USER MANUAL OF PROGRAM CARD
Contents
1. wire Use a program wire to connect the program box to the ESC at its program port Most of new ESC for RC cars uses this method to get rid of the trouble of disconnecting the Rx wire from receiver 2 types of program wires are available B Black R Red W White ia Program Wires for LCD Program Box Type A JR 3p ZH1 5 3p LCD Program Box Type B JR 3p JR 3p User Manual of Multifunction LCD Program Box HW SM805ENG 20130119 Page 2 of 2 c ESC hasn t built in BEC That is OPTO type ESC Software If the program port is multiplexed with Rx wire disconnect the Rx wire from receiver And then connect ESC to battery and and then plug it into the ESC port on the program box turn it on the USB Link Software will ry If the program port is not multiplexed with Rx wire use a program wire to connect try to communicate with the ESC After the program box to the ESC at its program port And an additional battery pack 4 8V the connection is established user A to 12 6V is needed to power the LCD program box via the Batt port can easily set the ESC or update its firmware on the PC o Throttle wire ESC OPTO Type Program Wire Program Box Battery for Program Box 1 2 Step B Connect ESC to battery and switch it on 3 Works as Lipo battery voltmeter a Battery 2 8S Lipo Li Lon Li Fe LCD program box shows the initial screen U1 press any button on the b Precision 0 1V2. LCD program box to communicate with the ESC the screen shows poaa c Usage after several seconds LCD shows the current profile name Mode and then Plug the balance cnarge connector oi the mode _car battery pack into the BATTERY CHECK port the 1 programmable item is displayed Please make sure that the negative pole Press ITEM and VALUE buttons to select the options press OK button to save the points to the symbol on the program box and then LCD shows the firmware the settings voltage of the whole battery and each cell a Reset the ESC by the LCD program box HORES T His Battery Lin tase When the connection between ESC and LCD program box is successfully Di ees established press ITEM button for several times till the Load Default Settings is e eee ee displayed press OK button then all programmable items in the current profile are reset to factory preset options Note When checking the voltage please supply the LCD program box only from the balance charge connector Don t supply LCD program box from Batt or USB port b Change profiles of the ESC UPDATE THE FIRMWARE OF LCD PROGRAM BOX Usually there are 3 profiles for different tracks conditions are stored in the ESC Note Sometimes the firmware of LCD program box should be updated because the functions of ESC XERUN 120A V3 and V3 1 ESC has 10 profiles for example Modified profile are improved continuous
3. User Manual of Multifunction LCD Program Box Thanks for purchasing the Multifunction Program Box for ESC Electronic Speed Controller Please read this manual carefully before using it FEATURE AND FUNCTION The Multifunction Program Box is the equipment for setting brushless speed controllers it works in the following 3 ways il 2 Works as an individual equipment to set the ESC the option of each programmable item is displayed on its own LCD screen Works as an USB adapter to link the ESC with PC to update the ESC firmware or set the programmable item by the USB Link Software on PC Works as a Lipo battery voltmeter to measure the voltage of the whole battery pack and each cell SPECIFICATION 1 2 3 Size 90mm 51mm 17mm Weight 65g Power supply DC 4 5V to 12 6V COMPARED WITH THE 2 IN 1 LCD PROGRAM BOX 1 The Multifunction Program Box uses new MCU microprocessor with more memories 2 times than the previous 2 IN 1 Program Box so only one firmware can be compatible with all soeed controllers The Multifunction Program Box has new function for Lipo battery voltage checking FUNCTION OF EACH BUTTON AND PORT hk a ITEM Button Change the programmable items and profiles circularly Exit the customized option setting process Enter the option setting process VALUE Button Change the options of each programmable item circularly Edit the option of each customized parameter c
4. ircularly R P Button Enter or return to the profiles selection menu OK Button Save the settings into the ESC Enter the customized option setting process HW SM805ENG 20130119 Page 1 of 2 Batt Port Provide power supply when an OPTO ESC that is ESC without built in BEC Battery Elimination Circuit is connect to the program box ESC Port Connect the ESC to program box from this port USB Port Connect the program box to PC and also provide working voltage to the program box If the USB port is connected then the power supply at Batt port is unnecessary BATTERY CHECK Connect to the balance charging connectors of the battery Note 1 Please pay attention to the polarity of the connectors Note 2 The space between pins is 2 54mm so the BATTERY CHECK port is compatible with XH EH and HP PQ connectors But Thunder Power battery uses different types of connectors so an adapter as below is needed 25 lt 4 6 P 7 i TP FP ADAPTOR 3 WORKING WAYS Works as individual equipment to set the ESC without PC Step A Connect ESC to program box correctly according to the different type of the ESC a ESC has built in BEC and the program port is multiplexed with Rx wire Disconnect the Rx wire from receiver and then plug it into the ESC port on the program box b ESC has built in BEC and the separated program port that is the program port is NOT multiplexed with Rx
5. ly Stock 10 5T profile etc It is very convenient for user to select the suitable profiles Connect the LCD program box with PC through USB port run Hobbywing USB Link Software in different tracks conditions select Device Multifunction LCD Program Box at the Firmware Upgrade module Press R P button to display the current profile name and then press VALUE choose the new firmware you want to use and then click Upgrade button button to change to next profile If there are some programmable options need to be Please detail instructions please browse the manufacturer s website changed in the profile please press ITEM button to enter the edit mode The detail information of the LCD Program Box The profile name can be changed by the USB Link Software on PC http www hobbywing com product_show asp id 215 2 Works as USB adapter to connect ESC to PC The detail information of the USB Link Software Connect the ESC LCD program box and PC according to the picture Run the USB Link http www hobbywing com product_show asp id 218
Download Pdf Manuals
Related Search