Home

Operating Instructions

image

Contents

1. CONFORMITY FOR MACHINES Directive 89 392 CEE Annex II paragraph A GS Engineering amp Development Ravenstein hereby declares that sweeper GS 0900 R conforms to the provisions of the Directive relating to machinery directive 89 392 CEE as amended lately and the national legislation implementing this directive and furthermore declares that the following parts of harmonized standards have been applied EN 292 1 Machine safety part 1 Made in Ravenstein 29 May 2007 A A W Giesbers Technical director GS Engineering B V 20 manufacturer hydraulic sweepers
2. 4 3 1 Tensioning of V belt The V belt can be adjusted by the user What do you need Socket spanner 7 Spanner 10 Spanner 13 Follow the procedure below to adjust the tension of the V belt 1 Use Wrench 7 to loosen the screws on the grey protective cover of the GS O900 R The protective cover has four screws see Fig 1 amp 2 Fig 1 Fig 2 2 Use spanner 10 to loosen the bolts indicated by the arrows Turn to the left see Fig 3 amp 4 Fig 3 GS Engineering B V 16 manufacturer hydraulic sweepers Instructions GS 0900 R a O 3 Now you can tension the V belt using Spanner 13 see Fig 5 Turn to the right to tighten it The V belt should not be adjusted too tightly This could cause damage to the electromotor This can be tested as follows Check if the tensioned V belt can be pushed in 2 5 cm 2 5C V belt Fig 6 Schematic bottom view of the GS 0900 R GS Engineering B V 17 manufacturer hydraulic sweepers Instructions GS 0900 R 4 3 2 Spare fuse Under the protective cover an additional fuse has been attached with a tie wrap First demount the protective cover see 4 3 1 Next cut the tie wrap Fig 1 GS Engineering B V 18 manufacturer hydraulic sweepers Instructions GS 0900 R Maintenance Dates GS Engineering B V 19 manufacturer hydraulic sweepers Instructions GS 0900 R EC DECLARATION OF
3. A visual check is enough After prolonged use a period of more than 30 days without being used or unexpected circumstances the sweeper must be thoroughly checked Bolts and nuts must be checked regularly for tightness 4 2 Maintenance after sweeping After sweeping the machine can be cleaned no water may be used to clean the machine Cleaning with a dry or damp cloth is permitted 4 2 1 Battery charger A battery charger is supplied with the GS 0900 R as a standard accessory Fig 1 GS Engineering B V 14 manufacturer hydraulic sweepers Instructions GS 0900 R First connect the battery charger to the GS 0900 R before putting the plug into the socket Once the battery is full the charging stops The connecting point of the battery can be found at the bottom of the push bar Put the plug of the battery charger into this point see Fig 2 The battery level has to be checked frequently The minimum and maximum level of the battery are indicated on the side of the battery see Fig 3 If necessary top up with demineralised water L a So o on Y Fig 3 GS Engineering B V 15 manufacturer hydraulic sweepers Instructions GS 0900 R For further information on the battery of the GS 0900 R please refer to the battery manual that is also supplied with the sweeper 4 3 Maintenance and repairs Maintenance and repairs to the machine must be carried out by a mechanic
4. Instructions GS 0900 R Operating Instructions GS 0900 R GS Engineering B V l manufacturer hydraulic sweepers Instructions GS 0900 R Manufacturer GS Engineering amp Development Phone 31 0486 415370 Fax 31 0486 411325 E mail info gsengineering nl Machine GS 0900 R You can also download these operating instructions from our website www gsengineering nl GS Engineering B V 2 manufacturer hydraulic sweepers Instructions GS 0900 R Table of Contents 1 General 4 1 1 User 5 1 2 Liability 5 1 3 Warranty conditions 6 1 4 Documentation accessories 6 1 5 Technical data 7 2 Safety 8 2 1 Safety symbols 9 2 2 Safety aspects 9 2 3 Emergencies 10 2 4 How the sweeper should not be used 10 3 The sweeping process 11 3 1 Recommended use 11 3 2 Brush 11 3 2 1 Starting and stopping the brush 11 3 2 2 Height adjustment 12 3 3 Accessories 13 4 Maintenance and control 14 4 1 Check before starting to work with the GS 14 O900 R 4 2 Maintenance after sweeping 14 4 2 1 Battery charger 14 4 3 Maintenance and repairs 16 4 3 1 V belt tensioning 16 4 3 2 Spare fuse 18 Maintenance dates 19 EC Declaration 20 GS Engineering B V a manufacturer hydraulic sweepers Instructions GS 0900 R 1 General These operating instructions intend to set forth the correct use of the GS 0900 R lt addresses all aspects that are of relevance to the operation and daily maintenance of the GS 0900 R I
5. ar Furthermore hairs could be pulled out by the sweeping process As a result it could become necessary to adjust the height of the brush In case of severe wear various parts of the brush where a lot of hairs are missing or poor sweeping results the brush must be replaced The user can adjust the height of the brush by simply turning the black turn knob see Fig 1 on top of the brush Release the wing nut first Turning to the right the distance between the surface to be swept and the hairs of the brush is increased Turning to the left the distance between the surface to be swept and the hairs of the brush is reduced Turn the brush up after use turn to the right This way it does not lose its shape GS Engineering B V 12 manufacturer hydraulic sweepers Instructions GS 0900 R 3 3 Accessories e Brush speed control e You can always order parts and accessories Please contact your dealer for more information GS Engineering B V 13 manufacturer hydraulic sweepers Instructions GS 0900 R 4 Maintenance and control 4 1 Check before starting to work with the GS 0900 R Before starting any activity several things must be checked first check if the machine is in good condition For instance check for parts that may loosened due to vibration check the air pressure of the tyres 2 0 bar check if there are no persons or animals in the immediate surroundings of the G S 0900 R
6. ition GS Engineering B V 10 manufacturer hydraulic sweepers Instructions GS 0900 R 3 The sweeping process 3 1 Recommended use The sweeper is mainly used for cleaning straight surfaces The material to be swept will largely consist of leaves rubbish snow sand gravel or a combination hereof The sweeping of certain materials may generate large clouds of dust The use of protective glasses is therefore compulsory Particles may fly up due to the sweeping method The operator has to make sure that there are no persons or animals in the direct surroundings of the machine 3 2 Brush 3 2 1 Starting and stopping the brush A control switch has been mounted on the push bar to switch the brush on and off The GS 0900 R has 3 brush positions Right rotation left rotation and neutral To activate the brush right rotation turn the switch to position R Turn the switch to position L see Fig 1 for left rotation 0 indicates the neutral position Fig 1 GS Engineering B V 11 manufacturer hydraulic sweepers Instructions GS 0900 R lf the brush jams move the sweeper back If the brush continues to be jammed turn it off and have it checked by a mechanic Never check the brush when the sweeper is running Make sure that the brush has come to a complete stop before changing the direction of the brush 3 2 2 Height adjustment Depending on the use the brush hairs are liable to we
7. mechanic is the person who carries out repairs or maintenance works to the machine The mechanic must be qualified to perform technical operations The mechanic must have a solid understanding of technical matters and be able to read technical drawings Before the operator and mechanic operate or service the machine they must have been adequately instructed The first instruction is given by specialists from GS This does not apply when a company already has several machines of the same type or when there is sufficient knowledge available within a company GS cannot be held responsible in any way for works that have been carried out by an operator who is not or not sufficiently instructed or qualified 1 2 Liability These operating instructions and the data they contain have been drawn up with the utmost care GS and or your supplier are not liable for a possible lack of clarity mistakes and or damages to the GS 0900 R or personal injuries In addition they are not liable for personal injuries caused by incorrect use or attempts to have the sweeper serviced by others that are not qualified mechanics GS Engineering B V 5 manufacturer hydraulic sweepers Instructions GS 0900 R 1 3 Warranty conditions The warranty terms mentioned in the general terms and conditions of delivery will lapse immediately by operation of law if 1 service activities and or repairs have not been carried out strictly in accordance with the instr
8. o act according to circumstances at all times With each movement the machine makes the operator must be certain that there are no persons near the machine lt is not permitted to use the machine to transport people When using the machine safety glasses must be used GS Engineering B V 9 manufacturer hydraulic sweepers Instructions GS 0900 R The operator s clothing must be tight fitting preferably no loose clothing In addition the operator must wear sturdy footwear All maintenance repairs remedies of defects and other similar activities not mentioned in these operating instructions must be carried out by a mechanic lf the operator detects any defect or fault to the machine a mechanic has to be notified immediately 2 3 Emergencies An emergency means a situation in which people animals and or the machine are in danger or danger threatens them lf an emergency arises the operator must bring the machine to a standstill and turn off the electromotor In case of damages to the machine or other situations in which machine parts might have been affected the machine must be thoroughly checked This is the only way to guarantee safe operation of the machine even after an emergency 2 4 How the machine should not be used lt is not allowed to sweep materials that affect human health in any way whatsoever The sweeper must never be put on its side during the Sweeping process or when in stop pos
9. pertly safety instructions are not being observed Therefore anyone who Is involved in the operation maintenance and or repair of the machine has to read and follow the safety instructions If so desired this could be confirmed by the user s signature Apart from the requirements and regulations mentioned in these operating instructions the following apply general safety requirements land specific regulations GS Engineering B V g manufacturer hydraulic sweepers Instructions GS 0900 R 2 1 Safety symbols The safety symbols on the machine must be complete and legible at all times Damaged and illegible safety symbols must be replaced by new ones 1 Applied to the machine housing behind the engine read operating instructions before use 2 Applied to the frame under the push bar this is the CE mark and serial number 3 Applied to the brush casing possible physical injury if instructions are not followed correctly 2 2 Safety Aspects The safety aspects and pictograms included in these operating instructions as well as the safety symbols on the machine must always be observed by the operator The procedures set out in the operating instructions must always be executed in the correct order When operating the machine the operator must always see to proper visibility so he can see the work area and the machine He has to make sure that his attention is not distracted from his work and has t
10. t also pays attention to important aspects of technical maintenance The operating instructions must be carefully read in order to use the machine correctly and safely The text in these operating instructions is printed in the following ways Normal text is printed in normal type Important information is printed in bold Options are printed in italics The following pictograms are used to draw attention to issues that require special attention and or involve risks for persons the machine and or the sweeping process Text preceded by this sign requires special attention Warning Instructions preceded by this sign warn you about the risk of damage to the machine or malfunctioning if the instructions are not followed carefully Physical injury Text preceded by this sign warns of physical injury if the instructions are not followed carefully GS Engineering B V 4 manufacturer hydraulic sweepers Instructions GS 0900 R 1 1 User In these operating instructions user means Anyone who is put into contact with the GS 0900 R or parts thereof under normal operating conditions The company or user has to make sure that each user is sufficiently qualified to handle this kind of machines and is able to comply with relevant provisions and safety aspects A clear distinction is made between two groups The user is the person who actually operates the machine in preparation or execution of the production process The
11. uctions 2 Repairs have not been carried out by service mechanics from GS engineering or its official dealer or have been carried out by the customer s mechanics without written approval from GS 3 Changes have been made to the delivered product without prior written approval from GS 4 Other than original GS parts are used 5 Other than the prescribed lubricants are used 6 The delivered product is handled improperly carelessly incorrectly and or negligently 7 The machine is used for other purposes than those it was designed and built for 1 4 Documentation accessories The following is supplied with the machine the operating instructions for the GS 0900 R battery charger for the GS 0900 R warranty certificate GS Engineering B V 6 manufacturer hydraulic sweepers Instructions GS 0900 R 1 5 Technical Data Technical data of the GS 0900 R Fig 1 Sweeping width 90 cm Engine power Electrical 12V 0 45Kw Brush drive V belt Brush left right rotation Yes Brush diameter 900 mm GS Engineering B V 7 manufacturer hydraulic sweepers Instructions GS 0900 R 2 Safety The GS 0900 R has been manufactured in accordance with the regulations that are currently applicable Nevertheless this machine could cause dangers to man and machine if it is not operated in accordance with the operating instructions it is not operated by qualified personnel it is changed or used inex

Download Pdf Manuals

image

Related Search

Related Contents

Tripp Lite Standard Power Extension Cord, 13A, 16AWG (NEMA 5-15P to NEMA 5-15R), 1-ft.  Género no Abastecimento de Água,Saneamento e  IECSoft - Caltest Instruments  Toastmaster BTW09 User's Manual  Pulse Counter & binary data acquisition available on the  User manual  Hampton Bay EP266WH Use and Care Manual  少年自 少年自  Manuale dell`utente - Migros  Adam Equipment AZplus 15 Building Set User Manual  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.