Home

A0620115 Meteor-100RGB Underwater Pool Light Operating

1. 1 Optical window High grade polycarbonate glass optical window 2 Underwater pool light casing Stainless steel casing with fixing holes and cable gland 3 Cable The 4 pole multi core cable to connect the 12 24Vdc power supply and optional remote control or switch 4 Fixing screw The fixing screws to fix the underwater pool light on the wall INSTALLATION The underwater light kit consists of the following components e Underwater Light METEOR 100 RGB 4 x fixing screw 5 5x38 with wallplugs Operating Instructions with Declaration of Conformity and Warranty conditions The METEOR 100 RGB has to be installed on a flat surface on the pool wall under water line Do not try to install the underwater pool light while the pool is filled with water When the installation is finished briefly test the underwater light prior to fill the pool with water The installation have to be realized by a qualified personnel Sealing Wall Screw 5 5X38 Sealing Grooves 2X Note Avoid using the underwater pool light out of the water for more than 2 minutes The underwater pool light is protected by a temperature sensor against over heating When the temperature of the underwater pool light exceeds 85 C the underwater pool light is automatically switched off Wall preparation The underwater pool light is recommended to be installed around 0 2 m below the waterline for the best illumination and to avoid over heating To fix
2. Color is set and selected Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination Set default Press the key switch for min 40 seconds or until the light is turned off Synchronization When more than one multi color underwater pool light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode If the multi color light is used only with one of the fixed color of lighting the synchronization is not necessary TECHNICAL SPECIFICATIONS Power supply 12 24 Vdc max 680 mA 12 Vdc max 380 mA 24 Vdc Advised Powersupply 12Vdc PLN 30 A9900350 Advised Powersupply 24Vdc PLN 30 A9900360 Lens angle 60 Optical window High grade polycarbonate glass Luminous flux max 650 Lm Protocol default address 1 Operating temperature 10 C 50 C Casing Stainless steel 316L Protection IP68 Dimensions 99 x 9 mm Weight 0 4 kg Design and specifications subject to change without notice Highlite international BV Vestastraat 2 NL 6468 EX Kerkrade The Netherlands ARTECTA Division Phone 31 0 45 5667734 Fax
3. years from the date of purchase by the user Proof of purchase must be included to establish that it is inside the warranty period 3 This Warranty is transferrable and covers the product for the specified time period 4 n case any part od the equipment proves to be defective other than those parts excluded in paragraph 5 below the owner should do the following a prepare a detailed written statement of the nature and circumstances of the defect to the best of the Owner s knowledge including the date of purchase the place of purchase the name and adress of the installer and the Purchaser s name adress and telephone number b the Owner should return the defective part or unit along with the statement referenced in the preceding paragraph to the warrantor ARTECTA or an authorized ARTECTA distributor postage shipping prepaid and at the expense of the Purchaser c if upon the Warrantor s or authorized distributor s examination the defect is determined to result from defective material or workmanship the equipment will be repaired or replaced at the Warrantor s option without charge and returned to the Purchaser at the Warrantor s expense d no refund of the purchase price will be granted to the Purchaser unless the Warrantor is unable to remedy the defect after having a reasonable number of opportunities to do so Prior to refund of the purchase price Purchaser must submit a statement in writing from a professional boating equip
4. 3 Puls dim controller Puls dim controller Puls dim controller Puls dim controller Puls dim controller Puls dim controller A9915100 LSUO8 Puls dim controller Puls dim controller Puls dim controller Puls dim controller a DECLARATION OF CONFORMATY Supplier Details Name Highlite International BV Address Vestastraat 2 6468EX Kerkrade The Netherlands Product Details Product Name Meteor 100 RGB Ordercode A0620115 Trade Name Artecta Applicable Standards Details 1 EMC Directives 2004 108 EC EN 55015 2006 A1 2007 EN 61547 1995 A1 2000 A2 2009 EN 61547 2009 2 Low Voltage Directives 2006 95 EC EN 60598 1 2004 A1 2006 Supplementary information The conformity to above standards is verified by Astel d o o Declaration hereby declare under our sole responsibility Name Issued Date that the product mentioned above to which this declaration relates complies with the above mentioned S ildiz April 22 2011 standards and Directives m EE N Highlite International BV p Ss Vestastraat 2 6468 EX Kerkrade The Netherlands WARRANTY 1 The equipment is warranted by ARTECTA to be free from defects in workmanship and materials under normal use and service 2 This Warranty is in effect for of two
5. 31 0 45 5667709 E Mail artecta ghighlite nl 1 Lsuos Sync control for one group RGB LED fixtures LED 12 24V DC Power supply tob Puls dim Puls dim Puls dim controller controller controller Meteor Meteor Meteor Meteor 230V AC Meteor Meteor Group A Group B Group C Group D Group E Group F OO KO KO KO3 ex GG ip DC Power supply n 4 Meteor Meteor Meteor Meteor 230V AC Meteor Meteor Group A Group B Group C Group D Group E Group F DIDI wax SS i DC Power supply ay ip Meteor Meteor Meteor Meteor 230V AC Meteor Meteor Group A Group B Group C Group D Group E Group F DIDI se SS D DC Power supply D A9915100 LSU08 Puls dim Puls dim Puls dim controller controller controller 2 LSUO8 Sync control for max 6 groups LED RGB fixtures Meteor Meteor Meteor Meteor Group D 230V AC LED 12 24V DC Power supply Meteor Group E Meteor Group F ys Meteor Group A Meteor Meteor Meteor Group D LED 12 24V DC Power supply Meteor Group F eC 3 Meteor Group E LED 12 24V DC Power supply C Se Meteor Group F eC
6. e LED technology ART A0620115 Meteor 100RGB Underwater Pool Light Operating Instructions CONTENTS iz EM 3 GAUSS ECT ATENTO ELM 3 PrecautionS ii E CR 3 Components and Conneclors auch mm 4 Installation u a FFR FWY RF YF FRWNT nie 5 onis 7 79 e1 Ez M6 E E E E E TRETEN 8 Technical Specifications PT 8 Declaration On Taerar 9 PREFACE The METEOR 100 RGB series of a compact ultra thin underwater pool light with built in driver is designed to use the latest LED lighting technology The surface mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max diameter of the hole through the wall is 8 mm The METEOR 100 RGB with 316T stainless steel casings is available with RGB colors with 6 highpower LEDs The multi color RGB version allows changing of the color of lighting manually or automatically through the complete rainbow spectrum The most advanced electronic design with built in microprocessor enables network connection and simple control of complete group of lights with dimming PRECAUTIONS The underwater pool light has to be installed and used in accordance with the instructions of this manual only e The power supply has to be disconnected before installation e The underwater pool light i
7. ment supplier that the installation instructions of the Operating Instructions manual have been complied with and that the defect remains e warranty service shall be performed only by the Warrantor or an authorized distributor and any attempt to remedy the defect by anyone else shall render this warranty void 5 There shall be no warranty for defects or damages coused by faulty installation or hook up abuse or misuse of the equipment including exposure to excessive heat salt or fresh water spray or water immersion except for equipment specially designed as waterproof 6 There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees and representatives for injury to any person or persons or damage to property loss of income or profit or any other consequential or resulting damage or cost which may be claimed to have been incurred through the use or sale of the equipment including any possible failure or malfunction of the equipment or part thereof 7 The Warrantor assumes no liability for incidental or consequential damages of any kind including damages arising from collision with other vessels or objects
8. s recomended to be installed around 0 2 m below the water line for the best illumination and to avoid over heating The optical window must be clear and not covered by any kind of isolating or other material The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge Do not use abrasive or highly alkaline cleaners e Never scrape with razor blades or other sharp instruments Benzene leaded gasoline acetone or carbon tetrachloride should never be used Do turn power off immediately and refer servicing to qualified service personnel if the underwater pool light does not operate normally following the operating instructions FEATURES APPEARANCE Innovative DesignS tainless Steel Ultra Thin Casing 6 Power LEDs Design White Red Blue Green or Multi Color RGB Lighting High Grade Polycarbonate Glass Optical Window Vacuum Metalized Reflector Remote Control Built in ASTEL Protocol for DMX512 Control of Multi Color RGB version Digital Dimming Polarity Protection Transient Protection Thermal Protection 8 Wide Range Power Supply Low Power Consumption Simple Installation Optional accessories for different pools installations 5m 4 Pole Multicable pog Powersupply DC Black Powersupply DC Orange Pulse Control Brown Pulse Control GND Stainless Steel 316L stainless steel 316L Fixing Screws ae High grade polycarbonate glass optical window
9. simple key switch not included has to be used and connected to the CONTROL wires by the 2 pole signal cable not included Optional PWM dimmer LDU13 can be connected to the CONTROL wires by using a 2 pole signal cable not included Optional LXU01 or LXUOS interfaces can be connected to the CONTROL wires by using a 2 pole signal cable not included DMX512 control The network connection to control the lights with the standard DMX512 protocol is enabled by using optional PWM dimmer LDU13 and optional LXU01 or LXUOS interfaces METEOR 100 RGB CONTROLS Sequence of lighting Custom Color Remote control has to be used to turn on and turn off the underwater Full RGB pool light and to control the mode of lighting and luminosity Cool White The multi color underwater pool light can be controlled by using the Bluish White key switch Red Green When the light is turned off the color or mode of lighting can be Blue changed sequentially by pressing the momentary switch for 2 Rainbow Color Spectrum seconds Turning on off Press the key switch momentary Changing the color or mode of lighting When the light is turned off press the key switch for 2 seconds Setting the Custom Color At the selected Rainbow Color Spectrum mode press the key switch momentary to turn the light off After that press the key switch for 5 seconds or until the light is switched to the selected color and then the Custom
10. the underwater pool light with screws 5 5x38 the diameter of holes drilled into the wall has to be 8 mm The diameter of the hole for cable gland drilled through the wall has to be 8 mm Sealing Before inserting the cable with gland through the hole the sealant has to be used into the grooves around the four fixing holes and around the gland in the rear surface of the underwater pool light The sealant can be on silicon basis but the best solution is two component polymer sealant Fixing The underwater light has to be fixed with four screws 5 5x38 with wallplugs Note Do not overtighten the screws as this can result in underwater pool light damage Earthing The underwater pool light has to be earthed by using a pre tinned green wire with a yellow stripe a minimum of 8 AWG 8 36 mmo The wire has to be connected to the underwater pool light by the help of one fixing screw 5 5x38 Connection The power supply has to be connected through the main switch not included with correct polarity and protected by a fuse not included The power supply voltage has to be from 10 30Vdc Note e The power supply has to be switched off before installation The underwater light has to be connected as described in the table below METEOR 100 RGB FUNCTION wire color Red DC Power Supply Black GND Power Supply Orange Control Brown GND Control Remote control connection To control the mode of lighting the

A0620115 Meteor-100RGB Underwater Pool Light Operating

Contents

Download Pdf Manuals

Related Search

Related Contents