs or labour charges for reinstalling a repaired or replaced Units 114A4220B Liability Australia only Under no circumstances shall the Seller be liable for consequential incidental or special damages arising in connection with the use or inability
15. CHAMBERLAIN Convenience with Confidence www chamberlainanz com ML750 Sectional amp Tilt Garage Door Opener Installation and Operating Instructions Owners Copy Please keep these instructions for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY N2966 START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING Failure to comply with the following instructions may result in serious personal injury or property damage e Read and follow all instructions carefully e The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual gt gt PPD pep A Keep garage door balanced Do not let the garage door opener compensate for a binding or sticking garage door Sticking binding or unbalanced doors must be repaired before installing this opener property damage exists Do not wear rings watches or loose clothing while installing or servicing a garage door opener Frequently examine the door installation in particular cable springs and mountings for signs of wear damage or imbalance Do not use if repair or adjustment is needed since springs and hardware are under extreme tension and a fault can cause serious personal injury To avoid serious personal injury from entanglement remove all ropes chains and locks co
16. a 40mm 1 1 2 board if necessary Failure to comply may result in improper operation of safety reverse system You can attach the header bracket either to the header wall 1 or to the ceiling 3 Follow the instructions that best suit your particular requirements With the door closed mark the vertical centreline 2 of the garage door Extend line onto header wall above the door Open door to highest point of travel Draw an intersecting horizontal line 4 on header wall 50mm or 200mm above high point to provide travel clearance for top edge of the door Height depends on door type refer section 15 E INSTALL THE HEADER BRACKET NOTE Refer to vertical centre and horizontal lines created in section 12 for proper placement of header bracket A Wall mount Centre the header bracket 1 on the vertical centre line 2 with the bottom edge of the header bracket on the horizontal line 4 with the arrow pointing toward the ceiling Mark all of the header bracket holes 5 Then drill 4 5mm 3 16 pilot holes and fasten the header bracket with wood screws 3 Ceiling mount Extend vertical centre line 2 onto the ceiling Centre the header bracket 1 on the vertical mark no more than 150mm 6 from the wall Make sure the arrow is pointing towards the opener Mark all of the header bracket holes 5 Then drill 4 5mm 3 16 pilot holes and fasten the header bracket with wood screws 3 For concrete ceiling mount use conc
17. back toward the opener and join the curved arm 2 to the connector hole in the trolley 8 with clevis pin 6 It may be necessary to lift the door slightly to make the connection Secure with ring fastener 7 NOTE When setting the up limit the door should not have a backward slant in fully open position A slight backward slant 9 will cause unnecessary bucking and or jerking whilst operating the door B SECTIONAL DOOR INSTALLATION Connect according to Figure B then proceed to Section 21 Connect Electric Power TO AVOID INSTALLATION DIFFICULTIES DO NOT RUN THE GARAGE DOOR OPENER UNTIL INSTRUCTED TO DO SO Connect to properly fused and earthed power outlet 8 ADJUSTMENT SECTION 21 SETTING THE LIMITS Travel limits regulate the points at which the door will stop when moving up or down Follow the steps below to set the limits NOTE The door must be in the mid or closed position to begin setting the limits Setting the limits 1 Press and hold the black button 1 until the yellow indicator 3 light starts flashing slowly then release 2 Adjust the position of the door to the desired UP position by using the black button Black 1 moves the door UP open and orange 2 moves the door DOWN close Check to be sure the door opens high enough for your vehicle to pass under Push the remote control or door control This sets the
18. ccessories Any new remotes must be programmed into the opener Remote control battery If transmission range decreases replace battery To change battery To replace batteries use the visor clip or screwdriver blade to pry open the case Insert batteries positive side up To replace cover snap shut along both sides Do not dispose of the old battery with household waste Take batteries to a proper disposal centre SPECIFICATIONS Input Voltage 230 240 VAC 50Hz DC gearmotor permanent lubrication Belt with two piece trolley on steel rail Adjustable to 2 3m 127 178mm per second On when door starts off 2 1 2 minutes after stop Door Linkage Adjustable door arm Pull cord trolley release Safety Personal Push button and automatic stop in down direction Push button and automatic stop in up direction Automatic force adjustment Transformer overload protector and low voltage push button wiring Optical RPM Passpoint detector Electronic semi and fully automatic Low voltage push button circuit Electronic Electrical Limit Device Limit Adjustment Start Circuit Dimensions Length Overall 3 2m Headroom Required 30mm Hanging Weight Receiver Memory Registers Operating Frequency SPECIAL NOTE Chamberlain strongly recommends that the Protector System be installed on all garage door openers 18 CHAMBERLAIN 2 YEAR LIMITED WARRANTY Chamberlain ML750 Sectional Door Opener Chamberlain Au
19. e opener panel is activated 28 SPECIAL FEATURES A Door within a door connection Open light lens Locate auxiliary quick connect terminals remove factory installed link Insert bell wire into quick connect terminals 8 and 7 Flashing light connection me eny light can be installed anywhere Connect light leads to quick connect terminals 6 and 5 Terminal is ground OTT OTTO TOT a H ACCESSORIES r 1 Model C379 Fingerprint keyless entrypad 6 Model 845AML Multi function control panel 2 Model 84335AML 3 channel mini remote control 7 Model 75AML Illuminated button 3 Model 84330AML 1 channel remote control 8 Model 760AML Outdoor keyswitch 4 Model 8747AML keyless entry system 9 Model 1702AML or CM1702 Outside quick release 5 Model 770AML or C77 The Protector System KII REPLACEMENT PARTS SD DQ replacement batteries 229A2032 x1 or 229A2016 x2 012C0810 header sleeve 012C0777 idler assembly 041A6398 inner trolley 178B69 146A112 hanging bracket idler pin 14400077 idler pulley 041A5843 belt kit 083A0011 1 grease 041A5643 19 hardware bag 012B0905 door bracket 041A5800 outer trolley 031D0533 1 pulley cover 041A5887 C rail assembly 183D177 178B0034B straight door 012B0906 door bracket chain links 004A1008 1 2 eh I So QS 041A2828 disengagement rope a
20. function door control 1 Press and hold the button on the hand held remote that you wish to operate your garage door 2 While holding the remote button press and hold the LIGHT button on the multi function door control 3 Continue holding both buttons while you press the push bar on the multi function door control all three buttons are held 4 Release buttons when the opener light flashes It has learned the code If the light bulb is not installed one click will be heard Deleting ALL remote control codes NOTE This deletes all remotes and codes Press and hold the orange learn button on opener until the learn indicator light goes out approximately 6 seconds All previous codes are now erased Reprogram each remote or keyless entry you wish to use 26 KEYLESS DEVICE PROGRAMMING OPTIONAL ACCESSORIES Activate the opener only when door is in full view free of obstruction and properly adjusted No one A should enter or leave garage while door is in motion Do not allow children to operate push button s or remote s Do not allow children to play near the door NOTE Your new keyless entry must be programmed before it will operate your garage door opener Program the keyless entry system Using the orange LEARN button 1 Press and release the orange learn button 1 on opener The learn indicator light will glow steadily for 30 seconds 2 Within 30
21. iecinase gpa iaeei 14 REPLACEMENT PARTS 15 16 TROUBLE SHOOTING 17 CARE OF YOUR OPENER 18 MAINTENANCE OF YOUR OPENER 18 OPERATION OF YOUR OPENER 18 SPECIFICATIONS 000 18 WARRANTY ccc bebe cht eae hae 19 ay DOOR TYPES A Sectional door with curved track B One piece door with horizontal track C One piece door without track To suit doors 12 5m2 Door mass up to 70kg Door must be spring balanced EJTOoLs REQUIRED 11 13mm 2 HARDWARE PROVIDED 1 Hex bolt 2 Clevis pin 3 8mm carriage bolt 4 Wood screws 5 Sheet metal screws 6 Clevis pin 7 Rope 8 Handle 9 Wall mount for 84330AML 10 Anchor 11 Concrete anchor a o 10 2x CER LL 4 5mm 4mm u O O56 11mm 13mm 12 Lock washer 13 Hex nut 14 Ring fastener 15 Rail grease 16 Lock nut 17 Metric tapping screw 18 Hex screw 19 Spring 20 Flat washer 21 Stop bolt Uve gm 9 1x 7 BEFORE YOU BEGIN 1 Look at the wall or ceiling above the garage door The header bracket must be securely fastened to structural supports Do you have a finished ceiling in your garage If so a support bracket and additional fastening hardware not supplied may be required Do you have an access door in addition to the garage door If not Model 1702AML outside quick release accensni is required This accessory allows manual ope
22. ildren Do not allow children to operate push button s or transmitter s Serious personal injury from a closing garage door may result from misuse of the opener Permanently fasten the Warning Labels in Prominent Places adjacent to Wall Controls and manual release mechanisms as a reminder of safe operating procedures Activate opener only when the door is in full view free of obstructions and the opener is properly adjusted No one should enter or leave the garage while the door is in motion Do not allow children to play near the door or door controls Disconnect electric power to the garage door opener before making repairs or removing covers KEEP THESE INSTRUCTIONS NOTE If your garage has no service entrance door a 1702AML outside quick release must be installed This accessory allows manual operation of the garage door from outside in case of power failure CONTENTS PAGE SAFETY INSTRUCTIONS 1 DOOR TYPES siscsccctsice norn an sun ins ni Geta as 2 TOOLS REQUIRED p e trreen etenin geek 2 HARDWARE PROVIDED 2 BEFORE YOU BEGIN 3 COMPLETED INSTALLATION 3 ASSEMBEY pacis e noiire a t aae 3 5 INSTALLATION ae coineta eia 5 8 CONNECT ELECTRIC POWER 8 ADJUSTMENT a 22 22 ctescese ce age 9 10 INSTALL PROTECTOR SYSTEM 10 WIRELESS PROGRAMMING INSTALL DOOR CONTROL 13 SPECIAL FEATURES 14 ACCESSORIES is os crc
23. ires back about 10mm then twist the two white wires and the two white black wires together Trim the twisted ae wires to approximately 6mm Use a small screwdriver or white wires pen to hold down the spring terminals insert the twisted together white black wires into the grey terminal 4 then terminate the white only wires into the white terminal 3 25 WIRELESS PROGRAMMING Activate the opener only when door is in full view free of obstruction and properly adjusted No one A should enter or leave garage while door is in motion Do not allow children to operate push button s or remote s Do not allow children to play near the door The remote controls supplied with your opener are pre programmed to your receiver in the factory If you purchase additional remote controls you will need to program them into your opener using the steps below Adding remotes Using the orange LEARN button 1 Press and hold the button on the hand held remote you wish to program to the opener The learn LED will flash continuously 2 Press and release the orange learn button 3 Release the button on the hand held remote when the opener light flashes It has learned the code If the light bulb is not installed one click will be heard Using the multi
24. mbly 4 on piece of wood 5 until rail sections are flush Repeat with remaining rail sections J INSTALL THE BELT Remove belt from carton and lay out on floor do not allow belt to twist Hook the trolley connector 6 into the slot 7 on the trolley 8 INSERT TROLLEY amp IDLER PULLEY BRACKET INTO RAIL Slide idler pulley bracket m and inner trolley 2 ey5 into back opener end of rail assembly 3 be sure to insert idler pulley bracket as shown Arrow on trolley 7 must face toward front door end of rail 4 Push idler pulley bracket toward front door end of rail 4 Insert carriage bolt 5 into bolt cut out in the idler pulley bracket 6 g ATTACH TROLLEY TO RAIL To prevent the belt from fouling pull the excess to the opener end before inserting the trolley Slide outer trolley 1 into back opener end of the rail assembly 2 be sure end with trolley release arm 3 is heading in direction of opener Slide outer trolley down rail until it engages with inner trolley Move the engaged trolley assembly to the midpoint of the rail then turn the rail assembly over ready to fasten to the opener g FASTEN RAIL TO OPENER amp INSTALL BELT Remove four washered bolts 1 from top of opener Place rail 2 on opener flush with stop 3 on top of opener Wrap belt 4 over sprocket 5 Push idler pulley bracket assembly toward front of the rail to eliminate excess slack in belt
25. nable you to establish the date of purchase in the unlikely event of a service call being made Chamberlain reserves the right to change the design and specification without prior notification Some features or accessories may not be available in certain markets or areas Please check with your distributor CONTACT DETAILS Chamberlain service centres Australia Phone toll free 1800 638 234 Fax toll free 1800 888 121 New Zealand Auckland phone 09 477 2823 Phone toll free 0800 653 667 Fax toll free 0800 653 663 www chamberlainanz com Trademark of The Chamberlain Group Inc Registered Trademark of The Chamberlain Group Inc 2010 The Chamberlain Group Inc
26. nd handle 01200778 bracket 012C0855 header bracket 178B0086B curved door arm 216A206 spring tension 31 REPLACEMENT PARTS 204C0240 2 transformer and lead 1 041A0589 1 i belt pulley amp E circlip 041A5908 chasis 041A5735C logic board 041D0577 motor assembly Y 041D0538 108C0082 lens cover If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid hazard TROUBLE SHOOTING 1 Opener doesn t operate from either door control or remote e Does the opener have electric power Plug lamp into outlet If it doesn t light check the fuse box or the circuit breaker Some outlets are controlled by a wall switch e Have you disengaged all door locks Review installation instruction warnings on page 1 e Is there a build up of ice or snow under door The door may be frozen to ground Remove any obstruction The garage door spring may be broken Have it replaced 2 Opener operates from remote but not from door control Is door control button lit If not remove the bell wire from the opener terminals Short the red and white terminals by touching both terminals at the same time with a piece of wire If the opener runs check for a faulty wire connection at the door control a short under the staples or a broken wire e Are wiring connections correct Review section 27 3 Door operates from door control but
27. nnected to the garage door before installing the door opener Installation and wiring must be in compliance with your local building and electrical codes The safety reverse system test is very important Your garage door MUST reverse on contact with a 40mm obstacle placed on the floor Failure to properly adjust the opener may result in serious personal injury from a closing garage door Repeat the test once a month and make any necessary adjustments This opener should not be installed in a damp or wet space exposed to weather This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety gt PP gt These safety alert symbols mean WARNING A possible risk to personal safety or The Protector System must be used for all installations where the closing force as measured on the bottom of the door is over 400N 40kgf Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door After installation ensure that the parts of the door do not extend over public footpaths or roads Install the wireless wall control or any additional wall control in a location where the garage door is visible at a height of at least 1 5m and out of the reach of ch
28. not from remote e Replace battery if necessary e If you have two or more remotes and only one operates review wireless programming keyless device programming sections 25 and 26 e Is the door control button flashing The opener is in lock mode If you have a multi function door control push and hold the lock button for 2 seconds The door control button will stop flashing 4 Remote has short range e Is battery installed Check or change battery e Change the location of the remote control in the car A metal garage door foil backed insulation or metal siding will reduce the transmission range 5 Door reverses for no apparent reason and opener light doesn t flash e Is something obstructing the door Pull manual release handle Operate door manually If it is unbalanced or binding call for professional garage door service e Clear any ice or snow from garage floor area where garage door closes e Repeat setting limits and force see adjustment sections 21 and 22 Repeat safety reverse test after adjustment is complete 6 Door reverses for no apparent reason and opener light flashes for 5 seconds after reversing e Check the Protector System if you have installed this accessory If the light is flashing correct alignment 7 The garage door opens and closes by itself Make sure remote push button is not stuck on 8 Door stops but doesn t close completely e Repeat setting the limits see adjustment section 21
29. ration of the garage door from outside in case of power failure Complete the following test to make sure your garage door is balanced and is not sticking or binding e Lift the door about halfway Release the door If balanced it should stay in place supported entirely by its springs e Raise and lower the door to see if there is any binding or sticking If your door binds sticks or is out of balance call a trained door systems technician before proceeding with installation 4 COMPLETED INSTALLATION ALL PARTS LISTED ARE SUPPLIED IN THE CARTON As you proceed with the assembly installation and adjustment procedures in this manual you may find it helpful to refer back to this illustration of a completed installation for tilt doors for sectional doors refer section 20 1 Header sleeve 2 Idler pulley bracket 3 Trolley 4 Rail 5 Belt 6 Hanging bracket 7 Power cord 8 Opener 9 Light lens 10 Manual release rope amp handle 11 Curved door arm 12 Straight door arm 13 Door bracket and plate 14 Header bracket 15 Trolley release arm 16 Manual this document Jo it WG XG HJ ASSEMBLE THE RAIL SECTIONAL RAIL Grease inside edges of rail sections using grease 1 Place rail pieces 2 on flat surface for assembly All four rail sections are interchangeable Slide rail brace 3 onto rail section Connect rail by sliding rail brace onto next rail section Tap rail asse
30. rete anchors provided IE ATTACH RAIL TO HEADER BRACKET Position the opener on the garage floor below the header bracket Place packing material under the opener to protect the cover Raise rail until holes in the header sleeve and holes in the header bracket align Join with clevis pin 1 Insert ring fasteners 2 to secure NOTE To enable the rail to clear the sectional door springs it may be necessary to lift opener onto a temporary support The opener must either be secured to a support or held firmly in place by another person 15 POSITION THE OPENER SECTIONAL DOOR OR TRACKED TILT DOOR You will need a 50mm piece of timber or similar spacer to gauge the distance between door and rail 1 Raise the opener up onto support 2 Open the door completely place a 50mm spacer between the door and the rail as shown 3 If the top section or panel hits the trolley when you raise the door pull down on the trolley arm to disengage the motor Leave the trolley in this position until motor is fastened in place ONE PIECE TILT DOOR NON TRACKED You will need a 100mm 4 piece of timber or similar spacer to gauge the distance between door and rail Raise the opener onto support Open the door completely place a 100mm spacer between the door and the rail as shown The top of the door should be level with the top of the motor Do
31. stralia Pty Limited Chamberlain New Zealand Limited Seller warrants to the original purchaser of the Chamberlain ML750 Sectional Door Opener Unit that it is free from defects in material and or workmanship for a period of 2 years from the date of first purchase from the Seller Please retain your proof of purchase in the unlikely event you require warranty service If during the limited warranty period the Unit fails due to defects in materials or workmanship Chamberlain will provided the defective part or Unit is returned freight and insurance prepaid and well packaged to the nearest Chamberlain office or authorised installer undertake to repair or at its option replace any defective part or Unit and return it to the Buyer at no cost Repairs and replacement parts are warranted for the remaining portion of the original warranty period Limited warranty on opener Chamberlain will furnish a replacement opener free of charge if it is found to be defective Labour costs may apply Where the Unit has been installed by an authorised installer Chamberlain will furnish replacement parts free of charge through the authorised installer A service fee for on site service may apply In warranty service During the warranty period if the product appears as though it may be defective call our toll free service before removal of the Unit A Chamberlain technician will diagnose the problem and promptly supply you with the parts for do it
32. the orange learn button on opener The learn indicator light will glow steadily for 30 seconds 2 Within 30 seconds slide the cover of the C379 up as illustrated A Swipe your finger on the reader head at a steady speed B until the yellow LED turns on C 3 When the opener light flashes it has learned the code If the light bulb is not installed one click will Test reader by pressing be heard ensure there are no obstructions in the K the send button D path of the door then press the send button D to 2 test the door Courtesy light will flash once INSTALL DOOR CONTROL OPTIONAL Multi function wall control fo m 0 Installation There are 2 terminals 1 on the back of the door control Strip about 6mm Separate wires enough to connect the white red wire to RED terminal screw 1 screw 2 Fasten the door control to an inside garage wall with sheet metal screws 3 provided Drill 4mm 5 32 holes and uaa 6 if installing onto plasterboard wall A convenient place is beside the service door and out of reach of children Run the bell wire up the wall and across the ceiling and connect to the garage door opener quick connect terminals which are located behind the light lens of the opener Connect the bell wire to the terminals as follows white red to ti 1 and ens to white 2 Use a screwdriver or pen to press open the spring terminals then insert the cable into the
33. tional Protector System uses an invisible beam which when broken by an obstruction causes a closing door to open and prevents an open door from closing It is STRONGLY RECOMMENDED for homeowners with young children Allow a 15 minute cooling period after 5 continuous operations of the opener The opener light will turn on 1 when opener is initially plugged in 2 when the power is briefly interrupted 3 when the opener is activated The light turns off automatically after 2 1 2 minutes Bulb size is 24V 21W maximum MAINTENANCE OF YOUR OPENER Once a Year Apply grease to rail and trolley Oil door rollers bearings and hinges e DO NOT lubricate the opener itself DO NOT APPLY grease to the door tracks CARE OF YOUR OPENER When properly installed your opener will operate with minimal maintenance The opener does not require additional lubrication Limit and force settings These settings must be checked and properly set when opener is installed Weather conditions may cause some minor changes in the door operation requiring some re adjustments particularly during the first year of operation Refer to setting the limits and force on page 9 Follow the instructions carefully and repeat the safety reverse test after any adjustment Remote control The remote control may be secured to a car sun visor with the clip provided Additional remotes can be purchased at any time for use in all vehicles using garage Refer to a
Download Pdf Manuals
Related Search