USER MANUAL - Dental Concepts
Contents
1. 2 3 full or full for heater models BASIC SETTINGS 4 Simply press Start or Degas keys to commence these cycles To cancel cycles press Stop key 5 To change the timing cycle press More or Less keys to increase or decrease cycle time Factory default is 15 minutes for clean and 5 minutes for degas 6 Once cycle times are optimized simply press Start or Degas and display shows the selected optimized time cycles during countdown DEGAS 7 Adda specified amount of recommended detergent to the ultrasonic tank For the best results first start the machine and then sprinkle the detergent along the insides of the tank 8 Press Degas to expel air bubbles from the water This takes 1 5 minutes depending on water quality Degassing is complete when cavitation surface ripples become evident 9 Adjust time using More or Less keys if necessary or press Start 10 Adjust down Power Level if required Default is 100 maximum power These optimized basic settings will be retained so long as the unit is powered on Issue date 20110506 Page 4 12 11 Leave unit to complete the operation or press Stop to cancel 12 Operate with the lid on where possible 13 After cleaning rinse parts using clean running water FOR HEATER MODELS 14 Follow steps 1 6 before switching on heater 15 Press Heater On to change heater temperature using More or Less keys to increase or decrease temperatures Factory default is 50 C Place lid on the unit to preven2. eg software version 20 Press Status key repeatedly to scroll through various settings on the unit The Status key displays information such as tank temperature clean time degas time power level and software version 21 The Setup keys have other functionalities At present these enable disable buzzer and lids 22 Ultrasonics over prolonged operation will increase above preset temperature Power duty cycle helps maintain preset temperature over prolonged ultrasonic operation Use Setup to scroll to power duty cycle P dc Factory default power duty cycle is off Press More key to turn on showing dc On or press Less key to d OFF to restore to factory default 23 To save optimized settings when the unit is powered press Setup and scroll through display showing U SEt Press More or Less keys to U On confirm saved user setting 24 User setting can be changed by repeating steps 4 6 and automatically saved so long as the unit is powered on 25 To return to factory setting simply press Setup and scroll through display showing F SEt Press More or Less keys to F On to confirm factory setting REFERENCE TABLE The table below is a quick reference to display key functions and error messages We encourage users to familiarize with the advanced functionalities of keys in blue text left of display Start Stop Power On for ultrasonic cleaning End of cleaning cycle Cleaning time in MM SS where MM in minutes and SS in second
3. ie sudden temperature changes add hot water to a cold tank or cold water to a hot tank use external or immersion heater or pour excessively hot or cold liquid into the tank This will damage your unit Note the temperature will rise slightly when the ultrasonics is switched on operate without adequate liquid allow cleaning solutions to become excessively contaminated use dangerous liquids Soniclean Pty Ltd does not accept responsibility for accidents arising from the use of toxic flammable corrosive liquids Issue date 20110506 Page 3 12 operate in normal room temperatures around 25C use adequately and correctly earthed mains electricity supply with correct voltage to your ultrasonic cleaner Check with qualified electrician if in doubt fill at least 2 3 full or full on heated models use a basket tray rack to prevent contact between objects and the tank ensure all splash marks and spillages are cleaned off the unit immediately OPERATING YOUR UNIT CONTROL PANEL SO EASY SO FAST SO CLEAN SONIC LEA N 445 ete E Clear Setup Status as wr y A Se Ny Heater Power Start On Off Level Less More Degas Stop PREPARATION 1 Set the unit on level surface to enable liquid to drain out completely 2 Check for the correct voltage See back label on the unit Plug in your ultrasonic cleaner and switch on at the power point 3 Close the drain valve and fill the tank with cold room temperature or tepid water to
4. 10506 Page 10 12 MANUFACTURER WARRANTY RECORDS WARRANTY Manufacturer Records Return to Manufacturer Our Soniclean Ultrasonic Cleaner is guaranteed for 24 months from the date of purchase Extended 36 months warranty is provided if the user completes and returns within 30 days of purchase the questionnaire downloaded from http www soniclean com au support html We undertake to repair or exchange FREE OF CHARGE any part found to be damaged due to a manufacturing fault This warranty is not transferable and does not cover damage caused by misuse neglect failure to observe operating instruction failure to keep the unit clean accident use of incorrect power supply or attempts to repair by unauthorised personnel The ultrasonic bath tank is not covered against chemical and or cavitation ultrasonic erosion Damage to the transducer caused by excess thermal shock or by other mechanical stresses or attempts to switch on the unit without water liquid is also not covered by this warranty The purchaser agrees to undertake the cost and responsibility of packing and dispatch for safe and timely transportation of the unit to the manufacturer via the premises of the distributor or authorised sales agent IMPORTANT Please retain purchase invoice or receipt for verification if required by the manufacturer Purchased from Date of Purchase Model Serial No Issue date 20110506 Page 11 12 CONTACT INFORMATION S
5. ONICLEAN PTY LTD ACN 057 730 917 ABN 89 057 730 917 38 Anderson Street Thebarton South Australia AUSTRALIA PO Box 398 Stepney 5069 South Australia Australia Phone 61 8 8234 8398 Fax 61 8 8234 8391 Web www soniclean com au Email sales soniclean com au Your local Distributor contact information Place company stamp below go EUROPEAN AUTHORISED REPRESENTATIVE Priory Analysts Ltd The Atrium Park Street Luton LU1 3BE UNITED KINGDOM SO EASY SO FAST SO CLEAN SONICLEAN Issue date 20110506 Page 12 12
6. SO EASY SO FAST SO CLEAN GAN SONICLEAN Z Adaptive Pulse Swept Power USER MANUAL FOR SONICLEAN DIGITAL BENCHTOP ULTRASONIC CLEANERS MODELS 80TD 120TD 160TD HD 250TD HD 500TD HD 800TD HD 1000TD HD 2000TD HD 3000TD HD amp 3800TD HD For further information and updates visit http www soniclean com au support html Issue date 20110506 Page 1 12 CONTENTS PRECAUTIONS SAFETY INSTRUCTIONS CONTROL PANEL OPERATING YOUR UNIT PREPARATION BASIC SETTINGS DEGAS FOR HEATER MODEL ULTRASONIC PERFORMANCE ADVANCED SETTINGS REFERENCE TABLE TROUBLE SHOOTING CUSTOMER WARRANTY RECORDS MANUFACTURER SUPPLIER WARRANTY RECORDS CONTACT INFORMATION Issue date 20110506 Page 2 12 PRECAUTION SAFETY INSTRUCTIONS PRECAUTIONS Membrane keypad The touch sensitive keypad is waterproof with easy wipe down surface Do not operate keys with sharp objects If water enters under the fascia send the unit to an authorized Soniclean service center for repair Aerosols Do not switch on ultrasonic without the lid to prevent possible dangerous aerosols from the liquid Keep lid and tank edge dry to reduce aerosol Models with interlock lid must be enabled to prevent unit operating without the lid Ultrasound pressure It is recommended to cover the tank during the operation Do not position ears directly over bath Noise from ultrasonic is rated around or below 85dBA At high power the unit can
7. factory setting During Setup or Status key presses use Clear to exit routines More Less Set Heater On from 0 C to 60 C First key press displays set temperature Set temperature with More and Less key Set Cleaning from 1 to 99 minutes Press Start to clean with countdown timer More or Less key changes timer to a new value The next Start will continue with the new set time Version S d 08 1 60 Set Degas 1 99 minutes More or Less key changes degas time The next Degas will continue with the new set time Version S d 08 1 60 Power Level Setup More or Less key toggles Enable or OFF states as displayed Preset Degas and Cleaning time using More or Less key Status More or Less key is used in most functions Also see Status key description Clear Not applicable Degas Not applicable Single press of More and Less key will increase or decrease number by 1 in most operations In the clean time holding longer duration changes XX ct values by 10 Issue date 20110506 Page 8 12 TROUBLE SHOOTING GUIDE Foil test Poor Check power level set should be set to High ove 3 Does the unit have recommended amount of detergent Is the detergent approved by SONICLEAN Has the unit degassed properly Whilst in the degas mode look for suspended bubbles in water There should not be any Is the water too hot If so remove some not all and replace with co
8. generate very high frequency pitch which is harmful to sensitive ears Power supply Check that your mains supply is adequately earthed before plugging in to ensure that the voltage is correctly rated Do not attempt to open the unit powered to mains which can cause an electric shock Opening the unit will void the Warranty unless authorised by Soniclean Unit is sealed to International Protection Standard 1P66 67 Insulation tests Insulation resistance tests can not be performed at 500Vdc due to an internal 275Vdc surge arrestor Tests should be limited to 250Vdc Please refer to AS NZS 3551 2004 Technical management programs for medical devices section 5 3 4 Insulation resistance test specifications SAFETY INSTRUCTIONS The ultrasonic vibrations of these cleaners are transferred to the water by means of a ceramic transducer which is bonded to the underside of the tank These transducers are brittle and can easily be damaged through incorrect use However with proper care they can give many years of reliable service Following these directions will prolong the life of your unit and increase the effectiveness of the cleaner DO NOT subject unit to mechanical or thermal shocks immerse your unit drop or place heavy or sharp objects directly in tank place objects into tank while ultrasonic cleaning is in progress overload tank as this can damage parts and is less efficient in cleaning subject tank to thermal shock
9. ld water Replenish the detergent to bring to the correct concentration Is the aluminum foil too thick should be 0 025mm thickness Is the water too dirty If so replace with fresh water Note water quality can vary from day to day and from place to place Degas again 7 Remove trays and instruments part during foil test Note Good foil test Very fine indentations and holes at shorter test duration Longer foil test causes perforations If the unit stops 1 Allow unit to cool down unplugging switch off at wall while 2 If bath water is hot empty out bath operating 3 Wait for at least half an hour before switching on the unit Cause could be again thermal cutout 4 If unit still does not work contact your supplier or SONICLEAN NOISE 1 If unit makes a screeching noise switch Off and try letting screeching unit sit for a few minutes to degas again Error messages Water over temperature when unit is above max 70 C and the unit will cut out allow unit to cool down and press Start to continue Ultrasonic power overload or over current or electronics over temperature allow unit to cool down and press Start to continue When Lid is enabled and lid is open When the lid interlock is enabled and the lid is opened the ultrasonics will pause When lid is replaced press Start to continue Moisture detected inside the unit from by leakage or condensation the unit will cut out This error me
10. s The cleaning time is preceded by degassing cycle Water temperature updated every 5 sec XX 100 Power levels Degas Degas displays every 5 sec Cleaning time The display is in MM SS where MM in minutes and SS in seconds Degas cycle is H 3 M 1 L 1 OFF1 SEC Power Level 100 P Press repeatedly to scroll through and select Power levels when 80 P unit is in standby or operating Issue date 20110506 Page 6 12 Heater On Off Heater On Key valid when heater is enabled The LED will blink when the set temperature is reached With out ultrasonics the H On display will flash after one minute to indicate that the heater is on Heater OFF Key valid when Heater is disabled Use More or Less to set temperature Max 60 C XX C LED lights up when heater is active Status XX C Water temperature updated every 5 seconds XX C Heater temperature set Dot before C indicates heater set temperature MM SS Cleaning time The display format is MM SS where MM is minutes and SS is seconds Total cleaning time includes degassing time 100 P 80 P 60 P Power level set Display 100 P 80 P 60 P XX ct Cleaning set time where XX is from 1 to 99 minutes XX dG Degas time set where XX is from 1 to 99 minutes XX dc Duty cycle factory default set is 50 showing 50 dc Use More or Less key to change the values When activated in Se
11. ssage may be reset with any key press Issue date 20110506 Page 9 12 CUSTOMER WARRANTY RECORDS WARRANTY Customer Records Our Soniclean Ultrasonic Cleaner is guaranteed for 24 months from the date of purchase Extended 36 months warranty is provided if the user completes and returns within 30 days of purchase the questionnaire downloaded from http www soniclean com au support html We undertake to repair or exchange FREE OF CHARGE any part found to be damaged due to a manufacturing fault This warranty is not transferable and does not cover damage caused by misuse neglect failure to observe operating instruction failure to keep the unit clean accident use of incorrect power supply or attempts to repair by unauthorised personnel The ultrasonic bath tank is not covered against chemical and or cavitation ultrasonic erosion Damage to the transducer caused by excess thermal shock or by other mechanical stresses or attempts to switch on the unit without water liquid is also not covered by this warranty The purchaser agrees to undertake the cost and responsibility of packing and dispatch for safe and timely transportation of the unit to the manufacturer via the premises of the distributor or authorised sales agent IMPORTANT Please retain purchase invoice or receipt for verification if required by the manufacturer Purchased from Date of Purchase Model Serial No Notes Issue date 201
12. t heat loss and evaporation Press Heater Off to switch off the heater 16 The LED display blinks when the liquid reaches the set temperature 17 Ensure that minimum liquid level is maintained to prevent heater shut down 18 Ifthe heater shuts down top up liquid press Heater On again ULTRASONIC PERFORMANCE To ensure your unit is working effectively a daily aluminum foil test is recommended Soniclean recommends 0 025mm thick aluminum foil Thicker foil will not work For consistent results use SONIC 1 ARTG No 141350 detergent dilution 0 5 3 0 and fluid temperatures from 22 C 60 C Sonic 1 detergent has been specially formulated by Soniclean to give the best results for Soniclean machines Be aware that certain chemicals or excessive amounts of certain chemicals affect the performance or damage unit Check with your supplier if in doubt Refer to Sonic1 performance graphs www soniclean com au support html Soniclean now provides an Ultrasonic Performance Meter UPM Model Sonic 200 250 which validates or takes the place of the foil test Refer to Australian Standard AS2773 Check Soniclean Web Site www soniclean com au for further information for UPM and Foil Test Soniclean s Ultrasonic Performance Meter Soniclean s detergents Issue date 20110506 Page 5 12 ADVANCED SETTINGS 19 Check to ensure the features and functionalities correspond to software version number Press Status key and scroll through to display
13. tup this functionality will be activated when the bath temperature is close to the set temperature Software Version Setup Enable or disable audible key press Press Less key to silent operation using b OFF Press More key b On Load factory values The display shows F SEt Press More or Less key to toggle F On The factory values are Ultrasonic power 100 Clean Time 15 0 minutes Degas Time 5 0 minutes Heater Temperature 50 C Duty cycle disabled Lid disabled Beep enabled U SEt U On User setup Use More or Less key to toggle U On Lid L On L OFF Lid o PAUS Lid interlock option Use More to enable lid interlock Use Less to disable lid interlock When lid interlock is enabled and the lid is open When the lid interlock is enabled and the lid is opened the ultrasonics will pause When lid is replaced press Start to continue P dc Power set to enable or disable Duty cycle Default value is 50 of 5 Issue date 20110506 Page 7 12 sec period See status key for the Duty cycle set Enable Duty Cycle with More key factory default 50 power Disable Duty cycle with Less key and ultrasonic is set to continuous 100 duty set operation Clear Press Clear to Switch off heater Remove error message without starting up ultrasonics Restore user setting Reset factory setting Press Status key and scroll through to check status on user or
Download Pdf Manuals
Related Search