Photocell beam sensor User Manual (P5101 V10)
Contents
1. external alarm 4 5 3 Power on after correct connection You will find LED will turn on when you make alignment at the emitter and receiver or led will off Photocell switch PHOTO works in set up status NO or NC see 4 3 If there s obstacle between the transmit and receive module Buzzer will beep J3 at Celled PHOTO switch OFF or ON When J5 is keep NC alignment the emitter and receiver LED will be on photocell switch is ON if someone or something shelter the sensor the Led will turn off photocell switch is OFF V Installation Pictures 1 Open package 2 Fix the holder 3 Drill and fix Connect and take out location map on expansion accessories wall sleeve 6 Put 7 Screw bottom and top 8 Finished cover on cover together2. Al Photocell beam sensor User Manual P5101 V10 I Technical Specification Working voltage 12 24VAC DC or 2 1 5VGNISA Battery Working current 24VDC emitter lt 8mA receiver lt 40mA Photocell wavelength 940nm Angle of opposite emission lt 5 Receiver range gt 12m Internal Rotation system adjusted Angle 0 180 Working temperature 20 60 C Relay contact loading capacity 1A 30VDC Size 127 50 28mm ll Safety Instruction 1 For security please read the user manual carefully before initial operation 2 This photocell is without any fuse so Please make sure the power is off before installation 3 Only used this system that do not cause any danger life or property during the running failure or its security risks eliminated 4 Please guarantee the products used in effective working range lll Picture Display Emitter Receiver si Lar J5 N A lt x A x P nc m m as ra ra ra ra ra N N EN N EN SAO ASS SS 12 24V NC 12 24v PHOTO LOW BAT ac pc EDEG AC DC J2 r T Jo ieee E D No Ti z fale NC fr 3 a Z4 ai tes laa 7 12 24V NC Ac pc EDES 12 24V 12 24VAC DC PHOTO LOW BAT AC DC IN Al IV Installation instruction 4 1 Youcan choose external power supply 12 24V AC DC or Battery supply J2 in transmit module 4 1 1 put the short circuit cap on Ext Power Supply voltage 12 24V AC DC 4 1 2 put the short circuit cap on BAT
3. TERY Battery voltage 3V 4 2 You can set the buzzer working or not by switch J3 4 2 1 Buzzer works when short circuit cap on celled 4 2 2 Buzzer not work when short circuit cap on No celled 4 3 You can set the switch of photocell NO and NC by jumper J5 4 3 1 when the short circuit cap on NO The photocell will be Normal Open 4 3 2when the short circuit cap on NC the photocell will be normal closed 4 4 Installation 4 4 1 The photocells should be installed more than 20cm above the ground to avoid reflection and the distance between emitter and receiver shall be more than 50cm End user should install the photocell on the back of the direct sunlight or other strong light source 52 to keep photocell work well steadily 4 4 2 Avoid installing other infrared photocell emitters within the effective distance of receiver 4 4 3 Ifthe end user need to install other photocells in one same straight line the receivers could be installed in the two ends and the emitters could be back to back installed 4 4 4 Stable installation could avoid the signal of emitter and receiver skewing due to lightly vibrate and the malfunction 4 5 Wire connection 4 5 1 You can choose safety switch for transmit module If not it should be short circuit by the cap PLS see PIC 6 4 5 2 PHOTO is the switch contact and can select NO or NC LOW BAT is the low voltage alarm switch to buzzer when working voltage of emitter module is lower than 2V Also it can activate the
Download Pdf Manuals
Related Search