OzFlarm Installation Manual
Contents
1. Ozfl Am INSTALLATION MANUAL OzFLARM Situation Awareness UNIT Status FLARM Software Version 3 07 March 2007 OzFLARM Software Version 1 005 Jan 2006 2003 2006 FLARM Technology 2005 2006 RF Developments Pty Ltd Boonah Queensland Australia Wwww rf developments com INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Version Control 1 0 1 01 1 02 1 03 1 04 Initial release Revised Power up sequence notes OZFALRM software now 1 004 Include version 2 hardware references Tidy up power connection references Correct dataport wiring mistakes Version 1 03 Page 2 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT 1 Welcome to the community of FLARM users Thank you for purchasing OzFLARM a modern low cost situation awareness unit for sailplanes and light aircraft The main task for OZFLARM is to support the pilot while the pilot scans the airspace ahead with his own eyes FLARM is simple to use and does not distract the pilot from the main responsibility in hand Sport flying is an activity that is associated with considerable risks for crew passengers third parties and other objects In order to make full and safe use of OzFLARM it is absolutely essential to be fully aware of the risks operating conditions restrictions and limitations associated with the use of OzFLARM This includes familiarity with and observance of the Operating Manual and this Installation Manual Addition2. linked with Pin 7 inside the unit Chapter 2 7 2 2 7 2 www fai org gliding gnss tech_spec_gnss pdf FLARM uses Pin numbering in line with IGC specifications The usual numbering is in reverse order Version 1 03 Page 5 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT During flight operations at least Pins 2 and 7 must be connected An 8 pole or if necessary 6 pole ribbon cable with an RJ45 push fit connector or an 8 pole twisted pair patch cable with RJ45 adapter are equally suitable A suitable patch cable open at one end is supplied with FLARM and must be configured to the aircraft connector in the aircraft When using an 8 pole cable Pins 122 must be joined Likewise Pins 7 8 If the remaining wires are not used they must be individually insulated and must not be soldered or twisted together not even in pairs Additional note On the supplied cables Blue goes to pin 2 orange white to pin 3 and blue white to pin 5 If making a plug to go to a PDA then use a DB15 male and swap pins 2 and 3 There must be a direct electrical connection between FLARM and the aircraft battery This connection must be secured with a 500 mA fuse Essential electrically operated flight instruments must not draw their power through the FLARM fuse It must be possible for the pilot to interrupt the power supply to FLARM during flight by means of a switch or circuit breaker without affecting other essential aircraft syst
3. can be done using the FLARMtool software FLARM Port Right hand side socket 1 6 to 26 VDC recommended 12 VDC linked with Pin 2 inside the unit 2 6 to 26 VDC recommended 12 VDC linked with Pin 1 inside the unit 3 GPS Data out RS 232 levels NMEA or Ublox sentences 4800BPS GPRMC and GPGGA 4 GND with Pin 7 and 8 linked to the unit 5 Tx OzFLARM transmits data PC side to SUB D9 Pin 2 6 Rx OzFLARM receives data PC side to SUB D9 Pin 3 7 GND negative linked with Pin 8 inside the unit PC side to SUB D9 Pin 5 8 GND negative linked with Pin 7 inside the unit Note You can plug into either dataport with the power connection as they are identical and there is no risk of damaging the unit 8 GPS All Ozflarm units come with an internal GPS antenna which radiates through the top of the housing this means that by just adding power the unit will run with no requirement for an external GPS antenna If you require the use of an external GPS antenna you must do the following Hardware version serial numbers 100 to 199 Remove the 2 housing screws that secure the top lid to the main box you may have to lightly manoeuvre the lid out to clear the rear plastic lenses Locate the GPS board on the top lid you will note 5 screws holding to the lid Remove these carefully note their positions as there are 2 types of screws Looking at the component side of the PCB you will notice a 3 position di
4. earthed to the airframe Installation may only be in a Zone 2A or 3 as described in DO 160E Section 23 10 Sound Signal The front face has a hole to improve the transmission of sound from the internal emitter to the cockpit This hole must remain unobstructed There is no intercom connector The volume control will increase or decrease the audio Third party manufacturers manufacture suitable intercom equipment that is compatible with OZFLARM that can give audable alerts for powered aircraft N 11 Limitations 11 _ Limitations FLARM and OzFLARM are designed and built as a non essential situation awareness only unit to support the pilot and cannot always provide reliable warnings In particular OZFLARM does not give any guidance on avoiding action Under no circumstances should a pilot or crewmember adopt different tactics or deviate from the normal principles of safe airmanship The use of OzFLARM is solely at the discretion of the commander and his crew Operation must be preceded by thorough familiarisation by the commander or his delegated crewmember with the Operating Manual OzFLARM can only warn the pilot of the presence of other aircraft that are also fitted with OZFLARM or compatible equipment or warn of obstructions that are stored in the internal data bank OZFLARM does not communicate with Mode A C S transponders and remains undetected by ACAS TCAS TPAS or Air Traffic Control systems Likewise OZFLARM does not communicate with T
5. for half a second to confirm activation The COMPASS ROSE will be lit up in 45 degree segments The segment pointing NORTH is from 22 5 degrees to 22 5 degrees Other segments line up accordingly Version 1 03 Page 14 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT 0 22 5 North 22 5 67 5 67 5 112 5 112 5 157 5 337 5 360 North Relative Vertical Height Compass Rose Centre LED Vertical Height Horizontal Distance Vertical Height Horizontal Distance Version 1 03 Page 15 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Other Important Planes Rose The Compass Rose will also display position reports for other interesting planes Not all planes in the vicinity will be displayed Horizontal Distance 1000 Meters and Vertical Clearance 300 Meters Outside the above Cylinder GREEN South West 244 296 West 296 334 334 360 Relative Vertical Height DER At least 300m BELOW BELOW Less than 300m MIDDLE At least 300m ABOVE ABOVE iI On Mode Tx rn 9 OzFLARM indicating 1 target between immediate left and the next 45Deg led this means in the area between the 2 This is not necessarily 2 gliders The bottom Led is indicating a glider behind The extreme left centre LED indicates all targets are at the same level 65 metres 180ft Version 1 03 Page 16 of 17 April 1st 2
6. when the cockpit canopy is open lens effect fire hazard Note we recently had units installed on dashes at a comp the outside temp was only 30 degrees C but inside under the plastic the cases were red hot and deformed You must provide a cover or mount under the visor on top of the instrument panel otherwise the plastic WILL distort and cause damage 5 Connectors The red rear face has an MCX socket for an active GPS antenna an RJ45 Power Data Flarm port socket and an RJ45 Extension socket OzFlarm port 6 Power Data The eight pin RJ45 Power Data socket accepts an eight pin connector if necessary a six pin connector that is locked in place The pin connections are largely in line with those set out in IGC GNSS FR Specifications so that the same cables may be used both in the air and on the ground as used for modern IGC compatible flight data recorders The key to the connections is defined by the sequence from left to right not the numbering FLARM Port left hand side socket 1 6 to 26 VDC recommended 12 VDC linked with Pin 2 inside the unit 2 6 to 26 VDC recommended 12 VDC linked with Pin 1 inside the unit 3 FLARM supplies 3 VDC 4 GND with Pin 7 and 8 linked to the unit 5 Tx FLARM transmits data PC side to SUB D9 Pin 2 6 Rx FLARM receives data PC side to SUB D9 Pin 3 7 GND negative linked with Pin 8 inside the unit PC side to SUB D9 Pin 5 8 GND negative
7. 006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Remember OzFLARM is an aid to situation awareness others must be equipped with compatable Flarm OzFLA RM units so spread the word You must continue to use good lookout and fly safely Version 1 03 Page 17 of 17 April 1st 2006
8. ALLATION MANUAL OzFLARM COLLISION WARNING UNIT Controls Note Initial design allowed the user to manually turn ON or OFF the unit by holding the toggle UP for one second This feature has now been disabled as it was not practical for remote installations and also 1n some circumstances the pilot could accidently remove power and the unit would be disabled like when switching from battery one to two The unit now power up when power is applied with the green leds all lighting and a 2000 hz tone and the red leds lighting and a 1800 Hz tone this test all the leds and sounds the two tones used Alarm Rose When ALARM messages are displayed on the Compass Rose they are ALWAYS RED A number of Alarm Levels exist Time to Projected Impact Alarm Level Audible Alarm 8 10 Seconds 3 Ye Yes 13 15 Seconds 2 Yes No 18 20 Seconds M w gt 20 Seconds No No The Alarm will sound under the following conditions e Alarm Level increases e Relative Heading changes by more than 30 degrees since the last report even though the Alarm Level has not changed This is an indicator that a 2 plane is in the area and it is more dangerous at the moment Alarm Acknowledge The alarm is acknowledged by pressing the switch to the MODE position momentarily If you wish to silence the alarm for about five minutes this can be done by pressing the switch to the MODE position for about two to 3 seconds All the LEDS will light up green
9. Belo To G Ozfidm ke e The LED s ON OFF Flashing GREEN Input Voltage is within normal limits at 1 Hz mE Flashing RED at Input Voltage is OUTSIDE normal limits 1 Hz Of The unit is turned OFF GPS Steady RED GPS does not have LOCK Unit will not transmit OFF jGPShsaslockiftheunitis poweredup __ it does not have GPS lock The unit is NOT receiving any other FLARM or OZ FLARM units but is ready for use m E E o aircraft that may be of interest meme usines below the aircraft Pen o inove below or on Te same idee o o above below or on the same flight level FLARM s range is subject to the antenna installation in the aircraft but usually is around 1 to 3 km sufficient even for high speed gliding Alarms and the three alarm levels are issued depending on the forecasted time to impact not a geometrical distance The first alarm level is usually issued 18 to 20 seconds the second one 13 to 15 seconds and the third one 8 to 10 seconds prior to the predicted impact and last as long as the alarm level is appropriate Depending on the impact forecast alarm levels might even go down or disappear Alarms are highly selective i e they are only issued when there is imminent danger In an additional information mode called nearest mode the user can be informed about other aircraft in the vicinity even when not posing any elevated danger Version 1 03 Page 13 of 17 April 1st 2006 INST
10. C application exists for this called FLARMTOOL A separate P C downloading program is supplied for updating the OZFLARM display software See software manual After switching on Depress UP the ON switch and the self test routine the unit must first capture satellite signals to establish position Even if the antenna has a clear sky view this process can take a few minutes The GPS LED will be red extinguishing when it has lock If it remains red for more than 2 minutes then check that the top surface is not covered by a metallic object RED LED will stop the FLARM from working Because the unit can take a minute or two to lock onto a GPS signal a glider tug pilot should leave OzFLARM switched on during brief waiting periods between flights During night flights OZFLARM must be switched off Only the Power Data socket to the unit may be used for updating FLARM software or obstruction data from the PC During this process OZFLARM must be disconnected from other equipment Version 1 03 Page 6 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT T Extension An 8 pole connector may be inserted in the 8 pole RJ45 socket on the right side looking from the rear The connections to the pins are the same as for Pins 1 and 8 described above This socket is intended for use by third party applications e g for glide computers requiring NMEA GPS output or other PDA displays Settings for the GPS speed and message type
11. IS B FIS B or ADS B The use of OzFLARM is at the sole responsibility and discretion of the aircraft commander or his delegated crewmember Operation must be preceded by full familiarisation with the equipment and careful study of the Operating Manual At present OzFLARM is not certified by the Civil Aviation Authorities and has not been tested in accordance with the normal aviation requirements e g DO 160E The FLARM software development s commensurate with Level E of DO 178B in other words a failure of the unit will have no effect upon aircraft operation and does not increase crew workload The OzFLARM obstruction data bank is not certified Air band radio frequency allocation and licensing conditions may vary from country to country The aircraft commander is solely responsible for ensuring that OZFLARM is operated in conformity with the respective licensing conditions No licence is required to operate OZFLARM in Australia Until further notice OZFLARM may not be used in the USA or Canada without written authority of FLARM Technology or in aircraft that is registered and or insured in the USA or Canada Likewise operation of FLARM is forbidden in aircraft in which one or more of the occupants resides in or is a citizen of the USA or Canada Likewise use of FLARM is forbidden if the aircraft concerned takes off from makes an intermediate or final landing in the USA or Canada HF Developments its associates development team suppliers m
12. al configuration information can be found in the Data Port Specifications document We always welcome suggestions for the improvement of OZFLARM The latest version of this handbook and other related documents can be found at the Website www rf developments com This Website also has answers to Frequently Asked Questions This Website also carries announcements when new software versions or functions are available If you enter your name on the mailing list you will automatically receive notification of changes as and when they happen support rf developments com Software Versions FLARM 2 x will only remain operational until the end of February 2006 On publication the update will have no functional changes and can be downloaded free of charge current update is version 3 xx valid till Feb 2008 Users will be able to load the software with the aid of a suitable power supply data cable not supplied This operation requires the user to have the unit serial number to hand Software validity has to be time limited to ensure that all FLARM units are mutually compatible and updates include the latest ground obstruction data 2 How it works Basically the OzFlarm unit consists of 2 core modules The first is the FLARM microprocessor This controller is identical to the SwissFlarm system being used in Europe The technology utilises the tried and proven Aircraft risk prediction Algorithims and obstacle database Additional to this OzFlarm a
13. anufacturers and data suppliers accept no responsibility for any damage or claims that may arise from use of OZFLARM Version 1 03 Page 11 of 17 April 1st 2006 12 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Technical Data The following data are provided without guarantee and may be altered at any time without notice Height Width Length Weight Power supply Power drain Serial data GPS Radio Temperature Intercom Vibration Country of Origin Version 1 03 25 mm housing without internal radio antenna 100 mm overall height with internal radio antenna 75mm 111 mm housing without cable connectors 119 mm overall length with push button without cable connectors 155 g with internal radio antenna without cable without GPS antenna external power supply 6 0 to 28 0 peak voltage up to30 0 VDC via RJ45 recommended value 12 VDC direct galvanic link to aircraft battery via an obligatory 500 mA circuit breaker separated from essential aircraft systems OzFLARM has a reverse polarity protection typically approx 55 mA at 12 VDC approx 37 mA at 24 VDC normal operation without warnings or external display a collision warning may double these values bi directional RS232 compatible with NMEA 0183 Version 2 0 standard message format GPRMC GPGGA data rate 4 8 to 57 6 kBaud additional NMEA proprietary sentences PFLA and PGRMZ described in a separate document 16 Chann
14. e appendix A A pressure sensor further enhances the accuracy of position measurements The predicted own flight path is calculated by the FLARM micro and the information transmitted by radio as a low power Requires Hardware Version 2 or higher However the vertical bearing on the serial data output is also available to third party equipment on Hardware Version 1 Version 1 03 Page 3 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT digital burst signal at one second intervals Provided they are within receiving range these signals are received by further aircraft also equipped with OzFLARM The incoming signal is compared with the flight path calculated and predicted for the other aircraft At the same time FLARM micro compares the predicted flight path with known data on ground obstructions including electric power lines radio masts and cable cars only if the obstacle database is loaded If FLARM determines the risk of dangerous proximity to one or more aircraft or ground obstructions the unit gives the pilot warning of the greatest danger at that moment The warning is given by a Dee Dah sound sound 2 tone high Low The relative direction LED rose will light depending on which direction a target is received Typically and green leds represent 1km or further away targets and are not deemed dangerous Red indicates targets within 1Km and flashing red indicates a potential threat The operating range is v
15. e aircraft technical logs as to reflect an installation performed under a no interference no hazard basis as is the case for glide computers and PDA displays as well as other GPS devices You as the installer must observe this rule Additional tests under a no interference basis might include the operation of the radio and a check that OzFlarm causes no interference to its normal operation Checks that other aircraft systems do not interfere with OZFLARM are also needed The best method is to fly with a friend at a distance around 2 kms make sure all systems are off i e other GPS vario and glide computer observe his lit target LED and maintain that distance Turn on each piece of equipment and note any change Acceptable operation is one that is not affected by other devices Should a problem occur then consult our FAQ page Version 1 03 Page 4 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT 4 Housing The lower face of the housing has two threads so that OZFLARM can easily be secured with two M5 screws no more than 10 mm long This thread is in widespread use in gliding and 2 screws are provided with each unit OZFLARM should be installed on a flat surface so that the housing is not subject to any mechanical stress Make sure the top area of the housing is not covered by any ferrous material as the internal GPS antenna is housed here If it has to be mounted lower in the panel or covered then use of the optional
16. e and this will work If you have trouble return to us with a return pre paid sachel and we will re install for free If you do not want to attempt this at all then return with pre paid sachel and we will do it at no labour charge Version 1 03 Page 10 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT 9 Radio Antenna The rear of the housing has an SMA connector onto which is screwed an 86 mm long internal 1 4 radio antenna The antenna must be fitted and removed with care This antenna is required for operation of OzFLARM and the correct installation has a considerable effect upon range for transmission and reception so the installation must be carefully considered The antenna must be vertical allowing generally unobstructed radiation to the front and sides It is theoretically possible to use an inverted installation but only when making exclusive use of an external display Horizontal or inclined installation is not acceptable In articular there should be no electrically conducting surfaces metal carbon fibre above or immediatel alongside the antenna The antenna must not be under stress or bent e g by the cockpit canopy RF Developments can supply alternative external dipole antennas with 1 0m and 2 5m feed cables for external installation and antenna extension cables 500 RG 174U on conventional SMA No antennae or cables may be used other than those listed above An external antenna must be adequately
17. el WAAS EGNOS compatible GPS engine external 502 active antenna with 2 5m RG 174U cable MCX connector 3 3V dimensions depending upon the antenna used usually rectangular 45x45 to 50x50 mm oval or circular of approx 12 mm thickness SRD Band 915 0 to 928 MHz Australia other frequencies depending upon configuration less than 1 Duty Cycle Peak Pulse Power 10 mW ERP internal 4 4 antenna screw fitted to conventional SMA connector Range approx 2 km possibly up to 5 km depending upon antenna and installation Operation 10 to 60 storage 20 to 70 TC no certification in accordance with DO 160E Sections 4 and 5 not provided suitable third party units are available Use in conditions of strong vibration or turbulence should be avoided or subsequently checked prior to continued operation no certification in accordance with DO 160E Section 8 Australia Page 12 of 17 DECLARATION OF CONFORMITY Complies with AS NZS 4268 2003 Low power transmitting and receiving device RF Developments N 15142 ABN 60 789 837 451 This device must be operated in accordance with the manufacturers recommended installation and users guide Under no circumstances should this equipment be modified Modifications will render the unit un approved and removes all warranties April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Appendix A OzFlarm Basics Volume Power 6 O S de moe an Mode c O
18. ems This might be necessary if the pilot suspects that FLARM may be interfering with another on board system the suspected presence of smoke the smell of smoke or flying in a country where the use of FLARM is not permitted In spite of the reverse polarity protection it is important to check for correct polarity during installation in articular the power supply and data wires must Connector with Pin numbers Open ended Patch Cable not be interchanged The transparent connector tab down allows for a visual check of the cable colour codes ensuring that the open end of the cable is correctly configured When using patch cables neighbouring wires on Pins Pin 1 2 3 4 5 6 and 7 8 are usually but not always twisted together Neighbouring wires usually have the same colour though one of the pair has a colour alternating with white In normal configuration Pin 5 transmits the most important NMEA 0183 Version 2 0 compatible GPGGA and GPRMC codes at a fixed data rate of 19 2KB NOTE under no circumstances must this speed be changed otherwise the display section and alarms will cease to work see document Data Port Specifications from Hardware version 2 also Garmin proprietary PGRMZ codes with barometric altitude information Further codes are provided for third party applications e g external displays These are described in a separate document Data Port Specifications This document also describes how FLARM may be configured A P
19. ery dependent upon the antenna installation in the aircraft The normal range is about 2 km but up to 5 km may be achieved in individual cases such as ground stations use of external high gain antennas see options on RF Developments website The GPS and aircraft situation coordinates of the other aircraft can also be made available for use in other systems e g external display speech synthesizer PDA via a serial data output There are a number of manufacturers for such equipment In addition OZFLARM operates as an IGC compatible flight data recorder if this software option has been configured logger is not IGC approved but fully functional including pressure height recording 3 General Advice on Installation Installation and operation must be on the basis of non interference with and no hazard to the existing suite of other certified equipment necessary for safe flying operation or installed to comply with official requirements Installation and operation must comply with official regulations and requirements When OzFLARM is permanently installed in an aircraft the installation must comply with the Installation Policy published by the Civil Aviation and Safety Authority CASA OzFLARM must be secured in such a position that the pilot has the display LEDs in direct view that he can hear the acoustic warning tone and operate the control buttons OZFLARM must not obstruct the piloting operation and in particular it must
20. external antennas will be required These can be purchased on the web site The housing can be repeatedly attached and released using the DualLock supplied with the unit The unit comes supplied with two self adhesive 12 5x25 mm fixtures Care should be taken to ensure that the bonding strength is very strong on both halves and difficult to detach The lower face of the housing also has two Phillips screws that hold the two halves of the housing together These screws must not be over tightened Avoid opening the case unless you need to i e select external GPS antenna option If you need to select the GPS antenna option please do not overtoghten the PCB to housing screws Should the unit become wet it should be thoroughly dried prior to use Should the unit be massively cooled condensation may occur The housing should only be cleaned with a slightly moist non abrasive cloth without any cleaning agents Scratches and abrasion can damage the housing The ABS polycarbonate plastic housing is black to minimise glare and has been tested at temperatures from 10 to 60 C Efforts should be made to prevent exposure to excessive direct or indirect solar heating Even if not subject to mechanical stress the housing may be deformed at temperatures upwards of 84 C and can also be deformed at lower temperatures in the presence of mechanical stress The unit should not be exposed to strong locally focused sun radiation therefore care should be taken
21. lso uses the standard Flarm datalogger feature Software updates are performed via the Flarm port which has identical connections to the Swiss Flarm unit The second module is the OzFLARM interface This micro handles the OzFlarm compass display and beep alert Additional to display functions it has a future upgrade path when coupled to a suitable ADS B receiver to start receiving and displaying ADS B targets OzFlarms micro also looks after the housekeeping power management etc Updates to OzFlarm are performed via the OzFlarm dataport The same download cable can be used as in the Flarm port both are pin identical Additional to providing access to the micro we also have an NMEA port available for connection to a moving map display or other glide computers or PDA s Note This system is by default 100 percent compatible with FLARM from Europe Europe and Australia operate on a different frequency contact FLARM if you require changing to the Australian channels if you already have a Swiss Flarm unit OZFLARM units going overseas in gliders for competitions we can re program your units to suit Note that due to the different frequency span both systems will be degraded slightly due to matching however they will still achieve a satisfactory result OzFLARM receives position and movement information from an internal 16 channel GPS receiver with an internal antenna external can be connected by selecting the appropriate antenna switch configuration se
22. not hinder his field of view These requirements must be maintained at all times during conditions of strong turbulence and acceleration OzFLARM is not suited for use in conjunction with night vision systems night flying no dimmers or in pressurised cabins Ideally OzFLARM will be installed under the instrument panel on the central console or on the cockpit sidewall The rear face of OZFLARM must face in the direction of flight If OZFLARM is also equipped with an external display and operating unit then it may be installed elsewhere and another orientation Usually such an installation requires an external radio and GPS antenna It is usually best to install OZFLARM in such a position that the Power Data socket are easily reached from a PC with an extension cable This simplifies downloading the latest ground obstruction data and software and configuring the unit When updating software the user must know the unique OzFLARM unit serial number If possible OZFLARM should be so installed that the pilot does not inadvertently touch the push button during cockpit ingress and egress Cables must not be folded or be under tension The installation must allow adequate space for cable connectors and the external vertical antenna OzFLARM the external radio antenna and the GPS antenna optional should each be installed at least 10 cm away from the magnetic compass more if possible After installation an appropriate entry should be made in th
23. p switch near the antenna connector The top and middle switch will be ON the bottom OFF Switch the top 1 and 2 to the OFF position hard left and the bottom switch ON The external GPS antenna is now selected Relocate PCB and insert screws DO NOT over tighten a light tension is all that is needed Version 1 03 Page 7 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT Picture Both halves open ready to undo top 5 screws t0 4 api R0 co oo Picture Default internal GPS antenna selected Version 1 03 Page 8 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT j an Na 795 at eek f IN T Ce fb A P m bf PW a emp oR L d1 WII TIL 49 000081 0 000 Picture external GPS antenna selected This completes the external GPS selection Plug in a suitable antenna into the GPS socket on the rear Antennas can be purchased from RF Developments The cable length of the 50 RG 174U cable with MCX connector is about 2 5 m cables of other length are not available from RF Developments A specialist must undertake any shortening of the cable which must not be cut to less than 0 5 m The external GPS antenna should be horizontal in straight flight and have an unobstructed sky view also during turns The antenna should not have any electrically conducting surfaces e g metal carbon fibre above or immediately alongside Ideall
24. y the antenna will be located on top of the instrument panel Electrically conducting sheet metal under the antenna may enhance its performance The antenna base contains magnets but nevertheless requires additional attachments The antenna must under no circumstances interfere with correct compass operation If the antenna interferes with the compass the magnets in the antenna base must be removed with a screwdriver and the metallic foil reattached If the aircraft is fitted with two or more GPS antennae they should be separated if possible by at least 25 cm the same holds good for FLARM radio antennae Hardware version 2 serial numbers 201 to xxx current Remove the 2 housing screws that secure the top lid to the main box you may have to lightly manoeuvre the lid out to clear the rear plastic lenses Locate the 3 position dip switch on the main PCB This has 3 slide switches with the defaults being 3 ON 2 ON 1 OFF To select external GPS then it should be 3 OFF 2 ON 1 OFF To re assemble extreme care must be used The top lid GPS section has 10 pins sitting beneath it for insertion into the main PCB Carefully line these up and at the same time check that the plastic front and rear Version 1 03 Page 9 of 17 April 1st 2006 INSTALLATION MANUAL OzFLARM COLLISION WARNING UNIT lenses are going to line up as well you maybe need to slightly open one side to see inside that the pins connect Some car
Download Pdf Manuals
Related Search