Home

WIRELESS BLOCKAGE MONITOR INSTALLATION MANUAL

1. GND RESET ki Figure 5 Access Point LAN connection a NOTE The access point will only receive power when it is plugged into the cigarette lighter and the cigarette lighter is providing power This may require the tractor key to be in the on position 4 Replace the access point s back cover by sliding the cover on and pushing the tab down The power cable should rest in the notches in the access point and cover 5 Remove the paper backing from the oil resistant cork rubber gaskets 351521 000004 and place the adhesive side onto the curved feet of the access point assembly called out in Figure 6 Page 19 of 55 Revision 1 1 Ka Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 Secure the access point to the tractor cab s mounting bar or another rigid surface in the cab using the cable ties included with the packaging of the access point assembly or with the 7 9 cable ties 355032 000004 included in the Master ECU kit NOTE Steps 7 through 9 are optional steps that describe how to install the wire guides Wire guides may be used to help secure the access point power cable to the tractor cab such as to the dash Installing the wire guides for the access point power cable reduces the chance of the cable becoming tangled or becoming caught by e g the operator s hands Clean the area where you will be placing the wire guides 355005 000004 with the alcohol wipes 35906
2. Section 2 4 o NOTE Access point must be powered e iPad connected to Wireless Blockage Monitor WLAN Section 2 4 e Determine if there is an existing work switch and if so where it is located The Wireless Blockage Monitor work switch should be installed as close to the existing work switch as possible if one exists e Determine what method is used by the air seeder s existing work switch see About work switch methods on previous page The method considered default by IAS is when the work switch and magnet are close when the air seeder is in the ground Other related procedures e Installing the Master ECU harness see Section 2 6 o The work switch will be connected to the Master ECU after installation is completed e Configuring the work switch see Section 2 11 o After installation the work switch must be configured using the Wireless Blockage Monitor app Installation Location The Wireless Blockage Monitor work switch should be installed as close as possible to the air seeder s existing work switch if one exists The existing work switch is typically found towards the center of the air seeder s frame on a hydraulic cylinder If there is not an existing work switch on the air seeder refer to the To install a work switch on an air seeder if not existing work switch is present instructions to help determine where the Wireless Blockage Monitor work switch should be installed Page 22 of 55 al Wireless Blockage
3. 4 onto an ECU with the serial number 0000 00001 and that run is connected to the port labeled 4 on that ECU select 0000 00001 Port 4 from the drop down menu 5 Press Save when you have finished adding the ECU and its flow sensors 2 34 PM Edit Current Configuration Select a Manifold to Edit Work Switch Reversed Master ECU Figure 20 Edit Current Configuration screen Page 41 of 55 Revision 1 1 Ko Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 To manually add a flow sensor 1 Press the Configure icon on the Wireless Blockage Monitor app s home screen 2 Press Configure on the Configuration Summary screen 3 Press the name of that that run s flow sensor hose is connected to on the Edit Current Configuration screen 4 From the Edit a Manifold screen shown in Figure 21 use the drop down menu to select which ECU port the respective run s sensor flow hose is connected to Refer to Figure 17 to determine how the runs are numbered a EXAMPLE If you are adding Run 4 onto an ECU with the serial number 0000 00001 and that run is connected to the port labeled 4 on that ECU select 0000 00001 Port 4 from the drop down menu 5 Press Save when you have finished making changes IMPORTANT If the flow sensors or ECUs that were manually entered into the Wireless Blockage Monitor app continuously appear to be blocked on the Wireless Blockage Monitor app the equipment may have been in
4. December 13 2011 To manually configure the Wireless Blockage Monitor If the Wireless Blockage Monitor app was not able to detect all of the flow sensors or ECU or it detected too many ECUs or flow sensors you may manually enter or delete them in the Wireless Blockage Monitor app To manually add an ECU 1 Press the Configure icon on the Wireless Blockage Monitor app s home screen 2 Press Configure on the Configuration Summary screen 3 Press the button located on the upper right corner of the gray box in the middle of the Edit Current Configuration screen shown in Figure 20 4 Perform the following steps while on the Edit a Manifold screen a Rename the Manifold optional Press the Manifold Name field An on screen keyboard will appear Using the on screen keyboard type the desired manifold name For guidance on this topic refer to Section 2 12 b Enter the ECU s serial number Press the Serial Name field An on screen keyboard will appear Using the on screen keyboard type the ECU s serial number The ECU s serial number is listed on a sticker on the ECU i NOTE To access the numeral keys press hel 21237 button on the on screen keyboard c Add flow sensors to the manifold Using the drop down menu select which ECU port the respective run s sensor flow hose is connected to Refer to Figure 17 to determine how the runs are numbered i Repeat this step for each run contained on that manifold ii EXAMPLE If you are adding Run
5. a free software application that may be downloaded onto your iPad from Apple s iTunes App Store The Wireless Blockage Monitor app communicates any run blockages to the operator and allows the operator to configure the system Part Name Part Number Z Contained within 153025 000024 May not be included iPad if included with the with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 9 Parts needed to download Wireless Blockage Monitor app About the inclusion of the iPad with the Wireless Blockage Monitor system There are two methods that customers obtain the iPad that they will use with the Wireless Blockage Monitor purchased from IAS as part of the Wireless Blockage Monitor system or purchased elsewhere iPads that are included in with the Wireless Blockage Monitor will come preconfigured that is installed with the Wireless Blockage Monitor app and signed into a default Apple ID For more information about Apple IDs reference Creating an Apple ID If you wish to download additional apps onto a preconfigured iPad reference To download additional free apps on a preconfigured iPad and To download non free apps on a preconfigured iPad Tools needed to download Wireless Blockage Monitor app None Number of times procedure is performed If required each step will only need to be performed once Steps that must be completed prior to this procedure For iPads not included wi
6. and by displaying the blocked runs or manifolds on the Blockage screen NOTE The flow sensors have been designed to be attached to a 1 25 diameter final run hose If your air seeder has 1 diameter run hoses follow the To install flow sensors on 1 diameter final run hoses instructions Part Name Part Number Peete Contained within 1 25 Hose Clamp 352013 000005 2 run Standard sensor kit Adaptor Hose 351060 000008 1 run Standard sensor kit Sensor 153570 000015 1 run Standard sensor kit Table 15 Parts needed to install flow sensors on standard 1 25 diameter final runs Tools needed 5 16 socket 5 16 nut driver on a cordless drill or a flathead screwdriver Number of times procedure performed Once per run Steps that must be completed prior to the procedure None Other related procedures e Installing the ECU Section 2 7 e Connecting flow sensors to the ECU Section 2 9 e Configuring the Wireless Blockage Monitor Section 2 10 Page 33 of 55 Revision 1 1 Ka Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 Installation location Flow sensors are to be installed at beginning of every run of the air seeder next to the manifold To install the flow sensor on standard 1 25 diameter final run hoses 1 Attach the adapter hose 351060 000008 to the sensor assembly 153570 000015 2 Slide a 1 25 hose clamp 352013 000005 o
7. be completed prior and other related procedures The appendix of this document includes information that while not vital to the installation process allows for a deeper understanding about that specific topic 1 2 Wireless Blockage Monitor parts list The following components are required for installation of the Wireless Blockage Monitor The number of each component that is needed for installation will vary based on your air seeder configuration as noted in the Quantity Needed column Kit Name Standard Sensor Kit See Table 2 or 153025 000015 Nonstandard Sensor Kit See Table 3 Part Number Quantity Needed 1 per final run Page 7 of 55 Ubolts with Saddle Clamp Options for ECU mounting bracket Diameter of manifold tower determines size of U bolt needed 2 diameter U bolt 352013 000006 2 5 diameter U bolt 352013 000007 3 diameter U bolt 352013 000008 4 diameter U bolt 352013 000009 2 per manifold Tractor Kit See Table 4 153025 000016 1 per system Master ECU Kit See Table 5 153025 000019 1 per system ECU Kit See Table 6 153025 000017 1 per manifold minus 1 due to ECU master kit Table 1 Kit list for installation cont d on next page e Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Air seeders with 4 or more manifolds Intermediary Harness 3 less tha
8. that the implement is out of the ground 3 Press the Blockage icon on the Wireless Blockage Monitor app s home screen 4 Note the color of the circle next to the Work Switch on the top left corner of the Blockage screen henceforth referred to as the Work Switch circle The Work Switch circle should be green at this time 5 Adjust the air seeder s hydraulic system so the implement is in the ground Note the color of the Work Switch circle It should have changed to gray 6 Adjust the air seeder s hydraulic system so that the implement is out of the ground again The Work Switch circle should have changed to green a If the Work Switch circle is not the correct color or does not change when you adjust the air seeder s hydraulic system contact IAS for assistance Page 45 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Vi 2 12Renaming the ECUs in the Wireless Blockage Monitor app About renaming the ECUs in the Wireless Blockage Monitor app This optional procedure will label the ECUs in the Wireless Blockage Monitor app in a manner that will allow them to be more easily identified especially when troubleshooting a run or total manifold blockage By default the ECU will be labeled with its twelve digit serial number in the Wireless Blockage Monitor app NOTE ECUs are listed in alphabetical numeric order on the Blockage screen in the Wireless Blockage M
9. 0 000003 Remove and discard the paper backing from the wire guides Place the adhesive side of the wire guides onto the desired location on the tractor cab next to the access point power cable Place the access point power cable into the hook of the wire guide L 2989 pink e c Figure 6 Apply the gasket to the feet of the access point To connect the iPad to the access point network 1 DP tabu Power on the tractor power on the iPad and connect the access point power cable to the tractor s cigarette lighter if you have not done so already Press the Settings icon on the iPad s home page Press the Wi Fi icon on the top left corner of the screen Ensure that Wi Fi capabilities are on the gray bar to the right of Wi Fi will display ON Press I ASBlockage under Choose a Network list a NOTE If ASBlockage does not appear on the Choose a Network list wait a few minutes to give the iPad time to search for the network If after several minutes the network does not appear contact IAS for assistance A checkmark will appear to the left of the ASBlockage network and the network name will turn blue on the Choose a Network list when the iPad is connected to the network Page 20 of 55 Al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 5 Installing the work switch About the work switch The work switch serves as a signal to the Wireless Blockage Moni
10. 004 000003 Rail attachment for tablet iPad mount 352004 000004 k Wire Guide 355005 000004 6 Alcohol Wipes 359060 000003 2 Three Way Cigarette 2 Lighter Adaptor 154005 000004 1 Oil resistant cork rubber gasket included with the SEH S Access Point Table 4 Tractor Kit Subcomponents Quantity Part Name Part Number included per Kit Wireless Blockage Monitor Module Neots oun i ECU Mounting Bracket 351050 000012 1 ECU Bracket Shield 351050 000015 2 1 4 20 Steel Locknut 352011 000040 8 Miniature Cable Tie 355032 000003 25 Workswitch Bracket 351050 000016 1 Cotter Pin 3 32 diameter 352015 000011 4 Workswitch 153560 000014 1 Cable Tie 7 9 355032 000004 100 Ceramic Workswitch Magnet 359035 000001 1 V4 Steel Washer 352012 000024 10 Va 20x12 Steel Bolt 352010 000084 2 3 Way DTM Splitter 355030 000002 2 27 foot Intermediary Lenawee 355020 000019 1 22 foot ECU Harness Worle Switch 355020 000018 1 Table 5 Master ECU Kit subcomponents Revision 1 1 Ko Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 Quantity Part Name Part Number included per Kit Wireless Blockage Monitor Module EH Gel 351050 000012 1 Bracket ECU Bracket Shield 351050 000015 2 1 4 20 Steel Locknut 352011 000040 6 Miniature Cable T
11. 019 into the three way splitter at the end of the tractor harness 2 Insert a Deutsch sealing plug assembly 153060 000015 into the remaining receptacle of the three way splitter to prevent foreign material from entering the three way splitter 3 Extend the intermediary harness around the side of the air cart and to the air seeder s hitch If the intermediary harness does not need to be fully extended to reach the air seeder s hitch coil the extra length of the harness around a hydraulic line or electrical wire 4 Using 7 9 cable ties 355032 00004 secure the intermediary harness to the air cart To connect an intermediary harness to an intermediary harness NOTE This step does not have to be performed for air seeders with less than five manifolds NOTE Up to two intermediary harnesses may be connected to the end of another intermediary harness 1 Connect the black end of the intermediary harness 355020 000019 into the three way splitter at the end of the already installed intermediary harness a NOTE If only one wiring harness intermediary ECU or Master ECU will be connected to the three way splitter of the intermediary harness insert a Deutsch sealing plug assembly 153060 000015 into the remaining receptacle of the three way splitter to prevent foreign material from entering the three way splitter Refer to the appropriate figures in Appendix A to determine if two wiring harnesses will be connected to the intermediary harness s
12. 16 Parts needed to configure the Wireless Blockage Monitor system 39 Table 17 Parts needed to configure the work switch AEN 44 Table 18 Parts needed to rename the ECUs in the Wireless Blockage Monitor app 46 Record of Revision degen Change Description Revision Date Inserted By 1 0 Initial release 10 27 2011 CJW Modified Downloading the Wireless Blockage Monitor app section Added About the inclusion 1 1 of the iPad with the Wireless Blockage Monitor 12 13 2011 CJW system and To sign out of a default app store account instructions within that section Related Documentation Document Number Document Title 600890 000015 Wireless Blockage Monitoring Operator s Guide Page 5 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Glossary Abbreviation Term Definition Access Point In the Wireless Blockage Monitor the access point is the equipment that broadcasts the local wireless network s signal A Software A computer program especially one designed for a mobile PP application device A mechanism built in to the Wireless Blockage Monitor that BIT Built in Test allows that equipment to test itself for and alert the operator of any possible problems Eldon A component of the Wireless Blockage Monitor that allows ECU Control Unit for the communication of the flow sensors to the iPad software
13. 8 manifold wiring harness sisiccivcasssacesorscatecareedsceentcsteeertearnearccetteereeareeariictxeere 52 Figure 32 Nine 9 manifold wiring harness eee ennen 53 Figure 33 Ten 10 manifold wiring harness eee ennen nerne 54 Figure 34 Wiring Harness Diagram with Seed Cart 55 Page 4 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Table of Tables Table Kit list for install AMON craks stearic eiceceeras tear eicareeraitiotsneimeuiaabtievessinareiaitiswusicivnasrdievexsinusec 8 Table 2 Sensor Kit Subcomponents uk 8 Table 3 Tractor Kit Subcomponents 22s foe cs ctsedessncnactcaskeddccctuieccctanddvaentuadiccatadsesossueescticedevanmacdes 9 Table 4 Master ECU Kit subcomponents AAA 9 Table 5 ECU Kit Subcomponents a Se es eid cad Sede 10 Table 6 Intermediary Harness Kit Subcomponents un 10 Table 7 Access Point Window Mounting Kit optional 10 Table 8 Parts needed to download Wireless Blockage Monitor app 13 Table 9 Parts needed to install the iPad mounting bracket nr rrreren nn nen 16 Table 10 Parts needed to install ACCESS point 18 Table 11 Parts needed to install Work ewitch 22 Table 12 Parts needed for installing the wiring bammesses AAA 26 Table 13 Parts needed to install the BCU ie icciccssiavtcuntcesacs selec ennen 30 Table 14 Parts needed to install flow sensors 2 33 Table 15 Parts needed to connect flow sensors to the EC 36 Table
14. Attach an additional 1 25 hose piece onto the bottom of the sensor assembly 1530570 000015 While the length of this piece may vary a 3 inch piece would suffice 7 Slide the additional 1 25 hose clamp onto the 1 25 hose piece 8 Place the final run hose into the 1 25 hose piece Tighten the hose clamp using a 5 16 socket a 5 16 nut driver on a cordless drill or a flathead screwdriver Page 35 of 55 el Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 9 Connecting flow sensors to the ECU and installing ECU shield brackets About connecting flow sensors to the ECU Flow sensors must be connected to the ECU in order for the flow measurements to be communicated to the iPad software app About ECU shield brackets ECU shields help to prevent the flow sensor tubes from becoming disconnected from the ECU ports during operation transportation or storage of the air seeder ECU shield brackets should not be installed until after the flow sensors have been connected to the ECU Quantity d SC Part Name Part Number needed Contained within ECU Bracket Shield 351050 000012 2imanifola Master Er s l ECU Cotter Pin 3 32 352015 000011 lmanitold Master ECU and ECU diameter kits Miniature Cable Tie 355032 000003 1 run Master ECU kit Table 17 Parts needed to connect flow sensors to the ECU Tools Needed e Pliers e Paint pen or othe
15. INTELLIGENT Agricultural Solutions SS LOCK AGE og ON Ns ST ALLATIO N MAN Revision 1 1 FOR TECHNICAL SUPPORT TELEPHONE 701 356 9222 E MAIL support intelligentag com al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Wireless Blockage Monitor Installation Manual 2011 Intelligent Agricultural Solutions All Rights Reserved Wireless Blockage Monitor Installation Manual All content within is copyrighted by Intelligent Agricultural Solutions and may not be reprinted without permission The content of this manual is furnished for information use only is subject to change without notice and should not be construed as a commitment by Intelligent Agricultural Solutions Intelligent Agricultural Solutions assumes no responsibility or liability for any errors or inaccuracies that may appear in the information content contained in this guide Patent pending Intelligent Agricultural Solutions and Wireless Blockage Monitor are trademarks or registered trademarks of Intelligent Agricultural Solutions Intelligent Agricultural Solutions 1810 NDSU Research Circle North Fargo N D 58102 USA Visit us on the web at http www intelligentag com Questions E mail us at info intelligentag com Page 2 of 55 Sal Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 T
16. Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To install a work switch on an air seeder NOTE These instructions are for installing a work switch on an air seeder in which a work switch was already present If your air seeder does not have an existing work switch follow the To install a work switch on an air seeder if no existing work switch is present instructions below 1 Slide one Li steel washer 352012 000024 onto the end of a 20 x 12 steel bolt 352010 000084 Insert the bolt into the work switch bracket 351050 000016 The washer should rest against the bolt head and the work switch bracket 2 Repeat Step 1 with the remaining bolt 3 Install the work switch bracket to the air seeder If possible install onto the existing work switch bracket If this is not possible refer to the To install a work switch on an air seeder if not existing work switch is present instructions 4 To secure the work switch bracket to the existing bracket or air seeder thread in order one steel washer and one Lo 20 steel locknut 352011 000040 onto the ends of each bolt refer to Figure 8 5 Remove the front locknut from the work switch assembly 153560 000014 and insert it into the work switch bracket 6 Place the ceramic work switch magnet 359035 000001 onto the air seeder s frame near the air seeder s existing work switch magnet 7 Replace the locknut onto the work switch assembly refer to F
17. Monitor app to communicate any run blockages to the operator Depending on how your tractor s cigarette lighter operates i e if the cigarette lighter only powers on devices when the tractor is on this may require your tractor key to be in the on position in order for the access point to transmit Figure 4 Wireless Blockage Monitor Access Point Quantity a Part Name Part Number needed Contained within Access Point 150570 000002 1 Tractor kit Access Point Power 355020 000031 1 Tractor kit Wee 154005 000004 1 Tractor kit Wire Guides 355005 000004 Varies Tractor kit Alcohol Wipes 359060 000003 1 Tractor kit Oil resistant ee MET ih 351521 000004 2 Tractor kit Access Point 153025 000024 May not be included iPad if included with the with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 11 Parts needed to install access point NOTE Two cable ties are included in the packaging of the access point assembly If these cable ties become lost or misplaced you may use some of the 7 9 cable ties in the Master ECU kit Tools need to install access point None Page 18 of 55 Sal Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Number of times procedure is performed Once per Wireless Blockage Monitor system Steps that must be completed prior to this procedure e Wireless Blockage Monitor app must be
18. U Work switch 3 amp outlet 3 way splitter Tractor harness Intermediary harness ECU harness Master ECU harness Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Ten Manifold Wiring Harness Diagram AO ei Coa Ba Ba z ae aii p og eg p w N ee T Figure 32 Ten 10 manifold wiring harness Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Wiring Harness Diagram with Seed Cart Tractor Seed Cart Manifold ECU Work switch Figure 33 Wiring Harness Diagram with Seed Cart 3 amp outlet 3 way splitter Tractor harness Intermediary harness ECU harness Master ECU harness Page 55 of 55
19. able of Contents RELATED DOCUMENTATION bicccicicncncsecicececeScssscnatawenecescnnscbeatiecesuacnuyssucswoeeluacavawacceunucueavadenedenmvadewassvewucessns 5 GLOSSARY EE 6 1 INTRODUCTION E 7 1 1 HOW TO USE THIS MANUALE 7 1 2 WIRELESS BLOCKAGE MONITOR PARTSUST kk kk reen kk kernen en kk ener ennen nn renen 7 1 3 TOOLS REQUIRED EEN 11 1 4 TECHNIGCAL ASSISTANGE eebe een Eege EE Ae deeg 11 2 INSTALLATION INSTRUCTIONS iecnccicccdeccceticc geheegt Nee cveenedeceecaxddeuesulsasacevoceanpedense 12 2 1 OVERVIEW CHECKUIST RENE RER E NEL RENEE ELLE EL ENE EEN LEE RE ERR ennen ener n es 12 2 2 DOWNLOADING THE WIRELESS BLOCKAGE MONITOR App 13 2 3 INSTALLING THE IPAD MOUNTING BRACKET 16 2 4 INSTALLING THE ACCESS POINT ocecccccccceeeececcceseeceeeeeeeceeesceuaeeeseceeeeeueuaaeusseseeeeeeeuaeeuseeeeeeeeuaaaeeeseeeeees 18 2 5 INSTALLING THE WORK SWITCH ERE EEE EnaA AEAEE EEEE TERRE REEL TERE RR e en ennen 21 2 6 INSTALLING THE WIRING HARNESSES ssoieieisisseeeeteiniirneest ttr ikin nenten nnne ennan EEEE EnA A EEEE E EEan EEEE EEEn nenene 26 2 7 INSTALLING EQUUS EE 30 2 8 INSTALLING FLOW SENSORS G u ssseeveueeeeeeeeet ett kk bb NERE ERE RER E ERNE RER ERE N ER ERE E RENEE ERE E ER ENERET LEE N Rk r ennen ne 33 2 9 CONNECTING FLOW SENSORS TO THE ECU AND INSTALLING ECU SHIELD BRACKETS 36 2 10 CONFIGURING THE WIRELESS BLOCKAGE MONITOR 0cccccccccsceeeeeeeececeeesceueeesceceeeseuuaeeeeseeeeeeanaeees 39 2 11 CONFIGURING THE WORK SWITCH cccccccc
20. above the air seeder is out of the ground and the hydraulic cylinder is moved apart Page 25 of 55 Revision 1 1 YW Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 2 6 Installing the wiring harnesses About the wiring harnesses The wiring harness provides power from the tractor to the Wireless Blockage Monitor system There are four different wiring harness types 1 tractor 2 intermediary 3 ECU and 4 Master ECU The number of intermediary and ECU harnesses needed for each installation varies based on the number of manifolds on the air seeder as noted in Table 13 Installing a wiring harness on when a seed cart is between the tractor and air seeder If a seed cart is connected between the tractor and the air seeder an extra intermediary harness is needed If using this setup run the intermediary harness that is directly connected to the tractor harness along the side of the seed cart and secure the harness to the hydraulic line of the seed cart Insert a Deutsch sealing plug assembly 153560 000015 into the unused receptacle of the three way splitter to prevent foreign materials from entering the three way splitter From the end of this intermediary harness resume the normal wiring harness setup Part Name Part Number Quantity needed Contained within Tractor harness 355020 0000021 1 Tractor kit For air seeders with two manifolds 1 For air seeders with three 27 foot In
21. app via a WiFi connection A semiconductor diode that converts applied voltage to LED Light Emitting light In the Wireless Blockage Monitor an LED is used to Diode signify if the ECU is receiving power and functioning properly WiFi Wireless A local area network that uses high frequency radio signals Fidelity to transmit and receive data over short distances A component of the air seeder equipment that signifies when the equipment is enabled in the ground or disabled Work Switch out of the ground When the work switch is signals that the air seeder is out of the ground the audio alarm that would normally alert the operator to blockage of flow in the equipments run will automatically be silenced Page 6 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 g 1 Introduction 1 1 How to use this manual This manual will guide you through the entire process of installing the Wireless Blockage Monitor on your air seeder implement e Section 2 includes instructions for installing all of the components of the Wireless Blockage Monitor in the order they are to be installed o Each subsection within Section 2 includes instructions for one procedure of the installation In addition to the actual instructions for the procedure the subsections includes a short introduction about the component being installed the parts and tools needed for that procedure steps that must
22. arnesses may be attached to the tractor harness NOTE If an air cart is attached between the tractor and the air seeder skip to the To connect an intermediary harness to a tractor harness when air cart is in between instructions below 1 Connect the black end of the intermediary harness 355020 000019 into the three way splitter at the end of the tractor harness a NOTE If only one intermediary harness will be connected to the tractor harness insert a Deutsch sealing plug assembly 153060 000015 into the remaining receptacle of the three way splitter to prevent foreign material from entering the three way splitter Refer to the appropriate figures in Appendix A to determine if two intermediary harnesses will be connected to the tractor harness s three way splitter 2 Extend the intermediary harness over the air seeder Use the appropriate figures in Appendix A to help guide the placement of the intermediary harness a NOTE If the intermediary harness does not need to be fully extended to reach where it must connect coil the extra length of the harness around a hydraulic line or electrical wire 3 Using 7 9 cable ties 355032 000004 secure the intermediary harness to the air seeder To connect an intermediary harness to a tractor harness when air cart is in between NOTE This step only needs to be performed if an air cart is attached between the tractor and the air seeder 1 Connect the black end of the intermediary harness 355020 000
23. art Name Part Number eN Contained within 153025 000024 May not be included iPad if included with the with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 19 Parts needed to configure the work switch Tools Needed None Number of times procedure performed Once per Wireless Blockage Monitor system Steps that must be completed prior to this procedure e Download the Wireless Blockage Monitor app on the iPad Section 2 2 Install the access point Section 2 4 Install the work switch Section 2 5 Install the wiring harness Section 2 6 Configure the Wireless Blockage Monitor Section 2 10 o Change which ECU is labeled the Master ECU Section 2 10 e Determine what method the existing work switch on your air seeder uses refer to About work switch methods in Section 2 5 o Follow the respective instructions below based on which method the air seeder uses e For air seeders using the non default method only Reverse the work switch option in the Wireless Blockage Monitor app included in Section 2 6 Other related procedures None Installation location Not applicable See Section 2 6 for information about the work switch s installation location Page 44 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To ensure work switch has been correctly installed default method NOTE The default and non default work switch methods are descr
24. ation of the work switch Section 2 5 Other related procedures e Installation of the ECUs Section 2 7 Installation location IAS recommends installing the wiring harness on top of an existing wiring harness or hydraulic hose on the air seeder when possible or running the intermediary harness through the yoke of the air seeder Doing so reduces the chance of the wiring harness becoming pinched during operation or transportation of the air seeder To connect a tractor harness to a tractor 1 Connect the tractor harness 355020 000021 to the tractor s three pin power outlet This outlet is located in the tractor cab If you are unsure of the location of the three pin power outlet in your cab consult your tractor s owner s manual a NOTE If your tractor does not have a three pin power outlet please contact IAS for assistance 2 Extend the tractor harness until it reaches the hitch of the air seeder a NOTE If the tractor harness does not need to be fully extended to reach the air seeder hitch coil the harness around a hydraulic line or electrical wire 3 Using 7 9 cable ties 355032 000004 secure the tractor harness to the tractor and or air seeder to prevent the wiring harness from becoming snagged on the tractor tires Page 27 of 55 el Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To connect an intermediary harness to a tractor harness NOTE Only two intermediary h
25. cccceeeeceececeseseueeeeueceeesceuaueesuceeeseseuuauesseseeeeeeuaaeueseeeeeeenaaees 44 2 12 RENAMING THE ECUS IN THE WIRELESS BLOCKAGE MONITOR APP 46 APPENDIX A WIRING HARNESS DIAGRAMS PER AIR SEEDER CONFIGURATION MGM seerne 49 TWO AND THREE MANIFOLD WIRING HARNESS DIAGRAMS GGu ssseeeeeeeeeeeeereee eee n entreen ken nere renen erb nerne nn rr n nerne 49 FOUR AND FIVE MANIFOLD HARNESS DIAGpBAMS nna 50 SIX AND SEVEN MANIFOLD HARNESS DIAGpAM ERR RER E LERNER TEE n Renner nr kernen es 51 EIGHT MANIFOLD WIRING HARNESS DIAGpAM esner nt krknna anuna nn nnen e nenn r ennnen nna 52 NINE MANIFOLD WIRING HARNESS DIAGRAM G ussssseeeeeeveeee nett kk tb ERE E RR ERR EL E ENERET E RENNER REE E ERE REEL E REE R REE e rene nen 53 TEN MANIFOLD WIRING HARNESS DIAGpAM teatre ntk n ennnen EEE EEA A AEAEE EEEn EnEn EEEn nenna 54 Page 3 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Table of Figures Figure 1 Installation location E 12 Figure 2 A screenshot from the Wireless Blockage Monitor app 13 Figure 3 An iPad mount attached to a tractor s mounting bar 16 Figure 4 Wireless Blockage Monitor Access Pot 18 Figure 5 Access Point LAN connection ssssseeereer ener 19 Figure 6 Apply the gasket to the feet of the access point EEN 20 Figure 7 Wireless Blockage Monitor work switch assembly u ssseseeereeereererern rr ener nn 21 Figure 8 Installing the work switc
26. ction 2 12 o Operators may changes how a ECU is labeled in the Wireless Blockage Monitor app so that it may be more easily identified when troubleshooting a run or total manifold blockage Installation location An ECU should be installed directly underneath each manifold of the air seeder IAS recommends installing the bracket so that the ECUs will face towards the tractor To install the ECU mounting bracket 1 Remove the nuts and saddle clamp from the ends of the u bolt 852013 00006 352013 000007 352013 000008 or 352013 000009 2 Place the u bolt around the manifold post immediately under the manifold 3 Place a ECU mounting bracket 351050 000012 so that the ends of the u bolt are going through the top two holes of the ECU mounting bracket as shown in the top circle of Figure 13 Replace the saddle clamp and nuts onto the u bolt Remove the nuts and saddle clamp from another u bolt Place another u bolt around the manifold post and through the bottom holes of the ECU mounting bracket as shown in the bottom circle of Figure 13 7 Replace the saddle clamp and nuts onto the second u bolt Dane Uo cooo 0 Tractor lp 0 D ole Blo col E bs mm Figure 13 Mounting a ECU bracket to the air seeder tower Page 31 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To install the ECU 1 Place and hold the ECU ass
27. ctor s mounting bar or other desired installation location Plug the three way cigarette lighter adaptor 154005 00004 into the tractor s cigarette lighter Plug the car charger for iPad 154005 000002 into the cigarette lighter adaptor and into the iPad a NOTE A battery charge indicator is displayed at the top left corner of the iPad If you desire the iPad may be connected to the charger at all times b NOTE Steps 6 through 8 are optional steps that describe how to install the wire guides Wire guides may be used to help secure the iPad charger cord to the tractor cab such as to the dash Installing the wire guides for the iPad charger cord reduces the chance of the cord becoming tangled or becoming caught by e g the operator s hands Clean the area where you will be placing the wire guides 355005 000004 with the alcohol wipes 359060 000003 Remove and discard the paper backing from the wire guides Place the adhesive side of the wire guides onto the desired location on the tractor cab next to the iPad charger cord Place the iPad charger cord into the hook of the wire guide Page 17 of 55 600840 000019 Revision 1 1 Last Revised December 13 2011 Wireless Blockage Monitor Installation Manual 2 4 Installing the access point About the access point The access point allows the Wireless Blockage Monitor app to communicate with the ECUs The access point must be powered on in order for the Wireless Blockage
28. d procedures None Installation location Not applicable To rename an ECU 1 3 4 o Press the Configure icon on the Wireless Blockage Monitor app home screen Press Configure on the Configuration Summary screen Press the first manifold name on the list on the Edit Current Configuration screen Press the Manifold Name field which is currently the ECU s serial number on the Edit a Manifold screen An on screen keyboard will display Using the on screen keyboard type the desired ECU name IAS recommends naming the ECU 7 or Manifold 1 Press Save a NOTE To access the numeral keys press the 2123 button on the on screen keyboard Repeats Steps 4 through 6 for all of the ECUs installed on the system naming the manifolds respectively i e name the second manifold on the list 2 or Manifold 2 EXAMPLE If an air seeder contains four manifolds and the operator has renamed the manifolds folding the procedure above the manifolds will display on the Blockage screen of the Wireless Blockage Monitor app with Manifold 7 on the far left of the screen and Manifold 4 on the far right of the screen When viewing these manifolds in real life while facing the tractor the numbers will correspond with the Blockage Monitor screen with the manifold labeled 1 being located on the far left of the air seeder and the manifold labeled 6 being located on the far right of the air seeder This example is illustrated in Figure 24 Page 47 o
29. downloaded to the iPad o In order to ensure that the access point is operating correctly after installation of the access point you must have the app downloaded to the iPad Other related procedures e Downloading the Wireless Blockage Monitor app on the iPad o The access point must be installed prior to the Wireless Blockage Monitor app being able to communicate with the rest of the Wireless Blockage Monitor system Installation location The access point should be installed in the tractor cab so that it is protected from foreign material such as dust and dirt IAS recommends installing the access point on the tractor cab s mounting bar if available directly behind where the iPad mounting bracket is installed If this is not possible chose an installation location that would not hinder the operator s daily activities within the cab and where the access point would not be likely to become damaged NOTE Window mounting kits are available Contact IAS for purchase details or for more information To install the access point 1 Remove the cover from the back of the access point assembly 150570 000002 by pushing the tab up and sliding the cover off 2 Plug the three way cigarette lighter adaptor 154005 000004 into the tractor s cigarette lighter if you have not done so already 3 Connect the access point power cable 355020 000031 to the port labeled LAN on the back of the access point assembly and the cigarette lighter adaptor
30. e way cigarette 454005 000004 1 Tractor kit lighter adaptor Varies Wire guides optional 355005 000004 6 included with Tractor kit kit GE 359060 000003 1 Tractor kit optional 153025 000024 May not be included iPad if included with the p with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 10 Parts needed to install the iPad mounting bracket Tools needed to install the iPad mounting bracket 7 16 socket Number of times procedure is performed Once per Wireless Blockage Monitor system Steps that must be completed prior to this procedure None Page 16 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Other related procedures Downloading the Wireless Blockage Monitor app on the iPad Installation location IAS suggests installing the iPad mounting bracket onto the mounting bar as shown in Figure 3 in the tractor cab if one is available The iPad mounting bracket however may be installed anywhere in the tractor cab where it would be easily visible and within reach of the operator during air seeder operation To install the iPad mounting bracket 1 2 3 Insert the ball of the 3 5 tablet iPad mount arm into the back of the tablet iPad mount 352004 000002 Connect the rail attachment for tablet iPad mount 352004 000004 to the bottom of the mount arm Connect the rail attachment to the tra
31. embly 150505 000001 onto the front of ECU mounting bracket 351050 000012 a NOTE Do not remove the locknuts currently on the ECU assembly 2 Secure the ECU assembly to the mounting bracket by placing four 1 4 20 steel locknuts 352011 000040 and four 14 steel washers 352012 000024 to the back of the existing bolts on the ECU Figure 14 ECU installed on an air seeder tower NOTE ECUs are displayed in alphabetical numeric order on the Blockage screen of the Wireless Blockage Monitor app By default the ECUs will be labeled with their serial numbers Serial number labels are located on the back of the ECUs the same side as the flow sensor ports Refer to Section 2 12 for instructions on how to rename the ECUs in the Wireless Blockage Monitor app so that they may be easily identified when troubleshooting a blockage Page 32 of 55 AZ Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 8 Installing flow sensors About flow sensors Flow sensors directly connect to the air seeder s runs They are able to detect when seed or other material such as fertilizer is flowing through the run due to the sound that is produced when the material when the material strikes against the flow sensor When no sound is recorded by the flow sensor and the air seeder is in the ground the Wireless Blockage Monitor app will notify the operator of a potentially blocked run via an audio alarm
32. et the work switch should be approximately 1 4 from the magnet but should not touch it 4 Replace the nut removed in Step 1 so that the work switch is secured to the bracket Page 24 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To install a work switch on an air seeder if no existing work switch is present NOTE These instructions are for installing a work switch on an air seeder where no work switch was previously installed on the implement If you have difficulty determining where the work switch should be installed please contact IAS for assistance 1 Determine the location of the hydraulic cylinders that are used to lift the air seeder implement in and out of the ground at the end of the rows 2 Determine a location where the work switch and magnet may be mounted so that they will be moved apart on the hydraulic cylinder when the air seeder is out of the ground 3 Follow Steps 1 through 7 of the To install a work switch on an air seeder instructions Since no work switch was previously present you may need to drill into the air seeder frame for the work switch bracket bolts or zip tie the work switch bracket onto the hydraulic cylinder 4 Follow the instructions given in Section 2 11 to ensure that the work switch has been properly installed Work switch Figure 11 A work switch installed on an air seeder where no bracket previously existed In the figure
33. f 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Work Switch Settings History Blockage Z Configure Figure 23 Renaming the ECUs example Top Tractor connected to a six manifold air seeder Bottom Blockage screen representing that air seeder 2011 Intelligent Agricultural Solutions All Rights Reserved Page 48 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Appendix A Wiring harness diagrams per air seeder configuration The graphics on this and the following pages are suggestions for ways wiring harnesses may be installed Each graphic is specific to the number of manifolds on an air seeder Please note that due factors such as difference in manifold spacing wiring harness set up may differ from that shown in these diagrams Two and Three Manifold Wiring Harness Diagrams Tractor Manifold ECU Work switch 3 amp outlet 3 way splitter Tractor harness Intermediary harness ECU harness Master ECU harness Page 49 of 55 Figure 24 Two 2 manifold wiring harness Figure 25 Three 3 manifold wiring harness Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Four and Five Manifold Harness Diagrams Tractor Manifold ECU Work switch 3 amp outlet 3 way splitter Tractor harness In
34. g the account setup if you do not wish to enter a credit card number To download the Wireless Blockage Monitor app NOTE This step is only required if your iPad was not included with the Wireless Blockage Monitor or if you have signed out of the default Apple ID on a preconfigured iPad and signed in with a different Apple ID 1 Connect the iPad to a WiFi network a NOTE The Wireless Blockage Monitor access point does not provide access to the Web so therefore you must be connected to a different internet connection such as a home WiFi network Please contact IAS for assistance if you do not have access to a WiFi network 2 Onthe iPad s home screen press the App Store icon a NOTE You may need to press the iPad s home button to view the screen with the App Store icon Press the Search field in the top right corner of the App Store screen An on screen keyboard will appear Type wireless blockage monitor and press the Search button When you see the IAS Wireless Blockage Monitor app press it Press the Free button Press INSTALL APP Follow the on screen instructions to finish downloading the app w o N O oE Page 14 of 55 Sal Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To download additional free apps on a preconfigured iPad NOTE These instructions only apply to users who wish to download additional free apps other than the Wireless Blockage Monitor app onto their
35. h bracket on top of an existing work switch bracket 23 Figure 9 Installing the work switch onto the bracket u u sssseeeeererer ennen rr ner 24 Figure 10 Adjusting the work switch length ecccceeeeeeeee eee ennen 24 Figure 11 A work switch installed on an air seeder where no bracket previously existed 25 Figure 13 The back left and front right sides of the EC ENNEN 30 Figure 14 Mounting a ECU bracket to the air Seeder ower 31 Figure 15 ECU installed on an air Seeder Tower 32 Figure 16 Flow sensors installed on a manifold sssneeeeereeerererrr ennen 33 Figure 17 Installing a flow Sensor EEN 34 Figure 18 Order to connect flow sensors to ECU ENNEN 37 Figure 19 Installing the ECU ekugedleszuguekuskuzgeiuaesgeun EES rr 38 Figure 20 Automatic Configuration screen ENNEN 39 Figure 21 Edit Current Configuration screen 41 Figure 22 Edit a Manifold screen E 42 Figure 23 The Edit a Manifold SEENEN Ehe 46 Figure 24 Renaming the ECUS example kee 48 Figure 25 Two 2 manifold wiring harness E 49 Figure 26 Three 3 manifold wiring harness sssseseeerereenne renerne 49 Figure 27 Four 4 manifold wiring harness ke 50 Figure 28 Five 5 manifold wiring harness ke 50 Figure 29 Six 6 manifold wiring harness scccececweicsecivadeetennssdendeetiastecnsinebientiviaseencnasenieveasvesdeaes 51 Figure 30 Seven 7 manifold wiring harness AEN 51 Figure 31 Eight
36. ibed in Section 2 5 1 2 3 Ensure the iPad is connected to the Wireless Blockage Monitor WLAN Open the Wireless Blockage Monitor app on the iPad Power on the tractor and connect the air seeder if you have not already done so Adjust the air seeder s hydraulic system so that the implement is in the ground Press the Blockage icon on the Wireless Blockage Monitor app s home screen Note the color of the circle next to Work Switch on the top left corner of the Blockage screen henceforth referred to as the Work Switch circle The Work Switch circle should be green at this time Adjust the air seeder s hydraulic system so that the implement is out of the ground Note the color of the Work Switch circle It should have changed to gray Adjust the air seeder s hydraulic system so that the implement is in the ground again The Work Switch circle should have changed to green a If the Work Switch circle is not the correct color or does not change when you adjust the air seeder s hydraulic system contact IAS for assistance To ensure work switch has been correctly installed non default method NOTE The default and non default work switch methods are described in Section 2 5 1 Ensure the iPad is connected to the Wireless Blockage Monitor WLAN gt Open the Wireless Blockage Monitor app on the iPad 2 Power on the tractor and connect the air seeder if you have not already done so Adjust the air seeder s hydraulic system so
37. ie 355032 000003 25 V4 Steel Washer 352012 000024 6 Cotter Pin 3 32 diameter 352015 000011 4 22 foot ECU Harness 355020 000020 1 Table 6 ECU Kit Subcomponents Quantity Part Name Part Number included per kit 3 Way DTM Splitter 355030 000002 1 27 foot Intermediary 355020 000019 i Harness Table 7 Intermediary Harness Kit Subcomponents Part Name Part Number SET included per kit Ball Mount with Long Arm amp D Diamond 352004 000005 1 Bases Suction Cup Base with Twist 352004 000006 2 Lock Table 8 Access Point Window Mounting Kit optional Page 10 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 1 3 Tools Required In addition to the parts included in the installation kit you will need the following tools for the installation of the Wireless Blockage System Standard wrench and socket sets Pliers Cordless drill and or flathead screwdriver optional Paint pen or other permanent marking tool optional 1 4 Technical Assistance If you require support during any step of the Wireless Blockage Monitor Installation process please contact IAS using the information below IAS technical support is available from 8 a m to 5 p m Central Time Monday through Friday During planting season April through June these hours are expanded to 7 00 a m to 12 00 midnight Central Time Sunday through Saturday IAS is closed during some federal United States h
38. igure 9 8 Adjust the locknuts on the work switch assembly so that the work switch is within one forth inch 1 4 of the work switch magnet when the work switch is engaged refer to Figure 10 Refer to the To adjust work switch length instructions for specific detail on this step a CAUTION The work switch should not touch the magnet If the work switch touches the magnet it make cause damage to the Wireless Blockage Monitor switch Figure 8 Installing the work switch bracket on top of an existing work switch bracket Existing work switch bracket is shown attached to a hydraulic cylinder Page 23 of 55 YW Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Figure 10 Adjusting the work switch length In order to get the work switch the correct distance from the magnet you must adjust the length the work switch sticks out of the work switch bracket The left image shows the work switch with a short length sticking out of the work switch bracket The right image shows a longer length sticking out of the work switch bracket To adjust the length the work switch bracket 1 Remove the nut from the work switch bolt that is in front of the work switch bracket 2 Screw the remaining nut on the work switch into the correct position further from or closer to the bracket 3 Adjust the work switch bolt until it is the correct distance from the work switch magn
39. ity Number of ECUs Found 4 Number of Ports Found 80 Figure 19 Automatic Configuration screen Part Name Part Number eee Contained within 153025 000024 May not be included iPad if included with the 1 with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 18 Parts needed to configure the Wireless Blockage Monitor system Tools Needed None Number of times procedure performed Once per Wireless Blockage Monitor system Page 39 of 55 al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Steps that must be completed prior to this procedure e Download of the Wireless Blockage Monitor app to the iPad Section 2 2 Installation of the access point Section 2 4 Installation of the work switch Section 2 5 Installation of the wiring harness Section 2 6 Installation of the ECUs Section 2 7 Installation of the flow sensors Section 2 8 Connection of the flow sensors to the ECU Section 2 9 Tractor must be powered on Tractor must be connected to the air seeder Other related procedures e Configuring the work switch Section 2 11 o After the overall Wireless Blockage Monitor system has been configured the work switch must also be configured to ensure that it has been correctly installed and to ensure that it is communicating correctly with the Wireless Blockage Monitor app e Renaming the ECUs in the Wireless Blockage Monit
40. ld Hp gt S gt Se i sm amp Ze 9 Kl Ah SN Figure 17 Order to connect flow sensors to ECU Page 37 of 55 600840 000019 Revision 1 1 Wireless Blockage Monitor Installation Manual Last Revised December 13 2011 To install ECU shields Press a ECU bracket shield 351050 000012 into one of the side of the ECU mounting 1 bracket 351050 000012 2 Secure the ECU bracket shield to the mounting bracket with two cotter pins 352015 000011 one on the top of the bracket and one on the bottom of the bracket 3 Press a ECU bracket shield onto the other side of the ECU mounting bracket 4 Secure the ECU bracket shield to the mounting bracket with two cotter pins Using a pliers blend the cotter pins down Figure 18 Installing the ECU shields Page 38 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 10 Configuring the Wireless Blockage Monitor About configuring the Wireless Blockage Monitor Configuring the Wireless Blockage Monitor system allows for the Wireless Blockage Monitor app to detect the newly installed ECUs The Wireless Blockage Monitor must be configured after installation of the Wireless Blockage Monitor system and also configuration of the runs have changed e g from using all runs for seeding to blocking every other run 1 29 PM Automatic Configuration Installation Summary 3 lt Detecting Hardware With Activ
41. ll onto the iPad from the app store a To access the app store press the App Store icon on the iPad s home screen WARNING Since downloaded apps are retained to an Apple ID the Wireless Blockage Monitor and any other free apps that you may have downloaded while signed in with the preconfigured Wireless Blockage Monitor default account will not carry over when you sign into the iPad with a different Apple ID For information on how to download the Wireless Blockage Monitor app while signed into the different Apple ID refer to the To download the Wireless Blockage Monitor app Page 15 of 55 Revision 1 1 YW Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 2 3 Installing the iPad mounting bracket About the iPad mounting bracket The iPad mounting bracket serves as a Safe place to rest the iPad during air seeding and also allows the operator to view the Wireless Blockage Monitor app at a glance The mounting bracket is ruggedized meaning that it will absorb some of the bumps and jolts typical during air seeding Figure 3 An iPad mount attached to a tractor s mounting bar Quantity g Ges Part Name Part Number needed Contained within Tablet iPad Mount 352004 000002 1 Tractor kit 35 Tablet Fag 352004 000003 1 Tractor Kit Mount Arm Rail attachment for Tablet iPad mount 352004 000004 1 Tractor kit Car charger for iPad 154005 000002 1 Tractor kit Thre
42. n 1 per Kit 153025 000018 manifold See Table 7 Not required for air seeders with less than 3 manifolds Air seeders with less than 4 manifolds 1 Air seeders with less than 4 manifolds with seed cart between 2 i Air seeders with Deutsch Sealing Plug 153560 000015 more aad manifolds None needed Air seeders with more than 4 manifolds with seed cart between 1 Access Point Window Mount Kit 153025 000022 EE See Table 8 p iPad with WBM App 1 per system Installed EE optional Table 1 Kit list for installation Part Name Part Number E Kit 1 25 Hose Clamp 352013 000005 2 Adaptor Hose 351060 000008 1 Sensor Assembly 153570 000015 1 Table 2 Standard Sensor Kit Subcomponenis for 1 25 hoses Part Name Part Number SE Kit 1 25 Hose Clamp 352013 000005 4 Adapter Hose 351060 000008 2 Sensor Assembly 153570 000015 1 Table 3 Nonstandard Sensor Kit Subcomponents for 1 hoses Page 8 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Page 9 of 55 Part Name Part Number Quantity included per Kit Tractor Harness 355020 000021 1 Access Point 150570 000002 1 Access Point Power Cable 355020 000031 1 Car charger for iPad 154005 000002 Tablet iPad mount 352004 000002 3 5 Tablet iPad Mount Arm 352
43. ness does not need to be fully extended to reach the ECU coil the harness around a hydraulic line or electrical wire before securing to the air seeder using the 7 9 cable ties Using 7 9 cable ties 355032 000004 secure the ECU harness to the air seeder To connect a Master ECU harness to an intermediary harness NOTE The ECU that is deemed as the Master ECU is the one closest to the work switch installation location Typically this is near or in the middle of the air seeder implement Refer to the appropriate graphic in Appendix A to help you determine which ECU on your air seeder would be considered the Master ECU NOTE This procedure may only be performed after the ECU deemed as the Master ECU is installed See Section 2 7 1 2 Follow Steps 1 and 2 of the To connect an ECU harness to an intermediary harness instructions Plug the 2 pin gray and orange connector of the work switch s 153560 000014 harness into the 2 pin receptacle of the ECU 150505 000001 you have designated as the master ECU Using 7 9 cable ties 355032 000004 secure the Master ECU harness to the air seeder Page 29 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 7 Installing ECUs About the ECU The Electronic Control Unit ECU allows for the flow measurement data recorded by the flow sensors to be communicated with the Wireless Blockage Monitor om d oe o
44. nto each end of the adapter hose a NOTE IAS recommends placing the sides of the hose clamp containing the fastening screw on the same side in order to reduce the amount of space taken up by the system This is especially true for air seeder systems where final runs are very close together 3 Tighten the hose clamp that attaches the adapter hose and the sensor assembly using a 5 16 socket a 5 16 nut driver on a cordless drill or a flathead screw driver Leave the hose clamp that will eventually face the manifold loose at this point 4 Detach the final run hose from the manifold 5 Place the flow sensor onto the manifold where the final run hose previously attached 6 Tighten the hose clamp facing the manifold using a socket cordless drill or a flathead screwdriver so that the adaptor hose is secured on the manifold 7 Attach the final run hose to the bottom of the sensor assembly a NOTE For a better fit you may want to cut off approximately 2 inches from the hose length before reattaching to manifold 8 Tighten the hose clamp that attaches the sensor assembly to the final run hose using a 5 16 socket a 5 16 nut driver on a cordless drill or a flathead screw driver a NOTE This hose clamp should be original to the air seeder implement and is not included in the Wireless Blockage Monitor installation kit If you need additional hose clamps please contact IAS for purchase information 9 Repeat this step for every final run on your air
45. olidays Telephone 701 356 9222 E mail support intelligentag com Page 11 of 55 Revision 1 1 WY Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 2 Installation Instructions 2 1 Overview Checklist The Wireless Blockage Monitor installation is accomplished in the following steps O Download the Wireless Blockage Monitor app O Install the iPad mounting bracket O Install the access point O Install the work switch O Install the wiring harness O Install the ECU O Install the flow sensors O Connect the flow sensors to the ECUs O Configure the Wireless Blockage Monitor O Configure the work switch Ol Rename the ECUs in the Wireless Blockage Monitor app access point and iPad mounted in cab wiring harnesses work switch N ECUs mounted x on tower below Ze manifold Flow sensors mounted on runs coming from manifold Figure 1 Installation location overview The wiring harness in this figure is specific for a three manifold air seeder For more wiring harness diagrams refer to Appendix A of this document Page 12 of 55 600840 000019 Revision 1 1 Last Revised December 13 2011 Wireless Blockage Monitor Installation Manual 2 2 Downloading the Wireless Blockage Monitor app Work Switch Settings History Figure 2 A screenshot from the Wireless Blockage Monitor app About the Wireless Blockage Monitor App The Wireless Blockage Monitor app is
46. onitor app If you desire that the ECUs be displayed in the order that they are installed ensure that you have named the ECUs in alphabetical numeric order see Figure 24 for an illustrated example Edit a Manifold Editing Manifold Name 0000 00001 Part Number 110375 0001 0000 00001 Firmware Version 1 0 0 0 0000 00001 Port 1 vi Serial Number 0000 00001 Port 2 vj 0000 00001 Port 3 v J 0000 00001 Port 4 v j 0000 00001 Port 5 As 0000 00001 Port 7 d J 0000 00001 Port 8 0000 00001 Port 9 0000 00001 Port 6 D 0000 00001 Port 10 Figure 22 The Edit a Manifold screen Part Name Part Number Reon Contained within 153025 000024 May not be included iPad if included with the with the Wireless Wireless Blockage Blockage Monitor Monitor system system Table 20 Parts needed to rename the ECUs in the Wireless Blockage Monitor app Tools Needed None Number of times procedure performed Once per manifold Page 46 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Steps that must be completed prior to procedure Download the Wireless Blockage Monitor app Section 2 2 Install the access point Section 2 4 Install the wiring harnesses Section 2 6 Install the ECUs Section 2 7 Configure the Wireless Blockage Monitor Section 2 10 Other relate
47. or app Section 2 12 Installation location Not applicable To auto configure the Wireless Blockage Monitor 1 Ensure iPad is connected to the Wireless Blockage Monitor WLAN Open the Wireless Blockage Monitor app on the iPad Power on the tractor and connect the air seeder if you have not done so already Press the Configure icon on the left side of the Wireless Blockage Monitor app screen Press Auto Configure Ensure the correct number of ECUs have been detected by the Wireless Blockage Monitor app If the correct number of ECUs have not been detected refer to the To manually add an ECU instructions 6 Allow seed to run through the air seeder while monitoring the Automatic Configuration screen on the iPad for a few seconds The sound produced by the seed hitting the flow sensors will allow the Wireless Blockage Monitor app to automatically detect them 7 The number of ECUs and runs ports detected by the Wireless Blockage Monitor will appear If the number does not correctly match the total number of manifolds and runs on your air seeder follow the To manually configure the Wireless Blockage Monitor instructions below a NOTE You must follow the To change which ECU is labeled Master ECU instructions given later in this section as the Master ECU is not automatically recognized during the auto configure process R N Page 40 of 55 Ko Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised
48. preconfigured iPad These instructions do not apply to users with preconfigured iPads who have signed out of the default account or who have changed the password of the default account 1 Select the free app you d like to download from the app store on the iPad a To access the app store press the App Store icon on the iPad s home screen 2 Press the Free button and press Install App 3 You will be prompted to provide a password Ensure that the e mail that is displayed is ias iPad serial number intelligentaguser com This is the e mail associated with the default account and should automatically appear 4 Type Pswd1234 into the password field and press OK Once it has finished downloading the app will appear on the iPad s home screen To download non free apps on a preconfigured iPad NOTE These instructions only apply to users who wish to download non free apps onto their preconfigured iPad These instructions do not apply to users who have already signed out of the default account and signed in with their own Apple ID 1 Since the preconfigured default account does not allow for the download of non free apps you must sign out of the account To sign out a From the iPad s home screen press the Settings icon b Press Store from the left column c Press Sign Out 2 Sign into the iPad with an existing Apple ID or create a new Apple ID a Refer to Creating an Apple ID instructions above 3 Download the non free app you wish to insta
49. r permanent marking tool optional Number of times procedure performed Once per manifold Steps that must be completed prior to procedure e Installing the ECUs Section 2 7 e Installing the flow sensors Section 2 8 Other related procedures e Configuring the Wireless Blockage Monitor Section e Renaming the ECUs Installation location The flow sensor tubes located on each run will be connected to the ECU installed on tower installed directly underneath the manifold Page 36 of 55 al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To connect flow sensors to the ECU 1 Remove the same number of caps from ECU for the number of runs on the manifold Leave the caps on the unused connectors to prevent foreign material from entering the ECU a EXAMPLE If the manifold contains 16 runs remove caps from ports 1 through 16 and leave the caps on ports 17 through 24 2 Remove and discard the cap at the end of the flow sensor tube of the run that is immediately left of the manifold post when facing the tractor run labeled 1 in Figure 17 3 Run that flow sensor tube through the hole on the top of the ECU mounting bracket 351050 000012 4 Attach the flow sensor tube to the port labeled 1 on the ECU 5 Secure the flow sensor tube to the ECU port by placing a miniature cable tie 355032 000003 around the bottom of where the flow sensor tube and ECU port connec
50. seeder Once all of the flow sensors have been installed on a manifold you may proceed to the instructions in Section 2 9 Connecting flow sensors to the ECU A picture showing flow sensors installed on all of the final runs of an air seeder is shown in Figure 15 Figure 16 Installing a flow sensor Page 34 of 55 YW Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To install air flow sensors on 1 diameter final run hoses If your air seeder final run hoses have a 1 diameter instead of the 1 25 diameter you must complete the following steps in order to install the flow sensors Part Name Part Number Quantity Contained within needed 1 25 Hose Clamp 352013 000005 4 run Nonstandard sensor kit Adaptor Hose 351060 000008 2 run Nonstandard sensor kit Sensor 153570 000015 1 run Nonstandard sensor kit Table 16 Parts needed to install flow sensors on nonstandard 1 diameter final runs eos Complete Steps 1 through 3 of the To install the flow sensor instructions Cut an approximately 2 inch piece from the end of the final run hose Place the 2 inch hose piece back onto the manifold Attach the adapter hose 351060 000008 to the 2 inch hose piece Tighten the hose clamp that connects the adapter hose to the 2 inch hose piece using a 5 16 socket a 5 16 nut driver on a cordless drill or a flathead screw driver D
51. stalled incorrectly Check the equipment and ensure that it has been installed correctly If you continue to have problems contact IAS for assistance Edit a Manifold Editing Manifold Name 0000 00001 Part Number 110375 0001 Serial Number 0000 00001 Firmware Version 1 0 0 0 0000 00001 Port 1 v T 0000 00001 Port 2 v 0000 00001 Port 3 IS oT 0000 00001 Port 4 y 0000 00001 Port 5 y Cate A 0000 00001 Port 6 IS 0000 00001 Pont 7 v 0000 00001 Port 8 v 0000 00001 Port 9 d 0000 00001 Port 10 y Figure 21 Edit a Manifold screen To manually delete an ECU 1 Press the Configure icon on the Wireless Blockage Monitor app s home screen 2 Press Configure on the Configuration Summary screen 3 Press the trash can icon located on the upper left corner of the gray box in the middle of the screen 4 Press the name of the manifold ECU you would like to delete on the Edit Current Configuration screen Page 42 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To manually delete a flow sensor 1 2 3 4 Press the Configure icon on the Wireless Blockage Monitor app s home screen Press Configure on the Configuration Summary screen Press the name of the manifold ECU where the extra flow sensor s are located on the Edit Current Configuration screen Using the drop down menu immediately to
52. t and tighten the miniature cable tie a CAUTION Ensure that the flow sensor tube is not kinked especially where the tube comes through the top of the ECU bracket and where the tube is secured to the ECU with the miniature cable tie If a flow sensor tube becomes kinked the ECU will be unable to receive any blockage measurement readings from that run 6 Optional Mark the number of the port the flow sensor hose is attached to Example 7 somewhere easily visible on the flow sensor hose using a paint pen or other marking tool a NOTE When the Wireless Blockage Monitor detects that a run is blocked the Wireless Blockage Monitor app will display the number of the ECU port that that run is attached to Marking the number of the port the flow sensor is attached to will allow you to easily identify a blocked run during troubleshooting 7 Continue removing the caps from the ends of the flow sensor tubes running them through the top of the ECU bracket and attaching them to the proper ECU port continuing to work counterclockwise around the manifold as shown in Figure 17 8 Secure the ECU caps to all of the unused ports using the miniatures cable ties a IMPORTANT If the caps are removed from unused ports or if the caps are not secured to the port the Wireless Blockage Monitor app may incorrectly read that a flow sensor is attached to the port during the automatic configuration process Towards tractor i E Top of Y nee ekl T Manifo
53. termediary harness ECU harness Master ECU harness Page 50 of 55 Figure 27 Five 5 manifold wiring harness Tractor Manifold ECU Work switch 3 amp outlet 3 way splitter Tractor harness Intermediary harness ECU harness Master ECU harness Page 51 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Six and Seven Manifold Harness Diagram O ne mg ap SO po Figure 28 Six 6 manifold wiring harness O Figure 29 Seven 7 manifold wiring harness Page 52 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Eight Manifold Wiring Harness Diagram Se Tractor e d Manifold ECU all H w GZ i BEE e Work switch E gg eee a tien P 3 amp outlet fe a Ben 3 way splitter SE a Tractor harness D we w RN Intermediary Men ZE harness s m ECU harness a O Master ECU harness Figure 30 Eight 8 manifold wiring harness Tractor Manifold ECU Work switch 3 amp outlet 3 way splitter Tractor harness Intermediary harness ECU harness Master ECU harness Page 53 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Nine Manifold Wiring Harness Diagram Figure 31 Nine 9 manifold wiring harness Page 54 of 55 Tractor Manifold EC
54. termediary manifolds Master ECU kit and or H 355020 000019 2 Intermediary Harness arness kit For air seeders with four or more manifolds Two less than the number of manifolds One less than 1 manifold 22 foot ECU Harness 355020 000020 due to Master ECU kits ECU harness 22 foot ECU Harness One per _Warkswitch 355020 000018 system Master ECU kit 7 9 Cable Tie 355032 000004 APProxmately Master ECU Varies depending on Deutsch Sealing Plug 153560 000015 Deutsch Sealing Plug air seeder configuration Table 13 Parts needed for installing the wiring harnesses Page 26 of 55 al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 Tools needed e Pliers optional Number of times procedure performed e Tractor harness installation procedure once per Wireless Blockage Monitor system e Intermediary harness installation procedure o Once for air seeders with two manifolds o Two for air seeders with three manifolds o Two less than the number of manifolds for air seeders with four or more manifolds e ECU harness installation procedure Once per manifold minus one due to the installation of the Master ECU harness e Master ECU harness installation procedure Once per system Steps that must be completed prior to this procedure e Tractor must be connected to the air seeder during installation of the tractor wiring harness e Install
55. th the Wireless Blockage Monitor e Obtaining an iPad e Creation an Apple ID see Creating an Apple ID Page 13 of 55 al Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 For preconfigured iPads e None Other related procedures e Installing the access point Section 2 4 e Configuring the Wireless Blockage Monitor Section 2 10 e Configuring the work switch 2 11 e Renaming the ECUs in the Wireless Blockage Monitor app Section 2 12 Installation location Not applicable Creating an Apple ID NOTE This step is only required for users whose iPads were not included with the Wireless Blockage Monitor and who do not already have an Apple ID or users whose received a preconfigured iPad but wish to download non free apps onto the iPad see To download non free apps on a preconfigured iPad for more information An Apple ID is required for downloading items such as apps from the App Store or songs from iTunes You may use the same Apple ID on different Apple devices such as an iPad and an iPod If you have an existing Apple ID you may use it to download the Wireless Blockage Monitor you are not required to create a new Apple ID For instructions on how to create an Apple ID refer to Apple s support website or contact your dealership for assistance NOTE Since the Wireless Blockage Monitor app is a free app you may select None in the credit card type field durin
56. the right of the flow sensor you wish to delete select Select a port a Check that the remaining flow sensors are connected to the correct port i e Run 1 is attached to port 1 of that ECU Press Save when you have finished deleting the flow sensors from that ECU EXAMPLE If your air seeder has a 16 run per manifold set up but one manifold displays 17 runs select Select a port from the drop down menu immediately to the right of Run 17 Ensure that Runs 1 through 16 are displaying as being connected to the correct ports of the ECU ports 1 through 16 To change which ECU is labeled Master ECU 1 2 3 4 Press the Configure icon on the Wireless Blockage Monitor app s home screen Press Configure on the Configuration Summary screen Using the Master ECU drop down list located at the bottom of the Edit Current Configuration screen select the name of the ECU that is the master ECU Press Save a If you have not yet renamed the ECUs see Section 2 12 the ECUs will be labeled with their serial numbers Page 43 of 55 el Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 2 11 Configuring the work switch About configuring the work switch In order to ensure the Wireless Blockage Monitor work switch has been correctly installed and is correctly communicating with the Wireless Blockage Monitor app you must follow the instructions given in this section P
57. three way splitter 2 Extend the intermediary harness over the air seeder Use the appropriate figures in Appendix A to help guide the placement of the intermediary harness a NOTE If the intermediary harness does not need to be fully extended to reach where it must connect coil the harness around a hydraulic line or electrical wire 3 Using 7 9 cable ties 355032 000004 secure the intermediary harness to the hitch Page 28 of 55 Wireless Blockage Monitor Installation Manual 600840 000019 Revision 1 1 Last Revised December 13 2011 To connect an ECU harness to an intermediary harness NOTE Only two ECU harnesses may be connected to each intermediary harness 1 3 Connect the black connector at the end of the ECU harness 355020 000020 to a three way splitter of an intermediary harness 355020 000019 a NOTE If only one wiring harness intermediary ECU or Master ECU will be connected to the three way splitter of the intermediary harness insert a Deutsch sealing plug 153560 000015 into the remaining receptacle of the three way splitter to prevent foreign material from entering the three way splitter Refer to the appropriate figures in Appendix A to determine if two wiring harnesses will be connected to the intermediary harness s three way splitter Extend the ECU harness so that it reaches an air seeder tower Use the appropriate figures in Appendix A to help guide the placement of the ECU harness a NOTE If the ECU har
58. tor app NOTE This procedure only has to be performed if the work switch uses the non default method as described in the About work switch methods section above 1 Open the Wireless Blockage Monitor app on your iPad by pressing the icon on your iPad s home screen if the app is not already open 2 Press the Configure icon located in the left column of the screen 3 Press Configure 4 Onthe Edit Current Configuration screen drag the gray box next to Work Switch Reversed on the bottom of the screen to the right so that ON is shown The change will automatically be saved Page 21 of 55 Revision 1 1 YW Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 Part Name Part Number peel Contained within a veil Switch 359035 000001 1 Master ECU kit agnet 1 4 20x12 Steel Bolt 352010 000084 2 Master ECU kit 1 4 Steel Washer 352012 000024 4 Master ECU kit 1 20 Steel Locknut 352011 000040 2 Master ECU kit Work Switch Bracket 351050 000016 1 Master ECU kit Work Switch Assembly 153560 000014 1 Master ECU kit Table 12 Parts needed to install work switch Tools needed to install work switch e Standard wrench set Number of times procedure is performed Once per Wireless Blockage Monitor system Steps that must be completed prior to this procedure e Download the Wireless Blockage Monitor app on the iPad Section 2 2 e Installation of the access point
59. tor app when the air seeder implement is in or out of the ground The audible alarms that would typically signal when air flow in a run is blocked will automatically be silenced when the work switch is disengaged i e out of the ground NOTE When the air seeder is out of the ground the Wireless Blockage Monitor app will display that all runs are blocked as no air or material is flowing through the runs but the audio alarm will not sound Figure 7 Wireless Blockage Monitor work switch assembly About work switch methods Air seeder work switches use one of two methods to determine when the implement is in the ground engaged 1 Default method the work switch is engaged magnet is close to the work switch when the air seeder is in the ground Likewise the work switch is disengaged magnet and work switch are apart when the air seeder is out of the ground 2 Non default method the work switch is disengaged when the air seeder is in the ground Likewise the work switch is engaged when the air seeder is out of the ground You may want to install the Wireless Blockage Monitor work switch near the air seeder s existing work switch if one exists If the work switch is installed using the second non default method follow the steps in To reverse the work switch option in the Wireless Blockage Monitor app after you have configured the Wireless Blockage Monitor To reverse the work switch option in the Wireless Blockage Moni
60. ui 7 ke oe oe oe 8 Figure 12 The back left and front right sides of the ECU Quantity me Part Name Part Number eee Contained within ECU 150505 000001 manod Master e ECU Mounting 351050 000012 manitol Master ECU and ECU Bracket kits 14 20 Steel Locknut 352011 000040 4 manitold Master Et ana ECU 14 Steel Washer 352012 000024 4 manifold Master a tale EGY Ubolts with Saddle 2 diameter U bolt Clamp Options for 352013 000006 ECU mounting 2 5 diameter U bolt Ubolts with Saddle bracket 352013 000007 i Clamp not packaged 3 diameter U bolt 2 manifold with a kit due to Size of manifold 352013 000008 variance in size determines size of U bolt 4 diameter U bolt needed 352013 000009 Tools needed Standard socket set Table 14 Parts needed to install the ECU Number of times procedure performed Once per manifold Page 30 of 55 Revision 1 1 YW Wireless Blockage Monitor Installation Manual 600840 000019 Last Revised December 13 2011 Steps that must be completed prior to this procedure e Installing the work switch Section 2 5 e Installing the wiring harness Section 2 6 Other related procedures e Downloading the Wireless Blockage App Section 2 2 Installing the access point Section 2 4 Installing the flow sensors Section 2 8 Connecting the flow sensors to the ECU Section 2 9 Renaming the ECUs in the Wireless Blockage Monitor app Se

WIRELESS BLOCKAGE MONITOR INSTALLATION MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents