Operating Instructions and Parts Manual (automatic) )
Contents
1. Note that colours of live and neutral wires depend on voltage of supply service 5 Replace cover Do not over tighten screws Recommended Mounting Heights from bottom edge of dryer above finished floor AFF Men s 43 109cm Ladies 41 104cm Children ages 11 17 39 99cm Children ages 3 10 33 84cm Disabled oo 89cm Cleaning and Maintenance Periodic cleaning of the unit is recommended to ensure optimum performance e Disconnect the electrical supply e Remove the two cover mounting screws e Remove the cover e Clean all dust lint from the interior of the dryer e Wipe the cover with a soap cloth and mild cleaning solution Do not soak Never use abrasives to clean the cover e Replace the cover Do not over tighten the screws e No touch Operation e Shake excess water from hands e Place hands under the dryer e Rub hands whilst drying Operating Instructions and Parts Manual High speed Hand Dryer nei e Stops automatically after hands are removed 18 20 21 22 Repair parts list Key Description 1 Cover 2 Blower housing 3 Rubber Operating Instructions and Parts Manual Biodrier Eco High speed Hand Dryer 4 Shock absorber 5 Motor rubber 6 Motor 7 Blower housing 8 Blower housing 9 Screw 10 Terminal block 11 Cable clamp 12 Screw 13 Nylon hole bushing 14 Base plate 15 Circuit board module 16 Circuit board cover 17 Heater element 18 Baffle 19 Air outlet 20 Sensor brac2. com High speed Hand Dryer Operating Instructions and Parts Manual automatic Surface Mount 300mm Technical Specifications Item Category Performance Data Operating Voltage 220 240 V 50Hz Air Speed 90m s 200m h Motor Type 650W Adjustable Brush Type Heater Element 250W Thermal Protected Rated Power 900 Watts Drying Time Less Than 10 seconds Circuit Operation Infrared automatic Self Adjusting Timing Protection 60 Seconds Auto Shut Off Drip Proof IPX1 Isolation Class 1 Net Weight 4 5kg Unit Size 300 x 280 x 175 mm Finish White silver Die Cast Aluminium Decibel Rating 0dba 1 mtr Approvals CE GS WEE Cover Type Cover Finish BB70W Die cast aluminium Epoxy polyester powder coating White BB 7OS_ Die cast aluminium Epoxy polyester powder coating metallic Silver Operating Instructions and Parts Manual com High speed Hand Dryer General Safety Information MWe This product is intended for Mane Disconnect power at the service installation by a qualified service person breaker before installing or servicing Use AWG No 16 solid conductor for wiring NOT FOR HOUSEHOLD USE MAY CAUSE BURNS IMPROPRE A L USAGE DOMESTIQUE PUET OCCASIONNER MWe Failure to properly ground unit Maine All units must be supplied with a 3 Could result in severe electrical shock wire service The ground wire must be And or death connected to the dryer s backplate Note Do not install dryer over was
3. hbasin Type Y attachment If the power supply cord is damaged it must be replaced by the manufacturer or Its service agent or a similar qualified person in order to avoid a hazard Means for disconnection must be Incorporated in the fixed wiring in accordance with the wiring rules Lo sl C digital temperature circuit P gai infrared sensor J ELECTRICAL DIAGRAM Installation 1 Make sure power supply breaker is switched off Installation must be carried out in accordance with the current edition of local wiring regulations code having jurisdiction Installation should be performed only by a qualified electrician 2 Place template against wall at desired height see mounting height recommendations and mark locations of 4 mounting holes and wire service entry at knockout KO location Note for two or more dryers dryers should be no closer than 24 inches 610 mm on centre 3 Remove and retain 2 cover screws and cover Connect supply wires to terminal block where indicated and connect ground wire to base plate with ground screw Connections A Connect the live wire coloured red and black to the terminal black marked L B Connect the neutral wire coloured white or blue to the terminal black marked N Operating Instructions and Parts Manual l com High speed Hand Dryer C Connect the ground wire coloured green or green and yellow to the green screw marked D
4. ket 21 Sensor module 22 Sensor screen Operating Instructions and Parts Manual
Download Pdf Manuals
Related Search