User's Manual
Contents
1. Serial Pon 1 Serial PRIMARY PR2200ELCDRTXL2U Gaal c ooge E a WalPor SerialPort l1 ARY 5 Battery Backup Surge Protected and AVR protected Outlets This unit provides a total of ten outlets with battery backup and surge protection They ensure that connected equipment will keep an uninterrupted operation over a period of time during a power failure Critical Non critical It is possible to program the unit in a way so that the outle block marked as non Critical 6 ports will stop the provision of power to connected equipment after a certain period of time thus making more runtime available for the equipment connected on the outlets marked as Critical 4 ports In other words the user can establish runtime priority for certain connected equipment maximizing its availability during a prolonged power outage This type of control takes place with the use of the provided PowerPanel Business Edition S W 6 AC In2. Items Unit Delay Time Min Battery Pack Numbers A Voltage Mode 220 230 240 V Static Frequency Tolerance 96 Slew Rate Hz Low Battery Shutdown Voltage V Firmware Version None Step 3 Press and hold the display toggle for 4 seconds When the icons blink the value of each item is changed by slightly pressing the toggle Step 4 To save the value and return to general mode press and hold the toggle for 4 seconds Note If the UPS is left idle for over 30 seconds during setup it will turn off the backlight and return to general mode automatically Note If the user does not want to save the new settings and return to the general mode there are two methods 1 Wait for the backlight to turn off or 2 By pressing and holding the Display toggle key for 10 second GreenPower UPS CyberPower s GreenPower UPS Circuit Design is a solution to this problem Power Loss When the Utility Power is operating normally Green Power UPS works in Bypass Mode Our GreenPower UPS design conducts power only through the Relay and still provides normal output voltage Bypassing the transformer reduces power consumption thereby conserving energy and saving money When the utility power is abnormal the UPS will operate under Battery or AVR Mode Under this condition Green Power UPS and a ENERGYSAVING traditional UPS would operate about the same UNA Eque trial i On average utility powe
3. PowerPanel Business Edition S W provided The UPS can control the computer s shutdown in case of an emergency and at the same time the computer can monitor the UPS and alter its various programmable parameters On the other hand secondary Serial Port II only allows the UPS to initiate the connected computer s graceful auto shutdown in case of an emergency 10 EPO Emergency Power Off Port Use the provided gray cable to connect to a special EPO contact switch Follow the appropriate circuit diagram below to wire the cable to your EPO configuration The EPO remote switch is a switch installed in an outside area connected to the unit via an ordinary RJ 11 phone line In case of an emergency it can be used to immediately cut off power from the UPS unit BASIC OPERATION DD 2 v QberPaven FRONT REAR PANEL DESCRIPTION 1 Power Switch Master on off switch for equipment connected to the UPS 2 Power On Indicator Indicate that the AC utility input power s condition is normal and that the UPS outlets are providing power free of surges and spikes 3 Multifunction LCD Readout An LCD that shows various UPS information using icons and messages 4 LCD Readout Toggle Button Used to select among a variety of information the LCD can display BASIC OPERATION continued PR1000ELCDRTXL2U PR1500ELCDRTXL2U 3 13 9 14
4. CyberPower Reliability Quality Value User s Manual Professional Rack Mount LCD XL Series PR1000ELCDRTXL2U PR1500ELCDRTXL2U PR2200ELCDRTXL2U K01 0000144 01 IMPORTANT SAFETY INSTRUCTIONS This manual contains important instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate the UPS CAUTION The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection DO NOT plug the UPS into an outlet that is not grounded If you need to power drain this equipment turn off and unplug the unit CAUTION The battery can power hazardous components inside the unit even when the AC input power is disconnected CAUTION The UPS should be near the connected equipment and easily accessible CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION To reduce the risk of an electric shock do not remove the cover except to service the battery There are no user serviceable parts inside except for the battery CAUTION To avoid electrical shock turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer component CAUTION To reduce the risk of fire connec
5. K The likelihood of such a shock will be greatly reduced if such grounding is removed during installation and maintenance GU ON BATTERY REPLACEMEN continued BATTERY REPLACMENT PROCEDURE 1 Remove the front panel on the 2 Remove the two retaining screws right side of the cable protection cover then remove the cover 3 Remove the one retaining 4 Disconnect the black wire and red screws of the cable connectors wire from the battery 5 Remove the three retaining 6 Put the new battery packs back into the Screws compartment Tighten up the screws and replace the cable protection cover and the front panel Recharge the unit for 8 hours to ensure the UPS performs expected runtime REMINDER The used batteries are hazardous wastes and must be disposed through recycling Most retailers that sell lead acid batteries collect used batteries for recycling as required by the local regulations 10 11 DEFINITION FOR ILLUMINATED LCD INDICATORS Input voltage meter This meter measures the AC voltage from the wall outlet The INPUT voltage readout is used to identify the input voltage information This can be used as a diagnostic tool to identify poor quality input power Units are listed in V Volts When the UPS connect to any equipment the AVR can provide a stable 220 230 240V power output In the event of a complete loss of power severe brownout or over voltage the UPS relies on its internal battery to back up t
6. NTILATION OPENINGS AROUND THE HOUSING DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS INSTALLING YOUR UPS SYSTEM UNPACKING The box should contain the following 1 UPS unit x 1 2 User manual x 1 3 Phone line x 1 4 PowerPanel Business Edition software CD x 1 5 USB A B type cable x 1 6 Rack mount Brackets x 2 7 Skids x 2 8 Emergency Power Off Cable gray x 1 9 Serial Interface Cable DB 9 x 2 10 Power cord x 5 AUTOMATIC VOLTAGE REGULATOR AVHR The PR1000ELCDRTXL2U PR1500ELCDRTXL2U PR2200ELCDRTXL2U can stabiliz the consistent utility power The utility power may be damaging to What is AVR important data and hardware but Automatic Voltage Regulation helps the atic Voltage Re computer not experience dangerous voltage levels Automatic Voltage Regulator automatically regulates low or high voltages to keep equipment working at safe AC power levels 220 230 240V without switching to battery Your equipment can operate normally even meet the power problems such as shout brownouts and blackouts The unit s powerful sealed lead acid batteries will provide power only if the incoming voltage drops below 150V or increases above 300V INSTALLING YOUR UPS SYSTEM continued SYSTEM BLOCK DIAGRAM EMI Surge Output Charger AC DC Normal Mode LSS annn Battery Mode a Input HARDWARE INSTALLATION GUIDE 1 Battery charge loss may occur during shipping a
7. elephone fax machine or network device INSTALLING YOUR UPS SYSTEM continued 5 Press the power switch to turn the UPS on The Power On indicator light will illuminate If an overload is detected an audible alarm will sound and the UPS will emit one long beep In order to reset it turn the unit off and unplug some equipment from outlets Make sure your equipment carry a load current within the unit s safe range refer to the technical specifications and then turn the unit on 6 Your UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will be automatically charging even when the unit is switched off 7 To always maintain an optimal battery charge leave the UPS plugged into an AC outlet at all times 8 Before storing the UPS for an extended period of time turn the unit OFF Then cover it and store it with the batteries fully charged Recharge the batteries every three months or so to ensure good battery capacity and long battery life further this might also prevent damage to the unit from an unlikely battery leakage 9 The unit provides one Primary Serial Port I Secondary Serial Port Il and one USB port paired with the Primary Serial Port to allow connection and communication between the unit and any attached computers The Primary Serial Port I as well as its paired USB port allow for bi directional communication among the UPS and the primary connected computer running the
8. is automatically regulating low or high AC input line voltage conditions without resulting to the use of battery power Silent mode icon This icon appearing indicates that the buzzer will not be beeping while in battery operating mode During Silent mode the unit s alarm does not sound until the Battery Capacity falls to 20 Over load icon This icon will appear followed by an alarm indicating that an overload condition has been reached To recover from the overload condition start unplugging your equipment from the UPS outlets until the icon disappears and the alarm stops Fault icon When activated indicates a system fault error Please refer to the troubleshooting table for possible causes and solutions BATT CAPACITY BATT CAPACITY is shown as a bar chart each segment indicates approximately a 20 of battery capacity LOAD CAPACITY Load CAPACITY is shown as a bar chart each segment indicates approximately a 20 of load capacity LCD SETUP FUCTIONS 1 General Mode a Press the Display Toggle button to check the status of the UPS status Item Unit 1 Input Voltage V 2 Output Voltage V 3 Output Frequency Hz 4 Load Kw 5 Estimate Run Time Min 6 Load Capacity 96 7 Battery Capacity 96 8 Centigrade C 9 Fahrenheit F b Press and hold the Display Toggle button for 4 seconds If the machine is in the Battery Mode with active alarm it will become silent If the machi
9. k Connector Provides a connection for additional CyberPower external battery packs for extended runtime BATTERY REPLACEMENT Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the batteries Servicing the batteries should only be performed by professionals Please Contact your dealer or email to service cyberpower eu com Make a note for the replacement battery pack number RBP852 regarding PR1000ELCDRTXL2U PR1500ELCDRTXL2U and PR2200ELCDRTXL2U models CAUTION Use only the specified type of battery HR9 12FR for PR1000ELCDRTXL2U PR1500ELCDRTXL2U and PR2200ELCDRTXL2U Contact your dealer for replacement batteries CAUTION The battery may present the risk of electrical shock Do not dispose of batteries on fire since they may explode Follow all local ordinances regarding the proper disposal of batteries CAUTION Do not open or mutilate the batteries Released electrolyte is harmful to the skin and eyes and may be toxic CAUTION A battery can present a high risk of short circuits and electrical shocks Take the following precautions before replacing the battery Remove all watches rings or other metal objects from your hands Only use tools with insulated handles DO NOT lay tools or other metal parts on top of battery or any battery terminals Wear rubber gloves and shoes Determine if the battery is grounded If so remove source of ground CAUTION CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOC
10. let Connect the AC Power cord to a properly wired and grounded outlet 7 Output Circuit Breaker The circuit breaker serves to provide output overload and fault protection 8 Input Circuit Breaker The circuit breaker serves to provide input overload and fault protection 9 USB port to PC This is a connectivity port allowing communication and control among the UPS and the connected computer You should install on your computer the PowerPanel Business Edition software appropriate to the operating system you are using 10 Surge Protected Communication Ports RJ11 RJ45 These ports are being used to protect from various surge conditions the standard RJ 45 RJ 11 based ADSL LAN Phone Modem Lines cabling systems 11 Serial Port I Primary Serial port allow for bi directional communication among the UPS and the computer The UPS can control the computer s shutdown in case of an emergency and at the same time the computer can monitor the UPS and alter its various programmable parameters BASIC OPERATION continued 12 Serial Port Il Secondary Serial Port allows the UPS to initiate the connected computer s graceful auto shutdown in case of an emergency 13 SNMP HTTP Network slot Remove the cover panel to install optional SNMP allowing your UPS be controlled and monitored via a network connection 14 EPO Emergency Power Off Port Allow for an emergency UPS Power Off from a remote location 15 External Battery Pac
11. nd storage For the first time the UPS is used it s strongly recommended to charge batteries for at least eight hours is recommended to ensure that the batteries maximum charge capacity To recharge the batteries simply make the UPS plugs into an AC outlet 2 When you use the included software connect either the serial or the USB cable between the computer and the corresponding port on the UPS Note If the USB port is used the serial port will be disabled They cannot be used simultaneously The computer with the PowerPanel Business Edition S W connects to the USB port or the Serial port on the UPS It can control the operating schedule battery test outlet etc and get information on the UPS status However other computers with PowerPanel Business Edition S W can only get UPS status information via a LAN connection 3 With the UPS off and unplugged connect your computer monitor and any externally powered data storage device Hard drive Tape drive etc into the outlets DO NOT plug a laser printer copier space heater vacuum paper shredder or other large electrical device into the UPS The power demands of these devices will overload and possibly damage the unit 4 To protect a fax telephone modem line or network cable connect the telephone or network cable from the wall jack outlet to the jack marked IN of the UPS Then connect a telephone cable or network cable from the jack marked OUT on the UPS to the modem computer t
12. ne is in the Line Mode a self diagnostic test will take place c If the Display Toggle button remains untouched for over 30 seconds the LCD backlight will turn off automatically 2 Set up Mode Step 1 Hold the Display Toggle button for 10 seconds to enter the UPS Set Up Mode Step 2 By pressing the Display toggle users can switch between setup functions Some User Configurable functions are as follows a Delay Time The time delay between switching from Battery Mode to Line Mode There are 9 different settings The default setting is 0 minutes Battery Pack Numbers This function provides the estimated UPS runtime using various numbers of battery packs The default setting is 0 Static Frequency Tolerance There are 4 settings 1 2 4 6 and the default setting is 6 Functional description The setting may be adjusted to the quality of the electricity in use Slew rate Also known as Dynamic Frequency Tolerance There are 5 different settings 0 25 0 5 1 2 4 Hz Sec The fault value is 4Hz sec Functional Description Slew Rate indicates the tolerance of a device in accepting frequency variance Lower Slew Rate results in less tolerance but better protection for the connected load and vice versa Low Battery Shutdown Voltage This function will adjust the UPS shutdown point according to the battery s remaining capacity These programmable items are sorted by unit as in the following table
13. nected to an AC outlet The unit must be connected to a 220 230 240v outlet The batteries have degraded Contact CyberPower Systems about replacement batteries at service cpsww com au Mechanical problem Contact CyberPower Systems at service cpsww com au PowerPanel Personal Edition is inactive The serial cable or USB cable is not connected Connect the cable to the UPS unit You must use the cable that came with the unit The cable is connected to the wrong port Try another port of your computer The unit is not providing power of batteries Shutdown your computer and turn the UPS off Wait 10 seconds and turn the UPS back on This should reset the unit The serial cable is not the cable that was provided with the unit You must use the cable included with the unit for the Software For more information visit www cpsww com au or contact CyberPower Systems Australia E MAIL service cpsww com au Ce Pb Free A _ P X f h E F N N F y 11
14. o supply a consistent 220 230 240V output Output voltage meter The Output Voltage screen measures in real time the AC voltage that the UPS is providing to your connected equipment via the UPS outlets Units are listed in V Volts Estimate run time The Estimated Runtime Screen displays how many minutes of runtime can be expected of the UPS if it were to experience a power outage When runtime becomes shorted the battery capacity will decrease battery capacity bar indicator will be falling Note The number displayed may be less than actual runtimes for low loads LOAD The LCD displays detailed i the UPS status and current power conditions to alert you to potential power iproblems before the affect your i equipment Note All related UPS i information is based on that you should i turn on the UPS d Normal icon This icon illuminates when the UPS is working under normal conditions Battery icon When there is a severe brownout or blackout this icon will appear followed by an alarm two short beeps indicating that the UPS is now working using its internal batteries Once the batteries are run out of power over a period of time a constant alarm will sound If this happens and main power has not been restored it is recommended that you save your files and turn off your equipment manually as soon as possible Automatic Voltage Regulation AVR icon This icon will appear when the unit
15. r operates 88 of the time and the CyberPower GreenPower Technology will work in its money energy saving Bypass Mode TECHNICAL SPECIFICATIONS Model PR1000ELCDRTXL2U PR1500ELCDRTXL2U PR2200ELCDRTXL2U Capacity VA 1000 1500 2200 Capacity Watts 750 1125 1650 Input Input connections IEC 320 C14 IEC 320 C20 Nominal Input Voltage 220 Vac 240Vac Input Voltage Range 160Vac 290Vac Input Frequency Range 50 60Hz 3Hz Auto Sensing Output On Battery Output 240Vac 5 Voltage On Battery Output 50 60Hz 0 1Hz Frequency Transfer Time Typical 4ms Overload Protection On Utility Circuit Breaker On Battery Internal Current Limiting tering Surge Protection and Fil Lightning Surge Protection Yes Internet Ready DSL Phone FAX Modem Protection RJ11 RJ45 One In One Out Physical Output Receptacles 10 IEC C13 9 IEC C13 1 IEC C19 Dimensions cm 2U Rack 43 3 x 8 8 x 48 Weight kg 33 9 35 31 3 Battery Sealed Maintenance Free Lead Acid Battery 12V 9 0AH x4 Hot Swappable External Battery Yes Warning Diagnostics Indicators Power On LCD Display Using Battery AVR Load Level Battery Level Audible Alarms On Battery Low Battery Overload Environmental Operating Temperature 32 F to 104 F 0 C to 40 C Operating Relative H
16. t the UPS to a circuit with 16 amperes maximum over current protection in accordance to CE requirement CAUTION The AC outlet where the UPS is connected should be close to the unit and easily accessible CAUTION Please use only VDE tested CE marked mains cable e g the mains cable of your equipment to connect the UPS to the AC outlet CAUTION Please use only VDE tested CE marked power cables to connect any equipment to the UPS CAUTION When installing the equipment ensure that the sum of the leakage current of the UPS and the connected equipment does not exceed 3 5mA CAUTION This is permanently connected equipment and only qualified maintenance personnel may carry out installations CAUTION Do not unplug the unit from AC Power during operation as this will invalidate the protective ground insulation CAUTION DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT Under no circumstances this unit should be used for medical applications involving life support equipment and or patient care CAUTION DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire do not use with or near aquariums Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out CAUTION DO NOT USE WITH LASER PRINTERS The power demands of laser printers are too large for a UPS DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE DO NOT BLOCK OFF VE
17. umidity 0 to 95 Non Condensing Communication PowerPanel Business Edition Software Windows 98 ME NT 2000 XP Vista Windows 7 Management Self Test Manual Self Test Auto Charger Auto Restart Yes COM Interface True RS232 x 1 Contact Closure x 1 Built in USB interface Yes SNMP HTTP 1 Networking Optional TROUBLE SHOOTING Problem Possible Cause Solution Outlet does not provide power to equipment Circuit breaker has tripped due to an overload Turn the UPS off and unplug at least one piece of equipment Wait 10 seconds reset the circuit breaker and then turn the UPS on Batteries are discharged Recharge the unit for at least 4 hours Unit has been damaged by a surge or spike Contact CyberPower Systems about replacement batteries at service cpsww com au Uncritical outlets have turned off automatically due to an overload Push the toggle button to make the uncritical outlets turn on The UPS does not perform expected runtime Batteries are not fully charged Recharge the batteries by leaving the UPS plugged in Batteries are degraded Contact CyberPower Systems about replacement batteries at service cpsww com au The UPS will not turn on The on off switch is designed to prevent damage by rapidly turning it off and on Turn the UPS off Wait 10 seconds and then turn the UPS on The unit is not con
Download Pdf Manuals
Related Search