iZone 220 & 320 Rev 1 installaion and user manual.pub
Contents
1. izone Installation Configuration amp User Manual for iZone 220 amp iZone 320 Table of contents Section ee Se Se ee ee Se ee I ee 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 10 11 12 13 14 15 16 17 18 19 Description Installation iZone 220 Wiring layout for base system up to 8 zones iZone 220 Wiring layout for base system up to 9 to 14 zones Stand alone VAV system for a typical 4 zone system iZone 320 Wiring layout for base system up to 8 zones iZone 320 Wiring layout for base system up to 9 to 14 zones Optional equipment for wireless temperature controlled zones Optional equipment for wired temperature sensors Optional equipment for iSense temperature and occupancy controlled zones Optional equipment for colour touch screen temperature controlled zones Example of different types of temperature sensors and controllers on a single system Option equipment for wired WiFi control of system Option equipment for wireless WiFi control of system iZone 320 Optional equipment for iSave addition up to 6 zones iZone 320 Optional equipment for iSave addition 7 to 12 zones iZone 320 Optional equipment for Ethernet Home Automation connection iZone 320 Wiring connection to AC units iZone 320 Wiring connection to LG units iZone 320 Wiring connection to Temperzone units General installation instructions Table of contents Section Description Page No 2 02. Monday 8Jun 2015 3 50 PM WiFi Configuration O IP Address Select either Auto or Manual Configuration If manual is selected you will need to know the IP Subnet Mask Default Gateway Primary DNS Server and Secondary DNS Server addresses if applicable IP Address Subnet Mask Default Gateway Primary DNS Server Secondary DNS Server Touch here to apply the changes to the A i ee fi configuration Apply Previ ous 4 Back iZone Inventive Intelligent Intuitive Touch here to go to the home screen Touch here to go back without saving the changes 41 3 5 2 WIFI connection Monday 8Jun 2015 J 6 OE system Is Off AC Unit Zone Contra al Zone Alflaw Favourites Sleep Timer schedule set ime screen settings NN A grey symbol indicates the Bridge is connected to the iZone system but is not iz EEr a connected to the local A green symbol indicates the iZone d 2 af computer network system is now connected to WiFi and ready to use Beep system Cantig ione Inventive Intelligent Intuitive 42 3 5 3 Smart Phone Tablet or PC configuration System Requirements Smartphone Tablet or PC You will need a smartphone or tablet or PC The following platforms are supported Apple Android and Windows System Requirements IOS SOFTWARE REQUIREMENTS e Compatible with iPhone iPod touch and iPad iOS 6 0 and higher ANDROID SOFTWARE REQUIREMENTS Requires Android 2 1
3. Some functions may have been locked by your installer to ensure the commissioned values are not changed To make changes to these values contact your installation company Press to configure system 3 0 Press to activate or deactivate this screens audio feed back beep on touch Installing company s tag line will vary depending on the installation company Monday 8Jun 2015 Zone Control j Zone Airflow Set Time Fota System Config OA iZone nventive Intelligent Intuitive System date and time Press to activate a favourite mode or to configure a new favourite 4 9 Press to activate a schedule or to configure a new schedule 4 11 Press to change screen settings 4 14 Press to get more help about your iZone system A C system maintenance required Press here for instructions WiFi connection 47 4 2 iZone 320 home screen To get back to the Home screen at any time press e When entering names or values using the keyboard it is easier to use a thin object such as a toothpick Do not use sharp hard objects as they may damage the screen The enter button must always be pressed to save the changes you have made Some functions may have been locked by your installer to ensure the commissioned values are not changed To make changes to these values contact your installation company Press to turn your system on or off Press to chang
4. C320L 22 1 18 iZone 320 Wiring connection to Temperzone units Unit Make Connection Temperzone 1 Connect a shielded 2 core twisted pair control cable from the C220 to the UC7 board in the condensing unit This cable is supplied by the installer Polarity is critical see Fig A amp B for correct connection Adjust location of jumper J1 to suit the length of control cable installed 3 Ensure the dip switches in the condensing unit are set correctly for the installed compressor type digital fixed speed and fan speed control Refer to the Temperzone service manual 4 Fita link as shown in the Temperzone wiring diagram to enable BMS control This link is between the following terminal HOT24V AC and COMP 24V Hi OE N Tf Shielded 2 core twisted pair Me LI p TAL To e To tl A E control cable not supplied LE Seber bee i aa Ue k J shield _ as si ee ul is Ver 2 m Arg TE CIRIE rem Tia at UX EXU EXU a pi oo y Ph igs ca ES E y ai See note 4 si gen So nuu RR g Adjust jumper J1 to suit cable E be delli ta PE F ah di length 8 li l im E ul i Position of jumper J1 it od ee PLE E _________ sE nt sa F a5 UA a E leg Le For wire length 7 Poue z hae e hag 1 02 9 E ns Es oe par ETY ri he g longer tha
5. Install Sensor Module to allow for Wired temperature sensors CS Connect Sensor module to any network port in the system iZone Net port CCTS Install additional colour touch screens in zones requiring temperature control Max 12 CNEM Install Network Extension Module to provide additional network ports if required CZCO iSense Wired Zone Controllers with temperature and occupancy sensor Max 12 per system CDTS Installed into the supply air duct off the fan coil unit Must be installed on all zone temperature controlled systems Power supply Zone motors and CEXT not shown for clarity 15 1 11 Optional equipment for wired WiFi Control of system izone Pesta the iZone p to your smart amp App Store phone or tablet or PC ANDROID APP ON P gt Google play z N a Download from LE Windows Store iZone desk top PC App available from the iZone website CGB2C35 This special cable is specific for connecting the CCPU and Wired Bridge Power supply Zone motors and CEXT not shown for clarity Customers router or modem CB Wired Bridge Ethernet 16 1 12 Optional equipment for wireless WiFi control of system Customers x router or Z modem ATA izone oo CR optional Wireless Repeaters i FONDI the iZone IIC p to your smart App store phone or tablet or PC ANDROID APP ON P gt
6. Master AC unit control Indicates the current temperature of the air inside the air conditioning A Vil 5 cur l Next T SETS Bac ION Scroll up or down to see more zones iZone n Inventive Intelligent Intuitive 52 4 7 Zone airflow summary Monday 8Jun 2015 3 50 PM 8 Zone Airflow Indicates current minimum air flow setting to this zone Lone Zone name Indicates current maximum air flow setting to this zone Dining room Kitchen Press here to change the zone air flow settings Master bedroom John bedroom Hall DICI EE iZone ni Inventive Intelligent Intuitive Scroll up or down to see more zones 53 4 8 Changing zone airflows Please note It is possible to lock the maximum and minimum Monday 8Jun 2015 airflow settings in the configuration menus If you screen does not display as indicated here and you require to make changes to airflows please contact your installer to activate your display Living Room Indicates the current maximum airflow setting for this zone Indicates the current minimum airflow setting for this zone This is usually set at 0 Min Airflow will not display if this adjustment has been locked Scroll up or down to see more zones Previous IZone n Inventive Intelligent Intuitive Indicates current zone that you are changing the airflow to Press here to increase the maximum airflow to this z
7. Max 12 per all zone temperature controlled systems A Power supply Zone motors and CEXT not shown for clarity 12 1 8 Optional equipment for isense temperature and occupancy controlled zones CZCO iSense optional CNEM optional uo fono Install Network aih rollers Extension Module to tenerai provide additional network ports if required and occupancy sensor Max 12 per system CDTS Installed into the supply air duct off the fan coil unit Must be installed on all zone temperature controlled systems Power supply Zone motors and CEXT not shown for clarity 13 1 9 Optional equipment for colour touch screen temperature controlled zones CCTS Colour touch screen CNEM optional Install Network Extension Module to provide additional network ports if required CDTS Installed into the supply air duct off the fan coil unit Must be installed on all zone temperature controlled systems CCTS Colour touch screen Power supply Zone motors and CEXT not shown for clarity Settings 12 30 AMI ne no Zones amp s Shop Timer in ri 303 14 1 10 Example of different types of temperature sensors amp controllers on a single system CRFS Wireless Temperature F Sensors Max 14 per system CS Wired Temperature Sensors Max 12 per system CR Wireless repeaters To extend wireless range CSM
8. Mg Back iZone Inventive Intelligent Intuitive Touch here to enable Fan Auto control and to proceed with Fan Auto set up Touch here to set the AC Unit capacity for this system The capacity selection will provide an approximate airflow capacity for the AC Unit Touch here to fine tune the airflow capacity You can set the exact airflow in litres per second This is available from the AC Unit manufacturer 36 3 3 2 Fan auto zone area setup izone 320 only Monday 8Jun 2015 3 50 PM Fan Auto Config Touch here to set the kitchen area in Zone 1 Area sqm square meters J Zone 2 Area sqm Zone name Zone 3 Area sqm Current area set for Zone 3 Touch here to go to the next 3 zones ____ Next Pre HOUS as Ha ck SALI VW LI Pa iZone n Inventive Intelligent Intuitive 37 3 4 System Options Display Taglines amp Filter Mainenance Monday 8Jun 2015 3 50 PM 4 System Options Note Information on the configuration screen may vary depending which devices are connected to the system and if it is an iZone 320 or 220 Touch here to go back to the next page of options Display Tag Lines Filter Maintenance Next Ri Back iZone Inventive Intelligent Intuitive Select either Full System or Zone Only Select if you want the AC units controlling temperature to be displayed Touch here to change line 1 of the tag line Touch here to change line 2 of the tag l
9. P2 control wire from the fan coil unit and connect it to the iZone C220 Do not connect the 12V wire to the iZone Usually Red Connect the black and white wires from the fan coil unit to iZone C220 See detailed instructions on 1 17 page 22 Take the Remote Controller A B control wire from the fan coil unit and connect it to the AC Unit Control Cable on the C220 C320M Panasonic Take the A B control wire from the fan coil unit and connect it to the AC Unit Control Cable on the C220 C320P see detailed instructions on 1 18 page 23 Toshiba Take the A B control wire from the fan coll unit and connect it to the AC Unit Control Cable on the C220 C320T 21 1 17 iZone 320 Wiring connection to LG units Unit Make Connection LG 1 Connect a shielded 2 core twisted pair control cable from the C220 C320L to the P1485 Gateway M board in the condensing unit This cable is supplied by the installer Polarity LG condensing unit must be supplied with an ban is critical see Fig C amp D for correct connection optional PI485 Gateway M board in the condensing unit LG dipswitch settings are as follows Dip switches 1 and 4 ON gt All others are OFF Shielded 2 core twisted pair control cable not supplied B _ A Correct polarity Shielded 2 core si twisted pair control Fig C LG PI485 Gateway M board in condensing cable not supplied unit Fig D iZone C220
10. to the contrary the Warranty does not extend to cover damage to furniture carpets walls ceilings foundations vehicles or any other consequential loss arising either directly or indirectly due to the malfunction of the Product If a third party installer knowingly installs a defective Product the Warranty will be strictly limited to the resupply of that Product and shall not include any labour costs Repair or Replace During the Warranty Period Airstream will subject to clause 6 replace or repair any defective Product or defective component of a Product without subject to clause 8 charge provided that the defect does not constitute damage that has arisen from faulty improper incorrect or incomplete adjustment operation or installation of the Product any modification of the Product without the written approval of Airstream including tampering with or any attempt to disassemble the Product inadequate or improper maintenance of the Product misuse or abuse normal wear and tear failure for any reason to follow the instructions for use given in any user manual applicable to the Product act of God fire flood collision or other trauma or insects or animals Warranty Claim Procedure To obtain the benefit of the Warranty the Customer must contact Airstream within the Warranty Period or within seven 7 days of the discovery of the defect whichever is the earlier complete and send to Airstream the Warrant
11. 3 0 1 Constant CZCO V1 0 AC Control Zones CB V1 3 AC Temp displayed Set Points unlocked iSave disabled Components detected and i Fan Auto enabled software versions Auto Off disabled Filter Clean 6M o i i 6M This image is an example only Min Airflow locked Your screen may display differently depending on the system type what options are selected and the configuration settings entered by your installing contractor Some components and settings must be configured before h isplayed they can be displaye 26 3 0 System configuration WARNING Only qualified iZone installers should configure the iZone System Incorrect configuration could result in damage to your air conditioning unit and system To configure your system click on the System Config icon on the home page System Config Enter the system password wamfud and press the enter button The enter button must always be touched to save changes You will now be in the System Configuration area 27 3 1 Configuration main menu Note Information on the configuration screen may vary depending which devices are connected to the system and if it is an iZone 320 or 220 Monday 8Jun 2015 wa a z I system Configuration iZone Inventive Intelligent Intuitive 3 50 PM A Touch here to edit the number of zones installed Touch here to edit the number of variable electronic constant zones required Touch here t
12. Google play z N a Download from LE Windows Store Wireless Bridge iZone desk top PC App available from the iZone website Power supply Zone motors and CEXT not shown for clarity 1 13 iZone 320 Optional equipment for iSave addition up to 6 zones R Outside Air eam Air Damper 1 Air Damper 1 Return Outside Air Air Damper 2 Air Damper 2 Power supply Zone motors and CEXT not shown for clarity Use Zone 7 port on CC220 for Return Air dampers est Note Use Zone 8 port on CC220 for Outside Air dampers When the iSave option is used with an 8 zone system it is limited to a maximum of 6 Zones 18 1 14 iZone 320 Optional equipment for iSave addition 7 12 Zones ee n n Outside Air ower supply Zone Air Damper 1 motors and CEXT Air Damper 1 not shown for clarity Return Outside Air Air Damper 2 Air Damper 2 Use Zone 13 port on CEXT for Return Air dampers Use Zone 14 port on CEXT for Outside Air dampers Note When the iSave option is used with the CEXT the iZone system is limited to a maximum of 12 Zones 19 1 15 Optional equipment for Ethernet Home Automation connection Optional wireless communications between CB and CC220 CB Bridge CGB2C35 This special cable is specific for connecting the C220 and Wired Bridge Ethernet Power supply Zone motors and CEXT not shown for clarity 1 16 iZone 320 Wiring connection to AC units Take the P1
13. System initialisation 25 2 1 During initialisation 26 3 0 System Configuration 27 3 1 Configuration main menu 28 3 2 Zone setup 29 30 3 2 1 Sensor configuration 31 3 2 2 Pairing and configuring iZone RF sensors 32 3 2 3 Sensor calibration 33 3 2 4 iSense controller configuration 34 3 3 AC unit configuration iZone 320 only 35 3 3 1 Fan auto configuration 36 3 3 2 Fan auto zone area setup 3 3 4 System options Display Taglines Filter Maintenance Locks 38 39 3 5 WiFi bridge configuration 40 3 5 1 Manual IP configuration 41 3 5 2 WIFi connection 42 3 5 3 Smart phone tablet and PC configuration 43 45 3 6 Home automation integration 46 Table of contents Section Description Page No 4 0 User Manual 47 4 1 iZone 220 home screen 47 4 2 iZone 320 home screen 48 4 3 iZone 320 AC unit control 49 4 4 Zone control 50 4 5 Edit zone names and settings 51 4 6 Adjusting temperature controlled zones 52 4 7 Zone airflow summary 53 4 8 Changing zone airflows 54 4 9 Favourites 55 4 10 Assigning and editing favourites 56 4 11 Schedules Of 4 12 Setting and editing a schedule 58 4 13 Setting the time 59 4 14 Changing the home screen colour 60 4 15 iSense controller 61 4 16 Warranty registration 62 4 17 Airstream product warranty policy 63 4 18 Further assistance 64 Blank Page 1 1 iZone 220 Wiring layout for base system up to 8 zones CZDA Zone 1 Zone 2 Zone 4 Zone 3 Zone 5 Zone 7 5 z Zone Control Fa
14. and higher WINDOWS PHONE REQUIREMENTS e Compatible with Windows Phone 8 and 8 1 PC SOFTWARE REQUIREMENTS PC running Windows XP SP3 or higher Windows Vista Windows 7 Windows 8 Latest Windows service packs recommended WiFi modem or network switch e You will also need a compatible WiFi modem or network switch with a spare RJ 45 access port Some WIFI modems firewalls and security settings are not compatible with the iZone bridge and will need to be changed or replaced to enable the iZone app to run Download the iZone App e You will need an account with the manufacturer of your phone to enable you to down load Apps from their respective store e Apple Apple App Store e Android Google Play Store e Windows Microsoft Store e Login to the respective store e To search for the iZone App type iZone Controller into the stores search menu e Select iZone Controller and download the iZone App 43 3 5 3 Smart Phone Tablet or PC configuration Equipment Required and Configuration Equipment o See 1 11 amp 1 12 For details of equipment required and wiring diagram Configuration Power up the WiFi Bridge Press the System Config button on the touchscreen System Config Enter the system password wamfud Pair the wireless bridge to the iZone system Press and hold the blue button on the side of the Bridge At the same time press the Pair Wireless Device b
15. cates the iSense has been activated on this controller Press and hold the Airflow button to configure the controller Here you can configure the correct Zone to control and you can calibrate the sensor if required System reset button under here 34 3 3 AC unit configuration iZone 320 only Select method of controlling the AC unit Monday 8Jun 2015 3 50 PM Touch here to go to the home e R Air will control using the unit s return ee AC Unit Setup e Master will control the AC unit from the colour touch screen that has been AC Unit Controlling Sensor selected as the Master screen e Zones will automatically control the AC unit from the temperature controlled zones Fan Auto To configure Fan Auto see 3 3 1 Touch here to enable disable this feature Unit Auto Off Touch here to enable disable this feature AC Unit Info Touch here to view the fault history for his A it Indicates a Daikin AC unit module is this AC unit connected to this system iZone Inventive Intelligent Intuitive Touch here to go back and save the changes m 3 3 1 Fan auto configuration iZone 320 only Select the correct fan speed type for the system installed Refer to AC Unit Manufacturer manual Only available on certain AC unit makes Touch here to configure the zone areas Monday 8Jun 2015 3 50 PM Fan Auto Config Enable Fan Auto Control Capacities Select Fan Type Next Previous
16. e in 0230 Press the enter button to save your new setting Press here to go back to the schedule summary 58 4 13 Setting the time Current time Current date Press the left or right arrows to move to the value you want to change SQ Monday 8Jun 2015 Set Time Indicates the minutes are be 12k 01 01 2011 Date Month Year 234567890 WERTYU 0 P S DIF GH JIK LIF You must press the enter XCVBNM E Ait Space IZone n Inventive Intelligent Intuitive 4 14 Changing the home screen colour Monday 8Jun 2015 3 50 PM Screen Settings Slide left right to adjust the screen brightness Screen Adjustments Brightness Slide left right to adjust 7 i Slide left right to adjust the the screen saturation Contrast screen contrast Bac kg ro und Select Press the colour you would like for your home screen Fine adjustments to the shade tone hue can be made using the brightness contrast and saturation slides Press here to go back to the home screen IZone n Inventive Intelligent Intuitive 60 4 15 iSense controller Indicates system time Indicates zone name this unit is controlling Indicates zone setpoint temperature Indicates the iSense has been activated on this controller Indicates the maximum airflow set for this Indicates the air temperature inside zone the supply air duct Press to Op
17. e the A C unit settings 4 3 Press to change zone airflow 4 7 Press to activate a schedule or to configure a new schedule 4 11 Press to activate or deactivate this screens audio feed back beep on touch Tag line this will vary depending on the installation company Monday 8 Jun 2015 iz E system Is Off AC Unit al Sleep Timer fane Contra Favourites Zone Alrflaw schedule set Time screen settings isave is Off Beep system Coptic ione Inventive Intelligent Intuitive System date and time Press to change zone status 4 4 Press to toggle sleep timer options Press to activate a favourite mode or to configure a new favourite 4 9 Press to change screen settings 4 14 Press to set system time and date 4 13 Press to switch iSave On Only applicable if iSave has been fitted to the system Press to configure the system 3 0 A C system maintenance equired or A C unit fault code Press to clear WIFi connection 48 4 3 AC unit control iZone 320 only Monday 8Jun 2015 Press here to increase the AC unit set point Not applicable if AC unit controlling sensor Zones Cu AC uni ry i ie AC Unit Contro Increase a Press here to change the mode D l v set point Not applicable if AC unit eciEase controlling sensor Zones option selected See 3 3 option selected See 3 3 Press here to decrease the AC unit i f Indicat
18. ector switch to the correct i i same time press the paring button on the zone number touch screen and wait for the update to complete Press and hold Pairing button on the wireless device At the same time press the Pairing Button on the touch screen see 3 2 1 and wait until the update is complete 32 3 2 3 Sensor Calibration Monday 8Jun 2015 3 50 PM Re calibrated temperature for this ta Kitchen zone Calibrate sensor 22 2 J Down T Up Touch here to adjust the calibration down by 0 1 deg C Note Re calibration of the temperature sensor in the touch screens can only be done from the touch screen you want to re calibrate mad Back Inventive Intelligent Intuitive iZone Current reading with calibration offset included Touch here to adjust the calibration up by 0 1 deg C Total calibration offset from manufactured setting Touch here to go back and save the p changes 33 3 2 4 iSense controller configuration Press and hold the iSense button to enter the Occupancy Strategy configuration menu Follow the prompts to select the most appropriate strategy for your room or use the Custom Setup option to design your own strategy Note When iSense has been activated movement is required in the range of the occupancy sensor to keep the zone operating The use of the iSense feature in bedrooms when the occupants are asleep is not recommended Indi
19. en this zone fully Indicates the current zone temperature Press to Climate control this zone Adjust equired set point temperature using the up and down arrows Press to Close this zone fully Press to activate or de activate the iSense Press to adjust the maximum airflow to occupancy sensor this zone Use the up and down arrows to adjust the maximum airflow required to Note this zone When iSense has been activated movement is required in the range of the occupancy sensor to keep the zone operating The use of the iSense feature in System reset button under bedrooms when occupants are sleeping is here 1 not recommended 9 4 16 Warranty registration Your system is supplied with a standard 2 year warranty To extend your warranty you are required to complete this warranty registration form and email fax or post it to Airstream along with a copy of your invoice For terms and conditions please see Airstream s warranty policy at www air stream com au Full Name Contact Phone number including area code Email address f f If you have more than one iZone system please include additional registration forms iZone System ID number if applicable Address where the system is installed Date of purchase Instal
20. es Description Charges 165 00 plus GST 100 00 plus GST Call out fee plus first hour on Site Hourly labour rate after first hour on Site Replacement parts for Product and deliveries As per Airstream s current price list The Charges are subject to variation by Airstream from time to time Airstream will replace or conduct repairs to a Product as soon as practicable but will not be liable for any loss or damage caused by any delay Assignment The Customer may not assign or otherwise transfer the Warranty Airstream may at its sole discretion transfer or assign the Warranty Transportation Costs and Risk During Transit All transportation charges incurred in returning a defective Product or any defective component parts of a Product to Airstream for repair or inspection and the cost of returning them to the Customer must be paid by the Customer The Customer assumes the risk of and shall be responsible for any loss of or damage to any Product during transit For this reason Airstream recommends that the Customer take out shipment postage insurance Third Party Warranties Third Party Goods may be covered by independent manufacturer warranties It is the Customer s responsibility to familiarize itself himself or herself with these warranties No additional warranty is provided by Airstream for Third Party Goods 63 4 18 Further assistance 1 If you require warranty or maintenance on your air conditi
21. es the temperature measured Press here to change the fan by this panel is currently controlling di the AC unit Only applicable if systems configured for AC unit controlling sensor Master option AC unit actual temperature See 3 3 RA sensor or touch screen Normal 22 0 C Indicates the current status of the AC unit If a fault code Press here to go back to the appears here please contact home page your installer pag iZone Inventive Intelligent Intuitive 49 4 4 Zone control Indicates this zone is currently in climate control mode Zone Name Press to edit zone name and other zone settings 4 5 Indicates this zone is currently fully open Indicates this zone is currently closed Indicates the hall is an electronic constant and it is currently active Scroll up or down to see more zones Monday 8Jun 2015 3 50 PM iZone n Inventive Intelligent Intuitive Indicates Zone 1 temperature set point Press here to change the Set point 4 6 Indicates this zone is closed Press here to open the zone Indicates this zone is open Press here to close the zone Indicates there could be a fault with this damper Con tact your installer Indicates this zone is currently being overridden by the system and is being used as a constant because too many zones are closed Press here to go back to the home page 50 4 5 Edit zone names a
22. form available on the Website Warranty Period means for an iZone Tablet one 1 year for a Product excluding an iZone Tablet that has not been registered in accordance with clause 3 two 2 years or for a Product excluding an iZone Tablet that has been registered in accordance with clause 3 eight 8 years from the date of purchase by the Customer Website means the Airstream website at www air stream com au Warranty Subject to clauses 4 and 5 Airstream expressly warrants that each Product is free from operational defects in workmanship and materials for the Warranty Period Warranty The benefits of the Warranty are in addition to all other rights and remedies which the Customer may have under Australian Consumer Law and any other law in relation to the Product to which the Warranty relates Each Product comes with guarantees that cannot be excluded under Australian Consumer Law Extended Warranty In order to receive an extended eight 8 year Warranty for a Product Extended Warranty the Customer must register the Product by completing and providing to Airstream the registration form supplied in the Product user manual or downloaded from the Website Registration Registration must be completed within sixty 60 days of the Product being purchased by the Customer Exclusions to Warranty The Warranty does not cover Third Party Goods Subject to any statutory provisions
23. ine Touch here to change the filter clean reminder frequency Touch here to go back to the previous configuration page 38 3 4 System Options Locks Monday 8Jun 2015 3 50 PM 4 System Options Locks Note Information on the configuration screen may vary depending which devices are connected to the system and if it is an iZone 320 or 220 iZone Inventive Intelligent Intuitive Touch here to set limits for set point adjustment and to lock this setting Touch here to lock airflow adjustment You can lock minimum airflow only or both minimum and maximum air flow adjustments Touch to lock the AC Unit You will need to enter a PIN number and then the number of days you want the system to operate for until it is automatically locked off Do not forget your PIN Service charges will apply for a technician to attend site to unlock your system Touch here to go back to the previous configuration page 39 3 5 Wifi bridge configuration Monday 8Jun 2015 3 50 PM Touch here to go to the home Displays the iZone system ina y VAAL Bridge Config ID 123123123 Displays the Bridge IP address allocated by the DHCP IP 192 118 27 09 MAC 00 04 A5 G9 32 39 Displays iZone Ethernet controller MAC address Touch here to go back and save the Touch here to go to the manual WiFi changes configuration Next Previous P Back iZone Inventive Intelligent Intuitive 3 5 1 Manual IP Configuration
24. is zone can be changed by simply selecting the appropriate button Please note the correct hardware must be fitted for the zone to work correctly Previous iZone Inventive Intelligent Intuitive Press here to view or make changes to the wireless sensor status and configuration 30 3 2 1 Sensor configuration Monday 8Jun 2015 3 50 PM Hold down the Pairing Button on the iZone a Kitchen an wireless device see 3 2 2 Then press here to pair the device to your iZone Indicates the status of the wireless signal strength from the sensor in this zone It can take up to 10 minutes of normal operation to get an accurate reading To speed up the process press the Off Auto button on the sensor 5 times system Indicates the status of the battery in the sensor in this zone Press here to change the Rf Channel pe Displays the Radio frequency channel the system has been configured to This channel can be changed if RF interference is being experienced Press here to adjust the calibration of this sensor See 3 2 3 If the channel is changed all wireless devices need to be paired Touch here to go back and save any changes iZone Inventive Intelligent Intuitive 31 3 2 2 Pairing and configuring iZone RF Sensors Remove front cover from sensor Note To pair other devices such as an iZone bridge or repeater simply press the pairing button on the device and at the Set the zone sel
25. ite setting selected 56 4 11 Schedules Any of your favourites can be set to automatically start at any time of your choosing Press here to enable the time based schedule for favourite PM Nap Press here to set up or edit a schedule on any favourite Monday 8Jun 2015 3 50 PM Indicates an automatic time schedule has been enabled for this favourite PM Nap Watch TV Wake All Bedrooms Meals amp Living Dinner Party Living Dining User assign User assign Kitchen Indicates no automatic time schedule has been enabled for this favourite IZone n Inventive Intelligent Intuitive t Edit schedules 57 Indicates current schedule that you are changing or setting Indicates the start time for this schedule Indicates the stop time for this schedule Indicates the days this schedule will not run Press the day you want the schedule to apply to Press next to see the next schedule 4 12 Setting and editing a schedule Monday 8Jun 2015 24Hr Time Format START 08 00 STOP 17 30 Mon Tue Wed Thu Fri 1 2 Q W A S R TY U I FiG H J K Z xX V BNM db IZone n Inventive Intelligent Intuitive Space Previous Indicates the days this schedule will apply Press to stop the schedule running on this day Press here to clear this schedule Press the key pad to change the time Remember it is in 24 hour format so for 2 30 am typ
26. lation Company Proof of Purchase attached Yes No Signature Date Post fax or email your registration to Airstream Components 9 Geelong Court Bibra Lake WA 6163 Fax 08 9494 1346 Email info air stream com au 4 17 Airstream product warranty policy This document sets out the warranties that are provided by Airstream Components WA Pty Ltd ACN 146 196 778 Airstream in relation to each Product Definitions In this document Australian Consumer Law means the law set out in Schedule 2 of the Competition and Consumer Act 2010 Cth and any corresponding provisions of state or territory fair trading legislation Customer means the party that acquired the Product from Airstream for that party s use or if the party who acquired the Product from Airstream was an authorised distributor reseller or dealer the party who acquired the Product from the distributor reseller or dealer iZone Tablet means the product known as the iZone Tablet Product means an iZone Tablet or other product manufactured by or for Airstream Site means the place at which the Product is located Third Party Goods means a product including batteries or item of equipment manufactured by a third party which is supplied with or fitted to a Product Warranty has the meaning given in clause 2 1 Warranty Claim Form means the warranty claim
27. mp settings Current zone being edited System zone number and display name Current zone status Zone maximum and minimum air flow set points Status of this zone if it has been selected as an electronic constant Monday 8Jun 2015 Dining Room iZone 7 Inventive Intelligent Intuitive Press to edit zone name Press to edit current zone status Press to change maximum and minimum airflow set points Room area if Fan Auto function has been configured 51 4 6 Adjusting temperature controlled zones lates RE strength tom senso serving this zone is acceptable only if Monday 8Jun 2015 RF sensor is installed Indicates battery in the sensor serving D INI ng Room this zone requires replacement only if Indicates current zone being adjusted l RF sensor is installed increase ZX ay Press here to increase the current zone Indicates current temperature set point required for this zone set point temperature Press here to close this zone Open Close Press here to fully open this zone Climate NEGRI Press here to select this zone as the set point temperature Decrease iy Press here to decrease the current zone master only available if configured for Press here to allow iZone to automatically control the temperature in this zone system ductwork Indicates the actual temperature in this zone as measured by iZone Press here to go back to the
28. n 10m i See ee Oi fe sm sel gt ma u a no e i Gs Cia For wire length IV do dj tha ah shorter than 10m ec Groner on on SEB LE ayer Qe ec o eo a5 2S 4 Lowin W IL ee EN eer opt PAN seo Oe ID e ge sli ES i 8 Fig A Temperzone UC7 outdoor Correct polarity 20 BS gt Shielded 2 core e a twisted pair control cable not supplied Fig B iZone C220 C320TZ 23 1 19 General installation instructions 11 12 13 15 The C220 C320 and CEXT can be installed close to the indoor fan coil unit If any wireless sensor CRFS or wireless bridge CB is not within the range of the C220 then additional repeaters CR should be added to help relay the signal from the field device to the C220 Do not run the network cables alongside 240 Volt wiring When installing network cables down wall cavities or chasing network cables into walls tape up and protect the RJ45 connector to avoid damage to the connectors Installation damage to cables is not covered under warranty Always install zones in consecutive ports starting at Zone 1 The C220 and CEXT are marked with the zone port numbers Do not directly hardwire the CT24V into the AC unit s power supply This may void the warranty as it will require an electrician in the event that a repair of the iZone power supply is required Connect Zone Damper Actuators CZDA to the zone ports using the RJ11 cables as shown Connect the Colour Touch Screen
29. ng to use the App from outside the WiFi range When you login to iZone World Wide there is an option to save your username and password Login and Remember Me We recommend you select this option to make it faster and easier to login to your system remotely To reduce the data usage there may be a slight delay between changing a setting on your phone and the system updating when using iZone World Wide Do not use iZone World Wide when you are in your WiFi zone unless you have turned off the WiFi on your smart phone or tablet 45 3 6 Home automation integration iZone systems can be integrated into any home automation system that has an Ethernet interface The WiFi bridge is fitted with an Ethernet connection For interface specifications please download a copy of Airstream s Technical Catalogue at http www izone com au Your home automation integrator will need to write suitable code to control your AC system This service is not provided by Airstream or iZone 46 4 1 iZone 220 home screen To get back to the Home screen at any time press Home screen When entering names or values using the keyboard It is easier to use a thin object such as a toothpick Do not use sharp hard objects as they may damage the screen The enter button must always be pressed to save the changes you have made Press to change zone status 4 4 Press to change zone airflow 4 7 Press to set system time 4 13
30. o set up and configure each zone see 3 2 Touch here to set up AC Unit Configuration see 3 3 Touch here to pair wireless devices Touch here to enable iSave icons iSave components must be installed and electronic hardware set up accordingly Touch here to set up Options Touch here if you need to manually configure the IP address of the WiFi Bridge Touch here to change the system password Touch here to list the devices and software versions detected by this system Ba ck a Touch here to go back to the Home screen SOL 28 3 2 Zone set up Monday 8Jun 2015 3 50 PM 4 Zone Setup Touch here to go to the home screen If the zone has been named its name will chow here Indicates this zone is fitted with a wireless sensor Touch here to change Indicates this zone is designated to be the first electronic constant zone Indicates this zone temperature is controlled via the sensor in a touch screen Press here to change Indicates this zone is fitted with a wired sensor Touch here to change Indicates this zone has been set up for Open Close control only Indicates this zone is set up for temper ature control via an iSense controller iZone Inventive Intelligent Intuitive 29 3 2 Zone set up Monday 8Jun 2015 4 Kitchen Manual Control Indicates this zone has been configured to be climate controlled via a Wireless Climate Control Sensor The configuration of th
31. one Press here to decrease the maximum airflow to this zone Press here to increase the minimum airflow to this zone Press here to decrease the minimum airflow to this zone Press here to go back to the airflow summary 54 4 9 Favourites Press the favourite you would like and iZone will automatically change all the zones settings for this favourite Indicates this favourite has not been used Press here to setup and edit favourites Monday 8Jun 2015 Favorites k PM Nap Watch TW Wake All Bedrooms Meals amp Living Dinner Party Living Dining Wserassign User assign Kitchen XE Assign Favorites pagg Back IZone n Inventive Intelligent Intuitive 55 4 10 Assigning and editing favourites Monday 8Jun 2015 3 50 PM PM Nap PM Nap Zone names Living room 5 Indicates current favourite being changed Diningroom 4 Master bedroom John bedroom Up W Down pg Back IZone n Inventive Intelligent Intuitive Scroll up or down to see more zones Press here to change the name of this favourite Indicates what mode you want each zone to operate in when this favourite is used Change each zone setting to suit your requirements for this favourite If you require a different temperature to that indicated go to your zone and change it first Press here to go back to the favourites summary Pressing the back button will save the favour
32. oning system or iZone system you should contact your installation company 2 Ifyou want to add more zones or temperature control to any zone you should contact your installation company 3 If you require assistance from the manufacturer contact Airstream Components 9 Geelong Court Bibra Lake Western Australia 6163 Email info air stream com au Phone 61 8 9418 6631 www air stream com au www izone com au LIVING TECHNOLOGY airstream Rev 1 10 06 15 64
33. re modification or additional boards to facilitate the correct operation of the iZone system is the installing contractors responsibility 24 2 0 System initialisation All new or modified systems must be initialised prior to system configuration To initialise the system press the button on the underside of any colour touch screen This button is recessed so you will need to use a pen to press the button The time to initialise the system will vary depending on the number of motors connected The system will also initialise when power is restored after a power failure Progress bar will scroll while system initialises and tests all zone dampers Using a pen press the button on the underside of the screen Monday 8 Jun 2015 3 50 PM airstream LIVING TECHNOLOGY C220 V3 0 CZCO V1 0 CB V1 3 ID 000000215 14 Zones 1 Constant AC Control Zones AC Temp displayed Set Points unlocked iSave disabled Fan Auto enabled Auto Off disabled Filter Clean 6M Min Airflow locked Some components and settings must be configured before they can be displayed 25 2 1 During initialisation This screen will be displayed whenever the Monday 8Jun 2015 3 50 PM system is reset or when power is restored after a power failure None of the previous n settings or parameters are lost i Progress bar LIVING TECHNOLOGY IZONE 320 ID 000000215 System type CCTS V2 21 14 Zones Es system configuration settings C220 V
34. s CCTS to the iZone Net ports using the RJ45 cables If you are connecting more than 3 components requiring iZone Net ports to the system you will need to connect a Network Extension Module Kit CNEMK to one of the iZone Net ports on the CC220 using a short RJ45 cable If any zone is temperature controlled connect a Duct Temperature Sensor CDTS to the CDTS port Install the sensor into the supply air duct upstream of all dampers Secure the sensor in place by using reinforced aluminium tape When installing temperature controlled zones ensure the CCTS or sensor for the associated zone is installed in a location that is representative of the temperature in the room zone The sensor should be installed at approximately 1600mm above the floor and should not be subject to draughts direct sunlight or heat from equipment such as computers TV screens etc The supply air outlets to this room must not blow conditioned air directly onto the sensors or touch screens Connect the AC unit control cable to the C220 C320 See table 1 16 for details This cable is not supplied by Airstream The building must be fitted with a compatible WiFi modem Contact Airstream for a list of approved and recommended modems If connecting the iZone system to a Home Automation system use the Ethernet connection on the bridge Only connect the power supply to the CT24VAC port after all components have been connected Any existing or new air conditioning units that requi
35. th 1 colour touch of connection in AC screen shown above unit 1 16 O A maximum of 14 zones and 12 colour touch screens can be supported by one iZone sys tem See Network Extension Module 1 3 for Details 1 5 IZone 320 Wiring layout for base system 9 to 14 zones Zone 2 Zone 4 Zone 6 Zone 8 Zone 10 Zone 12 Zone 14 CZDA Zone 9 Zone 11 14 Zone system with 1 colour touch screen shown above Zone 13 A maximum of 14 zones and 12 colour touch screens can be supported by one iZone system See Network Extension Module 1 3 for Details Zone 1 Zone 3 Zone 5 Zone 7 Make sure you have the correct model for the make of AC unit AC Unit AC unit control cable See table for location of connection in AC unit 1 16 10 1 6 Optional equipment for wireless temperature controlled zones CRFS optional Wireless Temperature Sensors Max 14 per system CR optional Wireless Repeaters To extend wireless range CDTS Installed into the supply air duct off the fan coil unit Must be installed on all zone temperature controlled systems Power supply Zone motors and CEXT not shown for clarity 11 1 Optional equipment for wired temperature sensors CSM optional Install Sensor Module to allow for Wired temperature sensors CS CDTS SRI no n CS optional supply air duct o the fan coil unit Wired Temperature gt i Must be installed on milan
36. utton on the touchscreen Wait a few seconds Press the home button on the touch screen m The grey WiFi symbol should appear at the bottom of the home screen Connect the RJ 45 cable from the Bridge to the modem router The symbol will change to 100 green 44 3 5 3 Smart Phone Tablet or PC configuration Using your App Using your iZone App in your local WiFi area Press the iZone button on your phone or tablet izone A nine digit number will appear on at the top of the screen This is you system ID number Write it down as you will need it to register on iZone World Wide for control of your system away from home Press on the nine digit number and you will go into the App Now you can name your system using the Rename button 000000266 192 168 15 Do NOT press the iZone World Wide button unless you are registered for iZone world wide and you are outside your local WiFi area iZone World Wide Login iZone World Wide Service You can only have access to the system from outside your local WiFi range after you have subscribed to iZone World Wide To register on iZone World Wide Go to https worldwide izone com au signup Follow the prompts to subscribe You will need the system ID number This is a nine digit number You will also be asked for an email address and password which you should remember as you will need these to access your system when you are tryi
37. vorites Zone 6 Zone 8 8 Zone system with 1 colour touch screen shown above A maximum of 14 zones and 12 colour touch screens can be supported by one iZone system See Network Extension Module 1 3 for Details 1 2 iZone 220 Wiring layout for base system 9 to 14 zones CZDA Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Zone 9 Zone 10 Zone 11 Zone 12 14 Zone system with 1 colour touch screen shown above Zone 13 A maximum of 14 zones and 12 colour touch screens can be supported by one iZone sys tem See Network Extension Module 1 3 for Details Zone 14 1 3 Stand alone VAV systems Wiring layout for typical 4 zone system CZCO iSense wired one Controllers temperature and occupancy sensor Max 12 per system CDTS CZDA Zone 2 Zone 1 Zone 4 Zone 3 4 Zone system shown above CVAV4 A maximum of 14 zones and 14 iSense controllers can be supported by one iZone system For CVAV1 to CVAV3 no CNEM is required 1 4 iZone 320 Wiring layout for base system up to 8 zones CZDA Zone 1 sm gt i09 p Zone 2 Friday 10 Oct 20 Systems On ae Arties Schedule 4 Beep 3 z EO i a v Zone 3 Zone 4 CCTS Zone 5 Zone 6 Zone 7 Make sure you have AC Unit the correct model AC unit control cable for the make of AC See table for location unit 8 Zone system wi
38. y Claim Form accompanied by proof of purchase of the Product On receipt of the Warranty Claim Form and proof of purchase of the Product Airstream will contact the Customer to determine the extent of the issue or defect with the Product If there is an issue or defect with the Product that is covered by the Warranty then Airstream will at its sole option require the Customer at the Customer s expense to have the defective Product or defective component part delivered to Airstream or provided the Site is located in the Perth metropolitan area send an Airstream service technician to the Site to effect repairs to or replacement of the Product save that the reasonable travel expenses including travelling time of the technician must be paid by the Customer In order to complete repairs or replacement of a Product in accordance with clause 6 3 b Airstream requires safe and ready access to the Site and each Product including where required via scaffolding and access panels If Airstream considers access to the Site or Product to be unsafe or not readily available Airstream will not commence or will cease all work to repair or replace the Product All costs incurred in the obtaining of safe and ready access to the Site and Product shall be payable by the Customer Any services requested by the Customer outside of the scope of the Warranty will be charged to the Customer in accordance with the following schedule of charges Charg
Download Pdf Manuals
Related Search