Home

User's Manual PMM 1008

1. Fig 1 2 Front Panel Legend 1 LCD display 2 Functional keys 3 Operate led 4 Stand by led General Information narda Safety Test Solutions 1 8 Rear panel SAFETY WARNINGS O BEFOR BI P CABI INT CABLING CONNECT PROTECTIVE EARTI O DO NOT REMOVE COVER A REFER SERVICING TO QUALIFIED PERSONNEL ONLY Fig 1 3 Rear Panel Legend 1 Mains plug IEC CEE22 2 power switch 3 RS232 485 interface DB9 4 User I O port DB15 5 current output connector 9 14 mm bolt General Information 15 narda Safety Test Solutions _ This page has been left blank intentionally General Information narda Safety Test Solutions 2 Installation 2 1 Introduction This section provides the information needed to install your PMM 1008 Included is information pertinent to initial inspection power requirements line voltage power cables interconnection environment instrument mounting cleaning storage and shipment 2 2 Initial inspection Ee WARNING To avoid hazardous electrical shock do not turn on the instrument when there are signs of shipping damage to any portion of it 2 3 Packing and Inspect the shipping container for damage Unpacking If the shipping container or cushion material is damaged it should be kept until the contents of the shipment have been checked for completeness and the instrument has been c
2. narda Safety Test Solutions Setting test time From this menu it is possible to set the test time pressing the TIME key will appear the following display SET Max Safety Time Setting maximum Using the and keys it is possible to set the maximum test time in the test time range 1 12000 minutes the minimum step is 1 minute Pressing the BACK key will return in previous menu setting open level and test time Executing the test Before to do the test it is necessary to execute a calibration To execute the test follow these steps execute a calibration select the test level using NEXT key press ON key Pressing ON key the display will show the following Cont Lev 1 1 Am 0 20 5 0 98A m In the second row at the left there is the indication of time in seconds In the second row at the right there is the indication of the field calculated considering the output current and the antenna factor In fact the field is obtained from H lx f where is the current flowing into the loop and f is the antenna factor 0 87 for a square loop of 1m x 1m Starting the test after pressed the ON key the PMM 1008 will move the internal variac at the position stored during the calibration from this position the generator will regulate the position of the variac to obtain the correct output current The test will go on up to the maximum time set it is possible to stop the test pressing the STOP key D
3. 2 1 Continuous test mode 3 2 3 2 2 Short test mode 3 4 23 2 39 EXSCUIING A 16h 3 6 3 2 4 Manual mode nnn 3 7 32 o SET UP MONU EE 3 8 3 2 0 Seting antenna Ce e 3 9 3 2 7 Error E e uiecisturte sene thor mie oa e 3 10 4 References Page 4 1 Heierences i 4 1 4 2 Induction CO l nn 4 1 5 How to program Page 5 1 OIG ioc EE TT 5 1 ENEE EIERE enee 5 1 SOON O PRE TATE i 5 1 SAU 5 1 SE Eet 5 1 5 6 PMM1008 Setting COMMANOS ees 5 2 5 7 PMM1008 Query commande 5 3 6 Firmware Upgrade Page 6 1 TOC WO MN NER RR n 6 1 6 2 System reouiremente nenne 6 1 6 3 To install the software nrnna 6 1 6 4 Icon of PMM 1008 software 6 2 6 5 UPGRADE Procedure se sisrriinni t E 6 2 Contents m narda Safety Test Solutions Figures Figure Page 1 1 mie E caucasian 1 3 1 2 FROMM COAG IEW MINN VO OO C 1 4 1 3 Roar panel PMM TOOG Tc 1 5 4 1 Characteristics of the field generated by a square induction coil 4 1 4 2 3dB area of the field generated by a square induction coil 4 2 4 3 30B area of the field generated by a square induction coil in the orthogonal plane 4 2 Tables Table Page 1 1 Technical SpecificatiOnS iii 1 2 4 1 So aig ile alio MENTRE S 4 2 SNO AUAN NE Tm T TT Contents narda Saf
4. by a safety interlock connected at user port in the rear panel The connections are the following Ee i WARNING To use the PMM 1008 is necessary to insert the HD Key The interlock can be used to insert an external safety switch like in the following draw Installation narda Safety Test Solutions 3 Operating instructions 3 1 Starting PMM 1008 PMM 1008 has been designed with a user friendly interface to be used by EMC engineer as well by non skilled personnel For a better safety must connect all cable before connected the Magnetic Field Generator at distribution Network and not disconet anything befor end of test For connect the Magnetic Field Generator at distribution network Ee WARNNG must used only a appropriate cable includ in the PMM 1008 For connect the instrument at distribution network don t use extension lead or adapter 3 2 Main menu display Connect the power supply cable and HD Key to the rear panel connector and switch on the standby led will switch on All functions can be recalled by the four functional keys located on the bottom of LCD display When instrument is turned on the firmware initiates the internal testing procedure If everything is OK the display will show PMM 1008 Rel release number CONT SHRT MAN The main commands are CONT to select continuous test menu SHRT to select short duration test menu MAN to select manual test menu SET to select setting menu L NOTE
5. 00S4 level in the range 4 5 indicated short magnetic 800 A m will be generated which refer to the field level related field Note that this command is not recognized if received X is the open level within sub menus If PMM 1008 is generating 00B a magnetic field this command Breaks it abruptly Then it leads to top of menus 52 How to program narda Safety Test Solutions 5 7 PMM 1008 Query commands Command Explanation Example 0071 joies i value of the generated 00 i 00 L Pons fe status of interlock 00 L 00 0 Returns whether the generator is 00 0 00 0 generating ON or not OFF the field 007E Returns the ERRORs accumulated 00 7E 00 e since the error register was last gt ERR 5 read This example shows that there Note that once this register is read W detected 2 errors it is automatically reset 1 Argument out of range 1 2 Th d The result has the following uan it meaning The resulting error is 1 mE 441 25 The argument supplied is out of range or inadequate Menu ERROR A command has not been executed because it was not allowed in the present menu The Command was not recognized because is unknown 256 First read after switch ON More type of error are accumulated so that a composite error flag can be detected How to program 53 narda Safety Test Solutions _ This page has been left blank intentionally Ho
6. Before to do the test execute the calibration procedure Document 1008EN 90413 1 25 NARDA 2007 Operating Instruction 31 narda Safety Test Solutions _ 3 2 1 Continuous test Activating the function key under the CONT you will enter the continuous mode test menu that shows Cont Lew SET ON Setting open level In the top of the display there is the indication of the level with reference to the standard The levels available are Level 1 1 A m Level 2 3 A m Level 3 10 A m Level 4 30 A m Level 5 100 A m Level X open in the range 1 100 A m Pressing the NEXT key it will be changed the level selected and the indication will appear in the top of the display Select your field and press ON to start the test Pressing the SET key the display will show the following Cont L ev 1 OFF LEVX TIME Setting LEVX Using this menu it is possible to set the level of Level X and the time of the open level test Pressing LEVX the display will show the following SET Continuous Level Using the and keys it is possible to set a test level in the range 1 100 A m Pressing the CAL button the PMM 1008 will do a calibration of the output current level With this operation the instrument will move the internal motor variac to set the correct current this position will be stored for the test Pressing the BACK key will return in previous menu setting open level and test time 32 Operating Instruction
7. MM 1008 will start the test the operate led will switch on and will play a continuous beep The test will go on up to the maximum time set it is possible to stop the test pressing the STOP key Operating Instruction narda Safety Test Solutions 3 2 4 Manual mode Manual mode stand by Using this function it is possible to do a test and change the field level during test this feature can help to measure the level of susceptibility of the equipment under test Pressing the MAN key the display will show the following Manual Mode Band Selection 10A 100A Choosing 10A key or 100A key the PMM 1008 will enable the output current the operate led will switch on and the display will show the following In the second row left side there is the time increasing indication in the right side the indication of the field Manual Mode 0 12 35 F 25A m DN STBY BACK Pressing the and keys it is possible to increase or decrease the field level If the band selected is 100 A the maximum current is 160 A and the maximum field depends from the antenna factor If the band selected is 10 A the maximum current is 16 A the maximum field depends from the antenna factor but the resolution using the and key is higher Pressing the STBY key the PMM 1008 will disable the output current the operate led will switch off and will show the following display The and keys are disabled pressing the ON key
8. NARDA equipment need servicing you can help us serve you more effectively filling out this card and enclosing it with the product Nevertheless even this product will eventually become obsolete When that time comes please remember that electronic equipment must be disposed of in accordance with local regulations This product conforms to the WEEE Directive of the European Union 2002 96 EC and belongs to Category 9 Monitoring and Control Instruments You can return the instrument to us free of charge for proper environment friendly disposal You can obtain further information from your local NARDA Sales Partner or by visiting our website at www narda sts it M Servizio richiesto M Service needed L Solo taratura L Riparazione L Riparazione amp Taratura O Taratura SIT LI Altro Calibration only LI Repair L Repair amp Calibration CO Certified Calibration LJ Other Ditta Company Indirizzo Address Persona da contattare Telefono Technical contact person Phone n Modello Numero di serie Equipment model Serial n M Accessori ritornati con l apparecchiatura O Nessuno O Cavo i LJ Cavo di alimentazione Altro v Accessories returned with unit None C Cable s LJ Power cable Other M Sintomi o problemi osservati kl Observed symptoms problems M Guasto O Fisso Intermittente Sensibilea O Freddo O Caldo UL Vibrazioni O0 Altro M Failure L1 Continuous O Intermittent Sensitive to LI Cold L Heat TT Vibration TT Oth
9. acters used inside the strings are in ASCII format 00 127 at 7 bit The most significant bit are ignored in reception and put to 0 during transmission C 0 Every strings starts with the special character and stops with 5 4 Address The address cannot be assigned but is fixed at FM The PMM 1008 can also answer at address 00 5 5 Format All messages are content between and characters for strings send to Host PC and between 00 and for strings send to the instrument The string sent to the PMM 1008 has the following format 00c c Where Start character 00 c 6 Command End character PMM 1008 will respond with the following string c c In this case the address is not used because the PC does not need it Between C C there is the message text where the length can varies from 1 to 100 characters Document 1008EN 90413 1 25 NARDA 2007 How to program 53 narda Safety Test Solutions _ 5 6 PMM 1008 setting commands Explanation Example e 00V Instrument Type amp 00V Version gt PMM1008 rel 1 0 8 98 00Cn where n is the Starts generating the 00C2 level in the range 1 5 indicated continuous 3 A m will be generated which refer to the magnetic field level related field Note that this command is X is the open level not recognized if received within sub menus 00Sn where n is the Starts generating the
10. ciascun commento e suggerimento sottoposto all attenzione della nostra organizzazione tenuto in grande considerazione La nostra qualit e alla ricerca del miglioramento continuo Se uno dei Suoi strumenti NARDA necessita di riparazione o calibrazione pu aiutarci a servirla pi efficacemente compilando questa scheda e accludendola all apparecchio Tuttavia anche questo prodotto diventer obsoleto In questo caso ti ricordiamo che lo smaltimento dell apparecchiatura deve essere fatto in conformit con i regolamenti locali Questo prodotto conforme alle direttive WEEE dell Unione Europea 2002 96 EC ed appartiene alla categoria 9 strumenti di controllo Lo smaltimento in un ambiente adeguato pu avvenire anche attraverso la restituzione del prodotto alla NARDA senza sostenere alcuna spesa Pu ottenere ulteriori informazioni contattando i venditori NARDA o visitando il nostro sito Web www narda sts it Dear Customer thank you for purchasing a NARDA product You now own a high quality instrument that will give you many years of reliable service NARDA recognizes the importance of the Customer as reason of existence in this view any comment and suggestion you would like to submit to the attention of our service organization is kept in great consideration Moreover we are continuously improving our quality but we know this is a never ending process We would be glad if our present efforts are pleasing you Should one of your pieces of
11. ecified to be within the following limitations e Temperature 10 to 40 C e Humidity 80 31 50 40 e Altitude lt 4000 meters The instrument should be stored in a clean dry environment The storage and shipping environment is specified to be within the following limitations e Temperature 40 to 50 C e Humidity lt 95 relative e Altitude lt 15000 meters 2 7 Return for service If the instrument should be returned to NARDA for service please complete the service questionnaire enclosed with the Users Manual and attach it to the instrument To minimize the repair time be as specific as possible when describing the failure If the failure only occurs under certain conditions explain how to duplicate the failure If possible reuse of the original packaging to ship the equipment is preferable In case other package should be used ensure to wrap the instrument in heavy paper or plastic Use a strong shipping container and use enough shock absorbing material around all sides of the equipment to provide a firm cushion and prevent movement in the container To prevent damage during shipment in particular protect the front panel Seal the shipping container securely Mark the shipping container FRAGILE to encourage careful handling 22 Installation A narda p Safety Test Solutions 2 8 Equipment cleaning Use a non abrasive clean soft and dry cloth for equipment cleaning NW CAUTION To clean the equipment d
12. ent level With this operation the instrument will move the internal motor variac to set the correct current this position will be stored for the test Pressing the BACK key will return in previous menu setting open level and test time From this menu it is possible to set the test time pressing the TIME key will appear the following display SEI Short Time Using the and keys it is possible to set the maximum test time in the range 1 5 seconds the minimum step is 1 second Pressing the BACK key will return in previous menu setting open level and test time Operating Instruction 35 narda Safety Test Solutions _ 3 2 3 Executing a test SW CAUTION Before to do the test it is necessary to execute a calibration To execute the test follow these steps execute a calibration select the test level using NEXT key press ON key Pressing ON key the display will show the following short Lev 4 400 A m 301 5 A m ONT 4 55 s STOP In the second row at the right there is the indication of the field In the third row there is the indication of the decreasing time in seconds Starting the test after pressed the ON key the PMM 1008 will move the internal variac at the position stored during the calibration After this operation the PMM 1008 will start the test procedure and for 5 seconds will advise with a beep every one second without any output current after these 5 seconds the P
13. er Descrizione del guasto condizioni di funzionamento Failure symptoms special control settings description Se l unit parte di un sistema descriverne la configurazione If unit is part of system please list other interconnected equipment and system set up Suggerimenti Commenti Note Suggestions Comments Note
14. ety Test Solutions WW SAFETY RECOMMENDATIONS AND INSTRUCTIONS This product has been designed produced and tested in Italy and it left the factory in conditions fully complying with the current safety standards To maintain it in safe conditions and ensure correct use these general instructions must be fully understood and applied before the product is used When the device must be connected permanently first provide effective grounding If the device must be connected to other equipment or accessories make sure they are all safely grounded In case of devices permanently connected to the power supply and lacking any fuses or other devices of mains protection the power line must be equipped with adequate protection commensurate to the consumption of all the devices connected to it In case of connection of the device to the power mains make sure before connection that the voltage selected on the voltage switch and the fuses are adequate for the voltage of the actual mains Devices in Safety Class equipped with connection to the power mains by means of cord and plug can only be plugged into a socket equipped with a ground wire Any interruption or loosening of the ground wire or of a connecting power cable inside or outside the device will cause a potential risk for the safety of the personnel Ground connections must not be interrupted intentionally To prevent the possible danger of electrocution do not remove any covers panels
15. factor for a square loop are Rectangular loop 2 6x1 0 66 Operating Instruction narda Safety Test Solutions 3 2 6 Setting antenna Pressing the FACT key from the setup menu the display will be the factor following SET Coil Factor Pressing and keys the PMM 1008 will change the antenna factor When it is changed an antenna factor it is necessary to do a calibration because the setting saved refers to a different current for the same level Operating Instruction narda Safety Test Solutions _ 3 2 7 Error message If the antenna is disconnected after some seconds the PMM 1008 will display the error message LOOP OPEN In this case check all the connections between the generator and the antenna Operating Instruction narda Safety Test Solutions 4 References 4 1 References The preferential range of test levels respectively for continuous and short duration application of the magnetic field is given in Table 4 1 e 4 2 Table 4 1 Continuous field Table 4 2 Short duration 2 3 J4 2 Notapplicable 3 AJ 10 J 3 Notappliable 4 2 30 4 3S0 5 2140 j JX O toO 4 2 Induction coil The PMM 1008 is supplied with a 1 meter square coil The following figures describe the field uniformity for this kind of tool A i e M es 6 1 Es Z Se 4 0 3 02 057 0 40 j E e VA IM Y a Fa E Es z d
16. hecked mechanically and electrically Verify the accessories availability in the shipping referring to the accessories check list enclosed with the Users Manual Notify any damage to the carrier personnel as well as the NARDA Representative 2 4 Preparation for use This is a Safety Class equipment it is provided with a protective earth terminal An uninterruptible safety earth ground must be Ee WARNING provided from the main power source to the product input wiring terminals through the power cable or supplied power cable set Verify the safety earth ground functionality before operation Before connecting this instrument ensure that an uninterruptible safety earth ground is provided from the main power source to the product protective earth connection If this instrument is to be WARNING connected to other equipment or accessories prior to energizing either unit verify that a common ground exists between them Any interruption or loosening of the protective earth ground conductor either inside or outside the unit or in an extension cable will cause a potential shock hazard that could result in personal injury Document 1008EN 90413 1 25 NARDA 2007 Installation 21 narda Safety Test Solutions _ 2 5 Power cable This instrument is equipped with a three wires power cable When connected to an appropriate AC power receptacle this cable grounds the instrument chassis 2 6 Environment The operating environment is sp
17. ical specifications Frequency Range 50 Hz Remote control System interface RS 232 485 Connector DB9 User port Two function HD Key Interlock Display 4 lines LCD 20 characters Power supply AC 230 VAC 10 Max current 16A Output voltage Without load Max 4Vac Output current Max continuos Max short a Modes Continuous Short Manual Ramp Internal timer Continuous mode Short mode 1 12000 min 1 5 sec Timer resolution Continuous mode Short mode 1 min 1 sec Size Generator Loop 365 x 200 x 480 mm WxHxD Truck 1030 x 35 x 1030 mm WxHxD Mast antenna 550 x 210 x 650 mm WxHxD Cables 1900 mm H 95 mm 1 5 mm Weight Generator Loop 28 Kg Truck 6 Kg 25 Kg 12 General Information A narda E Safety Test Solutions x ee E i Creo ue end et ISDN UE MAGNETIC RED Cetucg 1008 Fig 1 1 PMM 1008 General Information 13 narda Safety Test Solutions _ 1 7 Front panel O MM MAGNETIC FIELD GENERATOR 1000 O C C OPERATE C i a SE Ja C lt 3x gt C ju C C SE SE d C gt gt La s Re i e C SS ac 3x pre C gt C DC E gt C gt 2 ke O C gt C D C gt C SICH ML C Se Jet oa F via c PE Q
18. ification and has been designed to meet the requirements of EN61010 1 Safety Requirements for Electrical Equipment for Measurement Control and Laboratory Use wy This product has a Pollution Degree Il normally only non conductive pollution occurs Occasionally however a temporary conductivity caused by condensation must be expected The information contained in this document is subject to change without notice KEY TO THE ELECTRIC AND SAFETY SYMBOLS You now own a high quality instrument that will give you many years of reliable service Nevertheless even this product will eventually become obsolete When that time comes please remember that electronic equipment must be disposed of in accordance with local regulations This product conforms to the WEEE Directive of the European Union 2002 96 EC and belongs to Category 9 Monitoring and Control Instruments You can return the instrument to us free of charge for proper environment friendly disposal You can obtain further information from your local Narda Sales Partner or by visiting our website at www narda sts it Warning danger of electric shock Earth Read carefully the Operating Manual and its instructions pay attention to the safety symbols Unit Earth Connection Earth Protection p BE E Equipotential GY IH KEY TO THE SYMBOLS USED IN THIS DOCUMENT The DANGER sign draws attention to a potential risk to a person s safety DANGER All the precautions must be fully
19. m those documented in this manual 1 3 Introduction to PMM 1008 is a magnetic field generator system at power frequency The PMM 1008 generator is a current generator and the indication of the field is obtained considering the antenna factor the system includes the antenna formed by one coil and the antenna mast The correct output current is automatically set and regulated by the generator PMM 1008 is designed to meet all the requirements contained in the EN 61000 4 8 standard and to cover all the levels described in continuos and short mode 1 4 Instrument items PMM 1008 includes the following items e Magnetic field generator e power cable e square loop 1m e two cables connecting generator and square loop e one generator support with 4 screws e one antenna support with six screws e antenna mast e truck e user manual e Hardware Key DB15 1 5 Optional accessories The optional accessories are e Square loop 1 5m e Square loop 2m e Circular loop 1m e Rectangular loop 2 6x1m e Antenna mast for square loop 1 5m or rectangular loop 2 6x1m e Second antenna mast for square loop 1 5m or 2m or rectangular loop 2 6x1m Document 1008EN 90413 1 25 NARDA 2007 General Information 14 narda Safety Test Solutions _ 1 6 Main specifications Table 1 1 lists the PMM 1008 performance specifications The following conditions apply to all specifications e The ambient temperature shall be 10 to 40 C TABLE 1 1 Techn
20. narda Safety Test Solutions Sales amp Support Via Leonardo da Vinci 21 23 20090 Segrate MI ITALY Tel 39 02 2699871 an B Communications Company http www narda sts it Fax 39 02 26998700 Manufacturing Plant Sa ta Via Benessea 29 B n 17035 Cisano sul Neva SV ez Tel 39 0182 58641 Wi Fax 39 0182 586400 Y SERIAL NUMBER OF THE INSTRUMENT User s Manual PMM 1008 MAGNETIC FIELD GENERATOR You can find the Series Number on the rear panel of the instrument Series Number is in the form 0000X00000 The first four digits and the letter are the Series Number prefix the last five digits are the Series Number suffix The prefix is the same for identical instruments it changes only when a configuration change is made to the instrument The suffix is different for each instrument Document 1008EN 90413 1 25 Copyright NARDA 2007 narda Safety Test Solutions NOTE If the instrument is used in any other way than as described in this Users Manual it may become unsafe Before using this product the related documentation must be read with great care and fully understood to NW familiarize with all the safety prescriptions To ensure the correct use and the maximum safety level the User shall know all the instructions and recommendations contained in this document This product is a Safety Class and Installation Category Il instrument according to IEC class
21. o not use any solvent thinner turpentine acid acetone or similar matter to avoid damage to external enclosure 2 9 System Installation PMM 10068 is a system with different parts and an installation needing To install the PMM 10068 following the steps indicated 1 Connect the cables to the loop using the screws as shown in the next figure 2 Position the loop into the teflon support as shown in the next figure Installation 23 A narda Safety Test Solutions 3 Lock the loop to the support using the six screws Installation A narda Safety Test Solutions 4 Lock the antenna mast on the truck using the screw on the bottom Installation 25 A narda Safety Test Solutions 5 Put the generator support on the truck and the loop support on the mast in the position desired using the screw mounted on the support The final mounting should be the following 6 Put the generator on his support on the truck 7 Connect the cables from the loop to the output current connector in the PMM 1008 generator rear panel 8 Insert HD Key on the USER PORT Connector rear panel Installation A narda E Safety Test Solutions WARNING The antenna produces magnetic field the field is high in the center of gei the loop set the generator positioning outside of the loop like in the previous figure Installation 2 7 narda Safety Test Solutions _ 2 10 Safety Interlock The PMM 1008 is provided
22. or guards installed on the device and refer only to NARDA Service Centers if maintenance should be necessary To maintain adequate protection from fire hazards replace fuses only with others of the same type and rating Follow the safety regulations and any additional instructions in this manual to prevent accidents and damages Safety consideration narda Safety Test Solutions EC Conformity Certificate in accordance with the directives EMC 89 336 EEC and low voltage 73 23 EEC This is to certify that the product PMM 1008 Magnetic field generator Produced by NARDA S r l Safety Test Solution Via Benessea 29 B 17035 Cisano sul Neva SV ITALY complies with the following European Standards Safety CEI EN 61010 1 2001 EMC EN 61326 1 2007 This product complies with the requirements of the Low Voltage Directive 2006 95 CE and the EMC Directive 2004 108 CE NARDA S r l EC Conformity narda Safety Test Solutions 1 General Information 1 1 Documentation Enclosed with this manual are e a service questionnaire to send back to NARDA in case of equipment service is needed e an accessories check list to verify all accessories enclosed in the packaging 1 2 Instruction Manual Instruments manufactured after the printing of this manual may have a changes series number prefix not listed on the title page this indicates that instruments with different Series Number prefix may be different fro
23. the PMM 1008 will go back in the previous menu and pressing the BACK key will stop the Manual Mode Stand By DN ON BACK manual mode and will go back in main menu Operating Instruction 3 7 narda Safety Test Solutions _ 3 2 5 SET UP menu Using the set menu it is possible to calibrate the system or to change the antenna factor It is important to execute the calibration before to do test Pressing the SET key from the main menu the display will be the following Calibration menu Pressing the CAL key it will be possible to calibrate the system the display will be the following CALIBRATION CONT SHRT FULL BACH The calibration will store the position of the internal variac to obtain a current output current for the field level selected In this way starting the test the PMM 1008 will move the variac in the stored position and then will regulate around it The calibration can be done for the continuous test CONT or for the short test SHRT or both Pressing CONT key the PMM 1008 will calibrate all the continuous test levels pressing SHRT key the PMM 1008 will calibrate all the short test levels pressing FULL key the PMM 1008 will calibrate both the test continuous and short In the setting mode it is also possible to change the antenna factor The antenna factor depends from the shape and the dimensions of the antenna setting a different antenna factor it is possible to use a different antenna The antenna
24. understood and applied before proceeding My The WARNING sign draws attention to a potential risk of damage to the WARNING apparatus or loss of data All the precautions must be fully understood and applied before proceeding The CAUTION sign draws attention against unsafe practices for the ei CAUTION apparatus functionality Ce NOTE The NOTE draw attention to important information n Note and symbols narda Safety Test Solutions Contents General safety considerations and instructions V EC Conformity Certificate IeHeee VII 1 General Information Page 1 1 Pere Bi E el p MN PR m 1 1 1 2 Instruction Manual changes nennen 1 1 1 3 Introduction to PMM 1008 eese 1 1 1 4 Instrument itemS e 1 1 1 5 Optional acceseories Li 1 1 1 6 Main specifiCatiONs i 1 2 VF Font rst 1 4 1 8 Rear panel Em 1 5 2 Installation Page Ce ang dee leie onina 2 1 2 2 Initial INSPECHION e 2 1 2 3 Packing and unpackimg eas 2 1 2 4 Preparation for use nn 2 1 2 5 ae 2 Ee 0 NUN ER 2 2 2 5 EE Ee 2 2 2 7 Return for SErvice nennen 2 2 2 8 Equipment cleaning eee 2 3 2 9 System installatioN i 2 3 2 10 Safety InterloCkK en 2 8 3 Operation instructions Page 3 1 Starting PMM 1008 i 3 1 3 2 Main Bun Dn Re Te EE 3 1 3
25. uring the test the Operate led will switch on and will play a sound beep every 3 seconds Operating Instruction 33 narda Safety Test Solutions _ 3 2 2 Short test mode CAUTION Wait five minutes between three short test cycles Using this test it is possible to do a short test with an high level of field in fact the maximum current is 1250 A for a maximum time of 5 seconds Pressing the SHRT key the display will be the following Short Lev 4 5 s SET ON BACK Setting test time In the top of the display there is the indication of the level with reference to and open level the standard The levels available are e Level4 300 A m e Level 5 1000 A m if antenna factor is 2 0 87 otherwise is 1000 0 87 K e Level X open in the range 300 1000 A m depending from antenna factor Pressing the NEXT key it will be changed the level selected and the indication will appear in the top of the display Setting LEVX level Pressing the SET key the display will show the following short Lev 4 OFF LEVX TIME Using this menu it is possible to set the level of Level X and the time of the test Pressing LEVX the display will show the following SEI Short Level Operating Instruction narda Safety Test Solutions Setting test time Using the and keys it is possible to set a test level in the range 300 1200 A m Pressing the CAL button the PMM 1008 will do a calibration of the output curr
26. v dE Fig 4 1 Characteristics of the field generated by a square induction coil 1m side in its plane Document 1008EN 90413 1 25 NARDA 2007 narda Safety Test Solutions _ Fig 4 2 3dB area of the field generated by a square induction coil 1m side in its plane Fig 4 3 3dB area of the field generated by a square induction coil 1m side in the mean orthogonal plane component orthogonal to the plane of the coil Refer to the CEI EW 61000 4 8 for further information References narda Safety Test Solutions 5 How to program 5 1 Introduction PMM 1008 has been designed to be programmed through his serial port using either RS232 as well RS485 When using RS232 you can use only one instrument connected to PC serial port If using RS485 you can connect up to 31 instruments to the same PC serial port PMM 1008 uses the same connector for both communications 5 2 Communication Half duplex communication is implemented The protocols are identical for RS232 and RS485 A built in automatic tool identifies the type of communication used and shows it on LCD display Typical communication is implemented at 9600 baud with 8 bit one stop bit and no parity 5 3 Protocol Be aware that only the PC can send the commands PMM 1008 will answer when is inquired only Communication is done at 9600 Baud with 8 bit 1 stop bit and no parity The communication uses strings with variable byte width The char
27. w to program narda Safety Test Solutions 6 Firmware Upgrade 6 1 Introduction PMM 1008 has been designed to be programmed through its serial port using either RS232 as well RS485 Using RS232 it is possible to upgrade the firmware of the instrument at the latest release 6 2 System requirements For the software to operate properly the user s Personal Computer should be equipped with the following 486 Processor or Pentium 16 Mb of RAM at least 10 Mb of free space on hard disk 1 free serial port Windows Operating System 95 98 6 3 To install the The Update Firmware Program can be installed using the software diskette software and running SETUP PMM 1008 Update Setup PHM 1008 Update Setup If you want to install the test application in a different directory and or drive type the name of the directory Install To SILE To quit Setup choose the Exit button Continue When the installation is complete the following window will be displayed PHM 1008 Update Setup Document 1008EN 90413 1 25 NARDA 2007 Firmware Upgrade narda Safety Test Solutions _ 6 4 Icon of PMM 1008 Once the software has been installed in the PC the related icon will be software displayed Press PMM 1008 FirmWare Update twice for running the update program 6 5 UPGRADE Procedure 1 Switch off the PMM 1008 2 Connect the serial cable between the PC and PMM 1008 3 Run the upgrade software the main windo
28. w will be displayed UPGRADING UTILITY 2 3 037 2000 COMM 7 il ES Switch ON PMM en za RS 485 1008 4 Switch on the PMM 1008 5 When the upgrade procedure is completed correctly the software will display the following message PHM UPGRADE 5 1 Tumaffthe UNIT amp turn it op again PMM 1008 is now updated with the new version of the internal firmware It is now possible to disconnect the cable connected to the PC with the PMM 1008 either switched on or off Subsequently when the apparatus is switched on the new version of the firmware will be displayed on the display of PMM 1008 To obtain updating of the firmware or programs for PMM 1008 the LC 4ANOTE user can contact his NARDA agent or download it directly from the following Web site www narda sts it Firmware Upgrade Sales amp Support Manufacturing Plant i NARDA n d rd d Safety Via Leonardo da Vinci 21 23 Via Benessea 29 B E I Test 20090 Segrate MI ITALY 17035 Cisano sul Neva SV 8 Safety Test Solutions tens Tel 439 02 2699871 Tel 439 0182 58641 A d an E Communications Company S r l Socio Unico Fax 39 02 26998700 Fax 39 0182 586400 gamer COT http www narda sts it Mod 18 1 Caro cliente grazie per aver acquistato un prodotto NARDA Sei in possesso di uno strumento che per molti anni ti garantir un alta qualit di servizio NARDA riconosce l importanza del Cliente come ragione di esistenza

User's Manual PMM 1008

Contents

Download Pdf Manuals

Related Search

Related Contents